Haier Washer WMS656 User Manual

WMS656  
Twin-tub Washing Machine  
Contents  
Before using  
Names of the parts.............the 2nd cover  
Safety precautions ...............................1  
Installation and adjustment ..................3  
Introduction of the major functions .......5  
Using process  
Preparation before washing ................6  
The musts in washing .........................7  
Usage of the detergent .......................8  
Washing sequence ..............................9  
Disposal after washing .......................13  
Please read this manual carefully before using.  
Retain it for future reference  
Trouble-shooting*  
Answers to question.....................15  
Please check if the power receptacle has good earthing  
condition before using to guarantee your safety.  
Packing list ......................................17  
Specification..............the back cover  
The manufacturer will not bear the responsibility for  
those risks occurred from not obeying this manual.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Safety precautions  
Please insert the power cord into special  
When the machine is normally using, please  
put the power plug at the location easily to  
be inserted and extracted by hand. Be sure  
to pull the plug off when there'spower failure,  
or the machine is being moved, cleaned or  
when it is idle.  
receptacle with rated voltage.Be sure to  
use single-phase three pins receptacle.  
The earthing terminal of the receptacle  
must be earthed reliably.If possible,please  
adopt electric leakage protector.  
Earth  
If the power cord is bad, to avoid risk it is required to replace it by the technicians of  
our special shop or the after-sale service department. Keep the pin of the power  
plug clean.  
Do not use water hotter than 50 C .  
In case the washing machine is installed  
on ground with carpet , do not block the  
ventilation hole with carpet.  
Ventilation hole at  
the bottom of the  
washing machine  
Do not wash water-proof laundries such  
as the raincoat, bicycle shelter etc. To  
avoid abnormal vibration during spinning.  
Do not put the machine at damp place  
like the bathroom . Never wash it with  
water. Do not place wet laundries on the  
control panel.  
Do not share one receptacle with other  
electric appliances. Do not use it in  
case that the power plug is damaged  
or the inserting into the receptacle is  
loose.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Safety precautions  
Do not stretch hands into the working  
Do not decompose, repair or alter the  
machine by yourself.  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.  
Do not put any hot or heavy items  
( such as the kettle with hot water )  
on the washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
er  
Petrol  
Thinn  
Handicapped or children without care  
shall not use the machine.  
Keep the machine away from direct  
sunlight and heat source like the  
heater.  
Toprotect your laundries and washing  
machine, please take out all of the coins,  
buttons, sand, hairpin and other foreign  
materials before washing.  
Please check if the water faucet is open, and if  
the connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
Usage of the drain hose  
The drainage shall be smooth with the drain hose.  
1.The height of the drain hose shall be  
less than 10cm , or the drainage will  
not be smooth enough and cause  
incomplete drainage.  
<10cm  
2.Do not tramp or press the drain hose.  
3. If the drain hose is too long, cut it at mid point.  
To make smooth drainage, cut the front end of  
the hose slantingly.  
>
30mm  
4.If extra drain hose is needed , please make  
separate purchase. The inner diameter of the  
extra hose shall not less than 30mm, and the  
length shall not exceed 1.5m.  
<1.5m  
5.If the extra hose is too long, cut it either  
at point A or B.  
A
B
Install the lint filter  
After opening the package,please take out the  
lint filter from the document bag,install it  
to the overflow filter of the cabinet.  
See to the figure  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
How to change the direction of the drain hoses  
Side sectional view  
Figure 1 indicates the ex factory installation  
position of the drain hose.  
Back  
Front  
Soft item  
Extend the drain hose from the side of wash tub  
Figure 1  
Put soft items on the ground. Lean the machine  
down gently with the front surface facing the  
ground. Take off the drain hose from the cabinet.  
Take the hose out of the fixing groove.  
(See to Figure 2).  
Soft item  
Figure 2  
Embed the drain hose into the groove along the side  
of thewash tub in the order of (1)~(2), heading for the  
side of the wash tub. (See to Figure 3).  
Embed the drain hose into the groove with  
hands. Take care not to damage the drain  
hose in fastening the fixing clamp.  
Figure 3  
Figure 4  
Extend the drain hose from the rear side  
Take out the drain hose from the fixing groove. Extend it from  
the rear side as per the direction of the arrow. (When the drain  
hose is extended from the rear side, it can be hung on the  
point for drain hose at the two sides of the cabinet.)  
(See to Figure 4).  
Select the water level  
Select water level according to the  
quantity of the laundries.  
Set the water level adjusting lever  
to needed line.  
Water level  
indicator  
Max.  
Med  
Min  
Maximum  
about 43L  
Page8  
Medium  
about 36L  
Minimum  
about 30L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before process  
Introduction of the major function  
The machine has good comprehensive performance, and nice appearance.  
It adopts streamline appearance and full plastic shell, which will never get rust.  
For the design on safety and reliability, it adopts the wash shelf, spin shelf and water  
inlet groove design, and reduces the unfavorable influence on the electrical component  
by the vapor. Therefore it guarantees more safe and reliable washing.  
It adopts complete enclosed base frame and low-noise motor, and thus reduces the  
working noise significantly. We can guarantee that the purchase of this machine will bring  
you a clean world without disturbing your quiet life.  
Filling water from wash water-filling entrance  
Use the new water inlet hose provided with the  
machine to connect to the water faucet.Old hose  
sets should not be reused.  
Water inlet hose  
Water-filling  
entrance  
Push  
Insert the water inlet hose into the water-filling  
entrance, then push the water-filling jointer into  
the wash water-filling entrance on the major frame.  
(To dismantle the water inlet pipe, just push the  
control handle as indicated in the figure and pull it out)  
Wash water inlet  
Control handle  
Foam-removing spinning during high-efficiency rinsing  
Use the foam-removing spinning to  
Water inlet hose  
remove the extra detergent liquid. It  
can both shorten the washing time  
and save the water consumption.  
Spin water-filling  
entrance  
Foam-removing  
spinning  
Spin  
Fill water for  
about 1 minutes  
Spin for about  
1~2 minutes  
Remove most of  
the foam extra  
detergent liquid.  
Remove the detergent  
liquid remained  
When foam-removing spinning during  
high-efficiency rinsing, please fill water  
from the spin water-filling entrance.  
The effect is best when the  
laundries quantity is below  
80% of the rated value.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose .  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Pay attention to followings before washing the laundries  
Check if C l e a r t h e Tie the long The quantity of  
When the pulsator  
the laundries pocket. Take strips; fasten the laundries is running , the  
has special out the coins, the buttons; shall not be too buttons of the  
requirement sand, hairpins close zippers. large. Stretch laundries may  
on washing etc.  
and loosen the cause noise. For  
laundries before t h e s a k e o f  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like mud or dust.  
For the parts with heavy soil, please apply detergent on them in advance, which  
can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn it over before  
putting in.  
f. Do not put those laundries polluted by chemicals into the washing machine directly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
The musts in washing  
The capacity of washing and spinning of  
the machine refer to the largest weight of  
the standard laundries under dry condition  
that can be washed or spinned in one time.  
Laundries quantity in one washing cycle  
shall be lower than the rated capacity.  
The largest wash capacity of this mach-  
ine is 7.0kg. The largest spin capacity  
of this machine is 5.0 kg.  
The thickness ,size , type of the cloth will  
influence the actual washing capacity. It  
is suitable to put in reasonable amount of  
laundries and the laundries can be turned  
round in washing for one time washing.  
Do not select " Maximum " water level  
for laundries less than 3.2kg, so as to  
avoid splashing of water.  
Reference weight of the laundries  
Working suit up,down  
cotton,about 1120g  
Jeans about 800g  
Blanket  
cotton,about 900g  
Blending coat  
about 800g  
Pajamas  
Jacket  
cotton,about  
800g  
Shirt  
cotton,about  
300g  
Single bed sheet  
cotton,about 600g  
Undershirt  
cotton,about 180g  
Socking  
blending,about 50g  
Underpants  
cotton,about 70g  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Usage of the detergent  
How to use the whitener  
Fill water to decided level. Dilute the whitener with container. Pour it slowly into the  
washing tub.  
Avoid using whitener on laundries with color or pattern as they are prone to lose color.  
The whitener shall not touch the laundries directly.  
Refer to the user's manual for the usage and quantity of the whitener.  
For powder whitener, please dissolve it before using.  
How to use the washing powder  
Direct dissolved in the machine:  
1.Fill small quantity of water.  
2.Add the powder . Run for 30 seconds to  
dissolve it completely.  
3.Put it in the laundries. Select suitable  
water level.  
The powder is more prone to pollute the  
laundries than the detergent. Therefore  
please use it with proper quantity.  
It is suggested not to use high sudsing  
detergent.  
The instant dissolving of the washing powder:  
1.Prepare warm water of 30 C and a container.  
2.Add the powder while stirring to fully  
dissolve it.  
Dosage of different washing powder is  
different. Please refer to the instruction  
of the washing powder for the detail  
dosage.  
Selection of the quantity of the washing powder  
list 1  
Standard dosage  
Laundries  
quantity  
Water level  
Water quantity  
Concentrated washing  
powder  
Common washing  
powder  
Maximum (about43L)  
Medium (about36L)  
Minimum (about30L)  
About  
46g  
About  
4.5kg~7.0kg  
2.5kg~4.5kg  
Below2.5kg  
55g  
About  
38g  
About  
About  
46g  
36g  
About  
30g  
Selection of the current , water level and washing time list 2  
Washing time  
(minutes)  
Water level  
Water quantity  
Laundries  
quantity  
Laundries  
Knitwear  
About3~6  
About8~10  
About10~13  
About7~13  
About2~4  
About3~6  
About8~10  
Medium (about36L)  
~
Maximum (about43L)  
Cotton,blending,linen  
Very dirty and thick  
Bed sheet  
3.2kg~7.0kg  
Below3.2kg  
Silk(thin laundries)  
Chemical fiber  
Minimum (about30L)  
~
Medium (about43L)  
Cotton,blending,linen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Washing sequence  
Wash timer  
Wash selector  
(Strong current,  
standard current)  
Spin timer  
Spin water-filling entrance  
(To set to below 2 minute,  
first set to 5 minute then  
turn it back. it can increase  
the service life of the timer).  
(to set to below 1 minute,  
first set to 2 minute then  
turn it back. it can increase  
the service life of the timer).  
OFF  
OFF  
STRONG  
STANDARD  
DRAIN  
Spin water-filling entrance  
9
3
WASH SELECTOR  
WASH TIMER  
SPIN TIMER  
Wash  
1. Fill the water and add the dissolved washing  
powder to make the water level reach the preset  
position. (Figure 1)  
Run washing program for some time to stir and  
dissolve the powder completely.  
Figure 1  
2.Put in the laundries. If the water quantity is  
insufficient, please add water.  
STRONG  
STANDARD  
DRAIN  
WASH SELECTOR  
Figure 2  
3.Select the current.  
Select the strength of the current according to  
the laundries. (Figure 2)  
OFF  
4.Select the washing time  
Select the washing time according to the laundries.  
(Figure 2)  
Figure 3  
WASH TIMER  
STRONG  
STANDARD  
5.After washing, set the "WASH SELECTOR" at  
"DRAIN". (Figure 4).  
DRAIN  
Figure 4  
WASH SELECTOR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Midway spinning  
1.Put the laundries into the spin tub evenly and smoothly.  
2.Spin  
(1) Put the gland in properly.  
Please put in the gland properly even if the laundries quantity is small.  
Gland  
Push  
Push  
The laundries  
are slanting  
Proper  
Proper  
No gland  
(2) Close the inner and outer cover of the spin tub.  
Outer cover of  
The spin tub  
Inner cover of  
The spin tub  
(3) Spin for 1-2 minutes.  
3.Run the foam-removing spinning.  
Water inlet hose  
(1) Open the outer cover of the spin tub.  
(2) Insert the water inlet hose into the spin  
water-filling entrance on the control panel.  
Fill water for about 1 minute.  
Spin water-filling  
entrance  
(3) Close the outer cover of the spin tub.  
Spin for 1-2 minutes.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Rinsing  
Rinse with water-filing  
1.Put the laundries into the wash tub. Select  
suitable current according to the laundries.  
2.Adjust the water level  
Set the water level with water level adjusting  
lever according to the laundries quantity.  
Then fill suitable water continuously.  
3.Rinse  
Adjust the wash timer to 5-7 minutes to do  
rinsing.  
(Repeat the midway spinning and  
rinsing with stored water for 2-3 times)  
Rinse with stored water  
1. Put the laundries into the wash tub. Select suitable current according to  
the laundries.  
2. Fill water to preset water level.  
3. Rinse  
Adjust the wash timer to 2-3 minutes to do rinsing.  
When the laundries quantity is below 2.5kg, please use STANDARD current.  
If you use "STRONG" current, it may splash.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Spinning  
Selection of the spin time list 3  
1. Put the laundries into the spin tub  
evenly and smoothly.  
Spin time  
(minutes)  
Laundries  
Bed sheet or  
blanket  
2. Press the gland in the tub properly.  
Close the inner and outer cover of  
the spin tub.  
About 4~5  
About 2~4  
About 1~2  
Underwear  
(knitwear)  
Swear  
(chemical fiber)  
3. Spin  
Select suitable spin time according  
to the laundries, and do spinning.  
Blending thin  
laundries  
Within 1 minute  
During spinning, if there's abnormal  
sound, it is generally owing to slanting  
placement of the laundries. Please  
stop the machine and re-order the  
laundries.  
In spinning, it will pause the work if you open the outer cover of the spin  
tub. Close it to resume the spinning.  
To do spinning and draining or rinsing  
with water-filling together, please first  
do spinning for around 1 minute, then  
do draining or rinsing with water-filling.  
Otherwise the spinning will stop owing  
to too much water stored in the spin tub.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter and overflow filter  
in time. Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Cleaning the lint filter  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
1. Take off the lint filter  
Put hand at the indicated position.  
Push down to take it off. ( See to  
Figure 1)  
Figure 1  
2. Clean the lint  
Put it in water and clean while it is  
still wet.(See to Figure 2)  
Figure 2  
3. Install the lint filter  
After cleaning, insert the bottom  
of the lint filter ( marked with  
"DOWN SIDE") into the overflow filter ,  
then push the upper part of the  
filter in ( marked with " UP SIDE ").  
(See to Figure 3)  
Figure 3  
Cleaning the overflow filter  
Too much lint on the overflow filter will influence  
the normal usage of the machine. Please  
clean it every two months.  
1 Take off the overflow filter.  
As indicated in the figure, nip the elastic fixing  
claw and pull it to the direction of the arrow to  
take it off.  
Elastic fixing  
claw  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Cleaning the overflow filter  
2. Take off the corrugation pipe.  
Dismantle the upper part of the  
corrugation pipe inside the  
overflow filter ( as indicated in  
Figure 1).  
Water level  
adjusting lever  
Corrugation  
Pipe  
3. Cleaning the overflow filter  
Clean the lint around the filter  
and flush with tap water.  
Figure 1  
4. Install the overflow filter.  
(1).Install the corrugation pipe.  
(2).Insert the mounting plate at  
the bottom of the filter into  
original position.  
Hook  
(3).Hang up the hook at the left  
upper side.  
Figure 2  
(4).Push the upper part in as  
indicated in Figure 2.  
Disposal of the complete unit  
After washing, dismount the water inlet  
hose.  
Do not store water in the tub for long  
period. Discharge the water immediately  
after each using.  
Wipe the complete unit with soft cloth  
twisted dry.  
Wipe with neutral detergent if too dirty  
Do not wash it directly by water  
Pull off the power plug and hang up the  
power cord.  
Hang up the drain hose.  
Wipe off the water drops on the surface  
and inside the tub with clean soft cloth.  
Open the cover of the wash tub and the  
inner/outer cover of the spin tub for  
some time (about one hour), then close  
them.  
Petrol  
Thinner  
Alcohol  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble-shooting Answer to question  
If the laundries fall to the outer side of the spin tub  
If the laundries fall to the outer side of the spin tub,  
please take them out immediately.  
1.Dismantle  
As indicated in the figure, push the point marked  
with " " to pull the spin tub frame to oblique  
upwards to dismantle it.  
Spin tub frame  
2.Install  
After install the back edge of the spin tub frame to  
proper position, push the four points marked with  
" " by force to reset it.  
Spin tub  
Please check carefully. The laundries may fall to the lower part  
of the outer side of the spin tub (as indicated in the figure).  
If the laundries fall to the outer side of the spin tub, during  
spinning the draining will get blocked and the rotation speed  
of the spin tub is reduced.  
Laundries  
When the remained water is frozen  
Prevent the freezing (be sure to discharge the water completely after using)  
After complete draining, set the "WASH SELECTOR" at "STRONG" or "STANDARD".  
If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.  
Below 50  
When the water is frozen  
Pour hot water below 50  
into the wash tub  
to soak it completely. Then turn the pulsator  
with hands gently. Please confirm the drainage  
can work normally before next using.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble-shooting Answer to question  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending  
it to repair. If there are real breakdowns, please come to the special maintenance  
department or after-sale service department of our company. Do not repair it by yourself.  
Phenomena  
The reason  
Is there power failure?  
Is the power plug loose?  
Is the pulsator twisted by foreign materials?  
The machine does not act.  
Is the drain hose frozen?  
The draining does not work  
Is the drain hose blocked by foreign material?  
Are there laundries falling to the outer side of  
the spin tub?  
Is the drain hose put down?  
There's abnormal sound  
during washing  
Are there hair pin, coins or metal items brought  
inside the tub?  
There's abnormal sound  
and violent vibration  
during spinning  
Is the machine slanting?  
Is the gland pressed evenly?  
Are there laundries falling to the outer side of  
the spin tub?  
Are the laundries in spin tub too much?  
There may be some water  
flowing out of the drain  
hose in the first use of  
the machine.  
It is the water remained in the factory inspection  
of performance.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing list  
User's manual  
One piece  
Water inlet hose  
Water-filling jointer  
Gland  
One piece  
One piece  
One piece  
One piece  
Lint filter  
Twin-tub washing machine  
One set  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
Type  
Twin-tub washing machine  
Model  
WMS656  
Power source  
Rated voltage 220-240V~, Rated frequency 50Hz  
Water level Water quantity about  
Rated washing capacity kg  
Rated spinning capacity kg  
Rated input power W  
Dimension(mm)  
Maximum/43L Medium/36L Minimum/30L  
7.0  
5.0  
Wash 320 Spin 150  
L780 W440 H900  
New current  
Wash pattern  
Weight kg  
23.5  
Injection pressure  
0.02MPa~0.2MPa  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graham Field Pill Reminder Device 5717 1 EA User Manual
Guardian Technologies Vacuum Cleaner GGU350TT User Manual
Halo Lighting System Indoor Furnishings H2351 User Manual
Harbor Freight Tools Lathe 46407 User Manual
Hasselblad Camera Lens CF 8 500 User Manual
Havis Shields Automobile Accessories C 3311 18 2 User Manual
Healthrider Treadmill HRTL14980 User Manual
Heat Glo LifeStyle Indoor Fireplace SLR COSMO User Manual
Honeywell Humidifier HE265B User Manual
Hotpoint Dishwasher FDFSM 31011 FUTURA User Manual