Harbor Freight Tools Lathe 46407 User Manual

WOOD LATHE STAND  
Model 46407  
SET up AND OpErATiNg iNSTrucTiONS  
Designed for Harbor Freight Tools®  
Wood Lathe #36066  
Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
Distributed exclusively by Harbor Freight Tools®.  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE THiS MANuAL.  
Copyright© 2001 by Harbor Freight Tools®. All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions or replacement parts, please call 1-800-444-3353.  
cover revised 07i  
Download from Www.Somanuals.com. All Manuals Search And Download.  
plications for which this Lathe Stand was designed. Do not modify this Lathe  
Stand and do not use this tool for a purpose for which it was not intended.  
11. Stay alert. Watch what you are doing, use common sense. Do not use any  
Lathe Stand when you are tired.  
12. check for damaged parts. Before using any tool, any part that appears  
damaged should be carefully checked to determine that it will operate prop-  
erly and perform its intended function. Any part that is damaged should be  
properly repaired or replaced by a qualified technician.  
13. replacement parts and accessories. When servicing, use only identical  
replacement parts. Use of any other parts will void the warranty.  
14. Do not use Lathe with Stand if under the influence of alcohol or drugs.  
Read warning labels on prescriptions to determine if your judgment or re-  
flexes are impaired while taking drugs. If there is any doubt, do not use the  
Lathe with Stand.  
15. Take caution as some woods contain preservatives such as copper  
chromium arsenate (ccA) which can be toxic. When cutting these materi-  
als extra care should be taken to avoid inhalation and minimize skin contact.  
16. Maintenance. For your safety, maintenance should be performed regularly  
by a qualified technician.  
Warning: The warnings, cautions, and instructions discussed in this instruc-  
tion manual cannot cover all possible conditions and situations that may oc-  
cur. it must be understood by the operator that common sense and caution  
are factors which cannot be built into this product, but must be supplied by  
the operator.  
Warning! read and follow all of the warnings that came with the Lathe that  
you use with this stand.  
unpacking  
When unpacking, check to make sure the parts listed on page 5 are included. If  
any parts are missing or broken, please call Harbor Freight Tools at the number  
on the cover of this manual.  
SKU 46407  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
refer to the Assembly Drawing on page 6.  
Note: The only tool necessary is an adjustable wrench. It is advised to always  
tighten hardware by hand until the unit is complete, then tighten with the  
wrench.  
1. Take a Base plate (2) and attach a Leg A (3) to one side of it using four sets  
of Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10).  
2. On the opposite side of the Base plate (2), attach a Leg B (4) using a set of  
Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10).  
3. Repeat this procedure with the other Base plate (2) and Legs A&B (3&4) so  
that you have two identical leg structures.  
4. In the lowest holes of both Legs A&B (3&4) on one leg structure, attach a  
Leg Mounting A (5) so that the holes match up and the angled lip is on top.  
Secure with two sets of Bolts (7), Spring Washers (9), Flat Washers (8),  
and Nuts (10).  
5. Repeat same procedure with the other leg structure.  
6. Next, you will join the two leg structures allowing the unit to stand. Lay the  
units on a flat, level surface so that the insides of both leg structures are  
facing each other. Line up the two holes on a Leg Mounting B (6) with the  
holes on the inside of one of the Legs A&B (3&4). Secure it with two sets of  
Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10). Take the  
other end of the Leg Mounting B (6) bracket and attach it to the inside of  
the corresponding Leg A&B (3&4) on the other leg structure using two sets  
of Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10).  
7. Repeat the same procedure on the other two Legs A&B (3&4).  
8. Stand up the unit.  
9. Lastly, attach an Adapter plate (1) to each Base plate (2) using four sets of  
Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10).  
The stand is ready for your lathe.  
Operation  
Note: Always use the stand on a flat, level, dry surface. We recommend us-  
ing two people to secure the lathe to the Lathe Stand.  
1. When mounting a lathe onto the stand, first make sure the mounting holes  
on the stand correspond with the mounting holes on the lathe.  
2. One person should hold the lathe so that the mounting holes line up, while  
the other person puts one of the bolt, washer, nut combinations (not includ-  
ed) through one of the holes in an Adapter plate (1), and tighten by hand.  
Next, attach one bolt, washer, nut combinations (not included) through one  
of the holes on the other Adapter plate (1). Tighten by hand.  
3. Now, add the remaining hardware (not included) to secure all of the mount-  
ing holes, and tighten with a wrench.  
SKU 46407  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
1. Clean dirt, grease, or wood chippings off of the stand with a cloth or brush.  
2. Periodically tighten all of the hardware.  
parts List  
part  
1
Description  
Adapter Plate  
Base Plate  
Leg A  
Qty.  
2
2
2
3
2
4
Leg B  
2
5
Leg Mounting A  
Leg Mounting B  
Bolt  
2
6
2
7
24  
32  
32  
32  
8
Flat Washer  
Spring Washer  
Nut  
9
10  
pLEASE rEAD THE FOLLOWiNg cArEFuLLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM  
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER  
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO  
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PROD-  
UCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.  
IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT  
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTI-  
FIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES  
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL  
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER  
INSTALLATION OF REPLACEMENT PARTS THERETO.  
NOTE: Some parts are listed and shown for illustration purposes only and are not  
available individually as replacement parts.  
rEV 02b  
SKU 46407  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly Drawing  
SKU 46407  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Car Seat PD203828A User Manual
Greenheck Fan Ventilation Hood 471837 User Manual
Hasbro Games 03934 User Manual
Hasbro Stereo Amplifier OX4 User Manual
Huawei Cell Phone M865 User Manual
Hughes Kettner Stereo Amplifier Tube Amp Revolution User Manual
Hunter Fan Outdoor Ceiling Fan 21100 User Manual
Husqvarna Edger 322E 325E X User Manual
IBM Computer Drive 37L1388 User Manual
IBM Computer Hardware WD1003V MM1 User Manual