HP Hewlett Packard Projector xp7010 xp7030 User Manual
HP xp7010/xp7030 Series  
Digital Projector  
User’s Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
1 Setting Up  
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
What’s in the box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Identifying common features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Projector at a glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Projector buttons and lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Back panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Setting up the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Positioning the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Connecting power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Connecting a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Connecting a handheld organizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Connecting a video source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Turning the projector on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Turning the projector on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Turning the projector off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Moving the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Making basic adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Aiming the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Adjusting the focus and zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
2 Showing Presentations  
Showing a computer screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Selecting a different source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Hiding or showing the picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 Adjusting the Projector  
Adjusting the picture and sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Choosing the best picture mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Adjusting the shape of the picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Adjusting a slanted picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Adjusting the picture for best color. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Adjusting other picture settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Adjusting the sound settings (certain models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Adjusting the projector setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Preventing unauthorized use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Using the on-screen menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Changing settings using the on-screen menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Changing the default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Setup menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Picture menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Source menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Help menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
4 Maintaining the Projector  
Performing routine maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Getting the projector status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Cleaning the projector lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Replacing the lamp module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Replacing the battery in the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
Upgrading the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Updating the firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
5 Installing Permanently  
Installing the projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Choosing cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Installing on a table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Installing on the ceiling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Installing for rear projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Locking the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Controlling an external accessory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
Connecting to a room controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Serial connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Examples of room controller commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
Room controller commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
6 Fixing Problems  
Troubleshooting suggestions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Warning light problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Start-up problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56  
Picture problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56  
Sound problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59  
Interruption problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59  
Remote control problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
Testing the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
Running the projector diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
7 Reference  
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Mercury safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Regulatory information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65  
Japan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65  
Korea. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65  
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65  
Recycling information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Setting Up  
Safety precautions  
WARNING! Read and observe these precautions and all others in this manual to reduce the  
risk of injury and equipment damage.  
• Do not look directly into the lens when the lamp is on.  
• Do not expose the projector to rain or moisture, and do not use it near water.  
• Do not subject the projector to physical abuse or misuse such as exposure to smoke,  
unusual stresses, or excessive or continuous (24/7) operation.  
• Keep paper, plastic, and combustible material at least 0.5 m (2 ft) away from the  
projector’s lens and exhaust vents.  
• Do not allow liquid, food, or small objects to get inside the projector. If material gets inside  
the projector, contact HP for assistance.  
• Do not put anything on top of the projector. Do not place any liquids where they might spill  
on the projector.  
• Do not block any vents on the projector. Do not place the projector near any source of heat,  
such as a radiator or amplifier.  
• Use only an approved power cord rated for the voltage and current marked on the product  
label. Do not overload any outlet or extension cord. Do not circumvent the grounding prong  
on the power cord.  
• Route all cables so they are not located where people can step on them or trip on them.  
• Place the projector flat on its base on a sturdy surface or on an HP ceiling mount. Do not  
stand the projector on its front surface.  
• Do not touch the lens with your fingers. See “Cleaning the projector lens” on page 39. Use  
a soft, dry cloth to clean the projector case.  
• Do not open the projector except as instructed by this manual, and only after allowing the  
projector to cool down.  
• If the projector is damaged in any way, contact HP for assistance.  
6
Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
What’s in the box?  
Before setting up your projector, be sure its shipping box includes the following items. If the  
shipping box does not contain all of the following items, contact HP.  
TIP: After you open the box and remove the contents, save the box in case you must ship the  
projector.  
Identifying the contents of the box  
Item  
Function  
Projector  
Displays images.  
1
2
3
Quick Setup Guide  
Provides instructions to help get started.  
Literature package  
Contains documentation for the setup and use of the projector,  
plus support and warranty information.  
Remote control  
Power cord  
USB cable  
Controls the projector.  
4
5
6
7
Connects the projector to a power source.  
Connects the projector’s USB output to a computer.  
Connects a computer video output to the projector.  
VGA cable  
What’s in the box?  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Identifying common features  
Projector at a glance  
Identifying major components  
Item  
Function  
Adjustable foot  
Levels the projector (one foot on each rear corner).  
1
2
Disconnect switch  
Disconnects power. Turn off when unplugging the power cord.  
CAUTION: Do not use this switch to turn off the projector. Use the  
power button on top of the projector.  
Power cord socket  
Height adjustment button  
Lens  
Connects the power cord to the projector.  
Adjusts the height of the picture.  
Projects the image.  
3
4
5
6
7
8
Lens cap  
Protects the lens.  
Infrared port  
Receives signals from the remote control.  
Focus and zoom rings  
Focus ring: focuses at a distance of 1.2 to 10 m (4 to 33 ft).  
Zoom ring (with tab): enlarges the picture from 100% to 120%.  
Button panel  
Contains control buttons and indicator lights.  
9
8
Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Projector buttons and lights  
Identifying the projector buttons and lights  
Item  
Function  
Power button  
Turns the projector on or off.  
1
2
Page-up and Page-down buttons  
Lamp warning light  
Scrolls up and down through pages on a connected  
computer, or navigates the on-screen menu.  
Lit steady: the lamp is faulty.  
3
Flashing: the lamp ballast is faulty.  
Temperature warning light  
Source button  
Warns if the projector is too hot.  
4
5
Displays the picture from the next input port, or navigates the  
on-screen menu.  
Back button  
Exits the on-screen menu, or re-enters the on-screen menu at  
the most recently used item.  
6
Enter button  
Opens the on-screen menu or acts on the selected menu item.  
7
8
Picture mode button  
Selects the next picture and color combination—can be  
customized.  
Auto sync button  
Resynchronizes the projector to the input signal from a  
computer, or navigates the on-screen menu.  
9
Identifying common features  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Back panel  
Identifying back panel components  
Item  
Function  
Audio in and out ports  
Connect a stereo audio source using a stereo mini-phone  
plug, or an optional RCA-to-mini-phone plug.  
1
NOTE: Available only on certain models.  
USB port  
Connects to a computer and controls the mouse.  
2
3
4
Serial port  
DVI input port  
Connects a room controller.  
Connects a DVI-D digital video source.  
NOTE: Available only on certain models.  
VGA-in port  
Connects video input from a computer or component-video  
source.  
5
S-video input port  
Connects an S-video source.  
6
7
12-Vdc trigger output  
Controls a motorized screen or similar accessory device.  
NOTE: Available only on certain models.  
Infrared port  
Receives signals from the remote control.  
8
10 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Identifying back panel components (continued)  
Item  
Function  
Lock slot  
Locks the projector to a stationary object with the use of a  
cable and lock.  
9
Component video input port  
VGA-out port  
Connects a component video source.  
Sends the VGA-in signal to a monitor.  
:
;
<
Composite-video input port  
Connects a composite-video source.  
Remote control  
TIP: Before using the remote control, remove the battery protector by pulling the plastic tab  
until it comes out of the remote control.  
Identifying common features 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Identifying components of the remote control  
Item  
Function  
Hide button  
Blanks the picture, and mutes the audio (certain models only).  
1
2
3
4
Mouse pad  
Moves the mouse pointer on a connected computer.  
Turns the projector on or off.  
Power button  
Left-click and right-click mouse  
buttons  
Performs left-click and right-click mouse functions on a connected computer.  
Page-up and Page-down buttons Scrolls up and down through pages on a connected computer, or  
navigates the on-screen menu.  
5
6
Auto sync button  
Resynchronizes the projector to the input signal from a computer, or  
navigates the on-screen menu.  
Picture mode button  
Enter button  
Selects the next picture and color combination—can be customized.  
Opens the on-screen menu or acts on the selected menu item.  
7
8
9
Back button  
Exits the on-screen menu, or re-enters the on-screen menu at the most  
recently used item.  
Source button  
Displays the picture from the next input port, or navigates the on-screen  
menu.  
:
Accessories  
Get more from your presentations with HP projector accessories. You can purchase accessories  
at http://www.hp.com or through your projector dealer.  
• HP ceiling mount kit—enables you to simply and discreetly install your projector on the  
ceiling.  
• HP projection screens—mobile screens that are easy to carry and set up anywhere, and  
fixed screens for even greater convenience.  
• HP premium remote control—allows you to control every aspect of your presentations.  
• HP power cables—allow you to connect in any region.  
• HP cables—allow you to connect all audio-video equipment.  
• HP replacement lamp—brings your projector up to factory-fresh brightness.  
• HP pn1050 Jetdirect projector server—enables you to connect your projector directly to a  
network, and manage it from anywhere on the network.  
• HP projector carrying case—enables you to transport your projector safely.  
• HP SCART to composite S-video adapter—allows you to connect SCART devices.  
12 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Setting up the projector  
Positioning the projector  
The following tables show you where to position the projector in relation to the screen.  
TIP: For more information on adjusting the picture, see “Making basic adjustments” on  
page 25 and “Adjusting the Projector” on page 29.  
Setting up the projector 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Image size relative to distance from the screen — xp7010/xp7030 series  
Image size (diagonal) Image size (width) Distance — Tele (lens to screen)  
(inches)  
40  
(meters)  
(inches)  
32  
(meters)  
(inches)  
(meters)  
1.0  
1.3  
1.5  
2.0  
2.5  
3.8  
5.1  
6.4  
0.8  
1.0  
1.2  
1.6  
2.0  
3.0  
4.1  
5.1  
52 to 63  
1.3 to 1.6  
1.7 to 2.0  
2.0 to 2.4  
2.7 to 3.2  
3.3 to 4.0  
5.0 to 6.0  
6.7 to 8.0  
8.3 to 10.0  
50  
40  
65 to 79  
60  
48  
79 to 94  
80  
64  
105 to 126  
131 to 157  
197 to 236  
262 to 315  
328 to 394  
100  
150  
200  
250  
80  
120  
160  
200  
If you do not want to use the distance table, you can use the following equations to help  
determine where to install the projector relative to the screen.  
Calculating projection distances  
distance from lens to screen = A × width of screen  
minimum and maximum distance from screen = B  
width of screen = 0.8 × diagonal of screen (for 4:3 screen)  
projector lens below bottom of screen = C × width of screen (for 4:3 screen, with projector sitting level)  
xp7010/xp7030 series  
A = 1.6 to 2.0  
B = 1.2 to 10 m (4 to 33 ft)  
C = 0.12  
14 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connecting power  
1. Place the projector on a stable platform located 1.2 to 10 m (4 to 33 ft) in front of the  
screen. Ideally, the platform should be lower than the bottom of the screen.  
2. Connect one end of the power cord to the back of the projector 1 and the other end to a  
grounded electrical outlet 2.  
3. Turn on the disconnect switch 3 on the side of the projector.  
If you want to permanently install the projector on the ceiling or behind the screen, see  
“Installing the projector” on page 44.  
Setting up the projector 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Connecting a computer  
Requires:  
• VGA cable or other video source cable 1  
• USB cable 2 (optional)  
• Audio cable, mini-phone (optional)  
The optional USB connection allows you to use the mouse and page up/down features on the  
remote control.  
See “Showing a computer screen” on page 28.  
TIP: If the computer display does not appear on the projector, you might have to press a  
combination of keys on the computer to turn on the computer’s VGA output. For example, on  
some computers you must press FN+F4 or FN+F5. For instructions, refer to the user  
documentation provided with your computer.  
TIP: You can connect an external computer monitor to the VGA-out port on the projector. The  
monitor displays the signal connected to the VGA-in port—even if the projector is turned off or  
showing a different input.  
16 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Connecting a handheld organizer  
Not all handhelds come with VGA-out ports. For example, an iPAQ Pocket PC may require a  
VGA-out PC Card with 15-pin connector. If necessary, install a VGA-out accessory card into  
the organizer.  
Requires:  
• VGA cable 1  
• VGA-out accessory card 2 (in some cases)  
Setting up the projector 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Connecting a video source  
Many video devices have more than one type of output port. When you connect the device to  
the projector, choose the connection that provides the best picture quality. This list shows video  
connections in order with highest picture quality at the top:  
• DVI connection (highest quality)  
• Component-video connection  
• S-video connection  
• Composite-video connection  
The video and audio cables shown in the following sections are available from HP.  
If you want to connect a SCART video device to the projector, you will need a SCART adapter  
(available from HP).  
Connecting a DVI source  
The DVI port is available only on certain models. It supports only DVI digital sources.  
Examples: Cable boxes, satellite receivers, and some computers  
Requires:  
• DVI-D cable 1  
• Audio cable, mini-phone 2 (optional)  
18 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Connecting a component-video source with a component-to-VGA  
cable  
Examples: Cable boxes, DVD players, satellite receivers, and audio-video receivers  
Requires:  
• Component-to-VGA cable 1  
• Audio cable, mini-phone 2 (optional)  
TIP: Many DVD players and other high-quality video devices provide component video output  
through three RCA connectors (which might be labeled YPbPr or YCbCr). Connect the  
component-to-VGA cable to the video device’s RCA connectors and the projector’s VGA-in  
port.  
If possible, configure the video source to use progressive scan output, such as 480p, 575p,  
or 720p. For additional information, refer to the user documentation provided with the video  
source.  
Setting up the projector 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connecting an RCA component-video source (certain models only)  
Examples: Cable boxes, DVD players, satellite receivers, and audio-video receivers  
Requires:  
• Standard component-video cable 1  
• Audio cable, mini-phone 2 (optional)  
TIP: Many DVD players and other high-quality video devices provide component video  
output. The three RCA connectors might be labeled YPbPr or YCbCr.  
If possible, configure the video source to use progressive scan output, such as 480p, 575p,  
or 720p. For additional information, refer to the user documentation provided with the video  
source.  
20 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connecting an S-video source  
Examples: DVD players, VCRs, cable boxes, camcorders, and video gaming devices  
Requires:  
• S-video cable 1  
• Audio cable, mini-phone 2 (optional)  
Setting up the projector 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connecting a composite-video source  
Examples: VCRs, DVD players, audio-video receivers, and video gaming devices  
Requires:  
• Composite-video cable 1  
• Audio cable, mini-phone 2, or combined video-audio cable (optional)  
22 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Turning the projector on and off  
Turning the projector on  
1. Be sure the power cord is connected and the disconnect switch is on.  
2. Remove the lens cover 1.  
3. Press the power button 2 on the projector or on the remote control.  
The projector takes a minute or so to warm up. The power button blinks during warm-up.  
TIP: If the picture does not appear on the screen, try the following:  
• If you are using a computer, press the key combination that turns on its video output. For  
example, press FN+F4 or FN+F5 on some computers.  
• On the projector, press the source button one or more times to select the correct input port.  
NOTE: It is normal for parts of the projector and the air coming out of the projector to be very  
warm. If the projector starts to overheat, the temperature warning light will turn on and the  
projector will shut down.  
Turning the projector on and off 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Turning the projector off  
1. Press the power button on the projector or remote control to turn off the projector. Do not  
hold the button down.  
The power button blinks during the cool-down period, then the projector turns off. Even  
though the projector is off, it uses a small amount of power internally.  
2. If you want, disconnect video and audio equipment from the projector during the cool-  
down period or after the power button stops blinking.  
CAUTION: Do not disconnect power or turn off the disconnect switch until the projector has  
cooled down (the fan stops) and the power button stops blinking. Otherwise, you might shorten  
the life of the lamp.  
3. If you must unplug or remove the projector, wait until the power light stops blinking, then  
unplug the power cord.  
If you try to turn on the projector again during the cool-down period, it will not turn on. Wait  
until the cool-down period ends and the power button stops blinking.  
Moving the projector  
When moving the projector:  
• Allow the projector to cool down before moving it. Then disconnect all cables.  
• Avoid bumps and jolts. Use a carrying case or padded container when possible.  
• Observe temperature and humidity limits (see “Specifications” on page 61). If the projector  
is cold, allow it to warm gradually to avoid condensation.  
24 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Making basic adjustments  
This section provides instructions for making basic adjustments to the projector.  
Aiming the projector  
• To raise or lower the projected picture on the screen, press the height adjustment button 1  
and raise or lower the front of the projector 2. Release the button to lock the adjustment.  
• To level the picture on the screen, turn the adjustable feet 3 to lengthen or shorten.  
Adjusting the focus and zoom  
• Rotate the focus ring until the image becomes clear. The projector can be focused at  
distances of 1.2 to 10 m (4 to 33 ft).  
• Rotate the zoom ring (with tab) to adjust the picture size (100% to 120%).  
If the picture does not fit the screen, you might have to move the projector closer to or farther  
away from the screen.  
TIP: For more information on adjusting the picture, see “Adjusting the Projector” on page 29.  
Making basic adjustments 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Using the remote control  
To do this...  
Press this...  
Hide or unhide the picture, and mute or unmute  
the audio (certain models only)  
hide button 1.  
Move mouse pointer on computer  
Edge of the mouse pad 2 in the direction you  
want the pointer to move. This feature requires a  
USB connection between the projector and  
computer.  
Turn the projector on or off  
Power button 3.  
Click mouse button on computer  
Left-click or right-click button 4. This feature  
requires a USB connection between the projector  
and computer.  
Page up or page down on computer  
Readjust picture of computer screen  
Page-up or page-down button 5. This feature  
requires a USB connection between the projector  
and computer.  
auto sync button 6.  
26 Setting Up  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
To do this...  
Press this...  
Change picture settings for different type of input Picture mode button 7 one or more times.  
signal  
Change settings using on-screen menu  
enter and navigation buttons 8. See “Using the  
on-screen menu” on page 34.  
Exit from any on-screen menu or adjustment  
Switch to next input source  
Exit  
button 8.  
source button 9 one or more times.  
TIP: From within the distance of 8 m (26 ft), aim the remote control at the screen or at the front  
or back of the projector.  
Using the remote control 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 Showing Presentations  
Showing a computer screen  
1. Be sure the computer is connected to the projector and turned on. See “Connecting a  
computer” on page 16.  
2. Be sure the projector is set up, turned on, and adjusted. See “Making basic adjustments”  
on page 25.  
3. If a different input source is shown on the projector, press the source button on the projector  
or remote control one or more times to select the VGA-in port.  
4. If the computer display is not shown on the projector, you might have to turn on the  
computer’s video output port. For example, some computers require you to press a key  
combination, such as FN+F4 or FN+F5. Refer to the user documentation provided with your  
computer.  
If you want to adjust the picture, see “Adjusting the picture and sound” on page 29.  
Selecting a different source  
If the picture from your video source does not appear on the screen, you can quickly select the  
correct source.  
S Press the source button one or more times—until you see the picture or you see the name of  
the video port where the source is connected.  
You should also be sure the video source is turned on and playing video.  
Hiding or showing the picture  
1. Press the hide button on the remote control to blank the picture, and to mute the audio  
(certain models only). This does not affect the video source, which continues playing.  
2. Press any button to restore the picture, as well as the audio (certain models only).  
28 Showing Presentations  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
3 Adjusting the Projector  
You can change the projector’s settings through its built-in on-screen menu system, using the  
buttons on the projector or the remote control.  
To access the on-screen menu, press enter on the projector or remote control.  
For details, see “Using the on-screen menu” on page 38.  
Adjusting the picture and sound  
Choosing the best picture mode  
You can quickly choose a different picture mode to make adjustments to the picture. Picture  
modes can control properties such as color and size. They let you easily choose the best  
settings for ambient lighting and the type of video content.  
S Press the picture mode  
button one or more times to select the picture mode that gives the  
best picture.  
Adjusting the picture and sound 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
You can also customize the picture modes so they are best for your video sources:  
1. Press the picture mode button to select the picture mode you want to adjust.  
2. Press enter and go to Picture > Customize picture mode.  
3. Adjust the settings until you are satisfied with the picture.  
TIP: To exit from any on-screen menu or adjustment, press the exit  
button.  
To return to the most recently used menu item when no on-screen menu or adjustment is  
displayed, press the exit button.  
Adjusting the shape of the picture  
Depending on the type of video source you are viewing, the picture might or might not always  
look correct or fit on the screen:  
• If the active video device sends widescreen output to the projector, press enter, go to  
Source, and set Widescreen input to On. See 1 in the following diagram.  
• If the video device sends standard output, set Widescreen input to Off.  
TIP: If you show widescreen pictures on a wide projection screen, a standard picture might  
not fit on the screen. One solution is to change the current picture mode so it makes a smaller  
picture. Press enter, go to Picture > Customize picture mode, and set Aspect Ratio to Reduced.  
See 2 in the following diagram.  
30 Adjusting the Projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Adjusting a slanted picture  
If the projector is tilted up or down, the sides of the picture on the screen might slant in or out,  
even though the top and bottom are level. The keystone adjustment corrects this problem.  
Adjust the picture using the keystone setting in the on-screen menu. Press enter, go to Setup >  
Keystone, and adjust until the picture looks correct.  
TIP: If the projector is not perpendicular to the screen, the projected image may slant left or  
right. If this happens, turn the projector until the image is rectangular, with straight corners.  
Adjusting the picture and sound 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Adjusting the picture for best color  
You can fine tune the picture settings on your projector to get the best color and image quality.  
You should perform these steps for each input source device and each input port that you use.  
Do them in the order shown. For some input ports, some of these settings may not be available.  
1. Press the picture mode  
button and select the picture mode you want to use for the current  
source.  
2. Press enter and go to the Picture menu.  
3. Go to Color settings > Brightness. Adjust to the highest setting that still gives the darkest  
black for black areas.  
4. Go to Color settings > Contrast. Adjust to the highest setting that does not wash out fine  
detail in bright areas. You can view bright clouds or textured white areas.  
5. Go to Customize picture mode > Picture enhancement. Adjust to the setting that gives the  
best overall mid-range brightness. This should have minimal effect on blacks and whites.  
6. Go to Customize picture mode > Color temperature. Adjust to the setting where whites and  
colors look best.  
7. Go to Color settings > Color saturation. Adjust to the setting where colors look most  
natural.  
8. Go to Color settings > Tint. Adjust to the setting where colors look most natural.  
9. Go to Advanced Color. Adjust Red, Green, and Blue to the settings where the colors  
appear most natural.  
10. Go to Customize picture mode > White intensity. Adjust this setting above 0 as needed to  
brighten the picture. Note that color accuracy drops as white intensity increases.  
11. Repeat all steps if necessary.  
Adjusting other picture settings  
The on-screen menu provides many settings that allow you to fine-tune the picture.  
1. Press enter, and go to Picture.  
2. Change the picture adjustments as needed.  
From the Picture menu, you can change many picture options, such as brightness, contrast,  
and picture shape, as well as customize the picture modes.  
To get descriptions for all available picture adjustments, see “Picture menu” on page 36.  
32 Adjusting the Projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Adjusting the sound settings (certain models only)  
You can control the volume of the projector’s speaker or any connected speakers:  
• To change the volume, press enter, go to Setup > Volume, and change the setting.  
• To turn the sound on or off temporarily, press enter, go to Setup > Mute, and mute the  
sound.  
Adjusting the projector setup  
1. Press enter, and go to Setup.  
2. Set the setup adjustments as needed.  
From the Setup menu, you can select settings, such as menu language, projector position,  
and menu timeout.  
To get descriptions for all available setup adjustments, see “Setup menu” on page 35.  
Preventing unauthorized use  
You can prevent unauthorized people from using the projector by creating a secret button  
sequence that is required for the projector to turn on. The unlock sequence is a series of 4 to 8  
arrow buttons. If the buttons are not pressed in the order you specify, the projector does not  
turn on. Use the following steps to set or clear an unlock sequence.  
1. Press enter, go to Setup > Advanced setup > Projector lock, and press enter.  
2. If an old unlock sequence is set, press the buttons according to the old sequence when  
prompted, and then press enter.  
3. To set a new unlock sequence, press the arrow buttons for the new sequence, and then  
press enter.  
To clear the unlock sequence and remove this protection, press only enter.  
4. When prompted, confirm the new sequence and press enter.  
NOTE: If you set an unlock sequence, you must press the sequence every time you turn on the  
projector. The sequence protects the projector only when the projector is turning on, not at any  
other time.  
If you forget the unlock sequence, you must call HP support to unlock the projector. You must  
have the projector and your proof of purchase.  
Adjusting the picture and sound 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Using the on-screen menu  
Changing settings using the on-screen menu  
You can change the on-screen menu settings with the buttons on either the projector or the  
remote control.  
1. Press enter on the projector or remote control. This displays the on-screen menu.  
2. Press up  
or down  
to highlight the desired menu icon, then press right to move into  
that menu.  
3. Press up  
or down  
to highlight a setting, then press enter to begin adjusting the  
setting.  
4. Press left or right , or press up  
5. Press enter to return to the menu.  
or down , to adjust the setting, as prompted.  
6. To go to a different menu, press left and select a menu.  
7. To close the on-screen menu, press the exit button.  
If you do nothing for a period of time, the on-screen menu closes. To change the amount of  
time until the on-screen menu closes, press enter and select Setup > Timeout for menu.  
TIP: To exit from any on-screen menu or adjustment, press the exit  
button.  
Changing the default settings  
The on-screen menus enable you to return selected or all projector settings to saved default  
values. These values are originally the factory defaults, but you may prefer to replace the  
factory defaults with a custom set of your own, using the following procedure. (You can also  
restore the original factory defaults if needed.)  
NOTE: This procedure will normally be performed by a system administrator.  
1. Press enter on the projector or remote control. This displays the on-screen menu.  
2. Use the on-screen menus to select the desired settings for all inputs and picture modes.  
3. Select Help > Diagnostics....  
4. On the remote or the projector, press the up and down buttons in this sequence to open the  
default settings menu:  
up – up – down – down – up – down (  
5. Press enter to save the projector’s current settings as the new defaults. (You can also press  
the exit button to restore the original factory default settings.)  
)
34 Adjusting the Projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Setup menu  
Setup menu  
Keystone  
Corrects the slanted sides of the picture. This compensates for a projector  
that is too high or low relative to the screen.  
Reset keystone  
Volume  
Resets the keystone correction to zero (no correction).  
Adjusts the loudness of the projector’s audio (certain models only).  
Temporarily turns off the projector’s audio (certain models only).  
Mute  
Projector position  
Adjusts the picture to match the orientation of the projector: upright or  
upside-down, in front of or behind the screen. Inverts or reverses the image  
accordingly.  
Lamp saver  
Language...  
Hide  
Sets a lower power level for the lamp.  
Selects the language used by the on-screen menu.  
Hides the picture and mutes the sound.  
Adjusts additional setup settings.  
Advanced setup...  
Power timeout  
Sets the length of time the projector waits for an input signal before  
automatically shutting down.  
Clean edges  
Enlarges and clips video images to remove noise from picture edges.  
Sets how many seconds the on-screen menu waits for input before it closes.  
Fine-tunes the width of the image for multi-projector setups.  
For a new lamp, resets the hours of use.  
Timeout for menu  
Horizontal size  
Reset lamp hours  
Projector lock...  
Sets or cancels a secret button sequence that must be entered for the  
projector to operate.  
Reset all settings  
Restores all menu settings to factory default settings.  
Using the on-screen menu 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Picture menu  
Changing these settings affects only the active source. Some picture adjustments are available  
only when certain input ports are in use. Unavailable adjustments are shown in gray in the on-  
screen menu.  
Picture menu  
Color settings...  
Brightness  
Contrast  
Adjusts the picture and colors.  
Brightens or darkens the picture.  
Sets the difference between light and dark areas.  
Sharpens or softens the picture.  
Sharpness  
Color saturation  
Tint  
Adjusts the intensity of colors.  
Shifts colors toward red or green.  
Reset color settings  
Advanced color...  
Red  
Restores these color settings to the default settings.  
Adjusts the individual colors in the picture.  
Adjusts the amount of red in the picture.  
Adjusts the amount of green in the picture.  
Adjusts the amount of blue in the picture.  
Restores the advanced color settings to their default values.  
Green  
Blue  
Reset advanced  
settings  
36 Adjusting the Projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Picture menu (continued)  
VGA settings...  
Adjusts settings for a computer input.  
Auto-sync  
Resynchronizes the projector with the input. If a VGA input image looks  
incorrect, press auto-sync to try correcting the image.  
Frequency  
Tracking  
Adjusts the timing of the projector relative to the computer.  
Adjusts the phase of the projector relative to the computer.  
Adjusts the picture up or down within the projection area.  
Adjusts the picture left or right within the projection area.  
Vertical offset  
Horizontal offset  
Picture mode  
Adjusts color and picture settings to one of several combinations designed  
for different types of viewing situations. You can use a different picture  
mode for each source or each viewing environment. You can also customize  
each picture mode.  
Customize picture mode... Changes settings associated with the current picture mode.  
Picture enhancement  
White intensity  
Color temperature  
Aspect ratio  
Refines the color, lightness, and other characteristics of the picture.  
Increases the brightness of white areas.  
Shifts color toward red or blue.  
Selects how the picture fits on the screen:  
•
•
•
Best fit automatically fits the picture without stretching it.  
1-to-1 shows each picture dot as one projected dot.  
Reduced fits a standard-shape picture onto a widescreen projection  
screen.  
•
Full uses the entire projector resolution screen size, with stretching  
permitted.  
Reset this picture mode Restores the current picture mode to its default settings.  
Using the on-screen menu 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Source menu  
For a visual aid, see “Back panel” on page 10.  
Source menu  
VGA  
Shows the source connected to the VGA-in port.  
Shows the source connected to the composite-video port.  
Shows the source connected to the S-video port.  
Composite video  
S-video  
Component  
Shows the source connected to the component video port (available only on  
certain models).  
DVI  
Shows the source connected to the DVI port (available only on certain models).  
Source scan  
Sets whether the projector automatically searches for input signals and displays  
the next one found.  
Widescreen input  
Sets whether a widescreen (16:9) input device is in use. Adjusts the height of the  
picture accordingly.  
Help menu  
Help  
Displays information and status of the projector.  
Diagnostics...  
Show tests for checking the operation of the projector and the remote  
control.  
HP digital projector  
Displays information about the projector and any network connection.  
38 Adjusting the Projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4 Maintaining the Projector  
Performing routine maintenance  
Getting the projector status  
To get the projector status:  
S Press the enter button on the projector or remote control and go to Help.  
This screen shows information and status for the projector.  
Cleaning the projector lens  
You can clean the front lens of the projector using the following recommendations. You cannot  
clean any of the internal surfaces.  
• To minimize the risk of damaging or scratching the lens surface, blow dust particles off the  
lens with clean, dry, deionized air.  
• If this method does not work, use the following method:  
a. Wipe the lens in a single direction with a clean, dry cloth. Do not wipe back and forth  
across the lens.  
b. If the cloth is dirty or smears the lens, wash the cloth. If the cloth is still dirty after  
washing it or the fabric is damaged, replace it.  
CAUTION: Cleaning requires special consideration:  
• Do not spray any type of fluid or cleaner directly on the lens surface. Cleaners might  
damage the lens.  
• Do not use fabric softener when washing a cleaning cloth or softener sheets when drying  
the cloth. Chemicals on the cloth might damage the surface of the lens.  
• Do not store a cleaning cloth in contact with the lens for a long time because doing so  
contaminates the lens with dye from the cloth. The cloth can be contaminated if left in the  
open air.  
Performing routine maintenance 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Replacing the lamp module  
As the projector operates over time, the brightness of the projector lamp gradually decreases  
and the lamp becomes more susceptible to breakage. You can install a new lamp at any time  
to bring the projector up to factory-fresh brightness. We recommend replacing the lamp if a  
warning message is displayed.  
WARNING! Replacing the lamp module requires special consideration:  
• To reduce the risk of injury, be careful when removing the lamp module as broken glass  
might be present. HP also recommends wearing goggles and gloves when removing the  
lamp module. If the lamp is broken, contact HP about repairs that might be required due to  
glass fragments.  
• The lamp in this digital projector contains mercury. If the lamp breaks, adequately ventilate  
the immediate area, discard any nearby food and drink, and thoroughly clean the table  
surface around the projector. Wash your hands after cleaning the area or handling a  
broken lamp. Note that disposal of this lamp may be regulated under applicable  
environmental laws due to presence of mercury. For disposal or recycling information,  
please contact your local authorities or the Electronic Industries Alliance (www.eiae.org).  
For additional safety information about the lamp in this digital projector, please see:  
www.hp.com/hpinfo/globalcitizenship/environment/productdata  
• Because the lamp assembly operates at a very high temperature, wait 30 minutes before  
removing the lamp module.  
1. Turn off the projector and allow it to cool for 30 minutes.  
2. If the projector is installed in a ceiling mount, remove it from the mount.  
3. Unplug the power cord.  
40 Maintaining the Projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4. Loosen the two screws in the lamp cover 1 and remove the cover 2.  
5. Remove the two screws 3 from the lamp module, raise the handle 4, and lift out the  
module 5.  
6. Insert the new lamp module into the projector and tighten the two screws.  
7. Replace the lamp cover and tighten the two screws.  
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling  
the lamp.  
9. Press enter, go to Setup > Advanced setup > Reset lamp hours, and press enter.  
Performing routine maintenance 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing the battery in the remote control  
1. Use a ballpoint pen to hold the battery latch toward the center, then pull out the battery  
holder 1.  
2. Insert the new battery 2 in the holder.  
3. Push the holder 3 into the remote control.  
When discarding old batteries, contact your local waste-disposal provider regarding local  
restrictions on the disposal or recycling of batteries.  
42 Maintaining the Projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Upgrading the projector  
Updating the firmware  
HP might periodically release updated versions of the projector firmware to enhance the  
projector performance. The projector firmware version is shown in the on-screen menu at Help.  
Check for updated versions at http://www.hp.com/support.  
USB method  
1. On a computer with a USB port, go to the HP projector upgrade website (see introduction  
for this section) and download the latest file intended for the xp7010/xp7030 series  
projector.  
2. Connect a USB cable (available from HP) to the USB port on the computer. Do not connect  
the cable to the projector at this point.  
3. On the computer, run the file you downloaded by double-clicking the file.  
4. Follow the on-screen instructions. When prompted, connect the USB cable to the projector.  
NOTE: Be sure to follow the “new hardware found” instructions exactly as shown on-screen,  
or the firmware will not be updated.  
Upgrading the projector 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
5 Installing Permanently  
Installing the projector  
Choosing cables  
If you are permanently installing the projector or using it with long cables, consider the  
following suggestions when planning the installation:  
• Use high-quality cables. Use only video cables that are made with 75-ohm cable and  
connectors. For high-resolution video, use low-loss video cables. For standard audio, use  
audio cables that are shielded.  
• Minimize cable length as much as possible. For video cables longer than 6 m (20 ft), use  
low-loss cables. For standard audio cables longer than 6 m (20 ft), use 12-gauge wire.  
• Do not run audio or video cables next to power or network cables. If they must cross, cross  
them at 90 degrees.  
• If you are installing cables in walls, use cables with necessary approvals, such as  
Underwriters Laboratories (UL) approval.  
• If you are running cables above a dropped ceiling, you must use plenum-rated cables if the  
space above the ceiling is open to the space above other rooms. You must use plenum-  
rated cables if you are running cables in a duct.  
• Before installing cables permanently, check the setup with the final cables in the open.  
Installing on a table  
This installation is covered in detail in Chapter 1. See “Setting up the projector,” for more  
information.  
44 Installing Permanently  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Installing on the ceiling  
WARNING! To minimize the risk of injury from improperly installed equipment, it is  
recommended that a professional installer performs the ceiling installation.  
1. Attach the projector to the ceiling using an HP ceiling mount kit. Refer to the installation  
instructions provided with the ceiling mount kit.  
2. After the projector is mounted on the ceiling, adjust the projector settings to match this  
setup. Press enter, go to Setup > Projector position, and select Front Ceiling.  
Installing for rear projection  
1. Place the projector 1.2 to 10 m (4 to 33 ft) behind a translucent screen that is designed for  
rear projection.  
See “Setting up the projector,” or “Installing on the ceiling,” above, for more instructions.  
2. Press enter, go to Setup > Projector position. Then select Rear Table or Rear Ceiling.  
Locking the projector  
The projector includes a built in slot to secure the projector with a cable and lock (such as the  
Kensington MicroSaver lock system, available at many computer stores).  
1. Wrap the cable around a secure object, such as a table leg. Loop the cable to create a slip  
knot around the stationary object, and be sure it cannot slip off.  
2. Insert the lock 1 into the hole and twist the key 2.  
Installing the projector 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Controlling an external accessory  
If your projector has a 12-volt trigger output port, the projector can automatically control one  
or more accessories. Certain types of accessories can use a 12-volt signal to trigger their  
actions, such as a motorized screen lowering and raising the screen. The output provides a  
12-volt dc signal whenever the projector is on (200 mA maximum current output).  
Requires:  
• Two-wire cable with 3.5-mm × 1.3-mm barrel connector (+12 V on inner contact) with the  
following specifications.  
+12V output electrical specification  
Parameter  
Value  
Output voltage  
12 +/- 10% V  
0.1 Vpp  
200 mA  
2.0 A  
Output ripple  
Maximum output current  
Maximum rush current  
Maximum rush current duration  
10 ms  
46 Installing Permanently  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Connecting to a room controller  
If your projector has a serial port, you can connect the projector to a room controller using a  
serial (RS-232) cable. After you program the room controller using the following commands,  
you can use the room controller to operate the projector and other components of your  
installation.  
Serial connections  
The serial port on the projector uses a female, mini-DIN 6, RS-232 connector:  
• Pin 3: data sent to the projector (RX)  
• Pin 5: data sent from the projector (TX)  
• Pins 1, 4, and 6: not connected  
• Pin 2: ground (GND)  
• 7: metal frame (shroud)  
The room controller must use the following serial (RS-232) settings:  
• 9600 baud  
• 1 start bit + 8 data bits (D0=LSB, D7=MSB) + 1 stop bit  
• No parity  
• Full duplex communication channels (no flow control)  
• No handshaking  
TIP: Go to http://www.hp.com/support for additional information.  
Connecting to a room controller 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Examples of room controller commands  
In the following examples, “<CR>” and “<LF>” represent a carriage return and line feed,  
respectively.  
Commands are sent to the projector as “requests” which consist of an asterisk (*) prefix, the  
command name, any needed parameter, and a carriage return <CR> as a terminator:  
* command = parameter <CR>  
Requests can contain only ASCII alphanumeric characters. Blanks (spaces) are allowed, except  
within keywords and numbers. Line feeds <LF> are ignored.  
The following table shows the specific syntax to use for various requested tasks.  
To perform this task...  
Use this request syntax...  
*command=value<CR>  
*command=?<CR>  
*command=+<CR>  
*command=–<CR>  
*command<CR>  
Change a setting to a specified value  
Ask the current setting  
Increment a setting  
Decrement a setting  
Invoke an action (no parameter needed)  
In general, every request sent to the projector generates one or more notification messages,  
which are sent to the room controller. Actions initiated by the projector can also generate  
notifications.  
The projector always sends notifications whenever a setting changes, whether as the result of a  
request from a controller, or as the result of an action, such as a button press or menu change.  
Some requested setting changes take time to perform, or are carried out in stages. Because of  
this, requests might produce delayed notifications.  
48 Installing Permanently  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The following table lists the types of notifications generated in various situations.  
This type of request...  
Generates this type of notification...  
Modify a setting  
Echoes the request command and shows the resulting value:  
Request: *BRT=65<CR>  
Notification: *BRT=65<CR><LF>  
Query a setting  
Echoes the request command and shows the resulting value:  
Request: *CON=?<CR>  
Notification: *CON=40<CR><LF>  
Execute an action  
Echoes the request command:  
Request: *NXT<CR>  
Notification: *NXT<CR><LF>  
Incorrect commands cause the following types of notifications:  
• No asterisk at start of command—no response  
• Unrecognized command name—command with “?” added  
• Command that is currently unavailable—command with “?” added  
• Invalid parameter—command with current value  
• Action command with unnecessary parameter—action command  
• Action command that is unavailable—action command  
The following simplified example shows how the projector typically responds to a request to  
change the active input source. Note that the three latter notifications are delayed.  
Request:  
*RSRC=4<CR>  
Notification:  
*RSRC=4<CR><LF> (acknowledges request)  
*SRC=0<CR><LF>  
(projector is attempting to acquire source 4, and in the interim  
has no valid source)  
*SRC=4<CR><LF>  
(source 4 is now active)  
*BRT=60<CR><LF> (brightness has been modified for source 4)  
*CSPC=?<CR><LF> (color space is not supported for this input)  
Connecting to a room controller 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Room controller commands  
In the following tables, if the parameter listing for a particular command is “None,” that  
command requires no parameter. Some commands are valid only when the projector is turned  
on, STAT=1. Some commands are available only when specific input sources are active.  
Source function  
Command  
Parameters  
Description  
SRC  
?
Queries the current active input source: 0=no active  
source,1=VGA-in, 3=composite video, 4=S-video, 8=DVI.  
RSRC  
1, 3, 4, 8, ?  
Attempts to use the specified source as the active input  
source, or queries the last source requested: 1=VGA-in,  
3=composite video, 4=S-video, 8=DVI.  
NXT  
None  
Switches to the next input source.  
AUTO  
0, 1, ?  
Sets or queries automatic searching inputs for signal: 0=no  
searching, 1=searching.  
Video functions  
Command  
Parameters  
Description  
CSPC  
PMOD  
VSHF  
HSHF  
0 to 2, ?  
Sets or queries the active color space: 0=RGB, 1=YPbPr,  
2=YCbCr.  
0,1,5,?  
Sets or queries the picture mode: 0=graphics, 1=video,  
5=custom.  
value, +, –, ?  
value, +, –, ?  
Sets or queries the vertical shift of the projected image:  
usable range is determined by the active input source.  
Sets or queries the horizontal shift of the projected image:  
usable range is determined by the active input source.  
WHIT  
BRT  
0 to 10, +, –, ?  
0 to 100, +, –, ?  
Sets or queries the white intensity.  
Sets or queries the brightness.  
CON  
SAT  
0 to 100, +, –-, ? Sets or queries the contrast.  
0 to 100, +, –, ? Sets or queries the color saturation.  
50 Installing Permanently  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Video functions (continued)  
Command  
TNT  
Parameters  
Description  
–45 to 45, +, –, ? Sets or queries the tint.  
RADJ  
–50 to 50, +, –, ? Sets or queries the amount of red.  
–50 to 50, +, –, ? Sets or queries the amount of green.  
–50 to 50, +, –, ? Sets or queries the amount of blue.  
GADJ  
BADJ  
CTMP  
0 to 2, ?  
Sets or queries the color temperature: 0=warm, 1=neutral,  
2=cool.  
SHRP  
PENH  
KEYV  
0 to 12, +, –, ?  
0 to 6, +, –, ?  
Sets or queries the sharpness.  
Sets or queries the picture enhancement setting.  
–50 to 50, +, –, ? Sets or queries the vertical keystone: 0=no keystone  
adjustment, 1 to 50=shrinks the top of the display,  
–1 to -50=shrinks the bottom of the display.  
ASPT  
SYNC  
FREQ  
TRK  
0, 1, 4, ?  
None  
Sets or queries the aspect ratio: 0=1-to-1, 1=Best Fit,  
4=Reduced.  
Automatically resynchronizes the projector to the active  
computer input source.  
–50 to 50, +, –, ? Sets or queries the projector’s timing relative to the active  
computer input source.  
value, +, –, ?  
value, +, –, ?  
Sets or queries the synchronization of the projector to the  
active computer input source.  
VPOS  
Sets or queries the vertical positioning of the projected  
image: usable range is the maximum and minimum allowed  
by the active computer input source.  
HPOS  
value, +, –, ?  
Sets or queries the horizontal positioning of the projected  
image: usable range is the maximum and minimum allowed  
by the active computer input source.  
HIDE  
WIDE  
KEYR  
0, 1, ?  
0, 1, ?  
None  
Sets or queries picture blanking: 0=not hidden, 1=hidden.  
Sets or queries wide screen mode: 0=normal, 1=wide.  
Resets keystone to zero.  
Connecting to a room controller 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio functions  
Command  
Parameters  
Description  
MUTE  
VOL  
0, 1, ?  
Sets or queries audio muting: 0=not muted, 1=muted.  
0 to 31, +, –, ? Sets or queries audio volume: 0=off, 31=maximum.  
INTSP  
0, 1, ?  
Sets or queries usage of the internal speaker (certain models  
only): 0=disabled, 1=enabled.  
Setup functions  
Command  
Parameters  
Description  
LANG  
0 to 10, ?  
Sets or queries the language used by the projector:  
0=English, 1=French, 2=Italian, 3=German, 4=Portuguese,  
5=Spanish, 6=Traditional Chinese, 7=Simplified Chinese,  
8=Korean, 9=Japanese, 10=Czech.  
LSAV  
LHRS  
THRS  
POS  
0, 1, ?  
Sets or queries low-power operating mode: 0=normal  
power, 1=low power.  
?
Queries the time (in tenths of hours) that the lamp has been  
in use.  
?
Queries the total time (in tenths of hours) that the projector  
has been in use.  
0 to 3, ?  
Sets or queries the projector’s position: 0=front table,  
1=front ceiling, 2=rear table, 3=rear ceiling.  
TMO  
5 to 120, ?  
0, 3 to 6, ?  
Sets or queries the menu timeout setting (seconds)  
PTMO  
Sets or queries the power timeout: 0=never, 3=15 min,  
4=30 min, 5=60 min, 6=120 min.  
EDGE  
VERS  
0, 1, ?  
?
Sets or queries the cleaning of noise from edges of image:  
0=no cleaning, 1=cleaning.  
Queries the projector model number and firmware version.  
The notification takes this form:  
*VERS=”proj_model:proj_fw”  
52 Installing Permanently  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup functions (continued)  
Command  
Parameters  
Description  
FWVERS  
?
Queries the projector firmware model number and firmware  
version. Similar to VERS, but used to verify that a firmware  
update image is appropriate for the projector. The  
notification takes this form:  
*VERS="proj_model:M.mmm"  
IPADDR  
SNET  
Hex IP address, ?  
Used by network module to tell projector the IP address to  
display in the help menu.  
Hex subnet mask, ? Used by network module to tell projector the subnet mask to  
display in the help menu.  
MAC  
Hex MAC address, ? Used by network module to tell projector the MAC address  
to display in the help menu.  
SNUM  
RSET  
?
Queries the projector's serial number.  
Restores all settings to defaults.  
None  
Power and status functions  
Command  
Parameters  
Description  
SHDN  
None  
Puts the projector into cool-down state, and later into standby  
state. The projector sends a notification when it enters cool-  
down state (STAT=3), and another when it enters standby state  
(STAT=0). This keyword requires the projector to be in its on  
state (STAT=1).  
Do not send any requests other than STAT in the time between  
the cool-down and standby state notifications. Otherwise,  
unexpected results can occur.  
W or WAKE  
None  
Puts the projector into warm-up state, and later into on state.  
The projector sends a notification when it enters warm-up state  
(STAT=2), and another when it enters the on state (STAT=1).  
This keyword requires the projector to be in standby state  
(STAT=0).  
Do not send any requests other than STAT in the time between  
the warm-up and on state notifications. Otherwise, unexpected  
results can occur.  
Connecting to a room controller 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Power and status functions (continued)  
Command  
Parameters  
Description  
STAT  
?
Queries the projector's current state: 0=standby state (off),  
1=on, 2=warm-up state, 3=cool-down state.  
ALERT  
Not a request  
Notifies when a system alert condition occurs: 0=lamp life  
warning, 1=lamp life reached, 2=lamp faulty, 3=lamp  
problem, 4=internal temperature too high, 5=fan problem,  
6=ambient temperature too high, 7=color wheel problem,  
8=lamp cover open, 9=ballast faulty.  
ALERT is sent only by the projector, and cannot be used in  
requests.  
Simulated key presses  
Command  
BACK  
ENTER  
LEFT  
Parameters  
Description  
None  
None  
None  
None  
None  
None  
Simulates pressing the Exit Arrow key on keypad  
Simulates pressing the ENTER key on keypad  
Simulates pressing the Left Arrow key on keypad  
Simulates pressing the Right Arrow key on keypad  
Simulates pressing the Up Arrow key on keypad  
Simulates pressing the Down Arrow key on keypad  
RIGHT  
UP  
DOWN  
54 Installing Permanently  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6 Fixing Problems  
Troubleshooting suggestions  
If you have a problem with your projector, check the following statement that most closely  
matches the nature of the problem, then look in that section of this chapter:  
• “Warning light problems” on page 55  
• “Start-up problems” on page 56  
• “Picture problems” on page 56  
• “Sound problems” on page 59  
• “Interruption problems” on page 59  
• “Remote control problems” on page 60  
TIP: If these suggestions do not solve your problem, go to http://www.hp.com/support for  
additional information. To contact HP, refer to the support guide included with the projector.  
Warning light problems  
If both red warning lights are blinking:  
• Allow the projector to cool down after it turns off. If this condition occurs after you  
restart the projector, an internal component has failed. Contact HP for assistance.  
If the red temperature light is on:  
• Allow the projector to cool down after it turns off. Be sure that nothing is near or  
blocking the vents on the projector, and that the vents are free of lint and other objects.  
Remove any sources of excess heat in the room. Observe temperature and altitude limits  
(see “Specifications” on page 61). If the warning light turns on or blinks after you  
restart the projector, contact HP for assistance.  
If the red temperature light is blinking:  
• Contact HP for assistance.  
Troubleshooting suggestions 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
If the red lamp light is on:  
• Install a new lamp. If the lamp light is on after you install a new lamp module, remove  
and reinstall the lamp module. If a new lamp does not fix the problem, contact HP for  
assistance.  
If the red lamp light is blinking:  
• Contact HP for assistance.  
If the red lamp light is flickering quickly:  
• Check that the cover over the lamp at the side of the projector is correctly installed and  
fully attached. Check the tab at the top of the cover and latch at the bottom.  
Start-up problems  
If no lights or sounds turn on:  
• Be sure that the power cable is securely connected to the projector and the other end is  
plugged into an outlet with power.  
• Be sure the disconnect switch is turned on.  
• Press the power button again.  
• Unplug the power cord for 15 seconds, then plug it in and press the power button  
again.  
Picture problems  
If a “scanning” or “waiting” message is displayed on a blank screen:  
• Press the source button on the projector or remote control one or more times until the  
correct source name is selected.  
• Be sure the external source is turned on and connected.  
• For a computer connection, ensure your notebook computer’s external video port is  
turned on. Refer to the computer manual. On some notebooks, for example, press the  
FN+F4 or FN+F5 function keys to turn on the external video port.  
If the wrong input source is displayed:  
• Press the source button on the projector or the remote control one or more times to select  
another active input source.  
56 Fixing Problems  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
If the image is out of focus:  
• Be sure the lens cover is open.  
• While displaying the on-screen menu, adjust the focus ring. (The image size should not  
change; if it does, you are adjusting the zoom, not the focus.)  
• Ensure the projection screen is 1.2 to 10 m (4 to 33 ft) from the projector.  
• Check the projection lens to see if it needs cleaning.  
• For a computer connection, set the display resolution as the computer to the same  
resolution as the projector, 800 × 600 or 1024 × 768 (see “Specifications” on  
page 61). If the computer has multiple monitors, adjust the resolution of the monitor  
assigned to the projector.  
• For a computer connected to the S-video port, the picture cannot be as high resolution  
as what you see on the computer display.  
If an upside-down or reversed image is displayed:  
• The projector has been set to the wrong position setting. Press enter, go to Setup >  
Projector position, and select the correct setting.  
If the image is too small or too large:  
• Adjust the zoom ring on top of the projector.  
• Move the projector closer to or farther from the screen.  
• On the projector or remote control, press the picture mode  
button one or more times  
to see if one of the picture modes makes the image the correct size.  
• Press enter, go to Picture > Customize picture mode > Aspect ratio. Try the different  
settings.  
• If the source device sends wide-screen output, press enter, go to Source, and try setting  
Widescreen input to On. Otherwise, set it to Off.  
If the image has slanted sides:  
• As much as possible, reposition the projector so that it is centered on the screen and  
below the bottom or above the top of the screen.  
• On the projector, press enter, go to Setup > Keystone, and adjust until the sides are  
vertical.  
Troubleshooting suggestions 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If the image is stretched:  
• On the projector or remote control, press the picture mode  
button one or more times  
to see if one of the picture modes makes the image the correct size.  
• Press enter, go to Picture > Customize picture mode > Aspect ratio. Try the different  
settings.  
• If the source device sends wide-screen output, press enter, go to Source, and try setting  
Widescreen input to On. Otherwise, set it to Off.  
If the projected colors seem slightly wrong:  
• See “Adjusting the picture for best color” on page 32.  
• Press enter, go to Help > Diagnostics, and run the color test.  
If the projected colors seem completely wrong:  
• Be sure the pins on the cable connectors are not bent or broken.  
• Press enter, go to Help > Diagnostics, and run the color test.  
• Press enter, go to Picture > Color settings > Reset color settings, and press enter.  
• Press enter, go to Setup > Advanced settings > Reset all settings, and press enter.  
If the picture is not clear (ghost images, smearing, poor quality):  
• Be sure the video cable you are using is coaxial cable rated at 75 ohms. Any other  
cable or impedance rating can reduce picture quality.  
• The video cable connecting the video source to the projector probably must be higher  
quality. See “Choosing cables” on page 44.  
If several picture settings seem completely wrong and you cannot fix them:  
• Press enter, go to Picture > Color settings > Reset color settings, and press enter.  
• Press enter, go to Setup > Advanced settings > Reset all settings, and press enter.  
If a scrolling or cut-off image is displayed for a computer connection:  
• Press the auto sync button on the projector or remote control.  
• Turn everything off. Then power on the projector first and power on the notebook or  
desktop computer second.  
• If the previous steps do not correct the display image, adjust the resolution of the  
notebook or desktop computer to the same resolution as the projector, 800 × 600 or  
1024 × 768 (see “Specifications” on page 61). If the computer has multiple monitors,  
adjust the resolution of the monitor assigned to the projector.  
58 Fixing Problems  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
If the image is flickering or unstable for a computer connection:  
• Press the auto sync button on the projector or remote control.  
• Press enter, go to Picture > VGA settings, and adjust Frequency or Tracking.  
If the image disappears from the computer screen:  
• For a notebook computer, you might be able to turn on both the external VGA port and  
the built-in screen. Refer to the computer manual.  
• Connect a monitor to the VGA-out port.  
If text or lines from a computer display seem rough or uneven:  
• Check the focus adjustment.  
• Press enter, go to Setup > Reset keystone, and press enter.  
Sound problems  
If no sound is coming out of the projector:  
• Be sure you have an audio cable securely connected between the projector and the  
source device.  
• Press enter, go to Setup, and check that Mute is set to Not muted and Volume is correct.  
• Press enter, go to Help > Diagnostics, and run the sound test.  
• Be sure that the mute and volume settings are correct on the source device, such as a  
VCR, camcorder, or computer.  
Interruption problems  
If the projector stops responding to all controls:  
• If possible, turn off the projector, then unplug the power cord and wait at least  
15 seconds before reconnecting power.  
If the lamp shuts off during a show:  
• A minor power surge might cause the lamp to shut off. This is normal. Wait a few  
minutes, then power on the projector.  
• If a red warning light is on or blinking, see “Warning light problems” on page 55.  
If the lamp burns out or makes a popping sound:  
• If the lamp burns out and makes a popping sound, the projector will not turn back on  
until the lamp module has been replaced.  
• If the lamp breaks, contact HP about repairs that might be required due to glass  
fragments.  
Troubleshooting suggestions 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Remote control problems  
If the remote control does not operate:  
• Be sure nothing is blocking the remote control receiver on the front or back of the  
projector. Move to within 8 m (26 ft) of the projector.  
• Aim the remote control at the screen or at the front or back of the projector.  
• Move the remote control so it is more directly in front of or behind the projector and not  
as far to the side.  
• Press enter, go to Help > Diagnostics, and run the remote control test.  
• Replace the battery in the remote control.  
Testing the projector  
Running the projector diagnostics  
The on-screen menu contains diagnostic tests you can use to verify the proper operation of the  
projector and the remote control.  
1. Press enter and go to Help > Diagnostics.  
2. Select a test and press enter.  
3. Follow the displayed instructions.  
60 Fixing Problems  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
7 Reference  
This chapter lists the specifications, safety information, and regulatory information for the  
projector.  
Specifications  
Because HP continually improves its products, the following specifications are subject to  
change. For the latest specifications, visit the HP website at http://www.hp.com.  
Projector specifications  
Size  
309 × 229 × 102 mm (12.2 × 9.0 × 4.0 in.)  
Weight  
3.3 kg (7.3 lb)  
XGA (1024 × 768)  
DLP  
Resolution  
Technology  
Video connectors  
VGA-in (D-sub) with optional cable for component-video input  
VGA-out (D-sub)  
S-video (mini-DIN)  
Composite video (RCA)  
DVI-D (available only on certain models)  
RCA component video (available only on certain models)  
Audio connectors  
Other connectors  
Stereo-in and out (2 mini-phone, available only on certain models)  
USB 1.1 type B  
RS-232 control  
12-Vdc trigger output (available only on certain models)  
Specifications 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Projector specifications (continued)  
Video compatibility  
NTSC-M  
NTSC 4.43 MHz  
PAL-60  
PAL B, D, G, H, I, M, N  
SECAM: B, D, G, K, K1, L  
HDTV (480i/p, 576i/p, 720p, 1080i)  
DVI with HDCP (available only on certain models)  
IR receivers  
Lamp  
Front and back of projector  
300-watt lamp  
2000-hour average lamp life (to half of original brightness)  
Lamp saver mode reduces lamp power to 250 watts, extends life to  
3000 hours  
Replacement lamp: L2139A  
Optics  
1.2 to 10 m (4 to 33 ft) focus range  
7.2 to 8.6 m (23.6 to 28.3 ft) focal length  
1.2:1 optical zoom  
Throw ratio (distance/width)  
Wide: 1.641  
Tele: 1.969  
115% ±5% offset (relative to half-height)  
Light engine  
Audio  
0.7-in. 12° DDR DMD  
Monaural speaker, 2-watt peak output (certain models only)  
Noise level  
Vertical tilt  
Less than 35 dBA in Normal mode, or 32 dBA in lamp saver mode  
0° to 8°  
±15%  
Vertical keystone  
correction  
Remote control  
Mounting options  
Lens cap  
USB mouse  
Ceiling and tabletop, front and rear projection  
Detachable with connecting leash  
Security  
Kensington lock compatible  
Unlock sequence protects against unauthorized use  
62 Reference  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projector specifications (continued)  
Power  
100 to 240 V at 50 to 60 Hz  
Environment  
Operating:  
Temperature: 10 to 35 °C (50 to 95 °F)  
Humidity: 80% RH max, non-condensing  
Altitude: up to 3,000 m (10,000 ft), up to 25 °C (77 °F)  
Storage:  
Temperature: –20 to 55 °C (–4 to 131 °F)  
Humidity: 80% RH max, non-condensing  
Altitude: up to 12,000 m (40,000 ft)  
Video mode compatibility  
Compatibility  
Analog  
Resolution  
Refresh rates (Hz)  
VGA  
640 × 350  
70, 85  
640 × 400  
640 × 480  
720 × 400  
800 × 600  
1024 × 768  
1280 × 1024  
1400 × 1050  
85  
60, 72, 75, 85  
70, 85  
SVGA  
XGA  
56, 60, 72, 75, 85  
60, 70, 75, 85  
60, 75  
SXGA  
SXGA+  
60  
Specifications 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Safety information  
Mercury safety  
WARNING! The lamp in this digital projector contains mercury. If the lamp breaks,  
adequately ventilate the immediate area, discard any nearby food and drink, and thoroughly  
clean the table surface around the projector. Wash your hands after cleaning the area or  
handling a broken lamp. Note that disposal of this lamp may be regulated under applicable  
environmental laws due to presence of mercury. For disposal or recycling information, please  
contact your local authorities or the Electronic Industries Alliance (www.eiae.org). For  
additional safety information about the lamp in this digital projector, please see:  
www.hp.com/hpinfo/globalcitizenship/environment/productdata  
Regulatory information  
This section presents information that shows how your digital projector complies with  
regulations in certain regions. Any modifications to your digital projector not expressly  
approved by HP could void the authority to operate the digital projector in these regions.  
U.S.A.  
This digital projector has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation.  
This digital projector generates, uses, and can radiate radio frequency energy. If not installed  
and used in accordance with the instructions, it can cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this digital projector does cause harmful interference to radio or television  
reception (which can be determined by unplugging the unit), try the following:  
• Reorienting or relocating the receiving antenna.  
• Relocating the digital projector with respect to the receiver.  
• Connecting the digital projector’s power cord to another power outlet.  
64 Reference  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Connections to peripheral devices  
To maintain compliance with FCC Rules and Regulations, use properly shielded cables with  
this device.  
For more information, consult your dealer, an experienced radio/television technician, or,  
prepared by the Federal Communications Commission, How to Identify and Resolve Radio-TV  
Interference Problems. This booklet is available from the U.S. Government Printing Office,  
Washington, DC 20402, Stock Number 004-000-00345-4. At the first printing of this manual,  
the telephone number was 202-512-1800.  
Canada  
This Class B digital apparatus complies with Canadian ICES-003.  
Japan  
Korea  
International  
For regulatory identification purposes, your product is assigned a regulatory model number.  
The regulatory model number for your product is listed in the declaration of conformity. This  
regulatory number is different from the marketing name and product number.  
Regulatory model number: CRVSB-05LE  
Regulatory information 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Declaration of conformity  
According to ISO/IEC Guide 22 and EN 45014  
Hewlett Packard Company  
Manufacturer's name:  
Manufacturer's address:  
Hewlett Packard Company  
Display Technologies and Products  
1000 NE Circle Blvd.  
Corvallis, OR 97330-4239  
Declares, that the product(s):  
Product name:  
Model numbers:  
Regulatory model:  
Digital Projector  
xp7010, xp7030 series  
CRVSB-05LE  
Conforms to the following Product Specifications:  
Safety:  
IEC 60950-1: 2001 / EN 60950-1: 2001  
GB4943-1995  
EMC:  
EN 55022 +A1:2000 +A2:2003 [1]  
CISPR 24:1997 / EN 55024:1998 + A1:2001 +A2:2003  
IEC 61000-3-2:1995 / EN 61000-3-2:2000  
IEC 61000-3-3:1994 / EN 61000-3-3:1995+A1:2001  
GB9254-1998  
FCC Title 47 CFR, Part 15 Class B/ANSI C63.4: 2003  
AS/NZS 3548: 1995 Rules and Regulations of Class B  
VCCI  
Supplementary information:  
The product herewith complies with the requirements of following Directives and carries the CE marking accordingly:  
– Low Voltage Directive: 73/23/EEC  
– EMC Directive: 89/336/EEC  
[1] The product was tested in a typical configuration with Hewlett Packard Personal Computer peripherals.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This  
device may not cause harmful interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation.  
Corvallis, Oregon, October 5, 2005  
Steve Brown, General Manager  
European Contact for regulatory topics only: Hewlett Packard GmbH, HQ-TRE, Herrenberger StraBe 140,  
71034 Boeblingen, Germany. (FAX:+49-7031-143143).  
USA Contact: Hewlett Packard Co., Corporate Product Regulations Manager, 3000 Hanover Street, Palo Alto, CA 94304.  
Phone: (650) 857-1501.  
66 Reference  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recycling information  
Disposal of Waste Equipment by Users in Private Households in the European Union  
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other  
household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated  
collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your  
waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner  
that protects human health and the environment. For more information about where you can drop off your waste equipment  
for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased  
the product.  
Evacuation des équipements usagés par les utilisateurs dans les foyers privés au sein de l'Union européenne  
La présence de ce symbole sur le produit ou sur son emballage indique que vous ne pouvez pas vous débarasser de ce  
produit de la même façon que vos déchets courants. Au contraire, vous êtes responsable de l'évacuation de vos  
équipements usagés et à cet effet, vous êtes tenu de les remettre à un point de collecte agréé pour le recyclage des  
équipements électriques et électroniques usagés. Le tri, l'évacuation et le recyclage séparés de vos équipements usagés  
permettent de préserver les ressources naturelles et de s'assurer que ces équipements sont recyclés dans le respect de la  
santé humaine et de l'environnement. Pour plus d'informations sur les lieux de collecte des équipements usagés, veuillez  
contacter votre mairie, votre service de traitement des déchets ménagers ou le magasin où vous avez acheté le produit.  
Entsorgung von Elektrogeräten durch Benutzer in privaten Haushalten in der EU  
Dieses Symbol auf dem Produkt oder dessen Verpackung gibt an, dass das Produkt nicht zusammen mit dem Restmüll  
entsorgt werden darf. Es obliegt daher Ihrer Verantwortung, das Gerät an einer entsprechenden Stelle für die Entsorgung  
oder Wiederverwertung von Elektrogeräten aller Art abzugeben (z.B. ein Wertstoffhof). Die separate Sammlung und das  
Recyceln Ihrer alten Elektrogeräte zum Zeitpunkt ihrer Entsorgung trägt zum Schutz der Umwelt bei und gewährleistet, dass  
sie auf eine Art und Weise recycelt werden, die keine Gefährdung für die Gesundheit des Menschen und der Umwelt  
darstellt. Weitere Informationen darüber, wo Sie alte Elektrogeräte zum Recyceln abgeben können, erhalten Sie bei den  
örtlichen Behörden, Wertstoffhöfen oder dort, wo Sie das Gerät erworben haben.  
Smaltimento di apparecchiature da rottamare da parte di privati nell'Unione Europea  
Questo simbolo che appare sul prodotto o sulla confezione indica che il prodotto non deve essere smaltito assieme agli  
altri rifiuti domestici. Gli utenti devono provvedere allo smaltimento delle apparecchiature da rottamare portandole al  
luogo di raccolta indicato per il riciclaggio delle apparecchiature elettriche ed elettroniche. La raccolta e il riciclaggio  
separati delle apparecchiature da rottamare in fase di smaltimento favoriscono la conservazione delle risorse naturali e  
garantiscono che tali apparecchiature vengano rottamate nel rispetto dell'ambiente e della tutela della salute. Per ulteriori  
informazioni sui punti di raccolta delle apparecchiature da rottamare, contattare il proprio comune di residenza, il servizio  
di smaltimento dei rifiuti locale o il negozio presso il quale è stato acquistato il prodotto.  
Recycling information 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Eliminación de residuos de aparatos eléctricos y electrónicos por parte de usuarios domésticos en la Unión Europea  
Este símbolo en el producto o en el embalaje indica que no se puede desechar el producto junto con los residuos  
domésticos. Por el contrario, si debe eliminar este tipo de residuo, es responsabilidad del usuario entregarlo en un punto  
de recolección designado de reciclado de aparatos electrónicos y eléctricos. El reciclaje y la recolección por separado de  
estos residuos en el momento de la eliminación ayudará a preservar recursos naturales y a garantizar que el reciclaje  
proteja la salud y el medio ambiente. Si desea información adicional sobre los lugares donde puede dejar estos residuos  
para su reciclado, póngase en contacto con las autoridades locales de su ciudad, con el servicio de gestión de residuos  
domésticos o con la tienda donde adquirió el producto.  
Likvidace vysloužilého zarízení uživateli v domácnosti v zemích EU  
Tato znacka na produktu nebo na jeho obalu oznacuje, že tento produkt nesmí být likvidován prostým vyhozením do  
bežného domovního odpadu. Odpovídáte za to, že vysloužilé zarízení bude predáno k likvidaci do stanovených sberných  
míst urcených k recyklaci vysloužilých elektrických a elektronických zarízení. Likvidace vysloužilého zarízení samostatným  
sberem a recyklací napomáhá zachování prírodních zdroju a zajištuje, že recyklace probehne zpusobem chránícím lidské  
zdraví a životní prostredí. Další informace o tom, kam mužete vysloužilé zarízení predat k recyklaci, mužete získat od  
úradu místní samosprávy, od spolecnosti provádející svoz a likvidaci domovního odpadu nebo v obchode, kde jste  
produkt zakoupili.  
Bortskaffelse af affaldsudstyr for brugere i private husholdninger i EU  
Dette symbol på produktet eller på dets emballage indikerer, at produktet ikke må bortskaffes sammen med andet  
husholdningsaffald. I stedet er det dit ansvar at bortskaffe affaldsudstyr ved at aflevere det på dertil beregnede  
indsamlingssteder med henblik på genbrug af elektrisk og elektronisk affaldsudstyr. Den separate indsamling og genbrug  
af dit affaldsudstyr på tidspunktet for bortskaffelse er med til at bevare naturlige ressourcer og sikre, at genbrug finder sted  
på en måde, der beskytter menneskers helbred samt miljøet. Hvis du vil vide mere om, hvor du kan aflevere dit  
affaldsudstyr til genbrug, kan du kontakte kommunen, det lokale renovationsvæsen eller den forretning, hvor du købte  
produktet.  
Afvoer van afgedankte apparatuur door gebruikers in particuliere huishoudens in de Europese Unie  
Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden afgevoerd met het huishoudelijk  
afval. Het is uw verantwoordelijkheid uw afgedankte apparatuur af te leveren op een aangewezen inzamelpunt voor de  
verwerking van afgedankte elektrische en elektronische apparatuur. De gescheiden inzameling en verwerking van uw  
afgedankte apparatuur draagt bij tot het sparen van natuurlijke bronnen en tot het hergebruik van materiaal op een wijze  
die de volksgezondheid en het milieu beschermt. Voor meer informatie over waar u uw afgedankte apparatuur kunt  
inleveren voor recycling kunt u contact opnemen met het gemeentehuis in uw woonplaats, de reinigingsdienst of de winkel  
waar u het product hebt aangeschaft.  
Eramajapidamistes kasutuselt kõrvaldatavate seadmete käitlemine Euroopa Liidus  
Kui tootel või toote pakendil on see sümbol, ei tohi seda toodet visata olmejäätmete hulka. Teie kohus on viia tarbetuks  
muutunud seade selleks ettenähtud elektri- ja elektroonikaseadmete utiliseerimiskohta. Utiliseeritavate seadmete eraldi  
kogumine ja käitlemine aitab säästa loodusvarasid ning tagada, et käitlemine toimub inimeste tervisele ja keskkonnale  
ohutult. Lisateavet selle kohta, kuhu saate utiliseeritava seadme käitlemiseks viia, saate küsida kohalikust omavalitsusest,  
olmejäätmete utiliseerimispunktist või kauplusest, kust te seadme ostsite.  
Hävitettävien laitteiden käsittely kotitalouksissa Euroopan unionin alueella  
Tämä tuotteessa tai sen pakkauksessa oleva merkintä osoittaa, että tuotetta ei saa hävittää talousjätteiden mukana.  
Käyttäjän velvollisuus on huolehtia siitä, että hävitettävä laite toimitetaan sähkö- ja elektroniikkalaiteromun  
keräyspisteeseen. Hävitettävien laitteiden erillinen keräys ja kierrätys säästää luonnonvaroja. Näin toimimalla varmistetaan  
myös, että kierrätys tapahtuu tavalla, joka suojelee ihmisten terveyttä ja ympäristöä. Saat tarvittaessa lisätietoja jätteiden  
kierrätyspaikoista paikallisilta viranomaisilta, jäteyhtiöiltä tai tuotteen jälleenmyyjältä.  
᜸ᡝ♙ᡞᡞᡖꢀꢁ ♒ᡣᡞꢁꢂꢃꢄꢅ ꢂᡡꢂᡗᡒᡡꢆꢅ ꢂꢃꢁꢅ ᜼ᡡᡞꢄᡝᡎꢇᡗꢈ ꢉꢅꢄꢂꢁ  
ᡇᡜ ꢀꢁꢂꢃꢄ ꢅꢆµꢇᡜꢈᡜ ꢅꢉᡜꢄ ꢊꢋᡜꢀꢈꢌꢅµꢃ ꢍ ꢅꢉꢎ ꢅꢏꢅᡗꢊꢏꢁꢅꢐꢁ ꢉᡜꢏ ꢏꢀᡜᡑꢊꢌᡗꢄꢆꢊꢌ ꢃꢉꢌ ꢉᡜ ꢀꢂᡜꢑꢃꢄ ꢁꢏꢉꢃ ᡑꢊꢄ ꢀꢂꢒꢀꢊꢌ ꢄꢁ ꢀꢊꢉꢁꢓꢉꢊꢐ µꢁꢔꢐ µꢊ  
ꢕꢈꢈꢁ ᡜꢌᡗꢌꢁᡗꢕ ꢁꢀᡜꢂꢂꢐµµꢁꢉꢁ. ꢖꢄꢉꢐꢗꢊꢉꢁ, ꢊꢏꢗꢆꢄꢎ ꢅꢁꢘ ꢊꢐꢄꢁꢌ ꢄꢁ ꢁꢀᡜꢂꢂꢐᡤꢊꢉꢊ ꢉꢌꢘ ꢕꢓꢂꢎꢅꢉꢊꢘ ꢅꢏꢅᡗꢊꢏꢒꢘ ꢅꢊ µꢌꢁ ᡗꢁꢗᡜꢂꢌꢅµꢒꢄꢎ µᡜꢄꢕᡑꢁ  
ꢅꢏꢈꢈᡜꢙꢍꢘ ꢁꢀᡜꢂꢂꢌµµꢕꢉᡥꢄ ꢙꢌꢁ ꢉꢎꢄ ꢁꢄꢁᡗꢆᡗꢈᡥꢅꢎ ꢕꢓꢂꢎꢅꢉᡜꢏ ꢎꢈꢊᡗꢉꢂꢌᡗᡜꢆ ᡗꢁꢌ ꢎꢈꢊᡗꢉꢂᡜꢄꢌᡗᡜꢆ ꢊꢋᡜꢀꢈꢌꢅµᡜꢆ. ᜾ ꢓᡥꢂꢌꢅꢉꢍ ꢅꢏꢈꢈᡜꢙꢍ ᡗꢁꢌ  
ꢁꢄꢁᡗꢆᡗꢈᡥꢅꢎ ꢉᡥꢄ ꢕꢓꢂꢎꢅꢉᡥꢄ ꢅꢏꢅᡗꢊꢏ♝ꢄ ꢗꢁ ꢅꢏµꢇꢕꢈꢈꢊꢌ ꢅꢉꢎ ᡑꢌꢁꢉꢍꢂꢎꢅꢎ ꢉᡥꢄ ᡢꢏꢅꢌᡗ♝ꢄ ꢀꢃꢂᡥꢄ ᡗꢁꢌ ꢉꢎ ᡑꢌꢁꢅᡢꢕꢈꢌꢅꢎ ꢃꢉꢌ ꢗꢁ  
ꢁꢄꢁᡗꢏᡗꢈᡥꢗoꢆꢄ µꢊ ꢉꢂꢃꢀᡜ ♝ꢅꢉꢊ ꢄꢁ ꢀꢂᡜꢅꢉꢁꢉꢊꢆꢊꢉꢁꢌ ꢎ ꢏꢙꢊꢐꢁ ꢉᡥꢄ ꢁꢄꢗꢂ♝ꢀᡥꢄ ᡗꢁꢌ ꢉᡜ ꢀꢊꢂꢌꢇꢕꢈꢈᡜꢄ. ᜺ꢌꢁ ꢀꢊꢂꢌꢅꢅꢃꢉꢊꢂꢊꢘ ꢀꢈꢎꢂᡜᡢᡜꢂꢐꢊꢘ  
ꢅꢓꢊꢉꢌᡗꢕ µꢊ ꢉᡜ ꢀᡜꢆ µꢀᡜꢂꢊꢐꢉꢊ ꢄꢁ ꢁꢀᡜꢂꢂꢐᡤꢊꢉꢊ ꢉꢌꢘ ꢕꢓꢂꢎꢅꢉꢊꢘ ꢅꢏꢅᡗꢊꢏꢒꢘ ꢙꢌꢁ ꢁꢄꢁᡗꢆᡗꢈᡥꢅꢎ, ꢊꢀꢌᡗᡜꢌꢄᡥꢄꢍꢅꢉꢊ µꢊ ꢉꢌꢘ ᡗꢁꢉꢕ ꢉꢃꢀᡜꢏꢘ  
ꢁꢂµꢃᡑꢌꢊꢘ ꢁꢂꢓꢒꢘ ꢍ ꢉᡜ ᡗꢁꢉꢕꢅꢉꢎµꢁ ꢁꢀꢃ ꢉᡜ ᡜꢀᡜꢐᡜ ꢁꢙᡜꢂꢕꢅꢁꢉꢊ ꢉᡜ ꢀꢂᡜꢑꢃꢄ.  
68 Reference  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A hulladékanyagok kezelése a magánháztartásokban az Európai Unióban  
Ez a szimbólum, amely a terméken vagy annak csomagolásán van feltüntetve, azt jelzi, hogy a termék nem kezelheto  
együtt az egyéb háztartási hulladékkal. Az Ön feladata, hogy a készülék hulladékanyagait eljuttassa olyan kijelölt  
gyujtohelyre, amely az elektromos hulladékanyagok és az elektronikus berendezések újrahasznosításával foglalkozik. A  
hulladékanyagok elkülönített gyujtése és újrahasznosítása hozzájárul a természeti eroforrások megorzéséhez, egyúttal azt  
is biztosítja, hogy a hulladék újrahasznosítása az egészségre és a környezetre nem ártalmas módon történik. Ha  
tájékoztatást szeretne kapni azokról a helyekrol, ahol leadhatja újrahasznosításra a hulladékanyagokat, forduljon a helyi  
önkormányzathoz, a háztartási hulladék begyujtésével foglalkozó vállalathoz vagy a termék forgalmazójához.  
Lietot੗ju atbrꢀvošan੗s no nederꢀg੗m ierꢀcɶm Eiropas Savienꢀbas priv੗taj੗s m੗jsaimniecꢀb੗s  
Šis simbols uz ierꢀces vai tꢁs iepakojuma norꢁda, ka šo ierꢀci nedrꢀkst izmest kopꢁ ar pꢁrɶjiem mꢁjsaimniecꢀbas atkritumiem.  
Jꢂs esat atbildꢀgs par atbrꢀvošanos no nederꢀgꢁs ierꢀces, to nododot norꢁdꢀtajꢁ savꢁkšanas vietꢁ, lai tiktu veikta nederꢀgꢁ  
elektriskꢁ un elektroniskꢁ aprꢀkojuma otrreizɶjꢁ pꢁrstrꢁde. Speciꢁla nederꢀgꢁs ierꢀces savꢁkšana un otrreizɶjꢁ pꢁrstrꢁde palꢀdz  
taupꢀt dabas resursus un nodrošina tꢁdu otrreizɶjo pꢁrstrꢁdi, kas sargꢁ cilvɶku veselꢀbu un apkꢁrtɶjo vidi. Lai iegꢂtu papildu  
informꢁciju par to, kur otrreizɶjai pꢁrstrꢁdei var nogꢁdꢁt nederꢀgo ierꢀci, lꢂdzu, sazinieties ar vietɶjo pašvaldꢀbu,  
mꢁjsaimniecꢀbas atkritumu savꢁkšanas dienestu vai veikalu, kurꢁ iegꢁdꢁjꢁties šo ierꢀci.  
Europos Séjungos vartotojꢁ ir privačiꢁ namꢁ ʦkiꢁ atliekamos ʂrangos išmetimas  
Šis simbolis ant produkto arba jo pakuotꢃs nurodo, kad produktas negali bꢂti išmestas kartu su kitomis namꢄ ꢂkio atliekomis.  
Jꢂs privalote išmesti savo atliekamꢅ ꢆrangꢅ atiduodami jꢅ ꢆ atliekamos elektronikos ir elektros ꢆrangos perdirbimo punktus. Jei  
atliekama ꢆranga bus atskirai surenkama ir perdirbama, bus išsaugomi natꢂralꢂs ištekliai ir užtikrinama, kad ꢆranga yra  
perdirbta žmogaus sveikatꢅ ir gamtꢅ tausojančiu bꢂdu. Dꢃl informacijos apie tai, kur galite išmesti atliekamꢅ perdirbti skirtꢅ  
ꢆrangꢅ kreipkitꢃs ꢆ atitinkamꢅ vietos tarnybꢅ, namꢄ ꢂkio atliekꢄ išvežimo tarnybꢅ arba ꢆ parduotuvê, kurioje pirkote produktꢅ.  
Utylizacja zuzytego sprzetu przez uzytkowników domowych w Unii Europejskiej  
Symbol ten umieszczony na produkcie lub opakowaniu oznacza, ze tego produktu nie nalezy wyrzucac razem z innymi  
odpadami domowymi. Uzytkownik jest odpowiedzialny za dostarczenie zuzytego sprzetu do wyznaczonego punktu  
gromadzenia zuzytych urzadzen elektrycznych i elektronicznych. Gromadzenie osobno i recykling tego typu odpadów  
przyczynia sie do ochrony zasobów naturalnych i jest bezpieczny dla zdrowia i srodowiska naturalnego. Dalsze  
informacje na temat sposobu utylizacji zuzytych urzadzen mozna uzyskac u odpowiednich wladz lokalnych, w  
przedsiebiorstwie zajmujacym sie usuwaniem odpadów lub w miejscu zakupu produktu.  
Descarte de equipamentos por usuários em residências da União Européia  
Este símbolo no produto ou na embalagem indica que o produto não pode ser descartado junto com o lixo doméstico. No  
entanto, é sua responsabilidade levar os equipamentos a serem descartados a um ponto de coleta designado para a  
reciclagem de equipamentos eletro-eletrônicos. A coleta separada e a reciclagem dos equipamentos no momento do  
descarte ajudam na conservação dos recursos naturais e garantem que os equipamentos serão reciclados de forma a  
proteger a saúde das pessoas e o meio ambiente. Para obter mais informações sobre onde descartar equipamentos para  
reciclagem, entre em contato com o escritório local de sua cidade, o serviço de limpeza pública de seu bairro ou a loja  
em que adquiriu o produto.  
Postup používateꢀov v krajinách Európskej únie pri vyhadzovaní zariadenia v domácom používaní do odpadu  
Tento symbol na produkte alebo na jeho obale znamená, že nesmie by″ vyhodený s iným komunálnym odpadom.  
Namiesto toho máte povinnos″ odovzda″ toto zariadenie na zbernom mieste, kde sa zabezpečuje recyklácia elektrických  
a elektronických zariadení. Separovaný zber a recyklácia zariadenia určeného na odpad pomôže chráni″ prírodné  
zdroje a zabezpečí taký spôsob recyklácie, ktorý bude chráni″ ꢀudské zdravie a životné prostredie. ꢁalšie informácie o  
separovanom zbere a recyklácii získate na miestnom obecnom úrade, vo firme zabezpečujúcej zber vášho komunálneho  
odpadu alebo v predajni, kde ste produkt kúpili.  
Ravnanje z odpadno opremo v gospodinjstvih znotraj Evropske unije  
Ta znak na izdelku ali embalaži izdelka pomeni, da izdelka ne smete odlagati skupaj z drugimi gospodinjskimi odpadki.  
Odpadno opremo ste dolžni oddati na določenem zbirnem mestu za recikliranje odpadne električne in elektronske opreme.  
Z ločenim zbiranjem in recikliranjem odpadne opreme ob odlaganju boste pomagali ohraniti naravne vire in zagotovili, da bo  
odpadna oprema reciklirana tako, da se varuje zdravje ljudi in okolje. Več informacij o mestih, kjer lahko oddate odpadno  
opremo za recikliranje, lahko dobite na občini, v komunalnem podjetju ali trgovini, kjer ste izdelek kupili.  
Recycling information 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Kassering av förbrukningsmaterial, för hem- och privatanvändare i EU  
Produkter eller produktförpackningar med den här symbolen får inte kasseras med vanligt hushållsavfall. I stället har du  
ansvar för att produkten lämnas till en behörig återvinningsstation för hantering av el- och elektronikprodukter. Genom att  
lämna kasserade produkter för återvinning hjälper du till med att bevara våra gemensamma naturresurser. Dessutom  
skyddas både människor och miljön när produkter återvinns på rätt sätt. Kommunala myndigheter, sophanteringsföretag  
eller butiken där varan köptes kan ge mer information om var du lämnar kasserade produkter för återvinning.  
70 Reference  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
composite-video  
connecting source 22  
port 10  
computer screen, showing  
28  
computer, connecting 16  
connecting  
A
H
accessories 12  
handheld organizer,  
connecting 17  
adjusting  
color 32  
hiding picture 28  
picture 29  
I
setup 33  
shape of picture 30  
slanted picture 31  
sound 29  
image. See picture  
component-video source  
19, 20  
composite-video source  
22  
computer 16  
DVI source 18  
external accessory 46  
handheld organizer 17  
power 15  
installing projector 13, 44  
aiming projector 25  
analog video mode  
compatibility 63  
audio  
L
lamp, replacing 40  
lens, cleaning 39  
lights. See lamp; warning  
lights  
adjusting 29  
ports 10  
locking projector 33, 45  
troubleshooting 59  
audio, connecting  
room controller 47  
SCART source 18  
S-video source 21  
controlling external  
accessory 46  
M
menu  
B
language 35  
listing 34  
buttons  
location 9  
opening menu 34  
using 34  
mercury safety 64  
moving projector 24  
D
default settings, changing  
34  
C
cables  
O
diagnostics 60  
DVI video  
choosing 44  
on-screen menu. See menu  
connections 18  
ceiling installation 45  
choosing cables 44  
cleaning 6, 39  
component-video  
connecting RCA source  
20  
connecting source 18  
port 10  
P
PC. See computer  
picture  
E
focus 25  
external accessory 46  
hiding and showing 28  
quality of 13, 18, 58  
troubleshooting 56  
zoom 25  
F
connecting source with  
component-to-VGA  
cable 19  
firmware, updating 43  
focus 25  
picture mode, choosing 29  
port 10  
Index  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
power  
slanted picture, adjusting  
31  
specifications 61  
S-video  
Y
connecting 15  
YPbPr. See component-  
video  
turning off 24  
turning on 23  
presentations, showing 28  
projector, locking 33  
connecting source 21  
port 10  
Z
zoom 25  
Q
T
quality of picture 18, 58  
table installation 13, 44  
triggering external  
accessory 46  
R
troubleshooting  
audio 59  
rear projection installation  
45  
interruptions 59  
picture 56  
remote control 60  
start-up 56  
recycling information 67  
regulatory information 64  
remote control  
buttons 11  
warning lights 55  
turning on and off 23  
installing batteries 42  
opening menu 34  
troubleshooting 60  
using 26  
U
replacing lamp 40  
room controller 47  
room layout 13  
RS-232 47  
unlocking projector 33  
updating firmware 43  
upgrading projector 43  
USB, connecting 16  
using remote control 26  
S
V
VGA  
safety information 6, 64  
SCART 18  
screen  
connecting source 16,  
17  
port 11  
controlling 46  
positioning 14  
security  
video mode compatibility  
63  
video source, selecting 28  
locking cable 45  
security code 33  
selecting video source 28  
serial port 47  
connector 47  
setting up 13  
shape, adjusting 30  
showing picture 28  
showing presentations 28  
W
warning lights  
location 9  
meanings 55  
troubleshooting 55  
72 Index  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Hans Grohe Indoor Furnishings 39116XX1 User Manual
Heat Glo LifeStyle Indoor Fireplace fb grand User Manual
Hotpoint Dishwasher HDA2600K User Manual
Hotpoint Refrigerator FFL49 User Manual
HP Hewlett Packard All in One Printer 3070A User Manual
Humax DVR CX PVR 9200C User Manual
Husqvarna Blower 111750 HCS1372 User Manual
Husqvarna Chainsaw 1153176 26 User Manual
Hyundai IT Computer Monitor U90P User Manual
Ikelite Camera Accessories G11 User Manual