HP Hewlett Packard Personal Computer A7H84UAABA User Manual

QuickSpecs  
Overview  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
1. Power LED/Beep LED  
3. 15” TFT 5-Wire Resistive Touch Screen – standard on all  
models  
2. Multi-Track (3) Magnetic Stripe Reader (MSR) - Available on  
select models  
1. Two 2.5” Storage Drive bays  
5. Advertisement panel (non-electrical)  
2. One USB 2.0 port, one audio line-out and one microphone- 6. Main display hinge, allows for 90-degree pitch adjustment  
in jack  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Standard Features  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
Processors  
Intel® Celeron® 440 (2.0 GHz, 512K L2 Cache, 800 MHz FSB)  
Intel Core™ 2 Duo E7400 (2.8 GHz, 3 MB L2 Cache, 1066 MHz FSB)  
Operating System  
Preinstalled  
Genuine Windows 7 Professional 32-bit*  
Genuine Windows 7 Professional 64-bit*  
FreeDOS  
Windows Embedded POS Ready 2009  
*This system may require upgraded and/or separately purchased hardware and/or a DVD drive to install  
the Windows 7 software and take full advantage of Windows 7 functionality. See  
Factory preinstall not available. Drivers support only.  
Graphics  
Display  
Integrated Intel Graphics Media Accelerator 3000  
15-inch diagonal TFT dual-bulb display, 1024 x 768 resolution, with 5-wire resistive type touchscreen.  
Precalibrated at factory but should be recalibrated after initial software via the calibration wizard. Hard  
or soft stylus input: finger tip, finger nail, or credit card edge to perform touch.  
Touch Technology  
Resolution  
Max Color  
5-wire resistive type  
1024 x 768  
16.7M  
Contrast Ratio  
Brightness  
800:1  
300 cd/m  
2
Pixel Pitch  
0.297mm  
Viewing Angle  
Response rate  
140° horizontally and 140° vertically  
2ms (rise time), 6ms (decay time)  
Default Color Temperature 6488° K  
Anti Glare Harness  
Color Gamut  
Backlight Units  
3H  
61.56%  
2 CCFL  
Memory  
Dual-channel  
DDR2 up to 4 GB capacity, 2 slots, supports 800 MHz; most configurations  
ship with 1 x 2GB or 1 x 1 GB + 1 x 2 GB (3 GB)  
Configurable Model: (Available in AsiaPacific region only)  
1-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (1 x 1 GB)  
2-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (1 x 2 GB)  
2-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (2 x 1 GB)  
3-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (1 x 1 GB, 1 x 2  
GB)  
4-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (2 x 2 GB)  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Standard Features  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
NIC  
Realtek RTL8111C Ethernet Connection, 10/100/1000, with WOL support  
LAN STATUS:  
10MB  
100MB  
1000MB  
Activity is occurring (Left LED ACTIVE  
LED):  
LED ACTIVE  
LED ACTIVE  
Link Status  
(right LED):  
None  
LED On  
LED On  
Keyboard  
Keyboard not included. PS/2 or USB supported.  
NOTE: A keyboard is required to unbundle the software image.  
Pointing Device  
Pointing Device not included. USB supported. Pointing devices include a mouse, trackball, touch pad,  
etc.  
Multi Track (3) Magnetic Integrated MSR available on some select models. Conforms to ANSI/ISO 7810, 7811 1/5, 7812, and  
stripe reader (MSR)  
7813;  
Supports OPOS and JPOS drivers layer; 3 tracks: IATA, ABA, THRIFT; bi-directional swipe, LED indicates  
status of reader.  
NOTE: The MSR is standard on some models and optional on others  
Vacuum Fluorescent  
2 line x20 character display (40 characters total), RS232 interface, DC 5Volts (V) (COM 2 port set to 5V  
Display (VFD) (Customer at HP factory in BIOS setup). Supports complex character set, control commands, user-defined fonts and  
Facing)  
international fonts. Display pitch adjustment 80 degrees (10 degrees to 90 degrees)  
WARNING: VFD must be connected to the COM 1 or COM 2 port (It should not be connected to  
COM3 port because COM 3 does not support DC5V. Connecting the VFD into COM 3 port may  
damage the VFD COM 1 may be used for the VFD but 5V will need to be selected in BIOS Setup for  
COM 1.  
NOTE: The VFD occupies COM 2 port from the HP factory. Although three COM ports are present on  
the HP ap5000, COM 2 port is occupied by the VFD on factory configured models; therefore, only two  
COM ports are available to the end user when the VFD is installed.  
NOTE: The VFD is standard on select models and also available as an optional kit  
Advertisement panel  
This non-electrical panel features a clear cover. It may be removed so that print material/advertisements  
can be displayed. HP provides a template for the advertisement panel.  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Standard Features  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
Storage  
Hard Drive or Solid State (2) 2.5" internal storage bays: 160 GB or 250GB 2.5" Hard Disk Drive  
Drive  
(HDD) (select models), 64 GB or 80GB 2.5" Solid State Drive (SSD) (select  
models)  
NOTE: The ap5000 can be configured with a combination of the 160 GB,  
250 GB HDD or 64 GB, 80 GB SSD; however, if RAID 1 is requested from  
the HP Factory, both storage bays must contain the same size drive.  
External USB only (not included).  
Optical Drive  
VGA  
NOTE: an optical drive is required to restore the software image.  
I/O Panel  
1
Warning: This is a Powered VGA Port. Do not hot plug a monitor into the VGA port. Doing so may  
damage the monitor. Always power down the ap5000 when removing or attaching a monitor to the VGA  
port.  
USB 2.0  
6: 5 (located at bottom of main display behind access panel), 1 left side  
(behind access panel)  
Audio line out  
Microphone in  
Power connector  
RJ-45/Ethernet  
RS232 ports  
1
1
1: DC 19Volts for 130W AC power adapter  
1
3: COM 1 and COM 2 (5 V configurable in BIOS), COM 3 (12V  
configurable in BIOS)  
NOTE: When the HP 2-line VFD is preconfigured by the HP factory,  
COM 2 port is occupied. When the optional 10.4” Customer Facing  
Display is installed, all three COM ports become available.  
USB+power  
1: 24 Volts  
Keyboard (PS/2)  
Parallel port  
1
1
Kensington Lock Hole  
2 (lock kit sold separately)  
Warning: This is a Powered VGA Port. Do not hot plug a monitor into the VGA port. Doing so may  
damage the monitor. Always power down the ap5000 when removing or attaching a monitor to the VGA  
port.  
I/O Panel Layout:  
(screen side)  
NOTE: I/O Panel located at rear, lower side of display under cover; I/O view when facing 15" touch  
screen and bottom flipped up  
Audio/Visual  
Intel integrated high-definition audio with 2-channel Via VT1708S codec  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Standard Features  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
Software  
Preinstalled software  
PDF Complete, HP Client Automation Agent  
McAfee Total Protection (Windows 7 and Windows XP only)  
Power Manager  
Advanced Configuration and Power Management Interface (ACPI) allows the system to wake from a low  
power mode.  
NOTE: Power button is located on I/O panel and concealed under the I/O cover.  
SMBIOS  
Security  
System Management BIOS, previously known as DMI BIOS, for system management information  
Kensington Lock Support, (located in two places: underneath the base and on I/O panel), Power-On  
password protection, Setup password protection, USB port disable.  
Power Supply  
130 W AC power adapter, ENERGY STAR 5.0 qualified, European Union 2005/32/EC (EUP LOT 6,  
EUP LOT 7), input 90 to 260 VAC; Frequency range 47 to 63 Hz  
Service and Support  
Standard 3/3/3 limited warranty: 3 years parts, 3 years labor, 3 years on-site service. OS support for 90  
days; quick restore solution included (requires external optical drive/not included)  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Options  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
Customer Facing Displays HP 2-line x 20 characters, Vacuum Florescent Display (VFD) kit  
HP 10” LCD Customer facing display kit  
BV495AA  
AZ191AA  
Magnetic Stripe Reader  
Hard Drives  
HP ap5000 Magnetic Stripe Reader  
BZ721AA  
HP 160GB 7.2K SATA 3.0-Gb/s 2.5” Hard Disk Drive  
HP 250GB 7.2K SATA 3.0-Gb/s 2.5" Hard Disk Drive  
HP ap5000 64GB SATA 2.5” Solid State Drive  
BS582AA  
BZ724AA  
BT391AA  
HP 80 GB Solid State Drive for HP Business Desktop PCs  
BM848AV**  
NOTE: Drive caddy included with HP ap5000 base system  
*Alternative if BT391AA is not available for 64GB.  
Optical Drives  
External USB CD/DVD R/RW Drive  
FS943AA#ABA  
Input/Output Devices  
HP USB 2-Button Optical Scroll Mouse  
HP USB Washable Keyboard  
DC172AT  
VF097AA  
POS Peripherals  
HP Heavy Duty Cash Drawer  
FK182AA  
BW867AA  
EY022AA  
BW868AA  
FK224AA  
FK184AA  
HP Flip-Top Cash Drawer  
HP Laser Barcode Scanner  
HP Imaging Barcode Scanner  
HP USB Single Station Thermal Receipt Printer  
HP USB Multifunction Thermal Receipt Printer with MICR  
Memory (DIMMs)  
HP 1 GB PC2-6400 (DDR2 800 MHz)  
HP 2 GB PC2-6400 (DDR2 800 MHz)  
BZ722AA*  
BZ723AA**  
* Desktop PC memory AH058AA also compatible  
** Desktop PC memory AH060AA also compatible  
Security  
HP Keyed Cable Lock  
BV411AA  
Accessories  
HP ap5000 Wall Mount kit  
BT390AA  
EM870AA  
DT527A  
HP Quick Release Mechanism Kit (for use with Wall Mount Kit)  
HP PS/2 Standard Keyboard  
HP PS/2 2-Button Optical Scroll Mouse  
HP USB-P/S2 Optical Mouse  
EY703AA  
DC369A  
RH304AA  
HP USB Optical Travel Mouse  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Technical Specifications  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
System Unit  
Dimensions (HxWxD)  
(12.40 x 15.79 x 9.33 in) 31.5 x 40.1 x 23.7 cm  
Bottom footprint:  
(W: 9.84 x D: 9.33 in) W: 25.0 x D: 23.7 cm  
Weight  
24.36 lb (11.05 kg)  
Stand-Alone Power  
Requirements  
Electrical Ratings  
Average Operating Power 47.3W under normal operation  
90 to 264 VAC; 47 to 63 Hz  
Max Operating Power  
Operating  
Non-operating  
Operating  
Operating  
Non-operating  
130 watts  
Temperature  
50° to 104° F (10 to 40° C)  
-20° to 140° F (-30° to 60° C)  
20 to 85%  
0 to 10,000 ft (3,048 m)  
0 to 30,000 ft (9,144 m)  
Relative Humidity  
Altitude  
(unpressurized)  
Industry Standard  
Certifications  
UL, CSA, FCC Compliance, ENERGY STAR®, EPEAT® Silver  
Integrated Graphics  
Media Accelerator 3000  
Graphic Controller  
Bus type  
Integrated GMA 3000  
Integrated  
RAMDAC  
Single 400 MHz integrated  
Memory  
UMA with DVMT 4.0 support for frame buffer sizes 8-256 MB  
Controller clock speed  
Overlay planes  
Maximum Color Depth  
667 MHz  
One 16-bit video overlay plane  
32 bpp  
Maximum vertical refresh 85 Hz  
rate  
Multi-display Support  
Dual independent monitor support through secondary VGA interface.  
Primary display is 15" touch screen. Optional, secondary 10” LCD Customer  
Facing Display may be attached to VGA port in I/O Panel.  
Graphics/Video API  
Support  
DirectX 9.0c, WGF 1.0, DirectX VA 2.0, Shader Model 3.0, OpenGL 1.5  
1
Resolutions Supported  
Resolution  
Maximum Refresh Rate (Hz)  
Analog Monitor Digital Monitor  
85 60  
640 x 480  
800 x 600  
85  
85  
85  
85  
85  
85  
60  
60  
60  
60  
60  
60-R  
60-R  
1024 x 768  
1280 x 1024  
1600 x 1200  
1920 x 1080  
1920 x 1200  
1920 x 1440  
2
2
N/A  
NOTES:  
1
Modes listed are supported with a single active display. The supported mode list for multiple active  
displays is a subset of this list. Not all modes will support video playback and some supported modes  
may use software MC (motion compensation) rather than hardware MC. Not all modes will support 3D  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Technical Specifications  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
acceleration depending on the system configuration (e.g., resolution selected, size of frame buffer,  
number of installed memory modules, etc.).  
2
-R denotes reduced blanking timings (some digital monitors may not support reduced blanking  
timings).  
2.5" 7200 RPM Serial  
ATA Hard Drive  
250-GB  
Capacity  
Height  
Width  
250,059,350,016 bytes  
0.374 in (9.5 mm)  
Media diameter: 2.5 in (63.5 mm)  
Physical size: 2.75 in (70 mm)  
Serial ATA (3.0 Gb/s)  
Interface  
Synchronous Transfer  
Rate (Maximum)  
Up to 3 Gb/s  
Cache  
8 MB  
Seek Time (typical reads, Single Track  
2.0 ms  
12 ms  
22 ms  
includes controller  
overhead, including  
Average  
Full-Stroke  
settling)  
Rotational Speed  
Logical Blocks  
7,200 rpm  
488,397,168  
Operating Temperature 41° to 131°F (5° to 55°C)  
160-GB  
Capacity  
Height  
Width  
160,041,885,696 bytes  
0.374 in (9.5 mm)  
Media diameter: 2.5 in (63.5 mm)  
Physical size: 2.75 in (70 mm)  
Serial ATA (3.0 Gb/s)  
Interface  
Synchronous Transfer  
Rate (Maximum)  
Up to 3 Gb/s  
Cache  
8 MB  
Seek Time (typical reads, Single Track  
2.0 ms  
12 ms  
22 ms  
includes controller  
overhead, including  
Average  
Full-Stroke  
settling)  
Rotational Speed  
Logical Blocks  
7,200 rpm  
312,581,808  
Operating Temperature 41° to 131°F (5° to 55°C)  
2.5" Solid State Drives  
80-GB  
Unformatted Capacity*  
Architecture  
80 GB  
Multi Level Cell (MLC) NAND Flash with wear  
leveling 10 channel controller  
Interface type  
SATA 3Gb/sec  
Dimensions-external  
(W x H x D)  
2.74 x 0.37 x 4 in (6.98 x 0.95 x 10.2 cm)  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Technical Specifications  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
Weight  
0.18 lb (80 g)  
Bandwidth Performance Sustained Sequential  
Read  
Up to 250 MB/s  
Up to 70 MB/s  
Sustained Sequential  
Write  
Random Read (4KB)  
Random Write (4KB)  
up to 35K IOPs  
up to 6.6K IOPs  
65 ms  
Latency  
Read  
Write  
85 ms  
Power  
Total power  
consumption  
0.15 Watt (Active);  
0.075 Watt (Idle)  
Useful drive life  
5 years  
35TB written, up to  
20GB/day for 5 years  
Environmental  
(all conditions, non-  
condensing)  
Temperature  
(operating)  
32° to 158° F (0° to 70°  
C)  
Relative Humidity  
(operating)  
5% to 95%  
Maximum Wet Bulb  
Temperature  
84° F (29° C)  
(operating)  
Shock (operating)  
1,500 G/0.5 msec  
Regulations  
UL, CSA, EN 60950-2000, CISPR Pub 22 Class  
B, CNS 13438, AS/NZS CISPR 22:2002 Class  
B, R1113 and C1172 Class B  
* For solid state disk drives, GB means 1 billion bytes. 80GB is the  
unformatted capacity of this drive before a portion of the drive is reserved for  
flash management features. Actual capacity will vary by content  
64-GB  
Unformatted Capacity  
NAND Flash Memory  
64 GB  
Multi Level Cell (MLC) with wear leveling  
controller  
Interface type  
SATA 3Gb/sec  
Dimensions-external  
(W x H x D)  
2.74 x 0.37 x 4 in (6.98 x 0.95 x 10.2 cm)  
Weight  
0.14 lb (65 g)  
Internal transfer rate  
Write speed  
Up to 220 MB/s  
Up to 120 MB/s  
Up to 150 MB/s  
Read speed  
Host transfer rate  
Ultra DMA mode  
Environmental  
(all conditions, non-  
condensing)  
Temperature  
(operating)  
32° to 158° F (0° to 70°  
C)  
Relative Humidity  
(operating)  
5% to 95%  
Maximum Wet Bulb  
Temperature  
84° F (29° C)  
(operating)  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Technical Specifications  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
Regulations  
UL, CSA, EN 60950-2000, CISPR Pub 22 Class  
B, CNS 13438, AS/NZS CISPR 22:2002 Class  
B, R1113 and C1172 Class B  
ROM BIOS Information  
Key features of the HP BIOS in the ap5000 include:  
Security – Power on password, F-10 Setup password, USB port disable,  
Thermal and power management – The BIOS provides and enables thermal and power management technologies  
Administrator password – Also known as the setup password, this helps prevent unauthorized changes to the system  
configuration. If the administrator password is not known, the BIOS version cannot be changed and changes cannot be made  
to BIOS settings using F10 setup or under the OS.  
Advanced Configuration and Power Interface (ACPI) – Represents a significant innovation in power and configuration  
management, allowing operating systems and applications to manage power based on activity and usage. Provides power  
conservation features under Windows XP.  
Ability to disable the internal speaker  
Other Features  
Description  
ACPI-Ready Hardware  
Advanced Configuration and Power Management Interface (ACPI) allows the system to wake from a low  
power mode.  
SMBIOS Ver. 2.4  
System Management BIOS, previously known as DMI BIOS, for system management information  
Dual-State Power Button Power button acts as both an on/off button and suspend-to-sleep button  
Serviceability Features of System  
Dual Color Power LED on Front of Computer (Indicates Normal Operations and Fault Conditions)  
Diagnostic LED Explanation Table  
Number of repeated red LED blinks:  
2-processor thermal protection activated  
3-processor not installed  
4-power supply failure  
5-memory error  
6-video error  
7-PCA failure (ROM detected failure prior  
to video)  
8-invalid ROM, bootblock recover mode  
Flash Recovery with Video  
Restore CD  
DIMM Connectors for easy Upgrade  
NIC LEDs (integrated)  
Socketed Processor for easy Upgrade  
DIMM Connectors for easy Upgrade  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Technical Specifications  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
Serviceability Features of Chassis  
Dual Color Power LED – To indicate normal operations and fault conditions  
System memory can be upgraded  
Tool-less removal power supply  
Feature  
Description  
ASF 2.0 support (Alert Standard Format)  
Industry-standard specification for network alerting and remote  
control in operating system-absent environments  
SMART Technology  
(Self-Monitoring, Analysis and Reporting Technology)  
Allows hard drives to monitor their own health and to raise flags if  
imminent failures were predicted  
Predicts failures before they occur. Tracks fault prediction  
and failure indication parameters such as re-allocated  
sector count, spin retry count, calibration retry count  
By avoiding actual hard drive failures, SMART hard drives  
act as "insurance" against unplanned user downtime and  
potential data loss from hard drive failure  
Eco-Label Certifications & This product has received or is in the process of being certified to the following approvals and may be  
declarations  
labeled with one or more of these marks:  
US ENERGY STAR®  
IT ECO declaration  
registration status in your country.  
Energy Consumption  
Normal Operation  
115 VAC  
34 W  
230 VAC  
29 W  
100 VAC  
33.5 W  
1 W  
Sleep (Energy Star low  
power mode)  
1 W  
1.1 W  
Off  
0.8 W  
0.9 W  
0.8 W  
Heat Dissipation*  
Normal Operation  
Sleep  
115 VAC  
116 BTU/hr  
3 BTU/hr  
230 VAC  
99 BTU/hr  
4 BTU/hr  
3 BTU/hr  
100 VAC  
115 BTU/hr  
3 BTU/hr  
Off  
3 BTU/hr  
3 BTU/hr  
* Heat dissipation is calculated based on the measured watts, assuming the service level is attained for  
one hour.  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Technical Specifications  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
Declared Noise Emissions  
(in accordance with  
ISO 7779 and ISO 9296)  
System Fan  
Sound Power  
(LWAd, bels)  
Sound Pressure  
(LpAm, decibels)  
Idle (Fan,  
3.6  
26.9  
default speed)  
Fixed Disk  
4.4  
34  
(random writes)  
Batteries  
This battery(s) in this product comply with EU Directive 2006/66/EC  
Batteries used in the product do not contain:  
Mercury greater the 5ppm by weight  
Cadmium greater than 10ppm by weight  
Battery size: CR2032 (coin cell)  
Battery type: Lithium Metal  
RoHS Compliance  
Material Usage  
Hewlett-Packard is committed to compliance with all applicable environmental laws and regulations,  
including the European Union Restriction of Hazardous Substances (RoHS) Directive. HP's goal is to  
exceed compliance obligations by meeting the requirements of the RoHS Directive on a worldwide basis.  
By July 1, 2006, RoHS substances will be virtually eliminated (virtually = to levels below legal limits) for  
all HP electronic products subject to the RoHS Directive, except where it is widely recognized that there is  
no technically feasible alternative (as indicated by an exemption under the EU RoHS Directive).  
This product does not contain any of the following substances in excess of regulatory limits (refer to the  
Asbestos  
Certain Azo Colorants  
Certain Brominated Flame Retardants – may not be used as flame retardants in plastics  
Cadmium  
Chlorinated Hydrocarbons  
Chlorinated Paraffins  
Formaldehyde  
Halogenated Diphenyl Methanes  
Lead carbonates and sulfates  
Lead and Lead compounds  
Mercuric Oxide Batteries  
Ozone Depleting Substances  
Polybrominated Biphenyls (PBBs)  
Polybrominated Biphenyl Ethers (PBBEs)  
Polybrominated Biphenyl Oxides (PBBOs)  
Polychlorinated Biphenyl (PCB)  
Polychlorinated Terphenyls (PCT)  
Polyvinyl Chloride (PVC) – except for wires and cables, and certain retail packaging has been  
voluntarily removed from most applications.  
Radioactive Substances  
Tributyl Tin (TBT), Triphenyl Tin (TPT), Tributyl Tin Oxide (TBTO)  
2
Nickel finishes that release greater than 0.5 micro-grams/cm /week, measured according to EN  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QuickSpecs  
Technical Specifications  
HP ap5000 All-in-One (AiO) Point of Sale (POS) System  
1811:1998, are not used on any product surface designed to be frequently handled or touched  
by users.  
Packaging  
HP follows these guidelines to decrease the environmental impact of product packaging:  
Eliminate the use of heavy metals such as lead, chromium, mercury and cadmium in packaging  
materials.  
Eliminate the use of ozone-depleting substances (ODS) in packaging materials.  
Design packaging materials for ease of disassembly.  
Maximize the use of post-consumer recycled content materials in packaging materials.  
Use readily recyclable packaging materials such as paper and corrugated materials.  
Reduce size and weight of packages to improve transportation fuel efficiency.  
Plastic packaging materials are marked according to ISO 11469 and DIN 6120 standards.  
End-of-life Management Hewlett-Packard offers end-of-life HP product return and recycling programs in many geographic areas.  
and Recycling  
sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.  
The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each  
product type for use by treatment facilities. This information (product disassembly instructions) is posted  
recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP  
equipment.  
Hewlett-Packard  
For more information about HP's commitment to the environment:  
Corporate Environmental Global Citizenship Report  
Eco-label certifications  
ISO 14001 certificates:  
Copyright © 2012Hewlett-Packard Development Company, L.P.  
All rights reserved. Microsoft, Windows and Windows Vista are registered trademarks or trademarks of Microsoft Corporation in the  
U.S. and/or other countries. Intel, Celeron, and Core are trademarks of Intel Corporation in the U.S. and/or other countries.  
The information contained herein is subject to change without notice and is provided "as is" without warranty of any kind. The  
warranties for HP products are set forth in the express limited warranty statements accompanying such products. Nothing herein  
should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions  
contained herein.  
DA - 13540  
Worldwide — Version 13 — January 30, 2012  
Page 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Hamilton Beach Blender 59780R User Manual
Hamilton Beach Can Opener Sure Cut User Manual
HannsG Computer Monitor HSG 1073 User Manual
Hayter Mowers Lawn Mower RS102H User Manual
Heatcraft Refrigeration Products Air Conditioner CC CUBZTB User Manual
Hotpoint Clothes Dryer VTD00 User Manual
Huawei Network Router B260 User Manual
Hypertec Laptop Flextop vsn2 User Manual
Hypertec Mouse KEYB002HY User Manual
Icom Pet Fence AP 12 User Manual