Start Here
Important: Do not connect the USB cable until
Step 15 or the software may not install properly.
1
Follow the steps in order. If you have problems during setup, see Troubleshooting at the end of this Guide.
Remove all tape and cardboard
2
CAUTION: Make sure you
remove all packing material
or the device will not work
properly.
Locate components
3
ii
Itl
J
l
l
l
HP PSC
ii
i
i
t
t
lf
s
kia
control panel overlay (glossy
sticker, may be pre-attached)
i
i
çi
t
Windows CD
print cartridges
ti
l
ltl
ii
Macintosh CD
User Guide
l
l
Itl
J
l
ii
i
i
t
t
lf
ki
gi
b
oi
açi
t
ti
l
l
t
l
power cord and
adapter
HP Photosmart 2600/2700 series all-in-one
User Guide
* Purchased separately.
The contents of your box may differ.
USB cable*
HP PSC 1500 All-in-One series Setup Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the On button
6
After you press the On button, the green light
flashes, and then becomes solid. This may take up
to a minute.
On
Load plain white paper
7
b
d
a
c
Open access door
8
9
Lower the access door until it stops. Make sure
the print carriage moves to the right side.
Remove tape from both cartridges
Pull the pink tab to remove the tape from both print
cartridges.
CAUTION: Do not touch the copper-colored contacts or
retape the cartridges.
HP All-in-One • 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert the tri-color print cartridge
10
CAUTION: The device must be
On before you can insert the print
cartridge.
a Hold the tri-color print cartridge
with the blue HP logo on top.
b Place the tri-color print cartridge in
front of the left slot.
c Push the cartridge firmly into the slot
until it snaps into place.
Insert the black print cartridge
11
a Hold the black print cartridge with the
blue HP logo on top.
b Place the black print cartridge in front
of the right slot.
c Push the cartridge firmly into the slot
until it snaps into place.
d Close the access door.
4 • HP All-in-One
Download from Www.Somanuals.com. All Manuals Search And Download.
Align the print cartridges
12
After you insert the cartridges, a print cartridge alignment
page prints. (This may take a few minutes.)
a Lift the lid. Place the top of alignment page face down in the
right front corner of the glass. Close the lid.
b Press the Start Scan button.
After the On light stops blinking, alignment is complete.
Recycle or discard the alignment page.
Turn on your computer
13
14
a Turn on your computer, login if necessary, and then wait for
the desktop to appear.
b Close any open programs.
Choose the correct CD
Windows Users:
Macintosh Users:
a Insert the HP All-in-One
a Locate the HP All-in-One
Macintosh CD.
Windows CD.
b Follow the onscreen
b Continue to the next step.
instructions.
If the startup screen does not appear, double-click
My Computer, double-click the CD-ROM icon, and
then double-click setup.exe.
HP All-in-One • 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the USB cable
15
Windows Users:
Macintosh Users:
You may have to wait several minutes before you see
the onscreen prompt to connect the USB cable.
Connect the USB cable to the port on the back
of the HP All-in-One, and then to any USB port
on your computer.
Once the prompt appears, connect the USB cable to
the port on the back of the HP All-in-One, and then
to any USB port on your computer.
If you do not see these screens, see
Troubleshooting on the next page.
6 • HP All-in-One
Download from Www.Somanuals.com. All Manuals Search And Download.
Finish software installation
16
Windows Users:
Macintosh Users:
Follow the onscreen instructions. Complete the
Sign up now screen. Congratulations!
a Insert the HP All-in-One Macintosh CD.
b Double-click the HP All-in-One Installer
icon.
c Make sure you complete all screens,
including the Setup Assistant.
Congratulations!
Troubleshooting Software
Problem: (Windows only) You did not see the screen telling you when to connect
the USB cable.
Action: Remove, and then re-insert the HP All-in-One Windows CD. Refer to
Step 14.
Problem: (Windows only) The Microsoft Add Hardware screen appears.
Action: Click Cancel. Unplug the USB cable, and then insert the HP All-in-One
Windows CD. Refer to Steps 14 and 15.
Problem: (Windows only) The Device Setup Has Failed To Complete screen appears.
Action: Verify that the control panel overlay is firmly attached. Unplug the
device and plug it in again. Check all connections. Make sure the USB cable is
plugged into the computer. Do not plug the USB cable into a keyboard or non-
powered hub. Refer to Steps 4 and 15.
HP All-in-One • 7
Download from Www.Somanuals.com. All Manuals Search And Download.
*Q5888-90232*
*Q5888-90232*
Q5888-90232
Troubleshooting -
Control Panel
The first image shows how the control panel overlay looks after a successful setup. The second
image shows possible problems. See below for more information.
Correct:
Alerts:
1
2
3
E
4
Alerts:
Action:
The Check Paper light is flashing.
Check the input tray. The paper was not loaded correctly.
1
2
Reload the paper, and then press the Cancel/Resume button.
The Check Print Cartridge light is
flashing.
Make sure the tape was removed from the cartridges. Re-insert
the cartridge and then, close the door. Press the Cancel/
Resume button to continue.
An E in the Copies area.
Check for other lights to determine the problem. See the User
Guide for more information.
3
4
E
The Check Paper, Check Print
Cartridge, Start Copy areas are
flashing.
The overlay is not attached correctly. Refer to step 4. After
attaching, press the Cancel/Resume button to continue.
Printed on at least 50% total recycled fiber with at least 10% post-consumer paper.
© Copyright 2005 Hewlett-Packard Development Company, L.P. Printed in [].
Download from Www.Somanuals.com. All Manuals Search And Download.
|