Instructions–Parts List
STAINLESS STEEL OR CARBON STEEL
Air–Powered Gluttonr
307843ZAF
Pumps
EN
100 psi (0.7 MPa, 7 bar) Maximum Incoming Air Pressure
400 Series Pumps
400 psi (2.8 MPa, 28 bar) Maximum Fluid Working Pressure
Model 220663, Series D
Model 237008, Series A
Carbon steel pumps*
Model 220666, Series D
Model 237011, Series A
Stainless steel pumps*
Electro-polished for use with waterborne coatings
1200 Series Pumps
1200 psi (8 MPa, 83 bar) Maximum
Fluid Working Pressure
Model 220664, Series D
Model 237009, Series A
Carbon steel pumps*
Model 220667, Series D
Model 237012, Series A
Stainless steel pumps*
Electro-polished for use with waterborne coatings
2500 Series Pumps
2500 psi (17 MPa, 170 bar) Maximum Fluid
Working Pressure
Model 220665, Series D
Model 237010, Series A
Carbon steel pumps*
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
Model 220668, Series D
Model 237013, Series A
Stainless steel pumps*
Electro-polished for use with waterborne coatings
*See TECHNICAL DATA on pages 44 through 46
for a complete materials list.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Warning Symbol
Caution Symbol
WARNING
CAUTION
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
SKIN INJECTION HAZARD
Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also
cause serious injury.
D Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate
surgical treatment.
D Do not point the gun at anyone or at any part of the body.
D Do not put your hand or fingers over the spray tip.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the gun when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun trigger safety operates before spraying.
D Lock the gun trigger safety when you stop spraying.
D Follow the Pressure Relief Procedure on page 10 whenever you: are instructed to relieve pres-
sure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.
D Tighten all fluid connections before operating the equipment.
D Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Perma-
nently coupled hoses cannot be repaired; replace the entire hose.
D Use only Graco approved hoses. Do not remove the spring guard that is used to help protect the
hose from rupture caused by kinks or bends near the couplings.
307843
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
INSTRUCTIONS
D This equipment is for professional use only.
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest rated system component. Refer to the
Technical Data section on pages 44 through 46 for the maximum working pressure of this equip-
ment.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Do not use hoses to pull equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82_C (180_F) or below –40_C (–40_F).
D Do not lift pressurized equipment.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
D Never place your hands on or near the pump fluid inlet. Powerful suction could cause serious
bodily injury.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers or other body parts.
D Keep clear of all moving parts when starting or operating the equipment.
D Before servicing the equipment, follow the Pressure Relief Procedure on page 10 to prevent the
equipment from starting unexpectedly.
D Never operate the motor with the pump housing removed.
4 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D Ground the equipment and the object being sprayed. See Grounding on page 7.
D Proper hose grounding continuity is essential in maintaining a grounded spray/dispense system.
Check the electrical resistance of your air and fluid hoses at least once a week. If your hose does
not have a tag on it that specifies the maximum electrical resistance, contact the hose supplier or
manufacturer for the maximum resistance limits. Use a resistance meter in the appropriate range
for your hose to check the resistance. If the resistance exceeds the recommended limits, replace it
immediately.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D Keep the spray area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the spray area.
D Extinguish all open flames or pilot lights in the spray area.
D Do not smoke in the spray area.
D Do not turn on or off any light switch in the spray area while operating or if fumes are present.
D Do not operate a gasoline engine in the spray area.
HAZARDOUS FLUIDS
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Be sure all fluids and solvents used are chemically compatible with the wetted parts shown in the
TECHNICAL DATA for your pump model. Always read the fluid and solvent manufacturer’s litera-
ture before using the fluid or solvent in this pump.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
D Provide for safe piping and disposal of exhaust air.
D Secure the fluid outlet house tightly into the receiving container to prevent the hose from coming
loose and creating a fluid spill.
D Provide proper ventilation in accordance with accepted industry standards and government regula-
tions.
United States Government safety standards have been adopted under the Occupational Safety and Health Act. You
should consult these standards – particularly the General Standards, Part 1910, and the Construction Standards,
Part 1926.
307843
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Mounting the Pump
General Information
D The installation shown in Fig. 4 is only a guide for
selecting and installing system components. Con-
tact your Graco distributor for assistance in plan-
ning a system to suit your needs.
D 400 and 1200 Series Pumps: Mount the pump
with the accumulators in the top position as shown
in Fig. 1. The accumulators must be in the position
shown or the pump will not prime.
D See pages 38 through 43 for accessories and kits
available from Graco. Always use Genuine Graco
Parts and Accessories.
D Be sure the pump is securely bolted to its mounting
and that the mounting can support the weight of the
pump, hoses, and stress caused during operation.
D Use a thread sealant compatible with the fluid being
pumped on all male pipe threads. Tighten all con-
nections firmly to avoid air or fluid leaks.
D The outlet manifold can be removed and turned 180
degrees to change the direction of the outlet and
ease installation, as shown in Fig. 3.
D Reference numbers and letters in parentheses in
the text refer to the figure illustrations.
accumulators
02321
Fig. 1
6 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
D Air Compressor: Follow the manufacturer’s recom-
Grounding
mendations.
WARNING
D Spray gun or dispensing valve: Obtain grounding
through connection to a properly grounded fluid
hose and pump.
This pump must be grounded. The steps for
grounding may differ from the way you ground
other pumps. Carefully read and follow these
grounding instructions. See FIRE AND EXPLO-
SION HAZARD on page 5 before you operate the
pump.
D Fluid supply container: Follow the local code.
D Object being sprayed: Follow the local code.
Static electricity is created by the high-velocity flow of
fluid through the pump and hose. If every part of the
equipment is not properly grounded, sparking may oc-
cur. To reduce the risk of static sparking, ground the
pump and all other equipment used or located in the
pumping area. Check your local electrical code for de-
tailed grounding instructions for your area and type of
equipment. Ground all of the following equipment:
D All solvent pails used when flushing: Follow the
local code. Use only metal pails, which are conduc-
tive. Do not place the pail on a non-conductive
surface, such as paper or cardboard, which inter-
rupts the grounding continuity.
To ground the pump: Loosen the grounding lug lock-
nut (W) and washer (X). Insert one end of a 12 ga (1.5
mm@) minimum ground wire (Y) into the slot (Z) of the
grounding lug, and tighten the locknut securely. Con-
nect the clamp end of the ground wire to a true earth
ground. To order a ground wire and clamp, order Part
No. 222011.
D Pump: use a ground wire and clamp as shown in
Fig. 2.
D Fluid and air hoses: use only grounded hoses with
a maximum of 500 feet (150 m) combined hose
length to ensure grounding continuity.
grounding lug
Y
W
X
Z
02322
Fig. 2
307843
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3. Install a control device, such as a gun, dispensing
Connect the Fluid Lines
valve, or shutoff valve, on the grounded fluid
hose (H).
1. Use grounded fluid hoses.
a. The pump fluid outlet (J) on the 400 and
1200 Series Pumps is 1 npt(f) .
Connect the Fluid Suction Line
b. The pump fluid outlet (J) on the 2500 Series
CAUTION
The pump must be suction fed in order to operate
properly. Pressure feeding or exceeding 15 psi (104
kPa, 1.04 bar) maximum fluid inlet pressure may
cause premature bellows seal failure.
Pump is 3/4 npt(f).
2. Install a fluid filter (F) and drain valve (E) near the
fluid outlet. See Fig. 3.
WARNING
A fluid drain valve (E) is required in your system to
relieve pressure in the fluid outlet hose (H) if the
hose becomes plugged. See Fig. 3. Install a drain
valve close to the pump’s fluid outlet. The drain
valve reduces the risk of property damage or
serious bodily injury, including splashing in the eyes
or on the skin, or contamination from hazardous
fluids.
Connect the fluid suction hose (S) to the pump fluid
inlet (M). See Fig. 4.
D The pump fluid inlet (M) is 1.25 npt(f).
D The maximum suction lift is 15 ft (4.57m) for the
400 Series and 1200 Series Pumps, and 6 ft (1.83
m) for the 2500 Series Pump.
J
H
F
E
M
WARNING
SUCTION HAZARD
02325
Never place your hands on or near the pump fluid
inlet. Powerful suction could cause serious bodily
injury.
Fig. 3
8 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
6. Install one bleed-type master air valve (C) down-
Connect the Air Lines
stream from the air regulator and use it to relieve
trapped air. Locate the other master air valve up-
stream from all air line accessories and use it to
isolate the accessories during cleaning and repair.
1. Install the air line accessories to the left of the
pump as shown in Fig. 4. Mount these accessories
on the wall or on a bracket. Be sure the air line
supplying the accessories is grounded.
7. Install an air line filter (A) to remove harmful dirt
and moisture from your compressed air supply.
2. Install a flexible air hose between the accessories
and the 1/2 in. npt(f) air inlet (G). Use a minimum
1/2 in. ID air hose.
8. Install a grounded air supply line (P) with a mini-
mum 1/2 in. ID. See Fig. 4.
3. Install an air line lubricator (B) upstream from the
pump air inlet for automatic pump lubrication.
Ventilate the Air Exhaust
4. Install a pump runaway valve (T) to sense when
the pump is running too fast and shut off the air
supply to the motor. To order a pump runaway
valve, order Part No. 224040.
WARNING
Improper handling of hazardous fluids or inhaling
their vapors can cause serious bodily injury, even
death. For your safety, it is imperative that you read
all product warning labels and Material Safety Data
Sheets (MSDS) for the fluids you are using. An
MSDS can be obtained from your fluid suppliers. It
is also important that you read and understand the
warnings and precautions regarding HAZARDOUS
FLUID HAZARD on page 5 before you operate.
5. Install an air regulator (D) to control air inlet pres-
sure.
WARNING
A bleed-type master air valve (C) is required in
your system to relieve air trapped between this
valve and the pump after the air regulator is closed.
Trapped air can cause the pump to cycle unexpect-
edly, which could result in serious bodily injury,
including splashing in the eyes, injury from moving
parts, or contamination from hazardous fluids.
All systems using hazardous fluid in enclosed
areas or within buildings should have a properly
designed and installed ventilation system. Consult
your local building code and other industrial and
governmental standards for proper design criteria.
N
J
F
H
T
L
G
P
D
C
B
M
K
E
C
A
S
KEY
A
B
C
D
E
F
Air line filter
Air line lubricator
Bleed-type master air valve
Air regulator
Fluid drain valve
Fluid filter
K
Main air line
Ground wire
L
M Intake manifold
N
P
R
S
T
Glutton pump
Grounded air line
Fluid supply
Fluid suction hose
Runaway valve
R
G Pump air inlet
H
J
Grounded fluid line
Outlet manifold
02323
Fig. 4
307843
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Pressure Relief Procedure
Start and Adjust the Pump
NOTE: Check all fittings to be sure they are tight. Be
sure to use a thread sealant compatible with the fluid
being pumped on all male pipe threads.
WARNING
The system pressure must be manually relieved to
prevent the system from starting or spraying acci-
dentally. To reduce the risk of an injury from acci-
dental spray from the gun, splashing fluid, or
moving parts, always follow the Pressure Relief
Procedure whenever you
1. Place the suction hose (S) in the fluid to be
pumped. See Fig. 5.
2. Close the fluid drain valve (E).
3. With the air regulator (D) closed, open both bleed-
type master air valves (C).
D are instructed to relieve the pressure
D Stop spraying
4. Open the fluid control device while continuing with
the following steps.
5. Slowly open the air regulator (D). Adjust it until the
pump runs smoothly.
D Check or service any of the system equipment
D install or clean the spray nozzle.
6. Allow the pump to cycle slowly until all air is
pushed out of the lines (the fluid will be flowing in a
steady stream from the fluid outlet) and the pump
is primed.
1. * Engage the spray gun or dispensing valve safety
latch.
2. Shut off the air supply.
3. * Disengage the gun or dispensing valve safety
latch.
4. * Hold a metal part of the gun or valve firmly to a
grounded metal waste container and trigger it to
relieve the fluid pressure.
5. * Engage the safety latch again.
6. Open the pump drain valve (required in system),
and have a container ready to catch the drainage.
WARNING
To reduce the risk of component rupture, which
could cause serious bodily injury, never exceed
100 psi (0.7 MPa, 7 bar) air supply pressure to the
pump. Read the warning section EQUIPMENT
MISUSE HAZARD on page 4.
7. Leave the drain valve open until you are ready to
spray again.
*
Applies only when using a spray gun or dispensing
valve.
If you suspect that the spray tip, nozzle, or hose is
clogged or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
hose end coupling and relieve pressure gradually, then
loosen completely, then clear the tip, nozzle, or hose
obstruction.
Flush the Pump Before First Use
WARNING
To reduce the risk of fluid injection injury, static
sparking and splashing, read and follow Flushing
Safety under FIRE OR EXPLOSION HAZARD on
page 5.
The pump was tested with lightweight oil, which is left
in to protect the pump parts. If this solution could con-
taminate the fluid you are pumping, flush it thoroughly
with a compatible solvent. To start the pump, follow the
procedure in Start and Adjust the Pump, below.
10 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
7. If you are flushing:
CAUTION
a. Run the pump long enough to thoroughly clean
the pump and hoses.
Never allow the pump to run dry of fluid. A dry pump
will accelerate to a high speed, possibly damaging
itself. If your pump accelerates quickly, or is running
too fast, stop it immediately and check the fluid
supply. If the supply is empty and air has been
pumped into the lines, refill the container and prime
the pump and lines with fluid, or flush and leave filled
with compatible solvent. Be sure to eliminate all air
from the system. A Pump Runaway Valve, Part No.
224040, is available.
b. Close the fluid control device and air regulator
(D).
c. Remove the suction hose (S) from the solvent
and place it in the fluid to be pumped.
8. If you are going to use the pump:
a. Start the pump. Be sure the suction hose is in
the supply container.
b. If you are using this pump to spray fluid, re-
lieve the pressure, then install a spray tip in
the gun. Trigger the gun into a grounded metal
waste container to prime the hose. Adjust the
pump pressure just enough to completely at-
omize the fluid. Higher pressures cause pre-
mature spray tip and pump wear.
9. If you are shutting down the pump:
a. Flush the pump before shutting down, espe-
cially if pumping a material that will set up.
b. Remove the suction hose from the fluid con-
tainer and run the pump until the fluid is forced
out of the system, then shut off the air supply
immediately.
WARNING
PRESSURIZED EQUIPMENT HAZARD
To reduce the risk of a serious injury whenever you
are instructed to relieve pressure, follow the Pres-
sure Relief Procedure on page 10.
c. Relieve the pressure.
WARNING
PRESSURIZED EQUIPMENT HAZARD
To reduce the risk of a serious injury whenever you
are instructed to relieve pressure, follow the Pres-
sure Relief Procedure on page 10.
c. In a direct supply system, the pump will start
and stop as the spray gun, dispensing valve,
or fluid outlet valve is opened and closed.
d. In a circulating system, the pump runs continu-
ously and speeds up or slows down as supply
demands until the air supply is shut off.
d. Refer to the Maintenance instructions on
page 14.
C
D
C
E
S
02323
Fig. 5
307843 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Relieve the pressure, and check all probable causes
before disassembling the pump.
WARNING
PRESSURIZED EQUIPMENT HAZARD
To reduce the risk of a serious injury whenever you
are instructed to relieve pressure, follow the Pres-
sure Relief Procedure on page 10.
SYMPTOM
PROBABLE CAUSE
TEST PROCEDURE
REMEDY
1. Pump will not
prime
Air is getting into the intake
housing:
a. Replace o-ring.
See page 15.
a. Defective o-ring (19) on in-
take manifold or accumu-
lator
b. Tighten, or add
sealant to threads
b. Suction hose/tube not
sealed
2. Pump will not
run
a. Air supply turned off
b. Fluid valve turned off
a. Turn air supply on
b. Turn fluid supply
valve on
c. Minimum air pressure
on regulator 25 psi (175
kPa, 1.95 bar), depend-
ing on fluid being
c. Air pressure regulator
set too low
c. Increase air pressure
regulator adjustment
pumped
d. Remove tube ends from
hose studs. With air
supply on, alternately
plug tube ends. If pump
runs, remove pilot
d
Pilot valve assemblies
worn
d. Repair or replace pilot
valve assembly. See
page 22.
valves, inspect
e. Check for air coming
from exhaust when
e. Air control valve
defective
e. Repair or replace air
control valve. See page
20.
pump is not running
f. Air piston quad ring (28)
worn
f. Replace quad ring. See
page 18.
12 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
SYMPTOM
PROBABLE CAUSE
TEST PROCEDURE
REMEDY
3. Pump runs but
does not main-
tain constant
pressure
a. Air in fluid line
a. Check for spitting at
fluid line outlet
a. Bleed fluid line until con-
stant flow is
obtained
b. Air line too small
b. Install larger air line,
minimum size 1/2 in.
c. Obstructed or worn ball
(57) and seat (49)
c. Pump fast cycles on
one end of stroke
indicates that side is by-
passing
c. Remove, clean, and in-
spect seat, ball, and ball
guide (56). Replace if
worn. See page 15.
d. Worn fluid piston (17)
and/or piston seal (13)
d. Pump fast cycles on
one end of stroke
indicates that side is by-
passing
d. Replace piston and/or
seal. See page 16.
e. Air control valve
mufflers (38) plugged
e. Check for slow air flow
at muffler
e. Remove and clean muf-
flers
f. Air control valve dirty or
worn
f. Repair or replace air
control valve. See page
20.
g. Lack of lubrication
h. Dirty air passages
g. Pump reacts slowly
g. Adjust lubricator
h. Check for sluggish air
control valve operation
h. Clean air passages; do
not enlarge orifices.
Empty air line filter and/
or control valve filter
(40q). See step 5 in Dis-
assembly on page 20.
4. Paint dripping
externally
a. Ruptured bellows seal
(14)
a. Check for presence of
paint around piston
shaft (15)
a. Replace bellows seal.
See page 16. Be sure
to suction feed, not
pressure feed, pump.
Maximum fluid inlet
pressure is 15 psi (104
kPa, 1.04 bar)
around piston
rod
307843 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Flush the Pump With Compatible Solvent
Tighten Threaded Connections
WARNING
To reduce the risk of fluid injection injury, static
sparking and splashing, read and follow Flushing
Safety under FIRE OR EXPLOSION HAZARD on
page 5.
1. Before each use, check all hoses for wear or dam-
age and replace as necessary. Be sure all
threaded connections are tight, and leak-free.
2. At least every six months, check and tighten all
threaded connections, including manifold screws,
clamps, plugs, and valve screws.
1. Flush often enough to prevent fluid from drying in
the pump and damaging it.
2. Always flush before storing.
a. If you are pumping water-based fluid, first flush
the pump with water, then with mineral spirits
or a compatible oil-based solvent.
Check and Service the Lubricator, Regula-
tor, and Filter
b. Leave the mineral spirits or oil-based solvent
in the pump to protect the pump parts from
corrosion.
Check and service according to the instructions sup-
plied with them. See Manual 308169 for oil recommen-
dations.
3. Be sure to eliminate all air from the system.
14 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Disassembly
Repairing the Ball Check Valves
NOTE: Parts marked with an asterisk are included in a
repair kit, for example, (54*). See pages 38 and 39 for
repair kit part numbers. Use all the parts in the kit for
the best results.
1. Relieve the pressure.
Disassembly
WARNING
PRESSURIZED EQUIPMENT HAZARD
To reduce the risk of a serious injury whenever you
are instructed to relieve pressure, follow the Pres-
sure Relief Procedure on page 10.
1. Relieve the pressure.
WARNING
PRESSURIZED EQUIPMENT HAZARD
To reduce the risk of a serious injury whenever you
are instructed to relieve pressure, follow the Pres-
sure Relief Procedure on page 10.
2. Loosen the tube nuts (A) and remove the outlet
manifold (50). Unscrew the connectors (51). Re-
move the o–ring (52). See Fig. 6.
2. Disconnect the air and fluid lines, remove the
pump from its mounting, and place it on a bench.
3. Remove the cap (53) from each side of the outlet
housing (33). See Fig. 6.
3. Remove the screws (34), washers (35), outlet
housing (33), piston seal (13*) and retaining plate
(12). Remove the o–ring (18). Repeat on the other
side of the pump.
4. Remove the ball guide (56), ball (57), valve seat
(49), and o-ring (48*) on each side of the outlet
housing.
5. Inspect the ball stop (55) inside the cap (53) for
wear. Remove o–ring (54). Replace if necessary.
4. Holding the screw (16) on one side of the pump,
loosen the screw three or four turns on the oppo-
site side of the pump, using a socket and breaker
bar.
6. Clean all parts and inspect for wear or damage.
Replace as needed.
Assembly
5. Remove the piston (17) by grasping it with your
hand and and hit screw (16) with a plastic mallet to
drive piston loose from shaft. Remove screw (16)
and piston (17).
1. Lubricate the o-rings (48*) and place one in the
groove on each valve seat (49).
2. Install the valve seat (49) with the o-ring (48) fac-
ing down, ball (57), and ball guide (56) into each
outlet housing (33).
6. Remove the screws (32), washers (46 or 61), and
inlet manifold (47). Remove o–rings (19).
NOTE: Stainless steel seats are reversible.
3. Lubricate the o-rings (54*) and the cap (53)
threads. Place one o-ring on each cap. Screw the
caps into the housing and torque them to 55 to 85
ft-lb (75 to 115 NSm).
7. Remove the intake housing (36), bellows (14*),
and retaining plate (20).
NOTE: On stainless steel pumps (Models 220666
through 220668 and Models 237011 to 237013), apply
anti-seize lubricant to the threads of the cap (53).
8. Holding the piston shaft (15) flats with a wrench,
remove the remaining screw (16).
Repairing the Fluid Piston and Seal
NOTE: Parts marked with an asterisk are included in a
repair kit, for example, (52*). See pages 38 and 39 for
repair kit part numbers. Use all the parts in the kit for
the best results.
9. Repeat steps 6 and 7 on the opposite end of the
pump. Clean all parts and inspect for wear or dam-
age. Replace as needed.
307843 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Assembly
6. Apply 10 psi air to move the piston to one side and
hold it there. Replace the o–ring (18*) in the
groove in the tapered side of the retaining plate
(12).
1. Slide the retaining plate (20), bellows (14*), and
intake housing (36) onto the piston shaft (15). Do
not force the bellows. Repeat on the other side.
Grease the oulet housing groove and set the nylon
seal (13) inside the groove. Carefully tip the hous-
ing (33) onto the inlet housing. Be sure the flat side
of the retaining plate (12) faces the piston seal.
Secure with the four screws (34) and washers
(35).
CAUTION
To avoid damaging the bellows (14), do not force it
onto the shaft. The bellows will press into place when
the piston (17) is secured.
Increase the air pressure to about 50 psi until the
pump cycles and the piston drives to the other
side.
2. Install the piston (17) on the shaft (15) and secure
it with the screw (16). Repeat on the opposite end
of the pump.
Reduce the air pressure to 10 psi to hold in posi-
tion. Repeat the seal installation pattern.
3. Using a socket and breaker bar, torque one screw
(16) to 40 to 50 ft-lb (54 to 67 NSm), then repeat
with the other screw.
Increase the air pressure to 50 psi again to cause
the pump to cycle again and form the seal on the
first side.
4. Grease and install an o-ring (19*) in each inlet.
Install inlet manifold (47) with screws (32) and
washers (46 or 61). Don’t torque screws yet.
NOTE: Torque the screws, on 400 and 1200 Series
pumps, to 40 to 50 ft-lb (54 to 68 N-m). Torque the
screws on the 2500 Series pump, to 35 to 40 ft-lb (47
to 54 N-m).
CAUTION
To avoid loosening the piston stud (30) during disas-
7. Torque the inlet manifold screws (32) to 7.4 to 12.5
ft-lb (10 to 17 N-m).
sembly, do not overtighten the screws (16).
NOTE: If using a formed UHMWPE seal, proceed to
step 5. If using a flat nylon seal, proceed to step 6.
8. Replace the o-ring (52*) in each outlet manifold
connector (51) and lubricate the threads. Install the
outlet manifold (50), torquing the connectors to 55
to 85 ft-lb (75 to 115 NSm).
5. Grease and install the o-ring (18*) in the groove in
the tapered side of the retaining plate (12). Grease
the outlet housing (33) and install the piston seal
(13*) and retaining plate (12). Be sure the flat side
of the retaining plate faces the piston seal. Secure
with the four screws (34) and washers (35).
NOTE: On stainless steel pumps (Models 220666
through 220668 and Models 237011 to 237013), apply
anti-seize lubricant to the threads of the connector
(51).
16 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
20
1 53
55
8
14*
54*
36
17
2
16
5
57
56
49
19*
47
18*
12
13*
48
8
58
46 or 61
7
16 5
50
32
6
73
33
35
3 34
52*
51
1
8
4
A
NOTES:
1
Lubricate threads. Torque to
55 to 85 ft-lb (75 to 115 NSm)
2
3
Fit o-ring into groove
400 & 1200 Series pumps: Torque to
40 to 50 ft-lb (54 to 68 NSm)
2500 Series pumps: Torque to 35
to 40 ft-lb (47 to 54 NSm)
223111 & 220487 :Torque to 110 to 120 ft-lb (149 to 162 NSm)
220491 & 220485: Torque to 140 to 150 ft-lb (190 to 203 NSm)
See model and part number for specification.
4
5
6
7
Torque to 40 to 50 ft-lb (54 to 67 NSm)
Torque to 7.4 to 12.5 ft-lb (10 to 17 NSm)
Item 61 is used on stainless steel models only
15
02326
On stainless steel pumps (Models 220666 through 220668 and Models 237011
to 237013), apply anti-seize lubricant to the threads.
8
Fig. 6
307843 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Assembly
Repairing the Air Motor and Piston
NOTE: Parts marked with an asterisk are included in a
repair kit, for example, (23*). See pages 38 and 39 for
repair kit part numbers. Use all the parts in the kit for
the best results.
1. Apply lithium base grease to all packings, seals,
and the inside of the air motor cylinder (27) before
assembling.
Disassembly
1. Relieve the pressure.
2. If the piston shafts (15) were removed from the
piston stud (30), apply high strength sealant (such
as Loctiter) to the threads of the piston stud, and
assemble as shown in Fig. 7.
WARNING
PRESSURIZED EQUIPMENT HAZARD
To reduce the risk of a serious injury whenever you
are instructed to relieve pressure, follow the Pres-
sure Relief Procedure on page 10.
3. Install the quad ring (28*) in the groove on the pis-
ton (29). Install the piston assembly (A) into the air
motor cylinder (27).
2. Disassemble the pump as instructed under Re-
pairing the Fluid Piston and Seal.
3. Remove the screws (3 & 4), washers (46), nuts
(1), and lockwashers (2) from the cylinder cap
(25). See Fig. 7.
4. Install a u-cup (23*) into each of the cylinder caps
(25). The lips of the u-cup must face in, towards
the center of the pump, as shown in Fig. 8.
4. Remove the pump from the mounting bracket (44).
5. Remove the cylinder cap (25) from each end of the
air motor. If the hoses aren’t disconnected or the
pilot valves removed, be careful not to pull on the
hoses when removing the caps.
5. If the bearings (22) were removed, install a bearing
into each cylinder cap (25). Press fit the bearing to
flush, using an arbor press.
CAUTION
The shaft wiper (21) and bearing (22) are meant to
remain in place. Remove only to replace. Removal
will damage them.
6. Install a shaft wiper (21) into each cylinder cap
(25) with the brass part of the wiper facing out,
away from the center of the pump, as shown in
Fig. 8. Carefully press the wiper into place, taking
care to avoid damaging the brass piece.
6. Remove the shaft wiper (21) and bearing (22); only
if they need to be replaced, and u-cup (23*) from
each of the cylinder caps (25). Use a 0.875 in. di-
ameter shaft to remove the bearing.
7. Install an o-ring (26*) into the groove in each of the
cylinder caps (25). Slide a cylinder cap (25) onto
each end of the air motor. Align flat edges with air
valve.
7. Remove the piston assembly (A) from the air mo-
tor cylinder (27). Remove the seal (28).
8. Do not remove the piston shafts (15) unless re-
placement is necessary as a high strength sealant
was used on the threads. If the rods must be re-
moved, heating the joint to 300_ F will ease disas-
sembly. Place wrenches on the flats of the piston
shaft to disconnect them from the piston stud (30).
8. Secure the mounting bracket (44) and cylinder
caps (25) on the pump with the screws (3 and 4),
washers (46), nuts (1), and lockwashers (2). Tor-
que the screws oppositely and evenly to 7.4 to
12.5 ft-lb (10 to 17 NSm).
9. Clean all parts and inspect for wear or damage.
Replace as needed.
18 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
NOTES:
1
Take care not damage tubes when re-
moving cap (25)
2
3
Apply high-strength sealant to threads
Torque to 7.4 to 12.5 ft-lb (10 to 17 NSm)
Press fit to flush
4
5
1
Press fit to bottom
2
30
28*
REF
29
15
1
2
26*
27
A
28*
26*
46
25
23
4
22
5
21
4
3
44
3
3
02327
Fig. 7
307843 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
5. Thread one spool (40c) onto the stem (40d) and
Repairing the Air Control Valve
insert it into the center housing (40a); be careful
not to dislodge the u-cups (40j) and retainers
(40e). Thread the other spool onto the stem. With
wrenches on the flats of the spools, apply oppos-
ing force and tighten until snug; 7 to 13 in-lb (0.79
to 1.47 NSm). Do not overtighten.
NOTE: Air Valve and Pilot Valve Repair Kit 220656 is
available. See page 38 to order. Parts included in the
kit are marked with an asterisk, for example, (40p*).
Use all the parts in the kit for the best results.
Disassembly
1. Relieve the pressure.
WARNING
PRESSURIZED EQUIPMENT HAZARD
To reduce the risk of a serious injury whenever you
are instructed to relieve pressure, follow the Pres-
sure Relief Procedure on page 10.
CAUTION
Do not overtighten the spools (40c) as this can
shear the spool threads.
2. Cut a small slit in the tube ends (72*, 42*, 40p*)
and disconnect them from the pilot valve fittings
(5h), air valve tees (40n), and barb fittings (40s).
See Fig. 8.
6. Replace the gasket (40f*) in each end housing
(40b) and the o-ring (40g*) on each end housing
shoulder.
3. Remove the valve end housings (40b) by unscrew-
ing the screws (40k) and nuts (40m).
7. With the mufflers facing down, install the end
housings (40b), onto the center housing (40a); be
careful not to move the spool and dislodge the u-
cups (40j) and retainers (40e). Secure the end
housings with the four screws (40k) and nuts
(40m), torquing them to 2.2 to 3.7 ft-lb (3 to 5
NSm).
4. Center the valve spools (40c) in the housing (40a).
Remove the spools and stem (40d) by applying
opposing force with wrenches on the spool (40c)
flats.
5. If the air filter (40q) needs cleaning or replace-
ment, unscrew the filter housing (40r) and remove
the filter. To clean them, soak the filter housing and
the filter in solvent until they are clean. Blow them
dry with low pressure air [under 30 psi (207 MPa,
2.1 bar)]. Press fit the filter into the housing, using
40 to 60 lb (18 to 27 kg) of force. Refer to Fig. 8.
Apply sealant to the filter housing threads and turn
it into the center housing (40a).
CAUTION
If mufflers (38) are replaced, they must be installed
with the lock rings (39) to avoid damage to the spool
and o-rings during operation.
Assembly
1. Apply lithium-base grease to all o-rings, u-cups,
gaskets and to the complete spool assembly be-
fore installing them.
8. Replace the two o-rings (40h*) in the center hous-
ing (40a).
2. Remove the seal retainers (40e) from each side of
the center housing (40a). Replace the u-cup (40j*),
with the lips facing into the housing. Install the re-
tainers with the flat side facing into the housing.
9. Install the air valve on the pump with the four cap
screws (43). Torque them alternately and evenly to
2.2 to 3.7 ft-lb (3 to 5 NSm).
3. Replace the spools (40c) if damaged. Replace the
o-ring (40h*) and u-cup (40i*) on each spool, being
sure to seat them in the grooves. Install the u-cup
with the lips facing towards the housing (40a).
10. Connect the new tubes (72*, 42*, 40p*) to the pilot
valve fittings (5h), air valve tees (40n), and barb
fittings (40s), as shown in Fig. 8.
4. Apply medium strength thread sealant to the spool
stem (40d) threads. Remove the excess sealant.
20 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
5h
40p
*72
5h
40h REF
1
43
40p REF
42*
5
40r
40s
40n
40m
40p
1
2
3
40q
40h*
40a
3
*40j
40e
40d
4
*40i
3
40k
NOTES:
1
2
3
4
3
Torque to 2.2 to 3.7 ft-lb (3 to 5 NSm)
40c
Press fit using 40 to 60 lb (18 to 27 kg) force
Lubricate with lithium-base grease
*40h
3
3
*40f
3
*40g
Apply medium strength sealant to threads.
Torque to 0.58 to 1.1 ft-lb (0.79 to 1.47
NSm)
40b
3
5
Apply sealant to threads
40n
02328
Fig. 8
307843 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Assembly
Repairing the Pilot Valve
NOTE: Air Valve and Pilot Valve Repair Kit 220656 is
available. See page 38 to order. Parts included in the
kit are marked with an asterisk, for example, (5j*). Use
all the parts in the kit for the best results.
1. Apply lithium base grease to the inside and outside
of the air valve (5b), and to the o-rings and seals.
2. Install the o-ring (5e*), being sure to completely
seat it on the flat in the valve housing (5d). Install
the long end of the valve stem (5a) into the hous-
ing.
Disassembly
1. Relieve the pressure.
3. Install the small spring (5g) over the valve stem
(5a), the air valve (5b) over the spring, and the
larger spring over the air valve.
WARNING
PRESSURIZED EQUIPMENT HAZARD
To reduce the risk of a serious injury whenever you
are instructed to relieve pressure, follow the Pres-
sure Relief Procedure on page 10.
4. With the copper gasket (5i*) in place on the valve
cap (5c), screw the cap onto each of the valve
housings (5d). Torque the cap to 7.4 to 12.5 ft-lb
(10 to 17 NSm).
2. Unscrew the valve cap (5c) from each of the valve
housings (5d) and remove the parts. Clean and
inspect the parts for damage. See Fig. 9.
3. To replace the rod seal (5j*):
a. Cut a small slit in the tube ends (72* and 42*)
and disconnect them from the pilot valve fit-
tings (5h) and air valve tees (40n).
b. Unscrew the cap screws (37) and remove the
pilot valve housings (5d). Grease the rod seals
(5j*) and install one on each side of the pump.
c. Secure the pilot valve housings (5d) to the
pump with the cap screws (37).
d. Connect the new tubes (72* and 42*) to the
pilot valve fittings (5h) and air valve tees (40n).
22 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
5d
3
5j*
5h
3
5e*
5a
5g
3
5b
5f
5i*
1
5c
*72
5h
*42
2
37
NOTES:
1
2
3
Torque to 7.4 to 12.5 ft-lb (10 to 17 NSm).
Torque to 2.2 to 3.7 ft-lb (3 to 5 NSm).
5h
40n
Lubricate with lithium-base grease.
02329
Fig. 9
307843 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
400 Series Carbon Steel Pumps
Model 220663, Series D
Model 237008, Series A
23*
22
53
31
32
21
20
55
54*
36
17
19*
57
56
16
14*
18*
12
49
13*
48*
58
19*
47
46
32
52*
33
35
34
1
2
52*
51
73
26*
50
29
27
30
28*
26*
15
25
46
47
4
71
1
2
64
44
3
02332
24 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref.
No.
400 Series Carbon Steel Pumps
Model 220663, Series D
Part No. Description
Qty.
Model 237008, Series A
27
183097
107160
183355
183229
181998
108768
CYLINDER, air motor
1
1
1
1
2
Ref.
No.
28*
29
30
31
32
QUAD RING; buna-N
PISTON, air motor
STUD
ACCUMULATOR
SCREW, cap, hex hd;
M8 x 1.25 x 16
HOUSING, pump outlet
SCREW, cap, hex hd;
M12 x 1.75 x 100
WASHER, lock
HOUSING, pump intake
SCREW, cap, hex sch;
M5 x 0.8 x 12
Part No. Description
Qty.
1
2
3
108712
104572
108786
NUT, hex; M8 x 1.25
8
8
WASHER, spring lock
SCREW, cap, hex hd;
M8 x 1.25 x 130
2
6
8
2
4
5
108711
221133
SCREW, cap, hex hd;
M8 x 1.25 x 120
PILOT VALVE ASSY
See page 37 for parts
PLATE, retaining
SEAL, piston; UHMWPE
(for pump Model 220663 only)
SEAL, piston; Nylon
(for pump Model 237008 only)
SEAL, bellows; polypropylene
SHAFT, piston
33
34
181846
108654
8
8
2
2
2
35
36
37
107541
181847
107100
12
13*
181953
181978
2
4
2
2
188177
38
39
40
107189
107190
220902
MUFFLER
2
2
2
RING, lock; 1/2 – 14 npt
AIR CONTROL VALVE ASSY
See page 36 for parts
TUBE, 0.25 in. (6.35 mm) O.D.;
polyurethane
SCREW, cap, hex hd;
M5 x 0.8 x 20
BRACKET, mounting
WASHER, flat
INTAKE MANIFOLD
O-RING; PTFE
SEAT, valve
MANIFOLD
14*
15
16
180243
181951
108652
1
1
SCREW, cap, hex hd;
M10 x 1.5 x 50
42{
183384
108787
2
17
189432
PISTON, pump;
17–4 PH stainless steel
O-RING; PTFE
O-RING; PTFE
PLATE, retaining; stainless steel
WIPER, shaft
BEARING
U-CUP; buna-N
CAP, cylinder
43
2
2
4
2
2
2
2
2
2
4
1
10
1
2
2
1
2
4
2
2
2
2
2
2
1
1
1
18*
19*
20
21
22
23*
25
26*
108824
108825
181967
108713
183228
108158
183098
108874
44
46
47
48*
49
50
51
52*
53
54*
55
56
57
58
59
60
64
71
72{
181950
108788
220486
103341
181947
220485
108648
107098
181949
108822
181976
181845
107167
108643
104582
104029
183429
179944
179861
CONNECTOR, straight thread
O-RING; PTFE
CAP
O-RING; buna-N
60
O-RING; PTFE
59
72{
40
STOP, ball; stainless steel
GUIDE, ball; stainless steel
BALL; stainless steel
PLUG, boss
WASHER, tab
LUG, grounding
LABEL, warning
LABEL, warning
TUBE, 0.245 in. (6.35 mm) O.D.;
37
1
polyurethane
SEAL, hydraulic
1
2
73
16F143
5
*
Parts included in Repair Kits 220949 (for pump
Model 220663); and 237014 (for pump Model
237008), which may be purchased separately.
43
42{
39
38
{ Parts included in Repair Kit 220656, which may be
purchased separately.
02333
See pages 38 – 40 for description of all Repair Kits,
Optional Repair Kits, and Conversion Kits available.
307843 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
400 Series Stainless Steel Pumps
Model 220666, Series D
Model 237011, Series A
23*
22
31
32
21
53
20
55
54*
36
17
19*
57
16
14*
18*
56
12
49
13*
48*
58
19*
47
46
32
52*
33
35
34
1
2
52*
51
73
26*
50
27
30
28*
29
15
26*
25
61
4
47
71
1
2
64
3
44
02332
26 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref.
No.
400 Series Stainless Steel Pumps
Model 220666, Series D
Model 237011, Series A
Ref.
Part No. Description
Qty.
27
183097
107160
183355
183229
220971
108791
CYLINDER, air motor
1
1
1
1
2
28*
29
30
31
32
QUAD RING; buna-N
PISTON, air motor
STUD
ACCUMULATOR
SCREW, cap, hex hd;
M8 x 1.25 x 16
HOUSING, pump outlet
SCREW, cap, hex hd;
M12 x 1.75 x 100
WASHER
HOUSING, pump intake
SCREW, cap, hex sch;
M5 x 0.8 x 12
No.
Part No. Description
Qty.
1
2
3
108712
104572
108786
NUT, hex; M8 x 1.25
8
8
WASHER, spring lock
SCREW, cap, hex hd;
M8 x 1.25 x 130
2
6
8
2
4
5
108711
221133
SCREW, cap, hex hd;
M8 x 1.25 x 120
PILOT VALVE ASSY
See page 37 for parts
PLATE, retaining
SEAL, piston; UHMWPE
(for pump Model 220666 only)
SEAL, piston; Nylon
(for pump Model 237011 only)
SEAL, bellows; polypropylene
SHAFT, piston
33
34
181864
108793
8
8
2
2
2
35
36
37
111449
181865
107100
12
13*
181974
181978
2
4
2
2
188177
38
39
40
107189
107190
220902
MUFFLER
2
2
2
RING, lock; 1/2 – 14 npt
AIR CONTROL VALVE ASSY
See page 36 for parts
TUBE, 0.25 in. (6.35 mm) O.D.;
polyurethane
14*
15
16
180243
181951
108652
1
1
SCREW, cap, hex hd;
M10 x 1.5 x 50
42{
183384
108787
2
17
189432
PISTON, pump;
17–4 PH stainless steel
O-RING; PTFE
O-RING; PTFE
PLATE, retaining
WIPER, shaft
BEARING
U-CUP; buna-N
CAP, cylinder
43
SCREW, cap, hex hd;
M5 x 0.8 x 20
2
2
4
2
2
2
2
2
2
4
1
4
1
2
2
1
2
4
2
2
2
2
2
2
1
1
6
1
1
18*
19*
20
21
22
23*
25
26*
108824
108825
181967
108713
183228
108158
183098
108874
44
46
47
48*
49
50
51
52*
53
54*
55
56
57
58
59
60
61
64
71
72{
181950
108790
220490
103341
186676
220491
108647
107098
181969
108822
181976
181845
108287
108644
104582
104029
108788
183429
179944
179861
BRACKET, mounting
WASHER, flat
INTAKE MANIFOLD
O-RING; PTFE
SEAT, valve
OUTLET MANIFOLD
CONNECTOR, straight thread
O-RING; PTFE
CAP
O-RING; PTFE
STOP, ball
GUIDE, ball
BALL; stainless steel
PLUG, boss
WASHER, tab
LUG, grounding
WASHER, flat
LABEL, warning
LABEL, warning
TUBE, 0.245 in. (6.35 mm) O.D.;
polyurethane
SEAL, hydraulic
O-RING; buna-N
60
59
72{
40
37
1
2
73
16F143
5
*
Parts included in Repair Kits 220949 (for pump
Model 220666); and 237014 (for pump Model
237011), which may be purchased separately.
43
42{
39
38
{ Parts included in Repair Kit 220656, which may be
purchased separately.
See pages 38 – 40 for description of all Repair Kits,
Optional Repair Kits, and Conversion Kits available.
02333
307843 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
1200 Series Carbon Steel Pumps
Model 220664, Series D
Model 237009, Series A
23*
14*
31
32
22
53
21
20
55
54*
36
17
19*
57
16
18*
56
12
49
13*
48*
58
19*
47
46
32
52*
33
35
34
1
52*
2
51
73
50
26*
27
30
28*
29
26*
15
25
46
4
47
71
1
2
64
44
3
02332
28 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref.
No.
1200 Series Carbon Steel Pumps
Model 220664, Series D
Part No. Description
Qty.
Model 237009, Series A
26*
27
108874
183097
107160
183355
183229
181998
108768
O-RING; buna-N
2
1
1
1
1
2
CYLINDER, air motor
QUAD RING; buna-N
PISTON, air motor
STUD
ACCUMULATOR
SCREW, cap, hex hd;
M8 x 1.25 x 16
HOUSING, pump outlet
SCREW, cap, hex hd;
M12 x 1.75 100
Ref.
No.
Part No. Description
Qty.
28*
29
30
31
32
1
2
3
108712
104572
108786
NUT, hex; M8 x 1.25
8
8
WASHER, spring lock
SCREW, cap, hex hd;
M8 x 1.25 x 130
2
6
8
2
4
5
108711
221133
SCREW, cap, hex hd;
M8 x 1.25 x 120
PILOT VALVE ASSY
See page 37 for parts
PLATE, Retaining
SEAL, piston; UHMWPE
(for pump Model 220664 only)
SEAL, piston; Nylon
(for pump Model 237009 only)
SEAL, bellows; polypropylene
SHAFT, piston
33
34
181854
108654
8
8
2
2
2
35
36
37
107541
181847
107100
WASHER, lock
12
13*
181973
183240
HOUSING, pump intake
SCREW, cap, hex sch;
M5 x 0.8 x 12
2
4
2
2
188178
38
39
40
107189
107190
220902
MUFFLER
2
2
2
RING, lock; 1/2 – 14 npt
AIR CONTROL VALVE ASSY
See page 36 for parts
TUBE, 0.25 in. (6.35 mm) O.D.;
polyurethane
SCREW, cap, hex hd;
M5 x 0.8 x 20
BRACKET, mounting
WASHER, flat
INTAKE MANIFOLD
O-RING; PTFE
SEAT, valve
OUTLET MANIFOLD
CONNECTOR, straight thread
O-RING; PTFE
CAP
O-RING; PTFE
STOP, ball; stainless steel
GUIDE, ball; stainless steel
BALL; stainless steel
PLUG, boss
WASHER, tab
LUG, grounding
LABEL, warning
LABEL, warning
TUBE, 0.245 in. (6.35 mm) O.D.;
14*
15
16
180243
181951
108652
1
1
SCREW, cap, hex hd;
M10 x 1.5 x 50
42{
183384
108787
2
17
189433
PISTON, pump;
17–4 PH stainless steel
O-RING; PTFE
O-RING; PTFE
PLATE, retaining; stainless steel
WIPER, shaft
BEARING
U-CUP; buna-N
CAP, cylinder
43
2
2
4
2
2
2
2
2
4
1
10
1
2
2
1
2
4
2
2
2
2
2
2
1
1
1
18*
19*
20
21
22
108824
108825
181967
108713
183228
108158
183098
44
46
47
48*
49
50
51
52*
53
54*
55
56
57
58
59
60
64
71
72{
181950
108788
220486
103341
181947
220485
108648
107098
181949
108822
181976
181845
107167
108643
104582
104029
183429
179944
179861
23*
25
60
59
72{
40
37
1
polyurethane
SEAL, hydraulic
1
2
73
16F143
5
*
Parts included in Repair Kits 221136 (for pump
Model 220664); and 237017 (for pump Model
237009), which may be purchased separately.
43
42{
39
38
{ Parts included in Repair Kit 220656, which may be
purchased separately.
02333
See pages 38 – 40 for description of all Repair Kits,
Optional Repair Kits, and Conversion Kits available.
307843 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
1200 Series Stainless Steel Pumps
Model 220667, Series D
Model 237012, Series A
23*
14*
22
53
31
32
21
20
55
54*
36
17
19*
57
16
18*
56
12
49
13*
48*
58
19*
47
46
32
52*
33
35
34
1
52*
2
51
73
26*
50
27
30
28*
29
26*
15
25
61
4
47
71
1
2
64
44
3
02332
30 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref.
No.
1200 Series Stainless Steel Pumps
Model 220667, Series D
Model 237012, Series A
Ref .
Part No. Description
Qty.
27
183097
107160
183355
183229
220971
108791
CYLINDER, air motor
1
1
1
1
2
28*
29
30
31
32
QUAD RING; buna-N
PISTON, air motor
STUD
ACCUMULATOR
SCREW, cap, hex hd;
M8 x 1.25 x 16
HOUSING, pump outlet
SCREW, cap, hex hd;
M12 x 1.75 100
No.
Part No. Description
Qty.
1
2
3
108712
104572
108786
NUT, hex; M8 x 1.25
8
8
WASHER, spring lock
SCREW, cap, hex hd;
M8 x 1.25 x 130
2
6
8
2
4
5
108711
221133
SCREW, cap, hex hd;
M8 x 1.25 x 120
PILOT VALVE ASSY
See page 37 for parts
PLATE, retaining
SEAL, piston; UHMWPE
(for pump Model 220667 only)
SEAL, piston; Nylon
(for pump Model 237012 only)
SEAL, bellows; polypropylene
SHAFT, piston
33
34
181866
108793
8
8
2
2
2
35
36
37
111449
181865
107100
WASHER
12
13*
181973
183240
HOUSING, pump intake
SCREW, cap, hex sch;
M5 x 0.8 x 12
2
4
2
2
188178
38
39
40
107189
107190
220902
MUFFLER
2
2
2
RING, lock; 1/2 – 14 npt
AIR CONTROL VALVE ASSY
See page 36 for parts
TUBE, 0.25 in. (6.35 mm) O.D.;
polyurethane
14*
15
16
180243
181951
108652
1
1
SCREW, cap, hex hd;
M10 x 1.5 x 50
42{
183384
108787
2
17
189433
108824
PISTON, pump;
17–4 PH stainless steel
O-RING; PTFE
43
SCREW, cap, hex hd;
M5 x 0.8 x 20
2
2
4
2
2
2
2
2
2
4
1
6
1
2
2
1
2
4
2
2
2
2
2
2
1
1
4
1
1
18*
19*
20
21
22
23*
25
26*
44
46
47
48*
49
50
51
52*
53
54*
55
56
57
58
59
60
61
64
71
72{
181950
108790
220490
103341
220948
220491
108647
107098
181969
108822
181976
181845
108287
108644
104582
104029
108788
183429
179944
179861
BRACKET, mounting
WASHER, flat
INTAKE MANIFOLD
O-RING; PTFE
SEAT, valve
OUTLET MANIFOLD
CONNECTOR, straight thread
O-RING; PTFE
CAP
O-RING; PTFE
STOP, ball
GUIDE, ball
BALL; stainless steel
PLUG, boss
WASHER, tab
LUG, grounding
WASHER, flat
LABEL, warning
LABEL, warning
108825* O-RING; PTFE
181967
108713
183228
108158
183098
108874
PLATE, retaining
WIPER, shaft
BEARING
U-CUP; buna-N
CAP, cylinder
O-RING; buna-N
60
59
72{
40
37
TUBE, 0.245 in. (6.35 mm) O.D.;
polyurethane
SEAL, hydraulic
1
2
73
16F143
5
*
Parts included in Repair Kits 221136 (for pump
Model 220667); and 237017 (for pump Model
237012), which may be purchased separately.
43
39
38
42{
{ Parts included in Repair Kit 220656, which may be
purchased separately.
02333
See pages 38 – 40 for description of all Repair Kits,
Optional Repair Kits, and Conversion Kits available.
307843 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
2500 Series Carbon Steel Pumps
Model 220665, Series D
Model 237010, Series A
23*
22
21
53
20
55
14*
54*
36
17
57
16
18*
56
12
49
13*
48*
58
19*
47
46
32
52*
33
65
35
34
1
2
52*
51
73
26*
50
27
30
28*
29
26*
15
25
61
4
47
71
1
2
64
02334
3
44
32 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
26*
27
108874
183097
107160
183355
183229
108768
O-RING; buna-N
2
1
1
1
1
2500 Series Carbon Steel Pumps
Model 220665, Series D
CYLINDER, air motor
QUAD RING; buna-N
PISTON, air motor
STUD
SCREW, cap, hex hd;
M8 x 1.25 x 16
HOUSING, pump outlet
SCREW, cap, hex hd;
M10 x 1.5 x 100
28*
29
Model 237010, Series A
Ref.
No.
30
32
Part No. Description
Qty.
1
2
3
108712
104572
108786
NUT, hex; M8 x 1.25
8
4
2
WASHER, spring lock
SCREW, cap, hex hd;
M8 x 1.25 x 130
8
33
181853
108655
34
2
8
8
2
4
5
108711
221133
SCREW, cap, hex hd;
M8 x 1.25 x 120
PILOT VALVE ASSY
See page 37 for parts
PLATE, retaining
SEAL, piston; UHMWPE
(for pump Model 220665 only)
SEAL, piston; Nylon
(for pump Model 237010 only)
SEAL, bellows; polypropylene
SHAFT, piston
35
6
108770
181856
107100
WASHER, lock
36
HOUSING, pump intake
SCREW, cap, hex sch;
M5 x 0.8 x 12
37
2
4
2
2
12
13*
181958
181959
2
38
107189
107190
220902
MUFFLER
39
40
RING, lock; 1/2 – 14 npt
AIR CONTROL VALVE ASSY
See page 36 for parts
TUBE, 0.25 in. (6.35 mm) O.D.;
polyurethane
SCREW, cap, hex hd;
M5 x 0.8 x 20
BRACKET, mounting
WASHER, flat
INTAKE MANIFOLD
O-RING; PTFE
SEAT, valve
OUTLET MANIFOLD
CONNECTOR, straight thread
O-RING; PTFE
CAP
O-RING; PTFE
STOP, ball; stainless steel
GUIDE, ball; stainless steel
BALL; stainless steel
PLUG, boss
WASHER, tab
LUG, grounding
LABEL, warning
TEE, outlet, female
2
188176
1
1
2
2
42{
183384
108787
14*
15
16
180243
181951
108652
2
43
SCREW, cap, hex hd;
M10 x 1.5 x 50
4
1
10
1
2
2
2
2
4
2
2
2
2
2
2
1
1
1
1
1
2
44
181950
108788
220486
107313
189067
220487
108646
108526
181949
108822
185552
181852
101822
108642
104582
104029
183429
108869
179944
179861
17
189434
PISTON, pump;
46
17–4 PH stainless steel
O-RING; PTFE
O-RING; PTFE
2
47
2
18*
19*
20
21
22
108823
108825
181967
108713
183228
108158
183098
48*
2
49
2
PLATE, retaining; stainless steel
50
2
WIPER, shaft
BEARING
U-CUP; buna-N
CAP, cylinder
51
2
52*
2
23*
25
53
2
54*
55
56
57
58
59
60
64
65
71
72{
60
59
72{
40
37
LABEL, warning
TUBE, 0.245 in. (6.35 mm) O.D.;
polyurethane
1
4
73
16F142
SEAL, hydraulic
*
Parts included in Repair Kits 220950 (for pump
Model 220665); and 237016 (for pump Model
237010), which may be purchased separately.
5
43
{ Parts included in Repair Kit 220656, which may be
purchased separately.
39
38
42{
See pages 38 – 40 for description of all Repair Kits,
Optional Repair Kits, and Conversion Kits available.
02333
Ref.
No.
Part No. Description
Qty.
307843 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
2500 Series Stainless Steel Pumps
Model 220668, Series D
Model 237013, Series A
23*
22
21
53
20
14*
55
36
54*
17
57
16
56
18*
12
49
13*
48*
58
19*
47
46
65
32
52*
33
35
34
66
1
52*
2
51
73
50
26*
27
30
28*
29
26*
15
25
46
4
47
71
1
2
64
3
44
02335
34 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
2500 Series Stainless Steel Pumps
Model 220668, Series D
Model 237013, Series A
Ref.
No.
1
2
3
Ref.
No.
27
Part No. Description
Qty.
8
Part No. Description
Qty.
1
108712
104572
108786
NUT, hex; M8 x 1.25
183097
107160
183355
183229
108791
CYLINDER, air motor
28*
29
QUAD RING; buna-N
PISTON, air motor
STUD
SCREW, cap, hex hd;
M8 x 1.25 x 16
1
1
1
WASHER, spring lock
SCREW, cap, hex hd;
M8 x 1.25 x 130
8
30
32
2
6
4
5
108711
221133
SCREW, cap, hex hd;
M8 x 1.25 x 120
PILOT VALVE ASSY
See page 37 for parts
PLATE, retaining
SEAL, piston; UHMWPE
(for pump Model 220668 only)
SEAL, piston; Nylon
(for pump Model 237013 only)
SEAL, bellows; polypropylene
SHAFT, piston
4
2
33
34
185554
110622
HOUSING, pump outlet
SCREW, cap, hex hd;
M10 x 1.5 x 100
2
2
8
8
2
12
13*
185940
181959
35
36
37
100731
185555
107100
WASHER
HOUSING, pump intake
SCREW, cap, hex sch;
M5 x 0.8 x 12
2
188176
4
2
2
2
2
2
38
39
40
107189
107190
220902
MUFFLER
14*
15
16
180243
181951
108652
RING, lock; 1/2 – 14 npt
AIR CONTROL VALVE ASSY
See page 36 for parts
WASHER, Flat
TUBE, 0.25 in. (6.35 mm) O.D.;
polyurethane
SCREW, cap, hex hd;
M10 x 1.5 x 50
1
4
2
41
108790
183384
17
189434
PISTON, pump;
42{
17–4 PH stainless steel
O-RING; PTFE
O-RING; PTFE
2
2
2
1
18*
19*
20
21
22
23*
25
26*
108823
108825
181967
108713
183228
108158
183098
108874
43
108787
SCREW, cap, hex hd;
M5 x 0.8 x 20
BRACKET, mounting
WASHER, flat
INTAKE MANIFOLD
O-RING; PTFE
SEAT, valve
OUTLET MANIFOLD
CONNECTOR, straight thread
O-RING; PTFE
CAP
O-RING; PTFE
STOP, ball
GUIDE, ball; stainless steel
BALL; stainless steel
PLUG, boss
WASHER, Tab
LUG, grounding
4
1
6
1
2
2
2
2
4
2
2
2
2
2
2
1
1
1
PLATE, retaining; stainless steel
WIPER, shaft
2
2
2
2
2
2
44
46
47
48*
49
50
51
52*
53
54*
55
56
57
58
59
60
64
65
66
181950
108788
220490
107313
189067
223111
185553
108526
181969
108822
185552
181852
101822
185941
104582
104029
183429
110315
112176
BEARING
U-CUP; buna-N
CAP, cylinder
O-RING; buna-N
60
59
72{
40
37
LABEL, warning
TEE, outlet, male; stainless steel
COUPLING, female, 3/4 npt;
stainless steel
1
71
72{
179944
179861
LABEL, warning
TUBE, 0.245 in. (6.35 mm) O.D.;
1
polyurethane
SEAL, hydraulic
1
4
5
73
16F142
*
Parts included in Repair Kits 220950 (for pump
Model 220668); and 237016 (for pump Model
237013), which may be purchased separately.
43
39
38
42{
{ Parts included in Repair Kit 220656, which may be
purchased separately.
02333
See pages 38 – 40 for description of all Repair Kits,
Optional Repair Kits, and Conversion Kits available.
307843 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref No. 40
Air Control Valve 220902
40r
40s
NOTE: This assembly is included
with all pump models.
40p
40q
40m
40h*
40a
*40j
40e
40d
40k
*40i
40c
*40h
*40f
*40g
40b
02330
40n
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
40k
108780
SCREW, cap, hex hd;
M5 x 0.8 x 150
NUT, full hex; 10–24 UNC–2A
TEE, barbed
TUBE, polyurethane; 0.25 in.
(6.35 mm) O.D.
FILTER, air
HOUSING, air filter
FITTING, barbed,
with buna-N o-ring
40a
40b
40c
40d
40e
40f * 181464
40g* 105400
40h* 107186
183370
183369
183368
183367
183366
HOUSING, valve center
HOUSING, valve end
SPOOL, differential
STEM, spool
RETAINER, seal
GASKET, polyurethane
O-RING, buna-N
O-RING, buna-N
U-CUP, polyurethane
U-CUP, polyurethane
1
2
2
1
2
2
2
4
2
2
4
4
2
40m 100179
40n 107191
40p* 179861
2
1
1
40q
40r
40s
160736
183620
108383
40i*
40j*
108781
108782
2
*
These parts are included in Repair Kit 220656. See
pages 38 – 40 for description of all Repair Kits, Op-
tional Repair Kits, and Conversion Kits available.
36 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref No. 5
Pilot Valve 221133
NOTE: This assembly is included
with all pump models.
5j*
5d
5e
5a
5g
5b
5h
5f
5i*
5c
02331
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
5h
108383
FITTING, barbed, buna-N o-ring
seal; 10–32 UNF–2A
GASKET, copper
SEAL, pilot valve rod, buna-N
5a
5b
5c
5d
5e*
5f
183604
183603
183605
183606
159589
108961
108960
STEM, valve
VALVE, air
CAP, valve
HOUSING, valve
O-RING, buna-N
1
1
1
2
1
1
1
1
2
2
5i*
5j*
156766
107161
*
These parts are included in Repair Kit 220656. See
pages 38 – 40 for description of all Repair Kits, Op-
tional Repair Kits, and Conversion Kits available.
SPRING, compression
SPRING, compression
5g
307843 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair and Conversion Kits
The reference numbers shown in the kits below correspond to the reference numbers used in the parts lists and
drawings on pages 24 to 37. Use all the kit parts, even if the old parts still look good.
Standard Air Valve and Pilot Valve Repair Kit
220656
400 Series Optional Pump Repair Kit 24C134, with
UHMWPE Bellows (for pump Models 220663 and
220666)
Ref.
No.
5j
Part No. Description
Qty.
2
Ref.
107161
156766
159589
181464
110782
107186
108781
108782
179861
183384
113500
SEAL, pilot valve rod, buna-N
No.
13
14
18
19
23
26
28
48
52
54
Part No. Description
Qty.
2
5i
GASKET, copper
2
2
2
2
4
2
2
181978
15U077
108824
108825
108158
108874
107160
103341
107098
108822
SEAL, piston; UHMWPE
5e
O-RING, buna-N
SEAL, bellows, UHMWPE
O-RING, PTFE
2
2
4
2
2
1
2
4
40f
40g
40h
40i
40j
40p
42
GASKET, polyurethane
O-RING, buna-N
O-RING, buna-N
U-CUP, polyurethane
U-CUP, polyurethane
O-RING, PTFE
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
TUBE, polyurethane, 0.25 in. OD 3
TUBE, polyurethane, 0.217 in. ID 1
O-RING, PTFE
O-RING, PTFE
ADHESIVE, anaerobic
1
2
Optional Air Valve/Pilot Valve Conversion Kit
253345, with Air–Assisted Pilot Valves
400 Series Standard Pump Repair Kit 237014
(for pump Models 237008 and 237011)
Ref.
No.
5
40
40h
42
Ref.
Part No. Description
Qty.
2
No.
13
14
18
19
23
26
28
48
52
54
Part No. Description
Qty.
2
280514
253285
107186
183384
406627
VALVE, pilot
VALVE, air
O-RING, buna-N
TUBE, polyurethane, 0.217 in. ID 4
SHEET, instructions
188177
180243
108824
108825
108158
108874
107160
103341
107098
108822
SEAL, piston; Nylon
SEAL, bellows, polypropylene
O-RING, PTFE
O-RING, PTFE
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
1
4
2
2
4
2
2
1
2
4
1
400 Series Pump Urethane Piston Seal
Conversion Kit 220658
Ref.
No.
13
18
19
48
52
54
Part No. Description
Qty.
2
2
181954
108824
108825
103341
107098
108822
SEAL, piston, urethane
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2
4
2
4
400 Series Optional Pump Repair Kit 24C135, with
UHMWPE Bellows (for pump Models 237008 and
237011)
Ref.
2
No.
13
14
18
19
23
26
28
48
52
54
Part No. Description
Qty.
2
188177
15U077
108824
108825
108158
108874
107160
103341
107098
108822
SEAL, piston; Nylon
SEAL, bellows, UHMWPE
O-RING, PTFE
O-RING, PTFE
400 Series Standard Pump Repair Kit 220949
(for pump Models 220663 and 220666)
Ref.
2
2
4
2
2
1
2
4
No.
13
14
18
19
23
26
28
48
52
54
Part No. Description
Qty.
2
U-CUP, buna-N
181978
180243
108824
108825
108158
108874
107160
103341
107098
108822
SEAL, piston; UHMWPE
SEAL, bellows, polypropylene
O-RING, PTFE
O-RING, PTFE
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2
2
4
2
2
1
2
4
2
2
38 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair and Conversion Kits
The reference numbers shown in the kits below correspond to the reference numbers used in the parts lists and
drawings on pages 24 to 37. Use all the kit parts, even if the old parts still look good.
400 and 1200 Series Pumps Carbide Ball and Seat
Conversion Kit 221134
1200 Series Standard Pump Repair Kit 237017
(for pump Models 237009 and 237012)
Ref.
Ref.
No.
13
14
18
19
23
26
28
48
52
54
Part No. Description
Qty.
2
No.
Part No. Description
Qty.
188178
180243
108824
108825
108158
108874
107160
103341
107098
108822
SEAL, piston; Nylon
SEAL, bellows, polypropylene
O-RING, PTFE
O-RING, PTFE
48
49
54
57
103341
220948
108822
108286
O-RING, PTFE
SEAT, carbide
O-RING, PTFE
BALL, bearing, carbide
2
2
2
2
2
2
4
2
2
1
2
4
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
1200 Series Standard Pump Repair Kit 221136
(for pump Models 220664 and 220667)
Ref.
No.
Part No. Description
Qty.
2
13
14
18
19
23
26
28
48
52
54
183240
180243
108824
108825
108158
108874
107160
103341
107098
108822
SEAL, piston; UHMWPE
SEAL, bellows, polypropylene
O-RING, PTFE
O-RING, PTFE
2
2
2
4
2
2
1
2
4
2
1200 Series Optional Pump Repair Kit 24C131, with
UHMWPE Bellows (for pump Models 237009 and
237012)
U-CUP, buna-N
Ref.
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
No.
13
14
18
19
23
26
28
48
52
54
Part No. Description
Qty.
2
188178
15U077
108824
108825
108158
108874
107160
103341
107098
108822
SEAL, piston; Nylon
SEAL, bellows, UHMWPE
O-RING, PTFE
O-RING, PTFE
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2
2
4
2
2
1
2
4
1200 Series Optional Pump Repair Kit 24C130, with
UHMWPE Bellows, (for pump Models 220664 and
220667)
Ref.
No.
Part No. Description
Qty.
2
13
14
18
19
23
26
28
48
52
54
183240
15U077
108824
108825
108158
108874
107160
103341
107098
108822
SEAL, piston; UHMWPE
SEAL, bellows, UHMWPE
O-RING, PTFE
O-RING, PTFE
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2
2
2
4
2
2
1
2
4
2
2500 Series Pump Urethane Piston Seal
Conversion Kit 220660
Ref.
No.
13
18
19
48
52
54
Part No. Description
Qty.
2
181964
108823
108825
107313
108526
108822
SEAL, piston, urethane
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2
2
2
4
2
2500 Series Pump Carbide Ball and Seat
Conversion Kit 221135
Ref.
No.
48
49
54
57
Part No. Description
Qty.
2
107313
220947
108822
108818
O-RING, PTFE
SEAT, carbide
O-RING, PTFE
BALL, bearing, carbide
2
2
2
307843 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair and Conversion Kits
The reference numbers shown in the kits below correspond to the reference numbers used in the parts lists and
drawings on pages 24 to 37. Use all the kit parts, even if the old parts still look good.
2500 Series Standard Pump Repair Kit 220950
(for pump Models 220665 and 220668)
2500 Series Standard Pump Repair Kit 237016
(for pump Models 237010 and 237013)
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
13
14
18
19
23
26
28
48
52
54
188176
180243
108823
108825
108158
108874
107160
107313
108526
108822
SEAL, piston; Nylon
SEAL, bellows, polypropylene
O-RING, PTFE
O-RING, PTFE
2
2
2
2
2
2
1
2
4
2
13
14
18
19
23
26
28
48
52
54
181959
180243
108823
108825
108158
108874
107160
107313
108526
108822
SEAL, piston; UHMWPE
SEAL, bellows, polypropylene
O-RING, PTFE
O-RING, PTFE
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2
2
2
2
2
2
1
2
4
2
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2500 Series Optional Pump Repair Kit 24C133, with
UHMWPE Bellows (for pump Models 237010 and
237013)
2500 Series Optional Pump Repair Kit 24C132, with
UHMWPE Bellows, (for pump Models 220665 and
220668)
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
13
14
18
19
23
26
28
48
52
54
188176
15U077
108823
108825
108158
108874
107160
107313
108526
108822
SEAL, piston; Nylon
SEAL, bellows, UHMWPE
O-RING, PTFE
O-RING, PTFE
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2
2
2
2
2
2
1
2
4
2
13
14
18
19
23
26
28
48
52
54
181959
15U077
108823
108825
108158
108874
107160
107313
108526
108822
SEAL, piston; UHMWPE
SEAL, bellows, UHMWPE
O-RING, PTFE
O-RING, PTFE
U-CUP, buna-N
O-RING, buna-N
QUAD RING, buna-N
O-RING, PTFE
O-RING, PTFE
O-RING, PTFE
2
2
2
2
2
2
1
2
4
2
40 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Filter, Regulator, Lubricator Kit
Filter, Regulator, Lubricator (FRL) Kit 222345
FRL Kit 222345 (shown below) is available for Glutton pumps.
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
223004
Filter, Regulator Lubricator Assy
8
9
101689
183746
183747
100119
107142
218093
155470
222297
GAUGE, Air Pressure
Bracket
Bracket
ELBOW, street
1
1
1
1
1
1
1
1
Includes items 1 to 7
. Air Line Filter
. Air Regulator
. Lubricator
1
1
1
1
2
1
2
3
4
5
106149
104266
214848
10
11
12
13
14
15
VALVE, ball
. Nipple
HOSE, coupled
UNION, swivel, 90_
UNION, swivel, 45_
106145
. Bracket (not shown as not
used with this pump)
. U-Bolt
2
2
4
6
7
. Nut
9
7
10
8
4
3
2
11
12
13
6
1
13
REF
15 or 14
02335
307843 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Drum Cover Kit and Return Tube Kit
Drum Cover Kit 222655
Return Tube Kit 223319
Drum Cover Kit 222655 (shown below with a Glutton
pump) is available.
Return Tube Kit 223319 (shown below) is available.
Ref.
No.
Part No. Description
Qty.
Ref.
No.
Part No. Description
Qty.
1
2
185392
237949
TUBE, suction, SST
DRUM COVER ASSY
1
See manual 308466 for parts..
AGITATOR, air driven, SST
Refer to Manual 306840 for parts 1
1
101
102
103
104
108761
185394
178941
185393
ELBOW
1
1
1
1
3
4
222698
207438
ADAPTER, return
NUT, hex retaining
TUBE, return
UNION, swivel, 90_
1
Return Tube
Kit 223319
4
101
3
102
103
104
plug
NOTE: When installing the
Return Tube Kit, remove plug
and install the adapter (102)
and elbow (101). Install tube
(104) and nut (103) from the
bottom.
2
1
02337A
42 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Suction Kit
Suction Kit 208259
55 gallon drum size Suction Kit 208259 (shown below)
is available.
3
4
5
6
7
8
9
1
2
10
Ref.
No.
Part No. Description
Qty.
1
2
156589
214961
UNION, 90_ adapter,
3/4 nptf x 3/4 npsm
HOSE, cpld, nylon, 3/4 in. ID,
6 ft (1.8 m) long, w/spring guard
ELBOW, 90_
O-RING, nitrile rubber
THUMBSCREW
ADAPTER, bung
1
1
1
1
1
1
1
1
1
1
3
4
5
6
7
8
9
10
156591
156593
100220
176684
156592
159100
161377
159101
TUBE, riser
RETAINER, screen
SCREEN, filter
NUT, screen retainer
307843 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data, 400 Series Pumps
Maximum working pressure . . . . . . . . . . . . . . . . 400 psi
Wetted Parts:
(2.8 MPa, 28 bar)
Maximum air input pressure . . . . . . . . . . . . . . . . 100 psi
(0.7 MPa, 7 bar)
Air operating range . . . . . . . . . . . . . . . . . . 25 to 100 psi
(0.07 to 0.7 MPa, 1.73 to 7 bar)
Maximum continuous pump speed . . . . . . . . . . 60 cpm
Fluid flow at 60 cpm . . . . . . . . . . . . 5.6 gpm (21.2 lpm)
Fluid volume per cycle . . . . . . . . 0.096 gal (0.366 liter)
Maximum suction lift (water) . . . . . . . . . . 15 ft (4.57 m)
Maximum operating temperature . . . . . 150_ F (65_ C)
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 npt(f)
Fluid inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25 npt(f)
Fluid outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 npt(f)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 80.5 lb (36.2 kg)
Model 220663 and 237008:
carbon steel, stainless steel, polypropylene, ultra
high molecular weight polyethylene{, Nylon},
PTFE
{ Model 220663 only
} Model 237008 only
Model 220666 and 237011:
304 and 316 stainless steel, 17–4 PH stainless
steel, polypropylene, ultra high molecular weight
polyethylene{, Nylon}, PTFE
{ Model 220666 only
} Model 237011 only
Performance Chart, 400 Series Pumps
AIR FLOW
SCFM m3/min
0
20
40
60 CPM
60
1.68
A
B
50
1.40
psi MPa bar
2.8
28
40
30
1.12
0.84
400
300
200
100
A
B
2.1
1.4
21
14
C
20
0.56
C
0.7
0
7
10
0
0.28
0
0
0
1
2
3
4
5
6
22.5
7
8
GPM
0
3.75
7.5
11.25
15
18.75
26.25
30
lpm
KEY: Fluid Outlet Pressure: black curves
FLUID FLOW
Air Consumption: gray curves
A
B
C
at 100 psi (0.7 MPa, 7 bar) air pressure
at 70 psi (0.48 MPa, 4.9 bar) air pressure
at 40 psi (0.28 MPa, 2.8 bar) air pressure
To find pump air consumption (CFM, m3/min) specific de-
livery (GPM, lpm) and operating air pressure (psi/MPa/bar):
To find outlet pressure (psi/MPa/bar) at a specific delivery
(GPM, lpm) and operating air pressure (psi/MPa/bar):
1. Locate desired delivery along bottom of chart.
1. Locate desired delivery along bottom of chart.
2. Read vertical line up to intersection with selected air con-
sumption curve. Follow right to scale and read air con-
sumption.
2. Read vertical line up to intersection with selected fluid
outlet pressure curve. Follow left to scale and read outlet
pressure.
44 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data, 1200 Series Pumps
Maximum working pressure . . . . . . . . . . . . . . 1200 psi
(8.3 MPa, 83 bar)
Maximum air input pressure . . . . . . . . . . . . . . . . 100 psi
(0.7 MPa, 7 bar)
Air operating range . . . . . . . . . . . . . . . . . . 25 to 100 psi
(0.07 to 0.7 MPa, 1.73 to 7 bar)
Maximum continuous pump speed . . . . . . . . . . 60 cpm
Fluid flow at 60 cpm . . . . . . . . . . . . . . . 2 gpm (7.5 lpm)
Fluid volume per cycle . . . . . . . . 0.034 gal (0.128 liter)
Maximum suction lift (water) . . . . . . . . . . 15 ft (4.57 m)
Maximum operating temperature . . . . . 150_ F (65_ C)
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 npt(f)
Fluid inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25 npt(f)
Fluid outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 npt(f)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 lb (35.1 kg)
Wetted Parts:
Model 220664 and 237009:
carbon steel, stainless steel, polypropylene, ultra
high molecular weight polyethylene{, Nylon},
PTFE
{ Model 220664 only
} Model 237009 only
Model 220667 and 237012:
304 and 316 stainless steel, 17–4 PH stainless
steel, polypropylene, ultra high molecular weight
polyethylene{, Nylon}, PTFE
{ Model 220667 only
} Model 237012 only
Performance Chart, 1200 Series Pumps
AIR FLOW
psi MPa bar
SCFM m3/min
0
20
40
60 CPM
60
1.68
83
1200 8.3
A
50
1.40
7
69
1000
800
A
40
30
1.12
0.84
5.5
4.2
2.8
1.4
55
41
28
B
B
600
400
C
20
0.56
C
10
0
0.28
0
14
200
0
0.0
0
0.5
1.9
1.0
3.8
1.5
5.7
2.0
7.5
2.5
9.5
GPM
lpm
KEY: Fluid Outlet Pressure: black curves
FLUID FLOW
Air Consumption: gray curves
A
B
C
at 100 psi (0.7 MPa, 7 bar) air pressure
at 70 psi (0.48 MPa, 4.9 bar) air pressure
at 40 psi (0.28 MPa, 2.8 bar) air pressure
To find pump air consumption (CFM, m3/min) specific de-
livery (GPM, lpm) and operating air pressure (psi/MPa/bar):
To find outlet pressure (psi/MPa/bar) at a specific delivery
(GPM, lpm) and operating air pressure (psi/MPa/bar):
1. Locate desired delivery along bottom of chart.
1. Locate desired delivery along bottom of chart.
2. Read vertical line up to intersection with selected air con-
sumption curve. Follow right to scale and read air con-
sumption.
2. Read vertical line up to intersection with selected fluid
outlet pressure curve. Follow left to scale and read outlet
pressure.
307843 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data, 2500 Series Pumps
Maximum working pressure . . . . . . . . . . . . . . 2500 psi
(17 MPa, 170 bar)
Maximum air input pressure . . . . . . . . . . . . . . . . 100 psi
(0.7 MPa, 7 bar)
Air operating range . . . . . . . . . . . . . . . . . . 25 to 100 psi
(0.07 to 0.7 MPa, 1.73 to 7 bar)
Maximum continuous pump speed . . . . . . . . . . 60 cpm
Fluid flow at 60 cpm . . . . . . . . . . . . . 0.9 gpm (3.4 lpm)
Fluid volume per cycle . . . . . . . . 0.015 gal (0.058 liter)
Maximum suction lift (water) . . . . . . . . . . . 6 ft (1.83 m)
Maximum operating temperature . . . . . 150_ F (65_ C)
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 npt(f)
Fluid inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25 npt(f)
Fluid outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4 npt(f)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 lb (27.5 kg)
Wetted Parts:
Model 220665 and 237010:
carbon steel, stainless steel, polypropylene, ultra
high molecular weight polyethylene{, Nylon},
PTFE
{ Model 220665 only
} Model 237010 only
Model 220668 and 237013:
304 and 316 stainless steel, 17–4 PH stainless
steel, polypropylene, ultra high molecular weight
polyethylene{, Nylon}, PTFE
{ Model 220668 only
} Model 237013 only
Performance Chart, 2500 Series Pumps
AIR FLOW
SCFM m3/min
0
20
40
60 CPM
psi
MPa bar
A
2400
168
147
6.72
16.8
14.7
60.0
52.5
45.0
37.5
30.0
22.5
15.0
7.5
A
2100
1800
1500
5.88
5.04
4.20
3.36
2.52
1.68
B
12.6 126
B
10
102
84
8.4
6.2
4.2
2.1
1200
900
600
200
C
62
41
21
C
0.84
0
0
0
0.00
0
0.25
0.95
0.50
1.89
0.75
2.84
1.00
3.79
1.25
4.73
1.50
5.68
GPM
lpm
KEY: Fluid Outlet Pressure: black curves
FLUID FLOW
Air Consumption: gray curves
A
B
C
at 100 psi (0.7 MPa, 7 bar) air pressure
at 70 psi (0.48 MPa, 4.9 bar) air pressure
at 40 psi (0.28 MPa, 2.8 bar) air pressure
To find pump air consumption (CFM, m3/min) specific de-
livery (GPM, lpm) and operating air pressure (psi/MPa/bar):
To find outlet pressure (psi/MPa/bar) at a specific delivery
(GPM, lpm) and operating air pressure (psi/MPa/bar):
1. Locate desired delivery along bottom of chart.
1. Locate desired delivery along bottom of chart.
2. Read vertical line up to intersection with selected air con-
sumption curve. Follow right to scale and read air con-
sumption.
2. Read vertical line up to intersection with selected fluid
outlet pressure curve. Follow left to scale and read outlet
pressure.
46 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensional Drawing
4
6
1
02321
3
5
2
Height
400 and 1200 Series pumps: 15.1 in. (384 mm)
2500 Series pumps: 12.6 in. (320 mm)
19.6 in. (498 mm)
1
2
Width:
Depth:
15.83 in. (401 mm)
1/2 npt(f)
3
4
5
Air inlet
Fluid inlet:
1.25 npt(f)
6
Fluid outlet
400 and 1200 Series pumps: 1 npt(f)
2500 Series pumps: 3/4 npt(f)
Mounting Hole Layout
1
1
2
Four-hole bolt pattern on 10.5-in. (267mm) dia. circle
Three-hole bolt pattern on 6.38-in. (162mm) dia. circle
2
02324
307843 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 307843
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES S P.O. BOX 1441 S MINNEAPOLIS, MN 55440-1441 S USA
Copyright 1988, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revised October 2013
48 307843
Download from Www.Somanuals.com. All Manuals Search And Download.
|