Fujitsu Server TX200FT S2 User Manual

B7FH-3821-01EN-00

TX200FT S2

��

■PRIMERGY TX200FT S2 Manuals

Manuals for this server can be accessed from the section below of the PRIMERGY Document & Tool CD.

[CD-ROM Drive] :\MANUAL\INDEX.PDF

Manuals can be displayed using Acrobat Reader or Adobe Reader . If using Acrobat Reader , use version 4.0 or later.

Checking the items

supplied

Checking "Safety Pre-

cautions"

Using the "Contents List", check that no supplied

or attached items are missing. If any items are

missing, contact an ofﬁce listed in the "Contact

Information.

Before using this server, be sure to check the at-

tached "Safety Precautions" guidelines.

Also check the guidelines when connecting, installing

internal options and setting up this server.

Installing internal options

If internal options have been purchased separately, install them before installing the Operating System.

Points to note when installing

internal options

Available internal options and

installation locations

��

When installing internal options, perform operations after

reading the following manuals.

��

"Chapter 5 Installing Internal Options"

��

"PRIMERGY ServerBooks"/

"Supplement"

When installing memory or hard disk, always install the

same capacity of memory or hard disk to both enclo-

sures.

��

After installing internal options, check that the order and

location of installation are correct and cables are cor-

rectly attached.

Download from Www.Somanuals.com. All Manuals Search And Download.

Attach M5 rack nuts.

Use 4U for each enclosure.

Insert the rack nuts in the 2nd and 11th hole posi-

tions, counting up from the base of the server, from

inside of the rack bracket.

Insert the server to install it to the rack.

Insert the inner rail attached to the server to the

grooves of the slide rail and slide the server to-

wards the back.

Hold the locks on the right and left of the slide rail

pressed and slide the server even further into the

rack.

��

Lock

��

Attach the rail to the rack.

Fasten the slide rail to the 1st and 3rd hole positions,

counting up from the base of the server, with M5

ﬂathead screws and washers.

��

Be careful when sliding the server into the rack and

returning to the original position.

��

There is a fear you may pinch your ﬁngers or catch

your clothing.

��

Fasten the server to the rack.

Fasten using 4 thumbscrews (M5).

��

Install the second enclosure to the rack

in the same way.

Pull the slide rails toward the front until

they click into place.

If a server or peripheral devices are not installed in the

rack, install the attached blank panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting peripheral devices

Peripheral devices, such as the keyboard and mouse, etc., are connected to the server in the following

order.

Connecting the LAN cables

Connecting the display, keyboard and mouse

��

Connecting power cables (when using UPS)

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Filling in the pair identiﬁcation label

Fill in the label on the front of the server so that it is clear that FT1 and FT2 are a pair.

Also, inform the support desk of the product ID and number of the FT1/FT2 when you contact them. Be sure to ﬁll in this

information.

��

Deciding required information before running mini-setup

of the OS

Before running mini-setup of the OS decide the following information.

- User information (User and password)

- Owner information

- Validation interval at automatic shutdown (for UPS use only)

- Network Conﬁguration

Decide and enter the values in the sheet below. Be sure to keep this sheet after entering.

User information

Item

FT1 (CoServer1)

FT2 (CoServer2)

User name

Password *¹

User name

Password *^{1, 2}

User name

Password

Administrator

FTvirtual Server system administrator

CoServer system administrator

UPS service system administrator *3

PowerChute BusinessEdition user *4

GAM (RAID administration) user

User name

Password

User name

Password *^{1, 2}

gamroot

*1 : Do not leave the password blank.

*2 : A separate password can be set for CoServer1 and CoServer2 but in order to avoid complicating various setting pro-

cedures it is recommended that the same password be set for both.

*3 : This user is not related in anyway to the Windows user account because it is set on PowerChute BusinessEdition.

*4 : UPS service logon account.

Owner information

Item

FTvirtual Server

FT1 (CoServer1)

FT2 (CoServer2)

Name

Organization

Download from Www.Somanuals.com. All Manuals Search And Download.

Validation interval at automatic shutdown

This setting required for the use of UPS.

For details about various settings, refer to "3.4 UPS Settings" in the "User's Guide". The numbers in brackets ( ) are setting

examples.

Item

Actual Setting Parameters

Time

"Power Failure" - "When power fails, begin a shutdown

procedure:" - "After UPS has been on battery for" in

Device Properties.

minutes

(1 min)

Validation interval from the power failure

to the start of FTvirtual Server shutdown

Validation interval from the start of FTvirtual Select Device properties "Shutdown Sequence" -

minutes

(3 mins)

Server shutdown to the start of CoServer

shutdown (Command ﬁle execution time)

"Conﬁgure Shutdown Sequence" - "Next" - "OS" and

then "Delay".

Validation interval from the start of CoServer Select Device properties "Shutdown Sequence" -

shutdown to UPS power off (time required for "Conﬁgure Shutdown Sequence" - "Next" - "OS" and

minutes

(1 minute

30 seconds)

OS shutdown)

then "Duration".

minutes

seconds

(5 minutes

30 seconds)

Total

Network conﬁguration

CoServer Link1, CoServer Link2, Virtual Network1 and Virtual Network2 are internal network settings. Normally modiﬁ-

cations are not required.

However, when there is a conﬂict with an external network, refer to "3.2 Network Functions" in the "User’s Guide" before

setting. Figures in the brackets ( ) are default values.

FTvirtual Server

Item

IP address

Subnet mask

Computer name

Local area connection (FTvirtual Server LAN)

Virtual Network1

(255 . 255 . 255 . 252)

(192 . 168 . 181 . 81)

(192 . 168 . 181 . 85)

Virtual Network2

CoServer1 (FT1)

CoServer2 (FT2)

Item

IP address

Subnet mask

IP address

Subnet mask

Computer name

CoServer Management

(CoServer LAN)

CoServer Link1

CoServer Link2

Virtual Network

(

192 .168 .181 . 89

192 .168 .181 . 93

192 .168 .181 . 82

)

(

255 .255 .255 .252

)

(

192 .168 .181 . 90

192 .168 .181 . 94)

192 .168 .181 . 86)

)

(

255 .255 .255 .252

)

(

255 .255 .255 .252

(

255 .255 .255 .252)

(

When setting, the FTvirtual Server LAN adapter appears (Redirected 0) on the CoServer, but it is reserved because it is

used by the FTvirtual Server.

Do not bind internet protocol (TCP/IP) and do not set IP addresses or subnet masks to these adapters on the CoServer.

Set the FTvirtual Server LAN IP address and the subnet mask on the FTvirtual Server.

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning on the power and run mini-setup of each OS

This section explains how to run mini-setup of CoServer1, CoServer2 and FTvirtual Server.

To run mini-setup of FTvirtual Server, CoServer1 and 2 must already be run mini-setup.

Run mini-setup in the following order.

(1) Turn on the FT1 power and run mini-setup of CoServer1. Do not yet turn on the power of FT2.

(2) Turn on the FT2 power and run mini-setup of CoServer2. The procedure is the same as for CoServer1.

(3) Logon to CoServer1 and 2 and run mini-setup of FTvirtual Server.

- CoServer1 and CoServer2 cannot be run mini-setup at the same time. After turning on the power of FT1 do not turn on

the power of FT2 until CoServer1 has ﬁnished running mini-setup.

- When an internal hard disk has been added or changing the size of C drive on the FTvirtual Server, before running mini-

setup of each OS, perform recovery using the recovery CD.

"7.7 Restoring Settings at the Time of Purchase (Recovery)"

��

Running mini-setup of the CoServer1

- Adding/deleting devices become easier if the

password for CoServer1 and CoServer2 are

the same.

- You must set a password. If not, an FT-system

internal communication problem will occur.

- Sometimes you cannot return even by press-

ing [Back]. Check the parameters carefully and

click [Next].

Check that the FTvirtual Server LAN

and CoServer LAN are not connected

to the server and turn on the power

supply of the peripheral devices.

When connecting UPS check that UPS has a nor-

mal power supply.

Press the power switch on the FT1.

After completing setup, the server restarts and start

Windows OS.

��

Logon to CoServer1.

When the following screen appears enter "Endur-

ance License Number" and click [OK].

��

When the power is turned on, the server is checked

using "Power On Self Test (POST)".

If any abnormalities are detected by POST, error

messages are displayed.

"7.3 Error Messages"

��

- The Endurance License Number is printed in

About Endurance License Number for Version

After POST is ﬁnished, running mini-setup opera-

tions automatically start.

6.x supplied with the recovery CD.

This number can be used for both CoServer1

and CoServer2.

- Depending on the environment sometimes a

NumLock status occurs. In this case, press the

NumLock key to unlock the lock and then enter

Endurance License Number.

When running mini-setup, enter the

following parameters.

Check the parameter setting values and click

"Next".

- After logging on to CoServer, a DOS prompt

window appears at the same time as the "En-

durance License Number" dialogue box ap-

pears. However, do not perform operations

such as closing DOS prompt windows.

- Personalize Your Software

(Name, organization)

- Computer name & Administrator password

- Date and Time Settings

A message that recommends restarting appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click [Yes].

CoServer restarts.

When the server restarts, press the

power switch on the front of the server

straight away and turn off the power

supply.

After restarting, the POST screen (or

"PRIMERGY" logo) appears.

Running mini-setup of the CoServer2

The running mini-setup procedure is the same as for CoServer1. Press the power switch on the front of

FT2 and turn on the power supply. For details about further operations, refer to " Running mini-setup

of the CoServer1" and run mini-setup.

Running mini-setup of the FTvirtual server

Click [Start] " [All Programs] " [Mara-

thon Endurance] " [Management Tasks]

" [FTvirtual Server] " [Start] in CoServ-

er1 in this order.

The start window of Windows setup wizard ap-

pears.

Turn on the power supply of FT1 and

FT2.

��

Nothing is displayed on the Endurance FTvirtual

Server Desktop momentarily, but this does not indi-

cate an error. Please wait for a short while.

Click [Next].

Start setup. During setup enter the following pa-

rameters. All other parameters are optional. After

checking the parameter setting values, click [Next].

After POST has ﬁnished, the OS selection window

appears.

- License Agreement

- Personalize Your Software

(Name, organization)

- Computer name & Administrator password

- Date and Time Settings

��

When setup is complete, the FTvirtual Server re-

starts and the logon window appears.

Check that "Online Endurance CoServ-

er" has been selected and press the

[Enter] key.

Logon to FTvirtual Server.

Start Endurance Manager.

The logon window appears.

If the above operations are not performed, after a

temporary stop (30 secs) it begins to operate as the

"Online Endurance CoServer". It is ﬁne to move on

to the next operation.

Click [Start] [All Programs] [Marathon En-

durance] [Manager] to start Endurance Manager.

Enter the administrators privileges

password in FT1 and logon to CoServ-

er1.

The following window appears.

If the FTvirtual Server LAN cable is not connected

to the HUB, an error, as shown in the ﬁgure above,

will be displayed but this does not indicate an error.

Continue operations.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click [OK] to close the [Component Prop-

erties] window and Endurance Manager

will end.

Right-click on the FTvirtual Server icon

and select "Properties".

The [Component Properties] window appears.

Set IP addresses for the following adapt-

ers.

Because DHCP is preset to automatically acquire

IP addresses, if these IP addresses are acceptable

the following procedures are not required.

- CoServer1 "CoServer Management"

- CoServer2 "CoServer Management"

- FTvirtual Server "Local Area Connection"

"Redirected0" in CoServer1 and CoServer 2 has

been reserved for use by FTvirtual Server. Do not

bind internet protocol (TCP/IP) to these adapters.

Set the FTvirtual Server LAN IP address and the

subnet mask on the FTvirtual Server.

If optional devices have been added

before running mini-setup of the OS,

refer to the following and perform op-

erations after expansion.

- When a 5-inch internal backup device is add-

Select "FTvirtual Server" from the tree

on the left, check "enabled" in "Auto-

matic start" and click [Apply].

"5.8.4 Procedure after Installing

the Internal Backup Device"

��

A red warning message will appear in the top of the

properties window but it just indicates a change in

properties and will have no effect on operations.

Turning the server off

Perform shutdown in the FTvirtual Server window using the following procedures.

Click [Start]

[All Programs]

thon Endurance] [Management

Tasks] [Endurance Conﬁguration]

[Shutdown] in this order.

[Mara-

When turning on the server again after turning it off,

wait for at least ten seconds and then press the power

switch.

If the server is turned on straight after being turned

off, an error will occur that may be cause damage.

A dialogue box for conﬁrming shutdown will ap-

pear.

Click [OK].

After shutting down FTvirtual Server, shutdown

CoServer1 and CoServer2 and the power supply

will be turned off automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the remaining LAN cables

After turning off the server, connect the remaining LAN cables as described below.

In the FT-system, all FTvirtual Server LAN (application data transmission), CoServer Link, and CoServer LANs

are used to control the system so it is important not to forget to connect the CoServer LAN cable to a HUB.

●Connecting the LAN cables

��

Support and Service

PRIMERGY information

The latest PRIMERGY, driver, and software information is

available at the address below. Use as necessary.

http://primergy.fujitsu.com

Pre-operation settings

After running mini-setup of the OS, refer to the

following and perform FT-system settings.

"Chapter 3 Pre-operation Settings"

��

Before requesting repairs

When using UPS, perform UPS settings.

If an error occurs in this server, refer to "User's Guide 7.2

Troubleshooting". If problems can still not be solved, con-

tact an ofﬁce listed in the "Contact Information".

When contacting the ofﬁce listed in the "Contact Informa-

tion", inform them of the product ID and manufactures

number which are detailed on labels on the base of the

server.

"3.4 UPS setting"

��

For details about maintenance after operations have

started, refer to "User's Guide Chapter 7 Operation

and Maintenance".

��

�

��

�

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Also read the points to note about requesting repairs be-

forehand in "User's Guide 7.10.2 Contacting Maintenaice

Support".

Print the "Conﬁguration Sheets" - "Accident Sheet" and en-

ter the checked information.

Be careful not to lose this sheet, as you must provide this

information when you contact an ofﬁce listed in the "Con-

tact Information" your maintenance engineer.

- Service life of non-durable components

The service life of non-durable components is decided based

on the presumption that the server is used in an appropriate

environment.

The temperature of the operating environment is between

10 and 35

°C °C.

However, the service life is calculated using

25 as the average temperature so air conditioning should be

°C

used.

Non-durable components

- Non-durable component

Depending on the environment and period of usage there will

be non-durable components that require replacement within

the warranty period. Customers who have signed up to hard-

ware maintenance contract will be provided with replacement

parts free of charge and will have higher priority for replace-

ment.

Item

SCSI Array

Description

Regardless of how long power has been turned on

Controller card or off, a replacement message will appear for non-

battery durable components after 3 years.

Customers not signed up to hardware maintenance contract

will be charged for operation cost (including the maintenance

parts) replacement separately.

Recycling

When disposing of this server, contact an ofﬁce listed in the "Contact Information".

This server must be disposed of as industrial waste.

Contact Information

Australia:

Philippines:

Fujitsu Philippines, Inc.

Tel: +63-2-812-4001

Fax: +63-2-817-7576

Address: 2nd Floor, United Life Building, A. Arnaiz

Legaspi Village, Makati, Metro Manila Philippines

Singapore:

Fujitsu Asia Pte. Ltd.

Tel: +65-6777-6577

Fujitsu Australia Limited

Tel: +61-2-9776-4555

Fax: +61-2-9776-4556

Address: 2 Julius Avenue (Cnr Delhi Road)

North Ryde, Australia N.S.W. 2113

China:

Fujitsu (China) Holdings Co., Ltd.

Tel: +86-21-5292-9889

Fax: +86-21-5292-9566

Address: 18F, Citic Square, 1168 West Nanjing Road Shanghai, China

200041

Fax: +65-6771-5502

Address: 20, Science Park Road, #03-01 TeleTech Park,

Singapore Science Park II, Singapore 117674

Taiwan:

Fujitsu Taiwan Limited

Tel: +886-2-2311-2255

Fax: +886-2-2311-2277

Address: 19F, No.39, Section 1, Chung hwa Road Taipei, Taiwan

Thailand:

Fujitsu Systems Business (Thailand) Ltd.

Tel: +66-2-500-1500

Fax: +66-2-500-1555

Address: 12th Floor, Olympia Thai Tower, 444 Rachadapisek Road

Samsennok, Huaykwang, Bangkok, Thailand 10310

Vietnam:

Fujitsu Vietnam Limited

Tel: +84-4-831-3895

Hong Kong:

Fujitsu Hong Kong Limited

Tel: +852-2827-5780

Fax: +852-2827-4724

Address: 10/F., Lincoln House, 979 King's Road

Taikoo Place, Island East, Hong Kong

Indonesia:

PT. Fujitsu Systems Indonesia Ofﬁces Headquarters

Tel: +62-21-570-9330 (Hunting)

Fax: +62-21-573-5150

Address: Wisma Kyoei Prince 10th Floor Jl. Jend. Sudirman Kav 3-4

Jakarta, Indonesia 10220

Korea:

Fujitsu Korea Ltd.

Tel: +82-2-3787-6000

Fax: +82-2-3787-6066

Address: Susong Tower Building, 83-1 Susong-Dong

Jongno-Gu, Seoul, Republic of Korea 110-140

Malaysia:

Fujitsu (Malaysia) Sdn. Bhd.

Tel: +60-3-8318-3700

Fax: +84-4-831-3898

Address: Unit 802-8th ﬂoor, Fortuna Tower Hanoi 6B Lang ha Street,

Ba dinh District, Hanoi Socialist Republic of Vietnam

United States:

Fujitsu Computer Systems Corporation

Tel: +1-800-831-3183

Fax: +1-408-496-0575

Address: 1250 East Arques Avenue, Sunnyvale, CA USA 94088-3470

Fax: +60-3-8318-8700

Address: 1st Floor, No.3505 Jalan Technokrat 5

63000 Cyberjaya, Selangor Darul Ehsan Malaysia

For the latest information, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

Data Backup

To protect data stored in this device (including basic software and application software), perform backup and other necessary operations. Note that data protection is

not guaranteed when repairs are performed. It is the customer's responsibility to maintain backup copies in advance.

In case of data loss, Fujitsu assumes no liability for data maintenance or restoration and damages that occur as a result of the data loss for any reason, except for items

covered under warranty.

High Safety

The Products are designed, developed and manufactured as contemplated or general use, including without limitation, general ofﬁce use, personal use, household use,

and ordinary industrial use, but are not designed, developed and manufactured as contemplated for use accompanying fatal risks or dangers that, unless extremely high

safety is secured, could lead directly to death, personal injury, severe physical damage, or other loss (hereinafter "High Safety Required Use"), including without limi-

tation, nuclear reaction control in nuclear facility, aircraft ﬂight control, air trafﬁc control, mass transport control, medical life support system, missile launch control

in weapon system. You shall not use this Product without securing the sufﬁcient safety required for the High Safety Required Use. If you wish to use this Product for

High Safety Required Use, please consult with our sales representatives in charge before such use.

Problems may occur with this device in the event of an instantaneous voltage drop of the power supply due to lightning, etc. To prevent an instantaneous voltage drop

of the power supply, we recommend that you use an uninterruptible power supply system.

Software License Agreement

Please read the following terms and conditions before you use the software preinstalled in the server you purchased or the software attached to the server (hereinafter

collectively "Software"). By using the Software, you are agreeing to be bound by all of the following terms and conditions. Notwithstanding the foregoing, if any soft-

ware subject to any other terms and conditions than those of this agreement is preinstalled in or attached to the server as a part of Software, you shall comply with such

other terms and conditions.

I. License and Copyrights

Fujitsu Limited (hereinafter "Fujitsu") grants you a limited, non-exclusive, license to:

(i) use the Software solely on the server, which the Software is preinstalled in or is attached to.;

(ii) copy the Software for installation and backup purpose; and

(iii) embed the Software to other software, in whole or in part, in accordance with the procedure described in the applicable documentation.

For the avoidance of doubt, you are only granted the right to use this Software and all copyright, title and other ownership rights to this Software and any derivative

works thereof is retained by FUJITSU and/or its suppliers.

II. Copies

1. You may only copy the Software as set forth in Clause I (ii) and (iii) above. If you embed the Software in another software pursuant to Clause I (iii), you may not

make copies of such software as so embedded other than one (1) backup copy unless expressly otherwise licensed by Fujitsu. If, however, a copy protection mechanism

is implemented in the Software, you cannot and are prohibited from making any copies of the Software.

2. You shall include all copyright notices and proprietary legends on all copies of the Software and shall not modify, delete or conceal such notices and legends.

3. All terms and conditions contained herein shall apply to the copies of the Software.

III. Assignment

You may not assign the Software, except the case where you assign the Software with all materials related to the Software, including the media of the Software attached

to the server, the documentation, and the backup copy, together with the server. Notwithstanding the foregoing, you may not rent, lease, sublicense, create lien against

the Software.

IV. Modiﬁcation

You may not modify or, except to the extent expressly permitted by applicable law, reverse engineer (including, without limitation, decompile and disassemble) the

Software, and you may not permit any third party to do so.

V. Limited Warranty

1. You acknowledge that Fujitsu cannot guarantee that your use of the Software will be uninterrupted, that the Software will be error free or that all Software errors

will be corrected. However, (i) within ninety (90) days following your acquisition of the server you notify the reseller from whom you have acquired the server of non-

conformance of the Software to the description in the documentation, or (ii) within one (1) month following your acquisition of the server you notify the reseller from

which you have acquired the server of physical defects of the media containing the Software, Fujitsu will, at its sole discretion, correct the non-conformance or provide

you with information necessary to correct the non-conformance, or replace the defective media with new media. Only if you inform such reseller of your problem with

the Software during the above mentioned warranty period and provide satisfactory evidence of the date you acquired the server Fujitsu will be obligated to honor this

warranty.

2. Except for Clause V Section 1, Fujitsu disclaims all other warranty, express or implied, and expressly disclaims any implied, including without limitation, allwar-

ranty of merchantability, ﬁtness for a particular purpose or non-infringement of third parties' rights. In no event will Fujitsu be liable for any direct, indirect, incidental

or consequential damages (including, but not limited to, loss of proﬁts, interruption of business, loss of business information, and other pecuniary damages) resulting

from or arising out of the use or inability to use the Software even if Fujitsu has been advised of the possibility of such damages.

3. Even if a part of the Software has been developed by a third party, the warranty and remedy for such part of the Software are limited to those provided for in Clause

V Section1 and 2 above, and such third party shall have no liability for any claim arising out of the use, performance or non-conformance of the Software.

VI . Law

This Agreement and all matters arising out of or relating to this Agreement will be governed by the laws of Japan without giving effect to any choice of law rule.

VII. High Safety

These Software are designed, developed and manufactured as contemplated for general use, including without limitation, general ofﬁce use, personal use, household

use, and ordinary industrial use, but are not designed, developed and manufactured as contemplated for use accompanying fatal risks or dangers that, unless extremely

high safety is secured, could lead directly to death, personal injury, severe physical damage, or other loss (hereinafter "High Safety Required Use"), including without

limitation, nuclear reaction control in nuclear facility, aircraft ﬂight control, air trafﬁc control, mass transport control, medical life support system, missile launch con-

trol in weapon system. You shall not use this Software without securing the sufﬁcient safety required for the High Safety Required Use.

VII Export

You shall comply fully with all relevant export laws and regulations with respect to this Software, including, but not limited to, the export laws and regulations of Ja-

pan. Without limiting the generality of the foregoing, You will not export or transfer this Software, or any product thereof (including any your application program), to

any destinations prohibited by any such laws and regulations.

IV. Entire Agreement

The terms and conditions hereof represent the complete agreement concerning this license between the parties and supersede all prior or contemporaneous written

communications between them. In the event that any additional terms or conditions are provided in the accompanied documentation, you must also comply with such

terms and conditions.

Fujitsu Limited

Microsoft, Windows, Windows Server are registered trademarks of the Microsoft Corporation in the USA and other countries.

Adobe, Adobe Acrobat, Acrobat Reader are registered trademarks of Adobe Systems Incorporated.

Endurance, Marathon Assured Availability, SplitSite, Marathon FTvirtual Server, and the Marathon logo are either registered trademarks or trademarks of

Marathon Technologies Corporation in the United States and/or other countries.

Other product names used are trademarks or registered trademarks of their respective manufacturers.

Other products are copyrights of their respective manufacturers.

このマニュアルはリサイクルに配慮して製本されています。

不要になった際は、回収・リサイクルに出してください。

Screen shot(s) reprinted with permission from Microsoft Corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Dynex TV Video Accessories DX WD1201 User Manual
Echo Trimmer PPFD 2400 User Manual
Edimax Technology Network Card LAN USB Adapter User Manual
Exido Scale 246 020 User Manual
Extreme Networks Switch 12800 Series User Manual
Frigidaire Washer FWX223LB User Manual
GE Appliance Trim Kit SESO732 User Manual
GE Monogram Range JBS08PIC User Manual
Golden Technologies Mobility Scooter GB106 User Manual
Goodman Mfg Air Conditioner 000 &12 User Manual