FREECOM Network MediaPlayer
Drive-In Kit
MANUAL
Rev. 520
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Users manual
GB
General Information .......................................................................... page
Warnings and Safety Instructions ..................................................... page
Product Overview ............................................................................... page
4
6
8
Chapter 1:
Use as External USB HDD ................................................................... page 10
Chapter 2:
Access PC via Network ....................................................................... page 31
Chapter 3:
Use as Multimedia Player .................................................................. page 49
Technical Specifications ..................................................................... page 77
© 2005 Freecom Technologies
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
Introduction
GB
•
Dual Data Access Mode via 10/100Mbps LAN and 3.5" HDD (when assem-
bled in the device)
•
•
•
•
•
•
Digital Multimedia Player via Home TV or Car TV
USB 2.0 External Storage via PC (NTFS, FAT32)
Audio - Stereo, Digital Coaxial & Optical 5.1ch. Sound
Video - Composite, S-Video, HD Component 480p, 720p, 1080i
DVD Manager - Playback of DVD File same as Original DVD Title
Firmware upgradeable.
Package Content
Please check the contents of the box. The following should be supplied:
•
•
•
•
•
•
•
Freecom Network MediaPlayer-35 drive in kit, footstand
Remote Control & Battery
Composite + Stereo L-R Cable
USB Cable
LAN Cable
Power Adapter
CD with manual and, USB 2.0 Driver for WIN98SE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
Minimum System Requirements
USB Requirements
GB
•
•
Windows98SE, ME, 2000, XP/MACOSX10.1orhigher/Linux2.4.xorhigher
Available USB 2.0, 1.1 Port (USB 2.0 recommended)*
Network Requirements
•
•
•
Windows 98SE, ME, 2000, XP
Available 10/100 Ethernet LAN Port, RJ-45 (100Mbps recommended)
LAN Cable (cross-wired or standard - see Page 28 2.1)
Hardware Requirements
•
•
•
•
•
•
Pentium III 500MHz or faster
At least 128 MB RAM
USB interface (USB 1.1 or USB 2.0*)
A CD-ROM drive or internet connection for driver installation
For playback on TV, a TV with PAL or NTSC system is required.
Support HDD: Compatible with standard 3.5" IDE Hard Drive
*
USB 2.0 is downwards compatible to USB 1.1. To achieve optimal performance from the
Freecom Network MediaPlayer-35 drive in kit your PC should be equipped with an USB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
Precautions
GB
•
We strongly recommend you to regularly back up the data from the hard
drive that you have built in, to another safe media. Freecom can never be
held responsible for data damage or data loss of the built-in HDD.
•
•
Unplug the power adaptor when you don't use the device for a longer
period time.
The device does not support DivX, XviD codec of video files that has GMC,
Qpel option.
•
•
Do not turn off the power when a file is playing.
We recommend (when connected to PC) that you use a USB cable not longer
than 3 meters.
•
•
If you have USB 1.1 Host Adapter, the device will be working at USB1.1
speed.
When using a hard drive with less than 6GB storage capacity, you may
experiencedatadamageordataloss. Werecommendyoutouseaharddrive
of more than 6GB.
Note: Be sure to format the Hard Drive before using the device.
When you use an unformatted HDD, a PC will not detect the
device.
Warnings and Safety Instructions
Please read and follow the below mentioned instructions. They should be
observed in order to prevent injury to the user, damage to the device and
damage to property, as well as to ensure safe use of the product. Not following
these instructions may cause the unit to malfunction.
To ensure that your Freecom Network MediaPlayer-35 drive in kit functions
properly, please take note of the following precautions. If these are not
followed, you may void your warranty and damage the Freecom Network
MediaPlayer-35 drive in kit.
•
Safely remove the Freecom Network MediaPlayer-35 drive in kit via your
operating system (the "unplug or eject hardware" option in the Windows
taskbar) before disconnecting the USB cable or power cable and before
switching off the device. Failing to do so may result in data loss.
•
Do not disconnect the Freecom Network MediaPlayer-35 drive in kit from
the PC during file transfer. This may result in data loss and an error on the
player. If this occurs, please run the ScanDisk utility.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Safety Instructions
•
Do not drop the Freecom Network MediaPlayer-35 drive in kit or expose it
to other kinds of sudden mechanical shocks as this may result in data loss
and damage to the hard drive.
GB
•
•
Do not use the Freecom Network MediaPlayer-35 drive in kit when the
ambient temperature is below 10°C or above 45°C.
If the Freecom Network MediaPlayer-35 drive in kit is moved from a cool
environment to a warmer environment, please allow the drive to acclima-
tize to the ambient temperature before operating the device. Failing to do
so may lead to condensation within the drive enclosure, which in turn may
cause the drive to malfunction.
•
•
Do not place liquids or drinks on the Freecom Network MediaPlayer-35
drive in kit. When liquids are spilled and get in contact with the electronics
within the drive enclosure, it will damage the drive and will cause the drive
to malfunction.
Do not use the Freecom Network MediaPlayer-35 drive in kit in a dusty
environment. Dust inside the enclosure may damage the internal electron-
ics and result in drive malfunction.
•
•
•
Do not use the Freecom Network MediaPlayer-35 drive in kit near magnetic
fields.
Opening the Freecom Network MediaPlayer-35 drive in kit will void the
warranty.
The Network MediaPlayer-35 drive in kit may generate heat when used for
a longer period of time.
Furthermore, warranty does not apply to:
•
•
Damages or problems resulting from misuse, abuse, accident, alteration or
incorrect electrical current or voltage.
Any product tampered-with or damaged warranty seal or serial number
label.
•
•
Any product without a warranty or serial number label.
Batteries and any consumable items delivered with or in the equipment.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
Product Overview
GB
1. FRONT VIEW
All basic operation functions can be done with the buttons on the device
without use of the remote control.
Enter
Power
Stop / Init
Play / Pause
IR
PWR
NET
HDD
ENTER
Select or play a file
Navigation Key, Up, Down, Left, Right
Power On, Off
POWER
PLAY / PAUSE Play all files from selected file / Pause
STOP / INIT
IR
Stop / Return to Mode Selection Screen
IR receiving area for remote signals
Power LED
PWR
NET
Network LED
HDD
HDD LED
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
2. BACK VIEW
GB
IR-EXT
USB
Optical
CVBS
S-Video
Coaxial
Stereo L - R
Y. PB. PR
LAN
PWR
IR-EXT
USB
Connect external remote control IR receiver
Connect USB cable
OPTICAL
S-VIDEO
COAXIAL
Y, PB, PR
LAN
Connect Optical cable for 5.1 ch. digital audio output
Connect s-video for video output
Connect coaxial cable for 5.1 ch. digital audio output
Connect component Y, Pb, Pr cable for video output
Connect lan cable for networking
PWR
Connect power cable
CVBS
Connect composite cable for video output
Connect stereo cable for audio output
STEREO L-R
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
Chapter 1: Use as External USB HDD
GB
1
1.1 Insert Hard Disk
•
•
Only use a 3.5" IDE Hard Disk for Desktop.
Hard Disk should be jumpered as "Master". However, if the Hard Disk
supports "Single" mode, you need to try to set "Single "mode.
1. Unscrew the 4 screws and open the cover by
sliding it in the direction of the arrow
2. Connect Power and IDE 40-pin connector to
Hard Disk.
3. Close the cover by sliding it in the direction
of the arrow.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
4. Put the 4 screws back
GB
1
1.2 Connecting the player to the PC
1. Connect the USB cable to the player and connect the power adapter to the
DC jack on the player.
2. Connect the adapter into an AC outlet.
3. Connect the player to the PC's USB port.
4. Switch the power on by pressing the power on-off button on the player
5. Windows 2000 and Windows XP will recognize the player as a USB drive
automatically; you can use the player without installing a driver.
Note: foruseunderWindows98SE, youhavetoinstalltheUSB2.0
driver from the manual CD.
6. Iftheplayerisnotrecognizedordetected, pleasecheckiftheUSBconnector
is properly connected to the device and the PC.
1.3 Format the Built-in HDD via USB
If the assembled HDD is not formatted, a PC will not detect the hard disk drive.
If your harddisk is not formatted,follow the below mentioned instructions. If
the hard disk drive is already formatted, you can discard below steps and go to
"1.4 Copy Data via USB".
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
File System features
GB
1
Please refer to the tables below for an overview:
File systems supported by different operating systems
File system
FAT
FAT32
NTFS
Operating system
Windows 98SE
yes
yes
not supported
Windows ME
Windows 2000
Windows XP
yes
yes
yes
yes
yes
yes
not supported
yes
yes
Maximum size of a partition
File system
FAT
FAT32
NTFS
Operating system
Windows 98SE
Windows ME
Windows 2000
Windows XP
2 GB
60 GB *1, 2
2 TB *2
32 GB
n.a.
2 GB
n.a.
4 GB *3
4 GB *3
16 TB
16 TB
32 GB
Example for different partitions with different file systems on one Network
MediaPlayer-35 drive in kit
File system
NTFS
FAT32
Total size of the Drive
120 GB
90GB
30 GB
The example above is a good solution for Windows 2000/XP users who
sometimes exchange data with Windows 98SE/ME PCs.
For storing the data under Windows 2000/XP both partitions can be used. As
the NTFS file system is not recognized by Windows 98SE/ME data to be used on
these operating systems must be stored on the FAT32 partition.
Please follow the steps below to adapt the Network MediaPlayer-35 drive in kit
for your needs.
*1: A patch for Windows 98SE is required for hard disk larger than 60 GB. Further information and
an update to fix this problem can be found in article 263044 of the "Microsoft Knowledge
*2: Hard disk capacity will not be displayed correctly by fdisk!
*3: FAT partitions larger than 2 GB can only be administrated by Windows 2000/XP.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
1.3.1 Partitioning your Network MediaPlayer-35 drive in kit under
Windows 98SE / Windows ME
GB
1
Windows 98SE only: The fdisk version which is installed together with your
operating system does not recognize the correct size of hard disks larger than
64 GB.
Windows 98SE/ME: For large partitions fdisk will not display the partion size
correctly! Please ignore this as the partitioning results will still be OK.
Further information and an update to fix this problem can be found in article
263044 of the "Microsoft Knowledge Base"on the Microsoft Website under
Creating a partition on the Network MediaPlayer-35 drive in kit under
Windows 98 SE / ME
The following steps will guide you the process of creating partitions on your
Network MediaPlayer-35 drive in kit under Windows 98SE/ME. After this
procedure your Freecom Network MediaPlayer-35 drive in kit will be ready for
use and it will be allocated a drive letter.
1. Click on the "Start" button.
2. Select "Run".
3. Enter "fdisk" and confirm with "OK".
4. Answer the question "Do you wish to enable large disk support?" by
pressing the 'Return' key. FAT32 is now activated.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
5. Choose Option "5 (Change current fixed disk drive)" by pressing '5' and
'Return'.
GB
1
6. Select the hard disk by its number where the "Usage" contains no value but
only a percent symbol. Select the number of the corresponding hard disk
and confirm by pressing the "Return" key.
Now your hard disk is activated and ready to be partitioned.
Note: Partition size of large hard disks will not be displayed
correctly! However partitioning results will be OK.
7. Select Option 1 "(Create DOS partition or Logical DOS drive)" by pressing
'1' and confirm with 'Return'.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
8. Select Option 1 "(Create primary DOS partition)" by pressing '1' and
confirm with 'Return'.
GB
1
Wait until drive integrity is completely checked.
9. If only one partition is required then answer "Y" to the question: "Do you
wish to use the maximumavailable size for a Primary DOS partition?" If
more than on partition is required go to the next section "Create two or
more partitions on the Network MediaPlayer-35 drive in kit under Windows
98 / Windows ME".
Now the whole disk will be partitioned as one primary partition. Wait until
the drive integrity check is completed.
10. Press the 'ESC' key to return to the fdisk options.
11. Now press the 'ESC' key to close the "fdisk window". Your hard disk is now
partitioned.
12. Stop your hard disk by using the hot unplug icon in the lower right corner
of your screen and remove the USB cable from your hard disk. Afterwards
connect your hard disk again with your computer. The hard disk will now
be recognized by Windows.
As Windows tries to access your hard disk an error message will appear. This
happens, because your hard disk is not yet formatted.
Creating two or more partitions on the Network MediaPlayer-35
drive in kit under Windows 98SE / ME
1. Repeat steps 1 to 7 from the previous chapter (Create one partition on the
Network MediaPlayer-35 drive in kit under Windows 98SE/Windows ME).
2. Answer the question "Do you wish to use the maximum available size for
a primary DOS partition?" with "N".
3. Enter either the size or a percentage value for the partition size. Press
'Return' and wait until the drive integrity check is completed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
4. Press the 'ESC' key to return to the fdisk options.
GB
1
5. Select Option 1 "(Create DOS partition or Logical DOS drive)" by pressing
'1' and confirm with 'Return'.
6. Select Option 2 "(Create Extended DOS Partition)" by pressing '2' and
confirm with 'Return'. Wait until the drive integrity check is completed.
7. Enter either the size or a percentage value for the partition size or press
'Return' to accept the default value.
8. Press 'ESC' to return and wait until the drive integrity check is completed.
9. A logical drive needs to be defined now. Enter the size of the logical drive
and press 'Return' or accept the default value by pressing 'Return'.
10. Press 'ESC' to return to the fdisk options.
11. Now press the 'ESC' key to close the "fdisk window". Your hard disk is now
partitioned.
12. Stop your hard disk by using the hot unplug icon in the lower right corner
of your screen and remove the USB cable from your hard disk. Afterwards
connect your hard disk again with your computer. The hard disk will now
be recognized by Windows.
As Windows tries to access your hard disk an error message will appear. This
happens, because your hard disk is not yet formatted.
Formatting partitions on the Network MediaPlayer-35 drive in kit
under Windows 98SE / ME
1. Double-click on the "My Computer" icon on your desktop.
2. Click with the right mouse button on the drive symbol of your Network
MediaPlayer-35 drive in kit. Now a menu will appear where you can choose
the option "Format".
3. Please perform a complete formatting of your drive. You can also assign a
name to your drive here.
4. After you have completed your selection, click on "Start".
Attention: Selecting the wrong drive will lead to a loss of your
data. Please ensure that the correct drive is selected!
5. Confirm the next message with "OK".
6. Afterformattingisfinishedyoucanperformadiskscan. Todoso, followthe
instructions of the Windows Help system. If you don't want to scan your
disk, just close the message window.
Repeat these steps for each partition if more than one partition was
created.
Now your Network MediaPlayer-35 drive in kit is ready for use. You can use
it like an internal hard disk for storing your data.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
Deleting a partition on the Network MediaPlayer-35 drive in kit under
Windows 98SE / ME
GB
1
The following steps will explain how to delete a partition on your Network
MediaPlayer-35 drive in kit.
1. Click on the "Start" button.
2. Select "Run".
3. Enter "fdisk" and confirm with "OK".
4. fdisk will be started. Answer the question "Do you wish to enable large disk
support?" by pressing the 'Return' key. FAT32 is now activated.
5. Choose Option 5 "(Change current fixed disk drive)" by pressing '5' and
'Return'.
6. Select the hard disk to be deleted by its number. ATTENTION: Please make
sure that the correct drive is selected. Selecting the wrong drive will lead to
a loss of your data!
7. Choose Option "3 (Delete partition or Logical DOS Drive)" by pressing '3'
and 'Return'.
8. Select the partition to be deleted by pressing its number and 'Return'.
9. Enter the drive label and press 'Return'.
10. Confirm with 'Y' and 'Return' to delete the partition.
11. Press the 'ESC' key to return to the fdisk options.
12. Press 'ESC' to exit fdisk. Stop your hard disk by using the hot unplug icon in
the lower right corner of your screen and remove the USB cable from your
hard disk. Afterwards connect your hard disk again with your computer.
The hard disk will now be recognized by Windows.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
1.3.2 Partitioning your Network MediaPlayer-35 drive in kit under
Windows XP / 2000
GB
1
Creating a partition on the Network MediaPlayer-35 drive in kit
under Windows XP / 2000
The following steps will guide you through the process of creating partitions
on your Network MediaPlayer-35 drive in kit. After this procedure your
Freecom Network MediaPlayer-35 drive in kit will be ready for use and it will
be allocated a drive letter.
1. Click with the right mouse button on the "My Computer" icon on your
desktop.
2. Select the option "Manage".
3. Select the option "Storage" -> "Disk Management".
4. Choose the hard disk, which is "unallocated". Ensure that the entire drive
is "unallocated".
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
5. Click with the right mouse button on the "unallocated" area and select the
option "New Partition" (Windows 2000: "Create Partition Wizard"). The
"New Partition Wizard" opens. Click on "Next".
GB
1
6. Select "Primary partition" and click on "Next".
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
7. Now you can adjust the size of your partition. Click on "Next" if only one
partition is to be created. See next chapter (Creating two or more partitions
on the Network MediaPlayer-35 drive in kit under Windows XP/2000) how
to create more than one partition.
GB
1
8. Assign a drive letter to your hard disk. Normally you can use the default
options. Click on "Next".
9. Select the formatting option. Choose either "FAT32" or "NTFS", the
"Allocation Unit Size" should remain on "Default". Finally select "Perform
Quick Format" and click on "Next".
10. Clickon"Finish"tocompletethepartitioningofyourNetworkMediaPlayer-
35 drive in kit. Your Network MediaPlayer-35 drive in kit will be formatted
now and is ready-to-use afterwards.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
GB
1
Creating two or more partitions on the Network MediaPlayer-35
drive in kit under Windows XP / 2000
1. Repeat the steps from the previous chapter (Creating a partition on the
Network MediaPlayer-35 drive in kit under Windows XP/2000) for creating
the first partition.
2. Click with the right mouse button on the "My Computer" icon on your
desktop.
3. Select the option "Manage".
4. Select the option "Storage" -> "Disk Management".
5. Right-click on the unallocated space of your Network MediaPlayer-35 drive
in kit and select the option "New partition" (Windows 2000: "Create
partition"). The "New Partition Wizard" (Windows 2000: "Create Partition
Wizard") opens. Click on "Next".
6. Select "Extended partition" and click on "Next".
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
7. Now you can adjust the size of your partition. Enter the size and click on
"Next".
GB
1
8. Click on "Finish" to create the "Extended partition". The unallocated space
now changed to "Free space".
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
GB
1
9. Right-click on "Free Space" and select "New Logical Drive" (Windows 2000:
"Create Logical Drive"). The "New Partition Wizard" (Windows 2000:
"Create Partition Wizard") opens. Click on "Next".
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
10. "Logical drive" is already selected. Click on "Next".
11. Specify the partition size and click on "Next".
12. Assign a drive letter and click on "Next".
GB
1
13. Select the formatting option. Choose either "FAT32" or "NTFS", the
"Allocation Unit Size" should remain on "Default". Finally select "Perform
Quick Format" and click on "Next".
14. Click on "Finish" to complete partitioning. Your partition will be formatted
now and is ready-to-use.
Deleting a partition on the Network MediaPlayer-35 drive in kit
under Windows XP / 2000
1. Click with the right mouse button on the "My Computer" icon on your
desktop.
2. Select the option "Manage".
3. Select the option "Storage" -> "Disk Management".
4. Choose your external hard drive and right-click on the partition.
5. Select "Delete Partition" and confirm by clicking on "Yes". The partition
will be deleted now.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
1.4 Copy Data via USB
GB
1
You can use the device as an external USB hard drive when you have assembled
a hard disk into it. You can copy data from your PC to the built-in HDD of the
player via USB. These files (when they are audio, video or photos) you can play
back directly from the device on a TV or HiFi set.
When connecting to PC, you have to connect the power cable to
a power outlet.
1.4.1 Windows 98SE
First, you have to install Windows 98 Driver before connecting PC.
•
Insert the Manual & Application CD into your CD drive. The
Freecom start menu opens. (In case the software does not
open automatically, please click on "Start" in the main direc-
tory of the CD.)
•
Click on "Driver (Win 98)".
After finishing installation, connect the player to the PC via USB
cable, and plug power cable to a power outlet.
1. After installing the driver, connect the player and plug power cable. And
then, check the driver installation at Windows [Start > Settings > Control
Panel > System > Device Manager > Hard disk controllers > Hi-Speed USB-
IDE Bridge Controller].
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
2. Check 'My Computer' or 'Explorer', there should be a new volume. You can
copy any data to this volume.
GB
1
If a new volume does not appear, check if the HDD is formatted,
and check the HDD file system. Windows 98SE can only detect
FAT32 file system.
3. After copying data, remove the player using remove icon
from the
Windows taskbar. Not following this procedure may cause data loss and
damage to the harddrive.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
1.4.2 Windows ME
GB
1
1. After connecting the player and plugging the power cable, Windows will
automatically install the driver. After this, please check the driver installa-
tion at Windows [Start > Settings > Control Panel > (view all Control Panel
options) > System > Device Manager > Universal Serial Bus controllers > USB
Mass Storage Device]
2. Check 'My Computer' or 'Explorer', there should be a new volume. You can
copy any data to this volume.
If a new volume does not appear, check if the HDD is formatted
or not, and check the HDD file system. Windows Me can only
detect FAT32 file system.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
3. After copying data, remove the player using the remove icon
from the
GB
1
Windows taskbar. Not following this procedure may cause data loss and
damage to the device.
1.4.3 Windows 2000, XP
1. After connecting the player and plug power cable, Windows will automati-
cally install the driver. After this,please check the driver installation at
Windows [Start > Settings > Control panel > (switch to classic View on
Windows XP) > system > Hardware > Device manager > Universal Serial Bus
controllers > USB Mass Storage Device ].
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
2. Check 'My Computer' or 'Explorer', there should be a new volume. You can
copy any data to this volume.
GB
1
If new volume is not be appeared, check if HDD is formatted.
Windows 2000, XP can detect both FAT32 and NTFS file system.
3. After copying data, remove the player using remove icon
from the
Windows taskbar. Not following this procedure may cause data-loss or
damage to the player.
When you see 'Non High-Speed USB Hub Message':
ThismessagewillbedisplayedinWindowsXPwhenyouplugthe
player into a USB 1.1 spec. Host adapter port.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
1.4.4 Linux
GB
1
[Automatic Mount]
After booting, do log-in.
Connect the Network MediaPlayer-35 drive in kit -> Power On the Network
MediaPlayer-35 drive in kit -> Check the detection with [fdisk] -> make Mount
Pointer (ex. mediatest) at Folder Mount(/mnt) -> Edit [/etc/fstab] -> add the
following:
•
•
/dev/sda /mnt/mediatest vfat noauto, user 0 0 (in case of FAT32 HDD)
/dev/sda /mnt/mediatest ntfs noauto, user 0 0 (in case of NTFS HDD)
Do Log-in again.
Aboveexample"sda"isassumedthattheNetworkMediaPlayer-
35 drive in kit will be detected as "sda" on your system. If not,
you have to write the drive name which is detected as "USB Mass
Storage", not "sda".
[Manual Mount]
Connect the Network MediaPlayer-35 drive in kit -> Power On the Network
MediaPlayer-35 drive in kit -> Check the detection with [fdisk] -> make Mount
Pointer (ex. mediatest) at Folder Mount(/mnt) -> Edit [/etc/fstab] -> add the
following:
•
•
mount –t vfat /dev/sda /mnt/mediatest (in case of FAT32 HDD)
mount –t ntfs /dev/sda /mnt/mediatest (in case of FAT32 HDD)
Aboveexample"sda"isassumedthattheNetworkMediaPlayer-
35 drive in kit will be detected as "sda" on your system. If not,
you have to write the drive name which is detected as "USB Mass
Storage", not "sda".
[How to stop using]
Do [unmount] at Device Control.
1.4.5 Mac
There is no need to install a MAC installation driver, the player will be detected
automatically. If the player is detected correctly, an icon will appear on your
desktop.
When removing the player, drag the icon to the trash-can on your desktop and
unplug the device.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as External USB HDD
Chapter 2: Access PC via Network
GB
1
2.1 Connect LAN Cable
When connecting Computer to the Network MediaPlayer-35 drive in
kit directly
Connect LAN cable to LAN port between player and PC. In this case, you have
to use a Cross-wired LAN cable.
[TIP] If your computer's LAN card is already used for connection to Internet
line, you can install an additional LAN card to your PC and connect that
additional LAN card to the player.
When connecting with IP Router or Hub
Connect LAN cable to LAN port between IP Router or Hub. In this case, you have
to use a standard LAN Cable.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
2.2 Set Network Configurations
GB
2
After connecting the LAN cable, you have to set network configurations of
Computer and Player. You need to share a folder on Windows computer and
use same 'IP Address range' and same 'Subnet Mask ' between Windows
computer and Player. For example:
Computer
Network MediaPlayer-35
drive in kit
IP Address
192.168.1.2
192.168.1.3
Subnet Mask
255.255.255.0
255.255.255.0
It is possible to assign IP address and Subnet Mask of the player
as Dynamic or Static.
2.2.1 Windows 98SE, ME
1. Select a folder you want to share. Right-click the folder and click 'sharing'
in pop-up menu.
2. Check 'Shared as' and write 'Share Name'. For example, "My Movie"
•
•
•
"Share Name": maximum length is 12 characters.
We recommend to check 'Read Only' at 'Access Type'
Do not use the password option
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Access PC via Network
GB
2
3. After that, the shared folder will be displayed like in following picture.
4. Move to [Control panel > Network], and double click 'TCP/IP->LAN card'
that you want to use on your computer.
In order to see LAN Card name, move to [Control
Panel>System>Device Manager>Network adaptors].
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
GB
2
5. Check'SpecifyanIPaddress', andwrite'IPaddress'&'Subnetmask'thatyou
want to use. For example:
IP address:
192.168.1.3
Subnet mask:
255.255.255.0
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Access PC via Network
GB
2
If you have already been 'obtained an IP address automatically'
from DHCP Server or IP Router on your local area network, you
don't need to enter a specific IP address. Use 'Obtain an IP
address automatically' or write IP address & Subnet mask that
DHCP Server or IP Router provides.
6. Set the network configurations of the player
You have to connect the player to a TV set for this setup. See
"3.1.1 Connect Video Cable".
Press [SETUP] of remote control for moving to setup screen.. Select 'DHCP Off'
and write IP address & Subnet mask. For example:
IP Address:
192.168.1.2
Subnet mask:
255.255.255.0
After entering the numbers, press [SETUP] again for saving configurations.
If you have already been provided a dynamic IP address from
DHCP Server or IP Router on your local area network, you don't
need to enter a static IP address. Use 'DHCP on' or enter the IP
address & Subnet mask that DHCP Server or IP Router provides.
Check 'IP address obtained automatically' When you use 'DHCP
On', you can see the IP address in MENU screen after selecting
'PC-Network' icon in Mode Selection screen.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
GB
2
The MediaPlayer IP Address
2.2.2 Windows 2000
1. Select a folder which you want to share. Right-click the folder and click
'Sharing' in pop menu.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Access PC via Network
2. Check 'Share this folder' and write 'share name'. For example, "My Movie":
GB
2
"Share Name": maximum length is 12 characters.
3. Click 'Permissions' and check whether "Everyone" account is present or not.
If not, add "Everyone" account.
We Recommend only to use 'Read>Allow' at Permissions.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
4. After that, the shared folder will be displayed as following picture.
GB
2
5. Move to [Settings>Control Panel>Administrative Tools>Computer
management>Local Users and Groups>Users], and double click 'Guest'.
6. Check 'User cannot change password' and 'Password never expires'.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Access PC via Network
7. Move to [Control Panel>Network and Dial-up Connections], and select
Properties 'Local Area Connections' by right click of mouse.
GB
2
If you see two or more 'Local area connections', select one that
you will use for connecting to the player.
8. Double click 'Internet Protocol (TCP/IP)' that you want to use on your
computer.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
9. Check 'Use the following IP address', and write 'IP address' & 'Subnet mask'
that you want to use. For example:
GB
2
IP address:
192.168.1.3
Subnet mask:
255.255.255.0
If you have already been provided a dynamic IP address from
DHCP Server or IP Router on your local area network, you don't
need to enter a static IP address. Use 'Obtain an IP address
automatically' or enter the IP address & Subnet mask that DHCP
Server or IP Router provides.
10. Set the network configurations of the player.
You have to connect the player to a TV set for this setup. See
"3.1.1 Connect Video Cable".
Press [SETUP] on remote control for moving to setup screen. Select 'DHCP off'
and write IP address & Subnet mask. For example:
IP Address:
192.168.1.2
Subnet mask:
255.255.255.0
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Access PC via Network
After entering the numbers, press [SETUP] again to save the configuration.
GB
2
IfyouhavealreadybeenprovideddynamicIPaddressfromDHCP
Server or IP Router on your local area network, you don't need
to enter a static IP address. Use 'DHCP on' or write IP address &
Subnet mask that DHCP Server or IP Router provids.
Check 'IP address obtained automatically'
When you use 'DHCP On', you can see the IP address in MENU
screenafterselecting'PC-Network'iconinModeSelectionscreen.
The MediaPlayer IP Address
2.2.3 Windows XP
1. Select a folder which you want to share. Right-click the folder and click
'Sharing and Security' in pop menu.
2. Check 'Share this folder on the network' and write 'Share name'. For
example, "My Movie".
"Share Name": maximum length is 12 characters.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
GB
2
3. After that, the shared folder will be displayed as following picture.
4. Move to [Settings>Control Panel>Administrative Tools>Computer
management>Local Users and Groups>Users], and double click 'Guest'.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Access PC via Network
GB
2
This is for Windows XP Professional. Windows XP Home users
can't see this figure. Go to next number 6).
If you can't find 'Administrative Tools' at Control Panel, click
"Switch to classic view" in left-up corner on screen.
5. Check 'User cannot change password' and 'Password never expires'.
6. Move to [Control Panel>Network connections], and select 'Local area
connections' properties by right click of mouse.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
GB
2
If you can't find 'Administrative Tools' at Control Panel, click
"Switch to classic view" in left-up corner on screen.
If you see two or more 'Local area connections', select one that
you will use for connecting to the player.
7. Double click 'Internet Protocol(TCP/IP)' that you want to use on your
computer.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Access PC via Network
8. Check 'Use the following IP address', and write 'IP address' & 'Subnet mask'
that you want to use. For example:
GB
2
IP address:
192.168.1.3
Subnet mask:
255.255.255.0
IfyouhavealreadybeenprovideddynamicIPaddressfromDHCP
Server or IP Router on your local area network, you don't need
to enter a static IP address. Use 'Obtain an IP address automati-
cally on' or enter the IP address & Subnet mask that DHCP Server
or IP Router provides.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
9. At above number 7 figure, click 'Advanced' Tab. Disable 'Internet Connec-
tion Firewall'.
GB
2
If you use service pack 2, refer to the following figures. Click 'Settings' at
'Windows Firewall'
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Access PC via Network
Check 'Off' and click 'OK'
GB
2
10. Set the network configurations of the player.
You have to connect the player to a TV set for this setup. See
"3.1.1 Connect Video Cable".
Press [SETUP] on the remote control for moving to setup screen. Select
'DHCP off' and write IP address & Subnet mask.
For example:
IP Address:
192.168.1.2
Subnet mask:
255.255.255.0
After entering the numbers, press [SETUP] again to save the configurations.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
GB
2
•
If you have already been provided dynamic IP address from
DHCP Server or IP Router on your local area network, you
don't need to enter a static IP address . Use 'DHCP on' or enter
the IP address & Subnet mask that DHCP Server or IP Router
provides.
•
•
Check 'IP address obtained automatically'
When you use 'DHCP On', you can see the IP address in MENU
screen after selecting 'PC-Network' icon in Mode Selection
screen.
MediaPlayer IP Addres
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
Chapter 3: Use as Multimedia Player
GB
3
3.1 Connect to External AV Device
3.1.1 Connect Video Cable
The player supports 3 types of video output; "Composite, S-video and Compo-
nent". Use the video connection that your TV supports. Normally, TV supports
composite video connection; a composite video cable is supplied with the
player.
1. Composite: Yellow RCA cable. (Supplied)
Yellow
(CVBS)
Yellow
(CVBS)
Connect to Composite
(CVBS) Jack of TV
2. S-Video: Black rounded cable (not supplied)
S-VIDEO
Connect S-Video Jack
of TV
3. Component: Y, Pb, Pr component cable (not supplied)
Red
(Pr)
Red
(Pr)
Connect Pr Jack of TV
Blue
(Pb)
Blue
(Pb)
Connect Pb Jack of TV
Green
(Y)
Green
(Y)
Connect Y Jack of TV
When you do not see a normal screen after connecting the video
cable, check the following:
1. "TV "– Switch to Video Input Mode: Turn on TV, and switch to
video input mode same as video connection. See TV user
manual.
2. "player" – Switch to Video Output Mode: Press [VIDEO] button
repeatedly. Whenever press [VIDEO], video output signal is
changed.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
GB
3
3. After you see normal screen, you have to save video configu-
ration of the player. See "3.2.1 Video Setup".
3.1.2 Connect Audio Cable
The player supports 3 type of audio output; "Stereo, Coaxial and Optical". Use
audio connection that your TV or Audio set supports. Normally, TV supports
standard stereo audio connection, the cable for this is supplied with the player.
1. Stereo: Red & White RCA Cable (supplied)
Red
Red
Connect Stereo-R
Jack of TV.
(STEREO-R)
(STEREO-R)
(STEREO-L)
White
(STEREO-L)
White
Connect Stereo-L
Jack of TV.
2.Optical (¨): Optical Cable for Digital 5.1 ch. (not supplied)
Connect Optical Jack of
OPTICAL (ꢀ)
Amplifier or Receiver
3. Coaxial: Coaxial cable for Digital 5.1 ch. (not supplied)
Connect Coaxial jack of
COAXIAL
Amplifier or Receiver.
Don't connect optical and coaxial cable together at the same
time!
When you do not hear sound after connecting Optical or Coaxial
Cable, you have to change audio setup of the player as Encoded
Digital. See "3.2.2 Audio Setup"
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
3.2 Basic Setup
3.2.1 Video Setup
GB
3
This chapter shows you how to setup the video output of the player. You have
to setup the player's video output mode to correspond to the video input mode
of your TV.
When you do not see a normal screen after connecting video
cable, check the following:
1. "TV "– Switch to Video Input Mode: Turn on TV, and switch to
video input mode same as video connection. See TV user
manual.
2. "Player" – Switch to Video Output Mode: Press [VIDEO] button
repeatedly. Whenever [VIDEO] is pressed, the video output
signal is changed.
3. After you see normal screen, you have to save video configu-
rations of the player.
TTV Video
Input Mode
Player Video
Output Mode
Connection Jack
of TV, Player
Video Cable Type
Normal Video
TV Out: NTSC C/S-Video
(HD Component OFF)
CVBS or Composite
Jack
Yellow RCA Cable
(Supplied)
TV Out: PAL C/S-Video
(HD Component OFF)
(Generally Yellow
Jack)
S-Video
TV Out: NTSC C/S-Video
(HD Component OFF)
S-Video Jack
S-Video Cable
* Black rounded
TV Out: PAL C/S-Video
(HD Component OFF)
Component 480i
TV Out: NTSC C/YPbPr
(HD Component OFF)
Component 3 Jack
*Y(Green), Pb(Blue),
Pr(Red)
Component Cable
*Y(Green),Pb(Blue),
Pr(Red)
TV Out: PAL C/YPbPr
(HD Component OFF)
Component 480p
Component 720p
Component1080i
HD Component Out On
480p
HD Component Out On
720p
HD Component Out On
1080i
NTSC, PAL : Standard of TV Output. Select the corret one for use
in your country.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
Setup Procedure
GB
3
1. Turn on the player and press [SETUP] on Mode Selection screen.
2. Move to 'TV Out' icon and press [ENTER]. Setup box will be displayed under
icon menu.
3. Move to Video Output Mode that you want and press [ENTER].
4.Press [SETUP] again to save the configurations.
3.2.2 Audio Setup
This chapter shows you how to set up the audio output of the player. You can
use Stereo or Digital 5.1 ch.
Analogue/DCPM: Select when you connect the supplied audio
cables (Red / White) to TV or Audio set directly.
Encoded Digital: Select when you want to listen through 5.1Ch
/ DTS Dolby by connecting receiver (or amplifier) with Optical or
Coaxial cable.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
Setup Procedure
GB
3
1. Turn on the player and press [SETUP] in Mode Selection screen.
2. Move to 'Audio' icon and press [ENTER]. Setup box will be displayed under
icon menu.
3. Move to Audio Output Mode that you want and press [ENTER].
4. Press [SETUP] again to save the configurations.
3.2.3 Network Setup
You can obtain an IP address automatically from DHCP Server or IP Router, or
set the specific IP address. Check your network environments.
DHCP On: You can use this option when it is possible to obtain IP
address automatically from DHCP Server or IP Router.
DHCP Off: When it is not possible to obtain IP address automati-
cally or you connect to your PC directly without DHCP Server or
IP Router, you have to use this option. Just enter the IP address
and Subnet mask.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
DHCP On Setup Procedure
GB
3
1. Turn on the player and press [SETUP] in Mode Selection screen.
2. Move to 'Network' icon and press [ENTER]. Setup box will be displayed
under icon menu.
3. Move to DHCP On and press [ENTER].
4. Press [SETUP] again for saving configurations.
Check 'IP address obtained automatically'
When you use 'DHCP On', you can see the IP address in MENU
screenafterselecting'PC-NetworkiconinModeSelectionscreen.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
DHCP Off Setup Procedure
GB
3
1. Turn on the playerand and press [SETUP] in Mode Selection screen.
2. Move to 'Network' icon and press [ENTER]. Setup box will be displayed
under icon menu.
3. Move to DHCP Off and press [ENTER].
4. Move to 'IP Addr' and press [ENTER]
IP address Input box will be displayed. Enter IP address using arrow and
number buttons of remote control. After this, press [ENTER] again.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
5. Move to 'Subnet' and press [ENTER].
GB
3
Subnet mask Input box will be displayed. Enter Subnet mask using arrow
and number buttons of remote control. After this, press [ENTER] again.
6. Press [SETUP] again tor save configurations.
Check 'The specific IP address you wrote'
When you use 'DHCP off', you can see the IP address in MENU
screenafterselecting'PC-Network]iconinModeSelectionscreen.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
3.2.4 Screen Setup
GB
3
This chapter shows you how to set the TV Type. You can select 4:3 Letter Box,
4:3 Pan Scan, and 16:9.
Setup Procedure
1. Turn on the player and press [SETUP] in Mode Selection Screen.
2. Move to 'Screen' icon and press [ENTER]. Setup box will be displayed under
icon menu.
3. Moveto4:3Letterbox, 4:3Panscanor16:9thatyouwantandpress[ENTER].
4. Press[SETUP] again to save configurations.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
3.2.5 Preview Setup
GB
3
You can enable or disable preview the photo file as a thumbnail image before
playing.
Setup Procedure
1. Turn on the player and press [SETUP] in Mode Selection screen.
2. Move to 'LED' icon and press [ENTER]. Setup box will be displayed under
icon menu.
3. Move to LED on or off; select the setting you want and press [ENTER].
4. Press [SETUP] again to save the configurations.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
3.2.6 LED Setup
GB
3
You can turn on or off the backlight LED of the arrow buttons on the front side
of the player. For instance, should the LED disturb you at night, you can turn
off the LED.
Setup Procedure
1. Turn on the player and press [SETUP] in Mode Selection screen.
2. Move to 'LED' icon and press [ENTER]. Setup box will be displayed under
icon menu.
3. Move to LED on or off; select the setting you want and press [ENTER].
4. Press [SETUP] again to save the configurations.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
3.3 Basic Screen Menu
GB
3
3.3.1 Mode Selection, Media Type Selection
After turning on the player, you will see the Mode Selection screen. In this
screen, you can select Built-in HDD or Networking Computers. Just press
[ENTER] after moving to the desired icon with the arrow buttons.
If there is no HDD or networking PC, these icons are not acti-
vated.
Use Built-in HDD
1. [Mode Selection] Move to 'MediaPlayer-35' icon and press [ENTER] for
playing files from the built-in HDD.
2. [MediaTypeSelection]Selectamediatypewhichyouwanttoplayandpress
[ENTER].
•Video: Select for playing Video files
•Music: Select for playing Music files
•Photo: Select for playing Photo files
•List: Select for making a playlist including video, music, photo files
•Setup: Select for moving to setup screen.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
Use Networking Computer
GB
3
1. [Mode Selection] Move to 'PC-Network' icon and press [ENTER] for playing
files from computer(s) within your network.
2. [MediaTypeSelection]Selectamediatypewhichyouwanttoplayandpress
[ENTER].
•Video: Select for playing Video files
•Music: Select for playing Music files
•Photo: Select for playing Photo files
•List: Select for making a play list including video, music, photo files
•Setup: Select for moving to setup screen.
3. [Computer list on network] Computer list on network will be displayed.
Move to a computer and press [ENTER].
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
3.3.2 File Selection
GB
3
After selecting a Media type, 'File Selection' screen will be displayed. Move to
the file that you want to play and press [ENTER] or [PLAY/PAUSE].
Icon Menu Tray
•
•
[ENTER] button: Play one file that you select. After finishing playback,
return to 'file selection screen'.
[PLAY/PAUSE] button: After playing the file that you select, the next files
are automatically played.
•
•
•
button: Move to files by pressing
arrow buttons.
arrow button.
button: Return to previous directory by pressing
button: Go to 'Icon Menu Tray', located at the top of the screen, by
pressing button. In order to return to file selection screen, press arrow
button or select Exit icon.
Icon Menu Tray Descriptions
Go to 'Icon Menu Tray', located at the top of the screen with pressing button.
In order to return to file selection, press
arrow button or select 'Exit' icon.
Back: Return to previous directory
Allplay: After playing the file that you select, play all files automatic-
ally. This is the same function as [PLAY/PAUSE] button.
Menu: Return to Media Type screen.
Exit:
Exit Icon Menu Tray and return to file selection screen.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
3.4 Play Video Files
GB
3
You can play video files like AVI, MPG, MPEG, DAT, M2V, and VOB. Select
'Movie' icon in Media Type Selection screen. Video file list will be displayed.
Move to a file and press [ENTER] or [PLAY/PAUSE] button.
Select 'Movie' icon in Media Type Selection screen.
Move to a file and press [ENTER] or [PLAY/PAUSE] button.
Function and Button Descriptions
Remote Control
AUDIO
Function
Descriptions
Dual Audio
It is possible to switch each audio language when the
audio format is dual-audio, for example, including a
local language and English.
SUBTITLE
Subtitle
Move& Size
It is possible to change subtitle size and location.
arrow button changes size and
arrow button
changes location. After selecting, press [ENTER].
Subtitle
Select or Hide
The subtitle name, same as video file, is displayed on
screen automatically. However, it is possible to open
or hide the other available subtitle files.
Subtitle
LanguageSelect
It is possible to switch each subtitle language when
the subtitle is dual language format, for example,
including a local language and English.
* When selecting 'Discriminating subtitle language',
first subtitle language will be displayed.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
Subtitle
Sync.
It is possible to set the subtitle sync. with
(one
GB
3
second)
(60 second) when motion and subtitle
sync do not match.
4, 5, 6
Subtitle
Subtitle color is changed when pressing number 4, 6
button.
Inordertoreturndefaultcolor(white), pressnumber5.
Number Button
Color Change
Zoom Vertical
Zoom Full
Custom
Scr. SIZE
Zoom screen vertically.
Enlarge the overall screen.
Enlarge or reduce the screen by pressing
arrow buttons.
Default
Return to original screen size and position.
Screen Position
Move the screen to the direction with
arrow
buttons. Press [Brt.Cont] key for returning to the
original screen position when applying Screen posi-
tion.
TIME SEARCH
Jump to Prefer-
able Playback
Time
Move to a selected time of a file.
CANCEL
Delete Input
Numbers
In time search box, this button deletes all numbers to 0.
Brt. CONT
Control luminos-
ity, color depth,
brightness
Whenpressingthisbutton, youcanswitchto3modes.
After selecting a mode, change settings with
arrow buttons.
FILE INFO
Show File Infor-
mation
Show the file information which is being played. To
hide this information, press this button again.
FF
Fast Forward
When this button is pressed, play speed is changed to
8x, 16x, 32x ( forward).
arrow button
REW
arrow button
Rewind
When this button is pressed, play speed is changed to
8x, 16x, 32x (backward).
VOLUME +
Volume Up
Volume Down
Sound Off
Volume up.
arrow button
VOLUME -
arrow button
Volume down.
MUTE
Mute the sound. To hear sound, press this button
again.
ENTER
Playback a File
Play a file. After finishing playback, return to file
selections screen.
PLAY / PAUSE
II
Playback
Next All Files
After the file that you select, play the next files
automatically. This function is the same as [PLAY/
PAUSE] button.
PLAY / PAUSE
II
Pause
Pause playback, if pressing this button when a file is
being played. To play again, press this button again.
PREV
I
Playback
Previous File
Play a previous file before a current playback file. If
you used [ENTER] for playback, you can not use this
function. This function is available when playing all
files using [PLAY/PAUSE] button or 'ALLPLAY' icon.
NEXT
I
Playback
Next File
Play a next file after a current playback file. If you
used [ENTER] for playback, you can not use this
function. This function is available when playing all
files using [PLAY/PAUSE] button or 'ALLPLAY' icon.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
0
Screen Reset
If a frame of a video file is broken, green color will be
shown on the overall screen. Press number [0 "Zero"]
for screen reset.
GB
3
Number button
MENU
Menu Icon
Popup
Popup menu will be appear including 'File Info, Time
Search,Subtitle,Scr.Size'functions.Tohidethepopup,
press this button again.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
3.5 Play DVD Files
GB
8
The DVD manager function supports playing ripped DVD Files in same way as
an original DVD. Make a separate folder for each ripped DVD, then save all
ripped files into the folder. After connecting TV, select VIDEO_TS.IFO file in the
folder. Make sure that all the ripped files include the VIDEO_TS.IFO file.
If you can not find VIDEO_TS.IFO file among all the ripped files
from an original DVD title, the DVD manager function will not
work.
When you play DVD file in networking computer, playback time
mightbedelayed, soit'snotpossibleinallcasestoplayDVDfiles
on networks. We recommend to use this feature in combination
with a built-in HDD, and play your ripped DVD files from this
built-in HDD.
Select 'Movie' icon in Media Type Selection screen.
MovetothefolderincludingDVDrippedfiles, select'video_ts.ifo'fileandpress
[ENTER] button.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
Function and Button Descriptions
GB
8
Remote Control
AUDIO
Function
Descriptions
Select Audio
Type
Audio type will be changed when this button is
pressed.
SUBTITLE
Scr. SIZE
Select Subtitle
Type
Subtitle type will be changed when this button is
pressed.
Screen Size
Screen size will be changed when this button is
pressed.
MENU
SLOW
Go to Menu
Move to main menu while playing DVD.
Playback Slow
Play slowly 1/2x, 1/4x, and 1/8x whenever this button
is pressed.
REPEAT
Chapter, Title
Repeat
Set chapter, title repeat.
A-B REPEAT
TITLE
A-B repeat
Set A-B repeat.
Go to Title
Menu
Move to title menu while playing DVD.
ANGLE
Angle
Apply angle function.
FILE INFO
Show File Infor-
mation
Show the file information of the file currently being
played. To hide the information, press this button
again.
TIME SEARCH
Jump to Prefer-
able Playback
Time
Move to a selected time of a file.
CANCEL
Delete Input
Numbers
In time search box, this button deletes all numbers
to 0.
Brt. CONT
Control luminos-
ity, color depth,
brightness
When this button is pressed, you can switch to 3
modes After selecting a mode, change settings with
arrow buttons.
PREV
I
Playback
Previous Chap-
ter
Play a previous chapter.
NEXT
I
Playback
Next Chapter
Play a next chapter.
FF
Fast Forward
When this button is pressed, play speed is changed to
8x, 16x, 32x, 48x (forward).
REW
ENTER
Rewind
Whenthisibuttonispressed, playspeedischangedto
8x, 16x, 32x, 48x (backwards).
Playback
Pause
Play 'Video_ts.ifo' file.
PLAY / PAUSE
II
Pause playback, when pressing this button when a
file is being played. To resume playback, press this
button again.
VOLUME +
VOLUME -
MUTE
Volume Up
Volume Down
Sound Off
Volume up.
Volume down.
Mute the sound. To hear sound, press this button
again.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
3.6 Play Music Files
GB
3
You can play music files like MP3, OGG, WAV, WMA. Select Music icon in Media
Type Selection screen. The Music file list will be displayed. Just move to a file
and press [ENTER] or [PLAY/PAUSE] button.
Select Music icon in Media Type Selection screen.
Move to a file and press [ENTER] or [PLAY/PAUSE] button.
Function and Button Descriptions
Remote Control
FILE INFO
Function
Descriptions
Show File Infor-
mation
Show the file information of the file that is currently
being played. To hide the information, press this
button again.
TIME SEARCH
Jump to Prefer-
able Playback
Time
Move to a selected time of a file.
CANCEL
Delete Input
Numbers
In time search box, this button deletes all numbers
to 0.
Brt. CONT
Control luminos-
ity, color depth,
brightness
Whenpressingthisbutton, youcanswitchto3modes.
After selecting a mode, change settings with
arrow buttons.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
PREV
I
Playback
Play a previous file before a current playback file. If
you used [ENTER] for playback, you can not use this
function. This is available only when playing all files
as using [PLAY/PAUSE] button or 'ALLPLAY' icon.
GB
3
Previous File
NEXT
I
Playback
Next File
Play a next file after a current playback file. If you
used [ENTER] for playback, you can not use this
function. This is available only when playing all files
as using [PLAY/PAUSE] button or 'ALLPLAY' icon.
FF
Go to 10 Sec. in
Forward
Go to 10 sec. forward and play when a file is being
played.
REW
ENTER
Go to 10 Sec. in
Backward
Go to 10 sec. backward and play when a file is being
played.
Playback a File
Play a file. After finishing playback, return to file
selections screen.
PLAY / PAUSE
II
Playback
Next All Files
After the file that you select, play next l files auto-
matically. Function is the same as [PLAY/PAUSE] but-
ton.
PLAY / PAUSE
II
Pause
Pauseplayback, whenpressingthisbuttonduringfile
playback.Toresumeplayback,pressthisbuttonagain.
VOLUME +
VOLUME -
MUTE
Volume Up
Volume Down
Sound Off
Volume up.
Volume down.
Mute the sound. In order to hear sound, press this
button again.
SUBTITLE
Hide MP3 Sub-
title
You can show the MP3 subtitle (when the MP3 file
supports this feature). In that case, this button will
hide the subtitle.
MP3 subtitle supported file must be made by iriver
caption editior program. It does not support LDB
program.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
How to Play MP3 without TV set. MP3 Quick Play
GB
3
Make a 'music' folder (in a small letter not a capital letter) at root directory of
built-in HDD and save MP3 files at the folder. If the HDD is divided into two or
more partitions, make a 'music' folder at first partition.
Turn on the player and just press [PLAY/PAUSE] button. MP3 files at 'music'
folder will be played automatically. Additionally, after rebooting the player,
the last played file will be continue to play.
How to See MP3 Subtitle
It is possible to show MP3 subtitle (when the MP3 file supports this feature).
MP3 subtitle supported file must be made by 'iriver caption editior' program,
it does not support the LDB program.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
Use as Multimedia Player
3.7 Play Photo Files
GB
3
You can play photo files like JPG(JPEG). Select the Photo icon in Media Type
Selection screen. Photo file list will be displayed. Just move to a file and press
[ENTER] or [PLAY/PAUSE] button.
Select the Photo icon in Media Type Selection screen.
Move to a file and press [ENTER] or [PLAY/PAUSE] button.
Function and Button Descriptions
Remote Control
FILE INFO
Function
Descriptions
Show File Infor-
mation
Show the file information of the file that is being
played. To hide the information, press this button
again.
PREV
I
Playback
Previous File
Play a previous file before the current playback file.
If you used [ENTER] for playback, you can not use this
function. This is available only when playing all files
as using [PLAY/PAUSE] button or 'ALLPLAY' icon.
NEXT
I
Playback
Next File
Play a next file after the current playback file. If you
used [ENTER] for playback, you can not use this
function. This is available only when playing all files
as using [PLAY/PAUSE] button or 'ALLPLAY' icon.
ENTER
Playback a File
Play a file. After finishing playback, return to file
selections screen.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
PLAY / PAUSE
II
Playback
After the file that you select, play all next files
automatically. Itisthesamefunctionas[PLAY/PAUSE]
button.
GB
3
Next All Files
PLAY / PAUSE
II
Pause
Pause playback, when this button is pressed during
file playback To play again, press this button again.
FF
Zoom In
Zoom Out
Enlarge a photo.
REW
ANGLE
Reduce a photo.
Rotation
Panning
Rotate a photo.
Move the position of photo.
Return to original photo.
ENTER
Return to Origi-
nal Photo
Brt. CONT
Controlluminos-
ity, color depth,
brightness
Whenpressingthisbutton, youcanswtichto3modes.
After selecting a mode, change settings with
arrow buttons.
Photo Slide Show
If you play all files with 'PLAYALL' icon or [PLAY/PAUSE], photo slide show will
be started.
Music Slide Show
Make a 'music' folder (in a small letter not a capital letter at root directory) of
built-in HDD and save MP3 files in this folder. If the HDD is divided into two or
more partitions, make a 'music' folder in the first partition.
When you play one or all photo files, you can listen to MP3 and see photo slide
show together.
However, if there is just networking computer (not built-in HDD), you cannot
listen MP3. In this function the player only detects MP3 files of the built-in
HDD's music folder.
Photo Preview On, Off
Itispossibletoenableordisablepreviewofthephotofileasathumbnailimage
before playing, in the SETUP screen.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
3.8 Make a Play-List
GB
3
Your can create a playlist of all media files like video, music, and photo.
It is not possible to play every registered file independently. Use
'Random, PLAY all' icon or [PLAY/PAUSE] button. Also, the regis-
tered play-list will be deleted after rebooting.
1. Select Play List icon in Media Type Selection screen.
2. Move to a file and press [ENTER] for adding to Play-List. After adding, press
[ ] for moving to 'Menu Icon tray'. Move to 'List' icon and press [ENTER].
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
3. Play-List screen appears. You can see just added files. Play as follows:
•Random icon: play random.
GB
3
•Allplay icon: play in order of selected file.
•Play/Pause button: play in order of selected file.
•
•
•
In order to move up to Menu Icon Tray, press [ ] button.
By selecting the delete (X) icon will all the added files.
In order to delete an added file, move to the file on Play-List screen and
press [ENTER] twice.
•
In order to change location among added files, move to the file you want
to move, press [ENTER] , move to the file where you want to add it below,
and press [ENTER].
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Use as Multimedia Player
3.9 Remote Control
GB
3
This chapter shows the basic use of the remote control. For more details, '3.3
Basic Screen Menu', '3.4 Play Video Files', '3.5 Play DVD Files', '3.6 Play Music
Files', '3.7 Play Photo Files', '3.8 Make a Play-List'.
POWER: Turn On / Off SETUP Go to Setup Screen.
MENU: Go to DVD Main Menu, Display Menu Icon When Playing Video File.
TITLE: Go to DVD Title Menu ANGLE DVD Angle, Photo Rotation
REPEAT: Set DVD Chapter, Title Repeat A-B REPEAT Set DVD A-B Repeat.
SLOW: Play DVD Slowly.
ENTER: Play a File
: Arrow Key . ( Return to Up
Directory)
FILE INFO: Show File Info.
TIME SEARCH: Jump to Specific play time
Brt.CONT: Set Luminosity, Color Depth,
Brightness
MEDIA TYPE: Go to Media Type Selection
Screen
MAIN PAGE: Go to Mode Selection Screen.
PLAY/PAUSE: Play next all files
Pause
STOP: Stop Play
REW: Play Faster in Backward.
FF: Play Faster in Forward.
PREV: Go to Previous Page,
VIDEO: Change Video Output Mode
Play Previous File in Play All
SUBTITLE: Subtitle Settings
NEXT: Go to Next Page
Scr. SIZE: Screen Size Settings
Play Next File in Play All
How to Insert/Change Battery
1. Pull out the battery tray of remote controller's body completely.
2. Put the enclosed battery on the tray.
3. Insert the tray into remote controller's body completely.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Freecom MediaPlayer Drive-In
3.10 Others
GB
3
3.10.1 Music Slide Show
Make a 'music' folder (in a small letter not a capital letter) in the root directory
of built-in HDD and save MP3 files in this folder. If the HDD is divided into two
or more partitions, make a 'music' folder at first partition. When you play one
or all photo files, you can listen to mp3 and see photo slide show together.
However, if you use the device with a networking computer (not built-in HDD),
you cannot listen to MP3. In this function, the player only detects MP3 files at
built-in HDD's music folder.
3.10.2 MP3 Quick Play
This is for listening to MP3 files without the use of a TV set. Make a 'music'
folder (in a small letter not a capital letter) in the root directory of built-in HDD
and save MP3 files in this folder. If the HDD is divided into two or more
partitions, make a 'music' folder in the first partition. Turn on the player and
just press [PLAY/PAUSE] button. The MP3 files at 'music' folder will be played
automatically. Additionally, after rebooting the Network MediaPlayer-35
drive in kit, the last played file will continue to play.
However, if you use the device with a networking computer (not built-in HDD),
you cannot listen to MP3. In this function, the player only detects MP3 files at
built-in HDD's music folder.
3.10.3 Change Background Image
It is possible to change a background image on the player. Select a picture file
and save it as 'mybg.jpg' in the root directory of built-in HDD. Background
image will be changed as 'mybg.jpg'.
We Recommend to use 720x480 pixels image.
3.10.4 Firmware Upgrade
The firmware of this device can be upgraded. You can find the latest firmware
firmware file in a specially created folder, for instance "Firmware". After
connecting the device to a TV set, move to the upgrade file and press [ENTER].
Upgrade is progressed automatically.
After finishing upgrade, you can check firmware version on Setup screen. Press
[SETUP] button. Do not turn off the power during firmware upgrade !!!
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Technical Specifications
GB
Product Name
Freecom Network MediaPlayer-35 Drive-In kit
Power
5V 1.5A /12V 1.5A
450g (without HDD)
57 x 150 x 185 mm
Weight
Dimension
Available OS
Windows 98/SE/ME/2000/XP, Mac OS X 10.1 or
higher,
Linux 2.4 or higher
USB Interface
Network Interface
HDD Type
480Mbps USB 2.0 (USB 1.1 Compatible) / Slave
10/100 Mbps LAN (RJ-45)
3.5"IDE HDD
HDD File System
TV Type
NTFS / FAT32
PAL / NTSC
Supported Format
Movie
MPEG 1, 2, 4 (MPG, MPEG, AVI, M2V,
DAT, VOB, IFO etc.)
DivX, XviD (except GMC, Qpel option
applied)
Music
Photo
MP3, OGG Vorbis, WAV, WMA (except
WMA9 pro.lossless)
JPG(JPEG)
Video Output
Audio Output
COMPOSITE
S-VIDEO
COMPONENT Y, Pb, Pr (480p, 720p, 1080i Progressive
Scan)
STEREO L-R
DIGITALCOAXIAL,OPTICAL(DTSPass-ThroughOnly)
Operating Temperature 0°C ~ 60°C
77
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY (valid in Europe/Turkey only):
We thank you for purchasing this Freecom product and hope you will enjoy using it.
In order to avoid unnecessary inconvenience on your part, we suggest reading the quick install guide,
instruction manual and any additional electronic and or printed manuals. When problems occur we
have a database with Frequently Asked Questions (FAQ) on our Freecom website (www.freecom.com),
please check this site before you contact the helpdesk.
Your Guarantee
All Freecom products come with unlimited technical phone and web support. By this Guarantee, Freecom
warrants their products to be free from defects in material and workmanship for a period listed below
from the date of its original purchase. If during this period of guarantee the product proves defective
due to improper materials or workmanship, Freecom will, without charge for labour or parts, at its
sole discretion, repair or replace the product or its defective parts upon the terms and conditions set
out below.
Conditions
This guarantee will be granted only when the original invoice or sales receipt (indicating the date of
purchase, product and serial number) is presented together with the defective product and a Freecom
RMA number received from the Freecom Website or given by a Freecom Service Center. Freecom
reserves the right to refuse the free-of-charge guarantee services when the date of purchase of the
product cannot be proven. This guarantee will not apply if the RMA number is missing, the serial
number on the product has been altered, removed or made illegible.
This guarantee covers only the hardware components packaged with the product. This guarantee
covers none of the following: (a) any consumable supplied with the product, such as media or batter-
ies; (b) damage to or loss of any software programs, data or removable storage media; (c) any damage
resulting from adaptations, changes or adjustments, which may have been made to the product,
without the prior written consent of Freecom; (d) attempted repair by any party other than autho-
rized by Freecom and (e) accidents, lightning, water, fire or any other such cause beyond the reason-
able control of Freecom.
With respect to all services provided, Freecom is not responsible for any damage to or loss of any
programs, data or other information stored on any media or any part of any product serviced. Freecom
is not liable for the consequence of business loss in case of system failure. Be sure to exclude all parts
not covered by this guarantee prior to returning the product to Freecom. Freecom is not liable for any
loss or damage to these items. If during the repair of the product the contents of the hard drive are
altered, deleted or in any way modified, Freecom is not liable whatsoever.
Repair parts and replacement products will be provided on an exchange basis and will be either new,
equivalent to new or reconditioned. All replaced parts and products become the property of Freecom
The period of guarantee for any product or part repaired or replaced in warranty shall be the balance
of the original guarantee. Repairs or replacements on product or parts out of warranty carry 6 (six)
months guarantee.
All Freecom products come with unlimited free technical phone and web support.
Freecom Product
Traveller & Portable
Classic & Internal Series
FC, FS & FX Series
FHD Series & FireWire Harddrive
MediaPlayer-XXX
DVB-T USB Stick
USB Floppy Disk Drive
USBCard (Pro)
Warranty period
1 year (Two years in Europe)
1 year (Two years in Europe)
1 year (Two years in Europe)
1 year (Two years in Europe)
1 year (Two years in Europe)
1 year (Two years in Europe)
1 year (Two years in Europe)
1 year (Two years in Europe)
1 year (Two years in Europe)
3 years
USB 2.0 CardReader
DAT & LTO Drives (retail)
DAT-S Kits
2 years
ThinServer*
Beatman
Cables
1 year (Two years in Europe)
1 year (Two years in Europe)
1 year (Two years in Europe)
* Controller inside 3 years after online registration only.
(GB)
Download from Www.Somanuals.com. All Manuals Search And Download.
|