Fisher Price Baby Monitor 71597 User Manual

TM  
Soothing Dreams  
Monitor  
with Remote Control  
Model Number: 71597  
For proper set-up and use, please read these instructions.  
Please keep this instruction sheet for future reference,  
as it contains important information.  
Transmitter is electrically powered.  
Remote control receiver is powered by the AC adaptor (included, plugs  
into standard household outlets 120V AC). Remote control receiver  
also runs on battery power (9V alkaline battery - not included).  
Requires one PR12 light bulb (included).  
An adult must install the battery (if used) and replace the light bulb.  
Tool needed for battery installation and  
light bulb replacement: Phillips screwdriver.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT!  
CAUTION  
This product cannot replace  
responsible adult supervision.  
• This product is not intended to be used as a medical monitor  
and its use should not replace adult supervision.  
• Test sound reception of remote control receiver before first-time  
use and whenever you change location of transmitter.  
• To prevent entanglement:  
- Never place transmitter in a crib or playpen. Keep transmitter  
and remote control receiver out of baby’s reach.  
- Never use extension cords with the AC adaptor.  
• Never use transmitter or remote control receiver near water  
(ie.: bathtub, sink, laundry tub or wet basement, etc.).  
• Always use transmitter and remote control receiver where there is  
adequate ventilation. To prevent overheating, keep transmitter and  
remote control receiver away from heat sources such as radiators,  
heat registers, direct sunlight, stoves, amplifiers, or other appliances  
which produce heat.  
• Never attempt to modify this product.  
Consumer Information  
Occasionally a consumer may experience a problem with one of our  
products. If this should happen, please call us toll-free, rather than  
return this product to the store. Usually, we can solve the problem  
over the telephone or send you replacement parts.  
Please call Fisher-Price® Consumer Relations, toll-free at  
1-800-432-KIDS, between 8 AM - 6 PM EST, Monday through Friday.  
Hearing-impaired consumers using TTY/TDD equipment,  
please call 1-800-382-7470.  
Or write to:  
Fisher-Price® Consumer Relations  
636 Girard Avenue  
East Aurora, New York 14052  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Receiver  
Battery Installation (Optional)  
9V (6LR61)  
SHOWN ACTUAL SIZE  
Batter
Compartmen
• Locate battery compartment dooon back of remote control receiver.  
• Loosen screw in battery compartment door with a Phillips screwdriver.  
Lift to remove battery compartment door.  
• Snap terminals of a fresh, 9V alkaline battery into remote control  
receiver connectors.  
• Replace battery compartment door and tighten screw.  
Do not over-tighten.  
Battery Tips  
• Remove the battery during long periods of non-use. Always  
remove an exhausted battery from the product. Battery leakage  
and corrosion can damage this product. Dispose of battery safely.  
• Do not dispose of the battery in a fire. The battery may explode  
or leak.  
• Never short circuit the battery terminals.  
• A non-rechargeable battery is not to be recharged.  
• Only a battery of the same or equivalent type as recommended in  
the “Battery Installation” instructions is to be used.  
• If a removable rechargeable battery is used, it is only to be charged  
under adult supervision.  
• A rechargeable battery is to be removed from the product before  
it is charged.  
• If you use a battery charger, it should be examined regularly for  
damage to the cord, plug, enclosure and other parts. Do not use  
a damaged battery charger until it has been properly repaired.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Testing Sound Reception  
Test transmitter transmission and  
remote control receiver reception.  
Power/Volume Dial  
Power/Volume  
Dial  
Power  
Indicator  
Place remote control receiver in  
room in which you intend to use it.  
Rotate power/volume dial to turn  
power on. Adjust remote control  
receiver location.  
Place transmitter in room in which  
you intend to use it. Rotate transmit-  
ter power/volume dial to turn power  
on. Turn on a radio.  
• Variable light display lights when  
sound is received by remote  
control receiver:  
Adjust  
Channel  
- One or two dots light for  
shallow sounds.  
- Three or more dots light for  
louder sounds.  
• If you experience interference  
(buzzing or static, etc.) while using  
one channel setting, switch both  
units to other channel. Selecting  
a channel is usually a one time  
adjustment.  
Hint: All four dots in remote control receiver variable light display light:  
- If you turn remote control receiver power on before transmitter power. You will  
also hear static noise. Turn volume down and turn transmitter power on.  
- If the remote control receiver is too far away from the transmitter. Move the remote  
control receiver closer to the transmitter.  
- If loud sounds are transmitting.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup & Use  
8
2
3
1
7
1
4
6
5
Back View  
Transmitter  
Transmitter  
Remote Control  
Receiver  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup & Use  
IMPORTANT! Test sound reception of this monitor before first time  
use and whenever you change location of transmitter (see page 5).  
Set transmitter channel switch to same channel as remote  
control receiver.  
1
Place transmitter in same room with child. Point microphone  
directly toward crib or play area.  
Unwrap and fully extend power cord for best transmission.  
Insert power cord plug into wall outlet.  
Rotate transmitter power/volume dial to turn power on.  
Power indicator lights.  
Choose a soothing mode:  
2
3
4
5
Light only  
Light and Music  
Light and Nighttime Nature Sounds  
SFX  
Choose a light mode:  
6
Ceiling Light Show  
Night Light  
7
8
If you chose Ceiling Light Show (  
on the back of transmitter so that it projects on ceiling  
over baby’s crib.  
), adjust projector  
Press soothing button on transmitter to activate your  
selection. Rotate power/volume dial to adjust volume.  
Light/music/nature sounds will turn on for about five  
minutes and then automatically turn off. If you’d like to  
immediately turn off light/music/nature sounds, press  
soothing button on transmitter again.  
Hint: If you do not want light/music/nature sounds on after presetting  
transmitter, do not press soothing button on transmitter.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup & Use  
9
11  
10  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup & Use  
Place remote control receiver where you will see or hear it.  
9
10  
Unwrap and fully extend AC adaptor cord for best reception.  
Insert AC adaptor jack into remote control receiver socket and  
plug into wall outlet.  
Note: To use a 9V alkaline battery for power source, refer to  
“Remote Control Receiver Battery Installation” instructions  
on page 4.  
Rotate remote control receiver power/volume dial to turn  
power on. Power indicator lights. Rotate power/volume dial  
to adjust volume.  
11  
Note: AC adaptor is 120 VAC, 60Hz, 3W input; 6 VDC 100mA output;  
center positive polarity; plug OD is 5.5 mm, plug ID is 1.5 mm.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup & Use  
Ceiling Light  
Show  
Night Light  
with Music or  
Nature Sounds  
Ceiling Light  
Show with Music  
or Nature Sounds  
Night Light  
• To soothe baby, press and hold soothing button (Soothe) on remote  
control receiver for about two seconds.Your baby enjoys what you  
have selected.  
• Light/music/nature sounds will turn off after approximately five minutes.  
To turn back on, simply press and hold soothing button (Soothe) on  
remote control receiver for about two seconds.  
IMPORTANT! It takes a few seconds for the transmitter to receive a signal  
from the remote control receiver. Be sure to press and hold the soothing  
button on the remote control receiver for about two seconds.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup & Use  
“Wah, Wah,  
Wah…”  
“Mommy is  
coming…”  
“Mommy is  
coming…”  
• To talk to baby, press talk button (Talk) and speak into microphone  
on remote control receiver. Release talk button (Talk) after you have  
finished talking.  
Hint: If light/music/nature sounds are playing when you press talk button (Talk),  
you will temporarily turn them off. Light/music/nature sounds turn back on after  
you are finished pressing talk button (Talk).  
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
Replacing the Light Bulb (Glass Bulb)  
IMPORTANT! Should light bulb become non-functional, you are  
advised to remove and replace it. This should be carried out away  
from child’s sleep or play area.  
Light Bulb  
Compartment Door  
C
1
3
B
A
Reflector  
Lens  
• Loosen screws in light bulb  
compartment door with a  
Phillips screwdriver.  
• Lift to remove light bulb  
compartment door.  
• While pressing lens of reflector  
, lift it from light bulb  
compartment cover.  
B
A
• Remove and properly discard  
C
light bulb  
.
• Replace light bulb with a  
new PR12 or equivalent  
light bulb.  
Hint: You may need to fit a flat  
edged object to pry light bulb  
compartment door up.  
Note: When replacing light  
bulb, be sure to discard light  
bulb properly. Beware of  
cracked or broken glass.  
Retainer  
2
• Turn light bulb compartment  
door so that inside faces up.  
• Loosen and remove two  
screws in the retainer with  
a Phillips screwdriver.  
• Remove retainer.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notch  
Light Bulb  
Compartment Door  
4
6
Tab  
Groove  
• At an angle, fit reflector over  
new light bulb.  
• Align notch in reflector with  
tab in light bulb receptacle.  
• Fit light bulb compartment  
door into back of transmitter.  
Press light bulb compartment  
door to “snap” into place.  
• Tighten screws in light bulb  
compartment door with  
Phillips screwdriver. Do not  
over-tighten.  
• Push reflector lens slightly  
and fit reflector edges  
into grooves in light bulb  
compartment cover.  
5
• Replace retainer and insert  
two screws.  
• Tighten screws with a Phillips  
screwdriver. Do not over-tighten.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problems & Solutions  
Circuit Breaker  
5
“Ma, ma, ma.  
Da, da, da…”  
3
4
“That doesn’t  
sound right. Maybe  
we should check the  
transmitter.”  
6
BUZZZZ  
2
1
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problems & Solutions  
PROBLEMS  
SOLUTIONS  
Transmitter power indicator  
not lit.  
Turn transmitter power on.  
Power indicator lights.  
1
2
1
You hear static or buzzing from  
remote control receiver.  
Make sure channel switches on  
both transmitter and remote  
control receiver are set to  
same channel.  
2
Transmitter power indicator  
not lit.  
Make sure light switch that  
controls power flow to wall  
outlet is on.  
3
3
Transmitter power indicator  
not lit.  
Check transmitter power cord  
plug-to-outlet connection.  
4
5
4
5
Transmitter power indicator  
not lit.  
Power is off because circuit breaker  
for baby’s room is off. Make sure  
house fuses and circuit breakers  
are on.  
You hear static or buzzing  
and all four dots lit on remote  
control receiver.  
Check all five solutions above.  
Any one or more of these solutions  
should solve the problem.  
6
6
Hint: If, after checking all of these solutions, you believe that your transmitter power  
cord or AC adaptor is is damaged, please call Fisher-Price® at 1-800-432-KIDS.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problems & Solutions  
“Thats gotta  
be coming from  
next door…”  
“Did you read  
about…”  
PROBLEM  
You can hear conversations or sounds from other homes.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
“Wah, Wah,  
Wah…”  
“That must  
be Susie  
next door”  
“I better get  
off the phone,  
shes up…”  
“Wah, Wah,  
Wah…”  
“Wah, Wah,  
Wah…”  
“Did you read  
about…”  
SOLUTION  
There is signal interference due to other nursery monitors on same  
channel or cordless telephone use. Change channel switches on  
both transmitter and remote control receiver to eliminate source  
of interference.  
Hints:  
- Do not use more than one transmitter and one receiver at same time  
in same household.  
- Always remember that you are using public airwaves when using  
your monitor. Conversations, even from rooms near transmitter, may  
broadcast to other nursery monitors, radios, cordless telephones, or  
scanners outside your home. To protect privacy of your home, always  
turn transmitter off when not in use.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problems & Solutions  
“Uh-oh, maybe I  
should move closer  
to the house.”  
TIC  
A
T
S
SOLUTION  
PROBLEM  
You hear static or buzzing because  
remote control receiver is out of  
range of transmitter.  
Move remote control receiver  
closer to transmitter.  
Note: Range varies depending  
on surrounding conditions such  
as noise levels, physical obstruc-  
tions and signal interference.  
Hint: If you cannot hear your child and all four dots do not light, your remote  
control receiver battery is weak. Replace remote control receiver battery with  
a fresh, 9V alkaline battery or use AC adaptor for power source.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care  
Excess dirt in transmitter and remote control receiver microphone will hamper  
transmission of sound. Clean outer surface of transmitter and remote control  
receiver with a cloth lightly dampened with a mild cleaning solution. Never  
immerse transmitter, remote control receiver or AC adaptor.  
FCC Note (United States Only)  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to part 15 of the FCC rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
- Consult the dealer or an experienced radio/TV technician for help.  
CAUTION: Changes or modifications not expressly approved by the manufac-  
turer responsible for compliance could void the user’s authority to operate  
the equipment.  
Soothing Dreams™ with Remote Control Monitor  
Model Number: 71597  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions: (1) This device may not cause harmful interference and  
(2) this device must accept any interference received, including interference that  
may cause undesired operation.  
Soothing Dreams™ with Remote Control Monitor  
Consumer Affairs Department  
636 Girard Avenue  
East Aurora, New York 14052  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
One (1) Year Limited Warranty  
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York 14052 warrants that  
the Soothing Dreams™ Monitor with Remote Control is free from all defects in  
material and workmanship when used under normal conditions for a period of  
one (1) year from the date of purchase. Should the product fail to perform prop-  
erly, we will repair or replace it at our option, free of charge. Purchaser is respon-  
sible for shipping the product to Consumer Relations at the address indicated  
above and for all associated freight and insurance cost. Fisher-Price, Inc., will bear  
the cost of shipping the repaired or replaced item to you. This warranty is void if  
the owner repairs or modifies the product. This warranty excludes any liability  
other than that expressly stated above including but not limited to any inciden-  
tal or consequential damages.  
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL  
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY  
NOT APPLY TO YOU.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE  
OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.  
If you have any questions about this product:  
In Canada, call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont Blvd.,  
Mississauga, Ontario L5R 3W2.  
In Great Britain, telephone 01628 500303.  
In Australia, Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,  
Richmond, Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812  
(valid only in Australia).  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.  
©2001 Mattel, Inc. All Rights Reserved.  
® and ™ designate U.S. trademarks of Mattel, Inc.  
Printed in China  
71597pr-0920  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Fellowes Paper Shredder DS 16Ci User Manual
First Alert Home Security System 2074EF User Manual
Fisher Price Baby Toy 73457 User Manual
Fisher Price Motorized Toy Car T7161 User Manual
Fisher Price Riding Toy T4262 User Manual
Franklin Industries LLC Refrigerator FBC36OD User Manual
Freestyle Watch 798 User Manual
Fujitsu Flat Panel Television PDS4213W H User Manual
Generac Portable Generator SD100 User Manual
Gigabyte Portable Speaker GP S5500 User Manual