™
Infant-to-Toddler Rocker
Toddler Seat
Infant Seat
Model Number: G5911
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
Please keep this instruction sheet, as it contains important information.
Use the upright position only when your child has developed enough upper body control to sit without leaning forward.
Always use the restraint until your child is able to climb in and out of the chair unassisted.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires one LR20 "D" alkaline battery (not included) for vibrations unit operation.
c
i
f
w
w
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before assembly, inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions
if needed. Never substitute parts.
#8 x 1.9 cm (3/4") Screw
Shown Actual Size
Cross
Brace
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
2
Side
Rails
• Insert a screw through the hole in the bottom of each side
rail and into the cross brace. Tighten the screws with a
Phillips screwdriver. Do not over-tighten.
Cross Brace
Button
Push
Seat Back Tube
Push
Side Rails
1
• Position each side rail so that the button faces outward.
• Fit the cross brace between the side rails, as shown.
• Push the cross brace down to “snap” it into place. This may
require a lot of force.
3
• Insert the seat back tube into the socket in each side rail.
• While pressing the tabs on the ends of the seat back tube,
continue to insert the seat back tube into the sockets in
each side rail, until the tabs “snap” into place. Make sure
you hear a “snap” on each side.
• Pull the seat back tube up to be sure it is secure in the
side rail sockets.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Side
Rail
Side Rail
Hole
Front Tube
Side
Rail
Front Tube
Vibrations
Unit
Side Rail
Hole
5
4
#8 x 3 cm (11/8") Screw
Shown Actual Size
(1
1/8")
• Locate the hole in each side rail.
• Insert a #8 x 3 cm
screw through the
outside of each side rail and
• With the vibrations unit facing forward, fit the front tube
to the side rails, as shown. Hold the front tube in place
and proceed to step 5.
into the ends of the front tube.
IMPORTANT! Please follow the next assembly (step 6)
carefully to completely secure the front tube to the
side rails.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Retainer
with Lock Nut
Kickstand
Press
Tab
Press
Tab
Rounded Side
6
Receptacles
7
M4 Lock Nut - 2
(Inside Retainer)
• Fit a retainer with lock nut
onto the end of the screw
and to the inside of a
side rail.
Shown Actual Size
• Position the assembly face down, as shown.
• While pressing the tab on each end of the kickstand,
insert the kickstand into the receptacle in each side rail,
as shown.
• Push the kickstand into the receptacles until the
tabs “snap” into place. Make sure you hear a “snap” on
each side.
Hint: A lock nut has been factory assembled to the retainer.
During shipment, the lock nut may have fallen out of the
retainer. If it has, please fit it into the hexagonal hole in the
retainer so that the rounded side of the lock nut faces out.
• Pull the kickstand to be sure it is secure in the receptacles.
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to fasten the screw in the other
end of the front tube and side rail, using the remaining
retainer with lock nut.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pad
Pad Slot
Press
Seat Back
Seat Back
Tube
Hardboard
8
9
Side
Rail
• Turn the assembly upright.
• Fit the upper pocket on
the pad onto the seat
back tube.
• Fasten the pad buckles
around each side rail.
• Turn the hardboard
over and insert it into
the slot in the front
Pad
Buckles
edge of the pad.
• Fasten the pad buckles on
the front edge of the pad
Pad
Buckles
and underneath the seat. Make sure you hear a “snap” on
both sides.
• Press the fasteners together in the seat back portion of
the pad.
Assembly is now complete.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Installation
Battery Safety Information
1.5V
LR20 "D"
+
–
SHOWN ACTUAL SIZE
Batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
Battery
Compartment
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose
of batteries safely. Do not dispose of batteries in a fire.
The batteries may explode or leak.
• Locate the battery compartment on the bottom of the
vibrations unit.
• Loosen the screw in the battery compartment door with a
Phillips screwdriver.
• Lift to remove the battery compartment door.
• Insert one LR20 "D" alkaline battery as indicated inside
the battery compartment.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
Hint: We recommend using an alkaline battery for longer
battery life.
• If removable, rechargeable batteries are used, they are only
to be charged under adult supervision.
• Replace the battery compartment door and tighten the
screw with a Phillips screwdriver. Do not over-tighten.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up & Use
Securing Your Infant
IMPORTANT! Before each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if
needed. Never substitute parts.
WARNING
To prevent serious injury or death:
• Always use the restraint until child
is able to climb in and out of the
chair unassisted.
• It is dangerous to use this product
on an elevated surface.
• Never leave child unattended.
WARNING
To prevent serious injury or death:
Use the upright position only when child
has developed enough upper body
control to sit without leaning forward.
Seat Position
Restraint
Restraint
Belt
Lower
Belt
Lift
Press
Button
Press
Button
Restraint
Pad
1
Recline
Upright
Select a seat position for your child’s comfort:
Upright or Recline.
2
Upright
While pressing the button on each side rail, lift the seat back.
• Place your child in the seat. Position the restraint pad
between your child’s legs.
Recline
While pressing the button on each side rail, lower the
seat back.
• Fasten the restraint belts to each side of the restraint pad.
Make sure you hear a “click” on both sides.
• Check to be sure the restraint system is securely attached
by pulling it away from your child. The restraint system
should remain attached.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing Your Infant
Toys
Anchored End
Anchored End
Strap
B
Strap
Strap
B
Toy
Free End
Toy
Free End
3
Loosen
Tighten
To tighten the belts:
• Feed the anchored end of the restraint belt up through the
buckle to form a loop
• Pull the free end of the restraint belt
• Repeat this procedure to tighten the other restraint belt.
To loosen the belts:
.
4
B
.
Toy
• Feed the free end of the restraint belt up through the
buckle to form a loop . Enlarge the loop by pulling on
the end of the loop toward the buckle.
• Fit the pad straps through
the slot in the toy rings.
Fasten the straps.
• Or, attach the toys to the
toy bar straps (please see
Step 5).
• Pull the anchored end of the restraint belt to shorten the
B
free end of the restraint belt
.
• Repeat this procedure to loosen the other restraint belt.
Hint: Pull the monkey’s head for a short tune.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Toy Bar
Calming Vibrations
Toy Bar
Plug
Plug
6
Toys
Power Switch
• Make sure your child is properly secured in the seat.
• Slide the power switch to the on position for
calming vibrations.
• Slide the power switch to the off position to turn
vibrations off.
5
• Fit the plugs on each end
of the toy bar into the
sockets in each side rail.
• Fit the toy bar straps
through the slot in the toy
rings. Fasten the straps.
• Or, attach the toys to the
pad straps (see Step 4).
Hint: Pull the monkey’s head for a short tune.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Kickstand
Storing the Restraint
System for Toddler Use
Small Slot
Small
Slot
Large
Slot
7
Kickstand
8
• Rotate the kickstand out.
• Push down on the seat bottom to be sure the kickstand
is in position.
• Insert the restraint belts back through the small slots in
the pad.
• Insert the restraint pad down through the large slot in
the pad.
9
• Turn the rocker face down.
• Tuck the ends of the restraint pad underneath the buckles,
as shown.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Care
The frame, pad toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach.
Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2004 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA
G5911pr-0726
Download from Www.Somanuals.com. All Manuals Search And Download.
|