Fisher Paykel Ventilation Hood 88833 EC120DXV2 User Manual

PRE-INSTALLATION  
Thank you for purchasing a quality, stainless steel canopy hood.  
We have a high standard of quality control and each canopy hood is tested and approved before it  
leaves the factory.  
Designer Series Island Canopy  
IMPORTANT  
Always switch the power off prior to installation, servicing or cleaning the canopy hood.  
Never use the canopy hood without the filters.  
Stainless steel is very easily damaged during installation if abraded or knocked by tools.  
Protect the top of the canopy with cardboard or polystyrene during installation.  
Please read the entire instructions before installing the canopy hood.  
80327 EC120DXV1 (SS NZ/AUS)  
80328 EC120DMV1 (IR NZ/AUS)  
88388 EC120DXV1 (EU)  
88833 EC120DXV2 (UK)  
A power outlet should be within 750mm from the motor assembly and can be either on the  
wall, behind the chimney or in the ceiling. An extension lead may be necessary on some  
installations.  
To comply to electrical safety regulations this canopy must be plugged into a socket near the  
appliance. The socket must be accessible and enable the end user to isolate the canopy from  
the power for the purpose of internal cleaning or maintenance.  
Ducting accessories are not supplied. All ducting must comply with local requirements and  
building codes.  
All electrical work must be done in accordance with local and/or national electrical  
codes as applicable. For safety this product must be earthed. If you are unfamiliar with  
methods of installing electrical wiring, employ the services of a qualified electrician.  
Turn off power at service entrance before installing wiring or servicing this product.  
The canopy hood is heavy please ensure adequate care when installing the canopy hood  
to prevent personal injury. The canopy hood must be installed onto a solid wall or solid  
lbs  
stud. Weight of product 43.2 kg.  
HEIGHT OF CANOPY HOOD  
The canopy is designed for 2440mm high ceilings.  
The chimney is telescopic and is designed for hood installations  
between 600 to 750mm above the cooking surface.  
Ascertain the desired installation height of the canopy hood.  
Any installation above 750mm will compromise the extraction  
performance.  
Please note product may vary slightly from the picture.  
Please read the entire instructions before installing the canopy.  
FILTER SURFACE  
HOB TOP  
INSTALLATION INSTRUCTIONS  
The air outlet from the motor requires 150mm round ducting  
which requires 170mm diameter hole in the ceiling.  
CONTENTS  
Contents of packaging  
1 x canopy hood  
Equipment required  
Electric drill  
Drill bits  
Spirit level  
Screwdriver  
Jig saw  
Ladder  
Tape measure  
Duct tape  
Optional accessories  
Light bulb  
Chimney ext.(10’) SS  
Chimney ext.(10’) IR  
Charcoal filter  
104467  
A=600 min (electric cook top)  
A=650 min (gas cook top)  
2 x chimney pieces  
8 x angle brackets  
1 x installation instructions  
4 x filters (part number 104660)  
Installation kit (part number 104922)  
4 x 12 x 40mm screw  
30 x 6 x ¼” self tapping screw  
(2 spare)  
103821  
1744  
Recirculation kit  
CONTROL PANEL  
Delay switch: Canopy hood will remain on a  
low, mid or high speed for five minutes to clear  
away all residual cooking odours before  
switching off automatically.  
I
I I  
I I I  
Ducting  
Fan On/Off  
Mid Speed  
High Speed  
Delay Switch  
Light On/Off  
104923 issue A  
ECN 06 037  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Eclipse Fujitsu Ten Laptop D2140 User Manual
Electro Voice Portable Speaker CM12 2 User Manual
Field Controls Air Cleaner UV E User Manual
First Alert Smoke Alarm SCO5B User Manual
Fisher Price Motorized Toy Car 74557 User Manual
Ford Remote Starter SK5W7J 19A361 AA User Manual
Gembird MP3 Player LECTEUR MOBILITY CLASSIC MP3 User Manual
Gemini Car Stereo System CD 100 User Manual
GE Refrigerator 21 23 25 27 29 User Manual
GE Telephone 29579 User Manual