User’s Guide
DVI-RGB 100
Direct Digital Video to RGB Video Converter
68-610-01 Rev. A
Printed in the USA
05 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Many monitors will not support all of the resolutions and refresh
rates shown. If you get no display, try a different rate.
c.
Install a blank panel (included in the rack kit) or another 1U
half-rack unit on the unused side of the rack.
3.
4.
Connect the input, loop-through and output cables. See Rear Panel
Connections and Controls.
SOG (Sync on Green) On/Off switch— Set this switch to the On
(up) position to enable SOG for RGsB video.
6
7
The maximum permissible length of the DVI input and output
cables is 16.4 feet (5 meters). Ensure that the cables do not exceed
the maximum permissible length, otherwise images may be
distorted or missing. Extron does not guarantee signal integrity
beyond 16.4 feet.
Set this switch to the Off (down) position to disable SOG for
RGBS or RGBHV video.
AC power connector — Plug a standard IEC power cord into this
connector to connect the converter to a 100 to 240VAC, 50 Hz or
60 Hz power source.
Configure the DDC, Output Resolution, and SOG switches. See
Rear Panel Connections and Controls.
Installation
5.
6.
7.
Connect power to the DVI-RGB 100.
1.
Power off the computer and its local monitor.
Power on the local monitor and other connected display device(s).
Power on the computer
2.
For optional rack mounting, mount the converter on a 19" 1U
Universal Rack Shelf (Extron part #60-190-01) (figure 3).
Front Panel Controls and Indicator
8
9
10
LEVEL
PEAK
BOOST
CONTROL
DVI-RGB 100
DVI TO RGB CONVERTER
Figure 4 — DVI-RGB 100 front panel
Power LED — The Power LED lights when the DVI-RGB 100 is
receiving power.
8
9
Level Boost control — The Level Boost control alters the bright-
ness of the picture on the RGB output. Judge the adjustment
visually by looking at the display.
False Front Panel
uses 2 front holes
•
At the minimum level setting (the counterclockwise limit of
this control), the converter outputs video at 0.5 volts p-p.
•
•
At the control’s midpoint, the converter outputs video at 0.7
volts p-p (unity level).
L
E
V
E
S
L
P
E
A
K
O
T
N
T
R
O
L
At the maximum level setting (the clockwise limit of this
control), the converter outputs video at 1.45 volts p-p.
(2) 4-40 x 3/16" Screws
D
V
R
D
I
-
V
I
T
R
G
G
B
O
B
N
C
1
0
O
0
R
V
E
R
T
E
Use 2 Mounting Holes on
Opposite Corners
Select a level setting of 0.7 volts and above to compensate for the
signal level decrease that occurs with long cables. Set the level at
the maximum setting for cable lengths over 500 feet.
Figure 3 — Rack mounting the DVI-RGB 100
Level Boost has no affect on the DVI output of the Buffered Loop-
through connector.
a.
Remove the rubber feet from the case if installed.
b.
Mount the converter on the rack shelf, using two 4-40 x 3/16
screws in opposite (diagonal) corners.
4
DVI-RGB 100 • Installation
DVI-RGB 100 • Installation and Operation
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicators and Specifications
Peak(ing) control — The Peaking control affects the sharpness of
the picture on the RGB output. Increased peaking can
10
Pin
1
Signal
Pin
9
Signal
Pin
17
Signal
compensate for detail (mid- and high-frequency) loss from low
bandwidth system components or capacitance in long cables. The
minimum setting (at the counterclockwise limit) provides no
peaking. The maximum setting (at the clockwise limit) provides
100% peaking. Adjust this control while viewing the displayed
image to obtain the optimum picture sharpness.
TMDS Data 2-
TMDS Data 2+
TMDS Data 1-
TMDS Data 1+
TMDS Data 0-
TMDS Data 0+
2
10
18
TMDS Data 2/4
Shield
TMDS Data 1/3
Shield
TMDS Data 0/5
Shield
3
11
19
4
5
TMDS Data 4-
TMDS Data 4+
12
13
TMDS Data 3-
TMDS Data 3+
20
21
TMDS Data 5-
TMDS Data 5+
Peaking has no affect on the DVI output of the Buffered Loop-
through connector.
Operation
TMDS Clock
Shield
6
DDC Clock
14
+5 V Power
22
After the DVI-RGB 100 and its connected devices are powered up, the
system is fully operational. If any problems are encountered, verify that
the cables are routed and connected properly.
7
8
DDC Data
15
16
Ground (+5 V)
Hot Plug Detect
23
24
TMDS Clock+
TMDS Clock-
No Connection
The computer reads the DDC on power up to determine the direct
digital video resolution and refresh rate to output. Ensure that
the local DVI monitor and the RGBHV monitor can both display
the selected resolution and refresh rate, otherwise images may be
distorted or missing.
• Use only the cable designed for DVI signals supplied by Extron.
• Limit or avoid the use of adapters.
• Use only approved DVI/DFP connectors.
Ensure that the computer and local DVI monitor are connected to
the DVI-RGB 100, and the DVI-RGB 100 and local monitor have
power applied, before applying power to the computer. If the other
devices are not turned on before the computer is, the image will
not appear.
Use only cables specifically intended for DVI or DFP
interfaces. Use of non-DVI or non-DFP cables or modified
cables can cause the DVI-RGB 100 to fail.
CAUTION
Specifications
DVI Connector Pin Assignments
Video
Figure 5 and the table below define the DVI pin assignments.
Bit rate (pixel bandwidth) .......... 1.6 gigabits/second/color
Pixel data bit depth ..................... 24 bit
Control data bit depth................. 6 bit
8
1
1
8
Maximum resolutions ................. 1280 x 1024 at 85 Hz, 1600 x 1200 at 60 Hz
9
17
24
24
17
Video input
Female Connector
Male Connector
Number/signal type ................... 1 DVI-D digital video
Connectors .................................... 1 DVI-D female (DVI input)
1 DVI-D female (DVI loop through)
Minimum/maximum levels ...... 0.5V to 1.0V p-p
Impedance .................................... 50 ohms
Maximum DC offset .................... 0.5V
Figure 5 — DVI connectors
DVI/DFP signals run at a very high frequency and are especially prone
to bad video connections, too many adapters, or excessive cable length.
To avoid the loss of an image or jitter, follow these guidelines:
• Do not exceed 16.4 feet (5 meters) on the input or buffered loop-
through of the converter.
Video output
Number/signal type ................... 1 RGBHV, RGBS, RGsB
Connectors .................................... 6 BNC female
The missing connectors on the included DVI cable are not
required for the single link of DVI-D data supported by the
DVI-RGB 100. These pins are grayed out on the following table.
6
DVI-RGB 100 • Operation
DVI-RGB 100 • Operation
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum/maximum levels ...... 0.7V to 1.4V p-p (continuously adjustable)
Impedance .................................... 75 ohms
Return loss .................................... -35dB @ 5 MHz
DC offset ....................................... 5mV maximum with input at 0 offset
Sync
Output type .................................. RGBHV, RGBS, RGsB
Output level .................................. TTL (5V p-p) (unterminated)
Output impedance....................... 75 ohms
Polarity .......................................... Positive or negative (follows input)
General
Power ............................................. 100VAC to 240VAC, 50/60 Hz, 25 watts, internal,
auto-switchable.
Product requires 0.15 A to 0.3 A.
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) / 10% to
90%, non-condensing
Operating +32° to +122°F (0° to +50°C) / 10% to
90%, non-condensing
Rack mount................................... Yes, with optional rack shelf, part #60-190-01
Enclosure type .............................. Metal
Enclosure dimensions ................. 1.7" H x 8.7" W x 6.0" D (1U high, half rack
width)
4.3 cm H x 22.1 cm W x 15.2 cm D
(Depth excludes connectors and knobs.)
Product weight ............................. 1.6 lbs (0.7 kg)
Shipping weight .......................... 4 lbs (1.8 kg)
Vibration ....................................... ISTA/NSTA 1A in carton (International Safe
Transit Association)
Listings .......................................... UL, CUL
Compliances ................................. CE, FCC Class A, VCCI, AZ/NZS, ICES
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
Specifications are subject to change without notice.
Optional Adapters and Cables
• 26-497-01 DVI (male), DFP (female)
• 26-498-01 DVI (female), DFP (male)
• 26-535-01 DVI-D M-M extension cable, 6.6’
• 26-535-02 DVI-D M-M extension cable, 9.9’
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
714.491.1500
+31.33.453.4040
+65.6383.4400
Fax 714.491.1517
Fax +31.33.453.4050
Fax +65.6383.4664
Fax +81.3.3511.7656
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2002 Extron Electronics. All rights reserved.
|