Exmark Lawn Mower Lazer Z AS User Manual

ULTRA VAC®  
LAZER Z®, LAZER Z® XP,  
LAZER Z® XS AND  
LAZER Z® AS MODELS  
For Ultra Vac Serial Nos.  
720,000 & Higher  
(to fit Units 352,000 & Higher)  
Part No. 4500-192 Rev. A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
CONGRATULATIONS on the purchase of your  
Exmark Ultra Vac. This product has been carefully  
designed and manufactured to give you a maximum  
amount of dependability and years of trouble-free  
operation.  
This manual contains operating, maintenance,  
adjustment, and safety instructions for your Exmark  
Ultra Vac  
BEFORE OPERATING YOUR MOWER,  
CAREFULLY READ THIS MANUAL IN ITS  
ENTIRETY.  
By following the operating, maintenance, and safety  
instructions, you will prolong the life of your Ultra  
Vac, maintain its maximum efficiency, and promote  
safe operation.  
Figure 1  
1. Model and serial number location  
If additional information is needed, or should you  
require trained mechanic service, contact your  
authorized Exmark equipment dealer or distributor.  
Model No.  
Serial No.  
All Exmark equipment dealers and distributors are  
kept informed of the latest methods of servicing  
and are equipped to provide prompt and efficient  
service in the field or at their service stations. They  
carry ample stock of service parts or can secure them  
promptly for you from the factory.  
All Exmark parts are thoroughly tested and inspected  
before leaving the factory, however, attention is  
required on your part if you are to obtain the fullest  
measure of satisfaction and performance.  
Whenever you need service, genuine Exmark parts,  
or additional information, contact an Authorized  
Service Dealer or Exmark Customer Service and have  
the model and serial numbers of your product ready.  
Figure 1 identifies the location of the model and serial  
numbers on the product. Write the numbers in the  
space provided.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Contents  
Introduction ........................................................... 3  
Torque Requirements .................................... 11  
Periodic Maintenance ....................................... 17  
Check Blower Housing/Impeller................... 17  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety  
• Never let children or untrained people operate  
Safety  
Safety Alert Symbol  
This Safety Alert Symbol (Figure 2) is used both in  
this manual and on the machine to identify important  
safety messages which must be followed to avoid  
accidents  
or service the equipment. Local regulations may  
restrict the age of the operator.  
• The owner/user can prevent and is responsible  
for accidents or injuries occurring to himself or  
herself, other people or property.  
Preparation  
This symbol means: ATTENTION! BECOME  
ALERT! YOUR SAFETY IS INVOLVED!  
• Evaluate the terrain to determine what accessories  
and attachments are needed to properly and safely  
perform the job. Only use on machines approved  
by Exmark.  
• Wear appropriate clothing including safety glasses,  
substantial footwear, long trousers, and hearing  
protection. Do Not operate when barefoot or  
when wearing open sandals.  
Figure 2  
1. Safety alert symbol  
The safety alert symbol appears above information  
which alerts you to unsafe actions or situations  
and will be followed by the word DANGER,  
WARNING, or CAUTION.  
CAUTION  
This machine produces sound levels in  
excess of 85 dBA at the operator’s ear and  
can cause hearing loss through extended  
periods of exposure.  
DANGER: White lettering / Red background.  
Indicates an imminently hazardous situation which, if  
not avoided, Will result in death or serious injury.  
Wear hearing protection when operating this  
machine.  
WARNING: Black lettering / Orange background.  
Indicates a potentially hazardous situation which, if  
not avoided, Could result in death or serious injury.  
• Inspect the area where the equipment is to be  
used and remove all rocks, toys, sticks, wires,  
bones, and other foreign objects which can be  
thrown by the machine and may cause personal  
injury to the operator or bystanders.  
CAUTION: Black lettering / Yellow background.  
Indicates a potentially hazardous situation which, if  
not avoided, May result in minor or moderate injury.  
This manual uses two other words to highlight  
information. Important calls attention to special  
mechanical information and Note emphasizes  
general information worthy of special attention.  
Operation  
• Operate only in daylight or good artificial light,  
keeping away from holes and hidden hazards.  
• Never mow with the discharge deflector raised,  
removed or altered unless there is a grass  
collection system or mulch kit in place and  
working properly.  
Safe Operating Practices  
Training  
• Read the tractor and Ultra Vac Operator’s Manuals  
and other training material. If the operator(s) or  
mechanic(s) can not read English it is the owner’s  
responsibility to explain this material to them.  
• Become familiar with the safe operation of the  
equipment, operator controls, and safety signs.  
• All operators and mechanics should be trained.  
The owner is responsible for training the users.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Safety  
Slope Operation  
DANGER  
Use Extreme caution when mowing and/or turning  
on slopes as loss of traction and/or tip-over could  
occur. The operator is responsible for safe operation  
on slopes.  
There are rotating blades in the blower and  
under the mower deck. Blade contact can  
cause serious operator or bystander injury  
or even death.  
• Do Not reach into blower unless rotation  
indicator has stopped. Disengage PTO,  
stop engine, remove key, wait for all  
moving parts to stop. engage parking  
brake.  
DANGER  
Operating on wet grass or steep slopes can  
cause sliding and loss of control. Wheels  
dropping over edges, ditches, steep banks, or  
water can cause rollovers, which may result  
in serious injury, death or drowning.  
• Never operate mower unless discharge  
deflector, entire grass collection system,  
or mulch kit is installed.  
• Do Not mow slopes when grass is wet.  
• Do Not mow near drop-offs or near water.  
• Stop engine, wait for all moving parts to stop,  
remove key and engage parking brake:  
• Do Not mow slopes greater than 15  
degrees.  
– Before checking, cleaning or working on the  
mower.  
• Reduce speed and use extreme caution  
on slopes.  
– After striking a foreign object or abnormal  
vibration occurs (inspect the mower for  
damage and make repairs before restarting  
and operating the mower).  
• Avoid sudden turns or rapid speed  
changes.  
• See inside the back cover to determine the  
approximate slope angle of the area to be mowed.  
– Before clearing blockages.  
– Whenever you leave the mower.  
• Use a walk behind mower and/or a hand trimmer  
near drop-offs, ditches, steep banks or water.  
(Figure 3).  
WARNING  
Hands, feet, hair, clothing, or accessories can  
become entangled in rotating parts. Contact  
with the rotating parts can cause traumatic  
amputation or severe lacerations.  
• Do Not operate the machine without  
guards, shields, and safety devices in  
place and working properly.  
• Keep hands, feet, hair, jewelry, or clothing  
away from rotating parts.  
• Stop the blades, slow down, and use caution when  
crossing surfaces other than grass and when  
transporting the mower to and from the area to  
be mowed.  
Figure 3  
1. Safe Zone-Use the mower here on slopes less than 15  
degrees  
2. Danger Zone-Use a walk behind mower and/or hand  
trimmer near drop-offs and water.  
• Be aware of the mower discharge path and direct  
discharge away from others.  
3. Water  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Safety  
• Remove or mark obstacles such as rocks, tree  
limbs, etc. from the mowing area. Tall grass can  
hide obstacles.  
• Watch for ditches, holes, rocks, dips and rises that  
change the operating angle, as rough terrain could  
overturn the machine.  
• Avoid sudden starts when mowing uphill because  
the mower may tip backwards.  
• Be aware that loss of traction may occur going  
downhill. Weight transfer to the front wheels  
may cause drive wheels to slip and cause loss of  
braking and steering.  
• Always avoid sudden starting or stopping on a  
slope. If tires lose traction, disengage the blades  
and proceed slowly off the slope.  
• Follow the manufacturer’s recommendations for  
wheel weights or counter weights to improve  
stability. Always install and remove the Ultra Vac,  
including counter weights, as instructed. Failure  
to do so will cause a reduction in stability or  
traction. Do Not operate the mower with only a  
portion of the Ultra Vac installed.  
• Use extreme care with grass catchers or  
attachments. These can change the stability of the  
machine and cause loss of control. The stability  
and traction of the machine will change as the  
Ultra Vac hopper fills with grass clippings. Use  
progressively greater care on slopes as the hopper  
fills.  
Maintenance and Storage  
• Disengage drives, set parking brake, stop engine  
and remove key or disconnect spark plug wire.  
Wait for all movement to stop before adjusting,  
cleaning or repairing.  
• Use care when checking blades. Wrap the blade(s)  
or wear gloves, and use caution when servicing  
them. Only replace blades. Never straighten or  
weld them.  
• Keep all guards, shields and all safety devices in  
place and in safe working condition.  
• Check all bolts frequently to maintain proper  
tightness.  
• Frequently check for worn or deteriorating  
components that could create a hazard.  
• All replacement parts must be the same as  
or equivalent to the parts supplied as original  
equipment.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety  
Safety and Instructional Decals  
• Keep all safety signs legible. Remove all grease,  
dirt and debris from safety signs and instructional  
labels.  
• New safety signs may be obtained from  
your authorized Exmark equipment dealer or  
distributor or from Exmark Mfg. Co. Inc.  
• Replace all worn, damaged, or missing safety  
signs.  
• Safety signs may be affixed by peeling off the  
backing to expose the adhesive surface. Apply  
only to a clean, dry surface. Smooth to remove  
any air bubbles.  
• When replacement components are installed, be  
sure that current safety signs are affixed to the  
replaced components.  
• Familiarize yourself with the following safety signs  
and instruction labels. They are critical to the safe  
operation of your Exmark commercial mower.  
• If an attachment or accessory has been installed,  
make sure current safety signs are visible.  
1-653554  
1-653558  
103-6607  
98-5954  
103-6606  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Safety  
103-3507  
UV60 and UV6672  
103-3508  
LZUV52 Only  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Specifications  
Model Numbers  
Serial Nos: 720,000 and Higher  
LZUV52–Fits Lazer Z and Lazer Z AS with 52 inch deck.  
UV60–Fits Lazer Z, Lazer Z XP, Lazer Z XS, and Lazer Z AS with 60 inch deck.  
UV6672–Fits Lazer Z, Lazer Z XP, Lazer Z XS, and Lazer Z AS with 66 inch or 72 inch deck.  
Systems  
Overall Length:  
w/Ultra Vac  
52 inch Deck-Air-Cooled 105.70 inches (268.5 cm)  
Bagging System  
• Collection bins:  
52 inch Deck-  
Liquid-Cooled  
106.00 inches (269.1 cm)  
– Commercial grade, cloth mesh bags with  
reinforced bottoms.  
60 inch Deck-SN 599,999 106.65 inches (270.9 cm)  
and Lower Air-Cooled  
– Capacity: 11.0 bushels  
60 inch Deck-SN 600,000 110.04 inches (279.5 cm)  
and Higher Air-Cooled  
52 inch decks: 8 bushels (2 bags and hood)  
60, 66, and 72 inch decks: 13.4 bushels (3  
bags and hood)  
60 inch Deck-SN 599,999 106.90 inches (271.5 cm)  
and Lower Liquid-Cooled  
• Dump Mechanism: Manual lift off  
60 inch Deck-SN 599,999 107.90 inches (274.1 cm)  
and Lower Lazer XP & XS  
• Blower Tube: Fixed, abrasion resistant molded  
polyethylene.  
60 inch Deck-SN 600,000 110.88 inches (281.6 cm)  
and Higher Lazer XP & XS  
• Impeller: 5–bladed, 1/4 inch (6.4 mm) thick  
abrasion resistant steel, with vertical axis.  
66 inch Deck-Air-Cooled 111.59 inches (283.4 cm)  
66 inch Deck-Lazer XP & 112.43 inches (285.6 cm)  
XS  
• Impeller bearings: 1 inch (2.5 cm) sealed  
non-greaseable bearings.  
72 inch Deck-SN 599,999 110.75 inches (281.3 cm)  
and Lower Air-Cooled  
Dimensions  
72 inch Deck-SN 600,000 114.12 inches (289.9 cm)  
and Higher Air-Cooled  
Overall Width:  
72 inch Deck-SN 599,999 111.00 inches (278.3 cm)  
and Lower Liquid-Cooled  
w/Ultra Vac  
52 inch Deck - All  
66.85 inches (169.8 cm)  
72 inch Deck-SN 599,999 112.00 inches (281.9 cm)  
and Lower Lazer XP & XS  
60 inch Deck-SN 599,999 74.44 inches (189.1 cm)  
and Lower & All Lazer AS  
72 inch Deck-SN 600,000 115.37 inches (293.0 cm)  
and Higher Lazer XP & XS  
60 inch Deck-SN 600,000 74.94 inches (190.3 cm)  
and Higher  
66 inch Deck-All  
81.50 inches (207.0 cm)  
72 inch Deck-SN 599,999 86.49 inches (219.7 cm)  
and Lower  
72 inch Deck-SN 600,000 87.38 inches (221.9 cm)  
and Higher  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Product Overview  
Curb Weight:  
Product Overview  
w/Ultra Vac  
52 inch Deck-All  
254 lb (115 kg)  
60 inch Deck-SN 599,999 324 lb (147 kg)  
and Lower & All Lazer AS  
60 inch Deck-SN 600,000 243 lb (110 kg)  
and Higher Air-Cooled  
(except AS)  
60 inch Deck-SN 600,000 261 lb (118 kg)  
and Higher Liquid-Cooled  
66 inch Deck-All  
Air-Cooled  
190 lb (86 kg)  
66 inch Deck-All  
Liquid-Cooled  
208 lb (94 kg)  
Figure 4  
4. Tube  
1. Hood  
2. Weight  
3. Blower  
72 inch Deck-SN 600,000 271 lb (123 kg)  
and Higher  
5. Bag  
72 inch Deck-SN 600,000 190 lb (86 kg)  
and Higher Air-Cooled  
72 inch Deck-SN 600,000 208 lb (94 kg)  
and Higher Liquid-Cooled  
Torque Requirements  
Bolt Location  
Torque  
Impeller Spindle Bottom 55-60 ft-lb (75-81 N-m)  
Nut  
Impeller Spindle Top Nut 75-80 ft-lb (102-108 N-m)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Operation  
on the deck. Verify that all rotation indicators  
have stopped before clearing blower assembly or  
mower deck  
Operation  
Note: Determine the left and right sides of the  
machine from the normal operating position.  
3. To remove the bags, first shut off deck drive, stop  
the engine and wait for all moving parts to stop.  
Open the hood and remove the bags by lifting up  
on the rear of the bag, then unhooking the front  
clip. Empty the bags by inverting them.  
Pre-Start  
Make sure you understand the controls, their  
locations, their functions, and their safety  
requirements.  
4. Reinstall bags, close and latch hood before  
continuing mowing.  
Ensure the blower, belt cover, bags, tube and hood  
are in good condition, properly attached, and latched.  
Tips for mowing conditions:  
• When mowing in areas with sandy soil, use  
low lift blades on the cutting deck and higher  
cutting heights to minimize wear on the blower  
components.  
For units above Serial Number 600,000 with Triton  
decks: Make sure that the adjustable dog leg baffle is  
closed to match the intake into the Ultra Vac Blower.  
• When mowing in wet conditions, such as just after  
a rain or in heavy dew, use low lift blades on the  
cutting deck to minimize plugging of the blower.  
WARNING  
If the deck discharge opening and the blower  
intake opening do not match correctly, it  
will allow objects to be thrown in operator’s  
or bystander’s direction. Also, contact with  
blade could occur. Thrown objects or blade  
contact can cause serious injury or kill you  
or bystanders.  
• Maintaining a ground speed that does not pull  
down the engine RPM will allow for the highest  
productivity and best quality of cut. Bogging the  
engine RPM down by going too fast will cause  
plugging and quality of cut issues.  
• When the bags get full, the sound of the blower  
will change and there will be slight blowout from  
the front right corner of the deck. Emptying the  
bags at this point will minimize the potential for  
the tube to plug.  
Adjust dog leg baffle to match intake  
opening.  
Refer to the Maintenance section and perform all the  
necessary inspection and maintenance steps.  
For units below Serial Number 600,000:  
Anti-blowout kits are available for leaf collection.  
They help to prevent “chasing” the leaves. To  
reduce “plowing” leaves, raise the deck slightly.  
Operating Instructions  
On Triton: Raise front adjustable baffle to  
reduce plowing. Lowering front adjustable baffle  
may prevent “chasing”. Match discharge opening  
to Ultra Vac intake for best performance.  
Mowing  
1. The Ultra Vac blower operates when deck drive  
is engaged. Be sure that all persons are clear  
of the mower deck before engaging the cutting  
blades. Set the throttle to “midway” position. Pull  
outward on the PTO switch to the “ROTATE”  
position. Accelerate to full throttle to begin  
mowing.  
Bagger Removal for Side Discharge  
1. Shut off the deck drive, stop engine and wait for  
all moving parts to stop. Remove key and engage  
parking brake.  
2. To disengage the deck drive and blower, set the  
throttle to “midway” position. Push in on the  
PTO switch to the “STOP” position to stop the  
cutting blades and blower. The cutting blades will  
require a slightly longer amount of time to come  
to a complete stop when the blower is installed  
2. Remove the discharge tube by releasing the  
latches at the blower. Slide the tube off the blower  
outlet and remove the upper end from the hood.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Operation  
Figure 6  
Viewed from the right side  
1. Hairpin  
2. Chute Pivot Pin  
3. Discharge Chute  
Note: Install chute with the tabs to the rear of  
the deck tabs as shown.  
Figure 5  
5. Belt Cover  
WARNING  
1. Clevis Pin  
2. Caster Arm Weight  
3. Hairpin  
6. Blower  
7. Tube  
8. Bags  
An uncovered discharge opening will  
allow objects to be thrown in operator’s or  
bystander’s direction. Also, contact with  
blade could occur. Thrown objects or blade  
contact can cause serious injury or kill you  
or bystanders.  
4. Front Floorpan Weight  
3. Remove the belt cover by loosening the knobs.  
For 60 inch and 66 inch units the outboard knob  
does not need to be removed completely to  
remove the belt cover.  
Never operate mower unless discharge  
deflector, or entire grass collection system, or  
mulch kit is installed.  
CAUTION  
The deck sheave will become very hot.  
Touching a hot deck sheave can cause severe  
burns.  
7. Re-install the plastic belt cover and tighten the  
knobs.  
8. Remove the hair pins and clevis pins holding the  
hood assembly to the mount weldment.  
Allow the deck sheave to cool completely  
before removing the belt.  
9. Lift the hood assembly off the mount.  
10. The removable weights must be removed from  
above the caster wheels (and front of floor pan  
on some units). To remove the caster weights.  
Loosen the clamping knobs until the weight can  
be moved relative to the caster arm. Remove the  
hairpins and clevis pins that hold the weights to  
the caster arms. Carefully lift the weights off of  
the caster arms.  
4. Pull the idler release handle and remove the belt  
from the upper groove of the deck sheave.  
5. Unlatch the front end of the blower. Pivot the  
blower back and lift it off the deck.  
6. Install the discharge chute using the chute pivot  
pin and hairpin (see Figure 6).  
To remove the weight on the front of the floor  
pan, remove the two hairpins that retain it and  
then lift it from the mount plates.  
The weights and brackets bolted to the floor pan  
remain on the unit.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Operation  
Note: The removable weights are heavy. Use  
care when lifting them. Make sure that you can  
hold them securely before lifting them. Use  
caution when positioning your hands so that you  
Do Not set them down on your hands or fingers.  
6. Pull the spring loaded idler back and slip the belt  
over the top spindle deck sheave.  
7. Install the plastic belt cover. On 60 inch and 66  
inch units the outside end of the cover is slotted  
and can slip between the two washers on the belt  
shield stud. The plastic knob does not need to  
be removed. On 72 inch and 52 inch units the  
cover has a hole, and the plastic knob must be  
installed after the cover has been positioned. The  
original belt cover stud must be removed on  
52 inch units.  
Note: The portions of the Ultra Vac bagger that  
are not bolted to the mower are designed to be  
installed or removed in their entirety. Failure to  
do so will cause a reduction in stability or traction.  
Do Not operate the mower with only a portion  
of the Ultra Vac installed.  
8. For Units Serial Number 600,000 and Higher  
with Triton Decks: Adjust position of dog leg  
baffle to match the intake of the Ultra Vac blower  
baffle adjusted too wide may allow objects to be  
thrown from under deck. Baffle adjusted too  
narrow may cause plugging issues.  
CAUTION  
Caster or front floor pan weights installed  
without bagger may cause loss of traction  
and steering control. Loss of control can  
result in an accident, which may cause death,  
injury, or property damage.  
All Units: Slip the upper end of the tube  
assembly into the hood opening. Slide the lower  
end of the tube assembly over the blower outlet  
and align the notch with the tube latch. Latch the  
tube to the blower.  
Install caster or front floor pan weights  
ONLY when bagger is installed.  
11. The machine can now be used for side discharge  
mowing.  
Note: The removable weights are heavy. Use  
care when lifting. Make sure that you can hold the  
weight securely before lifting. Use caution when  
positioning your hands so that you Do Not set  
the weight down on your hands or fingers.  
Bagger Installation for Bagging  
1. Stop engine, remove key, and wait for all moving  
parts to stop. Engage parking brake.  
9. Install the removable weight assemblies over  
the caster arms. On 52 inch and 60 inch Lazer  
Z AS machines and 60 inch Lazer Z machines  
serial number 599,999 and lower, one weight has  
a wide mounting bracket and one has a narrow  
bracket. They will only fit the machine one way.  
Weights for the 60 inch Lazer Z serial number  
600,000 and higher, 60 inch Lazer Z XP, 60 inch  
Lazer Z XS and all 66 inch and 72 inch units are  
interchangeable left and right.  
2. Remove hairpin and chute pivot pin. Remove  
discharge chute. Pivot pin and hair pin may be  
stored in the pivot holes of the discharge chute  
during bagging operation.  
3. Install the bagger assembly onto the mount by  
slipping the hook portion over the top mounting  
tube of the mount weldment (see Figure 5).  
Secure the assembly to the mount using the clevis  
pins and hairpins.  
10. Install a clevis pin and hairpin on each caster  
weight to retain them (see Figure 7).  
4. Install the bag assemblies by inserting the hook  
portion into the slots in the cross bar of the hood  
assembly.  
5. Mount the blower on the deck by sliding the  
mounting pin into the tube at the rear right corner  
of the deck. Swing the blower closed. Adjust the  
position of the front pin to engage the slot in the  
front of the deck. Use the latch to lock the blower  
in this position. Adjust the tension on the latch  
to hold the blower up to the deck, yet allow for  
release by hand.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Transporting  
Transporting a Unit  
Use a heavy-duty trailer or truck to transport the  
machine. Lock brake and block wheels. Securely  
fasten the machine to the trailer or truck with straps,  
chains, cable, or ropes. Be sure that the trailer or truck  
has all necessary lighting and marking as required by  
law. Secure a trailer with a safety chain.  
CAUTION  
This unit does not have proper turn  
signals, lights, reflective markings, or a  
slow moving vehicle emblem. Driving on a  
street or roadway without such equipment  
is dangerous and can lead to accidents  
causing personal injury. Driving on a street  
or roadway without such equipment may also  
be a violation of State laws and the operator  
may be subject to traffic tickets and/or fines.  
Figure 7  
2. Hairpin  
1. Clevis Pin  
11. Units with removable floorpan weight:  
Tighten knob on weight assembly until the weight  
is clamped securely to the caster arm.  
12. Hook weight plate assembly over the top of the  
weight mounting plates and secure with two  
hairpins as shown in Figure 8).  
Do Not drive a unit on a public street or  
roadway.  
Figure 8  
1. Weight Plate Assembly  
2. Hairpin  
Note: The portions of the Ultra Vac bagger that  
are not bolted to the mower are designed to be  
installed or removed in their entirety. Do Not  
operate the mower with only a portion of the  
Ultra Vac installed.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Operation  
minimize the ramp angle. The trailer or truck should  
be as level as possible.  
WARNING  
Loading a unit on a trailer or truck increases  
the possibility of backward tip-over.  
Backward tip-over could cause serious injury  
or death.  
Important: Do Not attempt to turn the unit  
while on the ramp, you may lose control and  
drive off the side.  
Avoid sudden acceleration when driving up a ramp  
and sudden deceleration when backing down a ramp.  
Both maneuvers can cause the unit to tip backward.  
• Use extreme caution when operating a  
unit on a ramp.  
• Use only a single, full width ramp; Do  
Not use individual ramps for each side  
of the unit.  
• If individual ramps must be used, use  
enough ramps to create an unbroken  
ramp surface wider than the unit.  
• Do Not exceed a 15° angle between ramp  
and ground or between ramp and trailer  
or truck.  
• Avoid sudden acceleration while driving  
unit up a ramp to avoid tipping backward.  
• Avoid sudden deceleration while backing  
unit down a ramp to avoid tipping  
backward.  
Loading a Unit  
Empty grass bags before attempting to load  
unit on trailer or truck. Use extreme caution when  
loading units on trailers or trucks. One full width  
ramp that is wide enough to extend beyond the rear  
tires is recommended instead of individual ramps for  
each side of the unit. The lower rear section of the  
tractor frame extends back between the rear wheels  
and serves as a stop for tipping backward. Having  
a full width ramp provides a surface for the frame  
members to contact if the unit starts to tip backward.  
If it is not possible to use one full width ramp, use  
enough individual ramps to simulate a full width  
continuous ramp.  
Ramp should be long enough so that the angles  
between the ramp and the ground and the ramp and  
the trailer or truck Do Not exceed 15°. A steeper  
angle may cause mower deck components to get  
caught as the unit moves from ramp to trailer or  
truck. Steeper angles may also cause the unit to tip  
backward. If loading on or near a slope, position  
the trailer or truck so it is on the down side of the  
slope and the ramp extends up the slope. This will  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Maintenance  
Note: Determine the left and right sides of the machine from the normal operating position.  
WARNING  
WARNING  
While maintenance or adjustments are being  
made, someone could start the engine.  
Accidental starting of the engine could  
seriously injure you or other bystanders.  
The engine can become very hot. Touching  
a hot engine can cause severe burns.  
Allow the engine to cool completely before  
service or making repairs around the engine  
area.  
Remove the key from the ignition switch,  
engage parking brake, and pull the wire(s)  
off the spark plug(s) before you do any  
maintenance. Also push the wire(s) aside  
so it does not accidentally contact the spark  
plug(s).  
Recommended Maintenance Schedule(s)  
Maintenance Service  
Maintenance Procedure  
Interval  
• Check the blower housing/impeller.  
• Check bags.  
• Clean muffler and rear frame area.  
Before each use or daily  
• Clean rear screen in the hood.  
• Lubricate grease fittings.  
• Check condition of belt.  
• Clean blower.  
Every 25 hours  
Every 50 hours  
Yearly or before storage  
Periodic Maintenance  
Check Bags  
Service Interval: Before each use or daily  
Check Blower  
Housing/Impeller  
1. Stop engine, wait for all moving parts to stop, and  
remove key. Engage parking brake.  
2. Inspect the bags for wear, tears, or damage.  
Service Interval: Before each use or daily  
1. Stop engine, wait for all moving parts to stop, and  
remove key. Engage parking brake.  
WARNING  
Under normal use the bag will deteriorate  
and wear. Objects could exit through worn  
bag at high speeds. Thrown objects can  
cause serious injury or kill you or bystanders.  
2. Inspect for wear or damage daily. Replace or  
repair worn parts as needed  
Note: When mowing in areas with sandy soil,  
use low lift blades on the cutting deck and higher  
cutting heights to minimize wear on the blower  
components.  
Check bags frequently for tears and holes.  
Replace worn bags.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Maintenance  
Lubricate Grease Fittings  
Note: See chart for service intervals.  
1. Stop engine, wait for all moving parts to stop, and  
remove key. Engage parking brake.  
2. Lubricate fittings with NGLI grade #2  
multi-purpose gun grease.  
Refer to the following chart for fitting locations  
and lubrication schedule.  
Figure 9  
View From Top of Blower  
Lubrication Chart  
1. Spring loaded idler  
4. Belt guide  
Fitting  
Locations  
Initial  
Pumps  
Number of  
Places  
Service  
Interval  
2. Impeller sheave  
3. Fixed idler  
5. Deck sheave (reference)  
1–2  
1
25 Hours  
1. Idler  
Bushings  
3. Remove the old belt.  
4. Install the new belt onto the blower assembly as  
shown in Figure 9.  
Check Condition of Belt  
Service Interval: Every 50 hours  
All Units  
5. Reinstall the belt guide removed in step 2.  
6. Reinstall the blower onto the deck.  
For 52 inch Units Only-Inspect Belt Position on  
the Idler Arm:  
1. Stop engine, wait for all moving parts to stop, and  
remove key. Engage parking brake.  
The idler arm may become bent during use or  
transport. A bent idler arm could cause the belt to  
jump off of the idler and be damaged.  
2. Inspect the belt for damage or wear. Replace belt  
with one of the following:  
Part No.  
1–653438  
103-0866  
Deck  
1. Make sure the belt cover is installed and run the  
blower for one to two minutes.  
52 inch–All  
60 inch Lazer Z, XS, XP  
SN 599,999 and Lower and  
All Lazer AS  
2. Shut off the deck drive, stop engine, wait  
for all moving parts to stop and remove key.  
Engage parking brake. Remove the belt cover  
and check to make sure that the belt is riding near  
the center of the flat idler on the idler arm.  
103-0867  
72 inch All SN 599,999  
and Lower  
60 inch Triton  
66 inch Triton  
72 inch Triton  
109-1242  
103-0867  
109-1244  
3. If the belt is not riding near the center of the  
idler, remove the blower, and bend the idler arm  
slightly.  
4. Reinstall the blower and belt cover and repeat  
steps 1 through 3 until the belt is positioned near  
the center of the idler.  
For 52 inch Units Only-Belt Replacement  
Procedure:  
1. Remove the blower from the deck.  
2. Remove the belt guide on the blower (see  
Figure 9).  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Maintenance  
Cleaning  
Clean Muffler and Rear  
Frame Area  
Service Interval: Before each use or daily  
Stop engine, wait for all moving parts to stop, and  
remove key. Engage parking brake.  
WARNING  
Operating engine parts, especially the  
muffler, become extremely hot. Severe burns  
can occur on contact and debris, such as  
leaves, grass, brush, etc. can catch fire.  
• Allow engine parts, especially the muffler,  
to cool before touching.  
• Remove accumulated debris from muffler  
and engine area.  
• Install and maintain in working order a  
spark arrester before using equipment  
on forest-covered, grass-covered,  
brush-covered unimproved land.  
Clean Rear Screen In Hood  
Service Interval: Before each use or daily  
1. Stop engine, wait for all moving parts to stop, and  
remove key. Engage parking brake.  
2. Open hood and remove clippings that are stuck  
to the screen.  
Clean Blower  
Service Interval: Yearly or before storage  
Grass build up may cause problems with the impeller  
when the unit is put back into operation.  
1. Stop engine, wait for all moving parts to stop, and  
remove key. Engage parking brake.  
2. Remove grass buildup from around the impeller  
before placing it in storage.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Troubleshooting  
Troubleshooting  
Important: It is essential that all operator safety mechanisms be connected and in proper operating  
condition prior to mower use.  
When a problem occurs, Do Not overlook the simple causes. For example: starting problems could be  
caused by an empty fuel tank.  
The following table lists some of the common causes of trouble. Do Not attempt to service or replace major  
items or any items that call for special timing or adjustment procedures (such as valves, governor, etc.). Have  
this work done by your Engine Service Dealer.  
Note: When disconnecting electrical connectors Do Not pull on the wires to separate the connectors.  
Problem  
Abnormal vibration.  
Possible Cause  
Corrective Action  
1. Install new cutting blade(s).  
1. Cutting blade(s) is/are bent or unbalanced.  
2. Blade mounting bolt is loose.  
3. Loose blower pulley or pulley assembly.  
4. Blower impeller blades are bent.  
2. Tighten the blade mounting bolt.  
3. Tighten the appropriate pulley.  
4. Contact an Authorized Service Dealer.  
Blower drive belt snaps or breaks frequently.  
Excessive grass blowout from the deck.  
1. Idler arm is out of alignment.  
1. Correct the alignment of the idler arm.  
1. Empty bags more frequently.  
1. Bags are full.  
2. Plugged screen in bagger hood.  
2. Remove debris, leaves or grass clippings  
from the screen.  
3. Ground speed is too fast.  
4. Blower belt is worn, loose, or broken.  
5. Plugged tube or blower.  
6. Conditions are dry.  
3. Drive slower at full throttle.  
4. Install new blower belt.  
5. Locate and remove plugged debris.  
6. Use lower lift blade.  
Blower and tubes plug too frequently.  
1. Bags are too full.  
1. Empty bags more frequently  
2. Ground speed is too fast.  
3. Grass is too wet.  
2. Drive slower at full throttle.  
3. Cut grass when it is dry.  
4. Grass is too long.  
4. Cut grass more frequently or at higher cut  
height.  
5. Plugged screen in bagger hood.  
5. Remove debris, leaves, or grass clippings  
from the screen.  
6. Blower drive belt is worn, loose, or  
broken.  
6. Install new belt.  
7. Blower is plugged.  
7. Use low lift blades in wet conditions.  
Blower impeller does not spin freely.  
1. Plugged blower.  
1. Remove debris, leaves, or grass clippings  
from the blower impeller.  
2. Impeller not aligned.  
1. Deck is too low.  
2. Contact an Authorized Service Dealer.  
Plowing leaves.  
Chasing leaves.  
1. Units below Serial Number  
600,000: Raise the deck slightly.  
Triton: Raise the front adjustable baffle.  
1. Units below Serial Number 600,000:  
Install an anti-blowout kit–contact  
an Authorized Service Dealer.  
Triton: Lower the front adjustable  
baffle. Match discharge opening to Ultra  
Vac intake.  
1. Blowout from deck.  
Blower components show signs of wear  
and/or air cleaners and cooling fins are dirty.  
1. Sand or dry conditions.  
1. Use low lift blades on the cutting  
deck and higher cutting heights.  
Clean air cleaners and cooling fins  
frequently.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2-Year Limited Warranty  
Exmark Turf Equipment  
(For units purchased on or after October 1, 2004)  
Contact any Exmark Service Dealer to arrange service at their  
Conditions and Products Covered  
Exmark Mfg. Co. Inc. and its affiliate, Exmark Warranty  
Company, pursuant to an agreement between them, jointly  
warrant on the terms and conditions herein, that we will repair,  
replace or adjust any part manufactured by Exmark and found  
by us (in the exercise of our reasonable discretion) to be  
defective in factory materials or workmanship for a period of  
two years.  
dealership. To locate a dealer convenient to you, access our  
402-223-6375.  
If for any reason you are dissatisfied with the Service Dealer’s  
analysis or with the assistance provided, contact us at:  
Exmark Customer Service Department  
The Exmark Warranty Company  
2101 Ashland Avenue  
Beatrice, NE 68310  
402-223-6375 or  
This warranty applies to Exmark turf equipment purchased on  
or after October 1, 2004 sold in the US or Canada. This  
warranty may only be assigned or transferred to a second (or  
third) owner by an authorized Exmark dealer. The warranty  
period commences upon the date of the original retail  
purchase.  
Owner’s Responsibilities  
The Exmark turf equipment, including any defective part,  
must be returned to an authorized Exmark service dealer  
within the warranty period. This warranty extends only to turf  
equipment operated under normal conditions. You must read  
the operator’s manual. You must also properly service and  
maintain your Exmark product as described in the operator’s  
manual. Such routine maintenance, whether performed by a  
dealer or by you, is at your expense.  
Products  
Warranty Period  
2 years  
1 year  
1 year  
90 days  
1 Year Prorated  
• All Products (except as noted below)  
• All Attachments and Accessories  
• Metro 21 and Metro 26 Series  
• Belts and Tires  
• Battery  
• Engine*  
Warranty is covered by engine manufacturer  
* Please refer to the engine manufacturer’s warranty statement  
that is included in the literature packet. We are not authorized  
to handle warranty adjustments on engines.  
General Conditions  
The sole liability of Exmark and Exmark Warranty Company  
with respect to this warranty shall be repair and replacement  
of defective components as set forth herein. Neither Exmark  
nor Exmark Warranty Company shall have any liability  
for any other cost, loss or damage, including but not  
limited to, any incidental or consequential loss or damage.  
This warranty only includes the cost of parts and labor.  
Items and Conditions Not Covered  
This warranty does not cover the following:  
• Pickup and delivery charges to and from any authorized  
Exmark Service Dealer beyond first warrantable service.  
• Any damage or deterioration due to normal use, wear and  
tear, or exposure.  
• Cost of regular maintenance service or parts, such as filters,  
fuel, lubricants, tune-up parts, and adjustments.  
• Any product or part which has been altered or misused or  
required replacement or repair due to normal wear,  
accidents, or lack of proper maintenance.  
• Any repairs necessary due to use of parts, accessories or  
supplies, including gasoline, oil or lubricants, incompatible  
with the turf equipment or other than as recommended in  
the operator's manual or other operational instructions  
provided by Exmark.  
In particular, we shall have no liability or responsibility for:  
• Expenses related to gasoline, oil or lubricants.  
• Travel time, overtime, after hours time or other  
extraordinary repair charges or charge relating to repairs or  
replacements outside of normal business hours at the place  
of business of the authorized Exmark Service Dealer.  
• Rental of like or similar replacement equipment during the  
period of any warranty, repair or replacement work.  
• Any telephone or telegram charges or travel charges.  
• Loss or damage to person or property other than that  
covered by the terms of this warranty.  
• Any claims for lost revenue, lost profit or additional cost as  
a result of a claim of breach of warranty.  
• Attorney's fees.  
There are no other express warranties except for engine and  
special emission system coverage stated elsewhere herein or  
included with the product.  
No Claim of breach of warranty shall be cause for cancellation  
or rescission of the contract of sale of any Exmark mower.  
All warranty work must be performed by an authorized  
Exmark Service Dealer using Exmark approved replacement  
parts.  
Some states do not allow exclusions of incidental or  
consequential damages, so the above exclusions and  
limitations may not apply to you.  
Instructions for Obtaining Warranty Service  
The product must be registered with original proof of purchase  
by an Exmark Service Dealer before obtaining any warranty  
service.  
This warranty gives you specific legal rights, and you may  
also have other rights which vary from state to state.  
G006117  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service Record  
Date:  
Description of Work Done:  
Service Done By:  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEE EXMARK’S COMPLETE LINE OF ACCESSORIES  
MID-MOUNT RIDING ACCESSORIES  
CUSTOM RIDE SEAT SUSPENSION SYSTEM  
DECK LIFT ASSIST KIT  
HITCH KIT  
ROLL OVER PROTECTION SYSTEM (ROPS)  
SNOW BLADE  
SUN SHADE  
LAZERLOCKER  
TRASH CONTAINER  
LIGHT KIT  
TURF STRIPER  
MICRO-MULCH SYSTEM  
OPERATOR CONTROLLED DISCHARGE  
ULTRA VAC COLLECTION SYSTEM  
ULTRA VAC QUICK DISPOSAL SYSTEM  
OUT-FRONT RIDING ACCESSORIES  
CUSTOM RIDE SEAT SUSPENSION SYSTEM  
DUAL-TAIL WHEEL  
SNOW BLADE  
SNOWBLOWER  
FLOOR PAN EXTENDER  
HITCH KIT  
SUN SHADE  
TRASH CONTAINER  
LIGHT KIT  
ULTRA VAC COLLECTION SYSTEM  
ULTRA VAC QUICK DISPOSAL SYSTEM  
WEATHER CAB  
MICRO-MULCH SYSTEM  
ROLL OVER PROTECTION SYSTEM (ROPS)  
ROTARY BROOM  
WALK-BEHIND ACCESSORIES  
GRASS CATCHER  
LAZERLOCKER  
TURF STRIPER  
STANDON  
MICRO-MULCH SYSTEM  
Place Model No. and Serial No.  
Label Here (Included in the Literature  
Pack) or Fill in Below  
Date Purchased  
Model No.  
Serial No.  
© 2000–2007 Exmark Mfg. Co., Inc.  
Industrial Park Box 808  
Beatrice, NE 68310  
Part No. 4500-192 Rev. A  
(402) 223-6300  
Fax (402) 223-5489  
Printed in the USA.  
All Rights Reserved  
Download from Www.Somanuals.com. All Manuals Search And Download.  

ELAN Home Systems Network Card EM78P458 User Manual
Electro Voice Portable Speaker MTH 2 94B User Manual
Extron electronic Switch 68 1383 01 REV E User Manual
Fisher Price Doll B1512 User Manual
Fuego Model Vehicle T0375 User Manual
Fujitsu Server MX130 S2 User Manual
Fujitsu Tablet Accessory FPCCC27 User Manual
GE Beverage Dispenser Profile Wine Chiller User Manual
GE Fryer DBVH520EJ User Manual
GE Oven 840081100 User Manual