Table Of Contents
Introduction ...................................................................................................... 3-4
Advanced System Features............................................................................... 4-5
Transmitter Operations ........................................................................................ 6
Arming the System Using the Transmitter ....................................................... 7-8
Passively Arming the System ........................................................................... 8-9
Security System Armed and Triggered........................................................... 9-11
Disarming the System................................................................................... 11-12
Remote Panic Feature ........................................................................................ 13
Optional 2nd Channel Output (Trunk Release) and 3rd Channel Output .... 13-14
Using the Valet Switch ................................................................................. 14-16
Red LED Status Indicator ............................................................................. 16-18
Audible and Visual Indications .................................................................... 18-19
Auxiliary Optional Sensor Ports with Prewarn ............................................ 22-23
Anti-Carjacking Protection ........................................................................... 23-24
Optional Pager Unit and Backup Battery .......................................................... 24
Programming Transmitters ........................................................................... 25-26
Programming Features.................................................................................. 27-28
Features Programming Checklist.......................................................... Centerfold
Programmable Features ................................................................................ 29-38
Transmitter Options ........................................................................................... 39
"WE'VE GOT THE EDGE ON SECURITY"
OWNER'S MANUAL
AL-1000ATV2
AL-900ATV2
One or more of these patents may apply to this product:
#5,612,578 #5,612,699 #5,654,688 #5,663,704 #382,558 #385,878
#5,719,551 #5,729,191 #5,739,748 #5,750,942 #5,818,329 #5,739,747
COPYRIGHT:OMEGARESEARCH&DEVELOPMENTINC.1999
The Red LED Status Indicator: Informs you of the different conditions the
security system can be in and also serves as a visual deterrent to break-ins and theft.
Introduction
Congratulations on your purchase of your new vehicle security system and on
joining over 8 million people worldwide who have trusted their vehicle's security
to the designers of Omega Research & Development, Inc. To learn how to operate
your security system, please become familiar with the following three principal
user components: the Remote Transmitter, the Red LED Status Indicator and the
Valet Switch.
The Valet Switch: This switch is used for several purposes, one which is being
used to place the system into "Valet Mode". Valet Mode can be used to turn off
automatic functions, such as Last Door Arming or Automatic Rearming. The Valet
Switch is also used, with the ignition key, to disarm the security system in the event
the transmitter becomes inoperable, and this switch is also used in the procedure for
programming features and learning transmitters.
The Remote Transmitter: Each security system includes two pre-learned
transmitters, but if desired up to 4 different transmitters can operate the system. The
transmitter has three buttons: one large button in the middle and two smaller
buttons, one on either side. This system is pre-programmed to have the transmitter
buttons work in the following configuration:
Please spend time reviewing this guide to become familiar with your new
Omega vehicle security system. You will find that your new vehicle security
system will give you years of trouble-free convenience and protection.
The large button is used to arm, disarm and panic the security system.
Advanced System Features
AutomaticTransmitterVerificationTM (ATV): YourOmegavehiclesecurity
system is protected against a common weakness found in all remote controlled
security systems, and even factory-equipped Remote Keyless Entry systems. This
weakness is the ease in which an additional transmitter may be programmed to
operate the system. This vulnerability allows a thief to code his own, unauthorized
Page - 4
The small right button is used to operate the 2nd channel output, typically used
for trunk release, and arm and disarm the system without the audible chirps.
The small left button operates the 3rd channel output and, in conjunction with
the large button, can remotely bypass a sensor upon arming.
Page - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
* The electronic siren features six different tones, and every 5 seconds the siren will change
the tone to generate more attention to the vehicle. The vehicle's horn may be used if desired.
The horn, if used, will honk on and off for 10 seconds, then pause for 5 seconds, repeating
this cycle for the duration of the activated alarm period. This prevents the horn from
overheating. Please ask the installer for details on utilizing the horn.
Additionally, Automatic Last Door Arming may entitle you to an insurance
discount. Please note that the previously mentioned Arming By-Pass feature does
not operate with the Automatic Last Door Arming feature. The bypass feature is
designed to operate only when arming the system with the transmitter and all
protected entries must be closed to initiate the Automatic Last Door Arming
sequence. Last Door Arming does not effect the operation of Active Arming.
To prevent the system from automatically arming while the vehicle is being
refueled you have these options: put the system in Valet Mode (page 14), keep your
door open, or turn on your dome light switch so the system detects that your door
is still open. We do not recommend leaving your ignition key turned "on".
The sirenandthe parking lightswill stayactive for60secondsunless youdisarm
thesystemwiththetransmitterortheValetSwitch. Ifallprotectedentriesaresecure
at the end of 60 seconds, the system will stop and rearm automatically to detect
another entry attempt. If there is a protected entry still open or if an optional sensor
is still in a triggered state at the end of 60 seconds, the system will reactivate for two
more 60 second cycles. In this case the system will stop after a total of 3 minutes
and rearm automatically, while ignoring only the open entry or triggered sensor.
When the entry is closed or the triggered sensor is reset, protection will begin
instantly for the formerly affected circuit.
Oncethesecuritysystemhasbeenactivatedandreset,thedisarmingconfirmation
willnolongerbe2sirenchirps,andtheparkinglightsstayingon.Instead,thesystem
will respond with 4 siren chirps and the parking lights flashing 4 times before
staying on for 30 seconds. The LED Status Light will change to flashing one to four
times between pauses to indicate which protection circuit triggered the system.
These audible and visual indications will remain until the ignition is turned “on”.
Page - 10
Security System Armed And Triggered
While the security system is armed, the LED Status Indicator will be flashing.
Should any intrusion attempt occur, your system will instantly "trigger". Once
triggered, the security system will respond by:
1) The electronic siren will sound*.
2) The parking lights will flash on and off for the duration.
3) The doors will relock. This feature is so unique that the security system can
detect an open door and wait until the door is closed; at that time the door
re-locks so that the thief cannot easily regain entry.
Page - 9
instantly disarm the system and unlock the doors. If you have the optional unlock
driver's door feature, then upon disarming only the driver's door will unlock, and
if the large transmitter button is pressed again within 5 seconds, or at any time if a
door is open, all of the other doors will unlock.
Disarming is confirmed by the siren chirping twice, and the parking lights
turning on for 30 seconds. However, the lights will turn off instantly if the ignition
switch is turned "on". If the system was triggered and reset while you are away, the
disarm confirmation will change to 4 siren chirps, 4 light flashes, and then the lights
will stay on for 30 seconds. The security system will have this response upon
disarming until the ignition switch is turned "on", which clears the unit's memory.
Anytime the security system triggers, the LED Status Light will indicate which
zone triggered the system by flashing one to four times, pausing between flashes.
This code will continue to flash, even after disarming. The system can hold two
different violation codes in it's memory, which is cleared by turning the ignition
switch "on".
Safety Disarm/Storm Mode: While the system is activated, i.e. sounding the
siren and flashing the lights, pressing the large transmitter button will disarm the
system only. The system will not chirp twice or illuminate the parking lights, nor
unlock the doors if the system is configured to also operate the door locks. This
safety feature ensures that the vehicle remain secure should the system require
disarming due to being activated from nuisance or malicious false sensory inputs,
such as typically produced by severe weather conditions. To remotely unlock the
doors if the system is disarmed while activated, repeat the arm/disarm operation by
pressing and releasing the large transmitter button once, then again. If disarmed
from a panic mode, the normal disarm indications are present, including the
unlocking of the doors.
Automatic Rearming Feature: Should you unknowingly press the transmitter
button, which will result in your system disarming, the system can automatically
rearm itself 90 seconds later and once again lock the doors. This feature is
programmable, and may be turned off.
Automatic Rearming can be paused by opening the door or stopped by turning
"on" the ignition switch. Also, Automatic Rearming can be cancelled by the Safety
Disarm/Storm Mode feature; if the system is disarmed while triggered, Automatic
Rearming will not occur. Automatic Rearming is confirmed by a fast flashing LED
StatusIndicatorafterdisarming, unlessthesystemwastriggeredandreset, inwhich
Disarming The System
Disarming The System Using The Transmitter: While the security system is
in the armed state, pressing and releasing the large transmitter button once will
Page - 11
case a Zone Violation code will flash instead.
Page - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional 3rd Channel Output: This output's operation is similar to the trunk
release output except for the following: press the small transmitter button on the left
for 2.5 seconds to activate the 3rd channel output. The 3rd channel output will
operate regardless of the ignition switch being "on" or "off", and there is no audible
or visual confirmation. This output can be used to operate optional equipment such
as remote car starters or window roll-up modules.
Remote Panic Feature
Remote Panic Activation From The Transmitter:Should you feel threatened
or the need to attract attention you can activate your system's Remote Panic feature
at any time by depressing and holding the large transmitter button for 3 seconds.
Your system will respond by sounding the siren, locking the doors and flashing the
exterior and interior lights for the normal activated period of 60 seconds. Should
wish to enter your vehicle or disengage Remote Panic, simply press and release the
large transmitter button.
Using The Valet Switch
The primary function of the Valet Switch is to enter your security system into
ValetMode, whichpreventsthesystemfromarming. Youwillfindthisusefulwhen
stopping at service stations, having your vehicle serviced, having your car valet
parked or while having your car washed. The Valet Switch, in conjunction with the
ignition key, can be used to disarm the system should your transmitter be lost or
become inoperable. The Valet Switch is typically mounted in same housing as the
LED Status Indicator. However, some custom installations may have the Valet
Switch mounted in a hidden location; if so, be sure your installing dealer indicates
the location of the Valet Switch to you to avoid potential inconvenience.
Optional 2nd Channel and 3rd Channel Output
Optional 2nd Channel Output (Trunk Release): If your vehicle is equipped
with electric trunk release, your installing dealer can configure your system to
accomplish trunk release from your transmitter. Use of the 2nd channel output is
recommended to operate this option; simply press and hold the small transmitter
button on the right for 2.5 seconds. Your vehicle will respond by releasing the trunk
lidorrearhatch, chirpingthesirentwice, disarmingthesystem, unlockingthedoors
and turning on your parking lights for 30 seconds. The trunk release will not operate
with the ignition switch "on" unless the vehicle's door is open. If desired, the
security system can be programmed to remain armed when this feature is used.
Page - 13
Normal Valet Mode: This unique feature can be activated anytime the system
is disarmed and allows you to enter the Valet Mode by simply depressing and
Page - 14
holding the Valet Switch, provided the system is not armed. If the system is armed
orinthetriggeredstate,however,theignitionmustbeturned"on"andthentheValet
Switch must pressed within 5 seconds to disarm the system and enter Valet Mode.
While the system is disarmed, simply press and hold the Valet Switch for 2
seconds to activate the Valet Mode. The system will confirm that it is in the Valet
Mode by chirping the siren twice, and the LED Status Indicator will illuminate
steady Red. The security system will stay in the Valet Mode when the ignition
switch is "on" or "off". While in the Valet Mode, although the system will not arm,
the transmitters will still operate the Remote Panic feature, the doorlocks, and trunk
release; the doors will also lock when the ignition switch is turned "on" and unlock
when it is turned "off"'. While the security system is in the Valet Mode, every time
the ignition switch is turned "off", the siren will chirp once as a reminder.
STEP 1. With the system in the armed condition, enter via the driver's door (be
aware that the security system will trigger the when the door is opened).
STEP 2. Use the ignition key to turn the ignition switch "on".
STEP 3. Within 5 seconds, press the Valet Switch. The system will disarm.
Red LED Status Indicator
The LED Status Indicator feature is a visual indication of what state the security
system is in at any given time. The LED Status Indicator is normally positioned in
alocationthatiseasilyobservedbythedriver. Thesearethepossibleconditionsthat
the security system can be in as reflected by the LED Status Indicator:
1) Off
= The security system is disarmed and not performing any
automatic functions.
= The security system is in the Valet Mode.
= The security system is Fully Armed.
= The 30 second Last Door Arming feature or 90 second
Automatic Rearming feature is in progress. This fast
flashing also occurs during the 3 second or 45 second
To Exit Valet Mode: Simply press the Valet Switch, and instantly the security
system will exit Valet Mode. To confirm that the Valet Mode is turned off, the LED
Status Indicator will turn off.
2) On Constant
3) Flashing Slow
4) Flashing Fast
Disarming The Security System If The Transmitter Is Lost: In the event the
transmitter is lost, damaged, or its batteries become exhausted, the Valet Switch
and your ignition key can be used to disarm the system:
arming delay.
Page - 15
Page - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Transmitter VerificationTM: After the ignition is turned "on", the
LED Status Indicator will flash and pause to indicate the number of transmitters
programmed to operate your security system. For example: two flashes and pause
indicates that only two transmitters are encoded to operate your system. Whenever
youleave yourvehicleandkeyswithsomeone,youwillnowhavethepeaceofmind
in knowing that only your transmitters will operate the security system and that no
additional transmitters have been coded into your system for the purpose of stealing
yourvehicleoritscontents.ThisIndicatorflashingoccursfor10secondseverytime
the ignition switch is turned "on".
10) Flash-2x & Pause = The security system was triggered from the hood, trunk
or #2 Auxiliary Port circuit.
11) Flash-3x & Pause = The security system was triggered from the door circuit
.
12) Flash-4x & Pause = The security system wastriggered from the #1 Auxiliary
Sensor Port circuit.
Audible And Visual Indications
5) Flash-1x & Pause = 1 transmitter code is stored in the system's memory.
6) Flash-2x & Pause = 2 transmitter codes are stored in the system's memory.
7) Flash-3x & Pause = 3 transmitter codes are stored in the system's memory.
8) Flash-4x & Pause = 4 transmitter codes are stored in the system's memory.
The Security system's audible output and the vehicle's parking and interior lights
are utilized to indicate a number of events or processes associated with the system's
operation:
1) One siren chirp and one light flash upon closing the vehicle's door: The system
has started a passive Last Door Arming countdown and will become armed after
the 30 second countdown expires. This chirp indicates that the starter interrupt
will engage and the doors will lock when the alarm becomes fully armed in 30
seconds.
2) One siren chirp, one light flash, & doors lock: The system has armed passively
or actively from the transmitter. The starter interrupt has engaged and the doors
have locked. The optional sensor will become operational 5 seconds later.
Page - 18
Zone Violation: If the system is triggered, the LED Status Indicator will start
toflashandpauseoneofthefollowingsequencestoindicatewhichprotectedcircuit
triggered the system. This is seen while the system is armed, and after disarming,
until the ignition switch is turned "on", which will clear the Zone Violation code.
The unit's memory can store two different violation codes.
9) Flash-1x & Pause
= The security system was triggered from the current
sensing circuit.
Page - 17
3) One siren chirp after the arming chirp previously mentioned: The auxiliary
sensor circuit is bypassed by pressing the small transmitter button within 3
seconds of pressing the large transmitter button.
4) One siren chirp, and no light flash, but only at the moment the ignition switch is
turned "off": The alarm is in Valet Mode, and will not arm actively or passively.
5) Two siren chirps and the parking lights stay on for 30 seconds:
The system has just disarmed or 2nd channel output has been activated.
6) Two siren chirps and two light flashes: The system has entered the Valet Mode.
7) Four siren chirps and the lights stay on for 30 seconds: The system has just
disarmed and was activated while you were away. The system will have this
disarming confirmation until the ignition switch is turned "on".
8) Sirensounding, changingsoundsevery5seconds, andtheparkinglightsflashing
on and off: The system is in an activated state. This will also relock the doors.
9) A series of siren chirps lasting two seconds after the ignition switch is turned
"on": The Automatic Transmitter VerificationTM feature (page 4) has been
activated. This will also occur for 48 hours after installation.
10) Three siren chirps upon arming the system: The Zone Bypass feature is
indicating that the system is arming, but bypassing a violated protected zone.
11) Three siren chirps while the system is armed: The Prewarning feature has been
activated.
Page - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
the interior zone of the radar sensor intact, reducing a possible false alarm caused
by parking in an area of heavy traffic or other vibrations, while leaving the radar
sensor's interior zone as part of the security system's protection. The dual auxiliary
ports' operation allows extreme flexibility in designing a custom security system.
If the system is triggered by the sensor plugged into Port #1 the Zone Violation
feature will flash the LED Status Light four times between pauses. If the system is
triggered by a sensor plugged into Port #2 the Zone Violation feature will flash the
LED Status Light twice between pauses.
Auxiliary Optional Sensor Ports With Prewarn
Your vehicle security system features two ports which allows an optional
auxiliary sensor to be easily added to increase the effectiveness of your system. A
light shock or impact to the vehicle will initiate the Prewarn feature, while a heavier
shock or impact will trigger the security system. Other sensors are available which
include those that monitor shock to the vehicle, detect changes in atmospheric
pressure within the vehicle, and radar sensors that can detect motion inside and
outside the vehicle. The sensor may be temporarily bypassed using the transmitter.
The following differences in operation of the two auxiliary sensor ports
concerning the sensor bypass feature should be noted: Port #1, which is on the
corner of the security system control module, will have both the instant trigger and
the prewarn trigger bypassed when this feature is utilized. Port #2, just inboard of
Port #1, will have only the prewarn trigger and not the negative instant trigger
bypassed. This allows the option, when installing a single sensor, of having both
prewarn and instant triggers bypassed (Port #1) or just the prewarn trigger bypassed
(Port #2). When using two sensors, the most sensitive of the two sensors will
generally be plugged into Port #1. An example of this flexibility would be a
sensitive shock sensor plugged into Port #1 and a radar sensor plugged into Port #2.
When the remote sensor bypass feature is used, the shock sensor will be completely
Prewarning Shock Detection Circuit: This circuit requires connection to an
auxiliary detection sensor device. When the sensor is triggered by a light impact or
shock to the vehicle, the security system will respond by chirping the siren (or
honking the horn) 3 times and locking all of the doors. After this circuit has been
triggered 5 times it will automatically shutdown until the alarm system is rearmed
again. This will prevent the security system from being a nuisance to the general
public, and in some cases to allow compliance with local noise ordinances.
Anti-Carjacking Protection
This security system features three optional forms of Anti-Carjacking protec-
tion. The Anti-Carjacking features may be activated by turning "on" the ignition
switch, opening and closing a door after the ignition has been turned "on", or by the
bypassedandtheexteriorzoneoftheradarsensorwillalsobebypassed. Thisleaves
Page - 22
Page - 23
Download from Www.Somanuals.com. All Manuals Search And Download.
transmitter activating the 3rd Channel Output, but only when the ignition is "on".
The Anti-Carjacking feature automatically activates for each of the three
described conditions, provided that each has been programmed to operate. In each
of the three methods, the vehicle operator has 53 seconds to press the Valet Switch
to cancel the Anti-Carjacking feature. If not cancelled, at 53 seconds the siren will
start chirping, to remind the operator that Anti-Carjacking will engage. This will
continue for 7 seconds, during which time the Anti-Carjacking feature may still be
cancelled by pressing the Valet Switch. At 60 seconds, the Anti-Carjacking feature
fully engages, sounding the siren and flashing the parking lights. Thirty seconds
after the siren sounds and the parking lights flash, the starter interrupt will engage.
During this 30 second period, if the ignition is turned "off" the starter interrupt will
instantly engage.
Once fully activated, the Anti-Carjacking feature can only be deactivated by
turning the ignition "off", then "on" again, after which the Valet Switch must be
pressed within 5 seconds. When the Anti-Carjacking feature is fully engaged, the
system will not respond to the transmitters, nor will it automatically reset after 60
seconds. The Anti-Carjacking operation will continue until deactivated or until the
vehicle's battery is drained.
Optional Pager Unit And Backup Battery
This security system is designed for easy compatibility with the Omega Pager
unit and also for a Backup Battery (both of which are optional additional compo-
nents). The Omega Pager will alert the user to a security system violation, and also
indicate which protected zone caused the violation. The Backup Battery option will
allow the security system to operate even if power is removed from the system's
control module or if the vehicle's battery is disconnected. The Omega dealer from
which you purchased your vehicle security system can provide more details on the
exact operations of each of these options.
Programming Transmitters
When adding or deleting transmitter codes to operate the security system,
follow this process:
1) Turn "on" the ignition.
2) Within5secondsofturning"on"theignition,presstheValetSwitch5times.The
siren will chirp, confirming that for the next 10 seconds the system is ready to
learn a transmitter code. When the first transmitter code is learned all existing
storedcodeswill be erased. Toentera transmittercode, simply press andrelease
Page - 24
Page - 25
the transmitter button which is desired to arm and disarm the system.
Programming Features
Your vehicle security system has 22 programmable features that allow your
system to be customized to fit your personal needs. To program these features "on"
or "off", follow this process:
3) Repeatthisprocedureforeachtransmitterdesiredtooperatethesecuritysystem.
The system will chirp the siren once to confirm that each transmitter code was
learned. Both of the other two transmitter button's functions will automatically
be learned when the arm / disarm button is learned. If a code is not received
within a 10 second period, the learning process will automatically terminate.
1) Turn "off" the ignition.
2) Within 5 seconds of turning "off" the ignition, press the Valet Switch 5 times.
The siren will chirp, followed by a short siren burst, confirming that for the next
10 seconds the system is ready to receive a feature number.
Although this security system is programmed at the factory for the large center
transmitter button to arm and disarm the system, any one of the transmitter's three
buttons may be programmed to arm and disarm the security system. Upon the
system learning the arm / disarm button, the other two buttons are automatically
assigned other functions, as follows:
3) Press the Valet Switch the number of times that is equal to the feature number.
Example: Press the Valet Switch six times if Feature #6 is to be changed.
Arm / Disarm
Large Center Button
Small Right Button
Small Left Button
Trunk Release
Small Right Button
Large Center Button
3rd Channel
4) The siren will respond by chirping the same amount as the feature number.
Example: The siren responds with six chirps.
Small Left Button
Small Left Button
Small Right Button
5) Press the large transmitter button to turn the feature "on". When done, the siren
will respond with one chirp.
Large Center Button
Page - 26
Page - 27
Download from Www.Somanuals.com. All Manuals Search And Download.
6) Press the small left transmitter button to turn the feature "off". When done, the
siren will respond with two chirps.
15)
16)
17)
18)
19)
20)
21)
22)
3 / 45 Second Arming Delay: Default 3 Seconds.
Confirmation Chirp: Default ON.
30 / 60 Second Activated Alarm Cycle: Default 60 Seconds.
Pulsed Horn / Steady Siren Output: Default Steady Siren.
Loud / Soft Pulsed Horn Chirps: Default Loud.
Total Closure Lock Output: Default OFF.
If the Valet Switch is not pressed or if a transmitter signal is not received within a
10 second period, the Programmable Features learning process will automatically
terminate. The 22 Programmable Features are:
Remote-Activated Anti-Carjacking Protection: Default OFF.
One / Two Button Arming / Disarming: Default One Button.
1)
2)
3)
Ignition-Activated Anti-Carjacking Protection: Default OFF.
Door-Activated Anti-Carjacking: Default OFF.
Last Door Arming: Default ON.
4)
5)
Doors Lock With Last Door Arming: Default ON.
Current Sensing: Default ON.
Programmable Features
6)
7)
8)
9)
10)
11)
12)
13)
14)
Doors Lock At Ignition "On": Default ON.
Unlock Output #1 At Ignition "Off": Default ON.
Unlock Output #2 At Ignition "Off": Default OFF.
Open Door Bypass To Features #6, #7, #8: Default ON.
Lights On 5 / 30 Seconds Upon Disarm: Default 30 Seconds.
Automatic Rearming: Default ON.
2nd Channel Output Disarms System: Default ON.
.8 / 3 Second Doorlock Pulse: Default .8 Second.
Double Unlock Pulse: Default OFF.
Feature #1: Ignition-Activated Anti-Carjacking Protection
(Factory Setting: OFF)
FeatureTurnedOn:Afterturningtheignitionswitch"on"andstartingthevehicle,
youmustpresstheValetSwitchwithin60seconds.IftheValetSwitchisnotpressed
the security system will begin chirping the siren 53 seconds after the ignition was
turned"on". ThesechirpsaretoremindyouthatAnti-Carjackingisabouttoengage;
pressing the Valet Switch during the chirps will cancel the Anti-Carjacking feature.
Thechirpswilllastfor7seconds, afterwhichtimethesirenwillsoundcontinuously
and the parking lights will begin flashing to attract attention to the vehicle.
Page - 29
Page - 28
Thirty seconds after the siren and parking lights engage, or if the ignition is turned
"off", the starter interrupt will engage. Once the Anti-Carjack is engaged, the only
way to disengage it is to turn the ignition "off", then back "on" again, and then press
the Valet Switch within 5 seconds. Altogether, there are three Anti-Carjacking
Programmable Features, which may be programmed independently.
Automatic Last Door Arming feature will be interrupted. When the instant trigger
becomes ungrounded, the security system will become fully armed thirty seconds
later. All of the doors and the trunk must have the proper connection of the control
module's wiring. This feature allows unhurried passenger exit and trunk access, as
the Last Door Arming process does not start until the last door or trunk is closed,
and opening any door or the trunk will interrupt the process. You can still actively
arm the security system with the transmitter at any time.
Feature #2: Door-Activated Anti-Carjacking Protection
(Factory Setting: OFF)
Feature Turned On:This feature operates the same as the Anti-Carjacking feature
described above, except that opening a door while the ignition is "on" will initiate
the 60 second Anti-Carjacking cycle.
Feature #4 Doors Lock With Last Door Arming
(Factory Setting: ON)
Feature Turned On: When the security system passively arms from the Last Door
Armingfeature, thedoorswillalsolockifanoptionaldoorlockinterfacewasadded.
This will occur when the system becomes fully armed 30 seconds after closing the
last door. Feature #3 must be on in order for this feature to operate.
Feature #3: Last Door Arming
(Factory Setting: ON)
Feature Turned On: The security system will arm itself automatically when the
vehicle'slastdoorisclosed. Atthemomentthelastdoorisclosedthesirenwillchirp
the exterior lights will flash once, and the Status LED will flash fast. Thirty seconds
later the siren will chirp once again, the lights will flash, and the Status LED will
flash slowly, indicating that the security system is fully armed. If feature #4 is
selected, the doors will also lock at this time. If the instant trigger is grounded at any
time during the thirty second countdown (Example: opening the trunk), the
Feature #5: Current Sensing
(Factory Setting: ON)
FeatureTurnedOn: Whenthesecuritysystemisarmed,currentsensingcandetect
a positive current draw from the vehicle's battery. (Example: the dome light comes
on when a door is opened or the brake lights come on when the brake pedal is
pressed). With this feature on, the security system will trigger if a current draw is
detected.
Page - 30
Page - 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature #6: Doors Lock At Ignition "On"
(Factory Setting ON)
Feature #9: Open Door Bypass To Features #6, #7, #8 (Factory Setting ON)
Feature Turned On: When the security system locks and unlocks the doors from
Features #6, #7 and #8, if a door is open the doors will not automatically lock when
the ignition switch turns "on", or automatically unlock when the ignition switch is
turned "off".
Feature Turned On: The security system will automatically lock the vehicle's
doors one second after the ignition switch is turned "on". This feature adds
considerable personal security to you and your family.
Feature #7: Unlock Output #1 At Ignition "Off"
Feature #8: Unlock Output #2 At Ignition "Off"
(Factory Setting ON)
(Factory Setting OFF)
Feature #10: Lights On 5 / 30 Seconds Upon Disarm
(Factory Setting 30 Seconds)
Feature Turned On: Upon disarming, the exterior and interior lights will stay on
for 30 seconds, to illuminate the way to your vehicle.
Feature Turned Off: The exterior and interior lights will stay on for 5 seconds
when the system is disarmed.
These Features will cause the security system to automatically unlock either the
driver's door or all of the vehicle's doors instantly when the ignition switch is turned
"off". Please note that the exact operating parameters of these Features depends
upon the configuration of the security system and your vehicle's power doorlocks.
This system may be configured to unlock only the driver's door upon disarming.
Then if desired, pressing the large transmitter button again within 5 seconds will
unlock all of the doors. These Features can operate one of two ways: first, if all of
the doors unlock upon disarming, these Features will unlock all of the doors
when the ignition is turned "off". Second, if your vehicle is configured to unlock the
driver's door only upon disarming, these Features can be configured to unlock only
the driver's door upon the ignition being turned "off". Please consult with the
installer as to the feasibility of adding the driver's door only unlock configuration
toyourvehicle, aspowerdoorlockingsystemsdifferincompatibilitytothisfeature.
Feature #11: Automatic Rearming
(Factory Setting ON)
Feature Turned On: When the transmitter has disarmed the security system, the
system will rearm and relock the doors 90 seconds later, unless a door is opened or
the ignition is turned on. This feature prevents the system from being accidentally
disarmed if a transmitter button is unknowingly pressed by an object while in a
pocket or purse, or from children playing with the transmitter.
Page - 32
Page - 33
Feature Turned Off: When the transmitter has disarmed the security system, the
Feature #15: 3 / 45 Second Arming Delay
(Factory Setting 3 Seconds (ON)
system will stay disarmed until the transmitter is used to arm it again.
Feature Turned On: The security system will be become fully armed 3 seconds
after the arming siren chirp confirmation.
Feature #12: 2nd Channel Output Disarms System
(Factory Setting ON)
Feature Turned Off: The security system will be become fully armed 45 seconds
after the arming siren chirp confirmation.
Note: During the arming delay if any protected circuit should go into a triggered
state, the system will arm, but that circuit will be unprotected until it reverts back
to an non-triggered state.
Feature Turned On: When the 2nd channel output is utilized, the security system
will also disarm at the same time, chirping the siren twice, unlocking the doors and
turning the exterior lights on for thirty or five seconds. The 2nd channel output, and
this feature, can be used for remote trunk release operation.
Feature #13: .8 / 3 Second Doorlock Pulse
(Factory Setting .8 (ON)
Feature #16: Confirmation Chirp
(Factory Setting ON)
Feature Turned On: The doorlock outputs have a .8 second negative pulse to an
optional doorlock interface to operate the vehicle's power doorlocking system.
Feature Turned Off: The doorlock outputs have a 3 second negative pulse to an
optional doorlock interface to operate the vehicle's vacuum doorlocking system.
Feature Turned On: The security system will chirp the siren for confirmation that
the system armed and disarmed.
Feature Turned "Off": The security system will not have siren chirps for the
arming and disarming confirmation. Turning this feature off will also eliminate the
threechirpsuponarmingiftheinstanttriggercircuitisgrounded, andthefourchirps
upondisarmingifthesystemwastriggeredandreset.However,thePrewarnFeature
and the Programmable Features chirps will still operate.
Feature #14: Double Unlock Pulse
(Factory Setting OFF)
Somenewervehiclesrequireadoorlockinterfacewhichprovidesadoubledoorlock
output pulse to unlock all of the vehicle's doors. Feature #12 must be .8 second
doorlock pulse time (Feature #12 turned ON) for Feature #14 to operate.
Feature Turned On: The unlock output provides two pulses.
Regardless of this Feature, eliminating the siren chirp may be done on a onetime
temporary basis as desired by pressing the small left transmitter button twice for
arming or disarming. Even if this Feature is used to remove the confirmation chirps,
Feature Turned Off: The unlock output provides a single pulse.
the audible Automatic Transmitter VerificationTM feature will still operate.
Page - 34
Page - 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature #17: 30 / 60 Second Activated Alarm Cycle
(Factory Setting 60 Seconds (ON)
Feature Turned On: Upon activation, the siren will sound and the parking lights
will flash for 60 seconds.
Feature Turned Off: Upon activation, the siren will sound and the parking lights
will flash for 30 seconds.
Feature #19: Loud / Soft Pulsed Horn Chirps
Feature Turned On: 12 Millisecond Confirmation Honks.
Feature Turned Off: 8 Millisecond Confirmation Honks.
If your security system is configured to use the vehicle's horn, this Feature allows
a degree of compensation for the variance which is found in the length of the pulse
required to honk the horn in a satisfactory manner.
(Factory Setting Loud (ON)
Please note that the shorter 30 second activated time may be required in some
localities to comply with noise nuisance ordinances.
Feature #20: Total Closure Lock Output
Feature Turned On: 28 Second Doorlock Output.
Feature Turned Off: .8 Second Doorlock Output.
(Factory Setting OFF)
Feature #18: Pulsed Horn / Steady Siren Output
If the vehicle is so equipped, this Feature allows the installer to take advantage of
a preexisting Total Closure System.
(Factory Setting Steady Siren (OFF)
Feature Turned On: This Feature allows the use of the vehicle's horn in place of
the electronic siren for the audible output of the security system. When configured
for use with a horn, this output pulses for 10 seconds, then pauses for 5 seconds,
repeating this cycle for the duration of the activated alarm period. This prevents
the horn from overheating, thereby ensuring a maximum useful life to the vehicle
owner.
Feature Turned Off: The output is a continuous, steady output which the elec-
tronic siren requires. The siren features six different siren tones, which change
every 5 seconds.
Feature #21: Remote-Activated Anti-Carjacking Protection
(Factory Setting OFF)
Feature Turned On: Anti-Carjacking Protection Feature Activated By 3rd
Channel Output. This Feature allows remote activation of the Anti-Carjacking
Feature. If this Feature is turned ON, pressing the Small Left Button on the trans-
mitter for 3 seconds will activate the Anti-Carjacking Feature, but only when the
ignition switch is "on". This Feature may be activated regardless of the setting of
Features #1 and #2 (Ignition and Door Activated Anti-Carjacking Protection).
Page - 36
Page - 37
Feature Turned Off: 3rd Channel Will Not Operate Anti-Carjacking.
Transmitter Options
Feature #22 configured for
"Two Button Arming / Disarm-
ing" with supplied transmitter
Optional 4-button transmitter with
Feature #22 configured for "Two
Button Arming / Disarming"
Feature #22: One / Two Button Arming / Disarming
(Factory Setting One Button (ON)
Feature Turned On: One Button Arming / Disarming. This Feature controls
how the transmitter operates the security system. If this Feature is turned ON, the
transmitter's Large Center Button will alternate arming and disarming the system
with each press of the button. This type of operation is also described as a "single
button toggle" for the arming and disarming of the system.
Feature Turned Off: Two Button Arming / Disarming. Having this Feature set
to the OFF setting causes the system to operate in a "dedicated button for arming
and dedicated button for disarming" fashion. This Feature's "Two Button" setting
may be used with the standard 3-button transmitter; when configured in this fashion
the large center button arms the system, and the small right button disarms the
system. Pressing the small right button operates trunk release; pressing the large
center button and small right button together operates the 3rd channel output.
Arms system, and engages
Operates
Arms system, and
engages "panic"
with
Disarms system, and
engages "panic" with
system
"panic" with system armed
2nd channel
output
Disarms
system
disarmed
system, and
engages
"panic"
with
system
disarmed
armed
J
JJ
Operates
3rd channel
output
Operates
2nd channel
output
II
III
Operates
3rd channel
output
Enhanced "Panic" operation: Having feature #22 configured for "Two Button
Arming / Disarming" enhances the "Panic" feature's operation; using the "arm"
button activates "Panic" with an armed system, locking the doors, and using
Optional 4-button trans-
mitter for AL-1000ATV2
only; part number #105-07
AL-1000ATV2 434MHz w/Green LED (#103-03)
AL-900ATV2 302MHz w/Red LED (#109-03)
"disarm" button results in "Panic" with a disarmed system and unlocked doors.
Page - 38
Page - 39
Download from Www.Somanuals.com. All Manuals Search And Download.
L I M I T E D L I F E T I M E W A R R A N T Y
Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the Company), are
warranted to be free from defects in materials and workmanship under normal use. If a product sold by the Company
proves to be defective, the Company will repair or replace it free of charge within the first year and thereafter all
parts to be repaired will be free with only a nominal charge for Omega Research and Development, Inc.'s labor and
return shipping, to the original owner during the lifetime of the car in which it was originally installed.
All products for warranty repair must be sent postage prepaid to Omega Research & Development, Inc., P.O.
Box 508, Douglasville, Georgia 30133, with bill of sale or other dated proof of purchase. This warranty is
nontransferable and does not apply to any product damaged by accident, physical or electrical misuse or abuse,
improper installation, alteration, any use contrary to its intended function, unauthorized service, fire, flood,
lightning, or other acts of God.
This warranty limits the Company's liability to the repair or replacement of the product. The Company shall
not be responsible for removal and/or reinstallation charges, damage to or theft of the vehicle or its contents, or any
incidental or consequential damages caused by any failure or alleged failure of the product to function properly.
Under No Circumstances Should This Warranty, Or The Product Covered By It, Be Construed As A Guarantee Or
Insurance Policy Against Loss. The Company neither assumes nor authorizes any person or organization to make
any Warranties or assume any liability in connection with the sale, installation, or use of this product.
This device complies with FCC Rules part 15. Operation is subject to the following two
conditions, (1) This device may not cause harmful interference and, (2) This device must
accept any interference that may be received, including interference that may cause
undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by unautho-
rized modifications to this equipment. Such modifications could void the user's authority to
operate the equipment.
MO_AL-900/1000ATV2
Download from Www.Somanuals.com. All Manuals Search And Download.
|