EverFocus Security Camera EPD200 User Manual

EVERFOCUS  
Indoor Pendent Dome Camera  
Operation Instructions  
Model No. EPD200  
Please read this manual first for correct installation and operation. This manual should be retained  
for future reference. The information in this manual was current when published. The  
manufacturer reserves the right to revise and improve its products. All specifications are therefore  
subject to change without notice.  
PRECAUTIONS  
1. Do not install the camera near electric or magnetic fields.  
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,  
audio speakers since the magnetic fields generate from above devices will distort the video  
images.  
2. Never disassemble the camera nor put impurities in it.  
Disassembly or impurities may result in trouble or fire.  
3. Never face the camera toward the sun.  
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.  
4. Keep the power cord away from water and liquid.  
Touching the wet power cord may result in electric shock.  
5. Never install the camera in areas exposed to water, oil or gas.  
Water, oil or gas may result in failure, electric shock or fire.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATION  
Pickup Device  
Video Format  
Scanning System  
1/3" SONY Super HAD CCD  
NTSC or PAL  
NTSC: 525 TV lines, 60 fields/sec.  
PAL: 625 TV lines, 50 fields/sec.  
510 x 492 (NTSC); 500 x 582 (PAL)  
380 TVL  
Picture Elements  
Horizontal Resolution  
Sensitivity  
0.3 Lux /F=1.2  
S/N Ratio  
Electronic Shutter  
Lens  
Over 48dB(AGC Off)  
1/50(1/60)~1/100,000  
Vari-Focal or Fixed Lens  
BNC 1.0Vp-p 75ohm  
On/Off switch  
Video Output  
Back Light Comp..  
Auto Gain Control  
Flickerless  
On/Off switch  
On/Off switch  
Auto White Balance  
Auto IRIS  
Auto  
DC-Drive  
Gamma Correction  
Sync. Mode  
0.45  
Internal Sync.  
Power Source  
Two types:  
12VDC/24VAC  
12VDC only  
Power Consumption  
3W max.  
BNC output x 1  
Video Output Connector  
2.5mm Lock x 1  
AC 24V Power Connector + Video  
2.5mm x 2-pin(for DC jack)  
2.0mm x 2-pin(for BNC)  
DC 12V Power Connector + Video  
Weight  
1.25mm x 4-pin, (1BNC, DC jack)  
0.3 kg ; 0.66 lbs  
Dimension  
110mm(W)x 125(H)/ 4.33”(W) x4.92”(H)  
Pendent Tube Diameter: 26mm/1.06”  
0~50 ; 32°F~122°F (20%~80% Humidity)  
CE, FCC  
Operating Temperature  
Certifications  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIMENSION DIAGRAM  
a. Conduit Size  
26mm/1.06”  
b.  
80mm/3.15””  
125mm/4.92”  
90mm/3.54”  
110mm/4.33”  
HARDWARE OVERVIEW  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
a. Front panel design (For Vari-Focal Lens Model)  
BLC – Back Light  
Compensation  
IRIS LEVEL  
CONTROL  
AGC (Automatic  
Gain Control)  
FL(Flickerless)  
BNC Pigtail Slot for  
Focusing and  
Testing Module  
b. Front panel design (For Fixed Lens Model)  
BLC – Back Light  
Compensation  
FL(Flickerless)  
AGC (Automatic  
Gain Control)  
ES(Electronic  
Shutter)  
BNC Pigtail Slot for  
Focusing and  
Testing Module  
INSTALLATION  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
This section covers simple steps and detail installation. Please follow instruction for preventing  
any unnecessary damage.  
Simple Steps:  
1. Connect to 26mm/1.06” EMT Conduit Pipe and lock it with Hex Wrench  
2. Open camera bubble cover  
3. Connect to testing monitor(optional accessories)  
4. Adjust lens, camera position  
5. Optional adjust camera setting on Dip Switch  
1. Mount Camera  
2.5mm Hex  
Wrench  
26mm EMT  
Conduit Pipe  
Set Screws  
Camera  
a. Pre-install 26mm/1.06” EMT conduit pipe and wire video and power cables though conduit  
pipe. Connect power and video to the camera.  
b. Locking pipe with camera by tightening set screws with supplied Hex wrench.  
Note!! When connect to 12VDC with Power Extension cable . Please make sure you  
connect powr +,- correctly. Wrong connection may damage the camera.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
White (+)  
Black (-)  
2. Open Camera Bubble Cover  
Turn the camera bubble until you see the arrow face to here.  
3. Connecting to testing monitor EN220  
Connect the BNC Pigtail accessory to the front of the module for help with focusing or video  
testing.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Adjust Camera Position and Lens  
a.Adjust camera position (Tilt angle up to 90 degree): Adjust camera to the position you  
like. The turning angel is up to 90 degree. Use ‘tool-less’ screws on the side of the module  
to secure position.  
Tool-less Screws  
90 Degree  
b. Zoom and focus adjustments (For Vari-focal Lens Model)  
After the camera was installed, the zoom and focus of the lens must be adjusted.  
(1) Loosen the zoom ring knob, and then turn the ring towards <W> or <T> as necessary to  
obtain the desired view range.  
W side (Zoom out)  
The viewing range will be wider and the subject is smaller.  
T side (Zoom in)  
The viewing range will be smaller and the subject is larger.  
(2) Loosen the focus ring knob, then turn the ring towards <> or <N> as necessary to  
obtain the clear video image.  
(3) Repeat steps 1 and 2 until the best image is obtained.  
Once the lens setting finished, tighten the zoom ring and the focus ring knobs.  
CAMERA SETTING  
¾ BLC (Back Light Compensation)  
When BLC is turned on, the AGC, FL and IRIS operating point is determined by averaging over  
the center area instead of entire field-of-view, so that a dimly-lit foreground object at center area  
can be clearly distinguished from brightly-lit backgrounds. BLC should not be used unless it is  
needed to compensate for back-light.  
The default setting is OFF. For Auto-Iris lens model, the brightness can also be adjusted via the  
Iris level control VR.  
¾ AGC (Automatic Gain Control)  
AGC ON: The sensitivity increases automatically when light is low.  
AGC OFF: A-low-noise picture is obtained under a low light condition.  
The default setting is ON.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
¾ FL (Flickerless)  
When picture flicker fiercely, turn FL on, then the camera will stabilize the speed of electronic  
shutter at 1/100(S)(NTSC) or 1/120(S)(PAL) automatically, and reduce the flicker immediately.  
The default setting is OFF.  
¾IRIS Level Control (For Vari-Focal Lens Model)  
Brightness Level can be adjusted from the IRIS level VR while using the direct drive lens.  
•Turn counterclockwise to L to get darker picture.  
•Turn clockwise to H to get brighter picture.¾Electronic Shutter (For Fixed Lens Model)  
ES ON: The camera continuously adjusts the shutter speed from 1/60 (NTSC), 1/50 (PAL) second  
to 1/100,000 second according to the luminance conditions of the scene.  
ES OFF: The shutter speed is fixed at 1/60 (NTSC),1/50 (PAL) second.  
Set ES OFF, when auto iris lens is used or flicker is observed under a very bright fluorescent lamp.  
Otherwise, turn ES on for optimum performance.  
EverFocus Electronics Corp.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Europe Office:  
Head Office:  
Albert-Einstein-Strasse 1  
D-46446 Emmerich, Germany  
TEL: 49-2822-9394-0  
12F, No.79 Sec. 1 Shin-Tai Wu Road,  
Hsi-Chih, Taipei, Taiwan  
TEL: +886-2-26982334  
FAX: +886-2-26982380  
China Office:  
Room B-05D-1, KESHI PLAZA , Shangdi  
USA L.A. Office:  
Information Industry Base,  
Haidian District, Beijing China 100085  
TEL: +86-10-62973336/37/38/39  
1801 Highland Ave. Unit A  
Duarte, CA 91010, U.S.A.  
TEL: +1-626-844-8888  
FAX: +1-626-844-8838  
FAX: +86-10-62971423  
Japan Office:  
USA N.Y. Office:  
1809 WBG MARIBU East 18F,  
2-6 Nakase.Mihama-ku.  
Chiba city 261-7118, Japan  
TEL: +81-43-212-8188  
FAX: +81-43-297-0081  
415 Oser Avenue Unit S  
Hauppauge, NY 11788  
TEL: 631-436-5070  
FAX: 631-436-5027  
Your EverFocus product is designed and  
manufactured with high quality materials and  
components which can be recycled and  
reused.  
Ihr EverFocus Produkt wurde entwickelt und  
hergestellt mit qualitativ hochwertigen  
Materialien und Komponenten, die recycelt  
und wieder verwendet werden können.  
Dieses Symbol bedeutet, dass elektrische und  
elektronische Geräte am Ende ihrer  
Nutzungsdauer vom Hausmüll getrennt  
entsorgt werden sollen.  
This symbol means that electrical and  
electronic equipment, at their end-of-life,  
should be disposed of separately from your  
household waste.  
Please, dispose of this equipment at your  
local community waste collection/recycling  
centre.  
Bitte entsorgen Sie dieses Gerät bei Ihrer  
örtlichen kommunalen Sammelstelle oder im  
Recycling Centre.  
Helfen Sie uns bitte, die Umwelt zu erhalten, in  
der wir leben!  
In the European Union there are separate  
collection systems for used electrical and  
electronic product.  
Please, help us to conserve the environment  
we live in!  
P/N: MEFDG00400  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  

Esoteric CD Player X 03 User Manual
FEIN Power Tools Trimmer BLs 25 User Manual
FoodSaver Food Saver V2860 User Manual
Fostex Speaker FW168HP X User Manual
Frigidaire Air Conditioner FRA09EPT1 User Manual
GE Answering Machine UF 4000 User Manual
GE Clothes Dryer WBVH5100H User Manual
GE Dishwasher 712M User Manual
Gianni Industries Door L GL600 User Manual
Gitzo Camcorder Accessories GT5530S User Manual