D00864200A
DVD/DVD-A/SACD/CD Player
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
This product has been designed and manufactured according to
FDA regulations “title 21, CFR, chapter 1, subchapter J, based on
the Radiation Control for Health and Safety Act of 1968“, and is
classified as class 1 laser product. There is not hazardous invisible
laser radiation during operation because invisible laser radiation
emitted inside of this product is completely confined in the
protective housings.
WARNING : TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
The label required in this regulation is shown ①.
< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO
EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS
ARE WITHIN!
① For U.S.A.
< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,
CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE
PRODUCT UNTIL IT HAS BEEN REPAIRED.
< USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
For U.S.A.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
Optical pickup :
Type
: SLD6163RL-G
Manufacturer : SONY CORPORATION
Laser output : Less than 1mW on the objective lens
Wavelength : 785 15 nm (CD), 655 10 nm (DVD)
• Reorient or relocate the equipment and/or the receiving
antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
VARING: APPARATEN INNEHÅLLER LASER KOMPONENT MED
STRÅLNING ÖVERSTIGANDE KLASS 1.
“ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING NAR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ
UDSAETTELSE FOR STRÅLING”
• Consult the dealer or an experienced radio/TV technician
for help.
CAUTION
“VAROITUS! SUOJAKOTELOA EI SAA AVATA. LAITE SISÄLTÄÄ
LASERDIODIN. JOKA LÄHETTÄ (NÄKYMÄTÖNTÄ) SILMILLE
VAARALLISTA LASERSÄTEILYÄ”.
Changes or modifications to this equipments not expressly
approved by TEAC CORPORATION for compliance will void the
user’s warranty.
ADVARSEL: USYNLIG LASERBESTRÅLING NÅR DENNE DELEN ER
ÅPEN OG SIKKERHETSSPERREN ER UTKOBLET UNNGÅ
UTSETTELSE FOR STRÅLING.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Thank you for choosing Esoteric. Read this manual carefully to get the best performance from this unit.
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connection to a TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connections to an amplifier, etc. . . . . . . . . . . . . . . . . . . . . . . 12
Front panel features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Front panel display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Understanding the remote control unit . . . . . . . . . . . . . . . . . . 16
Digital output formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Test tone length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Speaker levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
S-Video output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TV screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Still mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Component video output . . . . . . . . . . . . . . . . . . . . . . . . . 39
PAL-NTSC conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Closed captioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
On-screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Angle indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Background color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Parental Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Selecting a chapter or track. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Skipping playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Selecting the playback area. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Selecting groups and titles . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Repeat mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Fast scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Programmed playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing camera angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Selecting audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Slow motion/frame advance . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Display dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Lip sync. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Selecting subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DVI output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Clock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Analog sound output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Turning video on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Changing the display mode . . . . . . . . . . . . . . . . . . . . . . . . . . 28
i.LINK (AUDIO) output setting . . . . . . . . . . . . . . . . . . . . . . . . . 42
i.LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Settings (introduction). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
CD playback mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Digital output settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Analog output settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Audio DRC (Dynamic Range Controlling) . . . . . . . . . . . . . . 32
Downmix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Group playback mode (DVD audio) . . . . . . . . . . . . . . . . . . 32
Progressive scan setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Video adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
On-screen display language . . . . . . . . . . . . . . . . . . . . . . . . 34
Displaying subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Subtitle language selection. . . . . . . . . . . . . . . . . . . . . . . . . 34
Audio language selection . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Speaker setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
VRDS mechanism for DVD and SACD players,
Unsurpassed design and features
incorporating a duralumin turntable and a
SS400 bridge
Separation of power supplies for each major function (digital
audio, DAC circuitry, analog audio) ensures total fidelity. The
DACs for video and audio have sub-ground impedances with
exceptional S/N figures. DTS 96/24 decoder, as well as Dolby
Digital and DTS decoders are incorporated. Full 5.1 surround
playback, including DVD audio and SACD playback is possible
with the UX-3.
The VDRS mechanism completely eliminates any vibration
caused by the disc itself, thanks to the full-diameter clamp
that clamps the disc securely to the turntable. Additionally,
warping and other defects of the disc are eliminated. The
constancy of the reading angle between the optical pickup
and the disc pits is therefore increased, and read errors,
together with the occurrence of timing errors to the clock
circuit, are significantly reduced.
A lip sync control allows precise synchronization between
picture and audio.
Playback of DVD/SACD discs requires high-speed rotation and
a high degree of precision, and the UX-3 accordingly uses a
duralumin turntable. The bridge employs a pair of precisely
engineered ball bearings, and is constructed of 10mm thick
SS400 steel.
Audio DACs
All audio channels use Burr-Brown 24-bit DA converters
(PCM1704). Improved linearity is achieved for the two front
channels by the use of dual converters for each channel.
The audio DAC boards employ a high-quality quartz crystal,
resulting in the almost complete elimination of jitter and
subsequent distortion-free DA conversion.
Coreless motor with neodymium magnets
A newly developed three-phase brushless spindle motor
provides the fast and accurate turntable rotation required for
DVD and SACD playback. This, coupled with the clamping
turntable and the precision ball bearings, eliminate irregular
rotation and vibration.
Super high-precision video output
The UX-3 uses the 14-bit 216MHz video DAC from Analog
Devices; the ADV7314. This provides 16x oversampling on
interlace playback and 8x oversampling on progressive-scan
playback. Noise is therefore shifted to unwanted regions, and
an outstandingly clear picture results. In the progressive-scan
mode, smoothing is achieved using DCDi chips from Faroudja.
Neodymium stabilizes the motor’s driving current, reducing
influence on the audio sections of the unit.
Constant-angle optical pickup mounted on a
sled with feedback-monitored speed control
NTSC and PAL playback and progressive-scan
By mounting the pickup on a sled whose axis is rigid, the
pickup lens is maintained at a constant angle and the laser
beam, and hence the optical axis, is maintained in an accurate
vertical orientation. An Esoteric original three-phase brushless
motor with hall element detection drives the sled, and the
speed of the sled is monitored and used to control the sled
itself in a servo feedback operation, meaning the sled is highly
responsive and smooth in its operation.
Both PAL and NTSC discs can be played back and conversion
between the standards is possible, allowing the same monitor
and player to be used for discs produced to either standard.
Progressive-scan playback (with the appropriate television or
monitor) allows the best possible picture quality, even with
large screens.
Word synchronization
Sturdy, rigid chassis with triple-point
pinpoint foot support
A master word clock from a high-quality DA converter or
master clock generator can be used for clock synchronization,
resulting in the almost complete elimination of jitter.
Using a high-quality clock signal provided by an external DA
converter such as the Esoteric G-0/G-0s provides optimum
video and audio quality, up to 192kHz, optimizing a top
ranking universal player like the UX-3.
The unit is constructed with a 5mm thick robust steel base
plate, and is divided into three logical sections, thereby
reducing interference between components of the unit.
Highly rigid mounts are used for the VDRS disc mechanism.
To eliminate vibration, three solid (tool steel) feet support the
unit and isolate it mechanically.
i.LINK (AUDIO) terminal
Brushed aluminum finish exemplifies the
quality of construction
In addition to the digital audio from DVD-Video, CD and
video CD, the digital surround audio from SACD and DVD-
Audio discs can be output from the i.LINK (AUDIO) terminal.
The front panel is constructed of thick brushed aluminum.
The high-quality luxurious finish matches the overall attention
to the finest possible quality, shown in such details as the
illuminated periphery to the control buttons, the top-panel
logo, and the milled aluminum disc tray.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Use
DO NOT MOVE THE UNIT DURING PLAYBACK
What’s in the box
Please confirm that the following accessories are in the box
when you open it.
During playback, the disc rotates at high speed. Do NOT lift or
move the unit during playback. Doing so may damage the
disc or the unit.
Remote control unit x 1
Batteries (AA, R6, SUM-3) x 2
Screwdriver x 1
Felt sheet x 3
Power cord x 1
WHEN MOVING THIS UNIT
When changing places of installation or packing the unit for
moving, be sure to remove the disc and return the disc tray to
its closed position in the player. Then, press the power switch
to turn the power off, and disconnect the power cord.
Moving this unit with the disc loaded may result in damage to
this unit.
Owner’s manual x 1
Warranty card x 1
Conventions about This Manual
< Instructions in this manual describe the controls on the
remote control. You can also use the buttons on the front
panel if they have the same or similar names as those on the
remote.
< The types of functions and operations that can be used for a
particular disc vary depending on the features of that disc. In
some cases, these functions and operations may differ from
the descriptions given in this Owner’s Manual. In this event,
follow the instructions given on the screen. This Owner’s
Manual only covers basic disc operations.
Placement of the unit
High-quality hardened tool steel is used for the pin-point feet,
securely attached to the bottom of the player. Although the
cover feet may appear loose, the weight of the unit causes
them to be firm and secure, and the design effectively damps
and reduces vibration.
< Be careful to avoid injury when moving the unit, on account
of its weight. Get someone to help you if necessary.
< For some operations, the PROHIBIT icon “A” may appear on
the screen. This indicates that the operation described in this
Operations Manual is not permitted for the current disc.
< The drawings about the TV screen and front panel display
used in this Operations Manual are purely for the purposes of
explanation. The actual displays may differ slightly from what
are shown here.
< To protect easily scratched furniture, you may stick the felt
supplied with the unit to the bottom of the cover feet.
Pin-point foot
Bottom plate
of the unit
Steel foot
Read this before operation
< As the unit may become warm during operation, always leave
sufficient space around the unit for ventilation.
< The voltage supplied to the unit should match the voltage as
printed on the rear panel. If you are in any doubt regarding
this matter, consult an electrician.
Cover foot
Cover foot retaining screws
< Choose the installation location of your unit carefully. Avoid
placing it in direct sunlight or close to a source of heat. Also
avoid locations subject to vibrations and excessive dust, heat,
cold or moisture.
< Do not place the unit on the amplifier/receiver.
< Do not open the cabinet as this might result in damage to the
circuitry or electrical shock. If a foreign object should get into
the unit, contact your dealer or service company.
< When removing the power plug from the wall outlet, always
pull directly on the plug, never yank the cord.
CAUTION
The product shall not be exposed to dripping or splashing and
that no object filled with liquids, such as vases, shall be placed
on the product.
Do not install this equipment in a confined space such as a
book case or similar unit.
< To keep the laser pickup clean, do not touch it, and always
close the disc tray.
< Do not attempt to clean the unit with chemical solvents as
this might damage the finish. Use a clean, dry cloth.
< Keep this manual in a safe place for future reference.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Restoring factory settings
“DTS” and “DTS 96/24” are trademarks of Digital Theater
Systems, Inc.
If you have made a lot of changes to the setup, and want to
restart from a known set of options, restore the unit to the
factory settings as follows:
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
“Super Audio CD” is a registered trademark.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only, unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
1. With the unit turned off, press and hold down the STOP
button.
2. While holding down the STOP button, press the POWER
switch.
The UX-3 player uses six DACs with high-quality 14-bit
216MHz processing for video output. This type of DAC, the
ADV7314, employs new Noise shaping Video (NSV)
technology from Analog Devices, Inc. of the USA.
All memories are erased, and the unit returns to the factory
settings.
NSV technology uses multi-bit delta-sigma conversion,
removing video noise and providing low noise and high
linearity, without the loss of information that is often
associated with analog filtering systems.
Noise Shaped Video and NSV are registered trademarks of
Analog Devices, Inc.
Changing the Color System (NTSC/PAL)
If you experience picture distortion or are unable to view the
monitor image, you may need to change the color setting to
match your TV.
To eliminate “jaggies” and produce clear natural images, the
UX-3 uses DCDi (Directional Correlational Deinterlacing)
technology. The circuits employed are from the Faroudja
business devision of Genesis Microchip, and enable hardware
based diagonal line detection and smoothing from a pixel
based image. As a result, smoother progressive-scan images
can be produced, with “jaggie” noise reduced by interpolation
techniques.
1. Turn the unit off.
2. While holding down the PAUSE button of the main unit, press
the POWER switch.
3. While “V Set NTSC” (or “V Set PAL”) is displayed on the front
panel display, press the / button.
The display changes to “V Set PAL” (or “V Set NTSC”).
Select “V Set PAL” when a PAL TV (European standard) is
connected. Select “V Set NTSC” when a NTSC TV (American
standard) is connected.
4. Press the POWER switch to turn the unit off.
Note that you have to turn the unit off before each change.
About MOD.(Modulation) PAL:
Most models of the newly developed countdown PAL TV
system detect 50 Hz (PAL)/60 Hz (NTSC) and automatically
switch vertical amplitude, resulting in a display without
vertical shrinkage.
If your PAL TV does not have a V-Hold control, you may not
be able to view NTSC disc because the picture may roll. If the
TV has a V-Hold control, adjust it until the picture stops
rolling. On some TVs, the picture may shrink vertically, leaving
black bands at the top and bottom of the screen. This is not a
malfunction; it is caused by the NTSC-PAL conversion.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Discs
Region Number of DVD Video discs:
Type of Discs That Can be Played on This
System
DVD players and discs are designed with region numbers that
dictate the regions in which a disc can be played. If the region
number on the disc you want to play does not match the region
number of your DVD player, you will not be able to play the disc.
In that case, an error message will appear on the screen.
This player can playback discs bearing any of the following logos:
DVD Video:
• Single-sided or double-sided discs
• Single layer or dual layer discs
• Dolby Digital, DTS, MPEG or Linear PCM
digital audio
The region number is printed on the rear panel of this unit.
• MPEG-2 digital video
U.S.A./Canada model
Europe model
Korea model
• This unit can play DVD-R discs recorded in
DVD video format.
• This unit can play DVD-RW discs recorded in
DVD video format or DVD video recording
format.
About DVD-RW
< DVD-RW discs that were recorded with copy-once only
permission cannot be played.
Discs are generally divided into one or more titles.
Titles may be further subdivided into chapters.
< When playing a DVD-RW disc that was edited on a DVD
recorder, the screen may momentarily black out at the edited
point.
DVD Audio:
• Single sided discs
• Single layer or dual layer discs
< When playing a DVD-RW disc that was edited on a DVD
recorder, you may see scenes from just before the edited
point.
• Linear or packed PCM digital audio
• Some discs may contain MPEG-2 video, and
Dolby Digital, DTS or MPEG digital audio.
Discs are generally divided into one or more
groups. Groups may be further subdivided into
tracks.
About CD-R/CD-RW
CD-R/RW discs recorded in Audio CD format and finalized
correctly are playable. But depending on the quality of the
disc and/or the condition of the recording, some CD-R & CD-
RW discs may not be playable.
Audio CD:
• 12cm or 8cm discs
• Linear PCM digital audio
Audio CDs are divided into tracks.
Caution:
< If you record a disc using a personal computer, even if it is
recorded in a compatible format, there are cases in which it
may not play because of the settings of the application
software used to create the disc. (Check with the software
publisher for more detailed information.)
Video CD:
• 12cm or 8cm discs
• MPEG-1 digital audio
• MPEG-1 digital video
Video CDs are divided into tracks.
< Unfinalized CD-R/CD-RW/DVD-R/RW discs cannot be played.
SACD:
• Single layer, dual layer or Hybrid layer
• 12cm or 8cm discs
• Digital audio (DSD)
SACDs are divided into tracks.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
< Always place the disc on the disc tray with the label side up.
(Compact discs can be played or recorded only on one side.)
< To remove a disc from its storage case, press down on the
center of the case and lift the disc out, holding it carefully by
the edges.
Following discs cannot be played with this
unit:
• CD-G, Data part of CD-EXTRA, PHOTO CD, CD-ROM and
DVD-ROM discs
• discs recorded in a color system other than PAL or NTSC
• illegally produced discs
• scratched or damaged discs
• discs that are dusty, soiled or marked with fingerprints
Warning:
How to remove the disc
How to hold the disc
If you attempt to play back such discs, there is a risk that sudden
loud noise can blast over the speakers at full volume and cause
damage to the speakers and your hearing.
< Should the disc become dirty, wipe the surface radially (from
the center hole outward towards the outer edge) with a soft,
dry cloth:
Copy-protected discs and other discs that do not conform to the
CD standard may not play back correctly in this player. If you use
such discs in this unit, TEAC ESOTERIC COMPANY cannot be
responsible for any consequences or guarantee the quality of
reproduction. If you experience problems with such non-
standard discs, you should contact the producers of the disc.
< Never use such chemicals as record sprays, antistatic sprays or
fluid, benzine or thinner to clean the discs. Such chemicals
will do irreparable damage to the disc’s plastic surface.
< Discs should be returned to their cases after use to avoid dust
and scratches that could cause the laser pickup to “skip.”
< Do not expose discs to direct sunlight or high humidity and
temperature for extended periods. Long exposure to high
temperatures will warp the disc.
< Do not play any disc that is warped, deformed or damaged.
Playing such discs may cause irreparable harm to the playing
mechanisms.
< CD-R and CD-RW discs are more sensitive to the effects of
heat and ultraviolet rays than ordinary CDs. It is important
that they are not stored in a location where direct sunlight
will fall on them, and which is away from sources of heat
such as radiators or heat-generating electrical devices.
< Printable CD-R and CD-RW discs aren’t recommended, as the
label side might be sticky and damage the unit.
Example of Icons used on DVD discs:
number of audio tracks recorded on the disc
number of subtitles recorded on the disc
screen aspect ratio
disc recorded with multiple camera angles
region code
< Do not stick papers or protective sheets on the discs and do
not use any protective coating spray.
< Use a soft oil-based felt-tipped pen to write the information
on the label side. Never use a ball-point or hard-tipped pen,
as this may cause damage to the recorded side.
< Never use a stabilizer. Using commercially available CD
stabilizers with this unit will damage the mechanisms and
cause them to malfunction.
< Do not use irregular shape CDs (octagonal, heart shaped,
business card size, etc.). CDs of this sort can damage the unit:
< If you are in any doubt as to the care and handling of a CD-
R/CD-RW disc, read the precautions supplied with the disc, or
contact the disc manufacturer directly.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to a TV
CAUTION:
< Switch off the power to all equipment before making connections.
< Read the instructions of each component you intend to use with this unit.
< Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the
signal interconnection cables together with the AC power cord or speaker cables.
C
B D E
A
If you are not using an
audio amplifier, connect
the L and R analog audio
outputs to the appropriate
audio inputs of the
television.
Only use one method of video connection
(note that the BNC component method
uses three cables).
R
L
Y
PB
PR
AUDIO IN
COMPONENT
VIDEO IN
VIDEO
IN
S-VIDEO
IN
D1/D2
DVI-D IN
(HDCP)
TV (Monitor)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
< Adjust the video aspect ratio to match that of the television
(see page 38) .
C
Component video output terminals
Use commercially available BNC coaxial cables to connect
the unit to the component video inputs of a suitably
equipped television or monitor to enjoy a high-quality
picture. Use these terminals in preference to S-Video or
composite video connections.
< If the component video terminals or the D1/D2 terminal are
used to connect the unit to a television with progressive
scan capabilities, the output can be set to match this (see
page 39).
< Note that these terminals cannot be connected to high
definition component (Y/PB/PR) terminals.
< This unit adopts analog copy protection features. If the unit
is connected to a TV through a VCR (video cassette
recorder), the resulting playback may be affected. Connect
the unit directly to the television.
< If the television or monitor is equipped only with RCA (pin)
jacks for component video, a suitable adaptor cable or
adaptors should be used.
< In all cases, use the highest quality cables for the best
possible picture.
D
S-Video output terminal
Use a commercially available S-Video cable to connect the
unit to the S-Video input of a suitably equipped television or
monitor. Use this connection in preference to a composite
video connection.
A
DVI-D video output terminal
Use a commercially available DVI-D output cable to connect
the unit to a DVI/HDCP compatible television or monitor.
DVI output formats
480p (NTSC) or 576p (PAL), 720p, 1080i
E
Composite video output terminal
< The television connected in this way must be DVI/HDCP
compatible. Use with incompatible televisions may
sometimes result in the playback picture not being visible.
Use a commercially available RCA (pin) video cable to
connect the unit to the composite video connector of a
television or monitor. Use this connection only if no other
video connection method is available.
< See page 26 for further details on DVI output formats.
< Make sure that you read and understand the documentation
provided with the DVI component, as well as this unit’s
documentation.
B
D1/D2 video output terminals (component)
By using a commercially available D terminal cable to
connect the unit to a “D compatible” (D1, D2, D3 or D4)
television or monitor, high-quality images, equivalent to
those achieved using component video, will be displayed.
< D terminal cable is not available in all countries.
D terminal and signal format (NTSC/PAL)
480i/576i
480p/576p
(525i/625i)
(525p/625p)
D1 terminal
D2 terminal
D3 terminal
D4 terminal
X
Numbers in parentheses show the number of scan lines
i = interlace (flyback)
p = progressive scan
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections to an amplifier, etc.
CAUTION:
< Switch off the power to all equipment before making connections.
< Read the instructions of each component you intend to use with this unit.
< Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the
signal interconnection cables together with the AC power cord or speaker cables.
Stereo amplifier
AUDIO IN
Decoder-equipped amplifier
DIGITAL IN
(COAXIAL)
R
L
R
L
Balanced XLR
pin assignment
F
G
I
G
J
K
H
WORD SYNC OUT
DIGITAL IN
(OPTICAL)
i.LINK(AUDIO)
(IEEE1394)
Wall socket
Digital audio device
(CD recorder, MD deck, etc.)
Master clock generator
(G-0s, etc.)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
F
I
Analog audio output terminals
Word sync connector
Use either the XLR or RCA (pin) terminals for analog stereo
output.
This allows the use of an externally-generated word clock
connection, using a commercially available BNC coaxial
cable.
XLR: Use balanced XLR audio cable
RCA: Use RCA (pin) audio cable
Devices producing such a suitable clock signal include
external D-A converters or dedicated word clock generators.
Connect the SYNC OUT (or WORD OUT) of such a device to
the unit.
< When using these terminals, set “Analog Output” to “2 ch”
(or select “2 ch” using the 2CH/MULTI button of the remote
control unit) to downmix the multi-channel material to two
channels.
Note that if “Analog Output” is set to “Multi ch”, only the
front L/R sound of the multi-channel material will be output
from these terminals.
J
SIGNAL GND connection
Use a commercially available PVC-covered cord to connect
the signal ground terminal on the unit to the amplifier signal
ground.
< Note that this is NOT an electrical safety ground (earth).
G
Digital audio output terminals
Digital audio from DVD-Video, CD and video CD is output
from these terminals.
The unit may be connected using either coaxial or optical
(TOS) commercially available cables to amplifiers including a
decoder, or to digital audio devices such as CD recorders,
etc.
K
Power cord receptacle
After all other connections have been made, insert the
supplied AC power cord into this receptacle, then connect
the other end of the power cord into the wall socket. Ensure
that your AC voltage corresponds to the voltage marked on
the rear panel of the unit. Consult a qualified electrician if
you are in doubt.
COAXIAL: Use RCA (pin) digital audio cable
OPTICAL: Use optical digital audio cable (TOS)
< In order to avoid the risk of electric shock, fire, and so on,
only use the supplied power cord.
< If you are not going to use the unit for some time,
disconnect the power cord from the wall socket.
< The optical terminal is covered by a shutter. Make sure that
the cable is firmly inserted, but do not force the cable when
connecting it or removing it, in order not to cause damage
to the unit.
H
i.LINK (AUDIO) terminal
In addition to the digital audio from DVD-Video, CD and
video CD, the digital surround audio from SACD and DVD-
Audio discs can be output from this terminal.
Use a commercially available S400 compatible i.LINK
(IEEE1394) 6pin cable to connect the unit to an amplifier.
< When using this terminal, set the i.LINK output setting to
“i.60958” or “i.PCM” (see page 42).
< See page 43 for further details on i.LINK.
< To enjoy surround sound from a DVD Video disc, connect
the DIGITAL OUT terminal or the i.LINK (AUDIO) terminal to
an amplifier with Dolby Digital/DTS/MPEG decoder.
< To enjoy surround sound from a DVD Audio and SACD
disc, connect the i.LINK (AUDIO) terminal to a suitably
equipped surround sound amplifier.
< DVD Audio disc signals are converted where necessary from
192kHz or 176.4kHz to 96kHz/88.2kHz or 48kHz/44.1kHz.
However, there may be some occasions when digital audio
cannot be output by the unit from such a disc.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel features
A
B
C
D
E
F G
H
I
J
A
POWER
Use this to turn the unit on and off. When the unit is on, the ring surrounding the
button lights up.
The equipment draws nominal non-operating power from the AC outlet with its
POWER switch in the OFF position.
B
C
CLOCK MODE
Use this to select an external word sync source connected to the WORD SYNC
connector on the rear panel.
Also use this to select the 4% DOWN mode.
Remote control sensor
Receives signals from the remote control unit. Point the remote control unit at this
sensor when operating the remote control unit.
D
E
F
Display
Disc tray
OPEN/CLOSE
Use this to open and close the disc tray.
G
STOP
Use this to stop playback. When playback is stopped, the ring surrounding the
button lights up.
Also use this to change the i.LINK output setting.
H
I
PLAY
Use this to start playback. When a disc is being played back, the ring surrounding
the button lights up.
PAUSE
Use this to pause playback. When playback is temporarily paused, the ring
surrounding this button lights up.
J
SKIP (.//)
Use these for skip operations. Pressing and holding these buttons for more than a
second changes the scanning speed.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel display
g
e
a
q
c
i
b
d
f
h
p
j
s
n
o
m
r
l
k
a
b
m
n
Disc type indicator
GUI indicator
Shows the type of disc currently loaded.
Lights to show that the GUI is being displayed through the
video outputs.
GROUP indicator
Message area
Indicates that the group number of a DVD audio disc is being
shown.
Alphanumeric display to show times, titles, status messages,
etc.
c
d
e
TITLE indicator
o
p
REPEAT indicator
Indicates that the title of a DVD disc is being shown.
Lights when repeat play is selected
CHAPTER indicator
Angle indicator
Indicates that the chapter of a DVD disc is being shown.
Lights when an alternative angle is available on the section of
the disc being played back.
TRACK indicator
Indicates that the track number of a CD, SACD or video CD is
being shown.
q
Pause indicator
Lights when playback is paused.
f TOTAL indicator
r
Playback indicator
Indicates that the total time is being shown.
Lights when playing back.
g
REMAIN indicator
s
PROGRESSIVE indicator
Indicates that the remaining time is being shown.
Lights when progressive-scan video output is enabled.
h
i
DOLBY DIGITAL indicator
Lights to show that Dolby Digital audio is being played back.
DTS indicator
Lights to show that DTS audio is being played back.
j
DOWN MIX indicator
Lights to show that a multi-channel source has been
downmixed to 2 channels.
k
l
5.1CH indicator
Lights when the Analog Out setting is set to “Multi Channel”.
Channel indicators
Light to show which surround channels are currently in use.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding the remote control unit
A
B
C
D
Number buttons
Use these for selecting tracks by number, etc.
DVI ON/OFF
Use this to turn DVI video output on and off.
VIDEO ON/OFF
Use this to turn all video on and off.
2CH/MULTI
Use this to switch between two-channel (stereo) and multi-
channel surround audio output.
E
PLAY AREA
Use this with DVD audio and SACD discs to select the
playback area.
O
A
F
G
H
I
SLOW (
/
)
Use these for slow motion video playback.
P
Q
S
SCAN (m/,)
B
Use these for fast scanning during playback.
C
E
R
T
D
STOP
F
G
H
U
V
Equivalent to pushing the STOP button on the front panel.
PLAY
W
I
Equivalent to pushing the PLAY button on the front panel.
X
J
J
MENU
K
Use this button with menu-enabled DVD discs to bring up the
DVD menu.
Y
a
L
K
L
Cursor buttons and ENTER
M
Z
N
Use these cursor buttons for navigation of on-screen menus
and the ENTER button to confirm selections.
SETUP
Use this button to enter the main menu where you can set up
the parameters of the unit.
M
N
AUDIO
Use this to select the audio for playback.
LIP SYNC
Use this to synchronize video and audio when playing back
DVDs.
O
P
OPEN/CLOSE button
Duplicates the functions of the OPEN/CLOSE button on the
front panel.
Clear button
Use this button to clear entry errors, etc.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
R
DISPLAY
How to insert the batteries
Use this button to change the display mode.
Remove the cover of the remote control unit with a
screwdriver. After checking the polarity (+/_) of two AA
batteries, insert the batteries, replace the cover and replace
the screws.
FL DIMMER button
Use this button to change the brightness of the front panel
display.
S
T
REPEAT
Use this button to set the repeat playback mode.
PROGRAM
Use this button when programming playback order.
U
GROUP/TITLE
Use these buttons to skip back or forward by one group or
title.
V
SKIP (.//)
These buttons are equivalent to the skip buttons on the front
panel.
Battery Replacement
If the distance required between the remote control unit and
main unit decreases, the batteries are exhausted. In this case
replace the batteries with new ones.
W
PAUSE
This button is equivalent to the PAUSE button on the front
panel.
Precautions concerning batteries
X
Y
TOP MENU
< Be sure to insert the batteries with correct positive “+” and
negative “_” polarities.
< Use batteries of the same type. Never use different types of
batteries together.
Use this button to return control to the top menu of a DVD.
RETURN
Use this button to go up a level in menu systems. When
playing back video CDs, use it to return to the top menu.
< Rechargeable or non-rechargeable batteries can be used but
not mixed together. Refer to the precautions on their labels.
< When the remote control unit is not to be used for a long
time (more than a month), remove the batteries from the
remote control unit to prevent them from leaking. If they
leak, wipe away the liquid inside the battery compartment
and replace the batteries with new ones.
Z
a
SUBTITLE
Use this button to select the displayed subtitles during DVD
playback.
< Do not heat or disassemble batteries and never dispose of old
batteries by throwing them in a fire.
ANGLE
Use this button to select camera angles during DVD playback.
Notes on use
< Point the remote control unit at the player’s remote sensor
within seven meters (23 feet) of the player. There should not
be any obstacles between the player and the remote control
unit.
< Do not allow direct sun or other light to shine on the remote
sensor part of the player. This may cause the remote control
unit to work incorrectly.
< Note that other units with remote controls may operate
incorrectly because of infrared light “overspill” when you
operate this remote control unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VCD CD SACD DVD-A
Playback
5
Press the PLAY button to start playback if playback has
not started automatically.
3
2 4
1
5
If a menu is shown on screen (some DVD or video discs may
show such a menu), see the next section.
1
Turn on the power using the POWER button on the
main unit.
On-screen menu
An on-screen menu is shown when a DVD or video CD with
playback control (PBC) content is loaded.
The way in which the menu works may differ from disc to
disc.
The button and the display light.
2
Press the OPEN/CLOSE button.
DVD menus
Use the cursor buttons to select the menu item from a DVD,
and confirm the selection using the ENTER button.
The tray opens after a second or two (this delay is due to the
movement of the internal mechanism of the unit before
opening).
3
Insert the disc label side up.
Returning to the menu screen
Press either the MENU button or (to return to the top menu)
the TOP MENU button.
MENU
TOP MENU
< In the case of double-sided discs, the side to be played should
be face down.
< Make sure the disc is centered in the tray in order to avoid
any malfunction or jamming of the tray or damage to the
disc.
< Depending on the disc, pressing MENU or TOP MENU during
playback may restart playback from the first chapter.
< This function is not available with a DVD-RW disc with VR
content.
4
Press the OPEN/CLOSE button again.
The tray will close. Take care not to trap your fingers in the
tray.
The unit reads the disc (this may take a little time) and the
display shows “LOADING”. Some discs may automatically
start playback.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback control (with PBC enabled) video CDs
Stopping playback
With these discs, the number buttons can sometimes be used
to select menu items.
Press the STOP button (the ring surrounding the STOP button
on the main unit lights).
Jump between pages of multi-page menus (on some video
CDs) with the SKIP buttons (.//).
With a video DVD or video CD, the unit enters resume mode
(see the next section). Pressing STOP once again stops
playback completely.
< Pressing RETURN during playback returns to the menu of a
PBC video CD.
< Note that the DISPLAY, REPEAT and PROGRAM buttons do
not work during PBC playback.
Resume mode
Playback without PBC
In the stop mode press the number buttons or SKIP buttons
(.//) and PLAY button to playback video CDs without
using the PBC facility.
DVD audio discs with picture stills
Use the SLOW buttons (
/
) to change between still
images that are shown when some DVD audio discs are
played back.
When the STOP button is pressed with a video DVD or video
CD, playback is stopped, and the display shows “RESUME”.
Pressing PLAY continues playback.
Pressing any of the following buttons cancels resume mode:
STOP, OPEN/CLOSE, POWER.
Opening and closing the tray
Pausing playback (freezing the picture)
Pressing OPEN/CLOSE opens the tray if it is closed, and closes
it if it is open. When the tray is opened during playback, it
may take a few seconds before the disc is “unloaded” and
the tray opens.
Press the PAUSE button to pause audio playback (the ring
surrounding the PAUSE button on the main unit lights). Any
DVD or video CD image is frozen.
Press PLAY or PAUSE to restart playback.
< If the still picture appears blurred or noisy, reconfigure the still
mode to “field” (see page 39).
< Caution - do not leave player in the “pause” mode for
extended periods of time. Damage to your television or the
player may occur.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD DVD-A
DVD VCD CD SACD DVD-A
Selecting groups and titles
Selecting a chapter or track
Use the number button to select tracks or chapters for
playback. Use the +10 button to enter the first digit of
numbers greater than 9 (repeated presses show 1-, 2-, 3- etc.)
and the single digit buttons (0 through 9) for the second
digit, or single-digit track numbers.
Use the remote control unit’s GROUP/TITLE buttons (
to change titles and groups on DVD media.
/
)
If pressed during playback, these buttons start playback at the
selected group/title. If pressed during pause or stop mode,
playback is paused at the start of the selected group/title.
Note that some discs may start playback when a group or title
is selected, regardless of the pause or stop status.
CD (including video CD and SACD) playback starts from the
selected track, regardless of whether the number is selected
during playback or playback is stopped or paused.
DVD playback starts from the selected chapter or track if
selection is made during playback or stop. It pauses at the
start of the selected track if the selection was made from
pause mode. In stop mode, only chapters from the first title
can be selected.
DVD VCD CD SACD DVD-A
Skipping playback
Use the CLEAR button to clear mistaken entries.
SACD DVD-A
Selecting the playback area
Press the SKIP button (. or /) repeatedly until the
desired chapter or track is found. The selected chapter or
track will be played from the beginning.
< If the . button is pressed once during playback, playback
returns to the start of the current track or chapter. If it is
pressed within one second from the start of the track,
playback returns to the start of the previous track or chapter
(so pressing the button twice in quick succession will skip
back two tracks, etc.).
When playback is stopped, use the PLAY AREA button to
select the playback area. Some DVD audio discs have DVD
video areas which can be accessed through this function.
Additionally, SACD discs may contain two or more separate
audio areas, selectable in this way.
< If tracks or chapters are skipped while playback is paused or
stopped, playback is paused or stopped at the start of the
selected track or chapter.
< In programmed playback mode, these buttons will move
between tracks in the programmed order.
The contents accessible as DVD audio and DVD video from
the same DVD disc may differ.
< When playing back video CDs with PBC, note the following:
the . button is disabled. The / button is disabled in
resume mode, but is enabled in play mode. In pause mode,
the / restarts playback at the start of the selected track.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VCD CD SACD DVD-A
DVD VCD CD SACD DVD-A
Fast scanning
Repeat mode
Use the REPEAT button to select the repeat mode for
playback. Repeated presses of the REPEAT button cycle
between the following options:
When playing back, use the SCAN button (m or ,) to
move backwards and forwards (sound is muted for DVD video
and video CD discs). Press PLAY to restart playback at normal
speed at the desired location.
DVD video
Repeated presses of the SCAN buttons changes the scanning
speeds. There are three speeds:
REPEAT CHP
(chapter repeat)
REPEAT TTL
(title repeat)
Fast (1) q Fast (2) q Fast (3) q Play (normal speed)
REPEAT OFF
(no repeat)
The scanning speed is briefly shown on the display.
DVD audio
REPEAT TRK
(track repeat)
REPEAT GRP
(group repeat)
< You can also use the SKIP buttons of the main unit. To start
scanning (or to change the scanning speed), press and hold
the SKIP button for more than one second.
REPEAT OFF
(no repeat)
CD/VCD with PBC off/SACD
Notes on DVD video
REPEAT TRK
REPEAT DSC
(whole disc repeat)
Scanning does not work within menus.
(track repeat)
If forward scanning reaches the end of the last chapter of a
title, playback starts from the start of the next title.
If there is no following title, playback stops.
If backward scanning reaches the start of the first chapter,
normal playback starts from there.
REPEAT OFF
(no repeat)
< Halting playback stops the repeat mode.
< This feature is not available for all discs. The “prohibit” mark
is shown on screen in such cases when an attempt is made to
repeat playback.
< Repeat playback is not possible for video CDs with PBC
enabled.
Notes on DVD audio and video CD (PBC playback)
Scanning does not work within menus.
If forward scanning reaches the end of a track, the scan stops
and playback starts from the beginning of the next track.
If it reaches the last track on the disc, playback stops.
If backward scanning reaches the start of a track, normal
playback starts from the start of that track.
< The following buttons cancel repeat mode:
STOP, OPEN/CLOSE, POWER.
Chapter and track repeat
Notes on video CD (non-PBC playback), audio CDs and
SACD
When this is selected, the currently selected track repeats. If
another track is selected during repeat playback, the newly-
selected track repeats.
Scanning can be carried out across track boundaries.
If backward scanning reaches the start of the disc, playback
starts from the beginning. If forward scanning reaches the
end of the disc, scanning and playback stop.
Title, group, disc repeat
The current title/group or disc repeats. In the case of a DVD,
the current title/group repeats, and for other discs, the whole
contents of the disc are repeated.
Programmed repeat
If programmed playback has been set up, the whole program
is repeated.
Pushing the REPEAT button cycles between REPEAT PGM
(program repeat) and REPEAT OFF (programmed playback
takes place).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CD SACD DVD-A
Programmed playback
Programmed playback allows up to 30 tracks to be played
back in the order you decide.
Note that programmed playback is not possible for DVD video
and video CD discs.
When selecting tracks from a DVD audio disc:
Program running time
PROGRAM
Total 16:50
No. Grp Trk
No. Grp Trk No. Grp Trk
01 01 02
02 01 04
03 02 12
1
04 02
Press the PROGRAM button (either when playing back
––
or stopped).
The program screen appears. If a track is currently playing
back (or paused in the middle of the track), this track is added
as the first item in the programmed playback list.
INPUT:0~9, +10Key
CLEAR:CLEAR Key
Number in programmed Group number Track number
list
Continue pressing the number buttons to add tracks.
< With DVD audio discs, use the GROUP/TITLE buttons to select
the group from which tracks are added.
< Clear mistakes with the CLEAR button (the last entry is
cleared)
PROGRAM
No. Track No. Track
01
Total 00:00
No. Track
< You can only select tracks on the disc (in other words, if the
disc has six tracks, you cannot program track 7!).
––
< Although a DVD audio disc may allow a track to be
programmed (for example a menu track) where no music is
recorded, playback may stop when this track is reached.
INPUT:0~9, +10Key
CLEAR:CLEAR Key
3
Finish the programming by pressing PLAY.
2
Use the number buttons to add tracks to the
programmed playback list.
Programmed playback begins (if the disc is actually being
played back while you are setting the program order, there’s
no need to press PLAY).
Use the +10 button and 0 through 9 buttons in exactly the
same way as when selecting tracks.
Skip between tracks in the programmed playback order using
When selecting tracks from a CD or SACD, the screen
looks like this:
the SKIP buttons (.//).
Program running time
PROGRAM
No. Track No. Track
Total 16:50
No. Track
01 02
02 04
03 12
04
––
INPUT:0~9, +10Key
CLEAR:CLEAR Key
Number in programmed list
Track number
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD
Changing camera angle
When a scene recorded with multiple angles is played, the
angle icon appears on the screen. Each time you press the
ANGLE button while the angle icon is displayed, the camera
angle changes.
Clearing the last track from the list
Push the CLEAR button to clear the last track from the list.
:
:
01/04
Adding tracks to the list
02/04
Use the number buttons to add tracks to the list.
:
:
04/04
03/04
< When no other angle is recorded, the prohibit icon “A” will
be displayed.
< You can change the setting so that the angle icon isn’t
displayed even when a scene recorded with multiple angles is
played. See page 40 for details.
Clearing the whole program
Press the PROGRAM button to clear the program (playback
continues from the current point).
< The maximum number of angles stipulated by the
manufacturer is 9.
The OPEN/CLOSE or the POWER button also clears the
program.
< The ANGLE button doesn’t work during pause.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VCD
DVD VCD DVD-A
Slow motion/frame advance
Selecting audio
Many DVD discs include audio in different languages, as well
as stereo and multi-channel surround versions of the
soundtrack.
Video CDs allow the left, right or stereo channels to be
selected. This facility is not available for audio CDs or SACD
discs.
Slow motion
During playback, press either of the SLOW buttons (
to slow playback in either direction.
/
)
Pressing PLAY resumes normal speed playback.
Pressing the AUDIO button changes between the
different audio tracks available, and the result is shown
on screen.
Repeated presses of the SLOW buttons change the slow
playback speed:
: 1/8 q 1/4 q 1/2 q normal speed
< Sometimes the picture playback will appear to freeze
momentarily when the audio is changed.
:1/20 q 1/16 q 1/12 q playback at normal speed
< It may be necessary to change the audio on some discs using
the on-screen disc menu.
Frame advance
< Some discs cannot have their audio changed in the way
described here, as well as some discs which only have one
audio stream. If you attempt to select different audio with
these discs, the “prohibit” mark is shown on screen.
If you press the SLOW buttons when playback is paused, you
can advance or go back a frame at a time.
Pressing PLAY restarts playback at normal speed.
< Some DVD audio discs have two, or more, audio groups. In
this case, select the audio group.
< Sound is muted while slow playback or frame advance is
taking place.
< You cannot use slow motion or frame advance with video
CDs. Also some discs may not allow this. In these cases, the
prohibit mark “A” is shown on screen if you attempt slow
motion or frame advance.
< If the still or slow picture appears blurred, check the “still
mode” setting (see page 39).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD
DVD
Selecting subtitles
Lip sync
Use the SUBTITLE button to select DVD subtitles.
Repeated presses of this button cycle through available
languages on a disc until OFF is reached (no subtitle).
This function allows you to adjust the synchronization of the
video and audio portions of a DVD.
Press the LIP SYNC button to display the current lip sync value
(default is 0). Use the left and right cursor buttons to adjust
the value. Positive values mean that the sound is delayed
relative to the picture.
< Subtitles do not always appear immediately after the
language has been selected. It may be necessary to wait a
few seconds until the subtitles appear.
< Some captions on some discs cannot be removed or changed
using this button. Additionally, a disc must have at least one
captioning language available for this to work. Some discs
may have only one sub-caption language, in which case, the
choice is obviously restricted to one subtitle or no subtitles.
< Press LIP SYNC again to cancel this setting. Any other
operational display appearing on screen will also cancel this
setting. Note that lip sync should be cancelled if you need to
use the left and right cursor buttons to navigate menus, etc.
< The lip sync value you set is stored when you turn the unit
off, and will be remembered next time you turn the unit on
again.
< It may be necessary to change the subtitles on some discs
using the on-screen disc menu.
< Some discs cannot have their subtitles changed in the way
described here. If you attempt to select a different subtitle
with these discs, the “prohibit” mark is shown on screen.
DVD VCD CD SACD DVD-A
Display dimming
The display on the main unit can be dimmed to suit the
environment in which you listen to music or watch video.
There are three levels and an “off” setting.
Use the FL DIMMER button to cycle between these
settings.
< Note that the OFF setting is not memorized when the power
is turned off. When the unit is switched off with the display
off, and then turned on again, the display is reset to the
minimum brightness.
< In OFF mode, when you press a button such as PLAY, the
illuminations turn temporarily on.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VCD
DVI output
DVI level
When DVI output is enabled, the black areas shown on the
monitor may not appear dark enough. In this case, it is
necessary to select the EXPAND option.
When the DVI output is selected and the format is
visible on the front panel’s display, use the right cursor
button to select between EXPAND or NORMAL.
The relevant data are:
NORMAL: 16 (black) to 235 (white)
EXPAND: 0 (black) to 246 (white)
The DVI ON/OFF button turns output from the DVI output on
and off. In order to use this output, a DVI/HDCP-compliant
television must be used.
< If the display is not HDCP-compliant, video playback may not
occur.
< When this DVI output is turned on, even if progressive scan
has been selected for the component video outputs, an
interlaced signal is output.
DVI output format
When DVI output is turned on, the front panel’s display
shows the current format. Use the up and down cursor
buttons to change the format when it is displayed.
DVI output aspect ratio
It may sometimes be necessary to change the aspect ratio
from 4:3 when video is output and displayed through the DVI
terminal, especially when 720p or 1080i is selected. Use the
television (monitor) controls to change the format.
If your television (monitor) cannot change the aspect ratio,
change the output mode of the UX-3 in the following way:
When the DVI output is selected and the format is
visible on the display, use the left cursor button to
select between “DVI 4:3” or “DVI FULL” to match the
television (monitor).
480p (NTSC) or 576p (PAL)
1080i
720p
(i=interlaced, p=progressive scan)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VCD CD SACD DVD-A
DVD VCD CD SACD DVD-A
Turning video on and off
Clock Mode
Use the VIDEO ON/OFF button to turn video output to the
television (monitor) on and off. It is not necessary to turn video
off, but you may notice a slight improvement in audio quality if
you turn off the video when playing back SACD discs and CDs
without video images.
Word sync
For highly accurate playback, you can use the word clock
(sync) output of an external unit such as the Esoteric G-25U,
D-70 or G-0s to synchronize your whole audio system.
Use the CLOCK MODE (main unit) button to switch
between Word ON and Word OFF.
When the unit is synchronizing to the external clock, the ring
surrounding the button flashes. When it is locked, the button
lights.
Note that this setting is not memorized when the power is
turned off.
DVD SACD DVD-A
The main unit can accept and synchronize to the following
frequencies received from external devices:
44.1kHz, 48kHz, 88.2kHz, 96kHz, 100kHz, 176.4kHz,
192kHz as well as frequencies which are 96% of these
values, in the 4% DOWN mode.
Analog sound output (2CH/MULTI)
Note that the sync connection should be made before the
CLOCK MODE button is pressed. If no valid word sync signal
is received, the display shows “No Word!”.
4% DOWN mode
When playback is stopped, use the 2CH/MULTI button to select
either 2CH (stereo) or MULTI (multi-channel surround) audio
output.
This allows a 4% reduction in frame rate. PAL video plays
back at 25 frames per second (fps), but movies are shot at
24fps. This mode helps to resolve the discrepancy by allowing
an external clock source at 4% less than standard to be
received. The external clock source should be set to this 4%
frequency reduction (called “PAL FILM” on the G-0 and G-0s
models).
This setting is also reflected in the configuration screen (see page 31).
2CH
The unit outputs 2-channel audio from the the i.LINK (AUDIO)
and the AUDIO OUT terminals.
If multi-channel program material is played, the multi-channel
material will be downmixed to two channels and the
DOWNMIX indicator will light on the display.
See page 32 for how to set the downmix mode.
Press and hold the CLOCK MODE button on the main
unit for three seconds or more to enter this mode.
The ring surrounding the button lights orange. Pressing this
button again turns off the word sync.
MULTI
Note that the signals from the S-Video and composite video
outputs are cancelled when this mode is selected. In addition,
the audio pitch drops.
The unit outputs the multi-channel surround sound.
Select this when the i.LINK (AUDIO) terminal is connected to a
surround sound amplifier with a decoder.
5.1 indicator will light on the display.
< Note that if “MULTI” is selected, only the front L/R sound of
the multi-channel material will be output from the analog
AUDIO OUT terminals.
< This setting has no effect on the DIGITAL OUT terminals.
< This setting is ignored if you play a DVD-Video with the Audio
Digital Out set to “Stream”(page 37) and the i.LINK output
set to “i.60958”(page 42). To use this setting, set the Audio
Digital Out to “Stream” and the i.LINK output to “i.PCM”.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VCD CD SACD DVD-A
Changing the display mode
DVD video playback (on-screen display)
(no display)
Currently-playing title
Elapsed time of current title
Title Chapter Total Elapsed Total Remain
01
03/37
10:53
140:17
Currently-playing Number of chapters
chapter in current title
Time remaining for
current title
During playback, it is possible to change the display as shown
here. The display on both the main unit, and the on-screen
display (when the video output is on) changes.
Elapsed time of current chapter
Title Chapter Elapsed Remain
01 03/37 0:03 3:39
When playback stops, the display mode reverts to the first type
of display.
Time remaining for current chapter
Total number of audio
versions recorded
Current Audio channels
DVD video playback (main unit display)
Audio format
Language of audio format
Audio 1/2 : Dolby Digital 3/2.1 English
Subtitle : 01/03 Japanese
Elapsed time of current title
Number of subtitles available
Currently-selected subtitle
DVD video (stopped, on-screen display)
Currently-playing title
Currently-playing chapter
(no display)
Total number of titles on disc
TotalTitle
12
Time remaining for current title
Elapsed time of current chapter
< When DVD video playback is stopped, the display of the main
unit doesn’t change.
DVD audio playback (main unit display)
Currently-playing group
Currently-playing track
Elapsed time of
current track
Time remaining for current chapter
Time remaining for current track
Elapsed time of current group
Time remaining for current group
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD audio playback (on-screen display)
SACD/CD/video CD (stopped, main unit
display)
(no display)
Current group
Elapsed time of current track
Group Track Elapsed Remain
01 02/10 01:50 04:41
Number of tracks on disc
Total disc running time
Time remaining for current track
Currently-playing track
Total number of tracks on disc
SACD/CD/video CD playback (on-screen
display)
Elapsed time of current group
(no display)
Group Track
Total Elapsed Total Remain
01
02/10
05:50
38:00
Number of tracks
on disc
Time remaining for current group
Elapsed time of current track
Track Elapsed Remain
02/36
00:09
03:51
Audio format
Sampling frequency
Currently playing track
Time remaining for current tracks
Audio 1/1: PPCM 5.1ch / 96kHz / 24bit
Total number of audio
versions recorded
Audio channels
Bit rate
Total elapsed time
Track Total Elapsed Total Remain
02/36
03:09
56:51
DVD audio (stopped, on-screen display)
Total time remaining (disc)
(no display)
Track Total Elapsed TotalTime
02/36
03:09
60:00
Total number of groups on disc
Total disc running time
Total Group
04
SACD/CD/video CD (stopped, on-screen
display)
< When DVD audio playback is stopped, no display appears on
the main unit.
(no display)
SACD/CD/video CD playback
(main unit display)
TotalTrack TotalTime
036
61:35
Currently playing track
Elapsed time of current track
Number of tracks on disc
Total disc running time
< The above does not apply to video CDs played back using the
PBC system.
Time remaining for current track
Total elapsed time (disc)
Total time remaining (disc)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (introduction)
1
Turn on the main unit, and the television (monitor).
If no cursor is visible on the screen, using the left and right
buttons changes between the top tabbed menus.
Use the up and down buttons to highlight menu items within
these tabbed menus. RETURN returns to the top level.
4
Enter the menu item with the right cursor button.
2
Press the SETUP button.
Analog Out
2ch *
Digital Out
Multi Channel
CD Digital Direct
Audio DRC
Group Playback
2ch Down Mix
The following appears on screen.
Move
Return
Select
Exit
5
Use the up and down cursor buttons to select the
options within the menu item, and ENTER to confirm
the entry.
Analog Out
Digital Out
CD Digital Direct
Audio DRC
2ch *
ON *
Direct *
OFF *
Group Playback
2ch Down Mix
Single *
Lo/Ro *
Move
Return
Select
Exit
< Factory settings are marked with an asterisk “*”.
< Exit the setup mode by pressing SETUP once again.
< Although it is possible to enter the setup screen while
playback is continuing (or in resume mode), not all menu
functions will be available. Expand the number of available
functions by pressing the STOP button twice.
Individual menu functions are described on pages 31 through
41.
3
5
Repeat steps
through
as required.
3
Use the cursor buttons to navigate the menus.
6
Exit the setup mode by pressing SETUP once more.
Analog Out
2ch *
Digital Out
CD Digital Direct
Audio DRC
Group Playback
2ch Down Mix
Multi Channel
The display on the main menu also gives some menu
messages and allows settings to be made, but it is easier to
use the on-screen display to make these settings (remember
that video output must be turned on!).
Move
Return
Select
Exit
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (Audio)
Analog output settings
Digital output settings
[AUDIO q Analog Out]
[AUDIO q Digital Out]
Analog Out
2ch *
Analog Out
Digital Out
CD Digital Direct
Audio DRC
Multi Channel
Digital Out
CD Digital Direct
Audio DRC
ON *
OFF
Group Playback
2ch Down Mix
Group Playback
2ch Down Mix
Move
Return
Select
Exit
Move
Return
Select
Exit
2ch *
ON *
Outputs 2-channel audio from the the i.LINK (AUDIO) and the
AUDIO OUT terminals.
Audio is output from the i.LINK (AUDIO) terminal and the
DIGITAL OUT terminals.
If multi-channel program material is played, the multi-channel
material will be downmixed to two channels and the
DOWNMIX indicator will light on the display.
OFF
Audio is not output from the i.LINK (AUDIO) terminal and the
DIGITAL OUT terminals. If you are not using the these
terminals, we suggest that you use this OFF setting for better
analog sound.
See page 32 for how to set the downmix mode.
Multi Channel
The unit outputs the multi-channel surround sound.
Select this when the i.LINK (AUDIO) terminal is connected to a
surround sound amplifier with a decoder.
5.1 indicator will lights on the display.
< Digital sound from SACD discs cannot be output from the
DIGITAL OUT terminals.
< DVD audio at 192kHz or 174.4kHz is converted to
< Note that if “Multi Channel” is selected, only the front L/R
sound of the multi-channel material will be output from the
AUDIO OUT terminals.
96/88.2kHz sampling frequency.
< If downsampling is turned on, 192kHz and 96kHz discs will
be automatically converted to 48kHz digital audio, and
174.4kHz and 88.2kHz discs will be converted to 44.1kHz
audio. Some discs converted in this way may not output
digital audio (depending on the disc).
< Note that some DVD discs cannot be downmixed (from multi
channel to 2-channel). In these cases, no digital sound will be
output.
< Speakers should be set up properly for multi-channel use. See
page 36 for details.
CD Digital Direct
[AUDIO q CD Digital Direct]
< This setting has no effect on the DIGITAL OUT terminals.
Analog Out
Digital Out
CD Digital Direct
Audio DRC
Direct *
Normal
Group Playback
2ch Down Mix
Move
Return
Select
Exit
Direct *
This setting bypasses unnecessary circuitry and provides better
sound quality when listening to audio CDs.
Normal
Use this setting only when playing back DTS-CDs (DTS digital
surround).
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (Audio)
Audio DRC (Dynamic Range Controlling)
Downmix
[AUDIO q Audio DRC]
[AUDIO q 2ch Down Mix]
Analog Out
Analog Out
Digital Out
Digital Out
CD Digital Direct
Audio DRC
CD Digital Direct
Audio DRC
ON
Group Playback
2ch Down Mix
OFF *
Group Playback
2ch Down Mix
Lo/Ro *
Lt/Rt
Move
Return
Select
Exit
Move
Return
Select
Exit
ON
Lo/Ro *
Usual stereo mode. Use this for stereo playback, etc.
Applies dynamic range control to Dolby Digital material,
reducing the volume of loud sounds, and increasing the
volume of quiet ones. This is useful for spoken word material,
etc. as well as nighttime listening.
Lt/Rt
This mode is useful when recording multi-channel sound on a
cassette tape deck or CD recorder connected via the AUDIO
OUT jacks. With a Dolby Pro Logic decoder, the recorded
sound can be decoded into multi-channel sound.
OFF *
Turns off the audio dynamic compression.
< This function is effective only when playing back a DVD disc
recorded with Dolby Digital. This control has no effect on
other discs.
< Select between 2-channel and multi-channel modes using the
2CH/MULTI remote control button.
< Note that this setting is ignored for DVD audio discs and
SACD discs; these are downmixed in the Lo/Ro mode
automatically.
< The overall effect of this setting depends on many things: the
disc being played, the amplifier, and the speakers used for
reproduction.
Group playback mode (DVD audio)
[AUDIO q Group Playback]
Analog Out
Digital Out
CD Digital Direct
Audio DRC
Group Playback
2ch Down Mix
Continue
Single *
Move
Return
Select
Exit
Continue
Plays all groups. Moving between groups is not possible when
the menu screen is displayed.
Single *
Plays the group selected using the menu. Fast forward, track
skip, etc. cannot be used to move between groups.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (Video)
4
Press RETURN when done, to return to the memory
selection screen, or SETUP to exit the setup menu
completely.
Video adjustment
[VIDEO q Video Adjust]
1
Highlight the Video Adjust menu item and press the
ENTER button.
Video Adjust
Progressive Setting
Progressive scan setting
[VIDEO q Progressive Setting]
Video Adjust
Move
Return
Select
Exit
Progressive Setting Progressive Mode
DCDi
Reference*
Move
Memory 1
Return
Memory 2
Select
Memory 3
Exit
Move
Return
Select
Exit
Near the bottom of the display, a row of four options
appears: Reference, and three memory settings (Reference
contains the factory default settings and the three memories
can be used to make video settings for different monitors,
types of program material, etc.).
The progressive-scan mode setting menu has two sub-menus:
Progressive Mode (progressive scan mode) and DCDi.
Progressive Mode
Usually, you will not need to change these settings, but there
may be occasions when you want to alter one or two
parameters for a perfect picture.
Within Progressive Mode, there are two settings: Auto* and
Video (use the left and right cursor buttons to select these
choices). Typically, the Auto setting should be used but in the
case of jagged or blurred playback of a DVD, you may want
to select the Video option.
2
To change settings, use the left and right cursor buttons
to highlight one of the Memory settings, and press
ENTER.
DCDi
< Selecting the Reference setting returns you to the VIDEO
menu.
This is a special technology allowing high-quality images to be
produced and you can set this On or Off* when progressive
scan is taking place. Usually, you will not need this switched
on, but some material demands the use of this progressive
scan technology, especially if you notice “jaggies” on
diagonal lines.
3
Use the up and down buttons to select the parameter,
and the left and right buttons to change the value.
Sharpness
Adjusts the sharpness of the picture shown on the
monitor.
Contrast
Adjusts the picture contrast
Brightness
Adjusts the brightness of the picture
Gamma
Adjusts the gamma value of the picture
Hue
A note on progressive-scan
The video on DVD discs may be either originally shot on video
or film. Video material has a frame rate of 30fps (NTSC) while
film is at 24 frames per second. In progressive-scan mode,
film material is converted to 60 frames per second, and the
player adjust the picture match the quality from a cinema
screen. As mentioned above, Auto is the usual setting for
Progressive Mode, but Video may be used if the picture
appears jagged.
Adjusts the green/red balance of the picture (only for
progressive-scan and S-Video output)
Chroma Level
Adjusts the chroma level of the picture
Chroma Delay
Sets the delay between the Y and C signals (only affects
progressive-scan pictures).
Black Setup
Use this to enhance the black level of the picture, to assist
in the “3D look” of some scenes. Normally, this setting
should be 0 IRE. Change it only if really necessary.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (Language)
To select a language other than English or Japanese, move
the cursor to Other and press ENTER.
Audio language selection
[LANGUAGE q Audio Language]
If you select the List of Language field, you see a list of ten
relatively common languages. Select from this list by moving
the cursor and pressing ENTER.
Audio Language
Subtitle Language
Subtitle Display
OSD Language
English *
Japanese
Other
If the language you want is not listed here, but is listed on
page 35, move the cursor to the Code (0 - 9) field (all
numbers are reset as dashes) and use the number buttons to
enter the four-digit code for that language. Press ENTER
when done.
Move
Return
Select
Exit
This provides an alternative to the AUDIO button for selecting
alternative soundtracks. The default setting is English* but
you can also select Japanese, or a number of other different
languages as the audio track to be played from a multi-lingual
disc.
< If the selected language is not available on the disc, the first
subtitle language of the disc is used.
To select a language other than English or Japanese, move
the cursor to “Other” and press ENTER.
Displaying subtitles
[LANGUAGE q Subtitle Display]
Audio Language
Subtitle Language
Subtitle Display
OSD Language
English *
Japanese
Other
Audio Language
Subtitle Language
Subtitle Display
OSD Language
ON *
OFF
List of Language
en : English
~
0
5
1
4
Code (0 9)
Move
Return
Select
Exit
If you select the List of Language field, you see a list of ten
relatively common languages. Select from this list by moving
the cursor and pressing ENTER.
Move
Return
Select
Exit
This turns subtitling ON* or OFF.
Note that the captions on some disks cannot be turned off.
If the language you want is not listed here, but is listed on
page 35, move the cursor to the Code (0 - 9) field (all
numbers are reset as dashes) and use the number buttons to
enter the four-digit code for that language. Press ENTER
when done.
On-screen display language
[LANGUAGE q OSD Language]
< If the selected language is not available on the disc, the first
language of the disc is played.
Audio Language
Subtitle Language
Subtitle Display
Subtitle language selection
English *
Japanese
OSD Language
[LANGUAGE q Subtitle Language]
Move
Return
Select
Exit
Audio Language
Subtitle Language
Subtitle Display
OSD Language
English *
Japanese
Other
There are two choices here: English* and Japanese.
NOTE: If the unit is set to Japanese and you find it impossible
to read the menu settings, etc., you can restore all the factory
default settings, and the menus will appear in English again
(all other settings will be wiped out. Alternatively, press
Move
Return
Select
Exit
SETUP, navigate to the third tab (
” and select the first option “
), move down to “OSD
(English)”.
This provides an alternative to the SUBTITLE button for
selecting alternative subtitle languages. The default setting is
English* but you can also select Japanese, or a number of
other different languages for the subtitles to be displayed.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
Language
Japanese (ja)
English (en)
French (fr)
Code
1001
0514
0618
0405
0920
0519
2608
1412
1620
1922
1821
1115
0512
0101
0102
0106
0113
0118
0119
0125
0126
0201
0205
0207
0208
0209
0214
0215
0218
0301
0315
0319
0325
0401
0426
0515
0520
0521
0601
0609
0610
0615
0625
0701
0704
0712
Language
Code
0714
0721
0801
0809
0818
0821
0825
0901
0905
0911
0914
0919
0923
1009
1023
1101
1111
1112
1113
1114
1119
1121
1125
1201
1214
1215
1220
1222
1307
1309
Language
Pashto, Pushto (ps) 1619
Quechua (qu) 1721
Rhaeto-Romance (rm) 1813
Code
Guarani (gn)
Gujarati (gu)
Hausa (ha)
German (de)
Italian (it)
Hindi (hi)
Kirundi (rn)
1814
1815
Croatian (hr)
Hungarian (hu)
Armenian (hy)
Interlingua (ia)
Interlingue (ie)
Inupiak (ik)
Romanian (ro)
Spanish (es)
Chinese (zh)
Dutch (nl)
Kinyarwanda (rw) 1823
Sanskrit (sa)
Sindhi (sd)
Sangho (sg)
1901
1904
1907
Portuguese (pt)
Swedish (sv)
Russian (ru)
Korean (ko)
Greek (el)
Serbo-Croatian (sh) 1908
Indonesian (in)
Icelandic (is)
Hebrew (iw)
Yiddish (ji)
Sinhalese (si)
Slovak (sk)
Slovenian (sl)
Samoan (sm)
Shona (sn)
Somali (so)
Albanian (sq)
Serbian (sr)
Siswati (ss)
Sesotho (st)
Sundanese (su)
Swahili (sw)
Tamil (ta)
1909
1911
1912
1913
1914
1915
1917
1918
1919
1920
1921
1923
2001
2005
2007
2008
2009
2011
2012
2014
2015
2018
2019
2020
2023
2111
2118
2126
2209
2215
2315
2408
2515
2621
Afar (aa)
Abkhazian (ab)
Afrikaans (af)
Amharic (am)
Arabic (ar)
Javanese (jw)
Georgian (ka)
Kazakh (kk)
Greenlandic (kl)
Cambodian (km)
Kannada (kn)
Kashmiri (ks)
Kurdish (ku)
Kirghiz (ky)
Assamese (as)
Aymara (ay)
Azerbaijani (az)
Bashkir (ba)
Byelorussian (be)
Bulgarian (bg)
Bihari (bh)
Latin (la)
Telugu (te)
Tajik (tg)
Lingala (ln)
Bislama (bi)
Bengali (bn)
Tibetan (bo)
Breton (br)
Catalan (ca)
Corsican (co)
Czech (cs)
Laothian (lo)
Lithuanian (lt)
Latvian (lv)
Thai (th)
Tigrinya (ti)
Turkmen (tk)
Tagalog (tl)
Setswana (tn)
Tonga (to)
Turkish (tr)
Tsonga (ts)
Tatar (tt)
Malagasy (mg)
Maori (mi)
Macedonian (mk) 1311
Malayalam (ml)
Mongolian (mn)
Moldavian (mo)
Marathi (mr)
Malay (ms)
1312
1314
1315
1318
1319
1320
1325
1401
1405
1415
1503
1513
1518
1601
1612
Welsh (cy)
Danish (da)
Bhutani (dz)
Esperanto (eo)
Estonian (et)
Basque (eu)
Persian (fa)
Finnish (fi)
Twi (tw)
Ukrainian (uk)
Urdu (ur)
Maltese (mt)
Burmese (my)
Nauru (na)
Uzbek (uz)
Vietnamese (vi)
Volapük (vo)
Wolof (wo)
Xhosa (xh)
Yoruba (yo)
Zulu (zu)
Nepali (ne)
Fiji (fj)
Norwegian (no)
Occitan (oc)
Oromo (om)
Oriya (or)
Faroese (fo)
Frisian (fy)
Irish (ga)
Scots-Gaelic (gd)
Galician (gl)
Panjabi (pa)
Polish (pl)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (General/Speaker setup)
Use these speaker setup menus when the i.LINK
Speaker distance
[GENERAL q Speaker Setting q Distance]
(AUDIO) terminal is connected to a surround sound
amplifier with a decoder, and when you don’t use the
speaker menus of the amplifier.
Ideally, the speakers should be placed so that they are all the
same distance from the listening position. If this is not
possible, you should use this method described here to adjust
them individually. It is also possible to adjust all distances
together. The point of these settings is to provide the best
synchronization between sound and image by delaying the
sound by an appropriate amount. The subwoofer is not
included in this setting (the placement of the subwoofer is
less critical than that of other speakers).
There is no need for this setup when not using the i.LINK
(AUDIO) terminal, or when you use the speaker menus of the
amplifier. In this case, leave this setup as it is (factory settings).
< This setup has an effect on the sound output from the i.LINK
(AUDIO) terminal and the AUDIO OUT terminals when the
Analog Out setting is set to “Multi Channel”.
< In the following cases, the settings made here are ignored:
• When the Analog Out setting is set to “2ch”.
• Play a DVD-Video with the i.LINK output set to “i.60958”.
Speaker Setting
Size
Audio Digital Out Distance (m) L/R
3.0
3.0
3.0
Speaker Size
[GENERAL q Speaker Setting q Size]
Video Out
Level (dB)
Test Tone
C
Display Setting
Parental Lock
SR/SL
Move
Return
Select
Exit
Speaker Setting
Audio Digital Out Distance (m)
Size
L/R
C
Large *
Small
Video Out
Display Setting
Parental Lock
Level (dB)
Test Tone
SR/SL
SW
The L/R setting changes the distance of all speakers together.
Pressing the up button adds 0.1m to each value, and pressing
the down button subtracts 0.1m from each value.
Distances are measured in meters (1 meter = just over 3 feet,
and 0.1 meter = about 4 inches).
Move
Return
Select
Exit
Select the size (Large* or Small) independently for the L/R
(front pair of speakers), the C (center speaker) and the SR/SL
(surround pair of speakers). Turn the subwoofer (SW) ON* or
OFF (if you have no subwoofer).
Carry out this operation first before setting the other speaker
distances.
After setting the L/R, C and SR/SL speaker distances together,
you can now set the center and surround pair distances. The
minimum distance for these is 0m and the maximum is 9m,
with the additional restrictions described here.
Large *
Select this when the connected speakers can fully reproduce
bass frequencies.
< The distance that you set for the center speaker cannot be
greater than the distance set for the L/R pair and must be
within 1.7m of that L/R distance.
Small
Select this when the connected speakers are rather small and
cannot reproduce bass frequencies.
So for example, if the distance to the L/R pair is set to 5.0m,
the center distance must be between 3.3m (5 - 1.7) and 5m.
When this setting is selected, bass frequencies are output
from the subwoofer (if no subwoofer is connected, from the
front speakers).
< The distance that you set for the SR/SL surround pair cannot
be greater than the distance set for the L/R pair (and must be
within 9m of that distance).
So with the L/R pair set at 5m, the SR/SL pair distance can be
set from 0m to 5m.
OFF
Select this when no speaker is connected. The sound is
output from the front (or surround) speakers.
< When the front speaker is set to “Small”, the subwoofer is
set to “ON” automatically. You cannot set the subwoofer
“OFF”.
Speaker levels
[GENERAL q Speaker Setting q Level]
ON (subwoofer only)
Select this when a powered subwoofer is connected.
Use this to set the relative levels of the speakers. You can set
the L/R pair together, and the center, and surround rear pair
independently, as well as the subwoofer. The maximum value
you can set here is 0dB and the minimum is –12dB, with
settings made in 0.5dB increments. The default setting is each
speaker channel set to 0dB.
< For the center and surround pair options, if these speakers are
not physically present, you can select OFF to prevent any
output from those channels (you cannot turn off the front L/R
pair). Any speakers turned off will downmix (if this option is
selected) to the other enabled channels.
< Turning downmix on and off may affect the overall volume.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (General)
1. When you are ready to start, highlight the “Test Start”
and press the ENTER button.
Digital output formats
[GENERAL q Audio Digital Out]
Speaker Setting
Size
Audio Digital Out Distance (m) L/R
0.0
0.0
0.0
0.0
0.0
Speaker Setting
Audio Digital Out Dolby Digital
Video Out
Display Setting
Parental Lock
Video Out
Display Setting
Parental Lock
Level (dB)
Test Tone
C
SR
SL
Stream *
Stream *
Stream *
ON *
DTS
MPEG Audio
Down Sample
SW
Test Start
Move
Return
Select
Exit
Move
Return
Select
Exit
The unit outputs test tone from each channel in turn at the
specified level for each channel.
Use this to select the format of different digital audio types
for different purposes, as detailed below:
< Test tone at very high levels may not be good for your
speakers. Make sure the level of your system is turned down
to a reasonable level before carrying out this operation.
< Test tone from subwoofer may be nearly inaudible. Check the
level of subwoofer using source material containing low
frequency sound.
Dolby Digital
Select either “Stream” for use with Dolby Digital compatible
amplifiers or “PCM” for use when connecting to a CD
recorder, MD deck, etc.
< The unit won’t output test tone when “i.60958” is selected.
Select “i.PCM” to use test tone (see page 42).
dts
Select either “Stream” for connection to a dts-compatible
amplifier, or “PCM” for use with more general equipment.
Do not select the Stream option when connecting to non-dts-
compatible equipment.
< The unit won’t output test tone when an SACD disc is (or had
been) loaded. In this case, remove the disc, turn the unit off
and on, and try again.
2. Adjust the levels and continue using the test tone as
necessary until you are happy with the balance.
MPEG Audio
Select either “Stream” for connection to an MPEG-compatible
amplifier, or “PCM” for use with more general equipment.
Speaker Setting
Size
Audio Digital Out Distance (m) L/R
0.5
0.0
0.0
0.0
0.0
Down Sample
Video Out
Display Setting
Parental Lock
Level (dB)
Test Tone
C
SR
SL
Enable (ON*) or disable (OFF) downsampling. That is, all
digital signals are converted, and output at 48kHz or
44.1kHz. Use this if your amplifier does not have
96kHz/88.2kHz capability.
SW
Test Start
Move
Return
Select
Exit
Note that even when downsampling is turned off, some discs
are automatically downsampled to 48kHz or 44.1kHz.
Also note that even when downsampling is turned off, all
discs with sampling frequencies of 192kHz or 176.4kHz are
always downsampled to 96kHz or 88.2kHz respectively.
Test tone length
[GENERAL q Speaker Setting q Test Tone]
Speaker Setting
Size
Audio Digital Out Distance (m)
Video Out
Display Setting
Parental Lock
Level (dB)
Test Tone
2sec
5sec *
10sec
Move
Return
Select
Exit
Select the Test Tone menu item, and choose between 2, 5*
and 10 seconds. This represents the length of time that the
test tone is output from each speaker when Test Start is
selected.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (General/Video Out)
16:9 *
Use with a 16:9 wide television.
Speaker Setting
Audio Digital Out TV Screen
16 : 9 *
Video Out
Display Setting
Parental Lock
S-Video Out
Comp. Video
PL-NT Conv.
Caption
S2 *
Interlace *
OFF *
OFF *
Still Mode
Auto *
4:3 picture
16:9 picture
Move
Return
Select
Exit
4:3LB (Letterbox)
This menu item contains a number of different options, all
concerned with the video output from the unit.
This mode is used with 4:3 televisions. 4:3 images are
displayed normally. 16:9 images are visible at their full
width, but a blank area is left at the top and bottom of the
screen.
TV screen
[GENERAL q Video Out q TV Screen]
Because the shape of the television or monitor may not match
the shape of the movie frame, you may need to change the
way in which the image is displayed to avoid distortion on
older televisions, which use a 4:3 aspect ratio; high-definition
televisions use 16:9 (as do movies).
Note that you may need to read your television’s manual in
conjunction with this section in order to achieve the best
results. Some discs do not allow the aspect ratio to be
changed and you will therefore have to change the aspect
ratio on the TV.
4:3 picture
16:9 picture
4:3PS (Pan & Scan)
This mode is used with 4:3 televisions. 4:3 images are
displayed normally. When showing 16:9 programs, the full
height of the screen is used, but the left and right part of
the image are cut off.
Make this setting while playback is stopped; you cannot do
this while playing back a disc.
4:3 picture
16:9 picture
S-Video output
[GENERAL q Video Out q S-Video Out]
If a television is connected using the S-Video output, the
signal can be set to change the aspect ratio of the television
automatically.
S1
The aspect ratio information (16:9 and 4:3) is included in the
S1-Video signal.
S2*:
In addition to the information of S1, “4:3 Letterbox”
information is included in the S2-Video signal. If your wide-
screen television is compatible with S2-Video, correct aspect
ratio will be selected automatically.
< If the picture is stretched or distorted, select “S1”.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Component video output
Closed captioning
[GENERAL q Video Out q Comp. Video]
[GENERAL q Video Out q Caption]
This setting allows the selection of interlaced (Interlace*) or
progressive-scan (Progressive) video from the component
video outputs.
The unit can play back DVD discs which include closed
captioning information and show the closed captions (on a
suitably-equipped television).
Progressive-scan video provides a better, clearer picture.
However, it is not supported by every television or monitor,
and you should ensure that this is supported fully before
turning on this option.
Turn this function either ON or OFF*.
Still mode
[GENERAL q Video Out q Still Mode]
< When your TV isn’t compatible with progressive scan, never
select “Progressive”. No picture will be shown on the
monitor.
In case you select “Progressive” by mistake, connect your TV
via the VIDEO OUT jack or S-VIDEO jack to display the Setup
menu and change the setting to “Interlace”, or initialize the
settings (see page 7).
There are three options to enable different still modes for
DVD, depending on whether a movie or other type of video is
being played back. This setting determines the clearest still
picture obtained when the DVD playback is paused.
Auto*
Automatically chooses between field and frame modes.
‘CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH
THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625
PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH THE CONNECTION
TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH
THIS MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.’
Field
Usually provides a sharp still picture. But depending on the
disc, the image might be shaky even when “Field” is selected.
Frame
Usually provides a better still picture with movie DVDs.
PAL-NTSC conversion
[GENERAL q Video Out q PL-NT Conv.]
This allows you to play back and show NTSC discs on PAL
equipment, or the other way round. There are three options:
OFF*
PAL discs can only be shown on PAL equipment, and NTSC
discs can only be shown on NTSC equipment. Use this setting
to produce the best possible picture, by playing each type of
disc on the appropriate equipment.
PAL>NTSC
PAL discs can be displayed on NTSC equipment. The bottom
part of the picture is cut off, and the height is elongated.
NTSC>PAL
NTSC discs can be played back on PAL equipment. The height
of the picture is reduced.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings (General/Display)
Parental Control
Speaker Setting
Audio Digital Out
Video Out
Speaker Setting
Audio Digital Out
Video Out
Password Set/Change
Display Setting
Parental Lock
On Screen Display
Angle Indicator
Background
ON *
ON *
Black *
Display Setting
Parental Lock
Level
Country Code
OFF
us
Move
Return
Select
Exit
Move
Return
Select
Exit
It is possible to protect the playback of discs containing material
unsuitable for viewing by children which parents do not wish
their children to view, as DVD discs can contain information
regarding their suitability for children recorded on them. Such
levels may vary from country to country, and this unit allows
such variable restrictions .
On-screen display
[GENERAL q Video Out q On Screen Display]
When a button is pressed and this setting is ON* , the screen
shows that button’s name and/or icon, etc. Turn this OFF if
you do not need this kind of on-screen display.
Before a disc protected in this way can be played back on the
unit, it is necessary to enter a password which temporarily
changes the level to a more “relaxed” value.
Angle indication
[GENERAL q Video Out q Angle Indicator]
These different levels of protection also allow you to change the
levels of protection as your children grow up, for example.
For discs which support different angles (see page 23), this
allows the angle indicator mark to be displayed (ON*) or not
(OFF) when an alternative angle is available on the section of
the disc being played back.
NOTE: If the user settings are reset, the password (and hence
parental control) is disabled.
Setting the password
Background color
[GENERAL q Parental Lock q Password Set/Change]
[GENERAL q Video Out q Background]
When the disc is stopped, this sets the background color of
the screen. Choose between Black*, Gray and Blue.
Speaker Setting
Audio Digital Out
Video Out
Password Set/Change
Display Setting
Parental Lock
Level
Country Code
OFF
us
Password Set
Move
Return
Select
Exit
The first time that you use the unit (or the first time that you
use the unit after resetting to factory settings), other parental
lock options are disabled. All you can do is enter a 4-digit
password using the number buttons on the remote control
unit.
Enter this number (and remember it!), as you will need it to
change the level of control in the future as well as to
temporarily unlock discs for playback.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the level of control
[GENERAL q Parental Lock q Level]
Country
Input Code Country Code
ARGENTINA
AUSTRALIA
AUSTRIA
0118
0121
0120
0205
0218
0301
0312
0314
0411
0609
0618
0405
0811
0914
0904
0920
1016
1118
1325
1324
1412
1426
1415
1611
1608
1620
1821
1907
0519
0308
1905
2023
2008
0702
2119
ar
au
at
Speaker Setting
Audio Digital Out
BELGIUM
be
br
ca
cl
Video Out
Password Set/Change
BRAZIL
Display Setting
Parental Lock
Level
Country Code
OFF
us
CANADA
CHILE
Level
1
2
3
4
5
6
7
8
OFF
CHINA
cn
dk
fi
DENMARK
Move
Return
Select
Exit
FINLAND
Once a password has been entered, you can enter a control
level, ranging from 1 (strict control) through 8 (much less
strict) to OFF* (no control at all).
When Level is selected, you must make the selection within
30 seconds. Press ENTER to confirm the setting.
FRANCE
fr
GERMANY
HONG KONG
INDIA
de
hk
in
INDONESIA
ITALY
id
it
JAPAN
jp
Country Code
[GENERAL q Parental Lock q Country Code]
KOREA, REPUBLIC OF
MALAYSIA
MEXICO
kr
my
mx
nl
NETHERLANDS
NEW ZEALAND
NORWAY
nz
no
pk
ph
pt
ru
sg
es
ch
se
tw
th
gb
us
Speaker Setting
Audio Digital Out
Video Out
Password Set/Change
PAKISTAN
Display Setting
Parental Lock
Level
Country Code
7
us
PHILIPPINES
PORTUGAL
RUSSIAN FEDERATON
SINGAPORE
SPAIN
~
Code us
Code (0 9)
2
1
1
9
Move
Return
Select
Exit
As well as the level, you can change the country to which the
level applies. Select the Country code option, enter the 4-digit
country code and press ENTER. The two-letter country code
changes.
SWITZERLAND
SWEDEN
TAIWAN, PROVINCE OF CHINA
THAILAND
UNITED KINGDOM
UNITED STATES OF AMERICA
Playing a controlled disc
If you then attempt to play a disc whose level is greater than
the level you have set, the disc shows a screen which explains
that the disc cannot be played with this level of control.
Following the on-screen instructions, you will be prompted to
turn off the level, temporarily while the disc is being played.
Enter the 4-digit password, and then press ENTER. The disc
can then be played.
If you eject the disc or turn off the unit with the disc inserted,
the password to play back the disc is “forgotten” by the unit.
To play the disc again, you must enter the password again.
Resetting the password
You can reset the password at any time. Choose the
Password Set/Change option, enter the old password and
then enter the new password (number buttons).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
i.LINK (AUDIO) Output Setting
When the i.LINK (AUDIO) terminal is connected to an amplifier or
a D/A converter, select proper i.LINK output setting.
< There is no difference between i.60958 and i.PCM as far as
SACD or DVD-Audio disc playback is concerned.
< Set the Analog Out setting to “Multi channel” to output the
surround sound from a DVD-Audio and SACD disc.
When the Analog Out setting is set to “2ch”, the multi-
channel sound is downmixed to 2 channels.
< In case you experience any problem with the audio output,
read the instructions of the connected component to check
the adaptable format.
If the connected component cannot accept 4% down signal,
set the 4% down mode off.
When playback is stopped, hold down the STOP button for
more than 2 seconds and release it when “i.60958”,
“i.PCM” or “i.OFF” appears on the display.
Each time the STOP button is pressed for 2 seconds, the output
setting changes.
Flow Status
While the display shows “i.60958” or “i.PCM”, repeatedly
press the STOP button to turn ON or OFF the flow status.
When using the i.LINK terminal, select “i.60958” or
“i.PCM”, and set the Digital Output setting to “ON”.
If the component connected via the i.LINK terminal is
compatible with the flow rate control, and if you set the flow
status of the UX-3 ON, the connected component will work in
the flow rate control mode.
i.60958
When the disc is DVD-video/VCD/CD, the digital signal is
output in the format (Stream or PCM) you set in the Audio
Digital Out (see page 37).
< DSD signal is output during playback of a SACD disc, and
linear PCM digital signal during playback of a DVD-Audio
disc.
< Though the flow status function of the UX-3 is not same as
the flow rate control, RAM buffer of the connected
component will absorb clock differences and control the flow
rate using the clock of the connected component.
< In the following cases, set the flow status OFF:
• The connected component isn’t compatible with the flow
rate control.
• Though the connected component is compatible with the
flow rate control, the flow rate control doesn’t work
properly with this unit.
i.PCM
Linear PCM digital signal is output when the disc is DVD-
video/VCD/CD.
Dolby Digital/DTS/MPEG signals are converted into linear
PCM.
When the i.LINK (AUDIO) terminal is connected a component
without a Dolby Digital/DTS/MPEG decoder, select “i.PCM”.
• Sound skips.
< During playback of a video source, the flow status is
automatically set to OFF to keep the synchronization of audio
and video.
< Some amplifiers may regard this signal as DVD-Audio.
< DSD signal is output during playback of a SACD disc, and
linear PCM digital signal during playback of a DVD-Audio
disc.
< When the flow status is set to ON, “i.60958 FL” or “i.PCM
FLOW” will appear on the display instead of “i.60958” or
“i.PCM”.
i.OFF
Select this when you don’t use the i.LINK (AUDIO) terminal.
No signal is output from the i.LINK (AUDIO) terminal.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
i.LINK (IEEE 1394)
The i.LINK is also known as IEEE 1394, an international
specification.
This unit is ready for i.LINK (AUDIO).
How to connect multiple i.LINK-capable
devices
By connecting an i.LINK (AUDIO)-capable device to the IEEE 1394
(or i.LINK (AUDIO) terminal on this unit using an i.LINK cable, you
can transmit SACD multi-channel signals that could not be
transmitted but in analog format in the past can be transmitted
in its original digital format, in addition to the capability of
transmitting 2-ch linear PCM data and multi-channel compressed
audio signals.
Daisy chain connection
You can daisy-chain up to 17 devices including this unit.
i.LINK cable
i.LINK-capable
device
i.LINK-capable
device
i.LINK-capable
device
i.LINK-capable
device
If you have multiple i.LINK-capable devices, you can connect
them through other devices to transmit data between them, so
you don’t need to be concerned with the order of connection.
Connection in tree structure
If you are using a device having three or more i.LINK connectors,
you may want to get the connection branched out. This way of
connection allows you to connect up to 17 devices including this
unit.
Copyright protection system DTCP
i.LINK-capable
device
i.LINK-capable
device
i.LINK-capable
device
To play back audio sounds recorded on SACD or DVD discs using
i.LINK, both the player and the D/A converter need to be ready
for the copyright protection system DTCP (Digital Transmission
Content Protection).
i.LINK-capable
device
i.LINK-capable
device
This unit is ready for DTCP.
Your system does not work if data is fed back to the output
device. Be careful not to create a loop.
Data transfer rate
There are three transfer rates: 100 Mbps (S100), 200 Mbps
(S200), and 400 Mbps (S400). This unit is capable of transferring
data at a maximum 400Mbps.
i.LINK-capable
device
i.LINK-capable
device
i.LINK-capable
device
i.LINK-capable
device
i.LINK-capable
device
i.LINK-capable
device
For connection to an i.LINK-capable device, use a commercially
available S400-compliant 6-pin i.LINK cable.
When connecting multiple i.LINK-capable devices, avoid
connecting a device having slow transfer rate between devices
having high transfer rate since this reduces the transfer rate of
your whole system. Connect devices having high transfer rate
towards the source as far upriver as possible.
The i.LINK interface of this unit is designed in accordance with
the following specifications:
1) IEEE Std 1394a-2000, Standard for a High Performance
Serial Bus
2) Audio and Music Data Transmission Protocol 2.0
NOTES
< Among the i.LINK formats there are “MPEG-2 TS” for BS
digital source and “DV” for digital video for DVD recorders,
as well as the “i.LINK (AUDIO)” (A&M Protocol). Never
connect devices that are not ready for i.LINK (AUDIO) to this
unit. If you do, this unit and others may get out of order or be
damaged.
This unit is compliant with IEC 60958 bitstream, DVD-Audio,
SACD in the AM824 sequence adaptation layers of this
protocol.
The i.LINK logo is a trademark of Sony Corporation, registered in
the U.S. and other countries.
< In the process of data transfer, avoid plugging/unplugging the
i.LINK cables in use or switch on/off the power.
< Among the i.LINK-capable devices there are some that, if not
turned on, are not capable of relaying data.
< Chances are some i.LINK-capable devices will not respond to
this unit's command.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
In case you experience any problem with this unit, please take
Sound skips.
the time to look through this chart and see if you can solve the
problem yourself before you call your dealer.
e Place the unit on a stable place to avoid vibration and shock.
e If the disc is dirty, clean the surface of the disc.
e Don’t use scratched, damaged or warped discs.
No power
e Check the connection to the AC power supply. Check and
make sure the AC source is not a switched outlet and that,
if it is, the switch is turned on. Make sure there is power to
the AC outlet by plugging another item such as a lamp or
fan.
There is no sound or only a very low-level sound is heard.
e Check that the amplifier and speakers are connected
securely.
e Check the operation of the amplifier.
e Check the audio output setting (see page 31).
e When the amplifier is connected via the i.LINK (AUDIO) or
the DIGITAL OUT terminal, set the Digital Out setting to
“ON” (see page 31).
e Press the POWER switch of the main unit to turn it on.
Remote control doesn’t work.
e Press the POWER switch of the main unit to turn it on.
e If the batteries are dead, change the batteries.
e Use remote control unit within the range (5m /15ft) and
point at the front panel.
e The sound is muted during pause, slow-motion, fast
forward/reverse, and stepping playback. Press the PLAY
button to resume normal playback.
e Clear obstacles between the remote control unit and the
main unit.
e If a strong light is near the unit, turn it off.
No multi-channel audio output
e Set the Analog Output setting to “Multi-Channel”, or use
the 2CH/MULTI button of the remote control unit to change
the settings (see page 31).
Severe hum or noise is heard.
e Change the speaker configuration if necessary (see page
36).
e For digital multi-channel output, you must use a multi-
channel surround amplifier, and set the Audio Digital Out
settings to “Stream” (see page 37).
e Place the unit as far away from a TV as possible.
e Make sure the line cords and speaker cables are as far away
from the AC supply as possible.
Will not play.
e SACD and DVD audio discs may have more than one group
or playback area, not all of which contain multi-channel
audio data. Choose another group or playback area (see
page 20).
e Reload the disc with the label side UP.
e This unit cannot play such discs as CD-ROMs. Use a playable
disc (see page 9).
e If the disc is dirty, clean the surface of the disc.
e A blank disc has been loaded. Load a prerecorded disc.
e Check the region code of the DVD (see page 8).
e If the unit is condensed, leave the unit for one or two hours
with the power turned on (see page 43).
Overall volume is low, or balance between speakers is
strange
e A speaker’s level (or that of a pair of speakers) has been set
up too low or too high in the speaker setup (see page 37).
Correct the levels.
PROHIBIT icon “A” appears on the screen.
e The operation is not permitted by the disc or the unit.
e Note that during playback of a title part (cautions, software
maker’s logo, etc.), most operations are prohibited by the
disc.
e When the unit is downmixing multi-channel audio, the
volume differs from the non-downmixed level. Use the
amplifier to adjust the volume.
e When configuring speaker sizes, making “small” and “off”
settings on speakers other than the subwoofer can affect
the subwoofer volume. Adjust the level on the subwoofer
itself (see page 36).
e If another operation is still in process, wait a moment and
try again.
Settings are canceled.
No digital audio output.
e When the power is suddenly cut due to power failure or by
unplugging the power cord, settings will be cancelled. Be
sure to turn the unit off by pressing the POWER switch
before unplugging the power cord.
e
Check that the Digital Out setting is set to “ON” (see page 31).
When using the i.LINK (AUDIO) terminal, set the i.LINK output
setting to “i.60958” or “i.PCM”(see page 42).
e Some DVD-Audio discs prohibit digital audio output.
e Digital audio from a SACD disc cannot be output from the
DIGITAL OUT terminals. Use the i.LINK (AUDIO) terminal.
e No digital audio is output from the DIGITAL OUT terminals
when playing DVD-Audio in multi-channel (other than Dolby
Digital or DTS).
Cannot access some setup menu items.
e Although it is possible to enter the setup screen while
playback is continuing (or in resume mode), not all menu
functions will be available. Expand the number of available
functions by pressing the STOP button twice (see page 30).
Digital audio recording is not possible on another device
e Check that the Digital Out setting is set to “ON”. And the
digital output format must be set to “PCM” (see page 31,
37). Set the Analog Output setting to “2ch”.
Scanning stops.
e Scanning does not work within menus.
e Copy-prohibit material cannot be copied digitally.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Cannot output 96kHz or 88.2kHz digital audio.
e Check that the Audio Digital Out setting is set to “Down
Sample OFF” (see page 37).
DISPLAY button doesn’t work.
No message appear on the screen.
e Set the On Screen Display option to “ON” (see page 40).
e Some copy protected discs do not output high sampling rate
digital audio.
ANGLE mark doesn’t appear on the screen.
e Set both the Angle Indicator option and the On Screen
Display option to “ON” (see page 40).
No DTS audio output.
e When your amplifier is not equipped with DTS decoder, set
the DTS setting to “PCM”. Or press the AUDIO button to
select any other audio (see page 37, 24).
e When playing back a DTS-CD, set the CD Digital Direct
setting to “Normal” (see page 31).
Picture and sound don’t match up.
e Use the lip sync feature to adjust the relative timing of
picture and audio (see page 25).
e Check the setting of your amplifier.
The CLOCK MODE button flashes and the display shows
“No Word!”
Noticeable difference in DVD, CD and SACD’s volume.
e That is because DVDs, CDs and SACDs use different
recording methods.
e The word sync mode is selected, but there is no clock
source. Turn the word sync mode off (see page 27).
e No word clock is being received. Check cables, connections,
and settings of the clock generator.
No picture/distorted picture
e Check the connection to the television (monitor)
e Check the operating instructions for the television (monitor)
to make sure that you have the right input selected, etc.
e Use the VIDEO ON button of the remote control unit to turn
the video on (see page 27).
The CLOCK MODE button flashes and the display shows
“WRD UNLCK!”
e Invalid word sync signal is received. Check the setting of the
clock generator.
e If you are using a DVI-D connection, make sure it is
configured correctly (see page 26).
e If you are using a component or D1/D2 connection, make
sure it is configured correctly (see page 39).
e Make sure that the PAL-NTSC conversion setting matches
the television/monitor.
If normal operation cannot be obtained, unplug the power
cord from the outlet and plug it again. This resets the
internal micro-computer which can be disturbed during
electrical storms, power interruptions, et cetera.
e When your television/monitor isn’t compatible with
Progressive scan, never set the Component Video setting to
“Progressive” (see page 39).
Picture noise.
Beware of condensation
e If video from this system has to go through your VCR to get
to your TV, the copy-protection applied to some DVD
programs could affect picture quality. Please connect the
unit directly to your TV.
When the unit (or a disc) is moved from a cold to a warm
place, or used after a sudden temperature change, there is a
danger of condensation; vapor in the air could condense on
the internal mechanism, making correct operation impossible.
To prevent this, or if this occurs, leave the unit turned on for
one or two hours. Then the unit will stabilize at the
temperature of its surroundings.
The image is distorted or monochromatic.
e The color system selected does not match your TV (see page
7).
e Adjust the aspect ratio to correspond to the
television/monitor in use (see page 38).
e If using an S1/S2 S-Video connection, you may need to set
the output signal to “S1” (see page 38).
Maintenance
If the surface of the unit gets dirty, wipe with a soft cloth or
use diluted neutral cleaning liquid. Be sure to remove any
fluid completely. Do not use thinner, benzine or alcohol as
they may damage the surface of the unit.
The aspect ratio of the screen cannot be changed.
e The aspect ratio might be fixed by the disc.
Screen is suddenly stretched when the Setup screen is
opened.
e If the Setup screen is opened during playback of a DVD
being viewed in the letter box format, the screen may switch
to the wide screen format. This is not a malfunction. The
screen will return to normal when the Setup screen is
closed.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
System . . . . . . . . . . . . . . DVD-Video, DVD-Audio, DVD-R/RW,
Video-CD, SACD, and CD
Audio output (Digital Audio)
OPTICAL . . . . . . . . . . Optical digital jack x 1, –15 to –21 dBm
COAXIAL . . . . . . . . . . . . . . . . . . RCA jack x 1, 0.5 Vp-p/75 Ω
Power supply
Europe model . . . . . . . . . . . . . . . . . . . . . AC 230 V, 50 Hz
U.S.A./Canada model. . . . . . . . . . . . . . . . AC 120 V, 60 Hz
Korea model . . . . . . . . . . . . . . . . . . . . . . AC 220 V, 60 Hz
Word Synchronization input format
Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC
Input level . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 Vp-p/75 Ω
Power consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 W
The main unit can accept and synchronize to the following
frequencies (rectangular wave) received from external devices:
44.1kHz, 48kHz, 88.2kHz, 96kHz, 100kHz, 176.4kHz,
192kHz as well as frequencies which are 96% of these
values, in the 4% DOWN mode.
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.5 kg (51-3/4 lb)
External dimensions (W x H x D). . . . . . . 442 x 153 x 353 mm
(17-3/8˝ x 6˝ x 13-7/8˝)
Operating temperature. . . . . . . . . . . . . . . . . . . . +5˚C - +35˚C
Operating humidity . . . . . . . . . 5% to 85% (no condensation)
Storage temperature. . . . . . . . . . . . . . . . . . . . . –20˚C - +55˚C
Accessories
Power cord x 1
Remote Control Unit (RC-942) x 1
Batteries (AA, R6 or SUM-3) x 2
Screwdriver x 1
Felt x 3
Warranty card x 1
Video Output
S-Video output (S1/S2)
Y (luminance) - Output level . . . . . . . . . . . . . 1 Vp-p (75 Ω)
C (color) - Output level . . . . . . . . . . . . . 286 mVp-p (75 Ω)
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S-VIDEO jack
Owner's manual x 1
Video output
Output level . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack
• Design and specifications are subject to change without
notice.
• Weight and dimensions are approximate.
• Illustrations may differ slightly from production models.
Component video output (Y, PB, PR)
Y-Output level . . . . . . . . . . . . . . . . . . . . . . 1.0 Vp-p (75 Ω)
PB, PR-Output level . . . . . . . . . . . . . . . . . . . 0.7 Vp-p (75 Ω)
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC jacks
D1/D2 video output (Y, PB, PR)
Y-Output level . . . . . . . . . . . . . . . . . . . . . . 1.0 Vp-p (75 Ω)
PB, PR-Output level . . . . . . . . . . . . . . . . . . . 0.7 Vp-p (75 Ω)
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D terminal
353mm
332mm
DVI-D video output (HDCP compatible digital RGB)
Jacks . . . . . DVID 24pin (conform to TMDS, single link only)
Audio output (Analog Audio)
Jacks . . . . . . . . . . . . . . . . . . . . . . . . XLR jacks (2 channel) x 1
RCA jacks (2 channel) x 1
Maximum Output level (1 kHz, full scale)
RCA: 2.5 Vrms (47 kΩ)
XLR: 2.5 Vrms (600 Ω)
Nominal Output level (1 kHz, full scale –20dB)
RCA: 250 mVrms (47 kΩ)
XLR: 250 mVrms (600 Ω)
153mm
Frequency response . . . . . . . . . . . . 5Hz - 80 kHz (DVD-Audio)
Signal-to-Noise Ratio (S/N) . . . . . . . . . . 112 dB (SACD, 1 kHz)
Dynamic range . . . . . . . . . . . . . . . . . . . 106 dB (SACD, 1 kHz)
Total harmonic distortion . . . . . . . . . . 0.001% (SACD, 1 kHz)
Decodable format. . . . . . . . . . . DTS, DTS 96/24, Dolby Digital
PCM 44.1 kHz-192 kHz/16-24 bit, DSD
442mm
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Block Diagram
Spindle
Motor
SACD
CD･VCD
DVD
1394
Transmitter
Optical
Pickup
i.LINK(AUDIO) (IEEE1394)
VRDS UNIT
Driver
RF Amp
–
D/A
Converter
Balanced
Front L ch
+
SACD
SACD
PCM
Decoder
Converter
D/A
Front End
DSP
Front L ch
Converter
Digital
Filter
AUDIO OUT
(2ch)
D/A
Converter
CD
Front R ch
Balanced
Front R ch
+
–
D/A
Converter
DVD
Audio
DSP
MPEG-2
Decoder
Coaxial
Optical
DIGITAL OUT
Composite
Video
Back End
MPU
S-Video
FRONT PANEL
Y
Video
Encoder
Component
Video
I/F
MPU
CB/PB
CR/PR
FL
Display
VIDEO OUT
D1/D2
Key
SW
I/P
Converter
DVI
DVI-D
Transmitter
(HDCP)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan Phone: (0422) 52-5132 e-mail: [email protected]
TEAC ESOTERIC COMPANY
TEAC AMERICA, INC.
7733 Telegraph Road, Montebello, California 90640 Phone: (323) 726-0303
TEAC CANADA LTD.
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada Phone: (905) 890-8008
Campesinos N°184, Colonia Granjas Esmeralda, Delegacion Iztapalapa, CP 09810, México DF Phone: (525) 581-5500
5 Marlin House, Croxley Business Park, Watford, Hertfordshire, WD18 8TE, U.K. Phone: 01923-819699
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany Phone: 0611-71580
TEAC MEXICO, S.A. De C.V
TEAC UK LIMITED
TEAC EUROPE GmbH
TEAC ITALIANA S.p.A.
Via C. Cantù 11, 20092 Cinisello Balsamo, Milano, Italy Phone: 02-66010500
This appliance has a serial number located on the rear panel. Please record
the model number and serial number and retain them for your records.
.
Model number
Serial number
0305 MA-0959A
Download from Www.Somanuals.com. All Manuals Search And Download.
|