Echo Trimmer SHC 225 User Manual

Shaft Hedge Clipper  
Operator's Manual  
MODELS  
SHC-225  
SHC-225S  
WARNING  
Read rules for safe operation and instructions carefully. ECHO provides an  
Operator's Manual and a Safety Manual. Both must be read and understood for  
proper and safe operation. Failure to do so could result in serious injury.  
X750011882  
12/09  
X7502257102  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
3
sa f e t y  
m a n u a l s a f e t y s y m b o l s a n d Im p o r t a n t In f o r m a t Io n  
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre-  
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean  
to you.  
CIRCLE AND SLASH SyMbOL  
DANGER  
This symbol means the specific action  
shown is prohibited. Ignoring these prohi-  
bitions can result in serious or fatal injury.  
The safety alert symbol accompanied by the word  
“DANGER” calls attention to an act or condition  
which WILL lead to serious personal injury or  
death if not avoided.  
NOTE  
WARNING  
This enclosed message provides tips for use, care and  
maintenance of the unit.  
The safety alert symbol accompanied by the word  
WARNING” calls attention to an act or condi-  
tion which CAN lead to serious personal injury or  
death if not avoided.  
IMPORTANT  
The enclosed message provides information neces-  
sary for the protection of the unit.  
CAUTION  
The safety alert symbol accompanied by the word  
“CAUTION” calls attention to an act or condition  
which may lead to minor or moderate personal  
injury if not avoided.  
In t e r n a t Io n a l s y m b o l s  
Symbol  
description/application  
Symbol  
description/application  
Symbol  
description/application  
Symbol  
description/application  
Symbol form/shape  
Symbol form/shape  
Symbol form/shape  
Symbol form/shape  
Plan retreat  
path from falling  
objects.  
Read and under-  
stand Operator's  
Manual.  
Fuel and oil  
mixture  
Emergency stop  
Finger Severing  
Wear eyes, ears  
and head protec-  
tion  
Wear slip resis-  
tant foot wear.  
Primer  
bulb  
Wear hand  
protection. Use  
two handed.  
Carburetor adjust-  
ment  
- High speed  
mixture  
Hot  
Surface  
Ignition  
ON/OFF  
DO NOT smoke  
near fuel.  
Carburetor adjust-  
ment  
Carburetor adjust-  
ment  
Safety/Alert  
- Low speed  
mixture  
- Idle speed  
Avoid all power  
lines. This unit  
is not insulated  
against electrical  
current.  
DO NOT allow  
flames or sparks  
near fuel.  
Choke Control  
"Cold Start"  
Position  
Choke Control  
"Run"  
Position  
(Choke Closed)  
(Choke Open)  
Do not operate  
closer than 15 M  
(50 ft.) from elec-  
Keep bystanders  
at least 15 meters  
(50 feet) away.  
trical  
haz-  
ards.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
p e r s o n a l c o n d It Io n a n d s a f e t y e q u Ip m e n t  
WARNING  
Hedge Clipper users risk injury to themselves and others if the hedge clipper is used improperly and or safety  
precautions are not followed. Proper clothing and safety gear must be worn when operating a hedge clipper.  
Physical Condition  
Proper Clothing  
Your judgment and physical dexterity may not be good:  
• if you are tired or sick,  
Wear snug fitting, durable clothing;  
• Pants should have long legs, shirts with long sleeves.  
• DO NOT WEAR SHORTS,  
• if you are taking medication,  
• if you have taken alcohol or drugs.  
Operate unit only if you are physically and mentally well.  
• DO NOT WEAR TIES, SCARFS, JEWELRY.  
Wear sturdy work shoes with nonskid soles;  
• DO NOT WEAR OPEN TOED SHOES,  
• DO NOT OPERATE UNIT BAREFOOTED.  
Wear no-slip, heavy duty work gloves.  
Keep long hair away from engine and air intake. Retain  
hair with cap or net.  
Eye Protection  
Eye protection that meets ANSI Z87.1 or CE requirements  
must be worn whenever you operate the unit.  
Hand Protection  
Wear no-slip, heavy duty work gloves to improve your  
grip on the handles. Gloves also reduce the transmission of  
machine vibration to your hands.  
Hot Humid Weather  
Heavy protective clothing can increase operator fatigue  
which may lead to heat stroke. Schedule heavy work for  
early morning or late afternoon hours when temperatures  
are cooler.  
Hearing Protection  
Wear hearing protection. ECHO recommends wearing  
hearing protection whenever unit is used.  
Vibration and Cold  
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be  
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen-  
sations, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended,  
because the minimum exposure which might trigger the ailment is unknown.  
• Keep your body warm, especially the head, neck, feet, ankles,  
hands, and wrists.  
• Maintain good blood circulation by performing vigorous arm  
exercises during frequent work breaks, and also by not smoking.  
• Limit the hours of operation. Try to fill each day with jobs where  
operating the unit or other hand-held power equipment is not  
required.  
• If you experience discomfort, redness, and swelling of the fingers  
followed by whitening and loss of feeling, consult your physician  
before further exposing yourself to cold and vibration.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
5
Repetitive Stress Injuries  
It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness,  
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high  
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which  
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged  
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.  
To reduce the risk of RSI/CTS, do the following:  
• Avoid using your wrist in a bent, extended, or twisted position.  
Instead try to maintain a straight wrist position. Also, when grasp-  
ing, use your whole hand, not just the thumb and index finger.  
• Take periodic breaks to minimize repetition and rest your hands.  
• Reduce the speed and force with which you do the repetitive move-  
ment.  
• Do exercises to strengthen the hand and arm muscles.  
• Immediately stop using all power equipment and consult a doctor  
if you feel tingling, numbness, or pain in the fingers, hands, wrists,  
or arms. The sooner RSI/CTS is diagnosed, the more likely perma-  
nent nerve and muscle damage can be prevented.  
DANGER  
Do not operate this product indoors or in inadequately ventilated  
areas. Engine exhaust contains poisonous emissions and can cause  
serious injury or death.  
Read the Manuals  
• Provide all users of this equipment with the Operator’s Manual and  
Safety Manual for instructions on Safe Operation.  
Clear the Work Area  
• Spectators and fellow workers must be warned, and children and  
animals prevented from coming nearer than 15 m (50 ft.) while the  
unit is in use.  
Keep a Firm Grip  
• Hold the front and rear handles with both hands, with thumbs and  
fingers encircling the handles.  
Keep a Solid Stance  
• Maintain footing and balance at all times. Do not stand on slippery,  
uneven or unstable surfaces. Do not work in odd positions or on  
ladders. Do not over reach.  
Avoid Hot Surfaces  
• Keep exhaust area clear of flammable debris. Avoid contact during  
and immediately after operation.  
WARNING  
Never perform blade maintenance procedures while engine is run-  
ning.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
e q u Ip m e n t  
WARNING  
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment com-  
bination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments, or accessories which  
have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and  
safety manual.  
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.  
• Never adjust blades when the engine is operating.  
• Inspect hand guard for damage. Replace if damaged or missing.  
• Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades  
should not be used.  
WARNING  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings.  
ALWAyS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop  
before removing obstructions, clearing debris, or servicing unit.  
DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.  
NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.  
WARNING  
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found,  
do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an autho-  
rized servicing dealer before using.  
em Is s Io n co n t r o l (e x h a u s t & e v a p o r a t Iv e )  
EPA 2010 and Later and/or C.A.R.B. TIER III  
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank  
the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to  
California models only.  
Emission Control Label (located on Engine) (EXAMPLE ONLY, information on label varies by FAMILY).  
PRODUCT EMISSION DURAbILITy (EMISSION COMPLIANCE PERIOD)  
The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis-  
sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as  
listed in the Maintenance Section of this manual.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
7
de s c r Ip t Io n  
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc-  
tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING  
instructions for specific information.  
12  
11  
Hot Decal (near muffler)  
P/N X505002310  
19  
13  
10  
18  
17  
14  
16  
15  
6
5
shc-225  
4
3
1
2
7
8
9
6
5
shc-225s  
4
3
2
1
7
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Hand Guard  
P/N 89018721560  
P/N 89016021560  
P/N X505001930  
1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter.  
2. THROTTLE HANDLE - FOR RIGHT HAND - Contains Stop Switch, Throttle Lockout, and Throttle Trigger.  
3. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is  
prevented unless throttle trigger lockout lever is engaged.  
4. STOP SWITCH - Mounted on top of the Throttle Trigger Housing. Move switch FORWARD to RUN, BACK to  
STOP.  
5. DRIVE SHAFT ASSEMbLy - Contains the Flexible Drive Cable.  
6. SUPPORT HANDLE - FOR LEFT HAND - Adjustable, loop handle for proper cutting attitude and operator  
comfort.  
7. bLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable of cut-  
ting on either side.  
8. GEAR HOUSING ASSEMbLy - Gear housing assembly fixed straight extension.  
9. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, depress gradually  
for best operating technique.  
10. bLADE COVER - Used to cover blade during transport and storage. Remove blade cover before using unit.  
11. SPARK PLUG - Provides spark to ignite fuel mixture.  
12. TOP GUARD - Protects arm from the hot engine.  
13. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALyST -The muffler or  
catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of  
carbon from leaving the muffler. Keep exhaust area clear of flammable debris.  
14. FUEL TANK - Contains fuel and fuel filter.  
15. FUEL TANK CAP - Covers and seals fuel tank opening.  
16. RECOIL STARTER HANDLE - Pull handle slowly until starter engages, then quickly and firmly. When engine  
starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.  
17. PURGE bULb - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from  
the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge  
bulb an additional 4 or 5 times.  
18. CHOKE CONTROL - Located on the air cleaner housing. Move the lever to Cold Start (  
for Cold Starting. Move lever to Run ( ) position after engine fires.  
) to close the choke  
19. AIR CLEANER - Contains replaceable filter element.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
9
co n t e n t s  
The ECHO product you have purchased has been factory pre-assembled for your convenience.  
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing  
parts. Use the contents list to check for missing parts.  
____ 1 - Power Head/Driveshaft/Hedge Clipper Assembly  
____ 1 - Operator's Manual  
____ 1 - Hedge Clipper Safety Manual  
____ 1 - Warranty Registration Card  
____ 1 - Torx T27 L-Wrench (225 Model Only)  
____ 1 - Blade Cover  
as s e m b l y  
225 Model Only  
Tools Required: Torx T27 L-Wrench  
Parts Required: Drive Shaft Assembly and Gear Housing Assembly.  
g e a r h o u s In g a s s e m b l y / d r Iv e s h a f t  
NOTE  
Hedge Clipper Blades are very sharp. Wear gloves to protect hands.  
1. Remove locating bolt (A) and loosen clamping bolt (B).  
2. Remove vinyl cap from drive shaft.  
A
3. Slide Gear Housing Assembly onto Drive Shaft. Be certain the  
Flex Drive Shaft engages the hole in Driver Gear.  
IMPORTANT  
Flat edge of washer (C) must be against drive shaft.  
4. Align locating hole in gear housing with locator hole in drive shaft.  
5. Install locating bolt (A). Tighten clamping bolt (B).  
B
C
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
f r o n t h a n d l e  
MIN  
SPACING  
NOTE  
Label shows minimum spacing for front handle location.  
1. Position front handle in comfortable operating position and  
tighten screws.  
op e r a t Io n  
WARNING  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete  
stop before removing obstructions, clearing debris, or servicing unit.  
WARNING  
Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped with  
a spark arrestor and a spark arrestor may be required. The operator should contact local fire agencies for laws or  
regulations relating to fire prevention requirements.  
f u e l  
NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor  
performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage  
section of this manual.  
WARNING  
Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are  
NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance prob-  
lems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to,  
improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carbu-  
retors and other engine components.  
Fuel Requirements  
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up  
to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alco-  
hol) is NOT approved.  
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards must  
be used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine problems due to  
inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD certified oil, such as  
Echo premium Power Blend X TM, will void the two-stroke engine warranty.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
11  
IMPORTANT  
Echo premium Power Blend X TM Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo en-  
gines sold in the past regardless of ratio specified in those manuals.  
Handling Fuel  
DANGER  
Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.  
• Use an approved fuel container.  
• DO NOT smoke near fuel.  
• DO NOT allow flames or sparks near fuel.  
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.  
• NEVER refuel a unit when the engine is HOT or RUNNING!  
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.  
• DO NOT overfill fuel tank. Wipe up spills immediately.  
• Securely tighten fuel tank cap and close fuel container after refueling.  
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.  
• Move at least 3m (10 ft.) from refueling location before starting the engine.  
Mixing Instructions  
1. Fill an approved fuel container with half of the required amount of  
gasoline.  
2. Add the proper amount of 2-stroke oil to gasoline.  
3. Close container and shake to mix oil with gasoline.  
4. Add remaining gasoline, close fuel container, and remix.  
IMPORTANT  
Spilled fuel is a leading cause of hydrocarbon emissions. Some  
states may require the use of automatic fuel shut-off containers to  
reduce fuel spillage.  
After use  
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return  
unused fuel to an approved fuel storage container.  
Storage - Fuel storage laws vary by locality. Contact your local gov-  
ernment for the laws affecting your area. As a precaution, store fuel in  
an approved, airtight container. Store in a well-ventilated, unoccupied  
building, away from sparks and flames.  
IMPORTANT  
Stored fuel ages. Do not mix more fuel than you expect to use in  
thirty (30) days, ninety (90) days when a fuel stabilizer is added.  
IMPORTANT  
Stored two-stroke fuel may separate. ALWAYS shake fuel con-  
tainer thoroughly before each use.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
s t a r t In g c o l d e n g In e  
WARNING  
Hedge Clipper blades are very sharp. Touching them may lead to  
severe personal injury. Avoid touching blades whenever possible,  
and always wear gloves to protect hands.  
NOTE  
The blade cover is used for transportation and storage. Remove  
blade cover before using the unit.  
WARNING  
The attachment will operate immediately when the engine starts  
and could result in loss of control and possible serious injury.  
Keep movable parts of the attachment off the ground and away  
from objects that could become entangled or thrown.  
1. Stop Switch  
A
Move Stop Switch button away from the STOP position.  
2. Choke  
Move choke (B) to Cold Start (  
3. Purge Bulb  
) position.  
Pump purge bulb (C) until fuel is visible and flows freely in the  
clear fuel tank return line. Pump bulb an additional 4 or 5 times.  
4. Recoil Starter  
Lay the unit on a flat area and keep movable attachment parts clear  
of all obstacles. Firmly grasp throttle handle and throttle trigger  
lockout with left hand and fully depress throttle trigger to wide  
open position. Rapidly pull recoil starter handle/rope (D) until  
engine fires (or maximum five [5] pulls).  
5. Choke  
After engine fires or five (5) pulls, move choke lever back to Run  
B
(
) position. Firmly grasp throttle handle and throttle trigger  
lockout with left hand and fully depress throttle trigger to wide  
open position. Pull starter handle/rope until engine starts and runs.  
Release throttle trigger and allow unit to warm up at idle for several  
minutes.  
C
NOTE  
If engine does not start with choke in Run position after 5 pulls,  
repeat instructions 2 -5.  
D
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
13  
WARNING  
The blades must not move at idle, otherwise serious personal in-  
jury may result. Periodic carburetor adjustment may be necessary  
to assure blades do not move at idle.  
If blades move, readjust carburetor according to “Carburetor Ad-  
justment” instructions in this manual or see your ECHO Dealer.  
6. Throttle Trigger  
After engine warm up, grip throttle handle with right hand and  
support handle with left hand. Depress throttle trigger lockout, and  
gradually depress throttle trigger to increase engine RPM to operat-  
ing speed.  
s t a r t In g w a r m e n g In e  
The starting procedure is the same as Cold Start except DO NOT close  
the choke, and do not depress throttle trigger to wide open position.  
WARNING  
The blades must not move at idle, otherwise serious personal in-  
jury may result. Periodic carburetor adjustment may be necessary  
to assure blades do not move at idle.  
A
If blades move, readjust carburetor according to “Carburetor Ad-  
justment” instructions in this manual or see your ECHO Dealer.  
1. Stop Switch  
Move Stop Switch button (A) away from the STOP position.  
2. Purge Bulb  
Pump purge bulb (C) until fuel is visible and flows freely in the  
clear fuel tank return line. Pump bulb an additional 4 or 5 times.  
3. Recoil Starter  
C
Lay the unit on a flat area and keep movable attachment parts clear  
of all obstacles. Firmly grip throttle handle and throttle trigger lock-  
out with left hand. Rapidly pull recoil starter handle/rope (D) until  
engine fires.  
NOTE  
If engine does not start after 5 pulls, use Cold Start Procedure.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
s t o p p In g e n g In e  
1. Throttle  
Release throttle and allow engine to return to idle before shutting  
A
off engine.  
2. Stop Switch  
Move stop switch button (A) backward to STOP position.  
WARNING  
If engine does not stop when stop switch is moved to STOP posi-  
tion, close choke - COLD START position - to stall engine. Have  
your ECHO dealer repair stop switch before using hedge clipper  
again or serious personal injury may result.  
h e d g e t r Im m In g  
WARNING  
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconscious-  
ness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed  
away from your face and body.  
WARNING  
Hedge Clipper blades are very sharp. Touching them may lead to  
severe personal injury. Avoid touching blades whenever pos-  
sible, and always wear gloves to protect hands.  
1. Always grip throttle handle with right hand and support handle  
with left hand while trimming.  
2. Hold trimmer firmly and squeeze throttle trigger to accelerate  
engine.  
3. Tilt trimmer so cutting teeth are angled slightly toward the hedge  
or shrub and proceed to cut.  
WARNING  
Never remove hands from unit when blades are moving.  
WARNING  
The engine continues running even when the blades have stopped  
due to an obstruction. If this occurs, stop the engine, disconnect  
ignition cable and remove the obstruction.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
15  
ma In t e n a n c e  
WARNING  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete  
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.  
Wear gloves to protect hands from sharp edges and hot surfaces.  
Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will help  
achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an  
ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO  
Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs.  
s k Il l l e v e l s  
Level 1 =  
Level 2 =  
Easy to do. Common tools may be required.  
Moderate difficulty. Some specialized tools may be required.  
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.  
m a In t e n a n c e In t e r v a l s  
SKILL  
LEVEL  
REQ'D  
DAILY OR  
BEFORE  
USE  
3 MONTHS  
OR 90  
HOURS  
MAINTENANCE  
PROCEDURE  
EVERY  
REFUEL  
YEARLY 600  
HOURS  
COMPONENT/SYSTEM  
Air Filter  
Inspect/Clean  
1
1
1
1
1
1
2
2
2
2
2
1
1
1
I / C *  
I / C  
Choke Shutter  
Fuel Filter  
Inspect/Clean  
Inspect  
I *  
I / R *  
R *  
Fuel Cap Gasket  
Fuel System  
Inspect/Replace  
Inspect/Replace  
Inspect/Clean  
Inspect/Clean  
Inspect/Clean/Replace  
Inspect/Clean/Decarbon  
Grease  
I *  
I (4) *  
I / C  
I (4) *  
Spark Plug  
I / C / R *  
Cooling System  
Muffler Spark Arrestor  
Cylinder Exhaust Port  
Drive Shaft  
I / C / R *  
I / C  
I (1)  
Gear Housing  
Blades  
Grease  
I (2)  
Inspect/Clean  
Inspect/Clean  
Inspect/Tighten/Replace  
I / C (3)  
I / C *  
I *  
Recoil Starter Rope  
Screws/Nuts/Bolts  
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN  
IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the  
frequency of required maintenance.  
MAINTENANCE PROCEDURE NOTES:  
(1) Apply POWER BLENDXTM grease every 25 hours of use.  
(2) Apply POWER BLENDXTM grease every 15 - 25 hours of use.  
(3) Inspect blade and clean and sharpen as needed. Lubricate blades periodically during use.  
(4) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.  
* All recommendations to replace are based on the finding of damage or wear during inspection.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
a Ir f I l t e r  
Level 1.  
Tools required: 25 - 50 mm (1 - 2 in.) Cleaning Brush  
Parts required: REPOWERTM AIR & FUEL FILTER KIT.  
1. Close choke (Cold Start Position [  
]). This prevents dirt from  
entering the carburetor throat when the air filter is removed. Brush  
accumulated dirt from air cleaner area.  
2. Remove air filter cover. Brush dirt from inside cover.  
3. Remove air filter and lightly brush debris from filter. Replace filter  
if it is damaged, fuel soaked, very dirty, or the rubber sealing edges  
are deformed.  
4. If filter can be reused, be certain it:  
• Fits tightly in the air filter cavity.  
• Is installed with the original side out.  
5. Install air filter cover.  
NOTE  
Carburetor adjustment may be needed after air filter cleaning/re-  
placement.  
f u e l f I l t e r  
Level 1.  
Tools required: 200 - 250 mm (8 - 10 in.) length of wire with one  
end bent into a hook, clean rag, funnel, and an  
approved fuel container  
Parts required: REPOWERTM AIR & FUEL FILTER KIT.  
DANGER  
Fuel is VERy flammable. Use extreme care when mixing, storing  
or handling, or serious personal injury may result.  
1. Use a clean rag to remove loose dirt from around fuel cap and  
empty fuel tank.  
2. Use the “fuel line hook” to pull the fuel line and filter from the  
tank.  
3. Remove the filter from the line and install the new filter.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
17  
s p a r k p l u g  
Level 2.  
Tools Required: T-Wrench, feeler gauge, soft metal brush  
Parts Required: REPOWERTM Tune-Up Kit  
IMPORTANT  
Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) other-  
wise severe engine damage may occur.  
1. Remove spark plug and check for fouling, worn and rounded  
center electrode.  
2. Clean the plug or replace with a new one. DO NOT sand blast to  
clean. Remaining sand will damage engine.  
0.65 mm  
(0.026 in.)  
3. Adjust spark plug gap by bending outer electrode.  
4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).  
c o o l In g s y s t e m  
Level 2.  
Tools required: T27 Torx L-Wrench, 25 - 50 mm (1 - 2 in.)  
Cleaning Brush,  
Parts Required: None.  
IMPORTANT  
To maintain proper engine operating temperatures, cooling air  
must pass freely through the cylinder fin area. This flow of air car-  
ries combustion heat away from the engine.  
Overheating and engine seizure can occur when:  
• Air intakes are blocked, preventing cooling air from reaching the  
cylinder.  
• Dust and grass build up on the outside of the cylinder. This build  
up insulates the engine and prevents the heat from leaving.  
Removal of cooling passage blockages or cleaning of cooling fins is  
considered “Normal Maintenance.” Any failure attributed to lack of  
maintenance is not warranted.  
B
A
1. Remove spark plug lead.  
2. Remove air cleaner cover (A).  
3. Remove 2 engine cover screws and engine cover (B).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
IMPORTANT  
DO NOT use a metal scraper to remove dirt from the cylinder fins.  
4. Remove ignition wires from clip for cleaning.  
5. Use brush to remove dirt from the cylinder fins.  
6. Remove grass and leaves from the grid between the recoil starter  
and fuel tank.  
7. Assemble components in reverse order.  
e x h a u s t s y s t e m  
Spark Arrestor Screen  
Level 2.  
Tools Required: T27 Torx L-Wrench, Soft Metal Brush  
Parts Required: Screen, Gasket  
1. Remove spark plug lead from spark plug, and remove engine cover  
(2 screws).  
2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from  
entering cylinder.  
3. Remove spark arrestor screen cover (C), gasket (D), and screen  
(E), from muffler body.  
E
D
4. Clean carbon deposits from muffler components.  
NOTE  
C
When cleaning carbon deposit, be careful not to damage the cata-  
lytic element inside muffler.  
5. Replace screen if it is cracked, plugged, or has holes burned  
through.  
6. Install engine cover and attach spark plug lead.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
19  
Exhaust Port Cleaning  
Level 2.  
Tools required:  
Torx T27 L-Wrench, Wood or plastic scraper  
Parts Required: As needed: Heat Shield  
1. Remove spark plug lead from spark plug, and remove engine cover  
(2 screws).  
A
B
2. Place piston at top dead center. Remove muffler (A) and heat  
shield (B).  
3. Use a wood or plastic scraping tool to clean deposits from cylinder  
exhaust port.  
IMPORTANT  
Never use a metal tool to scrape carbon from the exhaust port.  
Do not scratch the cylinder or piston when cleaning the exhaust  
port. Do not allow carbon particles to enter the cylinder.  
4. Inspect heat shield, and replace if damaged.  
5. Install heat shield and muffler.  
6. Tighten muffler mounting bolts (or nuts) to 80-95 in•lbf  
(90-110 kgf•cm).  
7. Install engine cover and attach spark plug lead.  
8. Start engine, and warm to operating temperature.  
9. Stop engine, and re-tighten mounting bolts (or nuts) to specifica-  
tions.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
c a r b u r e t o r a d j u s t m e n t  
Engine Break-In  
New engines must be operated a minimum duration of two tanks of fuel  
break-in before carburetor adjustments can be made. During the break-  
in period your engine performance will increase and exhaust emissions  
will stabilize. Idle speed can be adjusted as required.  
High Altitude Operation  
This engine has been factory adjusted to maintain satisfactory starting,  
emission, and durability performance up to 1,100 feet above sea level  
(ASL) (96.0 kPa). To maintain proper engine operation and emission  
compliance above 1,100 feet ASL the carburetor may need to be ad-  
justed by an authorized ECHO service dealer.  
IMPORTANT  
If the engine is adjusted for operation above 1,100 feet ASL, the  
carburetor must be re-adjusted when operating the engine below  
1,100 feet ASL, otherwise severe engine damage may result.  
Level 2.  
Tools required: Screwdriver, Tachometer (ECHO P/N  
99051130017).  
Parts required: None.  
NOTE  
Every unit is run at the factory and the carburetor is set in compli-  
ance with emission regulations. Carburetor adjustments, other than  
idle speed, must be performed by an authorized ECHO dealer.  
1. Check idle speed and reset if necessary. If a tachometer is avail-  
able, idle speed screw (A) should be set to the specifications found  
on page 26 "Specifications" of this manual. Turn idle screw (A)  
clockwise to increase idle speed; counter clockwise to decrease  
idle speed.  
A
WARNING  
When carburetor adjustment is completed, the cutting attachment  
should not move at idle, otherwise serious personal injury may  
result.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
21  
l u b r Ic a t Io n  
Blades  
Level 1.  
Tools Required: Clean rag, cleaning brush, oil can  
Parts Required: 20W Engine Oil (lubrication), 50-50 mixture of  
kerosene and 20W oil (cleaning)  
WARNING  
Hedge Clipper blades are very sharp. Touching them may lead to  
severe personal injury. Avoid touching blades whenever possible,  
and always wear gloves to protect hands.  
1. Brush loose debris from blade and coat both sides of blade with the  
50-50 cleaning mixture.  
2. Allow cleaning mixture to soften the remaining gummy residue  
then wipe it from the blade.  
3. Apply clean oil to the entire length of the blade. Be certain the  
blade bolts are lubricated.  
4. Wipe excess oil from the blade before putting the unit back in ser-  
vice.  
Gear Case  
Level 2.  
Tools required:  
Parts required:  
Grease gun with Lithium Grease, clean rag  
POWER BLENDXTM 14 oz. cartridge or Lithium  
Based Grease  
1. Clean dirt from grease fitting (A).  
2. Carefully pump grease in fitting (A). DO NOT force grease.  
Too much pressure will force grease past seals and cause damage.  
Apply 1-2 pumps of grease every 15-25 hours of operation.  
A
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
Drive Shaft Assembly  
Level 1.  
NOTE  
Hedge Clipper drive shaft should be greased every 25 hours of  
operation.  
Tools required:  
Parts required:  
Torx T27 L-Wrench, screwdriver, clean rag, small  
brush  
POWER BLENDXTM 14 oz. cartridge or Lithium  
Based Grease  
WARNING  
A
Hedge Clipper blades are very sharp. Touching them may lead to  
severe personal injury. Avoid touching blades whenever possible,  
and always wear gloves to protect hands.  
1. Remove gear housing locating screw (A) and clamping screw (B).  
Remove the gear housing assembly from the drive shaft housing.  
B
D
2. Pull the drive shaft (C) from the housing, wipe clean and re-coat  
with a thin coating [1/2 oz. (15 ml)] of grease.  
C
3. Slide the drive shaft back in the drive housing being careful not to  
get dirt on the flex shaft.  
4. Install the gear housing assembly.  
IMPORTANT  
Flat edge of washers (D) must be against drive shaft.  
s h a r p e n In g b l a d e s  
Level 2.  
Tools required: Flat file, screwdriver  
Parts required: None  
WARNING  
Hedge Clipper blades are very sharp. Touching them may lead to  
severe personal injury. Avoid touching blades whenever possible,  
and always wear gloves to protect hands.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
23  
1. Disconnect spark plug wire from spark plug.  
2. Slide blades to allow file clearance using slots (A) on bottom of  
blades. Do not pry against cutting edges.  
3. Follow the original shape, and file each cutting edge carefully to  
avoid damage to adjacent teeth. Maintain 6 mm (.25 in.) radius at  
base of each tooth.  
A
A
IMPORTANT  
If a power grinder is used, DO NOT allow blade to over heat.  
4. Lubricate blades. See "Lubrication".  
5. Connect spark plug wire.  
b l a d e a d j u s t m e n t  
Level 2.  
Tools Required: 8 mm Socket & Extension, 4mm Hex Wrench w/  
extension  
1. Move stop switch to STOP position.  
2. Disconnect spark plug wire.  
WARNING  
Hedge clipper blades are very sharp. Touching them may lead to  
severe personal injury. Use long hex wrenches and sockets with  
extensions when tightening blade screws and blade locknuts to keep  
hands at a safe distance from sharp blades.  
A
B
3. Tighten blade screws (A) securely.  
4. Hold blade screws (A) to prevent turning, and tighten locknuts (B).  
A
B
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
tr o u b l e s h o o t In g  
ENGINE PROBLEM TROUBLESHOOTING CHART  
Status Cause  
Problem  
Check  
Remedy  
Clean or replace  
Fuel at carburetor  
No fuel at carburetor Fuel strainer clogged  
Fuel line clogged  
Clean or replace  
Carburetor  
See your Echo dealer  
Fuel at cylinder  
No fuel at cylinder  
Carburetor  
See your Echo dealer  
Muffler wet with fuel Fuel Mixture too rich  
Open choke  
Engine  
cranks -  
starts hard/  
doesn't  
start  
Clean/replace air filter  
Adjust carburetor  
See your Echo dealer  
Spark at end  
of plug wire  
No spark  
No spark  
Stop switch off  
Electrical problem  
Interlock switch  
Turn switch to ON  
See your Echo dealer  
See your Echo dealer  
Spark at plug  
Spark gap incorrect  
Covered with carbon  
Fouled with fuel  
Adjust to .65mm (0.026 in.)  
Clean or replace  
Clean or replace  
Plug defective  
Replace plug  
Air filter  
Air filter dirty  
Normal wear  
Clean or replace  
Fuel filter  
Fuel filter dirty  
Contaminants/residues in Replace  
fuel  
Fuel vent  
Fuel vent plugged  
Contaminants/residues in Clean or replace  
fuel  
Engine runs,  
but dies or  
does not  
accelerate  
properly  
Spark Plug  
Carburetor  
Plug dirty/worn  
Normal wear  
Clean and adjust or replace  
Improper adjustment Vibration  
Adjust  
Clean  
Cooling System  
Cooling system  
dirty/plugged  
Extended operation in  
dirty/dusty locations  
Spark Arrestor  
Screen  
Spark arrestor  
screen plugged  
Normal wear  
Replace  
Engine does  
not crank  
N/A  
N/A  
Internal engine problem  
See your Echo dealer  
DANGER  
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by ground-  
ing spark plug near cylinder plug hole, otherwise serious personal injury may result.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
25  
st o r a g e  
WARNING  
During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area  
clear of flammable debris during transportation or when storing, otherwise serious personal injury may result.  
Long Term Storage (over 30 days)  
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte-  
nance which includes the following:  
1. Store unit in a dry, dust free place, out of the reach of children.  
WARNING  
Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid touching blades  
whenever possible, and always wear gloves to protect hands.  
DANGER  
Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark, otherwise serious  
personal injury may result.  
2. Place the stop switch in the “OFF” position.  
3. Remove accumulation of grease, oil, dirt and debris  
from exterior of unit.  
8. Drain the fuel tank completely and pull the recoil  
starter handle several times to remove fuel from the  
carburetor.  
4. Perform all periodic lubrication and services that are  
required.  
9. Remove the spark plug and pour 7cc (1/4 oz.) of  
fresh, clean, two-stroke engine oil into the cylinder  
through the spark plug hole.  
5. Apply clean oil to the entire length of the blade. Be  
certain the blade bolts are lubricated.  
A. Place a clean cloth over the spark plug hole.  
B. Pull the recoil starter handle 2-3 times to  
distribute the oil inside the engine.  
C. Observe the piston location through the spark  
plug hole. Pull the recoil handle slowly until the  
piston reaches the top of its travel and leave it  
there.  
6. Install blade cover on blades.  
7. Tighten all the screws and nuts.  
10. Install the spark plug (do not connect ignition cable).  
IMPORTANT  
Always store and transport hedge clippers in a stable, horizontal position. Support gear case and cutting blades to  
prevent excessive flexing, which may cause damage to these components. Always install blade cover when transport-  
ing or storing unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
sp e c If Ic a t Io n s  
MODEL ---------------------------------------------------- SHC-225, SHC-225S  
Length (SHC-225) --------------------------------------- 1758 mm (69.21 in.)  
Length (SHC-225S) -------------------------------------- 1480 mm (58.27 in.)  
Width (SHC-225) ----------------------------------------- 246 mm (9.69 in.)  
Width (SHC-225S)---------------------------------------- 246 mm (9.69 in.)  
Height (SHC-225) ----------------------------------------- 290 mm (11.4 in.)  
Height (SHC-225S)---------------------------------------- 290 mm (11.4 in.)  
Weight (dry) (SHC-225) ---------------------------------- 6.21 kg (13.7 lb.)  
Weight (dry) (SHC-225S) -------------------------------- 6.03 kg (13.3 lb.)  
Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine  
Bore---------------------------------------------------------- 32.2 mm (1.27 in.)  
Stroke-------------------------------------------------------- 26.0 mm (1.02in.)  
Displacement ----------------------------------------------- 21.2 cc (1.29 cu. in.)  
Exhaust------------------------------------------------------ Spark arrestor muffler or spark arrestor muffler with catalyst  
Carburetor--------------------------------------------------- Zama Diaphragm w/Purge Pump  
Ignition System -------------------------------------------- Flywheel Magneto, CDI (capacitor discharge ignition) with ESG  
Spark Plug -------------------------------------------------- NGK BPM-8Y (Gap 0.65 mm (0.026 in.)  
Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil)  
Fuel/Oil Ratio ---------------------------------------------- 50 : 1 Power Blend X™ ISO-L-EGD (ISO/CD 13738) and  
J.A.S.O. M345- FC/FD, two-stroke, air-cooled engine oil.  
Gasoline----------------------------------------------------- Use 89 Octane unleaded. Do not use fuel containing methyl  
alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use  
alternative fuels such as E-15 or E-85.  
Oil------------------------------------------------------------ Power Blend X TM Premium Universal 2-Stroke Oil  
Fuel Tank Capacity ---------------------------------------- 0.44 lit. (14.9 US fl. oz.)  
Recoil Starter System ------------------------------------- Automatic Recoil Starter  
Clutch-------------------------------------------------------- Centrifugal Type  
Gear Case Ratio ------------------------------------------- 4.27:1  
Cutter ------------------------------------------------------- Double Reciprocating Blade - Double Edge  
Length----------------------------------------------------- 528 mm (20.79 in.)  
Pitch ------------------------------------------------------- 35 mm (1.38 in.)  
Maximum Diameter Cut  
Soft Material ---------------------------------------------- 25.4 mm (1 in.)  
Woody Material------------------------------------------- 13 mm (1/2 in.)  
Idle Speed--------------------------------------------------- 2,500 - 3,000 RPM  
Clutch Engagement Speed-------------------------------- 4,100 RPM  
Wide Open Throttle Speed ------------------------------- 10,600 - 11,600 RPM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
27  
wa r r a n t y st a t e m e n t s  
ECHO LIMITED WARRANTY STATEMENT FOR  
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010  
ECHO'S RESPONSIBILITY  
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.  
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product  
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED  
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL  
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair  
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any  
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty  
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.  
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers  
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.  
OWNER’S RESPONSIBILITY  
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COM or by fill-  
ing out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct  
link if we find it necessary to contact you.  
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the  
operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your ECHO unit to an authorized ECHO servicing  
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been  
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO  
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you  
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.  
PRODUCT WARRANTY PERIOD  
RESIDENTIAL APPLICATION  
5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for five (5) years from  
date of purchase.  
EXCEPTIONS:  
For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts, and TC tines  
are warranted for the life* of the product on parts only.  
Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for residential or non-income  
producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product  
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.  
ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s  
manual for string head installation and maintenance instructions.  
All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are  
designed to fit.  
COMMERCIAL APPLICATION  
1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income  
producing use will be covered by this limited warranty for one (1) year from the date of purchase.  
2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this  
limited warranty for two (2) years from the date of purchase.  
EXCEPTIONS:  
For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts and TC tines,  
are warranted for the life* of the product on parts only.  
Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for commercial, institutional,  
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period  
of 30 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by  
this warranty.  
ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s  
manual for string head installation and maintenance instructions.  
All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are  
designed to fit.  
RENTAL APPLICATION - 90 DAYS WARRANTY  
• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase.  
*
ECHO’s liability under the “Lifetime” coverage is limited to furnishing parts specified under the PROdUCT wARRANTy PERIOd section of  
this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s final production.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
28  
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES  
• 90-day residential, or non-income producing warranty  
• 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty  
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS  
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior  
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD  
13738 and JASO M345/FC/FD Standards. ECHO Power Blend™ Two-Stroke Oil is a premium two-stroke oil specifically formulated to meet  
ISO-L-EGD (ISO/CD 13738) and JASO M345/FC/FD Standards. The use of two-stroke oils designed for other applications, such as for outboard  
motors or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.  
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:  
Lack of lubrication or engine failure, due to the use of two-stroke oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345/  
FC/FD Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345/FC/  
FD registered oil, will void the two-stroke engine limited warranty. ECHO Power Blend™ Two-Stroke Oil meets the ISO-L-EGD and JASO  
M345/FC/FD Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke  
oil used, per the statement listed in the EPA or California Emission Defect Warranty Explanation.  
damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use gasoline which  
contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/tertiary/butyl/ether)  
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.  
Engine damage caused by use of ether or any starting fluids.  
damage caused by tampering with engine speed governor or emission components, or running engines above specified and recommended  
engine speeds as listed in your operator’s manual.  
Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter.  
damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.  
defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, or use  
of unauthorized attachments.  
Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the operator's  
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.  
Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized ECHO servicing dealer during the  
warranty period.  
Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.  
Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's  
Manuals.  
Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark arrester  
screen.  
Adjustments after the first (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment.  
damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure to comply  
with recommended grease or oil change intervals.  
damage caused by loading SHREd 'N' VAC® beyond recommended capacity.  
damage caused by pump or sprayer running dry, pumping or spraying caustic or flammable materials, or lack of or broken strainers.  
Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational problem or  
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.  
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting  
WWW.ECHO-USA.COM. your receipt of purchase including date, model and serial number must be maintained and presented to an authorized  
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long  
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so you may also have other specific legal rights which vary from state to state. This limited warranty is given by ECHO  
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.  
DISCLAIMER OF IMPLIED WARRANTIES  
This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR PURPOSE  
OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO and its affiliated companies shall not be  
liable for any special incidental or consequential damage, including lost profits. There are no warranties extended other than as provided herein.  
This limited warranty may be modified only by ECHO.  
99922201032  
12/03/09  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
29  
ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT  
FOR ECHO AND SHINDAIWA BRANDS  
The Environmental ProtectionAgency (EPA) and the CaliforniaAir Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased  
to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be  
designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc. must warrant the emission control system on  
your equipment/SORE for the periods of time listed below, provided there has been no abuse, neglect or improper maintenance of your equipment/  
SORE. Your emission control system may include parts such as: carburetor, fuel-injection system, ignition system, catalytic converter/muffler, fuel  
tank, fuel feed lines, fuel cap assembly, spark plug, air filters, and other associated components. Where a warrantable condition exists, ECHO  
Inc will repair your equipment/SORE at no cost to you including diagnosis, parts and labor. The Emission Control System warranty is extended  
to the original owner including all subsequent owners.  
MANUFACTURER'S WARRANTY COVERAGE:  
The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part  
on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative.  
OWNER'S WARRANTY RESPONSIBILITIES:  
As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO  
Inc. recommends that you retain all receipts covering maintenance on your equipment/SORE however, ECHO Inc. cannot deny warranty solely  
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the equipment/SORE owner, you should be  
aware that ECHO Inc. may deny you warranty coverage if your equipment/SORE or a part has failed due to abuse, neglect, improper maintenance  
or unapproved modifications.  
You are responsible for presenting your equipment/SORE to an ECHO Inc. authorized service representative as soon as a problem exists. The  
warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If a warrantable condition exists and there is no  
Authorized Dealer within 100 miles, ECHO Inc. will pay to ship the unit to the nearest authorized dealer. If you have questions regarding your  
warranty coverage, you should contact ECHO Inc. at 1-800-673-1558, web site WWW.ECHO-USA.COM or contact Shindaiwa at 1-877-986-  
7783, web site WWW.SHINDAIWA.COM.  
WHAT DOES THIS WARRANTY COVER?  
ECHO Inc. warrants that your equipment/SORE was designed, built and equipped to conform with applicable EPA and C.A.R.B. emissions  
standards and that your equipment/SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable  
requirements for 2 years or the length of the ECHO Inc. warranty, whichever is longer. The warranty period begins on the date the product is  
purchased by an end user.  
HOW WILL A COVERED PART BE CORRECTED?  
If there is a defect in a part covered by this warranty, any ECHO Inc. Authorized Service Dealer will correct the defect. You will not have to pay  
anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by the dealer. In  
addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.  
WHAT PARTS ARE COVERED?  
Any applicable emission related part not scheduled for "required maintenance" will be repaired or replaced within the warranty period. The repaired  
or replaced part will be warranted for the remaining ECHO Inc. warranty period.  
Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated  
above. Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc. warranty period.  
Any emission related part scheduled for replacement during "required maintenance" is warranted for the period of time prior to the first scheduled  
replacement point for that part. Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the  
first scheduled replacement point for that part.  
Any manufacturer-approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts,  
and must be provided without charge if the part is still under warranty.  
Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce  
the warranty obligations of the manufacturer.  
Throughout the equipment/SORE warranty period, ECHO Inc. will maintain a supply of warranted parts sufficient to meet the expected demand  
for such parts.  
SPECIFIC EMISSION RELATED WARRANTED PARTS:  
• Electronic Ignition System  
• Catalytic Converter / Muffler Assembly  
• Choke  
• Spark Plug  
• Carburetor (complete assembly or replaceable components)  
• Fuel-Injection Assembly (or replaceable components)  
• Fuel Cap Assembly  
• Fuel Tank  
• Air Filter  
• Fuel Feed Line (and associated clamps/connectors as applicable)  
WHAT IS NOT COVERED?  
Any failure caused by abuse, neglect, improper maintenance, unapproved modifications, use of unapproved add-on parts/modified parts or  
unapproved accessories.  
99922201033  
01/2010  
This Emission Control Warranty is valid only for the U.S.A., it's Territories, and Canada.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
30  
NOTES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
He d g e Cl ip p e r  
Op e r a t O r 's Ma n u a l  
31  
NOTES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
se r v Ic In g In f o r m a t Io n  
p a r t s /s e r Ia l n u m b e r  
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies  
for your ECHO products are available only from an Authorized ECHO  
Dealer. When you do need to buy parts always have the Model Num-  
ber, Type and Serial Number of the unit with you. You can find these  
numbers on the engine housing. For future reference, write them in the  
space provided below.  
Model No. _________________SN. ___________________  
s e r v Ic e  
Service of this product during the warranty period must be performed  
by an Authorized ECHO Service Dealer. For the name and address of  
the Authorized ECHO Service Dealer nearest you, ask your retailer or  
call: 1-800-432-ECHO (3246). Dealer information is also available on  
our Web Site. When presenting your unit for Warranty service/repairs,  
proof of purchase is required.  
DEALER?  
Call  
1-800-432-ECHO  
1-800-432-3246  
or  
e c h o c o n s u m e r p r o d u c t s u p p o r t  
If you require assistance or have questions concerning the applica-  
tion, operation or maintenance of this product you may call the ECHO  
Consumer Product Support Department at 1-800-673-1558 from 8:30  
am to 4:30 pm (Central Standard Time) Monday through Friday. Before  
calling, please know the model and serial number of your unit.  
CONSUMER PRODUCT  
SUPPORT  
1-800-673-1558  
8:30 - 4:30 Mon - Fri C.S.T.  
w a r r a n t y r e g Is t r a t Io n  
To ensure trouble free warranty coverage it is important that you regis-  
out the warranty registration card supplied with your unit. Registering  
your product confirms your warranty coverage and provides a direct  
link between you and ECHO if we find it necessary to contact you.  
a d d It Io n a l o r r e p l a c e m e n t m a n u a l s  
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo-  
usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the  
ECHO Web Site for updated information.  
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.  
ECHO, INCORPORATED  
400 Oa k w O O d RO a d  
La k e Zu R ic h , iL 60047  
S85411001144/S85411999999  
S85312002871/S85312999999  
(S) S86111001677/S86111999999  
(S) S86012006190/S86012999999  
Download from Www.Somanuals.com. All Manuals Search And Download.  

FEIN Power Tools Drill ABS 14V User Manual
FieldServer Computer Drive FS 8700 60 User Manual
First Alert Home Security System FA145C User Manual
Focal Car Speaker 130 CVX User Manual
Fujitsu Laptop S 4572 User Manual
Fujitsu Network Card MB86617A User Manual
Fujitsu Server BX960 S1 User Manual
GE Air Conditioner AET05 User Manual
Gefen Switch 6x2 HDMI User Manual
GE Food Warmer 168996 User Manual