110 Dual Fuel
Users Guide
Installation & Service Instructions
U102110-07
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Hotplate Burners
Page 4
Page 5
The Griddle
The Wok cradle
The Grill
Page 6
Page 7
The Ovens
Page 8
The Left Hand Oven
Page 8
The Right Hand Oven
The Clock
Page 8
Page 9
Both Ovens
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 21
Page 22
Page 24
Page 26
Page 32
Page 37
Page 38
Multi-function oven
Handyrack
Oven shelves
Storage
Multi-function Oven cooking guide
Oven Cooking chart
Cleaning your cooker
Moving your cooker
Troubleshooting
General Safety Instructions
Installation
Conversion to LP gas
Circuit Diagram
Technical Data
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Hotplate Burners
Avoid using unstable and misshapen pans that may tilt
easily and pans with a very small base diameter e.g. milk
pans, single egg poachers. The minimum pan diameter
recommended is 120mm (about 43/4").
The drawing by each knob indicates which burner that
knob controls.
Push in and turn a knob to the large flame symbol ( )
and press the igniter button or light with a match.
The Wok burners are designed to provide even heat over
a large area. They are ideal for large pans and stir frying.
For heating smaller pans the smaller burners may be
more efficient.
Adjust the flame height to suit by turning the knob. On
this cooker the low position is beyond high, not between
high and off. The small flame marks the ‘low position’.
Turn the knob towards it after the contents of a pan have
boiled.
When ignition button knob is pressed in,
sparks will be made at every burner, this is
normal.
If after lighting, a hotplate burner’s flame goes
out, turn it off and leave it for one minute before
relighting it.
You can remove the burner cap and trim
rings for cleaning, see pages 18/19.
You should wipe the enamel top surface of the
cooker around the hotplate burners as soon as
possible after spills occur. Try to wipe them off
while the enamel is still warm.
Make sure flames are under the pans. Using a lid will
help the contents boil more quickly.
Pans and kettles with concave bases or down turned
base rims should not be used.
Avoid using unstable and misshapen pans,
which may tilt easily, and pans with a very small
base diameter, e.g. milk pans, single egg
poachers.
The minimum pan diameter recommended is
120mm (43/4"). Smaller pans will be unstable.
Pans and kettles with down turned base rims
should not be used.
Simmering aids, such as asbestos or mesh mats, are
NOT recommended. They will reduce burner
performance and could damage the pan supports.
Note:
Use of aluminium pans may cause metallic
marking of the pan supports. This does not
affect the durability of the enamel and may be
cleaned off with a metal cleaner such as
'Brasso'.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
The Griddle
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. The
controls can be turned to a lower position simply by
turning the control knobs towards the lower position
marked with the small flame symbol.
The griddle fits the centre left pan support, front to back.
It is designed for cooking food on directly. Don’t use pans
of any kind on it. The griddle surface is non-stick and
metal cooking utensils (e.g. spatulas) will damage the
surface. Use heat resistant plastic or wooden utensils.
Always leave space around the griddle for the gases to
escape. Never fit two griddles side by side. Large pans
should also be spaced well apart.
Don’t put it crossways - it will not fit properly and will be
unstable.
Don’t put it on the Wok burners - it is not designed to fit
the Wok burner pan supports.
Use the following heat settings as a guide for
griddle cooking.
High/medium:
Drop scones, Bacon, Chops, Steak, Burgers.
Medium/low:
Position the griddle over the hotplate burners resting on
the pan support.
Potato cakes, Eggs, Fish cakes.
Check that it is securely located.
Experience will soon familiarise you with the
correct setting to use for cooking.
After cooking allow the griddle to cool before
cleaning.
Don’t put it on a Wok burner - it is not designed
to fit the Wok burner pan supports.
The griddle can be lightly brushed with cooking oil before
use. Light the hotplate burners. Adjust the flame heights
to suit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Wok cradle
Make sure the cradle is stable and that the Wok is sitting
level in the ring.
The Rangemaster Wok cradle is designed to fit a
TyphoonTM Professional 14” Wok.
This is available from CookCraft (www.cookcraft.com)
and also from other retailers.
The cradle will get very hot in use - allow plenty of
time for it to cool before you pick it up.
Care and Cleaning
Essential information
If you use a different Wok make sure that it fits the cradle.
Woks vary very widely in size and shape. It’s important
that the Wok sits down on the pan support - but if the
Wok is too small the cradle will not support it properly.
Never use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine
based bleach cleaners, coarse abrasives or salt.
Recommended cleaning materials are hot soapy
water, a moistened soap pad, cream cleaner or
a nylon scourer.
The cradle should be used on the triple ring Wok burner
only.
When you fit the cradle check that the Wok is properly
located on the front and rear fingers and that it is
supported properly on a pan support.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grill
CAUTION: Accessible parts may be hot when
the grill is in use. Young children should be
kept away.
5
The grill pan grid can be turned over to give two grilling
positions.
Remove the pan from the bottom of the grill
compartment.
Don’t leave the grill on for more than a few
moments, without the grill pan underneath it.
For best results, especially with toast,
preheat the grill with the grill pan in the
cooking position for two minutes before use.
After placing your food on the grill tray pan, slide the grill
pan onto the side supports just below the elements. Make
sure it is pushed right in and touches the backstop.
The grill trivet can be removed and the food
placed on it while you are waiting for the grill to
preheat.
The grill pan grid can be turned over to give
two grilling positions.
You can brown the top of dishes cooked in the
oven, under the grill by placing the dish onto the
base of the grill pan, which can easily slide
along the floor of the grill cavity.
The grill has two elements that allow either the whole
area of the pan to be heated or just the right hand half.
Turn the knob to position 3.
For best results preheat for 2 minutes with the grill pan in
position. After placing your food on the grill pan grid, slide
the grill pan onto the side supports. Adjust the heat to suit
by turning the knob.
Make sure it is pushed right in and touches the back
stop.
Never close the grill door when the grill is on.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The Ovens
During use the appliance becomes hot. Care should be taken to avoid the touching heating
elements inside the oven.
The clock must be set to the time of day before the ovens will work. See ‘The Clock’ section for
instructions on setting the time of day.
The Left Hand Oven
The Right Hand Oven
The left hand oven is a Multi-function oven. As well as
the oven fan and fan element, it is fitted with two extra
heating elements, one visible in the top of the oven and
the second under the oven base. Take care to avoid
touching the top element and element deflector when
placing or removing items from the oven. For more detail
on this oven see the section ‘Multi-function oven’.
The fan in the right hand oven circulates hot air
continuously, which means faster more even cooking.
The recommended cooking temperatures for a fanned
oven are generally lower than a non-fanned oven.
The right hand fan oven control is at the right hand end of
the control panel.
The Multi-function oven has two controls, a function
selector and a temperature setting knob.
Turn the oven temperature knob to the temperature you
need.
Turn the function selector control to a cooking function.
The neon light above the control will come on.
The oven indicator light will glow until the oven has
reached the temperature you selected. It will then cycle
on and off during cooking.
Turn the oven temperature knob to the temperature you
need.
The oven indicator light will glow until the oven has
reached the temperature you selected. It will then cycle
on and off during cooking.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
You can turn the knob back to the ( ) manual
setting to keep an eye on the time of day or
leave it in the ( ) minute minder position as the
time ticks down.
The Clock
Setting the time of day
To stop the beeper when it sounds
Turn the Adjusting knob anticlockwise
To stop automatically
Use when you have started the oven manually.
Turn the Timer knob to the ( ) position. Use
the adjustment knob to set the time you need as
below.
When the clock is first connected the display will
flash (
To set the clock to read the time of day turn and
hold the Timer knob to the clock symbol (
) and (
) alternately.
)
and at the same time turn the Adjusting knob left
or right until the clock shows the time of day.
Remember this is a 24 hour clock. Let go of the
Timer knob and it will spring back to the vertical
( ) oven manual setting.
‘Stop Time’ shows. AUTO will show in the
display. Turn the Timer knob to the (AUTO)
setting. When your cooking is finished the
beeper sounds. Turn the Timer knob to the
vertical ( ) to return to manual cooking.
To time something that’s cooking
(minute minder)
To start and stop the oven
automatically
Before you set the clock, you must have two
numbers clearly in mind.
The ‘cook time’, which is the period of time you
want the oven to cook.
The ‘stop time’, which is the time of day you
want the oven to stop cooking.
Turn the Timer knob to the right to the ( )
minute minder setting - it should click into
position. Use the adjustment knob to set the
time you need as below
You cannot set a start time directly - this is set
automatically by setting the cooking period and
stop time.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
To activate the key lock
Turn the Timer knob to the ( ) position. Use
the Adjusting knob to set the ‘cooking time’ you
need as below.
Turn and hold the Timer knob to the clock
symbol ( ) for about 8 seconds. ‘On’ will
appear on the display.
Turn the Timer knob to the ( ) position. The
display will show the current time of day plus the
‘cook period’ you just set. Use the adjustment
knob to set the ‘Stop time’ you need as below.
Keep holding the Timer knob turned to the clock
symbol ( ) and turn the Adjusting knob
clockwise until the key symbol ( ) and ‘Of’ shows
on the display. Let go of the knobs.
‘Stop Time’ shows. AUTO will show in the
display. Set the oven(s) to the cooking
temperature you need (don’t forget to set a
function if using the Multi-function oven). Turn
the Timer knob to the (AUTO) setting.
The ovens are now locked. After a few seconds
the display will revert to show the time of day
and the key symbol.
When your cooking is finished the beeper
sounds. Turn the Timer knob to the vertical ( )
to return to manual cooking.
If you are out, don’t worry about the beeper
going off, it stops after a while. When you return,
To turn off the key lock
Turn the Timer knob to the vertical ( ) to return
to manual cooking. Turn the thermostat to the
off position.
AUTO is showing, you want to
reset to manual cooking.
You can cancel any automatic settings by
briefly turning the Timer knob to the clock
Turn and hold the Timer knob to the clock
symbol
and then releasing it.
symbol ( ) for about 8 seconds. ‘Of’ will appear
on the display.
Clock Special Features
Key Lock
When the key lock is activated, the clock can be
operated as usual but the ovens are locked and
will not come on. This means that your child
could select a cook program but the program
will not be activated and ovens will not switch
on.
Keep holding the Timer knob turned to the clock
symbol ( ) and turn the Adjusting knob
clockwise until the key symbol ( ) goes out on
the display. Let go of the knobs.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
After a few seconds the display will revert to
show the time of day.
Whole poultry must be thoroughly defrosted
before placing in the oven.
Check that meat and poultry are fully
cooked before serving.
Both Ovens
Before using for the first time, heat the ovens to
200°C for 30 minutes to dispel manufacturing
odours.
The ovens can now be used normally.
Cooking using the timer
The wire shelves should always be pushed
firmly to the back of the oven.
The timer can be used to turn just one oven or
both on and off automatically. The start and stop
time must be the same for both ovens but
different cooking temperatures can be set.
Baking trays meat tins etcetera should be
placed level centrally on the oven’s wire
shelves. Keep all trays and containers away
from the sides of the oven, as overbrowning of
the food may occur.
If you want to turn one of the ovens on at
the same time as the timer is set for
automatic cooking, you must wait until the
timer has turned on the oven/ ovens first.
Then you can adjust either of them
manually in the normal way.
For even browning, the maximum
recommended size of a baking tray is 325mm
by 290mm.
Cooking high moisture
content foods can create a
‘steam burst’, when the oven
door is opened. When
opening the oven stand well
back and allow any steam to
disperse.
You can set the oven to turn on any time over
the following 24 hour period.
If you want to cook more than one dish,
choose dishes that require approximately
the same time. However, dishes can be
‘slowed down’ slightly by using small
containers and covering them with
aluminium foil, or ‘speeded up’ slightly by
cooking smaller quantities or placing in
larger containers.
When the oven is on, don’t
leave the door open for longer
than necessary, otherwise the knobs may get
very hot.
Very perishable foods such as pork or fish
should be avoided if a long delay period is
planned, especially in hot weather.
• Always leave a ‘fingers width’ between dishes
on the same shelf. This allows the heat to
circulate freely around them.
• The Cook & Clean oven liners (see Cleaning
your cooker) work better when fat splashes
are avoided. Cover meat when cooking.
Don’t place warm food in the oven.
Don’t use an oven already warm.
Don’t use if an adjoining oven is warm.
Avoid using wine or beer if there is a delay
period, as fermentation may take place.
To avoid curdling, cream should be added
to dishes just before serving.
• To reduce fat splashing when you add
vegetables to hot fat around a roast, dry them
thoroughly or brush lightly with cooking oil.
• Sufficient heat rises out of the oven while
cooking to warm plates in the grill
Fresh vegetables, which may discolour during a
delay period, should be coated in melted fat or
immersed in a water and lemon juice solution.
Fruit pies, custard tarts or similar wet mixtures
on top of uncooked pastry are only satisfactory if
there is a short delay period. Dishes containing
leftover cooked meat or poultry should not be
cooked automatically if there is a delay period.
compartment.
• If you want to brown the base of a pastry dish,
preheat the baking tray for 15 minutes before
placing the dish in the centre of the tray.
• Where dishes may boil and spill over during
cooking, place them on a baking tray.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-function oven
Fan oven
The left hand oven of your Elan cooker is Multi-
function. It has many varied uses. We suggest
you keep a careful eye on your cooking until you
are familiar with each function. Remember - not
all functions will be suitable for all food types.
This function operates the fan and the heating
element around it. An even heat is produced
throughout the oven, allowing you to cook large
amounts quickly.
Fan oven cooking is particularly suitable for
baking on several shelves at one time and is a
good ‘all-round’ function. It may be necessary to
reduce the temperature by approximately 10°C
for recipes previously cooked in a conventional
oven.
If you wish to pre-heat the oven, wait until the
indicator light has gone out before inserting the
food.
Fanned grilling
This function operates the fan whilst the top
element is on. It produces a more even, less
fierce heat than a conventional grill. For best
results, place the food to be grilled, on a grid
over a roasting tin, which should be smaller than
a conventional grill pan. This allows greater air
circulation. Thick pieces of meat or fish are ideal
for grilling in this way, as the circulated air
reduces the fierceness of the heat from the grill.
The oven door should be kept closed whilst
grilling is in progress, so saving energy. You will
also find that the food needs to be watched and
turned less than for normal grilling. Pre-heat this
function before cooking.
Please remember that all cookers vary -
temperatures in your new Elan ovens may differ
to those in your previous cooker.
Multi-function oven functions
Defrost
This function operates the fan to circulate cold
air only. No heat is applied. This enables small
items such as desserts, cream cakes and
pieces of meat, fish and poultry to be defrosted.
Defrosting in this way speeds up the process
and protects the food from flies. Pieces of meat,
fish and poultry should be placed on a rack,
over a tray to catch any drips. Be sure to wash
the rack and tray after defrosting.
Fan assisted oven
This function operates the fan, circulating air
heated by the elements at the top and the base
of the oven. The combination of fan and
conventional cooking (top and base heat)
makes this function ideal for cooking large items
that need thorough cooking, such as a large
meat roast. It is also possible to bake on two
shelves at one time, although they will need to
be swapped over during the cooking time, as
the heat at the top of the oven is greater than at
the base, when using this function.
Defrost with the oven door closed.
Large items, such as whole chickens and joints
should not be defrosted in this way. We
recommend this be carried out in a refrigerator.
Defrosting should not be carried out in a warm
oven or when an adjoining oven is in use or still
warm.
Ensure that dairy foods, meat and poultry are
completely defrosted before cooking.
This is a fast intensive form of cooking; keep an
eye on the food cooking until you have become
accustomed to this function.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Handyrack
Conventional oven (top and
base heat)
This function combines the heat from the top
and base elements. It is particularly suitable for
roasting and baking pastry, cakes and biscuits.
Food cooked on the top shelf will brown and
crisp faster than on the lower shelf, because the
heat is greater at the top of the oven than at the
base, as in ‘Fan assisted oven’ function. Similar
items being cooked will need to be swapped
around for even cooking. This means that foods
requiring different temperatures can be cooked
together, using the cooler zone in the lower half
of the oven and hotter area to the top.
The maximum weight than can be held by the
Handyrack is 5.5kg (12lb). It should only be
used with the supplied meat tin, which is
designed to fit the Handyrack. Any other vessel
could be unstable.
The Handyrack fits on the oven door. Food
cooking on it is easy to attend to, because it’s
accessible when the door is open. It can be
fitted at two different heights. One of the oven
shelves must be removed and the other
positioned to suit.
Browning element
This function uses the element in the top of the
oven only. It is a useful function for the browning
or finishing of pasta dishes, vegetables in
sauce, shepherds pie and lasagne, the item to
be browned being already hot before switching
to the top element.
When the Handyrack is used in its highest
position, other dishes can be cooked on the
bottom shelf position of the oven or standing on
the base of the oven
Base heat
When the Handyrack is used in its lowest
position, other dishes can be cooked on the
second shelf position of the oven or standing on
the base of the oven.
This function uses the base element only. It will
crisp up your pizza or quiche base or finish off
cooking the base of a pastry case on a lower
shelf. It is also a gentle heat, good for slow
cooking of casseroles in the middle of the oven
or for plate warming.
To fit the Handyrack, locate one side of it on the
door bracket.
The Browning and Base heat functions are
useful additions to your oven, giving you
flexibility to finish off items to perfection. With
use, you will soon realise how these functions
can combine to extend your cooking skills.
Then spring the other side out to clip it onto the
other bracket.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Steam
Oven shelves
During cooking, food naturally produces steam,
particulary when cooking foods with high water content
(e.g. oven chips). There may be some steam visible at
the grille at the rear of the hotplate. This is perfectly
normal.
the shelf guard should be at the back pointing upwards
As this steam can condense to water droplets on the cool
outer trim of the oven, it may be necessary during
cooking to wipe away any moisture with a soft cloth. This
will also help to prevent soiling and discolouration of the
oven exterior by cooking vapours.
The oven shelves can be easily removed and
refitted.
Pull the shelf forward until the back of the shelf
is stopped by the shelf stop bumps in the oven
sides.
Oven light
Press the appropriate button to turn on one of
the oven lights.
Lift up the front of the shelf so the back of the
shelf will pass under the shelf stop and then pull
the shelf forward.
If one of the oven lights fail, turn off the power
supply before you change the bulb. See the
‘Troubleshooting’ section for details on how to
change an oven light bulb.
To refit the shelf, line up the shelf with a groove
in the oven side and push the shelf back until
the ends hit the shelf stop. Lift up the front so
the shelf ends clear the shelf stops, and then
lower the front so that the shelf is level and push
it fully back.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
The bottom drawer is for storing oven trays and
other cooking utensils.
It can get very warm, don’t store anything in it
which may melt or catch fire.
The drawer can be removed completely for
cleaning etc.
Lift up the ends of the plastic clips (one each
side) to release the catches holding the drawer
to the side runners and at the same time pull the
drawer forward and away from the side runners.
For safety’s sake push the drawer runners back
out of the way.
To remove the drawer pull it fully forward
To refit the draw
Pull out the side runners. Rest the drawer back
on the side runners and, keeping it level, push it
right back. The clips should click into position
holding the drawer to the side runners.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-function Oven cooking guide
Remember - not all functions will be suitable for all food types. The oven control settings and
cooking times given are intended to be used only as a guide. Individual tastes may require the
temperature to be altered to provide a preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the temperature by 10°C and the cooking time by 5-10 minutes. The
temperature in the fanned oven does not vary with height in the oven - so you can use any
shelf.
The shelves should not be fitted directly one above the other. When cooking on more than one
shelf always leave at least one runner space between them. Place baking trays, individual
cake tins or baking dishes centrally on the oven shelf. For best results pre-heat the oven until
the oven indicator light goes out.
Cooking chart - Fan assisted oven function
Oven Shelf
Food
Temp
170°C
180°C
160°C
190°C
Position Approximate Cooking Time
Fairy cake
Scone
2-4
2-4
2-4
2-4
20 min
15 min
Deep apple pie
Plate tart
45 min interchange after 25 minutes
45 min interchange After 25 minutes
Rich fruit cake
197mm x 92mm
Victoria sandwich
180mm
145°C
3
1 hr 45 min - 2 hr
170°C
150°C
220°C
2-4
3
20 - 25 min
Milk pudding
Puff pastry
2 hrs
3 - 5
15-40 mins according to size. Interchange 2/3rds through cooking time
For roast meats and poultry refer to the Fan oven guide - reduce cooking time slightly.
500g is approximately 1lb (1lb 2oz)
Ensure meat and poultry is fully cooked before serving
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven Cooking chart - Conventional and full Fan oven functions
Convection Oven
Shelf
Fan Oven
Temp
Food
Temp
Position
Approximate Cooking Time
Fillets 15-20mins.
FISH
190°C
3
180°C
190°C
190°C
3
3
180°C
180°C
Whole 10mins.per 500g + 10mins.
Steaks according to thickness.
ROAST MEATS
Beef with bone
160°C
200°C
160°C
200°C
160°C
200°C
160°C
200°C
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
150°C
190°C
150°C
190°C
170°C
190°C
150°C
190°C
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
30-35mins. per 500g + 30-35mins.
20-25mins. per 500g + 20-25mins.
30-35mins. per 500g + 30-35mins.
25-35mins. per 500g + 25-30mins.
35-40mins. per 500g + 35-40mins.
25-30mins. per 500g + 25-30mins.
Beef without bone
Lamb
Pork
Stuffed and rolled - Add approx. 10 mins. per 500g to above cooking times or cook at 200°C for 20mins. then 160°C
for remainder.
THOROUGHLY THAW FROZEN JOINTS AND POULTRY BEFORE COOKING.
POULTRY
Chicken
Turkey
160°C
200°C
160°C
200°C
2-3
2-3
1-3
1-3
150°C
190°C
150°C
190°C
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
Stuffed Poultry - Cook at 200°C or at 200°C for 20mins. then 160°C for remainder. Prepacked (fresh or frozen)
follow packers cooking times
CASSEROLE
140-150°C
220°C
2-3
4
140°C
200°C
2-4hrs according to recipe.
YORKSHIRE PUDDING
Large tin 30-35mins. Individual 10-20mins.
CAKES
Very Rich Fruit
Rich fruit (180mm)
Madeira (180mm)
Queen Cakes
Scones
140°C
150°C
160°C
2
2
2
140°C
145°C
150°C
180°C
210°C
170°C
45-50mins. per 500g mixture
21/2-3hrs.
80-90mins.
190°C 3 & 5 or 3
220°C 2 & 4 or 3
180°C 2 & 4 or 3
15-25mins.
10-15mins.
Victoria Sandwich
20-30mins.
PASTRIES
Plate Tart
Fruit Pie
200°C
200°C
200°C
220°C
220°C
110°C
2 & 4
2 & 4
4
190°C
190°C
190°C
200°C
200°C
100°C
45-50mins. Interchange after 25mins.
35-40mins.
Tartlets
15-20mins. according to size.
20-40mins. according to size.
20-30mins.
Puff Pastry
BREAD
2,3 or 4
2 & 4
3
MERINGUES
2-21/2hrs
PUDDINGS
Baked Egg Custard
Baked sponge pudding
Milk pudding
160°C
190°C
3
3
3
150°C
180°C
150°C
45mins.-1hr.
40-45mins.
2-3hrs.
140-150°C
17
Download from Www.Somanuals.com. All Manuals Search And Download.
The Wok burners
Cleaning your cooker
The Wok burners are a little more complicated
but it also can be taken apart for cleaning.
Essential information
Before thorough cleaning isolate the electricity
supply. Remember to switch on the electricity
supply before use.
Never use paint solvents, washing soda,
caustic cleaners, biological powders,
bleach, chlorine based bleach cleaners,
coarse abrasives or salt. Don’t mix
different cleaning products - they may
react together with hazardous results.
Recommended cleaning materials are
shown in the chart below.
If you want to move your cooker for cleaning,
see the section called ‘Moving your cooker’.
All parts of the cooker can be cleaned with hot
soapy water - but take care that no surplus
water seeps into the appliance.
For cleaning materials see the ‘Cleaning Table’
at the end of this section.
Wok burner
A
C
E
inner burner cap,
inner burner head
Wok burner base
When reassembling a Wok burner, turn over the
large base ring and find the ‘D’ shaped area.
B
D
outer burner cap
outer burner head
Hotplate burners
Some models have a separate trim ring, which
fits on the burner head.
The burner heads and caps can be removed for
cleaning. Make sure they are absolutely dry
before replacing.
The central hotplate
A cap, B head, C notch, D electrode, E base
When refitting the burner head, make sure that
the notch lines up with the electrode or hole in
the base. Check that the burner head is level
and that the cap is fitted centrally on the burner
head.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the head until the ‘D’ matches the one on
the burner base. Turn the head over and place it
on the burner base. To fit the small inner burner,
find the larger electrode notch in the burner rim.
Line this up with the white ignition electrode and
place the inner burner on the large base ring.
Ovens
The ovens have removable panels that have
been coated with a special enamel that partly
cleans itself. This does not stop all marks on the
lining, but helps to reduce the amount of manual
cleaning needed.
The Cook & Clean panels work better
above 200°C. If you do most of your
cooking below this temperature,
occasionally remove the panels and wipe
with a lint free cloth and hot soapy water.
The panels should then be dried and
replaced and the oven heated at 200°C for
about one hour. This will ensure the Cook &
Clean panels are working effectively.
Don’t use steel wool (Brillo) or any other
materials which will scratch the surface. Don’t
use oven cleaning pads.
A
electrode notch
Now fit the two trim rings, making sure that they
are sitting down properly.
B
ignition electrode
Removing the Oven Linings
Some of the lining panels can be removed for
cleaning and for cleaning behind. Remove the
shelves first.
Griddle
Always clean the griddle after use. Allow to cool
The right hand fanned oven has a removable
oven roof - slide the roof liner forward and
remove.
completely before removing. Immerse the
griddle plate in hot soapy water. Use a soft cloth
or, for stubborn stains, a nylon washing up
brush.
NEVER USE CAUSTIC OR ABRASIVE
CLEANERS AS THESE WILL DAMAGE THE
SURFACE.
Grill
The grill pan and grid should be washed in hot
soapy water. After grilling meats or any foods
that soil, leave to soak for a few minutes in the
sink immediately after use. Stubborn particles
may be removed from the grid by using a nylon
brush.
The side panels of either oven can be removed.
Each side of the oven is fixed with four fixing
screws. You don’t have to remove the screws to
remove the oven linings. Lift each side panel
upwards and they will slide off the screws. Then
pull them forwards.
Control Panel and Doors
Avoid using any abrasive cleaners including
cream cleaners, e.g. Cif, on brushed Stainless
Steel surfaces. For best results use a liquid
detergent e.g. Domestos Multi Surface Cleaner.
The control panel and control knobs should only
be cleaned with a soft cloth wrung out in clean
hot soapy water. Wipe with a clean dampened
cloth then polish with a dry cloth. The oven
doors should only be cleaned with a soft cloth
wrung out in clean hot soapy water.
Once the linings are removed, the oven enamel
interior can be cleaned.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning Table
Hotplate
Part
Finish
Recommended Cleaning Method
Hotplate Top
Enamel or
Hot soapy water, soft cloth. Any stubborn stains remove
gently with a nylon scourer.
Stainless Steel
Pan Supports, Wok Cradle (some
models only)
Enamel coated
Cast Iron or
Cif Cream Cleaner- Faberge Lever and a nylon scourer.
Dishwasher.
Stainless Steel
Warming Zone (some models only) Toughened Glass Hot soapy water, cream cleaner/scourer if necessary.
Burner Caps
Enamel
Cream cleaner, nylon scourer. Dishwasher
Burner Trim Rings (some models
only) and Burner Head
Aluminium
Cif or other cream cleaner with a soft cloth. Be careful not to
be over vigorous.
Griddle Plate (some models only)
Non-Stick Surface Allow to cool. Wash in hot soapy water. Do not use abrasive
cleaners/scourers. Dishwasher.
Outside of cooker
Part
Finish
Recommended Cleaning Method
Door, Door surround and Storage
Drawer exterior.
Enamel or paint
Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.
Stainless Steel
E Cloth (Comet) or Vileda Microfibre Plus All Purpose Cloth
Freudenberg Household Products LP (supermarket)
Sides and Plinth
Painted surface
Hot soapy water, soft cloth
Splashback/Rear Grille
Enamel or
Hot soapy water, soft cloth. Cream cleaner, with care, if
necessary.
Stainless Steel
Control panel
Paint, Enamel or
Stainless Steel
Warm soapy water. Do not use abrasive cleaners on
lettering.
Control Knobs/Handles
Oven Door Glass/Glass Lid
Oven and Grill
Plastic/ Chrome
Warm soapy water, soft cloth.
Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
Part
Finish
Recommended Cleaning Method
Sides, floor & roof of oven -
NOT COOK & CLEAN OVEN
PANELS (see below)
Enamel
Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS -
FOLLOW MANUFACTURERS INSTRUCTIONS. Do not
allow contact with the oven elements. Protect the burner in
gas ovens with foil whilst cleaning the oven interior.
Cook & Clean Oven Panels (some Special enamel
This surface cleans itself at 200°C and above, or the panels
models only)
that partly cleans can be removed and washed with hot soapy water and a
itself
nylon brush. (see ‘The Ovens’ in ‘Cleaning your cooker’)
Oven Shelves, Handyrack, Grill
Trivet, Handygrill rack
Chrome
An oven interior cleaner that is suitable for chrome. Soap
filled pad. Dishwasher.
Grill Pan/Meat Tin, Handygrill Pan
(some models only)
Enamel
Hot soapy water. Soap filled pad (Brillo). Dishwasher.
Cleaners listed are available from Supermarkets or electrical retailers as stated. Cleaner manufacturer
in Italics
For enameled surfaces use a cleaner that is approved for use on vitreous enamel. The vitreous enamel
01527 893031.
Regular cleaning is recommended. For easier cleaning, wipe up any spillages immediately.
To help keep your oven clean, cover meat when roasting, with foil or use a roasting bag. Brush
vegetables with fat before placing around the meat.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
When replacing the linings fit the side linings
first.
Turn the levelling tool clockwise, two full
(180°) turns. It will be stiff. The front of the
oven will rise slightly as the roller drops
down.
Make sure you fit the oven roof with the slot at
the front.
Moving your cooker
Switch off the electricity supply.
The cooker is heavy; two people may be
required to move it. The cooker is fitted with
one roller at the front and two at the back.
There are also two screw down levelling
feet at the front.
The front roller, designed for moving the cooker
can be wound down. The levelling tool that
controls this roller is in the storage drawer.
Open the grill door and right hand oven door so
that you can get a good grip on the bottom of
the fascia panel as you move the oven.
To remove the drawer, pull it right out
Do not move the oven by pulling the hand
rail, door handles or knobs.
Move the oven a bit at a time, checking behind it
to make sure the gas hose is not caught. Make
sure both electricity and gas cables have
sufficient slack to move the cooker forward as
you go along.
Lift up the ends of the plastic clips (one each
side) to release the catches holding the drawer
to the side runners and at the same time pull the
drawer forward and away from the side runners.
For safety’s sake push the drawer runners back
out of the way.
If a stability chain is fitted, release it as you
ease the cooker out.
When you replace the cooker, wind it down off
the rollers by turning the levelling tool anti-
clockwise. This is important. It will stop the
cooker moving accidentally, while in use.
Locate levelling tool as shown. If you cannot find
the levelling tool, contact your installer. See the
start of the ‘Installation’ section of these
instructions.
To refit the draw
Pull out the side runners. Rest the drawer back
on the side runners and, keeping it level, push it
right back. The clips should click into position
holding the drawer to the side runners.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
cause nuisance tripping. In these instances the
cooker circuit may need to be protected by
fitting 100mA device. This work should be
carried out by a qualified electrician.
Troubleshooting
Steam is coming from the oven
During cooking, food naturally produces steam,
particulary when cooking foods with high water
content (e.g. oven chips). There may be some
steam visible at the grille at the rear of the
hotplate. This is perfectly normal. Steam can
condense to water droplets on the cool outer
trim or the oven door. It may be necessary
during cooking to wipe away any moisture with a
soft cloth. This will also help to prevent soiling
and discolouration of the oven exterior by
cooking vapours.
Food is cooking too slowly, too quickly, or
burning
Cooking times may differ from your previous
oven. Check that you are using the
recommended temperatures and shelf positions.
See pages 16 -17. The oven control settings
and cooking times are intended to be used only
as a guide. Individual tastes may require the
temperature to be altered either way, to get the
results you want. Try cooking at a higher
temperature setting. Is the oven roof in?
Take care when opening the oven door as there
may be a momentary puff of steam when the
oven door is opened. Stand well back and allow
any steam to disperse.
The oven is not cooking evenly
Do not use a tin or tray larger than 320mm x
305mm.
If you are cooking a large item, be prepared to
turn it round during cooking.
If two shelves are used, check that space has
been left for the heat to circulate. When a
baking tray is put into the oven, make sure it is
placed centrally on the shelf.
The oven fan is noisy
The note of the oven fan may change as the
oven heats up - this is perfectly normal.
What cleaning materials are recommended for
the cooker?
See the ‘Cleaning’ section of the Easy Guide for
a full list of recommended cleaning materials.
We do not recommend Mr. Muscle, as it
contains chemicals which may damage the
surfaces of your cooker.
Check that the door seal is not damaged and
that the door catch is adjusted so that the door
is held firmly against the seal.
A dish of water when placed on the shelf should
be the same depth all over. (For example, if it is
deeper at the back, then the back of the cooker
should be raised up or the front lowered). If the
cooker is not level arrange for your supplier to
level it for you.
The knobs get hot when I use the oven or
the grill, can I avoid this?
Yes, this is caused by heat rising from the oven
or the grill, and heating them up. Don’t leave the
oven door open. Make sure that the grill pan is
pushed right back to the ‘backstop’ when
grilling.
Oven not coming on when turned on
manually
Is the power on? Is the clock illuminated?
If using the Multi-function oven have you set a
cooking function?
If there is an installation problem and I don’t
get my original installer to come back to fix
it who pays?
If not there may be something wrong with the
power supply. Is the cooker supply on at the
isolator switch?
You do. Service organisations will charge for
their call outs if they are correcting work carried
out by your original installer. It’s in your interest
to track down your original installer.
If this does not solve the problem contact a
service person.
Current Operated Earth Leakage Breakers
Where the cooker installation is protected by a
30 milliamp sensitivity residual current device
(RCD), the combined use of your cooker and
other domestic appliances may occasionally
Oven not coming on when automatic cooking
Timer set correctly but oven knob left OFF by
mistake?
If using the Multi-function oven have you set a
cooking function?
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven temperature getting hotter as the
cooker gets older
If turning the knob down has not worked or only
worked for a short time then you may need a
new thermostat. This should be fitted by a
service person.
Grill not cooking properly
Are you using the pan and trivet supplied with
the cooker? Is the pan being used on the
runners, not the floor of the compartment? Is the
grill tray pushed fully back to stop?
The oven light is not working
The bulb has probably blown. You can buy a
replacement bulb (which is not covered under
the guarantee) from a good electrical shop. Ask
for an Edison screw fitting 15w 240v lamp, FOR
OVENS. It must be a special bulb, heat resistant
to 300 °C. See the HELP leaflet for spares by
mail order.
Open the oven door and remove the Handyrack
(if fitted) and oven shelves.
Turn off the power supply.
Unscrew the bulb cover by turning
anticlockwise. Unscrew the old bulb. Screw in
the new bulb, screw back the bulb cover. Turn
on the electricity supply and check that the bulb
now lights.
Unscrew the old bulb and fit the new one.
Hotplate ignition or hotplate burners faulty
Is the power on? Is the clock illuminated? If not
there maybe something wrong with the power
supply.
See ‘power supply’ section further on.
Are the sparker (ignition electrode) or burner
slots blocked by debris?
Is the burner trim correctly located?
Are the burner caps correctly located?
See the section entitled ‘Cleaning’
Hotplate burners will not light
If only one or all the hotplate burners will not
light, make sure that the parts have been
replaced correctly after wiping or removing for
cleaning.
Check that there is not a problem with your gas
supply. You can do this by making sure that
other gas appliances you may have are working.
Do the burners spark when you push the
button? If not check the power is on - is the
clock illuminated?
23
Download from Www.Somanuals.com. All Manuals Search And Download.
All parts of the cooker become hot with use
and will retain heat even after you have
stopped cooking.
General Safety Instructions
The cooker must be installed by a CORGI
registered engineer in accordance with the
installation instructions. The installation must
comply with the relevant regulations and also
the local gas and electricity supply companies’
requirements.
Take care when touching cooker, to minimize
the possibility of burns, always be certain that
the controls are in the OFF position and that it is
cool before attempting to clean the cooker.
Use dry oven gloves when applicable -
using damp gloves might result in steam
burns when you touch a hot surface. Never
operate the cooker with wet hands.
If you smell gas
Don’t turn electric switches on or off.
Don’t smoke
Don’t use naked flames
Do turn off the gas at the meter or cylinder
Do open doors and windows to get rid of the
gas
Call your gas supplier.
Do not use a towel or other bulky cloth in place
of a glove. They might catch fire if they touch a
hot surface.
Clean with caution. If a wet sponge or cloth
is used to wipe spills on a hot surface, be
careful to avoid steam burns. Some
cleansers can produce noxious fumes if
applied to a hot surface.
If you are using natural gas in the UK ring British
Gas - Trans Co on
Do not use unstable saucepans and position the
handles away from the edge of the hotplate.
0800 111 999
Babies, toddlers and young children should
not be allowed near the cooker at any time.
They should never be allowed to sit or stand
on any part of the appliance. Teach them
not to play with controls or any other part of
the cooker.
This appliance is designed for domestic
cooking only. Use for any other purpose
could invalidate any warranty or liability
claim.
The use of a gas cooking appliance results in
the production of heat and moisture in the room
in which it is installed. Ensure that the kitchen is
well ventilated: keep natural ventilation holes
open or install a mechanical ventilation device,
(mechanical extractor hood).
Never store anything of interest to children in
cabinets above a cooker - children climbing on
the cooker to reach them could be seriously
injured.
Clean only parts listed in this guide.
In the interests of hygiene and safety the cooker
should be kept clean at all times as a build up in
fats and other food stuff could result in a fire.
Prolonged intensive use of the appliance may
call for additional ventilation, for example
opening a window, or more effective ventilation,
for example increasing the level of mechanical
ventilation where present.
Always keep combustible wall coverings or
curtains etc. a safe distance away from your
cooker.
The cooker should be serviced by a qualified
service engineer and only approved spare parts
used. Have the installer show you the location of
the cooker control switch. Mark it for easy
reference. Always allow the cooker to cool and
then switch off at the mains and before cleaning
or carrying out any maintenance work, unless
specified otherwise in this guide.
Do not spray aerosols in the vicinity of the
cooker while it is in on.
Do not store or use combustible materials,
or flammable liquids in the vicinity of this
appliance.
Do not use water on grease fires. Never pick up
a flaming pan. Turn the controls off. Smother a
flaming pan on a surface unit by covering the
pan completely with a well fitting lid or baking
tray. If available use a multipurpose dry
chemical or foam-type fire extinguisher.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Never leave the hotplate unattended at high
heat settings. Pans boiling over can cause
smoking and greasy spills may catch on
fire.
Make sure that your kitchen is well
ventilated at all times. Use extractor fans or
hoods when fitted.
Never heat unopened food containers. Pressure
build up may make container burst and cause
injury.
Never wear loose-fitting or hanging clothes
while using the appliance. Be careful when
reaching for items stored in cabinets over the
hotplate. Flammable material could be ignited if
brought in contact with a hot surface unit and
may cause severe burns.
The cooker is designed for cooking foods
only and must not be used for any other
purpose.
The oven should NOT be used for heating the
kitchen, not only does this waste fuel but the
control knobs may become overheated.
Take great care when heating fats and oils,
as they will ignite if they get too hot.
Use a deep fat thermometer whenever possible
to prevent overheating fat beyond the smoking
point.
When the oven is on DO NOT leave the
oven door open for longer than necessary.
The specification of this cooker should not be
altered.
Never leave a chip pan unattended. Always
heat fat slowly, and watch as it heats. Deep
fry pans should be only one third full of fat.
Filling the pan too full of fat can cause spill
over when food is added. If you use a
This appliance is heavy, take care when
moving it.
When the cooker is not in use ensure that the
control knobs are in the off position.
combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
Foods for frying should be as dry as possible.
Frost on frozen foods or moisture on fresh foods
can cause hot fat to bubble up and over the
sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or
medium high temperatures. Never try to move a
pan of hot fat, especially a deep fat fryer. Wait
until the fat is cool.
When the grill is on, do not use the top of
the flue (the slot along the back of the
cooker) for warming plates, dishes, drying
tea towels or softening butter.
When using an electrical appliance near the
hotplate, be sure that the cord of the appliance
does not come into contact with the hotplate.
Take care that no water seeps into the
appliance
Only certain types of glass, glass-ceramic,
earthenware or other glazed containers are
suitable for hotplate cooking; others may
break because of the sudden change in
temperature.
Do not allow anyone to climb, stand or hang
on any part of the cooker.
Do not use aluminium foil to cover shelves,
linings or the oven roof.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
For LP Gas - BS 5482-1:1994 (when the
installation is in a permanent dwelling), BS
5482-2:1977, (when the installation is in a
caravan or other non permanent dwelling), or
BS 5482-3:1999 , (when the installation is in a
boat).
Installation
Dear Installer
Before you start your installation, please
complete the details BELOW.
The Gas Safety (Installation and Use)
regulations 1998.
The relevant Building / IEE regulations.
If your customer has a problem relating to your
installation they will be able to contact you
easily.
Provision of Ventilation
Thank you
This appliance is not connected to a combustion products
evacuation device. Particular attention shall be given to
the relevant requirements regarding ventilation.
Installer’s Name
The room containing the cooker should have an air
supply in accordance with BS 5440 Part 2 : 2000. All
rooms require an openable window or equivalent, while
some rooms require a permanent vent in addition to the
openable window. The cooker should not be installed in a
bedsitting room with volume less than 20m3. If it is
installed in a room of volume less than 5m3 an air vent of
effective area 100cm2 is required; if it is installed in a
room of volume between 5m3 and 10m3, an air vent of
effective area 50cm2 is required; while if the volume
exceeds 11m3, no air vent is required.
Installer’s Company
Installer’s Telephone number
You must be aware of the
following safety requirements &
regulations
Prior to installation, ensure that the local distribution
conditions (nature of the gas and gas pressure) and the
adjustment of the appliance are compatible.
If there are other fuel burning appliances in the same
room, BS 5440 Part 2 : 2000 should be consulted to
determine the requisite air vent requirements.
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner but
This appliance shall be installed in accordance with the
regulations in force and only in a well ventilated space.
Read the instructions before installing or using this
appliance.
NOT in a room containing a bath or shower.
NOTE:
An appliance for use on LPG shall not be installed in
a room or internal space below ground level. e.g. in a
basement.
In the UK the regulations and standards are as follows:-
In your own interest and that of safety, it is law that all
gas appliances be installed by competent persons.
CORGI registered installers undertake to work to safe
and satisfactory standards. Failure to install the appliance
correctly could invalidate any warranty or liability claims
and lead to prosecution. The cooker must be installed in
accordance with
All relevant British Standards / Codes of
Practice, in particular BS 5440 Part 2 2000,
For Natural Gas - BS 6172 : 1990 and BS
6891 : 1998
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Must be in accordance with
the relevant standards.
Conversion
Checking the parts
4 pan supports
All models are supplied set for use
on group H natural gas. A conversion
kit for LP gas is included with the
appliance. See the instructions that
are supplied with the conversion kit.
After converting the appliance please
attach the Gas Conversion sticker
over the appropriate area of the data
badge, this will identify the gas type
the appliance is now set for.
MULTIMETER
(for electrical checks)
Griddle plate
You will also need the
following tools:
1. Electric drill
This appliance is designed
for domestic cooking only.
Use for any other purpose
could invalidate any
Grill pan and trivet
2. Masonry drill bit
(only required if fitting the cooker
on a stone or concrete floor)
warranty or liability claim.
3. Rawlplugs
You will need the
following equipment to
complete the cooker
installation
satisfactorily
STABILITY BRACKET
(only required if fitting the cooker
on a stone or concrete floor)
Levelling tool
Handyrack
4. Steel tape measure
5. Cross head screwdriver
6. Flat head screwdriver
7. 4mm & 3mm Allen keys
8. Spirit level
9. Pencil
10. Adjustable spanner
If the cooker is to be supplied
with gas through a flexible
hose, a stability bracket or
chain must be fitted.
11. Screws for fitting
stability bracket
Meat tin
These are not supplied by
with the cooker but are
available at most builders’
merchants.
4 Main oven shelves
Splashback & Plinth
GAS PRESSURE TESTER
FLEXIBLE GAS HOSE
Conversion kit from Natural gas to
LP gas
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning the Cooker
The diagrams below show the minimum recommended
distance from the cooker to nearby surfaces.
The cooker should not be placed on a base.
Unpacking the Cooker
Do not take any packaging off the cooker until it is
directly in front of the place it is to be installed (unless
it will not fit through a door in its outer packaging).
Cut the banding straps and lift the cardboard box off
the cooker, LEAVING THE COOKER STANDING ON
THE BASE PACKAGING. See the loose unpacking
sheet.
The hotplate surround should be level with, or above,
any adjacent work surface. Above hotplate level a gap
of 75mm should be left between each side of the
cooker and any adjacent vertical surface.
Moving the Cooker
The cooker is very heavy. Take great care.
We recommend two people manoeuvre the cooker.
Ensure that the floor covering is firmly fixed, or
removed to prevent it being disturbed when moving the
cooker around. You will need the levelling tool.
For non-combustible surfaces (such as unpainted
metal or ceramic tiles) this can be reduced to 25mm.
A minimum space of 650mm is required between the
top of the hotplate and a horizontal combustible
surface.
From the back tilt the cooker forward and remove the
rear half of the polystyrene base pack.
Repeat from the front and remove the front half of the
poly base. Pull the drawer out to its furthest point.
*Any cooker hood should be installed in accordance
with the hood manufacturer’s instructions.
Surfaces of furniture and walls at the sides and rear of
the appliance should be heat, splash and steam
resistant. Certain types of vinyl or laminate kitchen
furniture are particularly prone to heat damage and
discolouration. We cannot accept responsibility for
damage caused by normal use of the cooker to any
material that de-laminates or discolours at
temperatures less than 65°C above room temperature.
For safety reasons curtains must not be fitted
immediately behind the cooker.
We recommend a gap of 1110mm between units to
allow for moving the cooker. If a flush fit is required, fit
the cooker up to the unit at one side then fit the unit the
other side. Do not box the cooker in; it must still be
possible to move the cooker in and out for cleaning
and servicing. The cooker should not be placed on a
base.
Lift up the ends of the plastic clips (one each side) to
release the catches holding the drawer to the side
runners and at the same time pull the drawer forward
and away from the side runners. For safety’s sake
push the drawer runners back out of the way.
A clearance of 130mm is required if the cooker is near
a corner of the kitchen to allow the oven doors to open.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Fit the levelling tool on the rectangular adjuster as
shown below.
Levelling
You are recommended to use a spirit level on a shelf in
one of the ovens to check for level.
Place the cooker in its intended position taking care not
to twist it within the gap between the kitchen units as
damage may occur to the cooker or the units.
The rollers can be adjusted to level the cooker. To
adjust the height of the rear of the cooker use the
levelling tool supplied to turn the adjusting nuts at the
front bottom corners of the cooker.
Adjust the height of the front roller to level the cooker.
Turn clockwise to raise the cooker and anticlockwise to
lower.
LOWER THE FRONT ROLLER by doing 14 complete
(360°) turns clockwise. (This means turning and
removing the levelling tool 56 times).
When you are satisfied with the height and level raise
the front of the cooker by one turn of the front roller
adjuster. Screw down the front feet to meet the floor.
Screw the front roller adjuster anticlockwise to raise the
front roller so that the front of the cooker is supported
on the feet, not the front roller, to prevent accidental
movement of the cooker.
Now LOWER THE TWO REAR ROLLERS.
First fit the levelling tool on the hexagonal adjusting nut
as shown below.
Leave the levelling tool in the storage drawer, so
that the customer can use it if they wish to move
the cooker.
To refit the draw pull out the side runners. Rest the
drawer back on the side runners and, keeping it level,
push it right back. The clips should click into position
holding the drawer to the side runners. Replace the
drawer by locating on side runners and push in.
Make 10 complete (360°) turns clockwise. (This means
turning and removing the levelling tool 20 times).
Fit the Handles
Remove the 4mm Allen screws from the doors with the
hexagon key tool. Use the screws to fit the door
handles.
Make sure you lower BOTH REAR ROLLERS. There are
two adjusting nuts, one for each roller, at both the front
bottom corners of the cooker.
The handles should be above the fixings.
Unfold the rear edge of pack base tray. Carefully push
the cooker backwards along the hardboard strips and
into position. Take care not to damage the power cable.
Push the cooker close to its final position, leaving just
enough space to get behind it.
Fit the plastic blanking plugs to the fixing holes.
Remove the 4mm Allen screws from the top corners of
the fascia and fix the front handrail in position.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting the splash back
Gas Connection
It is essential the splash back is fitted. Remove the
two fixing screws (3mm hexagonal socket head) and
nuts that pass through the top of the rear flue grille.
Hold the splash back in position. From the rear refit the
2 fixing screws and nuts.
The Gas supply needs to terminate with a down facing
bayonet. The rear cover boxes limit the position of the
supply point.
Fitting a stability bracket
A stability bracket or chain (not supplied by with the
cooker) should be fitted when the cooker is connected
to a flexible gas supply.
When fitting a stability bracket read these instructions
together with the leaflet supplied with the bracket.
1. Place the cooker in its intended position and level
the cooker.
2. Draw a pencil line 100mm from the front edge of
the levelling feet.
3. Mark the centre line for the bracket by measuring
550mm from the left hand side of the cooker.
view from the rear
A
B
position for gas supply connector
appliance gas inlet
Because the height of the cooker can be adjusted and
each connection is different it is difficult to give precise
dimensions. Ideally the house supply bayonet should
be in the shaded area shown in the diagram. Although
a 900mm hose can be used, a 1250mm hose will
allow slightly more flexibility in the positioning of the
bayonet and make moving the cooker easier. The
hose should be fitted so that both inlet and outlet
connections are vertical so that the hose hangs
downwards.
4. Lower the front roller and move the cooker forward.
5. Measure back from the pencil line 550mm to locate
the front edge of the bracket. Fix the bracket to the
floor.
The connector is located just below the hotplate level
at the rear of the cooker.
6. Measure the height from floor level to engagement
edge in back of cooker. Add 3mm to this dimension
and assemble the stability bracket to this height.
(i.e. from floor level to underside of the top
member) and ensure the bracket does not foul the
oven burner assembly.
For Natural Gas the flexible hose must be in
accordance with B.S.669.
If in doubt contact, your supplier.
Screw connect the threaded end of the hose into the
gas inlet in the underside of the connector block on
the back of the cooker.
After completing the gas connection, check the
cooker is gas sound with a pressure test.
Pressure testing
The gas pressure can be measured at one of the
centre hotplate burner injectors (not the Wok burners).
Lift off a burner head. Fit the pressure gauge to the
injector. Turn on the hotplate burner and turn on and
light one of the other hotplate burners.
For Natural Gas cookers the pressure should be
20mbar.
For LP Gas cookers the pressure should be
29mbar for Butane
37mbar for Propane.
Reassemble burner top, making sure it is reassembled
in the correct way on the burner body.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Hotplate
This appliance must be installed by a qualified
electrician to comply with the relevant Institute of
Electrical Engineers (I.E.E.) regulations and also
the local electricity supply company requirements.
Check each burner in turn. Push in tap and turn to the
large flame symbol. Press ignition switch on facia
panel.
Grill
WARNING: THIS APPLIANCE MUST BE EARTHED
Open the grill compartment door. Turn on the grill
control and check that the grill heats up.
Note
The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker,
through a suitable cooker control unit incorporating a
double pole switch having a contact separation of at
least 3mm in all poles. This cooker must not be
connected to an ordinary domestic power point.
Oven check
Set the clock to the time of day
When the clock is first connected the display will flash
(
) and (
) alternately.
To set the clock to read the time of day turn and hold
the Timer knob to the clock symbol and at the same
time turn the Adjusting knob left or right until the clock
shows the time of day. Remember this is a 24 hour
clock. Let go of the Timer knob and it will spring back
to the vertical
oven manual setting.
Turn on the oven and check that the oven fan starts to
turn and that the oven starts to heat up. Turn off the
oven.
The cable size used should be between 6mm2 and
10mm2, twin and earth.
Fitting the plinth
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel.
Connect the mains cable to the correct terminals for
your electrical supply type (see fig.). Check that the
links are correctly fitted and that the terminal screws
are tight. Secure the mains cable using the cable
clamp.
Loosen the 3 screws along the front bottom edge of the
cooker. Hook the central keyhole over the central
screw. Twist and fit each end keyhole over their
respective screws. Tighten the fixing screws.
These appliances are of type X with regard to
protection against over heating of the surrounding
surfaces.
Current Operated Earth Leakage Breakers
Where the installation is protected by a 30 milliamp
sensitivity residual current device (RCD), the combined
use of your cooker and other domestic appliances may
occasionally cause nuisance tripping. In these
instances the cooker circuit may need to be protected
by fitting 100mA device. This work should be carried
out by a qualified electrician.
Oven Light
Press the oven light switch and check that the light is
working.
Customer care
Please complete your details in this Guide, inform the
user how to operate the cooker and hand over the
Instructions.
NB. The oven light bulb is not included in the
guarantee
Thank you.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Remove the 2 cross headed screws that were hidden
by the hand rail end brackets.
Conversion to LP gas
Check in the Technical Data
section at the back of the book
that the cooker is convertible to
Open the oven door & or grill door and remove the
the gas you want to use.
fixing screws underneath the control panel. NB some
models have a plate under the facia held in place by
This conversion must be performed by a
competent person. After conversion the
installation must comply with the relevant
regulations and also the local electricity supply
company requirements. Read the instructions
before converting this appliance.
the bottom fixing screws.
Lower facia panel clear of top retaining tags.
Failure to convert the appliance correctly could
invalidate any warranty or liability claims and
lead to prosecution.
This instruction must be used in conjunction with the
rest of the appliance instruction, in particular for
information on Standards, cooker positioning,
connection hose suitability etc.
When servicing or replacing gas-carrying components
disconnect from gas before commencing operation and
check appliance is gas sound after completion.
A tap bypass screw
Turn the bypass screw on each gas control clockwise
to the stop.
Do not use re-conditioned or unauthorised gas
controls.
Stick on label
Jets
Stick the appropriate label on to the data badge to
indicate the gas the appliance is now set for.
Standard burner
Wok burner
Pressure Testing
Connect the appliance to the gas supply. Check the
appliance is gas sound.
The gas pressure can be measured at one of the left
hand hotplate burner jets. Lift off a burner head. Fit the
pressure gauge to the jet. Turn on the hotplate burner
and turn on and light one of the other burners.
Reassemble burner top, making sure it is reassembled
in the correct way on the burner body.
A jet, B internal injector, C external injector
Remove burner caps and heads. Remove old jets. Fit
new jets (see Technical Data section at the back of the
book for correct jets). Reassemble in reverse order.
Check the appliance is gas sound.
Check operation of all the burners.
Tap adjustment
Pull off all the control knobs. If the hand rail has been
fitted remove it - remove the plastic blanking plugs and
remove the 2 end bracket fixing screws.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Servicing Notes
When servicing or replacing gas carrying components
disconnect from gas before commencing operation and
check appliance is gas sound after completion. When
checking for gas leaks use a liquid leak detector at all
joints and connections to check for leaks in the system.
Use a product specifically manufactured for leak
detection. Leak testing of the appliance shall be
conducted in accordance to the manufacturer’s
instructions.
CAUTION: DO NOT USE A FLAME TO CHECK
FOR GAS LEAKS.
Do not use re-conditioned or unauthorised gas
controls.
A Cooktop front fixing screws
B Cooktop rear fixing screws
Disconnect from electricity supply before commencing
servicing, particularly before removing any of the
following: control panel, side panels, cooktop tray, or
any of the electrical components or cover boxes.
Before electrical reconnection check that the appliance
is electrically safe.
Remove the 2 rear cooktop fixing screws (B) and the 4
front cooktop fixing screws (A).
Remove the screws holding the flue grille stays.
Lift the cooktop clear of the appliance. Replace in
reverse order.
Reassemble in reverse order ensuring that the leads
are reconnected.
1. To Remove the Hand Rail
Check for correct burner operation.
4. To Remove a Side Panel
Disconnect from electricity supply.
Remove control panel (see 2). Pull the cooker forward.
Remove the 4 retaining screws for each panel (2 at the
front and 2 at the rear). The lower front retaining
screws (one each side) are situated beneath the lower
edge at the front corners of the side panels
Remove the handrail plastic blanking plugs and
remove the 2 end bracket fixing screws.
2. To Remove Control Panel
Disconnect from electricity supply.
Reassemble in reverse order.
Pull off all the control knobs. Remove the hand rail
(see 2) Remove the 2 cross headed screws that were
hidden by the hand rail end brackets.
5. To Remove Oven Light Switch
Remove control panel (see 2).
NB The old switch may be destroyed during removal.
Remove switch button and old switch from its bezel by
gripping the switch body behind the control panel and
twisting sharply.
The switch bezel can then be removed by folding back
its locking wings and pushing forward. Fit the new
bezel to the control panel by first lining up the raised
key on its body with the cutout in the control panel and
pushing it in from the front. Assemble the new switch to
the bezel by lining up the key sections and pushing
home. Fit the new button by pushing in from the front.
Open the grill door and R H oven door and remove the
2 screws underneath the control panel.
Pull the control panel forward and support so that the
wires are not strained.
Replace control panel in reverse order and test for
correct operation.
Reassemble in reverse order. When replacing leads
refer to the wiring diagram. Check operation of timer,
ignition, and oven light switches.
6. To Remove Electronic Timer
Disconnect from electricity supply.
3. To Remove the Hotplate top
Pull off the timer control buttons and remove the
control panel (See 2). Remove the timer/mounting
bracket assembly from the control panel by removing
the two fixing screws. Remove the timer from its
mounting bracket by depressing the plastic lugs on the
timer case, at the same time pulling the unit forward.
Disconnect from electricity supply.
Remove the pan supports, cooktop burner caps and
tops. If there are screws holding the cooktop burners to
the cooktop, remove them (not the spark electrode
fixing screws).
Reassemble in reverse order. When replacing leads
refer to the wiring diagram. Check operation of timer.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
lead. Fit new electrode to the lead. Fix electrode in
burner with screw. Replace burner cap. Check the
burner ignition. Replace grates.
7. To Remove A Thermostat
Remove control panel (see 2) and cooktop (see 3).
Open the appropriate oven door and remove the oven
shelves.
12. To Remove or Change a Hotplate Burner.
RH oven
Remove the cooktop tray (see 3).
Remove oven roof. Remove the two fixings that secure
the thermostat phial cover. Unclip the thermostat phial
from the clips in the oven back panel & remove from
the top rear of the oven.
Centre Hotplate burners
Remove the control panel (see 2). The burners are
mounted in 2’s on cross supports. Disconnect the
burner feed pipes at the burners. Remove the screw at
the front holding the cross support. Slide the support to
the right to release in from the rear location.
LH oven
Remove the two screws holding the thermostat phial to
the oven fan cover at the rear of the oven. Pull the unit
forward to access the rear of the cooker. Remove both
rear cover boxes by removing the fixing screws and
lifting clear. Feed the thermostat capillary clear of the
oven. Disconnect the wires from the thermostat and
undo the two fixings that secure the control to the
mounting plate. Fit the replacement and re-assemble in
reverse order. Ensure that the phial is clipped to the
oven rear, positioned centrally between the clips.
Check that the thermostat functions correctly.
8. To Change Grill Controller
Remove the control panel (see 2) and cooktop (see 3).
Disconnect wiring from controller. Remove 2 screws
holding switch/controller to mounting panel. Fit new
controller and reassemble in reverse order. Check for
correct operation.
Lift the cross support and burners clear. The burners
are fixed to the cross supports with screws underneath
Remove the appropriate burner and fit the new one.
Reassemble in reverse order. Check burner operation
is satisfactory.
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS TURN OFF GAS SUPPLY.
Wok burners
Disconnect the burner feed pipes at the burner. Fit the
new one and reassemble in reverse order. Check
burner operation is satisfactory.
9. To Change a Hotplate Tap
Remove the cooktop top, see 3. Undo the nut at rear of
the valve and remove the screw(s) securing valve to
gas rail. Remove old valve, discard old gasket/seal. Fit
new gasket/seal to new valve.
13. To Remove Grill Outer Door Panel
Open left hand oven door and remove 2 screws from
bottom edge of grill door. Open grill door, support grill
door outer panel and remove two screws from top inner
face of grill door.
Reassemble in reverse order. Check valve is adjusted
for correct gas. Check cooker is gas sound.
10.To Change a Hotpate burner jet
Reassemble in reverse order.
14.To Remove an Oven Door
Open oven door and remove Handyrack (where fitted)
by springing one side out of the bracket on the door
and sliding the other side free. Support the door and
remove the two screws securing the upper hinge and
packing to the cooker front. Remove the door from the
lower hinge by lifting slightly and moving outwards.
Reassemble in reverse order.
Remove burner cap and head. Remove old jet. Fit new
orifice. Note the Wok burner has 2 orifices.
Reassemble in reverse order. Check appliance is gas
sound.
11.To Change Hotplate Burner Electrode
Lift off cooktop grates, remove burner cap. Remove the
screw holding the electrode. Pull electrode vertically up
sufficiently to grip the lead between thumb and
forefinger. Pull off the electrode, but keep hold of the
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
15. To Change Oven Door Outer Panel
17.To Change Oven Door Seal
Open oven door. The seal is held in place by small
hooks on the rear face. At the corner pull seal
diagonally away from the door centre until that hook is
released. Proceed to the next hook and release it in a
similar way, and so on.
Remove the two plastic blanking plugs from the door
handles. Remove the 4mm Hex headed screws holding
the handle to the door with the hexagon key tool.
Remove two screws from top edge and two from
bottom edge of the door.
Remove outer door panel. Fit door handle to new
panel. Fit the plastic blanking plugs to the fixing holes.
Fig. 4
When fitting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes
of the door, and proceed round the door snapping in
each hook in turn.
The handles should be above the fixings.
Fit panel to door. If replacing the outer panel on the
right hand door (with the Thermodial) take care to
make sure the sensor of the Thermodial is sealed to
the door by the rubber grommet.
18.To Adjust Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep,
and screw in or out as required until required fit is
obtained. Retighten locking nut.
19.To Change Ignition Generator
Disconnect from electricity supply.
Pull cooker forward to gain access to the cover box at
the rear of the left hand cooker. Remove the screws
securing the cover and lift clear. Pull off all the leads to
the generator noting their positions. Slacken the two
screws holding generator to cooker and remove
generator.
Fit new generator to cooker and replace leads.
Reassemble in reverse order. Refer to wiring diagram.
Check ignition performance.
Reassemble in reverse order.
16. To Change Oven Door Catch
Remove outer door panel (see 15). Remove screws ‘B’
holding catch assembly to inner door panel. Fit new
catch and reassemble in reverse order.
Check correct door operation.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
the leads and connect to the replacement elements
and re-assemble parts in reverse order. Check
operation of grill.
20. To Remove Oven Inner Back.
Open the oven door. Remove oven furniture. For the
LH oven unscrew the 2 thermostat phial fixing screws.
25 To Remove the LH Oven Bottom and Top
Elements
Disconnect from the electricity supply.
Bottom Element
Pull the cooker forward to access the cover boxes at
the rear of the unit. Remove the fixings that secure the
cover and lift it clear.
Remove the fixings that secure the inner back to the oven rear.
Lift the removable panel away. Re-assemble in reverse
order. Ensure that the retaining fixings are fully
tightened. For the LH oven unscrew the 2 thermostat
phial fixing screws. Remove the screws that secure the
inner back to the oven rear. Lift the removable panel
away. Re-assemble in reverse order. Ensure that the
retaining fixings are fully tightened.
Remove the 2 screws ‘A’ and allow the plate to drop
down.
22.To Replace an Oven Fan
Disconnect from electricity supply.
Pull the unit forward to access the cover boxes at the
rear of the appliance. Remove the fixings that secure
the cover and lift it clear. Remove the fan wiring, noting
the connection positions. Remove the inner back as
detailed in Section 20. Hold the fan blades and undo
the centre nut (LH thread), brass washers, fan blade
and Circlip. Undo the fixings that retain the fan and
remove it from the cavity rear. Fit the replacement and
re-assemble parts in reverse order. Check that the
oven operates satisfactorily.
Remove the 2 screws B, holding the element to the
bottom sheet..
Disconnect the leads, noting their positions.
23.To Remove an Oven fan Element
Withdraw bottom element. Fit the new element and re-
assemble parts in reverse order.
Disconnect from electricity supply.
Remove the inner back as detailed in Section 20.
Remove the fixings that secure the element within the
oven and lift the element away carefully. Disconnect
the leads and connect to the replacement element and
re-assemble parts in reverse order. Check that the
oven operates correctly.
Top Element
Open the LH oven door and undo the fixings that
secure the heat shield. Remove the top element
bracket fixings and withdraw element. Replace the
element and re-assemble parts in reverse order. Check
that the oven operates satisfactorily.
24.To Remove Grill Element.
Disconnect from electricity supply.
26.To change oven light bulb.
Disconnect from the electricity supply.
Remove grill pan from grill chamber. From inside grill
compartment remove enamelled front shield from grill
roof, 2 screws and washers. Remove 2 screws and
washers securing the grill element front support.
Remove 1 screw from each of the grill elements and
withdraw grill elements from grill chamber. Disconnect
Remove the oven furniture. Unscrew the bulb.
Fit an Edison screw fitting 15w 125-130v lamp, FOR
OVENS. It must be a special bulb, heat resistant to 300
°C.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Circuit Diagram
A
B
C
D
F
Grill energy regulator
Colour Code
b Blue
Left hand Multi function oven thermostat
Multi function oven function control
Clock
br Brown
or Orange
Right hand oven thermostat
Grill elements
r
Red
G
H
I
v
w
y
Violet
White
Yellow
Multi function oven base element
Multi function oven top element (outer pair)
Multi function oven browning element (inner pair)
Multi function oven fan element
Multi function oven fan
Right hand fan oven element
Right hand oven fan
J
K
M
O
P
Q
R
S
T
Oven light switch
Oven light
Ignition switch
Ignition generator
U
V
Cut-out
Neon
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
This cooker is category II2H3+
It is supplied set for group H natural gas.
A conversion kit from NG to LP gas is included.
INSTALLER: Please leave these instructions with the User.
DATA BADGE LOCATION:
Country of Destination: GB/IE
Gas
Cooker back, serial number repeater badge below oven door opening.
Electric
Natural Gas
Butane
Propane
20mbar
29mbar
37mbar
220 - 240V 50Hz
(See appliance data badge for test pressures)
Dimensions
Overall height
minimum 898mm maximum 925mm
Overall width
1100mm See ‘Positioning of Cooker’
Overall depth
648mm
Space for fixing
Minimum space above hotplate
See ‘Positioning of Cooker’
650mm
Connections
Gas:
Electric
220 - 240V 50Hz
Rp 1/2 at rear right-hand side
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Ratings
Natural Gas
Injector
L.P. Gas
Injector
Hotplate
Wok burner
3.65kW internal 80
external 129
3.0kW 134
1.7kW 109
1.0kW 75
3.5kW (246g/h) internal 54
external 77
3.0kW (210g/h) 87
1.7kW (119g/h) 68
1.0kW (70g/h) 51
Large Burner
Medium Burners
Small Burner
Gas burner inputs based on Gross Calorific Value
Ovens
Left hand Multifunction Oven
Right hand Fan Oven
Fan element
Top element
Browning Element
Bottom element
2.5kW
1.2kW
1.15kW
1.0kW
2.3kW
2.5kW
Grill
Maximum total electrical load at 230V 7.4kW*
*approximate total including oven lights, oven fan etc.
Ovens
Multifunction
Forced air convection
Energy efficiency class
on a scale of A (more efficient)
to G (less efficient)
Energy consumption
based on standard load
Usable volume (litres)
Size
B
A
0.90kWh
62
Medium
0.85kWh
67
Large
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|