Eiki Projector LC SM3 User Manual

MULTIMEDIA PROJECTOR  
MODEL  
LC-SM3  
OWNER’S MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
All the safety and operating instructions should be read before  
the product is operated.  
This projector should be operated only from the type of power  
source indicated on the marking label. If you are not sure of  
the type of power supplied, consult your authorized dealer or  
local power company.  
Read all of the instructions given here and retain them for later  
use. Unplug this projector from AC power supply before  
cleaning. Do not use liquid or aerosol cleaners. Use a damp  
cloth for cleaning.  
Do not overload wall outlets and extension cords as this can  
result in fire or electric shock. Do not allow anything to rest on  
the power cord. Do not locate this projector where the cord  
may be damaged by persons walking on it.  
Follow all warnings and instructions marked on the projector.  
For added protection to the projector during a lightning storm,  
or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet. This will prevent damage  
due to lightning and power line surges.  
Do not attempt to service this projector yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service  
personnel.  
Unplug this projector from wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the projector.  
Do not expose this unit to rain or use near water... for  
example, in a wet basement, near a swimming pool, etc...  
Do not use attachments not recommended by the  
manufacturer as they may cause hazards.  
c. If the projector has been exposed to rain or water.  
d. If the projector does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the projector to normal operation.  
e. If the projector has been dropped or the cabinet has been  
damaged.  
f. When the projector exhibits a distinct change in  
performance-this indicates a need for service.  
Do not place this projector on an unstable cart, stand, or table.  
The projector may fall, causing serious injury to a child or  
adult, and serious damage to the projector. Use only with a  
cart or stand recommended by the manufacturer, or sold with  
the projector. Wall or shelf mounting should follow the  
manufacturer's instructions, and should use a mounting kit  
approved by the manufacturers.  
An appliance and cart combination should  
be moved with care. Quick stops,  
excessive force, and uneven surfaces  
may cause the appliance and cart  
combination to overturn.  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer that have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock, or injury to persons.  
Upon completion of any service or repairs to this projector, ask  
the service technician to perform routine safety checks to  
determine that the projector is in safe operating condition.  
Slots and openings in the back and bottom of the cabinet are  
provided for ventilation, to insure reliable operation of the  
equipment and to protect it from overheating.  
The openings should never be covered with cloth or other  
materials, and the bottom opening should not be blocked by  
placing the projector on a bed, sofa, rug, or other similar  
surface. This projector should never be placed near or over a  
radiator or heat register.  
This projector should not be placed in a built-in installation  
such as a book case unless proper ventilation is provided.  
Voor de klanten in Nederland  
Bij dit product zijn batterijen  
geleverd.  
Wanneer deze leeg zijn,  
moet u ze niet weggooien  
maar inleveren als KCA.  
Never push objects of any kind into this projector through  
cabinet slots as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the projector.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPLIANCES  
Federal Communication Commission Notice  
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures :  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.  
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such  
changes or modifications should be made, you could be required to stop operation of the equipment.  
Model Number  
Trade Name  
Responsible party  
Address  
: LC-SM3  
: EIKI  
: EIKI International, Inc.  
: 26794 Vista Terrace Drive, Lake Forest, CA 92630-8113  
Telephone No.  
: 800-242-3454 (949-457-0200)  
AC POWER CORD REQUIREMENT  
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada :  
AC Power Cord used in the United States and Canada is listed by the Underwriters  
Laboratories (UL) and certified by the Canadian Standard Association (CSA).  
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be  
sure that the plug will fit into the power outlet. Do not try to defeat this safety feature.  
GROUND  
Should you be unable to insert the plug into the outlet, contact your electrician.  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
FEATURES AND DESIGN  
6
7
COMPUTER INPUT  
22  
SELECTING INPUT SOURCE  
22  
22  
23  
SELECTING COMPUTER SYSTEM  
PREPARATION  
COMPATIBLE COMPUTER SPECIFICATIONS  
PC ADJUSTMENT  
24  
24  
25  
AUTO PC ADJUSTMENT  
MANUAL PC ADJUSTMENT  
NAME OF EACH PART OF PROJECTOR  
7
8
8
9
9
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
POSITIONING PROJECTOR  
ADJUSTABLE FEET  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT  
27  
27  
28  
IMAGE LEVEL ADJUSTMENT  
MOVING PROJECTOR  
10  
PICTURE SCREEN ADJUSTMENT  
29  
VIDEO INPUT  
30  
CONNECTING PROJECTOR  
11  
SELECTING INPUT SOURCE  
SELECTING VIDEO SYSTEM  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT  
30  
31  
32  
32  
33  
TERMINALS OF PROJECTOR  
CONNECTING TO COMPUTER  
CONNECTING TO VIDEO EQUIPMENT  
11  
12  
13  
IMAGE LEVEL ADJUSTMENT  
PICTURE SCREEN ADJUSTMENT  
34  
BEFORE OPERATION  
14  
OPERATION OF REMOTE CONTROL  
OPERATING RANGE  
14  
15  
15  
SETTING  
35  
REMOTE CONTROL BATTERY INSTALLATION  
SETTING MENU  
35  
TOP CONTROLS AND INDICATORS  
16  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
17  
17  
17  
18  
APPENDIX  
37  
MAINTENANCE  
37  
37  
37  
37  
38  
38  
WARNING TEMP. INDICATOR  
AIR FILTER CARE AND CLEANING  
CLEANING PROJECTION LENS  
LAMP REPLACEMENT  
BASIC OPERATION  
19  
TURNING ON / OFF PROJECTOR  
19  
LAMP REPLACE COUNTER  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
20  
20  
20  
20  
20  
21  
21  
TROUBLESHOOTING  
TECHNICAL SPECIFICATIONS  
39  
41  
FOCUS ADJUSTMENT  
KEYSTONE ADJUSTMENT  
PICTURE FREEZE FUNCTION  
NO SHOW FUNCTION  
P-TIMER FUNCTION  
SOUND ADJUSTMENT  
21  
TRADEMARKS  
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.  
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.  
Windows and PowerPoint are registered trademarks of Microsoft Corporation.  
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its  
respective corporation.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES AND DESIGN  
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This  
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)  
technology.  
Compact Design  
One-Touch Auto PC Adjustment  
This projector is extremely compact in size and weight.  
It is designed to carry and work anywhere you wish to  
use.  
Incoming computer video signals are recognized and the  
best adjustment is automatically set by Auto PC  
Adjustment. No complicated setup is necessary and  
projection is always precise.  
Compatibility  
Digital Zoom (for Computer)  
This projector widely accepts various video and  
computer input signals including;  
Digital Zoom function expands (to approx. 16 times of  
screen size) or compress the image size, allowing you to  
focus on crucial information at a presentation.  
Computers  
IBM-compatible or Macintosh computer up to 1280  
x 1024 resolution.  
6 Color Systems  
Keystone Correction  
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-  
N color system can be connected.  
Positioning height of a projector may result in distorted  
image being displayed in a trapezoid shape. Keystone  
Correction solves this problem by digitally altering  
projection to produce undistorted images.  
Component Video  
Component video signal, such as a DVD player  
output, high definition TV signals including 480i,  
480p, 575i, 575p, 720p, 1035i or 1080i, can be  
connected.  
Power Management  
S-Video  
Power Management function is provided to reduce power  
consumption while a projector is not in use.  
S-Video signal, such as a S-VHS VCR output  
signal, can be connected.  
This Power Management function operates to turn  
Projection Lamp off when a projector detects signal  
interruption and any button is not pressed over 5  
minutes. Projection Lamp is automatically turned on  
again when a projector detects signal or any operation  
button is pressed.  
High Resolution Image  
This projector provides 800 x 600 dots resolution for  
computer input and 500 horizontal TV lines. Resolution  
from a computer between SVGA (800 x 600) and SXGA  
(1280 x 1024) is compressed into 800 x 600 dots. This  
projector cannot display image of over 1280 x 1024 dots.  
When resolution of your computer is higher than 1280 x  
1024, reset a computer output for lower resolution.  
This projector is shipped with this function ON.  
Multilanguage Menu Display  
Operation menu is displayed in; English, German,  
French, Italian, Spanish, Portuguese, Dutch, Swedish,  
Chinese, Korean or Japanese.  
Multi-Scan System  
This projector has Multi-Scan System to conform to  
almost all computer output signals quickly. There is no  
need for troublesome manual adjustment of frequency  
and other settings.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
NAME OF EACH PART OF PROJECTOR  
INFRARED  
REMOTE RECEIVER  
FRONT  
POWER CORD CONNECTOR  
PROJECTION LENS  
FOCUS RING  
EXHAUST VENTS  
HOT AIR EXHAUSTED !  
ZOOM LEVER  
LENS CAP  
Air blown from Exhaust Vents is hot. When using or  
installing projector, following precautions should be taken.  
Do not put any flammable object near these vents.  
Keep front grills at least 3(1m) away from any object,  
especially heat-sensitive object.  
Do not touch this area, especially screw and metallic part.  
This area will become hot while a projector is used.  
This projector detects internal temperature and  
automatically controls running speed of Cooling Fans.  
BACK  
TOP CONTROLS  
AND INDICATORS  
TERMINALS  
AND CONNECTORS  
AIR INTAKE VENTS  
This projector is equipped with Cooling  
Fans for protection from overheating.  
Pay attention to the following to ensure  
proper ventilation and avoid a possible  
risk of fire and malfunction.  
SPEAKER  
Do not cover vent slots.  
BOTTOM  
Keep back and bottom clear of any  
object. Obstructions may block  
cooling air.  
AIR INTAKE VENTS  
AND AIR FILTERS  
ADJUSTABLE FEET  
AND  
FEET LOCK LATCHES  
LAMP COVER  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
This projector uses nominal input voltages of 100-120 V or 200-240  
V AC. This projector automatically selects the correct input  
voltage. It is designed to work with single-phase power systems  
having a grounded neutral conductor. To reduce risk of electrical  
shock, do not plug into any other type of power system.  
Consult your authorized dealer or service station if you are not sure  
of the type of power supply being in use.  
Connect a projector with a peripheral equipment before turning a  
projector on. (Refer to pages 11 ~ 13 for connection.)  
CAUTION  
For safety, unplug AC Power Cord when an appliance is not  
used.  
When this projector is connected to the outlet with AC Power  
Cord, an appliance is in Stand-by Mode and consumes a little  
electric power.  
Connect AC Power Cord (supplied) to a projector.  
The AC outlet must be near this equipment and  
must be easily accessible.  
NOTE ON THE POWER CORD  
AC Power Cord must meet requirement of the country where you use a projector.  
Confirm an AC plug type with the chart below and proper AC Power Cord must be used.  
If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.  
Projector side  
AC Outlet side  
For the U.S.A. and Canada For Continental Europe  
Ground  
To POWER CORD  
CONNECTOR on your  
projector.  
To the AC Outlet.  
(120 V AC)  
To the AC Outlet.  
(200 - 240 V AC)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
POSITIONING PROJECTOR  
This projector is designed to project on a flat projection surface.  
The projector can be focused from 5.3(1.6m) ~ 26.6(8.1m).  
Refer to the figure below to adjust a screen size.  
ROOM LIGHT  
The brightness in a room has a great influence on  
picture quality. It is recommended to limit  
ambient lighting in order to provide the best  
image.  
26.6(8.1m)  
20.0(6.1m)  
200”  
13.1(4.0m)  
150”  
Max. Zoom  
5.3(1.6m)  
166”  
Min. Zoom  
100”  
83”  
H1  
H2  
123”  
40”  
34”  
34”  
40”  
100”  
150”  
200”  
Screen Size  
(W x H) mm  
690.9 x 518.2  
812.8 x 609.6  
2032 x 1524  
57(1447.8mm)  
3(76.2mm)  
3048 x 2286  
4064 x 3048  
19.4(492.3mm) 22.8(579.12mm)  
1.0(25.9mm) 1.2(30.48mm)  
85.5(2171.7mm) 114(2895.6mm)  
Height (H1)  
Height (H2)  
4.5(114.3mm)  
6(152.4mm)  
ADJUSTABLE FEET  
Picture tilt and projection angle can be adjusted by rotating  
ADJUSTABLE FEET. Projection angle can be adjusted to 10.6  
degrees.  
Lift the front of a projector and pull FEET LOCK LATCHES  
on the both sides of a projector.  
1
Release FEET LOCK LATCHES to lock ADJUSTABLE FEET  
and rotate ADJUSTABLE FEET to adjust position and tilt.  
2
To retract ADJUSTABLE FEET, lift the front of a projector  
and pull and undo FEET LOCK LATCHES.  
Keystone distortion of a projected image can be adjusted by  
Menu Operation. (Refer to P20 and 35.)  
3
CAUTION  
FEET LOCK  
LATCHES  
ADJUSTABLE FEET  
Avoid positioning a projector with the angle of more than 20  
degrees. Projection Lamp may malfunction.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
MOVING PROJECTOR  
When moving a projector, replace Lens Cap and retract Adjustable Feet to prevent damage to the lens and cabinet.  
When the projector is not in use for an extended period, put it into the case (carrying bag) supplied with the projector.  
CAUTION  
Carrying Bag (supplied) is intended for protection from dust and scratches on the surface of a cabinet, and it is not designed  
to protect an appliance from external forces. Do not transport a projector through a courier or transport services with this  
bag, otherwise the projector can be damaged. When handling a projector, do not drop, bump, subject it to strong forces or  
put other things on the cabinet.  
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR  
Do not drop or bump a projector, otherwise damages or malfunctions may result.  
When carrying a projector, use a suitable carrying case.  
Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause  
damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best  
way.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
TERMINALS OF PROJECTOR  
This projector has input and output terminals on its side for connecting computers and video equipment. Refer to figures on  
pages 11 to 13 and connect properly.  
USB CONNECTOR (Series B)  
RESET BUTTON  
VIDEO INPUT JACKS  
When controlling the computer This projector uses a micro  
with Remote Control Unit of this processor to control this unit,  
projector, connect USB port of and occasionally, this micro  
your personal computer to this processor may malfunction  
Connect the composite video  
output from video equipment  
to VIDEO/Y jack or connect  
the component video outputs  
to VIDEO/Y, Pb/Cb and  
Pr/Cr jacks. (Refer to P13.)  
connector. (Refer to P12.)  
and need to be reset. This  
can be done by pressing  
RESET button with a pen,  
which will shut down and  
restart the unit. Do not use  
RESET function excessively.  
S-VIDEO INPUT JACK  
Connect the S-VIDEO  
output from video  
equipment to this  
jack. (Refer to P13.)  
CONTROL PORT CONNECTOR  
VIDEO  
Y
Pb / Cb Pr / Cr  
When controlling the computer  
with Remote Control Unit of  
this projector, connect the  
mouse port of your personal  
computer to this connector.  
(Refer to P12.)  
RESET  
USB  
CONTROL PORT  
SVIDEO  
COMPUTER  
AUDIO IN  
COMPUTER INPUT  
AV  
COMPUTER IN  
TERMINAL (ANALOG)  
Connect the computer  
output to this jack.  
AUDIO OUT  
(Refer to P12.)  
COMPUTER AUDIO  
AUDIO OUTPUT JACK  
AUDIO INPUT JACK  
INPUT JACK  
Connect an external  
audio amplifier to this  
jack.  
Connect the audio output  
from video equipment to  
this jack.  
Connect the audio output  
(stereo) from computer to  
this jack. (Refer to P12.)  
(Refer to P12, 13.)  
(Refer to P13.)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO COMPUTER  
Cables used for connection (= Cable or adapter is not supplied with this projector.)  
VGA Cable (HDB 15 pin)  
MAC Adapter (When connecting to Macintosh computer)  
Audio Cable (Mini Plug (stereo) x 1)  
Control Cable for PS/2 Port , Serial Port , or ADB Port ●  
USB Cable ●  
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)  
Desktop type  
Monitor Output  
Laptop type  
Serial port PS/2 port  
ADB port  
Audio Output USB port  
MAC Adapter  
Set slide switches  
according to the  
chart below.  
Control Cable  
Control Cable  
Control Cable  
for Serial Port for PS/2 Port for ADB Port ●  
USB  
Cable  
Terminal  
Terminal  
Terminal  
Audio  
Cable ●  
(stereo)  
VGA Cable  
Use one of these Control  
USB  
COMPUTER AUDIO IN  
Cables or USB Cable  
corresponding with the  
terminal of your computer.  
CONTROL PORT  
COMPUTER IN ANALOG  
VIDEO  
Y
Pb / Cb  
Pr / Cr  
RESET  
USB  
CONTROL PORT  
SVIDEO  
COMPUTER  
AUDIO IN  
AV  
COMPUTER IN  
AUDIO OUT  
Terminals  
of the Projector  
AUDIO OUT  
NOTE :  
When connecting the cable, the power  
cords of both the projector and the external  
equipment should be disconnected from  
AC outlet. Turn the projector and  
peripheral equipment on before the  
computer is switched on.  
Audio Cable  
(stereo) ●  
MAC ADAPTER (Not supplied)  
Set switches as shown in the table  
below depending on RESOLUTION  
MODE that you want to use before  
you turn on projector and computer.  
ON  
ON  
DIP  
1
2
3
4
5
6
Audio Input  
External Audio Equipment  
Audio Speaker  
OFF  
3
1
2
4
5
6
Audio Amplifier  
13" MODE (640 x 480)  
ON  
ON OFF OFF OFF OFF  
(stereo)  
16" MODE (832 x 624) OFF ON OFF ON OFF OFF  
19" MODE (1024 x 768) OFF ON  
21" MODE (1152 x 870) ON ON  
ON OFF OFF OFF  
ON ON OFF OFF  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO VIDEO EQUIPMENT  
Cables used for connection (= Cable is not supplied with this projector.)  
Video Cable (RCA x 1 or RCA x 3) ●  
S-VIDEO Cable ●  
Audio Cable (Mini Plug (stereo) x 1) ●  
Component video output equipment.  
(such as DVD player or high-definition  
Video Source (example)  
Video Cassette Recorder  
Video Disc Player  
TV source.)  
Audio Output  
Component Video Output  
(Y, Pb/Cb, Pr/Cr)  
Composite  
Video Output  
S-VIDEO Output  
Audio Cable  
(stereo)  
Video Cable  
(RCA x 1) ●  
Video Cable  
(RCA x 3) ●  
S-VIDEO  
Cable ●  
Use any of VIDEO jack Y-Pb/Cb-  
Pr/Cr jacks or S-VIDEO jack.  
When both VIDEO jack and S-  
VIDEO jack are connected, S-  
VIDEO jack has priority over  
VIDEO jack.  
VIDEO  
AUDIO IN  
S-VIDEO  
Y - Pb/Cb - Cr/Pr  
When both Y-Pb/Cb-Pr/Cr jacks  
and S-VIDEO jack are connected,  
Y-Pb/Cb-Pr/Cr jacks has priority  
over S-VIDEO jack.  
VIDEO  
Y
Pb / Cb  
Pr / Cr  
RESET  
USB  
CONTROL PORT  
SVIDEO  
COMPUTER  
AUDIO IN  
AV  
COMPUTER IN  
AUDIO OUT  
AUDIO OUT  
Terminals  
of the Projector  
Audio Cable  
(Stereo) ●  
Audio Input  
External Audio Equipment  
NOTE :  
Audio Speaker (stereo)  
Audio Amplifier  
When connecting the cable, the power  
cords of both the projector and the external  
equipment should be disconnected from  
AC outlet.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
OPERATION OF REMOTE CONTROL  
Infrared signals are transmitted from this point.  
INPUT BUTTON  
POWER ON-OFF BUTTON  
ON–OFF  
INPUT  
Used to select input source.  
(P22, 30)  
Used to turn the projector  
on or off. (P19)  
D.ZOOM BUTTONS  
VOLUME BUTTONS  
Used to select DIGITAL  
ZOOM mode and resize the  
image. (P29)  
Used to adjust volume.  
(P21)  
KEYSTONE D.ZOOM  
VOLUME  
+
POINT BUTTONS  
KEYSTONE BUTTONS  
Used to move the pointer on  
the MENU, to adjust the  
item, or to pan the image in  
DIGITAL ZOOM mode.  
(P29)  
Used to correct the  
keystone distortion.  
(P20, 35)  
MENU  
SELECT  
MENU BUTTON  
Used to select MENU  
operation. (P17, 18)  
SELECT BUTTON  
FREEZE BUTTON  
Used to execute the item  
selected or to expand /  
compress the image in  
DIGITAL ZOOM mode.  
(P29)  
NOSHOW FREEZE  
MUTE  
Used to freeze the picture.  
(P20)  
AUTO PC ADJ. P–TIMER  
IMAGE  
NO SHOW BUTTON  
Used to turn the picture into  
black image. (P21)  
MUTE BUTTON  
Used to mute sound.(P21)  
AUTO PC ADJ. BUTTON  
IMAGE BUTTON  
Use to operate Auto PC  
Adjustment function. (P24)  
Used to select image level.  
(P27, 32)  
P-TIMER BUTTON  
Used to operate P-TIMER  
function. (P21)  
Battery is installed in Remote  
Control Unit.  
Before operation, pull out and  
remove a protect sheet from  
Remote Control Unit. This sheet  
protecting discharge of a battery.  
To insure safe operation, please observe the following  
precautions :  
Do not bend, drop Remote Control Unit, or expose  
Remote Control Unit to moisture or heat.  
For cleaning, use soft dry cloth. Do not apply  
benzene, thinner, splay or any chemical material.  
AUTO PC ADJ. PTIMER  
IMAGE  
Pull and remove.  
BATTERY PROTECT SHEET  
(transparent sheet)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
OPERATING RANGE  
Point Remote Control Unit toward projector (Receiver  
Window) whenever pressing any button. Maximum  
operating range for Remote Control Unit is about 16.4(5m)  
and 60° in front of the projector.  
16.4’  
(5 m)  
30°  
30°  
REMOTE CONTROL BATTERY INSTALLATION  
Replace with new battery. Install  
with battery (+),() marks properly.  
Install battery and  
Battery Holder into  
Remote Control Unit.  
Pull out Battery Holder.  
1
2
3
Put Battery + mark  
as shown direction.  
BATTERY  
LITHIUM BATTERY  
CR2025 (3.0V)  
(+) mark indicates  
its (+) polarity.  
BATTERY HOLDER  
To insure safe operation, please observe the following precautions :  
Use only specified battery. Improper battery may cause malfunction of Remote Control or improper battery's  
installation may cause explosion.  
Be sure to install battery with correct polarity.  
Do not expose a battery to moisture or heat. Do not charge a battery.  
If a battery have leaked on Remote Control Unit, carefully wipe the case clean and load a new battery.  
Dispose used battery according to the battery-manufacturer's instructions.  
Keep a battery away from children to avoid swallowing it accidentally.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
TOP CONTROLS AND INDICATORS  
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.  
LAMP INDICATOR  
Becomes dim when the  
projector is turned on.  
And bright when the  
projector is in stand-by  
mode.  
POWER ONOFF BUTTON  
Used to turn the projector  
on or off. (P19)  
READY INDICATOR  
LAMP  
INPUT BUTTON  
Lights green when the  
projector is ready to be  
Used to select input  
source. (P22, 30)  
turned on.  
And it  
READY  
flashes green in Power  
Management mode.  
(P36)  
ON OFF  
WARNING  
TEMP .  
INPUT  
LAMP  
REPLACE  
WARNING TEMP. INDICATOR  
MENU  
MENU BUTTON  
Flashes red when  
internal  
temperature is too  
high. (P37)  
projector  
Used to open or close  
MENU operation. (P17,  
18)  
-VOLUME-  
SELECT  
IMAGE  
LAMP REPLACE INDICATOR  
IMAGE BUTTON  
Turns to yellow when  
the life of the projection  
lamp draws to an end.  
(P38)  
Used to select image  
level. (P27, 32)  
SELECT BUTTON  
POINT (VOLUME + / ) BUTTONS  
Used to execute the item  
selected. It is also used  
to expand / compress  
the image in DIGITAL  
ZOOM mode. (P29)  
Used to select an item or adjust  
value in ON-SCREEN MENU. They  
are also used to pan the image in  
DIGITAL ZOOM +/mode. (P29)  
POINT LEFT/RIGHT buttons are  
also used as VOLUME +/buttons.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
You can control and adjust this projector through ON-SCREEN  
MENU. Refer to the following pages to operate each adjustment  
on ON-SCREEN MENU.  
WIRELESS REMOTE CONTROL  
POINT BUTTON  
MENU BUTTON  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
1 DISPLAY MENU  
Press MENU button to display ON-SCREEN MENU.  
2 MOVING POINTER  
SELECT BUTTON  
Move the pointer (see below) or adjust the value of item by  
pressing POINT button(s) on Top Control or on Remote Control  
Unit.  
Used to select the item.  
TOP CONTROL  
MENU BUTTON  
Pointer is the icon on ON-SCREEN MENU to select the item.  
See the figures on the section "FLOW OF ON-SCREEN MENU  
OPERATION" below.  
POINT BUTTONS  
MENU  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
-VOLUME-  
SELECT  
3 SELECT ITEM  
IMAGE  
Select the item or set selected function by pressing SELECT  
button.  
SELECT BUTTON  
Used to select the item.  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
MENU ICON  
Display ON-SCREEN MENU  
Press MENU button to display ON-SCREEN MENU (MENU  
BAR). A red frame is POINTER.  
1
POINTER  
(red frame)  
POINTER (red frame)  
Press POINT DOWN button to  
move POINTER.  
Select Menu to be adjusted  
Move POINTER (red frame) to MENU ICON that you want to  
select by pressing POINT RIGHT / LEFT buttons.  
2
ITEM  
Control or adjust item through ON-SCREEN MENU  
Press POINT DOWN button and move POINTER (red frame  
or red arrow) to ITEM that you want to adjust, and then press  
SELECT button to show ITEM DATA.  
3
SELECT  
BUTTON  
Adjust ITEM DATA by pressing POINT RIGHT / LEFT  
buttons.  
Refer to the following pages for details of respective  
adjustments.  
4
ITEM DATA  
Press POINT LEFT/RIGHT  
buttons to adjust value or  
set function.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
MENU BAR  
FOR PC SOURCE  
Press MENU BUTTON while connecting to PC input source.  
IMAGE SELECT MENU  
SCREEN MENU  
SETTING MENU  
Used to select  
Used to adjust size  
of image. [Normal  
/ True / Wide /  
Digital zoom +/]  
(Refer to P29)  
Used to change  
settings of projector  
or reset Lamp  
Replace Counter.  
(Refer to P35, 36)  
GUIDE WINDOW  
PC SYSTEM MENU  
image level among  
Standard, Real  
and Image 1 ~ 4.  
(Refer to P27)  
Shows selected  
item of ON-  
SCREEN MENU.  
Used to select  
computer system.  
(Refer to P22, 23)  
INPUT MENU  
PC ADJUST MENU  
IMAGE ADJUST MENU  
SOUND MENU  
Used to select  
input source either  
Computer or  
Video.  
Used to adjust  
parameters to  
match with input  
signal format.  
Used to adjust computer  
image.  
Used to adjust  
volume or mute  
sound.  
[Contrast / Brightness  
/
Color / Tint / White balance  
(R/G/B) / Sharpness /  
Gamma]  
(Refer to P21)  
(Refer to P22)  
(Refer to P24-26)  
(Refer to P28)  
FOR VIDEO SOURCE  
Press MENU BUTTON while connecting to VIDEO input source.  
INPUT MENU  
Used to select  
input source  
either Video or  
Computer.  
IMAGE SELECT MENU  
SCREEN MENU  
Used to select image  
level among  
Standard, Cinema  
and Image 1 ~ 4.  
(Refer to P32)  
Used to set size of  
image to Normal  
or Wide.  
(Refer to P30)  
(Refer to P34)  
AV SYSTEM MENU  
IMAGE ADJUST MENU  
Same function as  
Menu for PC source.  
Same function as  
Menu for PC source.  
Used to select  
system of selected  
video source.  
Used to adjust picture image.  
[Contrast / Brightness / Color /  
Tint / White balance (R/G/B) /  
Sharpness / Gamma]  
(Refer to P31)  
(Refer to P33, 34)  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
TURNING ON / OFF PROJECTOR  
TURNING ON PROJECTOR  
Complete peripheral connections (with Computer, VCR, etc.)  
before turning on projector. (Refer to "CONNECTING TO  
PROJECTOR" on pages 11~13 for connecting that equipment.)  
1
Connect the projector's AC Power Cord into an AC outlet. LAMP  
Indicator lights RED, and READY Indicator lights GREEN.  
30  
2
3
Press POWER ON-OFF button on Top Control or on Remote  
Control Unit to ON. LAMP Indicator dims, and Cooling Fans  
start to operate. Preparation Display appears on a screen and  
the count-down starts. The signal from PC or Video source  
appears after 30 seconds.  
Preparation Display disappears after 30 seconds.  
TURNING OFF PROJECTOR  
Press POWER ON-OFF button on Top Control or on Remote  
Control Unit, and a message "Power off?" appears on a screen.  
1
2
Press POWER ON-OFF button again to turn off projector. LAMP  
Indicator lights bright and READY Indicator turns off. After  
projector is turned off, Cooling Fans operate (for 90 seconds).  
During this "Cooling Down" period, the projector cannot be  
turned on.  
Power off?  
When projector has cooled down, READY Indicator lights  
GREEN again and you can turn projector on. After cooling down  
completely, disconnect AC Power Cord.  
Message disappears after 4 seconds.  
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN  
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE  
TURNING IT OFF.  
When Power Managementfunction is ON, projector detects signal interruption and turns off Projection Lamp automatically.  
Refer to Power Managementon page 36.  
When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on  
projector again.  
When WARNING TEMP. Indicator continues to flash, follow procedures below:  
1. Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.  
2. Check Air Filters for dust accumulation.  
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 37.)  
4. Turn a projector on again.  
If WARNING TEMP. Indicator should still continue to flash, contact the sales dealer where you purchased this projector or  
service center.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
Rotate ZOOM LEVER clockwise to make the image larger. Rotate  
ZOOM LEVER counterclockwise to make the image smaller.  
ZOOM LEVER  
WIDE  
TELE  
FOCUS ADJUSTMENT  
Rotate FOCUS RING to adjust the projected picture focus.  
FOCUS RING  
KEYSTONE ADJUSTMENT  
If a projected picture has keystone distortion, correct image with KEYSTONE adjustment.  
Press KEYSTONE /button on Remote Control Unit or select  
Keystone on SETTING menu. (Refer to page 35.) Keystone  
dialog box appears.  
1
Correct keystone distortion by pressing KEYSTONE /button  
or POINT UP/DOWN button(s). Press KEYSTONE button or  
POINT UP button to reduce the upper part of image, and press  
KEYSTONE button or POINT DOWN button to reduce the  
lower part.  
2
Reduce the upper width with KEY STONE button  
or POINT UP button.  
Reduce the lower width with KEY STONE button  
or POINT DOWN button.  
PICTURE FREEZE FUNCTION  
Press FREEZE button on Remote Control Unit to freeze the picture  
on-screen. To cancel FREEZE function, press FREEZE button again  
or press any other button.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
NO SHOW FUNCTION  
Press NO SHOW button on Remote Control Unit to black out the  
image. To restore to normal, press NO SHOW button again or press  
any other button.  
No show  
Message disappears after 4 seconds.  
P-TIMER FUNCTION  
Press P-TIMER button on Remote Control unit. The timer display 00  
: 00appears on the screen and the timer starts to count time (00 : 00  
~ 59 : 59).  
To stop P-TIMER display, press P-TIMER button. And then, press P-  
TIMER button again to cancel P-TIMER function.  
SOUND ADJUSTMENT  
Indicates roughly level of  
volume.  
DIRECT OPERATION  
Volume  
Press VOLUME (+/) button(s) on Remote Control Unit or POINT  
LEFT / RIGHT button on Top Control to adjust volume. Volume dialog  
box appears on the screen for a few seconds.  
VOLUME (+) or POINT RIGHT button to increase volume, and  
VOLUME () or POINT LEFT button for decreasing.  
Mute  
Press MUTE button to set  
Mute function On or Off.  
Press MUTE button on Remote Control Unit to cut off sound. To  
restore sound to its previous level, press MUTE button again or press  
Volume (+/) or POINT LEFT / RIGHT button(s).  
The display disappears after 4 seconds.  
MENU OPERATION  
SOUND MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to  
SOUND Menu icon.  
1
SOUND Menu icon  
Press POINT DOWN button to move a red frame pointer to the  
item that you want to select, and then press SELECT button.  
2
Indicates roughly  
level of volume.  
Volume  
Close SOUND Menu.  
To increase volume, press POINT RIGHT button, and press POINT  
LEFT button for decreasing.  
Mute  
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box  
display is changed to Onand sound is cut off. To restore sound to  
its previous level, press POINT LEFT/RIGHT button(s) again.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
SELECTING INPUT SOURCE  
INPUT button  
Computer  
DIRECT OPERATION  
Choose Computer by pressing INPUT button on Top Control or on  
Remote Control Unit.  
Video  
If projector cannot reproduce proper image, select correct input source  
through MENU OPERATION (see below).  
MENU OPERATION  
INPUT MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
1
POINT LEFT/RIGHT button to move a red frame pointer to  
INPUT Menu icon.  
INPUT Menu icon  
Press POINT DOWN button to move a red arrow pointer to  
2
Computer and then press SELECT button.  
Move a pointer (red arrow)  
to Computer and press  
SELECT button.  
SELECTING COMPUTER SYSTEM  
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to  
COMPATIBLE COMPUTER SPECIFICATIONon page 23). When selecting Computer, this projector automatically tunes  
to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)  
Note : Projector may display one of the following messages.  
When projector cannot recognize connected signal as PC  
system provided in this projector, Auto PC Adjustment  
function operates to adjust projector and the message  
Autois displayed on SYSTEM Menu icon. (Refer to  
P24.) When image is not provided properly, manual  
adjustment is required. (Refer to P25 and 26.)  
PC SYSTEM MENU  
Auto  
SYSTEM Menu icon  
Displays system being  
selected.  
There is no signal input from computer. Make sure the  
connection of computer and a projector is set correctly.  
(Refer to TROUBLESHOOTING on page 39.)  
––––  
SELECT COMPUTER SYSTEM MANUALLY  
This projector automatically selects PC system among those provided  
in this projector and PC system can be also selected manually.  
PC SYSTEM MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to PC  
SYSTEM Menu icon.  
1
SYSTEM Menu icon  
Displays system being selected.  
Press POINT DOWN button to move a red arrow pointer to the  
The systems on this dialog box  
can be selected.  
2
system that you want to set, and then press  
SELECT button.  
Custom Mode (1~5) set in PC  
ADJUST Menu. (P25, 26)  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
COMPATIBLE COMPUTER SPECIFICATIONS  
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100  
MHz of Dot Clock.  
ON-SCREEN  
DISPLAY  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
VGA 1  
VGA 2  
640 x 480  
720 x 400  
640 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
31.47  
31.47  
31.47  
37.86  
37.86  
37.50  
43.269  
34.97  
35.00  
15.625  
15.734  
35.156  
37.88  
46.875  
53.674  
48.08  
37.90  
34.50  
38.00  
38.60  
32.70  
38.00  
49.72  
48.36  
68.677  
59.88  
70.09  
70.09  
74.38  
72.81  
75.00  
85.00  
66.60  
66.67  
XGA 3  
XGA 4  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 864  
1152 x 900  
60.023  
56.476  
60.31  
48.50  
44.00  
63.48  
36.00  
62.04  
61.00  
35.522  
46.90  
47.00  
58.03  
60.24  
68.68  
64.20  
61.20  
50.00  
50.00  
61.85  
46.43  
45.00  
33.75  
33.75  
75.03  
70.07  
74.92  
60.02  
54.58  
79.35  
VGA 3  
XGA 5  
VGA 4  
XGA 6  
VGA 5  
XGA 7  
VGA 6  
XGA 8  
87.17  
VGA 7  
XGA 9  
(Interlace)  
MAC LC13  
MAC 13  
RGB  
XGA 10  
XGA 11  
XGA 12  
XGA 13  
XGA 14  
XGA 15  
MAC 19  
MAC 21  
SXGA 1  
SXGA 11  
77.07  
75.70  
640 x 480  
––––––––  
50  
86.96  
(Interlace)  
(Interlace)  
60  
––––––––  
RGB  
58.20  
58.30  
72.00  
75.08  
75.06  
70.40  
65.20  
(Interlace)  
SVGA 1  
SVGA 2  
SVGA 3  
SVGA 4  
SVGA 5  
SVGA 6  
SVGA 7  
SVGA 8  
SVGA 9  
SVGA 10  
SVGA 11  
MAC 16  
XGA 1  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
56.25  
60.32  
75.00  
85.06  
72.19  
61.03  
55.38  
60.51  
60.31  
51.09  
60.51  
74.55  
60.00  
84.997  
86.00  
(Interlace)  
94.00  
(Interlace)  
SXGA 13 1280 x 1024  
SXGA 14 1280 x 1024  
SXGA 17  
1152 x 900  
66.00  
86.70  
SXGA 18 1280 x 1024  
(Interlace)  
––––––––  
720p (HDTV)  
60.00  
60.00  
––––––––  
1035i (HDTV)  
(Interlace)  
60.00  
(Interlace)  
––––––––  
1080i (HDTV)  
XGA 2  
NOTE : Specifications are subject to change without notice.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PC ADJUSTMENT  
AUTO PC ADJUSTMENT  
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your  
computer. Auto PC Adjustment function can be operated as follows.  
Auto PC Adj.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to PC  
ADJUST Menu icon.  
PC ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to  
AUTO PC Adj. icon and then press SELECT button twice.  
This Auto PC Adjustment can be also executed by pressing  
AUTO PC ADJ. button on Remote Control Unit.  
PC ADJUST Menu icon  
Move a red frame pointer to AUTO PC  
Adj. icon and press SELECT button.  
Store adjustment parameters.  
Adjustment parameters from Auto PC Adjustment can be memorized  
in this projector. Once parameters are memorized, setting can be  
done just by selecting Mode in PC SYSTEM Menu (P22). Refer to  
step 3 of MANUAL PC ADJUSTMENT section (P26).  
NOTE  
Fine sync, Total dots and Picture Position of some computers can  
not be fully adjusted with this Auto PC Adjustment function. When  
the image is not provided properly through this function, manual  
adjustments are required. (Refer to page 25, 26.)  
Auto PC Adjustment function cannot be operated when RGB,”  
720p (HDTV),” “1035i (HDTV)or 1080i (HDTV)is selected on PC  
SYSTEM Menu (P22).  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
MANUAL PC ADJUSTMENT  
This projector can automatically tune to the display signals from most personal computers currently distributed. However,  
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-  
Scan system of this projector. If this happens, projector cannot reproduce a proper image and the image may be recognized  
as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.  
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special  
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This  
enables you to recall the setting for a specific computer whenever you use it.  
Note : This PC ADJUST Menu cannot be operated when "RGB" is selected on PC SYSTEM Menu (P22).  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to PC  
ADJUST Menu icon.  
PC ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust and then press SELECT button.  
Adjustment dialog box will appear. Press POINT LEFT/RIGHT  
button to adjust value.  
PC ADJUST Menu icon  
Move a red frame icon to the item and  
press SELECT button.  
Fine sync  
Adjusts an image as necessary to eliminate flicker from the display.  
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)  
Shows status  
(Stored / Free) of the  
selected Mode.  
Total dots  
Selected Mode  
The number of total dots in one horizontal period. Press POINT  
LEFT/RIGHT button(s) and adjust number to match your PC image.  
Horizontal  
Adjusts horizontal picture position. Press POINT LEFT/RIGHT  
button(s) to adjust the position.  
Press POINT LEFT/RIGHT  
button to adjust the value.  
Vertical  
Adjusts vertical picture position. Press POINT LEFT/RIGHT  
button(s) to adjust the position.  
Press SELECT button at this  
icon to adjust Clamp,” “Display  
area (H/V)or set Full screen.”  
Current mode  
Press SELECT button to show the information of computer selected.  
Clamp  
Adjusts clamp level. When the image has a dark bar(s), try this  
adjustment.  
Current mode  
Press SELECT button at  
Current mode icon to show  
the information of computer  
connected.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
Display area  
Selects area displayed with this projector. Select the resolution at  
Display area dialog box.  
Press SELECT button at  
Display area icon and Display  
area dialog box appears.  
Display area H  
Adjustment of horizontal area displayed with this projector. Press  
POINT LEFT/RIGHT button(s) to decrease/increase value to match  
the resolution of image.  
Display area  
Display area V  
Adjustment of vertical area displayed with this projector. Press  
POINT LEFT/RIGHT button(s) to decrease/increase value to match  
the resolution of image.  
Full screen  
Press POINT LEFT/RIGHT button(s) to switch Full screen function to  
Onor Off.Set Onto resize the image with 4 x 3 aspect ratio to  
fit the screen.  
NOTE : Fine sync, Total dots, Display area (H/V) and Full screen  
cannot be adjusted when 1035i (HDTV)or 1080i (HDTV)”  
is selected on PC SYSTEM Menu (P22).  
To store adjustment data.  
This Mode has parameters being stored.  
Store  
3
To store adjustment parameters, move a red frame pointer to  
Store icon and then press SELECT button. Move a red arrow  
pointer to any of Mode 1 to 5 that you want to store to and then  
press SELECT button.  
Mode free  
To clear adjustment parameters previously set, move a red  
frame pointer to Mode free icon and then SELECT button. Move  
a red arrow pointer to the Mode that you want to clear and then  
press SELECT button.  
Vacant Mode  
Shows values of Total dots,”  
Horizontal,” “Vertical,” “Display  
area H,and Display area V.”  
Other icons operates as follows.  
Reset  
Reset all adjust parameters on adjustment dialog box to previous  
figure.  
To clear adjustment data.  
Quit  
Closes PC ADJUST MENU.  
Close this dialog box.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT (DIRECT)  
Select image level among Standard, Real, Image 1, Image 2, Image 3  
IMAGE button  
and Image 4 by pressing IMAGE button on Top Control or on Remote  
Control Unit.  
Standard  
Real  
Standard  
Normal picture adjustment preset on this projector.  
Image 1  
Image 2  
Image 3  
Image 4  
Real  
Picture adjustment improved in reproduction of halftones. This  
adjustment is suitable for providing better image in brighter place.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P28, 29).  
IMAGE LEVEL SELECT (MENU)  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
level that you want to set and then press SELECT button.  
IMAGE SELECT  
Menu icon  
Standard  
Normal picture adjustment preset on this projector.  
Move a red frame pointer to the level  
and press SELECT button.  
Real  
Picture adjustment improved in reproduction of halftones. This  
adjustment is suitable for providing better image in brighter place.  
The level being selected.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P28, 29).  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
IMAGE LEVEL ADJUSTMENT  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to  
IMAGE ADJUST Menu icon.  
IMAGE ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust. and then press SELECT button.  
The level of each item is displayed. Adjust each level by  
pressing POINT LEFT/RIGHT button(s).  
IMAGE ADJUST  
Menu icon  
Move a red frame pointer to  
the item to be selected and  
then press SELECT button.  
Contrast  
Press POINT LEFT button to decrease contrast, and POINT RIGHT  
button to increase contrast. (From 0 to 63.)  
Brightness  
Press POINT LEFT button to adjust image darker, and POINT  
RIGHT button to adjust brighter. (From 0 to 63.)  
Selected Image level  
Color  
Press POINT LEFT button to lighten color, and POINT RIGHT button  
to deeper color. (From 0 to 63.)  
Tint  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Press POINT LEFT button or POINT RIGHT button to obtain proper  
color. (From 0 to 63.)  
Store icon  
Press SELECT button at this icon to  
store the adjustment.  
White balance (Red)  
Press POINT LEFT button to lighten red tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
White balance (Green)  
Press POINT LEFT button to lighten green tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
White balance (Blue)  
Press POINT LEFT button to lighten blue tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Sharpness  
Press POINT LEFT button to soften the image, and POINT RIGHT  
button to sharpen the image. (From 0 to 15.)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Gamma  
Press either POINT LEFT button or POINT RIGHT button to obtain  
better balance of contrast. (From 0 to 15.)  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
Store  
3
To store manually preset image, move a red frame pointer to  
Store icon and press SELECT button. Image Level Menu will  
appear. Move a red frame pointer to the Image 1 to 4 where you  
want to set and then press SELECT button.  
Image Level Menu  
Move a red frame pointer to any  
of Image 1 to 4 where you want  
to set and then press SELECT  
button.  
Other icons operate as follows.  
Reset  
Reset all adjustment to previous figure.  
Quit  
Closes IMAGE MENU.  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
SCREEN Menu icon.  
SCREEN MENU  
1
2
Press POINT DOWN button and move a red frame pointer to the  
function that you want to select and then press SELECT button.  
SCREEN Menu icon  
Move the red frame to the function and  
press SELECT button.  
Normal  
Provides image to fit screen size.  
True  
Provides image in its original size. When the original image size is  
larger than screen size (800 x 600), this projector enters Digital  
zoom +mode automatically.  
NOTE  
This SCREEN Menu cannot be operated when  
1035i (HDTV)or 1080i (HDTV)is selected on  
PC SYSTEM Menu (P22).  
Wide  
Wide cannot be selected when 720p (HDTV)is  
Provides image to fit wide video aspect ratio (16 : 9) by expanding  
image width uniformly. This function can be used for providing a  
squeezed video signal at 16 : 9.  
selected on PC SYSTEM Menu (P22).  
True and Digital zoom +/cannot be selected  
when RGBis selected on PC SYSTEM Menu  
(P22).  
Digital zoom +  
This projector cannot display any resolution higher  
than 1280 X 1024. If your computers screen  
resolution is higher than 1280 X 1024, reset the  
resolution to the lower before connecting projector.  
When Digital zoom + is selected, ON-SCREEN MENU disappears  
and the message D. Zoom +is displayed. Press SELECT button to  
expand image size. And press POINT UP/DOWN/LEFT/RIGHT  
button(s) to pan the image. Panning function can work only when  
the image is larger than screen size.  
Digital zoom cannot be fully operated when the  
image resolution is higher than SVGA (800 x 600).  
A projected image can be also expanded by pressing D.ZOOM ●  
button on Remote Control Unit.  
The image data in other than SVGA (800 x 600) is  
modified to fit the screen size in initial mode.  
Digital zoom –  
Panning function may not operate properly if the  
computer system prepared on PC ADJUST Menu  
is used.  
When Digital zoom is selected, ON-SCREEN MENU disappears  
and the message D. Zoom –” is displayed. Press SELECT button to  
compress image size.  
A projected image can be also compressed by pressing D.ZOOM ●  
button on Remote Control Unit.  
To cancel Digital Zoom +/mode, press any button except D.ZOOM  
/, SELECT, and POINT buttons.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING INPUT SOURCE  
INPUT button  
Video  
DIRECT OPERATION  
Choose Video by pressing INPUT button on Top Control or on Remote  
Control Unit.  
Computer  
If projector cannot reproduce proper video source, select correct input  
source through MENU OPERATION (see below).  
MENU OPERATION  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
INPUT Menu icon.  
INPUT MENU  
1
Press POINT DOWN button to move a red arrow pointer to  
Video and then press SELECT button. Source Select Menu will  
appear.  
2
Move a pointer to Video and  
press SELECT button.  
Move a pointer to the source that you want to select and then  
press SELECT button.  
3
VIDEO  
Projector automatically detects incoming Video signal,  
and adjusts itself to optimize its performance.  
Auto  
When both VIDEO jack and S-VIDEO jack are  
connected, S-VIDEO jack has priority over VIDEO jack.  
When both Y-Pb/Cb-Pr/Cr jacks and S-VIDEO jack are  
connected, Y-Pb/Cb-Pr/Cr jacks have priority over S-  
VIDEO jack.  
Source Select Menu (VIDEO)  
Move a pointer to the source and press SELECT button.  
When video input signal is connected to VIDEO jack,  
select Video.  
Video  
When video input signal is connected to S-VIDEO jack,  
select S-Video.  
S-Video  
When video input signal is connected to Y-Pb/Cb-  
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.  
Y,Pb/Cb,Pr/Cr  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING VIDEO SYSTEM  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to AV  
SYSTEM Menu icon.  
1
2
Press POINT DOWN button to move a red arrow pointer to the  
system that you want to select and then press SELECT button.  
VIDEO JACK OR S-VIDEO JACK  
AV SYSTEM MENU (VIDEO OR S-VIDEO)  
Auto  
Projector automatically detects incoming Video system, and adjusts  
itself to optimize its performance.  
When Video System is PAL-M or PAL-N, select system manually.  
AV SYSTEM Menu icon  
This box indicates the system  
being selected.  
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N  
If projector cannot reproduce proper video image, it is necessary to  
select a specific broadcast signal format among PAL, SECAM, NTSC,  
NTSC 4.43, PAL-M, and PAL-N.  
Move the pointer to the  
system and press  
SELECT button.  
Y, Pb/Cb, Pr/Cr JACKS  
AV SYSTEM MENU (COMPONENT VIDEO)  
Auto  
Projector automatically detects incoming Video signal, and adjusts  
itself to optimize its performance.  
COMPONENT VIDEO SIGNAL FORMAT  
AV SYSTEM Menu icon  
This box indicates the system  
being selected.  
If projector cannot reproduce proper video image, it is necessary to  
select a specific component video signal format among 480i, 575i,  
480p, 575p, 720p, 1035i and 1080i.  
Move the pointer to the  
system and press  
SELECT button.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT (DIRECT)  
Select image level among Standard, Cinema, Image 1, Image 2,  
Image 3 and Image 4 by pressing IMAGE button on Top Control or on  
Remote Control Unit.  
IMAGE button  
Standard  
Cinema  
Image 1  
Image 2  
Image 3  
Image 4  
Standard  
Normal picture adjustment preset on this projector.  
Cinema  
Picture level adjusted for the picture with fine tone.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P33,34).  
IMAGE LEVEL SELECT (MENU)  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
level that you want to set and then press SELECT button.  
IMAGE SELECT  
Menu icon  
Standard  
Normal picture adjustment preset on this projector.  
Move the red frame pointer to the  
level and press SELECT button.  
Cinema  
Picture level adjusted for the picture with fine tone.  
IMAGE 1~4  
The level being selected.  
User preset picture adjustment in IMAGE ADJUST Menu (P33,34).  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
IMAGE LEVEL ADJUSTMENT  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
IMAGE ADJUST Menu icon.  
IMAGE ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust and then press SELECT button.  
The level of each item is displayed. Adjust each level by  
pressing POINT LEFT/RIGHT button(s).  
IMAGE ADJUST  
Menu icon  
Move a red frame pointer to  
the item to be selected and  
then press SELECT button.  
Contrast  
Press POINT LEFT button to decrease contrast, and POINT RIGHT  
button to increase contrast. (From 0 to 63.)  
Brightness  
Press POINT LEFT button to adjust image darker, and POINT  
RIGHT button to adjust brighter. (From 0 to 63.)  
Color  
Press POINT LEFT button to lighten color, and POINT RIGHT button  
to deeper color. (From 0 to 63.)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Tint  
Press POINT LEFT button or POINT RIGHT button to obtain proper  
color. (From 0 to 63.)  
Press SELECT button at this icon to  
display other items.  
White balance (Red)  
Press POINT LEFT button to lighten red tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Press SELECT button at this icon to  
display previous items.  
White balance (Green)  
Press POINT LEFT button to lighten green tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
White balance (Blue)  
Press POINT LEFT button to lighten blue tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Sharpness  
Press POINT LEFT button to soften the image, and POINT RIGHT  
button to sharpen the image. (From 0 to 15.)  
Press SELECT button at this icon to  
store the value.  
Gamma  
Press either POINT LEFT button or POINT RIGHT button to obtain  
better balance of contrast. (From 0 to 15.)  
NOTE : Tint cannot be adjusted when the video system is PAL,  
SECAM, PAL-M or PAL-N.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
Store  
3
To store the adjustment data, move a red frame pointer to Store  
icon and press SELECT button. Image Level Menu will appear.  
Move a red frame pointer to the Image Level 1 to 4 and then  
press SELECT button.  
Other icons operate as follows.  
Image Level Menu  
Move a red frame pointer to  
the image icon to be set  
and then press SELECT  
button.  
Reset  
Reset all adjustment to previous figure.  
Quit  
Closes IMAGE MENU.  
Store icon  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
SCREEN Menu icon.  
SCREEN MENU  
1
2
Press POINT DOWN button and move a red frame pointer to the  
function that you want to select and then press SELECT button.  
SCREEN Menu icon  
Move the red frame to the function and  
press SELECT button.  
Normal  
Provides image at a normal video aspect ratio of 4 : 3.  
NOTE : SCREEN Menu cannot be operated when  
720p,” “1035i,or 1080iis selected on AV  
SYSTEM Menu (P31).  
Wide  
Provides image at a wide screen ratio of 16 : 9.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
SETTING MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red-frame pointer to  
SETTING icon.  
SETTING MENU  
1
2
Press POINT DOWN button to move a red-frame pointer to the  
Set a red frame  
SETTING Menu icon  
item that you want to set and then press  
SELECT button.  
pointer to the item  
and press SELECT  
button.  
Setting dialog box appears.  
Language  
Language used in ON-SCREEN MENU is selectable from among  
English, German, French, Italian, Spanish, Portuguese, Dutch,  
Swedish, Chinese, Korean and Japanese.  
Keystone  
When the image is distorted vertically, select Keystone. ON-  
SCREEN MENU disappears and Keystone dialog box is displayed.  
Correct keystone distortion by pressing POINT UP/DOWN button(s).  
Refer to KEYSTONE ADJUSTMENT on page 20.  
When pressing SELECT  
button at Language,  
Blue back  
Language Menu appears.  
When this function is On,this projector will produce a blue image  
instead of the video noise on the screen when any input source is  
unplugged or turned off.  
Display  
This function decides whether to display On-Screen Displays.  
On ··· shows all the On-Screen Displays.  
Off ···· sets On-Screen Displays disappeared except;  
ON-SCREEN MENU  
Power off?message (P19)  
P-TIMER  
No signalmessage (P36)  
Move a pointer to the item  
and then press POINT  
LEFT/RIGHT button(s).  
Logo  
When this function is On,projector displays our logo when starting  
up.  
Ceiling function  
Ceiling  
When this function is On,picture is top / bottom and left / right  
reversed. This function is used to project the image from a ceiling  
mounted projector.  
Rear  
Rear function  
When this function is On,picture is left / right reversed. This  
function is used to project the image to a rear projection screen.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
Power management  
This function turns Projection Lamp off when this projector detects  
signal interruption and is not used for a certain period in order to  
reduce power consumption and maintain the Lamp-life. (This  
projector is shipped with this function ON.)  
Time left until Lamp off.  
Power Management function operates to turn Projection Lamp off  
when the input signal is interrupted and any button is not pressed  
over 5 minutes. This function operates as follows;  
1. When any input signal is interrupted, No signaland the  
counting down display appears (for 5 minutes).  
2. When Projection Lamp is turned off, READY Indicator is turned  
off. Cooling Fans operate and Projection Lamp is turned off for  
90 seconds. (During this "Cooling Down" period, projector  
cannot be turned on.)  
3. When Projection Lamp has cooled down, READY Indicator  
flashes and Projection Lamp can be turned on again (Power  
Management mode).  
In this Power Management mode, Projection Lamp is  
automatically turned on when the input signal is connected or  
projector is operated with any button on Top Control or on  
Remote Control Unit again.  
Remote control  
This projector has two different remote control codes; the factory-set  
normal code (Code 1) and the secondary code (Code 2). This  
switching function prevents remote control operation mixture (jam)  
when operating several projectors or video equipment together.  
When operating projector in Code 2,both projector and Remote  
Control Unit must be switched to Code 2.”  
To change the code of Projector;  
Set Remote control in the SETTING MENU to Code 2.”  
To change the code of the Remote Control Unit;  
Press both MENU and IMAGE buttons on Remote Control Unit  
simultaneously for over 10 seconds.  
After changing the code, make sure Remote Control operates  
properly.  
To return to the normal code (Code 1), operate both projector and  
Remote Control in the ways above again.  
Move the pointer to Lamp counter reset and then press  
SELECT button. The message Lamp replace counter  
reset?is displayed.  
NOTE : When battery of Remote Control Unit is replaced, the remote  
control code automatically returns to the normal code (Code  
1).  
Lamp counter reset  
This function is used to reset Lamp Replace Counter. When  
replacing Projection Lamp, reset Lamp Replace Counter by using  
this function. Refer to page 38 for operation.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
MAINTENANCE  
WARNING TEMP. INDICATOR  
WARNING TEMP. Indicator flashes red when an internal temperature of a projector exceeds the normal temperature. This  
Indicator stops flashing when the temperature of a projector returns to normal.  
When WARNING TEMP. Indicator continues to flash, check the items listed below.  
Ventilation Slots of the projector may be blocked. In such an event, reposition the projector so that Ventilation Slots  
are not obstructed.  
1
Air Filters may be clogged with dust particles. Clean Air Filters by following the section AIR FILTER CARE AND  
CLEANING below.  
2
If WARNING TEMP. Indicator remains on after performing the above checks, Cooling Fans or the Internal Circuits may  
be malfunctioning. Contact service personnel from an authorized dealer or a service station.  
3
AIR FILTER CARE AND CLEANING  
Removable Air Filters prevent dust from accumulating on the surface of Projection Lens and Projection Mirror. Should Air  
Filters become clogged with dust particles, it will reduce Cooling Fanseffectiveness and may result in internal heat build up  
and adversely affect the life of the projector. Clean Air Filters following the steps below:  
Turn off the projector, and disconnect AC power cord from the  
AC outlet.  
AIR FILTER (Small)  
1
Turn the projector upside down and remove two Air Filters  
(Large and Small) by pulling the latches upward.  
2
Clean Air Filters with a brush or wash out dust and particles.  
3
4
Replace each Air Filter properly. Make sure that Air Filters are  
fully inserted.  
CAUTION  
Do not operate the projector with Air Filter removed. Dust  
may accumulate on LCD Panel and Projection Mirror  
degrading picture quality.  
Do not put small parts into Air Intake Vents. It may result in  
malfunction of the projector.  
AIR FILTER (Large)  
RECOMMENDATION  
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments  
may cause poor image quality.  
When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements  
inside the projector. This condition may degrade the quality of a projected image.  
When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.  
CLEANING PROJECTION LENS  
Follow these steps to clean Projection Lens:  
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.  
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.  
1
Lightly wipe lens surface with a cleaning cloth.  
2
3
When the projector is not in use, replace Lens Cap.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
LAMP REPLACEMENT  
When the life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When a  
projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required.  
CAUTION  
CAUTION  
For continued safety, replace with a lamp  
assembly of the same type.  
Allow a projector to cool for at least 45  
minutes before you open Lamp Cover. The  
inside of a projector can become very hot.  
Do not drop a lamp assembly or touch a glass  
bulb! The glass can shatter and may cause  
injury.  
Follow these steps to replace the lamp assembly.  
Turn off the projector and disconnect AC plug. Allow the  
projector to cool for at least 45 minutes.  
LAMP COVER  
1
Remove a screw with a screwdriver to remove Lamp Cover.  
2
3
Remove 2 screws with a screwdriver and pull out Lamp  
Assembly by grasping Handle.  
Replace Lamp Assembly with a new one and tighten 2 screws  
back. Make sure that Lamp Assembly is set properly. Replace  
Lamp Cover and tighten a screw.  
4
HANDLE  
Connect AC Power Cord to the projector and turn it on.  
5
6
LAMP  
ASSEMBLY  
Reset Lamp Replace Counter (refer to the section Lamp  
Replace Counterbelow).  
NOTE : Do not reset Lamp Replace Counter when Projection  
Lamp is not replaced.  
ORDER REPLACEMENT LAMP  
Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give the following  
information to the dealer.  
Model No. of your projector : LC-SM3  
Replacement Lamp Type No. : POA-LMP36  
(Service Parts No. 610 293 8210)  
LAMP REPLACE COUNTER  
Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP  
REPLACE Indicator stops lighting.  
Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to  
move a red frame pointer to SETTING Menu icon (refer to page 35, 36).  
1
Press POINT DOWN button to move a red frame pointer to Lamp counter resetand then press  
message "Lamp replace counter reset?" is displayed. Move the pointer to [Yes] and then press SELECT button.  
SELECT button. The  
2
Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.  
3
Do not reset Lamp Replace Counter except after Projection Lamp is replaced.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TROUBLESHOOTING  
Before calling your dealer or service center for assistance, check the items below once again.  
1. Make sure you have connected a projector to your computer or video equipment as described in the section  
"CONNECTING THE PROJECTOR" on pages 11 ~ 13.  
2. Check cable connection. Verify that all computer, video and power cord are properly connected.  
3. Verify that all power is switched on.  
4. If a projector still does not produce an image, re-start your computer.  
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display. The  
problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, be sure  
to turn the computer and monitor off before you power up the projector. Turn the projector on, and then the computer.)  
6. If the problem still exists, check following chart.  
Problem:  
No power.  
Try these Solutions  
Plug a projector into your AC outlet.  
Make sure READY Indicator lights.  
Wait 90 seconds after a projector is turned OFF when turning the projector back on.  
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as  
follows:  
1. LAMP indicator lights bright and READY indicator turns off.  
2. After 90 seconds, READY indicator lights green again and a projector may be  
turned on by pressing Power ON-OFF button.  
Check WARNING TEMP. indicator. If the indicator flashes red, the projector cannot be  
turned on.  
(See "TURNING ON/OFF PROJECTOR" section on page 19.)  
Check Projection Lamp. (Refer to page 38.)  
Make focus adjustment.  
Make sure a projection screen is at least 5.3(1.6m) from the projector.  
See if cleaning Projection Lens is needed.  
Image is out of  
focus.  
NOTE : Moving a projector from a cool temperature location to a warm temperature location  
may result in moisture condensation in Projection Lens. In such an event, leave a  
projector OFF and wait until condensation disappears.  
Check Ceiling / Rear feature. (See SETTINGsection on page 35.)  
Picture is Left/Right  
reversed.  
Check Ceiling feature. (See SETTINGsection on page 35.)  
Picture is  
Top/Bottom  
reversed.  
Check Display feature.(See SETTINGsection on page 35.)  
Some displays are  
not seen during the  
Operation.  
Check the connection between your computer or video equipment and a projector.  
Check NO SHOW function. (Refer to page 21.)  
When turning a projector on, it takes about 30 seconds to display an image.  
Check the system that you select is corresponding with your computer or video  
equipment.  
No image.  
No sound.  
Make sure the temperature is out of the Operating Temperature (5°C ~ 35°C).  
Check audio cable connection from audio input source.  
Check the audio source.  
Press VOLUME (+) button.  
Press MUTE button.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
Problem:  
Remote Control Unit  
does not work.  
Try these Solution  
Check the battery.  
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.  
Make sure of maximum operating distance 16.4(5m) between the receiver on the  
projector and Remote Control Unit.  
Make sure the code of Remote Control is set to conform to projector.  
(See SETTINGsection on page 35, 36.)  
WARNING :  
High voltages are used to operate this projector. Do not attempt to open the cabinet.  
after following all operating instructions,  
If the problem still persists  
projector or the service center.  
obtain service.  
contact the sales dealer where you purchased the  
Give the model number and explain the problem in detail. We will advise you of how to  
This symbol on the nameplate means the product is Listed by Underwriters  
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards  
against risk of fire, casualty and electrical hazards.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TECHNICAL SPECIFICATIONS  
Multi-media Projector  
Projector Type  
10.12" x 2.98" x 9.06" (257mm x 75.8mm x 230mm) (not including Adjustable Feet and Lens)  
6.17lbs (2.8 kg)  
(W x H x D)  
Dimensions  
Net Weight  
0.7" TFT Active Matrix type, 3 panels  
800 x 600 dots  
LCD Panel System  
Panel Resolution  
Number of Pixels  
Color System  
1,440,000 (800 x600 x 3 panels)  
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N  
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i  
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz  
Adjustable from 34to 200”  
High Definition TV Signal  
Scanning Frequency  
(Diagonal)  
Projection Image size  
Horizontal Resolution  
Projection Lens  
500 TV lines (S-Video)  
F 1.6 ~ 1.78 lens with f 28.7 mm ~ 34.5 mm with manual zoom and focus  
5.3~ 26.6(1.6 m ~ 8.1 m)  
Throw Distance  
150 W  
Projection Lamp  
RCA Type x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)  
Mini Jack (stereo) x 1  
Video Input Jacks  
Audio Input Jacks  
Computer Input Terminals  
Computer Audio Input Jack  
Control Port Connector  
USB Connector  
(VGA) HDB 15 Terminal x 1  
Mini Jack (stereo) x 1  
Mini DIN 8 pin x 1  
USB Series B receptacle x 1  
Mini Jack (stereo) x 1  
Audio Output Jacks  
Internal Audio Amp  
Built-in Speaker  
1.0 W RMS  
1 speaker, ø1.1" (28mm)  
0˚ to 10.6˚  
Feet Adjustment  
Voltage and  
AC 100 ~ 120 V (2.8 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)  
AC 200 ~ 240 V (1.4 A Max. Ampere), 50 / 60 Hz (Except U.S.A. and CANADA)  
Power Consumption  
Operating Temperature  
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)  
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)  
Storage Temperature  
Power Source  
Operating Range  
Dimensions  
:
:
:
:
Lithium Type (CR2025 / 3.0V)  
16.4(5m) / ±30˚  
2.1x 0.28x 5.3(54mm x 7mm x 135mm)  
1.27oz (36 g) (including battery)  
Remote Control Transmitter  
Net Weight  
Owners Manual  
Accessories  
AC Power Cord  
Wireless Remote Control Transmitter and Battery  
VGA Cable  
Carrying Bag  
Lens Cap  
The specifications are subject to change without notice.  
OPTIONAL PARTS  
The parts listed below are optionally supplied. When ordering those parts, give description and Type No. of it to the sales  
dealer.  
Wireless Remote Control Unit Type No. : RC-XM2  
Control Cable for ADB Port  
MAC Adapter  
Type No.: POA-MCMAC  
Type No.: POA-MACAP  
Control Cable for PS/2Port  
Control Cable for Serial Port  
Type No. : POA-MCPS2  
Type No.: POA-MCSRL  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
CONFIGURATIONS OF THE TERMINALS  
COMPUTER INPUT TERMINAL (ANALOG)  
Terminal : HDB15-PIN  
Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied). When connecting the  
Macintosh computer, MAC Adapter (not supplied) is required.  
1
2
3
4
5
6
7
8
Red Input  
Green Input  
Blue Input  
Sense 2  
9
No Connect  
Pin Configuration  
10 Ground (Vert.sync.)  
11 Sense 0  
2
1
5
4
3
12 Sense 1  
10  
9
8
7
6
15  
14  
13  
12  
11  
Ground (Horiz.sync.) 13 Horiz. sync.  
Ground (Red)  
Ground (Green)  
Ground (Blue)  
14 Vert. sync.  
15 Reserved  
CONTROL PORT CONNECTOR  
Terminal : Mini DIN 8-PIN  
Connect control port (PS/2, Serial or ADB port) on your computer to this connector with Control Cable (not supplied).  
PS/2  
-----  
Serial  
R X D  
-----  
ADB  
-----  
Pin Configuration  
1
2
3
4
5
6
7
8
CLK  
DATA  
GND  
-----  
ADB  
-----  
-----  
8
7
6
GND  
GND  
-----  
5
4
3
RTS / CTS  
T X D  
GND  
2
1
-----  
-----  
GND  
-----  
-----  
GND  
GND  
USB CONNECTOR (Series B)  
Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).  
Pin Configuration  
1
2
3
4
Vcc  
- Data  
+ Data  
Ground  
2
3
1
4
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A-key to better communications  
Canada  
U.S.A.  
EIKI International, Inc.  
EIKI CANADA - Eiki International, Inc.  
P.O. Box 156, 310 First St. - Unit 2,  
Midland, ON, L4R 4K8, Canada  
Tel : 800-563-3454 (705-527-4084)  
Fax : 800-567-4069 (705-527-4087)  
E-Mail : [email protected]  
26794 Vista Terrace Drive  
Lake Forest, CA, USA 92630-8113  
Tel : 800-242-3454 (949-457-0200)  
Fax : 800-457-3454 (949-457-7878)  
E-Mail : [email protected]  
Eastern Europe  
EIKIˆ CZECH spol. s.r.o.  
Umelecká 15  
170 00 Praha 7  
Czech Republic  
Tel : +42 02 20570024  
+42 02 20571413  
Fax : +42 02 20571411  
E-Mail : [email protected]  
Deutschland & Österreich  
EIKI Deutschland GmbH  
Am Frauwald 12  
65510 Idstein  
Deutschland  
Tel : 06126-9371-0  
Fax : 06126-9371-11  
E-Mail : [email protected]  
Japan & Worldwide  
EIKI Industrial Company Limited.  
4-12 Banzai-Cho, Kita-Ku, Osaka,  
530-0028 Japan  
Tel : +81-6-6311-9479  
Fax : +81-6-6311-8486  
E-Mail : [email protected]  
WorldWide Website http://www.eiki.com  
Printed in Japan  
Part No. 610 296 2024 (1AA6P1P2997-- MZ6B)  
© 2001 Eiki International, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Extron electronic Scale DSC 301 HD User Manual
Extron electronic Stereo Amplifier RGB 580XI User Manual
Fujitsu Scanner iX500 User Manual
Fundex Games Board Games Squeezed Out User Manual
Gaggia Coffeemaker Syncrony User Manual
Gefen Cable Box EXT DVI 141B User Manual
GE Microwave Oven 164D2966P127 I User Manual
GE Washer EWA4600 User Manual
Gitzo Camcorder Accessories GT1541T User Manual
Global Machinery Company Lathe ML10001 User Manual