Fisher Price Crib K2566 User Manual

K2566  
WARNING  
IMPORTANT! KEEP INSTRUCTIONS  
FOR FUTURE REFERENCE.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
IMPORTANT! Please remove all parts from the package and identify them before assembly.  
Some parts may be packed in the pad.  
Seat Back Tube  
Toy Bar  
2 Retainers  
Pad  
Footrest with Soothing Unit  
Base Tube  
2 Feet  
Left Base Wire  
Right Base Wire  
#8 x 1,9 cm Screw – 2  
M5 x 20 mm Screw - 2  
Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Battery Installation  
Assembly  
IMPORTANT! Before assembly and each use, inspect this product  
for damaged hardware, loose joints, missing parts or sharp edges.  
DO NOT use if any parts are missing or broken. Contact Mattel for  
replacement parts and instructions if needed. Never substitute parts.  
Hint: We recommend using alkaline batteries for  
longer battery life.  
Base Tube  
1,5V x 4  
“D” (LR20)  
Left Base Wire  
1
Right Base Wire  
• Place the base tube on a flat surface.  
• Position the left and right base wires as shown.  
• Fit the left base wire and right base wire into the base tube.  
• Loosen the screws in the soothing unit battery  
compartment door. Remove the battery compartment door.  
• Insert fourD(LR20) alkaline batteries.  
Replace the battery compartment door.Tighten the screws.  
• Protect the environment by not disposing of this  
product with household waste (2002/96/EC).  
Check your local authority for recycling advice  
and facilities (Europe only).  
Battery Safety Information  
In exceptional circumstances, batteries may leak fluids that  
can cause a chemical burn injury or ruin your product. To  
avoid battery leakage:  
Feet Holes  
• Do not mix old and new batteries or batteries of different  
types: alkaline, standard (carbon-zinc) or rechargeable  
(nickel-cadmium).  
2
• Insert batteries as indicated inside the battery compartment.  
• Position the feet so the holes are toward you and the  
non-skid surface is down.  
• Fit the feet on the base tube, as shown.  
• Remove batteries during long periods of non-use.Always  
remove exhausted batteries from the product. Dispose of  
batteries safely. Do not dispose of this product in a fire.  
The batteries inside may explode or leak.  
• Never short-circuit the battery terminals.  
• Use only batteries of the same or equivalent type,  
as recommended.  
• Do not charge non-rechargeable batteries.  
• Remove rechargeable batteries from the product  
before charging.  
• If removable, rechargeable batteries are used, they are  
only to be charged under adult supervision.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Retainers  
Seat Back Tube  
Base Wire  
Base Wire  
3
• Insert an M5 x 20 mm screw through each foot and tighten.  
Flex Base Wires Inward  
Pull Up  
Tabs  
5
• Position the seat back  
tube above the base  
assembly.  
• Fit the seat back tube  
completely onto the  
base wires.  
• Fit a retainer (rounded  
side inward) to one  
4
end of the seat back tube.  
• Insert a #8 x 1,9 cm screw through the outside hole in  
• While flexing the base wires toward each other, hook the  
footrest onto the ends of the base wires.  
the seat back tube and into the retainer.  
• Push the footrest down completely to the tabs on the base  
wires.  
• While holding the retainer in place, tighten the screw.  
• Repeat this procedure to secure the other side of the  
seat back tube to the base assembly using the remaining  
retainer and #8 x 1,9 cm screw.  
• Pull up on the seat back tube to be sure it is secure. If you  
can remove either end of the seat back tube, you have not  
assembled it correctly. Remove the screws and retainers.  
Re-read and repeat Assembly step 5.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Latch  
Tab  
6
7
• Fit the pad upper pocket onto the seat back tube.  
• Fit the pad lower pocket onto the footrest.  
• Fit the toy bar ends into the sockets in the footrest.  
Hint: The square end of the toy bar fits into the square  
socket and the circular end of the toy bar fits into the  
circular socket.  
• Make sure the toy bar latches are secure.The small tabs on  
the sockets should be visible in the opening in the latches.  
Assembly is now complete.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and Use  
TIGHTEN  
Buckle  
Free End  
WARNING  
To prevent serious injury or death:  
Fall Hazard – It is dangerous to use  
this reclined cradle on an elevated  
surface, since child’s movement may  
cause product to slide or tip over. Use  
only on a floor.  
Suffocation Hazard – Never use on  
a soft surface (bed, sofa, cushion),  
since product can tip over and cause  
suffocation in soft surfaces.  
Anchored End  
LOOSEN  
Buckle  
Free End  
• Always use the restraint system.  
• Never leave child unattended.  
• Never use as a car seat.  
• Never use as a carrier or lift while  
child is seated. Never use the toy bar  
as a handle.  
• Not recommended for children who  
can sit up by themselves (6 months  
approximately, until 9 kg/ 20 lbs).  
2
Anchored End  
To tighten the belts:  
Feed the anchored end of the belt up through the buckle  
to form a loop  
• Pull the free end of the belt  
• Repeat this procedure to tighten the other belt.  
.
A
B
.
To loosen the belts:  
• Feed the free end of the belt up through the buckle to  
form a loop A . Enlarge the loop by pulling on the end of  
the loop toward the buckle.  
• Pull the anchored end of the belt to shorten the free end  
B
of the belt  
.
• Repeat this procedure to loosen the other belt.  
Note: After adjusting the belts to fit your child, make sure you  
pull on them to be sure they are securely fastened.  
Restraint Pad  
1
Buckle  
Restraint Belt  
3
Securing your Child  
Calming Vibrations  
• Make sure your child is properly secured in the seat.  
• To turn vibrations on, slide the power switch on the  
• If the toy bar is attached, remove it before placing your  
child in the seat. Place your child in the seat. Position the  
restraint pad between your child’s legs.  
soothing unit to the on position  
• To turn vibrations off, slide the power switch on the  
soothing unit to the off position  
.
• Fasten both restraint belts to the buckles on each side  
of the restraint pad. Make sure you hear a “click” on both  
sides.  
.
• Check to be sure the restraint is securely attached by  
pulling it away from your child.The restraint should  
remain attached.  
IMPORTANT! If vibrations become faint, or if there are no  
vibrations, remove theD(LR20) batteries from the soothing  
unit and dispose of them properly. Replace the batteries with  
four, newD(LR20) alkaline batteries.  
• Attach the toy bar, if desired (see Assembly step 7).  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and Use  
Latch  
5
Remove the Toy Bar  
• Pull the ends of the latches and lift the toy bar.  
Care  
The pad is machine washable.Wash the pad separately in  
cold water on the gentle cycle. Do not use bleach.Tumble  
dry separately on low heat and remove promptly.The frame,  
toy bar can be wiped clean using a mild cleaning solution and  
damp cloth. Do not use bleach. Do not immerse the soothing  
unit or toy bar.  
4
Mode Switch  
Rainforest Sounds  
or Music Switch  
Volume Button  
Rainforest Sounds or Music  
• Slide the switch to rainforest sounds or music  
.
Child-activated (Short Play)  
• Slide the mode switch to  
for child activated mode.  
• When baby bats the monkey or the toucan, baby is  
rewarded with rainforest sounds or music along with  
motion and lights.  
Parent-activated (Long Play)  
Slide the mode switch to  
for parent activated mode.  
Baby enjoys 10 minutes of rainforest sounds or music,  
a light show and motion.  
Off  
• Slide the mode switch to to turn off sounds, lights,  
and motion.  
Volume  
• Push the volume button once for low volume  
press again for high volume ; press again for off  
;
.
IMPORTANT! If lights dim or sound or movement become  
faint or stop all together, remove the "D" (LR20) batteries  
from the soothing unit and dispose of them properly.  
Replace the batteries with four, new "D" (LR20)  
alkaline batteries.  
©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.  
PRINTED IN CHINA  
K2566b-0726  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

Clarion Car Video System VT1000B User Manual
Contec Universal Remote RT U27A DVR User Manual
Craftsman Trimmer 24074805 User Manual
Crest Audio DJ Equipment X 18R User Manual
Curtis Digital Photo Frame DPF151 User Manual
Danby Dehumidifier DDR6009REE User Manual
Dukane Projector AV P750U User Manual
Fisher Price CD Player N8238 0920 User Manual
Fujitsu Air Conditioner AOU12CQ User Manual
Gateway Flat Panel Television 30 inch LCD TV User Manual