UNVENTED (VENT-FREE) GAS STOVE HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
MODELS CSBNT, CSBPT, CSPBNT, CSPBPT, CSPINT, CSPIPT
Propane/LP and Natural Gas Thermostat Control Gas Log Heaters
(Burner System For Cast Iron Stoves)
WARNING: If the information in this manual is not fol-
lowed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediatelycallyourgassupplierfromaneighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
— Installationandservicemustbeperformedbyaquali-
fied installer, service agency or the gas supplier.
Save this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
WARNING: Do not use a
blower insert, heat exchanger
insertorotheraccessorynotap-
proved for use with this heater.
WARNING:Thisproductcon-
tainsand/orgenerateschemicals
known to the state of California
to cause cancer or birth defects
or other reproductive harm.
Due to high temperatures, the
applianceshouldbelocatedout
oftrafficandawayfromfurniture
and draperies.
IMPORTANT: Read this owner’s
manual carefully and completely
beforetryingtoassemble,operate
orservicethisfireplace.Improper
useofthisfireplacecancauseseri-
ousinjuryordeathfromburns,fire,
explosion, electrical shock and
carbon monoxide poisoning.
Do not place clothing or other
flammable material on or near
the appliance. Never place any
objects on the heater.
Stove becomes very hot when
running heater. Keep children
andadultsawayfromhotsurface
to avoid burns or clothing igni-
tion. Heater will remain hot for a
time after shutdown. Allow sur-
face to cool before touching.
DANGER:Carbonmonoxide
poisoning may lead to death!
CarbonMonoxidePoisoning: Early signs of carbon
monoxide poisoning resemble the flu, with head-
aches, dizziness or nausea. If you have these signs,
the heater may not be working properly. Get fresh
air at once! Have heater serviced. Some people
are more affected by carbon monoxide than others.
These include pregnant women, people with heart
or lung disease or anemia, those under the influence
of alcohol and those at high altitudes.
Carefully supervise young chil-
dren when they are in the room
with heater.
Natural and Propane/LP Gas: Natural and pro-
pane/LPgases are odorless.An odor-making agent
is added to the gas. The odor helps you detect a gas
leak. However, the odor added to the gas can fade.
Gas may be present even though no odor exists.
Keep the appliance area clear
and free from combustible ma-
terials, gasoline and other flam-
mable vapors and liquids.
Make certain you read and understand all warn-
ings. Keep this manual for reference. It is your
guide to safe and proper operation of this heater.
1. This appliance is only for use with the type of
gas indicated on the rating plate. This appliance
is not convertible for use with other gases.
2. Do not place propane/LP supply tank(s) in-
side any structure. Locate propane/LP supply
tank(s) outdoors.
WARNING: Any change to
this heater or its controls can
be dangerous.
3. If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use
any phone in your building
WARNING:Donotallowfans
to blow directly into the stove.
Avoidanydraftsthatalterburner
flame patterns. Ceiling fans can
create drafts that alter burner
flame patterns. Altered burner
patterns can cause sooting.
• immediately call your gas supplier from a
neighborʼs phone. Follow the gas supplierʼs
instructions
• if you cannot reach your gas supplier, call
the fire department
111487-01D
3
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Operating heater above elevations of 4,500
feet could cause pilot outage.
SAFETY INFORMATION
Continued
18. For propane/LP units, do not use propane/LP
tank of less than 100 lb. capacity.
4. This heater shall not be installed in a bedroom
or bathroom.
19. Provide adequate clearances around air
openings.
5. Do not place stove directly on carpeting,
vinyl tile or any combustible material other
than wood. The stove must set on a metal
or wood panel extending the full width and
depth of the appliance.
20. Screen must be completely closed before using
heater. Never run heater with screen open.
PRODUCT
IDENTIFICATION
6. Do not use this stove as a wood burning fire-
place. Use only model 111485-02/111485-01
vent-free gas log heater.
One Piece Log Set
Inside Stove Cavity
7. Do not add extra logs or ornaments such as pine
cones, vermiculite or rock wool. Using these
added items can cause sooting.
Stove
Body
8. This log heater is designed to be smokeless. If
logs ever appear to smoke, turn off heater and
call a qualified service person. Note: During
initial operation, slight smoking could occur
due to log curing and heater burning manu-
facturing residues.
Screen
9. To prevent the creation of soot, follow the
instructions in Cleaning and Maintenance,
page 14.
10. Before using furniture polish, wax, carpet
cleaners or similar products, turn heater off.
If heated, the vapors from these products may
create a white powder residue within burner
box or on adjacent walls or furniture.
Stove Door
(Shown in the
open position)
Piezo
Ignitor
Control
Knob
Figure 1 - Typical Stove Cabinet Model
with Comfort Glow Gas Log Heater
11. Thisheaterneedsfresh, outsideairventilationto
run properly. This heater has an Oxygen Deple-
tion Sensing (ODS) safety shutoff system. The
ODS shuts down the heater if not enough fresh
air is available. See Air for Combustion and
Ventilation, page 5. If heater keeps shutting
off, see Troubleshooting, page 16.
LOCAL CODES
Install and use heater with care. Follow all local
codes. In the absence of local codes, use the lat-
est edition of The National Fuel Gas Code ANSI
Z223.1/NFPA 54*.
12. Do not run heater
*Available from:
• where flammable liquids or vapors are used
or stored
American National Standards Institute, Inc.
1430 Broadway
• when under dusty conditions
13. Do not use this stove to cook food or burn paper
or other objects.
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
14. Do not use heater if any part has been exposed
to or under water. Immediately call a qualified
service technician to inspect the room heater
andtoreplaceanypartofthecontrolsystemand
any gas control which has been under water.
Quincy, MA 02269
15. Do not operate heater if any log is broken. Do
not operate heater if a log is chipped (dime-
sized or larger).
16. Turn heater off and let cool before servicing.
Only a qualified service person should service
and repair heater.
4
111487-01D
Download from Www.Somanuals.com. All Manuals Search And Download.
All spaces in homes fall into one of the three fol-
lowing ventilation classifications:
PRODUCT FEATURES
OPERATION
1. Unusually Tight Construction
2. Unconfined Space
This heater is clean burning. It requires no outside
venting. There is no heat loss out a vent or up a
chimney. Heat is generated by realistic, dancing
yellow flames. This heater is designed for vent-free
operation. State and local codes in some areas
prohibit the use of vent-free heaters.
3. Confined Space
The information on pages 5 through 7 will help
you classify your space and provide adequate
ventilation.
Unusually Tight Construction
SAFETY PILOT
The air that leaks around doors and windows may
provide enough fresh air for combustion and ven-
tilation. However, in buildings of unusually tight
construction, you must provide additional fresh air.
This heater has a pilot with an Oxygen Deple-
tion Sensing (ODS) safety shutoff system. The
ODS/pilot is a required feature for vent-free room
heaters. The ODS/pilot shuts off the heater if there
is not enough fresh air.
Unusually tight construction is defined as
construction where:
PIEZO IGNITION SYSTEM
Thisheaterhasapiezoignitor.Thissystemrequiresno
matches, batteries or other sources to light heater.
a. walls and ceilings exposed to the out-
side atmosphere have a continuous
water vapor retarder with a rating of one
perm (6 x 10-11 kg per pa-sec-m2) or less
with openings gasketed or sealed and
AIR FOR COMBUSTION
AND VENTILATION
b. weather stripping has been added on
openable windows and doors and
c. caulking or sealants are applied to areas
such as joints around window and door
frames, between sole plates and floors,
between wall-ceiling joints, between
wall panels, at penetrations for plumb-
ing, electrical and gas lines and at other
openings.
WARNING: This heater shall
notbeinstalledinaconfinedspace
or unusually tight construction
unless provisions are provided
for adequate combustion and
ventilation air. Read the following
instructionstoinsureproperfresh
air for this and other fuel-burning
appliances in your home.
If your home meets all of the three criteria
above,youmustprovideadditionalfreshair.
See Ventilation Air From Outdoors, page 7.
If your home does not meet all of the three
criteriaabove,proceedtoDeterminingFresh-
Air Flow For Heater Location, page 6.
Todayʼs homes are built more energy efficient
than ever. New materials, increased insulation and
new construction methods help reduce heat loss
in homes. Home owners weather strip and caulk
around windows and doors to keep the cold air out
and the warm air in. During heating months, home
owners want their homes as airtight as possible.
Confined and Unconfined Space
The National Fuel Gas Code ANSI Z223.1/NFPA
54 defines a confined space as a space whose vol-
ume is less than 50 cubic feet per 1,000 Btu per hour
(4.8 m3 per kw) of the aggregate input rating of all
appliances installed in that space and an unconfined
space as a space whose volume is not less than 50
cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of
the aggregate input rating of all appliances installed
in that space. Rooms communicating directly with
the space in which the appliances are installed*,
through openings not furnished with doors, are
considered a part of the unconfined space.
While it is good to make your home energy effi-
cient, your home needs to breathe. Fresh air must
enter your home.All fuel-burning appliances need
fresh air for proper combustion and ventilation.
Exhaust fans, fireplaces, clothes dryers and fuel
burning appliances draw air from the house to
operate. You must provide adequate fresh air for
these appliances. This will insure proper venting
of vented fuel-burning appliances.
* Adjoining rooms are communicating only if
there are doorless passageways or ventilation grills
between them.
PROVIDING ADEQUATE VENTILATION
The following are excerpts from National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Section 5.3,
Air for Combustion and Ventilation.
111487-01D
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: 51,200 Btu/Hr (maximum the
space can support)
AIR FOR COMBUSTION
AND VENTILATION
70,000 Btu/Hr (actual amount of
Btu/Hr used)
Continued
DETERMINING FRESH-AIR FLOW
FOR HEATER LOCATION
The space in the above example is a confined
space because the actual Btu/Hr used is more than
the maximum Btu/Hr the space can support. You
must provide additional fresh air. Your options
are as follows:
Determining if You Have a Confined or
Unconfined Space
Use this work sheet to determine if you have a
A. Rework worksheet, adding the space of an
adjoining room. If the extra space provides an
unconfined space, remove door to adjoining
room or add ventilation grills between rooms.
See Ventilation Air From Inside Building.
confined or unconfined space.
Space: Includes the room in which you will
install heater plus any adjoining rooms with door-
less passageways or ventilation grills between
the rooms.
B. Vent room directly to the outdoors. See Ven-
tilation Air From Outdoors, page 7.
1. Determine the volume of the space (length x
width x height).
C. Install a lower Btu/Hr heater, if lower Btu/Hr
size makes room unconfined.
Length x Width x Height = ________cu. ft.
(volume of space)
If the actual Btu/Hr used is less than the maxi-
mum Btu/Hr the space can support, the space is
an unconfined space. You will need no additional
fresh air ventilation.
Example: Space size 20 ft. (length) x 16 ft.
(width) x 8 ft. (ceiling height) = 2560 cu. ft.
(volume of space)
Ifadditionalventilationtoadjoiningroomissup-
plied with grills or openings, add the volume of
these rooms to the total volume of the space.
WARNING: If the area in
which the heater may be oper-
ated is smaller than that defined
as an unconfined space or if the
building is of unusually tight
construction, provide adequate
combustion and ventilation air
byoneofthemethodsdescribed
in the National Fuel Gas Code,
ANSI Z223.1/NFPA 54, Section
5.3 or applicable local codes.
2. Multiply the space volume by 20 to determine
the maximum Btu/Hr the space can support.
(volume of space) x 20 = (maximum Btu/Hr
the space can support)
Example: 2560 cu. ft. (volume of space) x 20 =
51,200 (maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances
in the space.
Vent-free heater
________ Btu/Hr
________ Btu/Hr
Gas water heater*
Gas furnace
Vented gas heater
Gas fireplace logs
Other gas appliances* + _______ Btu/Hr
Total = _______ Btu/Hr
* Do not include direct-vent gas appliances.
Direct-vent draws combustion air from the
outdoors and vents to the outdoors.
________ Btu/Hr
________ Btu/Hr
________ Btu/Hr
VENTILATION AIR
Ventilation Air From Inside Building
This fresh air would come from an adjoining un-
confined space. When ventilating to an adjoining
unconfined space, you must provide two perma-
nent openings: one within 12" of the ceiling and
one within 12" of the floor on the wall connecting
the two spaces (see options 1 and 2, Figure 2,
page 7). You can also remove door into adjoining
room (see option 3, Figure 2, page 7). Follow the
National Fuel Gas Code, ANSI Z223.1/NFPA 54,
Section 5.3, Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
Example:
Gas water heater
Vent-free heater
Total
_4_0_,0_0_0___ Btu/Hr
+ _3_0_,0_0_0___ Btu/Hr
= _7_0_,0_0_0___ Btu/Hr
4. Compare the maximum Btu/Hr the space can
support with the actual amount of Btu/Hr used.
_______ Btu/Hr (maximum the space can support)
______ Btu/Hr (actual amount of Btu/Hr used)
6
111487-01D
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR FOR COMBUSTION
UNPACKING
1. Lift off corrugated box enclosing stove
body crating.
AND VENTILATION
Continued
2. Remove screws fastening back and top of wood
frameenclosure.Twoormorepeoplemustcare-
fully lift stove up and out of wooden crate.
12"
3. Remove plastic bag from stove body.
4. Remove back panel from stove (see Figure 4).
Use an adjustable wrench or a 10 mm socket.
Remove four (4) bolts and washers. Keep bolts
and washers to reattach back panel later.
Ventilation
Ventilation Grills
Into Adjoining Room,
Option 2
Grills
Into Adjoining
Room,
Or
Remove
Door into
Adjoining
Room,
Option
3
Option 1
5. Remove bubble-wrapped log set, rod and
screen from stove. Remove all protective
packaging applied for shipment.
12"
6. Check all items for any shipping damage. If
damaged, promptly inform dealer where you
bought heater. Some fiber flakes may fall from
logs. This is acceptable.
7. Place freestanding stove near desired location
in room.
Figure 2 - Ventilation Air from Inside
Building
Top of Wood
Frame Enclosure
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or
ducts. You must provide two permanent openings:
one within 12" of the ceiling and one within 12"
of the floor. Connect these items directly to the
outdoors or spaces open to the outdoors. These
spaces include attics and crawl spaces. Follow the
National Fuel Gas Code, ANSI Z223.1/NFPA 54,
Section 5.3, Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
STOVE TOP
Back of Wood Frame Enclosure
IMPORTANT: Do not provide openings for inlet
or outlet air into attic if attic has a thermostat-
controlled power vent. Heated air entering the attic
will activate the power vent.
Back
Panel
Screws
Back
Panel
Screws
Ventilated
Outlet
Attic
Air
Outlet
STOVE BACK
A
ir
To Attic
Figure 4 - Unpacking Stove from Wooden
Shipping Enclosure
To
Crawl
Space
Inlet
Air
Ventilated
Crawl Space
Inlet Air
Figure 3 - Ventilation Air from Outdoors
111487-01D
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: Vent-free heaters add moisture to
the air.Although this is beneficial, installing heater
in rooms without enough ventilation air may cause
mildew to form from too much moisture. See Air
for Combustion and Ventilation, page 5.
INSTALLATION
NOTICE:Thisheaterisintended
for use as supplemental heat.
Use this heater along with your
primary heating system. Do not
install this heater as your pri-
mary heat source. If you have a
centralheatingsystem,youmay
run system’s circulating blower
whileusingheater.Thiswillhelp
circulatetheheatthroughoutthe
house. In the event of a power
outage, you can use this heater
as your primary heat source.
CHECK GAS TYPE
Use the correct gas type (natural or propane/LP) for
your unit. If your stove heater gas type is different
from your house gas type, do not install heater.
Call dealer where you bought heater for proper
type heater.
WARNING: This appliance
is equipped for (natural or pro-
pane/LP) gas. Field conversion
is not permitted.
CLEARANCES TO COMBUSTIBLES
(Vent-Free Operation Only)
WARNING: A qualified ser-
vice person must install heater.
Follow all local codes.
WARNING: Maintain the
minimumclearances.Ifyoucan,
providegreaterclearancesfrom
floor, ceiling and adjoining side
and back walls.
WARNING: Never install the
heater
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture,
clothing or other flammable
objectsarelessthan42inches
from the front, top or sides of
the heater
Carefully follow the instructions below. This stove
is a freestanding unit designed to set directly on the
floor. DO NOT place stove directly on carpeting,
vinyl tile or any combustible material other than
wood. The stove must be set on a metal or wood
panel extending the full width and depth of the
stove for these floor coverings. Important: You
must maintain minimum wall and ceiling clear-
ances during installation. The minimum clearances
are shown in Figure 5, page 9. Measure from
outermost point of stove top.
• in high traffic areas
• in windy or drafty areas
CAUTION: This heater cre-
ates warm air currents. These
currents move heat to wall sur-
faces next to heater. Installing
heater next to vinyl or cloth wall
coverings or operating heater
where impurities (such as, but
not limited to, tobacco smoke,
aromatic candles, cleaning flu-
ids,oilorkerosenelamps,etc.)in
the air exist, may discolor walls
or cause odors.
Minimum Wall and Ceiling Clearances
(see Figure 5, page 9)
A. Clearances from outermost point of stove top
to any combustible side wall should not be
less than 12 inches.
B. Clearances from outermost point of stove top
to any combustible back wall should not be less
than 6 inches (includes corner installations).
C. Clearances from the stove top to the ceiling
should not be less than 48 inches.
8
111487-01D
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO GAS SUPPLY
INSTALLATION
Continued
WARNING: This appliance
requires a 1/2" NPT (National
PipeThread)inletconnectionto
the pressure regulator.
Ceiling
48"
Minimum
12"
12"
Side Wall
Minimum
Minimum
Side Wall
WARNING:Aqualifiedservice
personmustconnectheatertogas
supply. Follow all local codes.
CAUTION: Never connect
propane/LPheaterdirectlytothe
propane/LP supply. This heater
requires an external regulator
(not supplied). Install the exter-
nalregulatorbetweentheheater
and propane/LP supply.
Front View
Back Wall
6 "
Minimum
12 "
12 "
Minimum
Minimum
Side Wall
Side Wall
Front of Stove Unit
WARNING: Never connect
naturalgasheatertoprivate(non-
utility)gaswells.Thisgasiscom-
monly known as wellhead gas.
Top View
Corner
Wall
6 "
Minimum
Installation Items Needed
Before installing heater, make sure you have the
items listed below.
Wall
•
external regulator [propane/LP only] (supplied
by installer)
6 "
Front of Stove
Unit
Minimum
•
•
•
•
•
•
•
piping to stove location (check local codes)
sealant (resistant to propane/LP gas)
equipment shutoff valve *
test gauge connection *
sediment trap
Ceiling
48"
Minimum
tee joint
Back Wall
pipe wrench
6"
Minimum
*ACSAdesign-certified equipment shutoff valve
with 1/8" NPT tap is an acceptable alternative to
test gauge connection. Purchase the optional CSA
design-certified equipment shutoff valve from your
dealer. See Accessories, page 19.
Front of
Stove Unit
The gas inlet connection for the stove heater is
located on the lower right-hand side of the stove
when viewed from the front of the unit. The gas
connection can be made either through the bottom
right side or through the lower back opening as
illustrated in Figure 6, page 10. Make sure gas log
heater is secured to the stove cavity assembly.
Floor
Side View
Figure 5 - Minimum Clearance to Walls
and Ceiling (Stove May Vary Depending
on Model)
111487-01D
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
WARNING: Use pipe joint
sealant that is resistant to liquid
petroleum (LP) gas.
Continued
For propane/LP units, the installer must supply
an external regulator. The external regulator will
reduce incoming gas pressure. You must reduce
incoming gas pressure to between 11 and 14 inches
of water. If you do not reduce incoming gas pres-
sure, heater regulator damage could occur. Install
external regulator with the vent pointing down as
shown in Figure 7. Pointing the vent down protects
it from freezing rain or sleet.
We recommend that you install a sediment trap in
supply line as shown in Figure 8. Locate sediment
trap where it is within reach for cleaning. Install
in piping system between fuel supply and heater.
Locate sediment trap where trapped matter is not
likely to freeze.Asediment trap traps moisture and
contaminants. This keeps them from going into
heater controls. If sediment trap is not installed or
is installed wrong, heater may not run properly.
CAUTION: For propane/LP
units, use only new, black iron
or steel pipe. Internally-tinned
copper tubing may be used in
certain areas. Check your local
codes.Usepipeof1/2"diameter
or greater to allow proper gas
volume to heater. If pipe is too
small, undue loss of volume
will occur.
CAUTION: Avoid damage to
regulator. Hold gas regulator
with wrench when connecting it
to gas piping and/or fittings.
External
Propane/LP
Regulator
Supply Tank
Installation must include an equipment shutoff
valve, union and plugged 1/8" NPT tap. Locate
NPT tap within reach for test gauge hook up. NPT
tap must be upstream from heater (see Figure 8).
Vent
Pointing
Down
IMPORTANT:Install equipment shutoff valve in an
accessiblelocation.Theequipmentshutoffvalveisfor
turning on or shutting off the gas to the appliance.
Figure 7 - External Regulator For
Propane/LP Gas With Vent Pointing Down
Check your building codes for any special re-
quirements for locating equipment shutoff valve
to fireplaces.
From
CSA Design-
External
Regulator
(11"
W.C.** to
14" W.C.
Pressure)
Certified Equipment
Shutoff Valve With
1/8" NPT Tap*
Apply pipe joint sealant lightly to male NPT
threads. This will prevent excess sealant from
going into pipe. Excess sealant in pipe could result
in clogged heater valves.
Gas
Regulator
(Propane/LP)
Side View
Back View
Back
Stove
Panel
Front
of
Stove
Unit
3"
Minimum
Approved
Tee Pipe Cap
Joint Nipple
Flexible Gas
Hose (if allowed
by local codes)
Gas Inlet
Connection
Access
Gas Log
Heater
Product
Identification
Label
Sediment Trap
Figure 8 - Gas Connection
* Purchase the optional CSA design-certified
equipment shutoff valve from your dealer. See
Accessories, page 19.
Figure 6 - Gas Regulator Location and
Gas Line Access Into Stove Cabinet
**Minimum inlet pressure for purpose of input
adjustment.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
111487-01D
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see Figure 9).
INSTALLATION
Continued
CHECKING GAS CONNECTIONS
2. Pressurize supply piping system by either
opening propane/LP supply tank valve for
propane/LP gas or opening main gas valve
located on or near gas meter for natural gas
or using compressed air.
WARNING:Testallgaspiping
and connections, internal and
external to unit, for leaks after
installing or servicing. Correct
all leaks at once.
3. Check all joints from gas meter for natural or
propane/LPsupply to equipment shutoff valve
(see Figure 10 or Figure 11, page 10). Apply
noncorrosive leak detection fluid to gas joints.
Bubbles forming show a leak.
WARNING: Never use an
open flame to check for a leak.
Applyanoncorrosiveleakdetec-
tion fluid to all joints. Bubbles
forming show a leak. Correct all
leaks at once.
4. Correct all leaks at once.
Equipment
Shutoff Valve
Open
Closed
CAUTION: Make sure exter-
nal regulator has been installed
betweenpropane/LPsupplyand
propane/LP heater. See guide-
lines under Connecting to Gas
Supply, page 9.
Figure 9 - Equipment Shutoff Valve
PRESSURE TESTING HEATER GAS
CONNECTIONS
1. Open equipment shutoff valve (see Figure 9).
2. Open main gas valve located on or near gas
meter for natural gas or open propane/LP
supply tank valve.
PRESSURE TESTING GAS SUPPLY
PIPING SYSTEM
3. Make sure control knob of heater is in the
OFF position.
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
4. Checkalljointsfromequipmentshutoffvalveto
control valve (see Figure 10 or Figure 11, page
12). Apply noncorrosive leak detection fluid to
gas joints. Bubbles forming show a leak.
1. Disconnect appliance with its appliance main
gas valve (control valve) and equipment
shutoff valve from gas supply piping system.
Pressures in excess of 1/2 psig will damage
heater regulator.
5. Correct all leaks at once.
6. Light heater (see Operating Heater, page 13).
Check all other internal joints for leaks.
2. Cap open end of gas pipe where equipment
shutoff valve was connected.
7. Turn off heater (see To Turn Off Gas to Appli-
ance, page 14).
3. Pressurize supply piping system by either
opening propane/LP supply tank valve for
propane/LP gas or opening main gas valve
located on or near gas meter for natural gas
or using compressed air.
Equipment
Shutoff Valve
Propane/LP
Supply Tank
4. Check all joints of gas supply piping system.
Apply noncorrosive leak detection fluid to gas
joints. Bubbles forming show a leak.
5. Correct all leaks at once.
6. Reconnect heater and equipment shutoff
valve to gas supply. Check reconnected fit-
tings for leaks.
Control Valve
Location
Figure 10 - Checking Gas Joints on
Propane/LP Gas Unit
111487-01D
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING LOG SET
INSTALLATION
1. Set one-piece log on heater base as shown in
Figure 14. Make sure middle section at bot-
tom of log is seated into "U" shaped cutout in
center of heater base. Log will fit securely on
base. IMPORTANT: Make sure log does not
cover any burner ports and does not touch the
stove cavity (see Figure 14).
Continued
Equipment
Shutoff Valve
Gas Meter
2. Fasten back panel to stove with four (4) bolts
and washers removed in step 4 of Unpacking,
page7. Makesureproductidentificationlabelis
located on the outside lower left-hand corner.
Control Valve
Location
3. Place freestanding stove in desired position
being careful not to damage gas connections.
Be sure to maintain clearances to combustibles
and wall clearances as outlined on page 8.
Figure 11 - Checking Gas Joints on
Natural Gas Unit
One-Piece
Log Set
INSTALLING ROD AND SCREEN
1. Insert rod through small rings located at top
of screen (see Figure 12).
2. From back of stove, insert rod into hole
located inside right front of stove as shown
in Figure 13.
Middle Section
at Bottom of
Log Set
3. Slip left side of rod down into slot on inside
left front of stove (see Figure 13).
Rod
Burner
Rings
"U" Shaped
Cutout in
Heater
Chassis
Base
Figure 14 - Installing One-Piece Stove
Log Set
Burner Porting Areas
(double slotted
rectangular openings
One-Piece
Log Set
Figure 12 - Assembling Rod and Screen
Safety
Pilot
Location
Slot on Inside
Hole on Inside
Rod with
Screen
Left Front of
Stove
Right Front of
Stove
Assembled
Figure 15 - Top View of One-Piece Log
Set on Gas Log Heater
Figure 13 - Installing Screen Into Stove
(View From Back of Stove)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
111487-01D
4. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor.
If you smell gas, STOP! Follow “B” in the
safety information, column 1. If you donʼt
smell gas, go to the next step.
OPERATING HEATER
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not fol-
low these instructions exactly,
a fire or explosion may result
causing property damage, per-
sonal injury or loss of life.
5. Turn control knob counterclockwise
to the PILOT position. Press in control knob
for five (5) seconds (see Figure 16).
Note: You may be running this heater for
the first time after hooking up to gas sup-
ply. If so, the control knob may need to be
pressed in for 30 seconds or more. This will
allow air to bleed from the gas system.
A. This appliance has a pilot which must be
lighted by hand. When lighting the pilot,
follow these instructions exactly.
6. Withcontrolknobpressedin,pressandrelease
ignitorbutton.Thiswilllightpilot.Thepilotis
attached to the front burner. If needed, keep
pressing ignitor button until pilot lights.
B. BEFORE LIGHTING smell all around the
appliance area for gas. Be sure to smell next
to the floor because some gas is heavier than
air and will settle on the floor.
Note: If pilot does not stay lit, contact a
qualified service person or gas supplier for
repairs. Until repairs are made, light pilot
with match. To light pilot with match, see
Manual Lighting Procedure, page 14.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use
any phone in your building.
7. Keep control knob pressed in for30 seconds
after lighting pilot.After 30 seconds, release
control knob.
• Immediately call your gas supplier from
a neighborʼs phone. Follow the gas
supplierʼs instructions.
• If control knob does not pop out when
released, contact a qualified service person
or gas supplier for repairs.
• If you cannot reach your gas supplier, call
the fire department.
C. Use only your hand to push in or turn the
gas control knob. Never use tools. If the
knob will not push in or turn by hand, donʼt
try to repair it, call a qualified service tech-
nician or gas supplier. Force or attempted
repair may result in a fire or explosion.
Note: If pilot goes out, repeat steps 3
through 7. This heaterhas a safety interlock
system. Wait one (1) minute for system to
reset before lighting pilot again.
8. Turn control knob counterclockwise
to desired heating level. The burners should
light. Set control knob to any heat level
between HI and LO.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified
servicetechniciantoinspecttheapplianceand
to replace any part of the control system and
any gas control which has been under water.
CAUTION: Do not try to ad-
just heating levels by using the
equipment shutoff valve.
LIGHTING
INSTRUCTIONS
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Orangeflamewillalsobepresent.
Open a window to vent smell.
This will only last a few hours.
Ignitor Button
Control Knob
Figure 16 - Control Knob and Ignitor
Button Location
Thermocouple
1. STOP! Read the safety information, abovc.
2. Make sure equipment shutoff valve is
fully open.
Pilot Burner
3. Turn control knob clockwise
OFF position.
to the
Figure 17 - Pilot
111487-01D
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Note: The correct pilot flame on natural gas units
will have a slight curve, but flame should be blue
and have no yellow or orange color.
OPERATING HEATER
Continued
TO TURN OFF GAS
TO APPLIANCE
Thermocouple
Pilot
Burner
Shutting Off Heater
Turn control knob clockwise
OFF position.
to the
Figure 18 - Correct Pilot Flame Pattern
(Propane/LP Shown)
Shutting Off Burners Only (pilot stays lit)
Turn control knob clockwise
PILOT position.
to the
Pilot Burner
Thermocouple
THERMOSTAT CONTROL
OPERATION
The thermostat control knob can be set to any
comfort level between HI and LO. The ther-
mostat will gradually modulate the heat output
and flame height from higher to lower settings
or pilot, in order to maintain the comfort level
you select. The ideal comfort setting will vary
by household depending upon the amount of
space to be heated, the output of the central
heating system, etc.
Figure 19 - Incorrect Pilot Flame Pattern
(Propane/LP Shown)
MAIN BURNER
Periodically inspect all burner flame holes with
the heater running. All slotted burner flame holes
should be open with yellow flame present. All
round burner flame holes should be open with a
small blue flame present. Some burner flame holes
may become blocked by debris or rust, with no
flame present. If so, turn off heater and let cool.
Remove blockage. Blocked burner flame holes
will create soot.
Note: Selecting the HI setting with the control
knob will cause the burner to remain fully on,
without modulating down in most cases.
MANUAL LIGHTING
PROCEDURE
1. Follow steps 1 through 5 under Lighting
Instructions, page 13.
CLEANING AND
MAINTENANCE
2. Depress control knob and light pilot with
match.
WARNING: Turn off heater
and let cool before cleaning.
3. Keep control knob pressed in for30 seconds
after lighting pilot.After 30 seconds, release
control knob. Now follow step 8 in Lighting
Instructions, page 13.
CAUTION:Youmustkeepcon-
trol areas, burner and circulating
air passageways of heater clean.
Inspect these areas of heater
before each use. Have heater
inspected yearly by a qualified
service person. Heater may need
more frequent cleaning due to
excessivelintfromcarpeting,pet
hair, bedding material, etc.
INSPECTING BURNERS
Check pilot flame pattern and burner flame pat-
terns often.
PILOT FLAME PATTERN
Figure 18 shows a correct pilot flame pattern.
Figure 19 shows an incorrect pilot flame pattern.
The incorrect pilot flame is not touching the
thermocouple. This will cause the thermocouple
to cool. When the thermocouple cools, the heater
will shut down.
If pilot flame pattern is incorrect, as shown in
Figure 19
WARNING: Failure to keep
the primary air opening(s) of
the burner(s) clear may result in
sooting and property damage.
•
turn heater off (see To Turn Off Gas to
Appliance)
•
see Troubleshooting, page 16
14
111487-01D
Download from Www.Somanuals.com. All Manuals Search And Download.
Injector Holder
(May Be Brass or
Aluminum Depending
on Model)
CLEANING AND
MAINTENANCE
Burner
Tube
Continued
BURNER INJECTOR HOLDER AND
PILOT AIR INLET HOLE
Primary Air Inlet
Holes (Shape of
Holes May Vary
by Model)
The primary air inlet holes allow the proper amount
of air to mix with the gas. This provides a clean
burning flame. Keep these holes clear of dust, dirt,
lint and pet hair. Clean these air inlet holes prior to
each heating season. Blocked air holes will create
soot. We recommend that you clean the unit every
three months during operation and have heater
inspected yearly by a qualified service person.
Figure 20 - Injector Holder On Outlet
Burner Tube
Ports/Slots
Burner
Tube
We also recommend that you keep the burner
tube and pilot assembly clean and free of dust
and dirt. To clean these parts we recommend us-
ing compressed air no greater than 30 PSI. Your
local computer store, hardware store or home
center may carry compressed air in a can. You
can use a vacuum cleaner in the blow position. If
using compressed air in a can, please follow the
directions on the can. If you don't follow directions
on the can, you could damage the pilot assembly.
Note: Removing the rear panel and top grates of
your stove will make cleaning easier.
Pilot
Assembly
Pilot Air
Inlet Hole
1. Shut off the unit, including the pilot. Allow
the unit to cool for at least thirty minutes.
Figure 21 - Pilot Inlet Air Hole
2. Inspect burner, pilot and primary air inlet
holes on injector holder for dust and dirt (see
Figure 20).
LOGS
•
If you remove logs for cleaning, refer to Install-
ing Log Set, page 12, to properly replace logs.
3. Blow air through the ports/slots and holes in
the burner.
•
Replace log(s) if broken or chipped (dime-sized
or larger).
4. Check the injector holder located at the end
of the burner tube again. Remove any large
particles of dust, dirt, lint or pet hair with a
soft cloth or vacuum cleaner nozzle.
5. Blow air into the primary air holes on the
injector holder.
6. In case any large clumps of dust have now been
pushed into the burner repeat steps 3 and 4.
Clean the pilot assembly also. A yellow tip on the
pilot flame indicates dust and dirt in the pilot as-
sembly. There is a small pilot air inlet hole about
two inches from where the pilot flame comes out
of the pilot assembly (see Figure 21). With the unit
off, lightly blow air through the air inlet hole. You
may blow through a drinking straw if compressed
air is not available.
111487-01D
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
WARNING: Turn off heater and let cool before servicing. Only a
qualified service person should service and repair heater.
CAUTION: Never use a wire, needle or similar object to clean
ODS/pilot. This can damage ODS/pilot unit.
Note: All troubleshooting items are listed in order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed,
there is no spark at ODS/pilot
1. Ignitor electrode not con- 1. Reconnect ignitor cable
nected to ignitor cable
2. Ignitor cable pinched or 2. Free ignitor cable if pinched
wet
by any metal or tubing. Keep
ignitor cable dry
3. Broken ignitor cable
4. Bad piezo ignitor
5. Ignitor electrode broken
3. Replace ignitor cable
4. Replace piezo ignitor
5. Replace pilot assembly
6. Ignitor electrode positioned 6. Replace pilot assembly
wrong
When ignitor button is pressed,
there is spark at ODS/pilot but
no ignition
1. Gassupplyturnedofforequip- 1. Turn on gas supply or open
ment shutoff valve closed
2. Control knob not in PILOT 2. Turn control knob to PILOT
position position
3. Control knob not pressed in 3. Press in control knob while in
while in PILOT position PILOT position
equipment shutoff valve
4. Air in gas lines when installed 4. Continue holding down con-
trol knob. Repeat igniting op-
eration until air is removed
5. ODS/pilot is clogged
5. Clean ODS/pilot (see Cleaning
and Maintenance, page 14) or
replace ODS/pilot assembly
6. Gas regulator setting is not 6. Replace gas control
correct
7. Depleted gas supply (pro- 7. Contact local propane/LP gas
pane/LP only)
company
ODS/pilot lights but flame goes
out when control knob is re-
leased
1. Control knob not fully 1. Press in control knob fully
pressed in
2. Control knob not pressed in 2. After ODS/pilot lights, keep con-
long enough
3. Equipment shutoff valve not 3. Fully open equipment shutoff
fully open valve
4. Pilot flame not touching 4. A) Contact local natural or
trol knob pressed in 30 seconds
thermocouple, which allows
thermocouple to cool, caus-
ing pilot flame to go out. This
problem could be caused by
one or both of the following:
A) Low gas pressure
propane/LP gas company
B) Clean ODS/pilot (see
Cleaning and Maintenance,
page 14) or replace ODS/pilot
assembly
B) Dirty or partially clogged
ODS/pilot
5. Thermocouple connection 5. Hand tighten until snug, then
loose at control valve
6. Thermocouple damaged
7. Control valve damaged
tighten 1/4 turn more
6. Replace pilot assembly
7. Replace control valve
16
111487-01D
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after ODS/
pilot is lit
1. Clean burner (see Cleaning
and Maintenance, page 14) or
replace burner orifice
1. Burner orifice clogged
2. Contact local natural or pro-
pane/LP gas company
2. Inlet gas pressure is too low
Delayed ignition burner
1. Contact local natural or pro-
pane/LP gas company
2. Clean burner (see Cleaning
and Maintenance, page 14) or
replace burner orifice
1. Manifold pressure is too low
2. Burner orifice clogged
Burner backfiring during com-
bustion
1. Clean burner (see Cleaning
and Maintenance, page 14) or
replace burner orifice
1. Burner orifice is clogged or
damaged
2. Replace damaged burner
3. Replace gas control
2. Damaged burner
3. Gas regulator defective
Slightsmokeorodorduringinitial
operation
1. Check burner for dirt and
debris. If found, clean burner
(see Cleaning and Mainte-
nance, page 14)
1. Not enough air
2. Replace gas control
3. Problem will stop after a few
hours of operation
2. Gas regulator defective
3. Residues from manufacturing
processes and logs curing
Moisture/condensation noticed
on windows
1. Refer to Air for Combustion
and Ventilation requirements
(page 5)
1. Not enough combustion/ven-
tilation air
Heaterproducesawhistlingnoise
when burner is lit
1. TurncontrolknobtoLOposition
and let warm up for a minute
2. Operate burner until air is
removed from line. Have gas
line checked by local natural
or propane/LP gas company
3. Observe minimum installation
clearances (see page 8)
1. Turning control knob to HI
position when burner is cold
2. Air in gas line
3. Air passageways on heater
blocked
4. Clean burner (see Cleaning
and Maintenance, page 14) or
replace burner orifice
4. Dirty or partially clogged
burner orifice
Dark residue on logs or inside
of fireplace
1. Properly locate logs (see In-
stalling Log Set, page 12)
2. Eliminate source of drafts
around heater
3. Clean out air holes at burner
inlet. Periodically repeat as
needed
1. Improper log placement
2. Drafts or other air currents
affecting flame pattern
3. Air holes at burner inlet
blocked
4. Remove blockage
4. Burner flame holes blocked
White powder residue forming
within burner box or on adjacent
walls or furniture
1. Turn heater off when using
furniture polish, wax, carpet
cleaners or similar products
1. When heated, vapors from
furniture polish, wax, carpet
cleaners, etc. may turn into
white powder residue
111487-01D
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone. Fol-
low the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint,
paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These
fumes may mix with combustion air and create odors. These odors will disappear over time.
POSSIBLE CAUSE
OBSERVED PROBLEM
REMEDY
1. Metalexpandingwhileheating
or contracting while cooling
Heater produces a clicking/tick-
ing noise just after burner is lit
or shut off
1. Thisiscommonwithmostheat-
ers.Ifnoiseisexcessive,contact
qualified service person
1. Heater burning vapors from
paint, hair spray, glues,
cleaners, chemicals, new
carpet, etc. (See IMPOR-
TANT statement above)
2. Gas leak. See Warning
statement at top of
page
Heater produces unwanted
odors
1. Open window and ventilate
room. Stop using odor caus-
ing products while heater is
running
2. Locate and correct all leaks
(see Checking Gas Connec-
tions, page 11)
1. Not enough fresh air is
available
2. Low line pressure
Heater shuts off in use (ODS
operates)
1. Open window and/or door for
ventilation
2. Contact local natural or pro-
pane/LP gas company
3. ODS/pilot is partially
clogged
3. Clean ODS/pilot (see Cleaning
and Maintenance, page 14)
1. Gas leak. See Warning
statement at top of
page
Gasodorevenwhencontrolknob
is in OFF position
1. Locate and correct all leaks
(see Checking Gas Connec-
tions, page 11)
2. Control valve defective
2. Replace control valve
1. Foreign matter between con-
trol valve and burner
Gas odor during combustion
1. Take apart gas tubing and
remove foreign matter
2. Gas leak. See Warning
statement at top of
page
2. Locate and correct all leaks
(see Checking Gas Connec-
tions, page 11)
18
111487-01D
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS UNDER WARRANTY
SPECIFICATIONS
Contact authorized dealers of this product. If
they canʼt supply original replacement part(s),
call DESA Heating Productsʼ Technical Service
Department at 1-866-672-6040.
CSBPT, CSPBPT, CSPIPT
(Includes 111485-01 Burner Chassis)
Btu (Variable)
Type Gas
16,000/30,000
Propane/LP Only
Piezo
When calling DESA Heating Products, have ready
Ignition
•
•
•
•
•
•
your name
Pressure Manifold
8" W.C.
your address
Inlet Gas Pressure (in. of water)
Maximum
model and serial numbers of your heater
how heater was malfunctioning
type of gas used (propane/LP or natural gas)
purchase date
14"
Minimum*
11"
Shipping Weight
* For input adjustment
265 lbs.
Usually, we will ask you to return the part to
the factory.
CSBNT, CSPBNT, CSPINT
(Includes 111485-02 Burner Chassis)
PARTS NOT UNDER WARRANTY
Btu (Variable)
Type Gas
Ignition
16,000/30,000
Natural Gas Only
Piezo
Contact authorized dealers of this product. If they
canʼt supply original replacement part(s), either
contact your nearest Parts Central (see page 23)
or call DESAHeating Products at 1-866-672-6040
for referral information.
Pressure Manifold 3.5" W.C.
Inlet Gas Pressure (in. of water)
Maximum
Minimum*
Shipping Weight
10.5"
5"
265 lbs.
When calling DESA Heating Products, have ready
•
•
model number of your heater
the replacement part number
* For input adjustment
ACCESSORIES
SERVICE HINTS
Purchase these heater accessories from your local
dealer. If they can not supply these accessories,
call DESA Heating Products at 1-866-672-6040
for referral information. You can also write to the
address listed on the back page of this manual.
When Gas Pressure Is Too Low
•
•
•
•
pilot will not stay lit
burners will have delayed ignition
heater will not produce specified heat
propane/LP gas supply may be low
You may feel your gas pressure is too low. If so,
contact your local propane/LP gas supplier.
TECHNICAL SERVICE
EQUIPMENT SHUTOFF VALVE
GA5010
Forallmodels. Equipment shutoff valve with 1/8"
You may have further questions about installation,
operation or troubleshooting. If so, contact DESA
Heating ProductsʼTechnical Service Department at
1-866-672-6040. When calling, please have your
model and serial numbers of your heater ready.
NPT tap. Fits 1/2" NPT pipe.
CLEANING KIT - CCK
(Not Shown)
For all models. Your vent-free gas appliance re-
quires regular cleaning and maintenance to prevent
performance problems. This kit gives you the tools
and instructions to make it easy to clean all critical
areas of your appliance.
You can also visit DESAHeating Productsʼtechni-
REPLACEMENT PARTS
Note: Use only original replacement parts. This
will protect your warranty coverage for parts
replaced under warranty.
INFORMATION VIDEO - 108917-01
Forallmodels.Acareandmaintenancevideoisavail-
ablebycalling1-866-672-6040.Youmayalsoemail
your request to [email protected].
111487-01D
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED PARTS BREAKDOWN
MODELS 111485-01 AND 111485-02
1
17
2
15
9
7
8
10
6
12
5
15
4
18
18
11
13
3
14
16
18
20
Download from Www.Somanuals.com. All Manuals Search And Download.
111487-01D
PARTS LIST
This list contains replaceable parts used in your stove. For replacement parts see Replacement Parts
on page 19 of this manual.
KEY
NO.
PART NUMBER
111485-01
111485-02
DESCRIPTION
QTY
1
104026-01
098249-01
**
104026-01
098249-01
**
Stove Log
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
7
2
Nut, M5
3
Painted Base Assembly
Bracket, Regulator
Gas Regulator
Inlet Tube
4
104454-01
098867-10
104425-01
104424-03
099056-19
111124-01
102980-01
101329-22
104472-01
099211-01
102445-01
099387-09
098271-10
104286-01
M11084-38
104454-01
098867-14
104425-01
104424-03
099056-26
111124-01
102980-01
101329-21
104472-01
099211-01
102445-01
099387-09
098271-10
104285-01
M11084-38
5
6
7
Outlet Burner Tube
Burner Orifice Injector
Burner Retainer Spring
Burner
8
9
10
11
12
13
14
15
16
17
18
Control Valve
Bracket
Screw
Piezo Ignitor
Pilot Tube
Ignitor Cable
ODS Pilot
Screw, Hex Head (#8-18 x .38)
PARTS AVAILABLE — NOT SHOWN
100563-01
101054-01
100565-01
101137-04
100563-01
101054-01
100565-01
101137-04
Warning Plate
1
1
1
1
Lighting Instructions Plate
Warning Plate Fastener
Hardware Kit
** Not a field replaceable part.
111487-01D
Download from Www.Somanuals.com. All Manuals Search And Download.
21
ILLUSTRATED PARTS BREAKDOWN
STOVE BODY MODELS
CSB SERIES, CSPB SERIES AND CSPI SERIES
9
1
7
7
4
10
5
6
6
6
7
6
6
8
7
2
11
7
3
22
Download from Www.Somanuals.com. All Manuals Search And Download.
111487-01D
PARTS LIST
This list contains replaceable parts used in your stove. For replacement parts see Replacement Parts
on page 19 of this manual.
PART NUMBER
KEY
NO.
CSB Series
(Black)
CSPB Series
(Porcelain Black) (PorcelainIvory) DESCRIPTION
CSPI Series
QTY.
1
1
111698-07
111698-11
111698-08
111698-12
111698-09
111698-13
Top Grate - Center
Bottom Door
2
1
3
111531-01CK 111531-01CK 111531-01CK Stove Dropped Pan (Black Only)
1
4
111698-14
111698-17
111698-20
111764-01
111533-01
111698-15
111698-18
111698-21
111764-01
111533-01
111698-16
111698-19
111698-22
111764-01
111533-01
Left Stove Door
Right Stove Door
Stove Leg
1
5
1
6
4
7
Hardware Kit
Screen Rod
1
8
1
9
111532-01CK 111532-01CK 111532-01CK Stove Back Panel (Black Only)
1
10
11
111698-23
103297-04
111698-23
103297-04
111698-23
103297-04
Door Knob
Screen
1
1
PARTS AVAILABLE — NOT SHOWN
104108-08
———
———
Touch-up Spray Paint
12 oz Can, Black
1
* Included In Hardware Kit
PARTS CENTRALS
These Parts Centrals are privately owned businesses. They have agreed to support our customerʼs needs
by providing original replacement parts and accessories
Tool & Equipment Company
5 Manila Ave.
Hamden, CT 06514-0322
1-800-397-7553
203-248-7553
Master Parts Dist.
1251 Mound Ave NW
Grand Rapids, MI 49504-2672
616-791-0505
1-800-446-1446
Fax: 616-791-8270
Laporte’s Parts & Service
2444 N. 5th Street
Hartsville, SC 29550-7704
843-332-0191
Parts Department
Portable Heater Parts
342 N. County Rd. 400 East
Valparaiso, IN 46383-9704
All States
219-462-7441
1-888-619-7060
Cans Unlimited, Inc.
P.O. Box 645
Taylor, SC 29687-0013
All States
803-879-3009
Washer Equipment Co.
1715 Main Street
Kansas City, MO 64108-2195
KS, MO, AR
816-842-3911
1-800-845-5301
East Coast Energy Products
707 Broadway
FBD
1349 Adams Street
Bowling Green, KY 42103-3414
270-846-1199
W. Long Branch, NJ 07764-1542
732-870-8809
1-800-755-8809
1-800-654-8534
Fax: 1-800-846-0090
21st Century
2950 Fretz Valley Road
Perkasie, PA 18944-4034
215-795-0400
800-325-4828
111487-01D
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our
standard written warranty. We make no other warranty, expressed or implied.
LIMITED WARRANTY
VENT-FREE PROPANE/LP GAS OR NATURAL GAS
LOG HEATERS AND CAST IRON STOVE CHASSIS
DESA Heating Products warrants this product to be free from defects in materials and components for two (2)
years from the date of first purchase, provided that the product has been properly installed, operated and maintained
in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled
check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers only the cost of part(s) required
to restore this heater to proper operating condition. Warranty part(s) MUST be obtained through authorized dealers
of this product and/or DESA Heating Products who will provide original factory replacement parts. Failure to use
original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in
accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear or parts
that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by
improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to
repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE
OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED
WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUD-
ING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO TWO
(2) YEARS FROM THE DATE OF FIRST PURCHASE; AND DESA HEATING PRODUCTSʼ LIABILITY IS
HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA HEATING PRODUCTS
SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCI-
DENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of
incidental or consequential damages, so the above limitation on implied warranties or exclusion or limitation on
damages may not apply to you.
This warranty gives you specific legal rights and you may also have other rights that vary from state to state.
For information about this warranty write:
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
111487-01
Rev. D
09/04
111487 01
NOT A UPC
Download from Www.Somanuals.com. All Manuals Search And Download.
|