Desa Stove S39PT User Manual

VENT-FREE PROPANE/LP GAS FREESTANDING

PEDESTAL STOVE SYSTEM

OWNER’S OPERATION AND INSTALLATION MANUAL

S39PT

20,000 to 39,000 Btu/Hr

Thermostatically-

I ^P

Controlled

WARNING:Improperinstallation,

adjustment, alteration, service,

ormaintenancecancauseinjury

orpropertydamage.Refertothis

manual for correct installation

andoperationalprocedures.For

assistance or additional infor-

mation consult a qualified in-

staller, service agency, or the

gas supplier.

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result caus-

ing property damage, personal injury, or loss of life.

— Donotstoreorusegasolineorotherflammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

Do not touch any electrical switch; do not

use any phone in your building.

Immediately call your gas supplier from a

neighbor’sphone.Followthegassupplier’s

instructions.

WARNING: This is an unvented

gas-firedheater.Itusesair(oxy-

gen) from the room in which it is

installed. Provisions for ad-

equate combustion and ventila-

tion air must be provided. Refer

to Air for Combustion and Ven-

tilation section on page 4 of this

manual.

•

If you cannot reach your gas supplier, call

the fire department.

— Installation and service must be performed by

a qualified installer, service agency, or the gas

supplier.

This appliance may be installed in an aftermarket*, permanently located, manufactured

(mobile) home, where not prohibited by local codes.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

SAFETY

LOCAL CODES

UNPACKING

Install and use heater with care. Follow all 1. Remove top inner pack.

INFORMATION

local codes. In the absence of local codes, use

the latest edition of The National Fuel Gas

Code, ANSI Z223.1/NFPA 54*.

2. Tilt carton so that stove is upright.

3. Remove protective side packaging.

4. Slide stove out of carton.

Continued

16. Do not operate heater if any log is bro-

ken. Do not operate heater if a log is

chipped (dime-sized or larger).

*Available from:

5. Remove protective plastic wrap.

American National Standards Institute, Inc.

1430 Broadway

17. To prevent performance problems, do

not use propane/LP fuel tank of less

than 100 lbs. capacity.

6. Remove screen by lifting and then pull-

ing forward.

New York, NY 10018

7. Remove log set by cutting plastic ties.

8. Carefully unwrap log.

National Fire Protection Association, Inc.

Batterymarch Park

18. Provide adequate clearances around air

openings.

9. Check for any shipping damage. If

stove or log is damaged, promptly in-

form dealer where you bought stove.

Quincy, MA 02269

This heater is designed for vent-free opera-

tion. State and local codes in some areas

prohibit the use of vent-free heaters.

PRODUCT

FEATURES

SAFETY PILOT

PRODUCT

IDENTIFICATION

ThisheaterhasapilotwithanOxygenDeple-

tion Sensing (ODS) safety shutoff system.

The ODS is a required feature for vent-free

roomheaters. TheODSshutsofftheheaterif

there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system

requires no matches, batteries, or other

sources to light heater.

Screen

Stove

Cabinet

Logs

L I ^P

Heater Controls

(Inside Door)

Figure 1 - Vent-Free Propane/LP Gas Stove

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

Confined and Unconfined Space

PROVIDING ADEQUATE

VENTILATION

AIR FOR

The National Fuel Gas Code, ANSI Z223.1/

NFPA 54 defines a confined space as a

space whose volume is less than 50 cubic

feet per 1,000 Btu per hour (4.8 m³per kw)

of the aggregate input rating of all appli-

ances installed in that space and an

unconfining space as a space whose volume

is not less than 50 cubic feet per 1,000 Btu

per hour (4.8 m³per kw) of the aggregate

inputratingofallappliancesinstalledinthat

space. Rooms communicating directly with

the space in which the appliances are in-

stalled*, through openings not furnished

with doors, are considered a part of the

unconfined space.

COMBUSTION AND

VENTILATION

The following are excerpts from National

Fuel Gas Code ANSI Z223.1/NFPA 54, Sec-

tion5.3, AirforCombustionandVentilation.

WARNING: This heater shall

notbeinstalledinaconfinedspace

or unusually tight construction

unless provisions are provided

foradequatecombustionandven-

tilation air. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

All spaces in homes fall into one of the three

following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will

help you classify your space and provide

adequate ventilation.

Today’s homes are built more energy effi-

cient than ever. New materials, increased

insulation, and new construction methods

help reduce heat loss in homes. Home

owners weather strip and caulk around

windows and doors to keep the cold air out

andthewarmairin.Duringheatingmonths,

home owners want their homes as airtight

as possible.

Unusually Tight Construction

*Adjoiningroomsarecommunicatingonly

iftherearedoorlesspassagewaysorventila-

tion grills between them.

The air that leaks around doors and win-

dows may provide enough fresh air for

combustion and ventilation. However, in

buildings of unusually tight construction,

you must provide additional fresh air.

Unusually tight construction is de-

fined as construction where:

a. walls and ceilings exposed to the

outside atmosphere have a con-

tinuous water vapor retarder with

a rating of one perm (6 x 10^-11kg

per pa-sec-m²) or less with open-

ings gasketed or sealed and

While it is good to make your home energy

efficient,yourhomeneedstobreathe.Fresh

air must enter your home. All fuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

Exhaust fans, heaters, clothes dryers, and

fuel burning appliances draw air from the

house to operate. You must provide ad-

equate fresh air for these appliances. This

will insure proper venting of vented fuel-

burning appliances.

b. weather stripping has been

added on openable windows and

doors and

c. caulking or sealants are applied

to areas such as joints around

window and door frames, be-

tween sole plates and floors, be-

tween wall-ceiling joints, be-

tween wall panels, at penetra-

tions for plumbing, electrical, and

gas lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See Ventilation Air

From Outdoors, page 6.

If your home does not meet all of the

three criteria above, proceed to Deter-

mining Fresh-Air Flow For Heater

Location, page 5.

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space:Includestheroominwhichyouwillinstallheaterplusanyadjoiningroomswithdoorlesspassagewaysorventilationgrillsbetween

the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = ____________________ cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of

the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

_________________ (volume of space) x 20 = (Maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 = 51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater

Gas water heater*

Gas furnace

_________________Btu/Hr

Example:

Gas water heater

30,000

39,000

69,000

Btu/Hr

Vent-free heater +

Vented gas heater

Gas heater logs

Total

Other gas appliances* +

Total

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_________________ Btu/Hr (maximum the space can support)

_________________ Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space can support)

69,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space cansupport.

You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoining

room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no

additional fresh air ventilation.

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space

or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of

themethodsdescribedintheNationalFuelGasCode,ANSIZ223.1/NFPA54,Section5.3orapplicablelocalcodes.

Continued

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

AIR FOR

12"

COMBUSTION AND

VENTILATION

Ventilation

Continued

Ventilation Grills

Into Adjoining Room,

Option 2

Grills

Into Adjoining

Room,

VENTILATION AIR

Remove

Door into

Adjoining

Room,

Option

Option 1

Ventilation Air From Inside

Building

Thisfreshairwouldcomefromanadjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(see options 1 and 2, Figure 2). You can also

remove door into adjoining room (see op-

tion 3, Figure 2). Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

12"

Figure 2 - Ventilation Air from Inside Building

Ventilation Air From Outdoors

Ventilated

Provide extra fresh air by using ventilation

grills or ducts. You must provide two per-

manent openings: one within 12" of the

ceiling and one within 12" of the floor.

Connect these items directly to the outdoors

orspacesopentotheoutdoors.Thesespaces

include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/

NFPA 54, Section 5.3, Air for Combustion

and Ventilation for required size of ventila-

tion grills or ducts.

Outlet

Attic

Air

Outlet

Air

To Attic

Crawl

Space

IMPORTANT: Do not provide openings

for inlet or outlet air into attic if attic has

a thermostat-controlled power vent.

Heated air entering the attic will activate

the power vent.

Inlet

Air

Ventilated

Crawl Space

Inlet Air

Figure 3 - Ventilation Air from Outdoors

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

IMPORTANT:Vent-freeheatersaddmois- Carefullyfollowtheinstructionsbelow.This

ture to the air. Although this is beneficial, stove is a freestanding unit designed to set

installing heater in rooms without enough directly on the floor. IMPORTANT: You

ventilation air may cause mildew to form must maintain minimum wall and ceiling

from too much moisture. See Air for Com- clearances during installation. The mini-

bustion and Ventilation, pages 4 through 6. mum clearances are shown in Figure 4.

INSTALLATION

NOTICE: This heater is intended

foruseassupplementalheat.Use

this heater along with your pri-

mary heating system. Do not in-

stall this heater as your primary

heat source. If you have a central

heating system, you may run

system’scirculatingblowerwhile

using heater. This will help circu-

late the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

Measure from outermost point of stove top.

CHECK GAS TYPE

Minimum Wall and Ceiling

Clearances (see Figure 4)

A. Clearances from outermost point of

stove top to any combustible side wall

should not be less than 12 inches.

Useonlypropane/LPgas.Ifyourgassupply

is not propane/LP gas, do not install heater.

Call dealer where you bought heater for

proper type heater.

CLEARANCES TO

COMBUSTIBLES

(Vent-Free Operation Only)

B. Clearances from outermost point of

stove top to any combustible back wall

should not be less than 6 inches (In-

cludes corner installations).

WARNING: A qualified ser-

vice person must install heater.

Follow all local codes.

C. Clearances from the stove top to the

ceiling should not be less than 48

inches.

WARNING:Maintainthemini-

mum clearances. If you can, pro-

vide greater clearances from

floor, ceiling, and adjoining side

and back walls.

WARNING: Never install the

heater

Ceiling

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objectsarelessthan42inches

from the front, top, or sides of

the heater

Front View

48"

Minimum

12"

Side Wall

12"

Side Wall

Minimum

• in high traffic areas

• in windy or drafty areas

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as to-

bacco smoke, aromatic candles,

cleaning fluids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls.

Top View

Back Wall

Minimum

Side View

Ceiling

Minimum

Side Wall

Corner

Side Wall

48"

Minimum

Wall

Back Wall

Minimum

Front of

Stove Unit

Wall

Minimum

Floor

Figure 4 - Minimum Clearance to Walls and Ceiling

Continued

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

Theinstallermustsupplyanexternalregulator.

The external regulator will reduce incoming

gas pressure. You must reduce incoming gas

pressure to between 11 and 14 inches of water.

If you do not reduce incoming gas pressure,

heater regulator damage could occur. Install

external regulator with the vent pointing down

as shown in Figure 6. Pointing the vent down

protects it from freezing rain or sleet.

IMPORTANT: Install equipment shutoff

valve in an accessible location. The equip-

ment shutoff valve is for turning on or

shutting off the gas to the appliance.

INSTALLATION

Continued

CONNECTING TO GAS

SUPPLY

Apply pipe joint sealant lightly to male

threads. This will prevent excess sealant

from going into pipe. Excess sealant in pipe

could result in clogged heater valves.

WARNING: A qualified service

personmustconnectheatertogas

supply. Follow all local codes.

CAUTION:Usepipejointseal-

ant that is resistant to liquid pe-

troleum (LP) gas.

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

yourlocalcodes. Usepipeof1/2"

diameter or greater to allow

proper gas volume to heater. If

pipe is too small, undue loss of

pressure will occur.

CAUTION: Never connect

heater directly to the propane/LP

supply. This heater requires an ex-

ternal regulator (not supplied). In-

stalltheexternalregulatorbetween

the heater and propane/LP supply.

We recommend that you install a sediment

trap in supply line as shown in Figure 7.

Locate sediment trap where it is within

reach for cleaning. Install in piping system

betweenfuelsupplyandheater.Locatesedi-

ment trap where trapped matter is not likely

to freeze. A sediment trap traps moisture

and contaminants. This keeps them from

going into heater controls. If sediment trap

is not installed or is installed wrong, heater

may not run properly.

Installation Items Needed

Beforeinstallingheater,makesureyouhave

the items listed below.

Installation must include an equipment

shutoff valve, union, and plugged 1/8" NPT

tap. Locate NPT tap within reach for test

gauge hook up. NPT tap must be upstream

from heater (see Figure 7).

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• sediment trap

CAUTION: Avoid damage to

regulator.Holdgasregulatorwith

wrenchwhenconnectingittogas

piping and/or fittings.

Propane/LP

Supply Tank

External

Regulator

• tee joint

• pipe wrench

An CSA design-certified equipment

shutoff valve with 1/8" NPT tap is an ac-

ceptable alternative to test gauge connec-

tion. Purchase the optional CSA design-

certifiedequipmentshutoffvalvefromyour

dealer. See Accessories, page 24.

Vent

Pointing

Down

Figure 6 - External Regulator With Vent

Pointing Down

Back View

From External

Regulator (11"

W.C.** to 14"

W.C. Pressure)

CSA Design-Certified

Equipment Shutoff Valve

With 1/8" NPT Tap*

Approved

Side View

Flexible Gas

Hose (if allowed

by local codes)

Front

Stove

Unit

Tee

Joint

Sediment

Trap

Gas Regulator

Inlet Connection

3" Minimum

Pipe

Nipple

Gas

Regulator

of Heater

Cap

Figure 5 - Gas Regulator Location and

Gas Line Access Into Stove Cabinet

Figure 7 - Gas Connection

* Purchase the optional CSA design-certified equipment shutoff valve from your dealer.

See Accessories, page 24.

**Minimum inlet pressure for purpose of input adjustment.

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

Pressure Testing Heater Gas

Connections

1. Open equipment shutoff valve (see Fig-

ure 8).

INSTALLATION

Continued

1. Close equipment shutoff valve (see Fig-

ure 8).

CHECKING GAS

CONNECTIONS

2. Pressurize supply piping system by either

using compressed air or opening propane/

LP supply tank valve.

2. Open propane/LP supply tank valve.

3. Make sure control knob of heater is in

the OFF position.

WARNING: Test all gas pip-

ing and connections for leaks

after installing or servicing. Cor-

rect all leaks at once.

3. Check all joints from gas meter to

equipment shutoff valve (see Figure 9).

Apply a noncorrosive leak detection

fluid to all joints. Bubbles forming

show a leak.

4. Check all joints from equipment shutoff

valve to control valve (see Figure 9).

Apply a noncorrosive leak detection

fluid to all joints. Bubbles forming

show a leak.

WARNING:Neveruseanopen

flame to check for a leak. Apply a

noncorrosiveleakdetectionfluid

toalljoints.Bubblesformingshow

a leak. Correct all leaks at once.

4. Correct all leaks at once.

5. Correct all leaks at once.

Open

POSIT

6. Light heater (see Operating Heater,

pages 13 and 14). Check all other in-

ternal joints for leaks.

Equipment

Shutoff

Valve

7. Turn off heater (see To Turn Off Gas to

Appliance, page 14).

Closed

POS

CAUTION: Make sure exter-

nal regulator has been installed

between propane/LP supply and

heater.SeeguidelinesunderCon-

necting to Gas Supply, page 8.

Figure 8- Equipment Shutoff Valve

Equipment Shutoff Valve

Propane/LP

Supply Tank

Pressure Testing Gas Supply

Piping System

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

1. Disconnect heater with its appliance

main gas valve (control valve) and

equipment shutoff valve from gas sup-

ply piping system. Pressures in excess

of 1/2 psig will damage heater regulator.

2. Cap off open end of gas pipe where

equipment shutoff valve was connected.

3. Pressurize supply piping system by ei-

ther using compressed air or opening

propane/LP supply tank valve.

Control Valve Location

Figure 9 - Checking Gas Joints

4. Check all joints of gas supply piping

system. Apply a noncorrosive leak de-

tection fluid to all joints. Bubbles form-

ing show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment

shutoff valve to gas supply. Check re-

connected fittings for leaks.

Continued

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

8. Attach the two mounting brackets to

INSTALLING OPTIONAL

BLOWER ACCESSORY

GA3750

INSTALLATION

blower housing using four screws pro-

vided in blower kit (2 for each bracket)

(see Figure 15). Tighten screws se-

curely. Place blower assembly tempo-

rarily on top of firebox.

Continued

INSTALLING LOGS

Tools required: Phillips screwdriver

WARNING: Failure to position

thepartsinaccordancewiththese

diagrams or failure to use only

parts specifically approved with

this heater may result in property

damage or personal injury.

NOTICE:Shutoffgasheaterduring

the following blower installation.

9. Working from the rear of the stove,

place entire power cord, including

speed control housing, in lower control

compartment.

1. Remove 2 screws from rear tabs on top

trim. Pull trim forward to remove (see

Figure 12).

10. Route ends of 3-wire power cord up from

the lower control compartment through

the plastic bushing, then up to the upper

cavity of stove (see Figure 16, page 11).

2. Remove top panel of stove by remov-

ing three screws from under top lip on

each side of stove (see Figure 12).

CAUTION:Afterinstallationand

periodicallythereafter,checktoen-

surethatnoflamecomesincontact

with any log. With the heater set to

High,checktoseeifflamescontact

any log. If so, reposition logs ac-

cording to the log installation in-

structions in this manual. Flames

contacting logs will create soot.

11. Attach the terminal ends of the white

and black power cord wires to the ter-

minals on the blower motor (see Fig-

ure 13). Push firmly.

3. Facing front of stove, carefully slide top

panel forward until it is completely re-

moved from stove (see Figure 12).

4. Install one plastic bushing provided in

blower kit into the 1 ¹/2" hole in the left

rear of firebox floor. Access hole

through the rectangular opening in the

rear panel (see Figure 13).

12. Attach the terminal end of the green

power cord wire to the front tab of the

blower housing using screw provided

(see Figure 13).

Itisveryimportanttoinstallthelogsexactly

as instructed. Do not modify logs. Only use

logs supplied with heater.

5. Disconnect power cord wires from blower

motor (if connected) (see Figure 14).

White

Powercord

Wire

6. Disconnect green ground wire from

blower housing (if connected) by re-

moving screw holding wire terminal

(see Figure 14).

Place one-piece log set on grate to fit as

illustrated in Figure 10. Make sure log sits

flat on firebox floor (see Figure 10).

IMPORTANT:Makesurelogdoesnotcover

any burner ports (see Figure 11).

Screw

Green

Ground Wire

7. Remove the two blower mounting

brackets from the rear panel by remov-

ing two screws each (see Figure 15).

Black Powercord Wire

Figure 14 - Removing Wires from Blower

Screws

One Piece

Log Set

Screws

Top Panel

Blower

Bracket

Top

Trim

I ^P

Blower

Screws

Firebox Floor

Figure 10 - Installing One-Piece Log Set

Screws

Figure 12 - Removing Stove Top Panel

One Piece Log Set

Burner Ports

Firebox Top

Figure 15 - Removing Blower Brackets

from Stove and Attaching to Blower

Figure 11 - Installing One-Piece Log set

(Top View)

Figure 13 - Installing Bushing

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

INSTALLING OPTIONAL

BLOWER ACCESSORY

GA3650TA

INSTALLATION

WARNING: ELECTRICAL

Continued

GROUNDING INSTRUCTIONS

This appliance is equipped with a

three-prong (grounding) plug for

your protection against shock

hazard and should be plugged

directly into a properly grounded

three-prong receptacle.

13. Using the four screws previously re-

moved, mount blower assembly to

stove by reattaching blower brackets to

rear panel (see Figure 15, page 10).

Tighten screws securely.

Tools required: Phillips screwdriver

NOTICE:Shutoffgasheaterduring

the following blower installation.

14. Install plastic control knob onto output

shaft of speed control housing (see Fig-

ure 16). Place speed control housing

just inside control compartment door

in front of stove (see Figure 17).

1. Remove 2 screws from rear tabs on top

trim. Pull trim forward to remove (see

Figure 12, page 10).

20. Using speed control knob, turn blower

on and check for operation.

21. All remaining parts from blower kit

may be discarded.

2. Remove three screws from under top

lip on each side of stove to remove top

panel (see Figure 12, page 10).

15. Using two screws provided in blower

kit, mount blower speed control hous-

ing to mounting tab in left side of lower

control compartment (see Figure 17).

3. Facing front of stove, carefully slide top

panel forward until it is completely re-

moved from stove (see Figure 12, page

10).

16. Check to make sure that the power cord is

completelyclearofblowerwheelandthere

are no foreign objects in blower wheel.

6. Install one plastic bushing provided in

blower kit into the 1 ¹/2" hole in the left

rear of firebox floor. Access hole

through the rectangular opening in the

rear panel (see Figure 13, page 10).

17. Carefully replace stove top panel.Align

holes and replace six screws removed

in step 1, page 10. Slide top trim onto

top panel. Attach with 2 screws re-

moved in step 1, page 10.

Blower Speed

Control Housing

Figure17-InstallingBlowerControlHousing

4. Disconnect power cord wires from blower

motor (if connected) (see Figure 14, page

10).

18. Peel off the backing paper and stick the

supplied wiring diagram decal on the

stove floor as shown in Figure 16.

5. Disconnect green ground wire from

blower housing (if connected) by re-

moving screw holding wire terminal

(see Figure 14, page 10).

19. Plugpowercordintoaconvenient3-prong

grounded wall receptacle near the stove.

7. Remove the two blower mounting

brackets from the rear panel by remov-

ing two screws each (see Figure 15,

page 10).

8. Attach the two mounting brackets to

blower housing using four screws pro-

vided in blower kit (2 for each bracket)

(see Figure 15, page 10). Tighten

screws securely. Place blower assem-

bly temporarily on top of firebox.

WARNING: Never attempt to service heater while it

is plugged in, operating, or hot. Burns and electrical

shock could result. Only a qualified service person

should service or repair heater.

If any of the original wire as supplied with the appliance must be

replaced, it must be replaced with 105°C wire or it’s equivalent.

9. If screen is installed, carefully lift

slightly and pull forward to remove.

Power

Cord

WARNING: Label all wires prior to disconnection

when servicing controls. Wiring errors can cause im-

proper and dangerous operation. Verify proper opera-

tion after servicing.

10. If logs are installed, carefully remove

and set aside.

Variable

Fan Switch

Off

Wiring

Diagram

Decal

110/115

V.A.C.

Blower

Motor

Black

Green

White

Black

White

Speed Control

Housing

Control

Knob

120 Vac. 60 Hz. . 78 Amps

DESA International, Bowling Green, KY

101584-05

Continued

Figure 16 - Routing Power Cord

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

16. Route ends of 3-wire power cord up from 18. Connect the black wire from speed con-

INSTALLATION

the lower control compartment through

the plastic bushing, then up to the upper

cavity of stove (see Figure 21).

trol to blue wire on switch/cover assem-

bly (see Figure 21).

Continued

19. Connect red wire from switch/cover

assembly to remaining terminal on

blower motor (see Figure 21). Push

firmly.

11. Remove three screws and cover plate

from center of firebox back panel.

Keep screws but discard cover plate

(see Figure 18).

17. Connect white wire from speed control

to either terminal on blower motor (see

Figure 21). Push firmly.

20. Attach green wire from speed control

to front tab of blower housing using

screw provided (see Figure 21). Tighten

securely.

12. Locate thermostatic switch/cover plate

assembly and wire harness supplied

with blower. Attach wire harness ter-

minals to terminals on thermostatic

switch. Push firmly. Make sure the bot-

tom hole of cover is on the opposite side

from the wire harness (see Figure 19).

Thermostatic

Switch

Mounted to

Cover

Wire Harness

Hole in Firebox

Back Panel

21. Using the four screws previously re-

moved, mount blower assembly to

stove by reattaching blower brackets to

rear panel (see Figure 15, page 10).

Tighten screws securely.

13. Feed terminal ends of wire harness into

the hole in firebox back panel from

front of firebox. Pull the ends of the

harness to the top of firebox near

blower (see Figure 20).

22. Install plastic control knob onto output

shaft of speed control housing (see Fig-

ure 21). Place speed control housing just

inside control compartment door in front

of stove (see Figure 17, page 11).

14. Align holes in the switch/cover assem-

bly with holes in firebox back panel.

Using 3 screws from step 11, attach

assembly to firebox back panel. Tighten

screws firmly (see Figure 20).

23. Using two screws provided in blower

kit, mount blower speed control hous-

ing to mounting tab in left side of lower

control compartment (see Figure 17,

page 11).

Wire Harness

15. Working from the rear of the stove,

place entire power cord, including

speed control housing, in lower control

compartment (see Figure 21).

Screws

Figure 20 - Assembling Thermostatic

Switch and Cover to Firebox Back Panel

24. Check to make sure that the power cord is

completelyclearofblowerwheelandthere

are no foreign objects in blower wheel.

White Speed

Green

Ground

Wire

Cover

Plate

25. Carefully replace stove top panel.Align

holes and replace six screws removed

in step 1, page 10. Slide top trim over

tip panel.Attach with 2 screws removed

in step 1, page 11.

Control Wire

Black

Speed

Control

Wire

Blower

Screws

WARNING: Never attempt to service heater while it

is plugged in, operating, or hot. Burns and electrical

shock could result. Only a qualified service person

should service or repair heater.

Ground

Wire Screw

Firebox Back Panel

Blue

Switch

Wire

Red

Switch

Wire

Figure 18 - Removing Cover Plate

If any of the original wire as supplied with the appliance must be

replaced, it must be replaced with 105°C wire or it’s equivalent.

Power

Cord

Lower Hole

WARNING: Label all wires prior to disconnection

when servicing controls. Wiring errors can cause im-

proper and dangerous operation. Verify proper opera-

tion after servicing.

Thermostatic

Switch

Mounted to

Cover

Variable

Fan Switch

(N.O.)

Fan Switch

Wiring

Diagram

Decal

Off

Black

Blue

Red

110/115

V.A.C.

Black

Green

White

Wire Harness

Blower

Motor

Speed Control

Housing

Control

Knob

120 Vac. 60 Hz. 90 Amps

DESA International, Bowling Green, KY

Figure 19 - Attaching Wire Harness to

ThermostaticSwitchandCoverAssembly

Figure 21 - Connecting Switch, Blower,

and Speed Control Wires

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

LIGHTING

INSTRUCTIONS

INSTALLATION

OPERATING

HEATER

Continued

26. Peel off the backing paper and stick the

supplied wiring diagram decal on the

stove floor as shown in Figure 19.

NOTICE: During initial operation

FOR YOUR SAFETY

of new heater, burning logs will

give off a paper-burning smell.

Orange flame will also be present.

Open a window to vent smell. This

will only last a few hours.

READ BEFORE

LIGHTING

27. Plugpowercordintoaconvenient3-prong

grounded wall receptacle near the stove.

WARNING: If you do not fol-

low these instructions exactly, a

fireorexplosionmayresultcaus-

ing property damage, personal

injury or loss of life.

WARNING: ELECTRICAL

GROUNDING INSTRUCTIONS

Thisapplianceisequippedwitha

three-prong (grounding) plug for

your protection against shock

hazard and should be plugged

directly into a properly grounded

three-prong receptacle.

1. STOP! Read the safety information,

column 2.

2. Make sure equipment shutoff valve

is fully open.

A. This appliance has a pilot which must

be lighted by hand. When lighting the

pilot, follow these instructions exactly.

3. Turn control knob clockwise

to the OFF position.

Clockwise

4. Wait five (5) minutes to clear out any

gas. Then smell for gas, including

near the floor. If you smell gas,

STOP! Follow “B” in the safety in-

formation, column 2. If you don’t

smell gas, go to the next step.

B. BEFORE LIGHTING smell all

around the appliance area for gas. Be

sure to smell next to the floor because

some gas is heavier than air and will

settle on the floor.

28. Using speed control knob, turn blower

on and check for operation.

29. Install logs (see Installing Logs, page 10).

30. Install screen assembly by aligning

keyhole slots in screen assembly and

shoulder screws on stove. Push back

and down to secure.

WHATTO DO IFYOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

5. Turn control knob counterclockwise

to the PILOT position.

Press in control knob for five (5) sec-

onds (see Figure 22).

C-clockwise

31. All remaining parts from blower kit

may be discarded.

Note: You may be running this

heater for the first time after hook-

ing up to gas supply. If so, the con-

trol knob may need to be pressed in

for 30 seconds or less. This will allow

air to bleed from the gas system.

Note: If any of the origianl wire, as supplied

with the appliance, must be replaced, it must

bereplacedwith105°Cwireorit’sequivalent.

• If you cannot reach your gas sup-

plier, call the fire department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn 6. With control knob pressed in, press

by hand, don’t try to repair it, call a

qualified service technician or gas

supplier. Force or attempted repair

may result in a fire or explosion.

and release ignitor button. This will

light pilot. The pilot is attached to the

front burner. If needed, keep press-

ing ignitor button until pilot lights.

D. Do not use this appliance if any part

has been under water. Immediately call

a qualified service technician to inspect

the appliance and to replace any part

of the control system and any gas con-

trol which has been under water.

Note: If pilot does not stay lit, con-

tact a qualified service person or gas

supplier for repairs. Until repairs are

made, light pilot with match. To light

pilot with match, see Manual Light-

ing Procedure, page 14.

Control Knob

Ignitor Button

Figure 22 - Control Knob and Ignitor

Button Location

Continued

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

Note: Selecting the Hi setting with the

control knob will cause the burners to

OPERATING

INSPECTING

HEATER

remainfullyon,withoutmodulatingdown BURNERS

in most cases.

Continued

7. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob.

Check pilot flame pattern and burner flame

patterns often.

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 5 under Light-

ing Instructions, page 13.

PILOT FLAME PATTERN

• Ifcontrolknobdoesnotpopoutwhen

released, contact a qualified service

person or gas supplier for repairs.

Figure 24 shows a correct pilot flame pat-

tern.Figure25showsanincorrectpilotflame

pattern.Theincorrectpilotflameisnottouch-

ing the thermocouple. This will cause the

thermocouple to cool. When the thermo-

couple cools, the heater will shut down.

2. Depress control knob and light pilot

with match.

Note: If pilot goes out, repeat steps

3 through 7, pages 13 and 14. This

heater has a safety interlock system.

Wait one (1) minute for system to

reset before lighting pilot again.

3. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob. Now

follow step 8 in column 1.

If pilot flame pattern is incorrect, as shown

in Figure 25

8. Turn control knob counterclockwise

• turn heater off (see To Turn Off Gas to

Appliance)

C-clockwise

to desired heating level. The

OPERATING

OPTIONAL BLOWER

ACCESSORY

burners should light. Set control knob

to any heat level between HI and LO.

• see Troubleshooting, pages 16 through 18

Pilot Burner

Thermocouple

Light your gas appliance with the blower

off. Turn the blower on to deliver heated

air at the top louvers. The blower fea-

tures a variable control which allows you

to select the speed you desire.

Thermocouple

Figure 23 - Pilot

IfusingtheGA3650TABlowerAccessory:

In the ON position, the blower will start

when the thermostat senses a sufficient

increaseinfireboxtemperature(approxi-

mately 10 to 20 minutes depending on

heat setting). Note: Your gas stove and

thermostat blower will not turn on and

off at the same time. The stove may run

for several minutes before the blower

turns on. After the heater modulates to

the pilot position, the blower will con-

tinue to run. The blower will shut off

after the firebox temperature decreases.

Figure 24 - Correct Pilot Flame Pattern

CAUTION:Donottrytoadjust

heatinglevelsbyusingtheequip-

ment shutoff valve.

Pilot Burner

Thermocouple

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise

the OFF position.

Clockwise

Figure 25 - Incorrect Pilot Flame Pattern

Shutting Off Burners Only (pilot

stays lit)

Note: It is safe to operate stove with

blower turned off. However, the blower

helpsdistributeheatedairfromthestove.

Turn control knob clockwise

the PILOT position.

Clockwise

Note: Periodically check the louvers of

the firebox and remove any dust, dirt, or

other obstructions.

THERMOSTAT CONTROL

OPERATION

The thermostat control knob can be set to

any comfort level between Hi and Lo. The

thermostatwillgraduallymodulatetheheat

output and flame height from higher to

lower settings, or pilot, in order to maintain

the comfort level you select. The ideal com-

fort setting will vary by household depend-

ing upon the amount of space to be heated,

the output of the central heating system, etc.

Continued

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

CLEANING BURNER

INJECTOR HOLDER AND

PILOT AIR INLET HOLE

Burner

Injector

INSPECTING

Tube

Holder

BURNERS

Continued

The primary air inlet holes allow the proper

amount of air to mix with the gas. This pro-

videsacleanburningflame. Keeptheseholes

clear of dust, dirt, lint, and pet hair. Clean

these air inlet holes prior to each heating

season.Blockedairholeswillcreatesoot.We

recommendthatyoucleantheuniteverythree

months during operation and have heater in-

spected yearly by a qualified service person.

BURNER FLAME PATTERN

Primary Air

Inlet Holes

Figure 26 shows a correct burner flame pat-

tern. Figure 27 shows an incorrect burner

flame pattern. If burner flame pattern is

incorrect,

Figure 28 - Injector Holder On Outlet

Burner Tube

Ports/Slots

• turn heater off (see To Turn Off Gas to

Appliance, page 14)

Burner

Tube

• see Troubleshooting, pages 16 through 18

Wealsorecommendthatyoukeeptheburner

tubeandpilotassemblycleanandfreeofdust

and dirt. To clean these parts we recommend

using compressed air no greater than 30 PSI.

Yourlocalcomputerstore,hardwarestore,or

home center may carry compressed air in a

can. You can use a vacuum cleaner in the

blow position. If using compressed air in a

can, please follow the directions on the can.

If you don't follow directions on the can, you

could damage the pilot assembly.

Approx. 3-6" Above

Top of Logs

Pilot

Assembly

Pilot Air

Inlet

Hole

Figure 26 - Correct Flame Pattern with

Control Knob Set to High Flame.

Figure 29 - Pilot Inlet Air Hole

1. Shut off the unit, including the pilot.

Allow the unit to cool for at least thirty

minutes.

More Than 8"

Above Top of Logs

CABINET

Air Passageways

• Use a vacuum cleaner or pressurized air

to clean.

2. Inspect burner, pilot, and primary air

inlet holes on injector holder for dust

and dirt (see Figure 28).

Exterior

3. Blow air through the ports/slots and

holes in the burner.

• Use a soft cloth dampened with a mild

soap and water mixture. Wipe the cabi-

net to remove dust.

4. Check the injector holder located at the

end of the burner tube again. Remove any

large particles of dust, dirt, lint, or pet hair

with a soft cloth or vacuum cleaner nozzle.

LOGS

Figure 27 - Incorrect Flame Pattern with

Control Knob Set to High Flame

• If you remove logs for cleaning, refer to

Installing Logs, page 10, to properly re-

place logs.

• Replace log(s) if broken or chipped

(dime-sized or larger).

5. Blow air into the primary air holes on

the injector holder.

CLEANING AND

MAINTENANCE

6. In case any large clumps of dust have

now been pushed into the burner repeat

steps 3 and 4.

MAIN BURNER

WARNING: Turn off heater

and let cool before cleaning.

Clean the pilot assembly also. A yellow tip

on the pilot flame indicates dust and dirt in

the pilot assembly. There is a small pilot air

inlet hole about two inches from where the

pilot flame comes out of the pilot assembly

(see Figure 29). With the unit off, lightly

blow air through the air inlet hole. You may

blowthroughadrinkingstrawifcompressed

air is not available.

Periodically inspect all burner flame holes

with the heater running. All slotted burner

flame holes should be open with yellow

flame present. All round burner flame holes

should be open with a small blue flame

present. Some burner flame holes may be-

comeblockedbydebrisorrust,withnoflame

present. If so, turn off heater and let cool.

Either remove blockage or replace burner.

Blocked burner flame holes will create soot.

CAUTION: You must keep

control areas, burner, and circu-

lating air passageways of heater

clean. Inspect these areas of

heater before each use. Have

heaterinspectedyearlybyaquali-

fied service person. Heater may

needmorefrequentcleaningdue

to excessive lint from carpeting,

bedding material, pet hair, etc.

Reviewyourvideoincludedwithyourheater

for additional cleaning instructions.

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

TROUBLESHOOTING

Note: For additional help, visit DESA

International’stechnicalservicewebsite

at www.desatech.com.

CAUTION: Never use a wire,

WARNING: Turn off heater

andletcoolbeforeservicing.Only

aqualifiedservicepersonshould

service and repair heater.

needle, or similar object to clean

ODS/pilot.ThiscandamageODS/

pilot unit.

Note:Alltroubleshootingitemsarelistedin

order of operation.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed, there is no

spark at ODS/pilot

1. Ignitor electrode not connected to igni- 1. Reconnect ignitor cable

tor cable

2. Ignitor cable pinched or wet

2. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

3. Tighten nut holding piezo ignitor to base

panel of log set. Nut is located behind

base panel

3. Piezo ignitor nut is loose

4. Broken ignitor cable

4. Replace ignitor cable

5. Bad piezo ignitor

5. Replace piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode positioned wrong

6. Replace piezo ignitor

7. Replace piezo ignitor

When ignitor button is pressed, there is

spark at ODS/pilot but no ignition

1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment

shutoff valve closed

shutoff valve

2. Control knob not in PILOT position

2. Turn control knob to PILOT position

3. Control knob not pressed in while in 3. Press in control knob while in PILOT

PILOT position

position

4. Air in gas lines when installed

4. Continue holding down control knob.

Repeat igniting operation until air is re-

moved

5. Depleted gas supply

6. ODS/pilot is clogged

5. Contact local propane/LP gas company

6. Clean ODS/pilot (see Cleaning and

Maintenance, page 15) or replace ODS/

pilot assembly

7. Gas regulator setting is not correct

1. Control knob not fully pressed in

2. Control knob not pressed in long enough 2. After ODS/pilot lights, keep control

knob pressed in 30 seconds

7. Replace gas control

ODS/pilot lights but flame goes out when

control knob is released

1. Press in control knob fully

3. Equipment shutoff valve not fully open 3. Fully open equipment shutoff valve

4. Pilot flame not touching thermocouple, 4. A) Contact local propane/LP gas company

which allows thermocouple to cool,

causing pilot flame to go out. This prob-

lem could be caused by one or both of

the following:

B) Clean ODS/pilot (see Cleaning and

Maintenance, page 15) or replace ODS/

pilot assembly

A) Low gas pressure

B) Dirty or partially clogged ODS/pilot

5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten 1/4

trol valve

turn more

6. Thermocouple damaged

7. Control valve damaged

6. Replace thermocouple

7. Replace control valve

www.desatech.com

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Burner does not light after ODS/pilot is lit

1. Burner orifice clogged

1. Clean burner (see Cleaning and Mainte-

nance, page 15) or replace burner orifice

2. Contact local propane/LP gas company

2. Inlet gas pressure is too low

3. Burner orifice diameter is too small

3. Replace burner orifice

4. Thermopile leads disconnected or im- 4. Reconnect leads (see wiring diagram)

properly connected

5. Burners will not come on in remote position 5. Replace battery in transmitter and receiver

Delayed ignition burner

1. Manifold pressure is too low

2. Burner orifice clogged

1. Contact local propane/LP gas company

2. Clean burner (see Cleaning and Mainte-

nance, page 15) or replace burner orifice

Burner backfiring during combustion

1. Burner orifice is clogged or damaged

1. Clean burner (see Cleaning and Mainte-

nance, page 15) or replace burner orifice

2. Replace damaged burner

2. Damaged burner

3. Gas regulator defective

3. Replace gas control

Slight smoke or odor during initial operation 1. Not enough air

1. Check burner for dirt and debris. If found,

clean burner (see Cleaning and Mainte-

nance, page 15)

2. Gas regulator defective

2. Replace gas control

3. Residues from manufacturing processes 3. Problem will stop after a few hours of

and logs curing

operation

Moisture/condensation noticed on windows 1. Not enough combustion/ventilation air

1. Refer to Air for Combustion and Ventila-

tion requirements (page 4)

Heater produces a whistling noise when 1. Turning control knob to HI position when 1. Turn control knob to LO position and let

burner is lit

burner is cold

warm up for a minute

2. Air in gas line

2. Operate burner until air is removed from

line. Have gas line checked by local pro-

pane/LP gas company

3. Air passageways on heater blocked

3. Observe minimum installation clearances

(see pages 7 through 9)

4. Dirty or partially clogged burner orifice

4. Clean burner (see Cleaning and Mainte-

nance, page 15) or replace burner orifice

Dark residue on logs or inside of fireplace

1. Improper log placement

1. Properly locate logs (see Installing Logs,

page 10)

2. Drafts or other air currents affecting 2. Eliminate source of drafts around heater

flame pattern

3. Air holes at burner inlet blocked

3. Clean out air holes at burner inlet. Peri-

odically repeat as needed

4. Burner flame holes blocked

4. Remove blockage or replace burner

Whitepowderresidueformingwithinburner 1. When heated, vapors from furniture pol- 1. Turn heater off when using furniture pol-

box or on adjacent walls or furniture

ish, wax, carpet cleaners, etc. turn into

white powder residue

ish, wax, carpet cleaners, or similar

products

Continued

www.desatech.com

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthe

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,

etc., create fumes. These fumes may mix with combustion air and create odors. These odors

will disappear over time.

POSSIBLE CAUSE

OBSERVED PROBLEM

REMEDY

1. Metal expanding while heating or con-

tracting while cooling

Heater produces a clicking/ticking noise

just after burner is lit or shut off

1. This is common with most heaters. If

noise is excessive, contact qualified ser-

vice person

1. Heater burning vapors from paint, hair

spray, glues, cleaners, chemicals, new

carpet, etc. (See IMPORTANT state-

ment above)

Heater produces unwanted odors

1. Open window and ventilate room. Stop

using odor causing products while heater

is running

2. Gas leak. SeeWarning statement at

top of page

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

Heater shuts off in use (ODS operates)

1. Open window and/or door for ventilation

2. Contact local propane/LP gas company

3. Clean ODS/pilot (see Cleaning and

Maintenance, page 15)

1. Gas leak. SeeWarning statement at

top of page

2. Control valve defective

Gas odor even when control knob is in OFF

position

1. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

2. Replace control valve

1. Foreign matter between control valve

and burner

Gas odor during combustion

1. Take apart gas tubing and remove for-

eign matter

2. Gas leak. SeeWarning statement at

top of page

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

1. Excessive line or manifold pressure

2. Dirty primary air holes

Burner flame is excessively large and is

very near or touches the top of firebox

1. Check manifold pressure and correct as

needed

2. Clean burner air holes (see Cleaning and

Maintenance, page15)

www.desatech.com

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

SPECIFICATIONS

PARTS CENTRALS

These Parts Centrals are privately owned businesses. They have agreed to support our

customer’s needs by providing original replacement parts and accessories.

Btu (Variable)

Type Gas

20,000/39,000

Propane/LP Only

Piezo

Ignition

Baltimore Electric

1348 Dixwell Avenue

Hamden, CT 06514-0322

1-800-397-7553

203-248-7553

Parts Department

Tarantin Tank Co.

P.O. Box 6129

Freehold, NJ 07728-6129

908-780-9340

1-800-922-0724

Manifold Pressure

8" W.C.

Inlet Gas Pressure

(in. of water) *

Maximum

Minimum

Dimensions, Inches (H x W x D)

Stove

Carton

Weight, pounds

Stove

14"

11"

www.tarantin.com

31 x 32 x 19 ¹/4

24 x 31 ¹/2 x 35 ¹/4

Portable Heater Parts

342 N. County Rd. 400 East

Valparaiso, IN 46383-9704

All States

219-462-7441

1-800-362-6951

ayton Hardware

P.O. Box 275

North Dayton Station

Dayton, OH 45404-0275

All States

78 lbs.

95 lbs.

Shipping

937-258-3721

OH 1-800-762-3426

* For purposes of input adjustment

[email protected]

Halco Enterprises

208 Carter Drive, Unit 21

West Chester, PA 19382-4500

610-430-7717

1-800-368-0803

www.halcoenterprises.com

FBD

SERVICE HINTS

1349 Adams Street

Bowling Green, KY 42103-3414

270-846-1199

When Gas Pressure Is Too Low

• pilot will not stay lit

1-800-654-8534

Fax: 1-800-846-0090

[email protected]

• burners will have delayed ignition

• heater will not produce specified heat

• propane/LP gas supply may be low

Laporte’s Parts & Service

2444 N. 5th Street

Master Parts Dist.

1251 Mound Ave NW

Grand Rapids, MI 49504-2672

616-791-0505

1-800-446-1446

Fax: 616-791-8270

www.nbmc.com

Hartsville, SC 29550-7704

803-332-0191

Parts Department

You may feel your gas pressure is too low.

If so, contact your local propane/LP gas

supplier.

Cans Unlimited, Inc.

P.O. Box 645

Taylor, SC 29687-0013

All States

803-879-3009

TECHNICAL

SERVICE

You may have further questions about in-

stallation, operation, or troubleshooting. If

so, contact DESA International’s Technical

Service Department at 1-800-DESA LOG

(1-800-337-2564).

Washer Equipment Co.

1715 Main Street

Kansas City, MO 64108-2195

KS, MO, AR

816-842-3911

www.washerparts.com

1-800-845-5301

[email protected]

You can also visit DESA International’s

technical services web site at

www.desatech.com.

East Coast Energy Products

707 Broadway

W. Long Branch, NJ 07764-1542

732-870-8809

1-800-755-8809

www.njplaza.com/ecep

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

ILLUSTRATED

PARTS

BREAKDOWN

S39PT

107435

Download from Www.Somanuals.com. All Manuals Search And Download.

For more information, visit www.desatech.com

OWNER’S MANUAL

This list contains replaceable parts used in your heater. When ordering parts, follow the

instructions listed under Replacement Parts on page 24 of this manual.

PARTS LIST

S39PT

KEY PART

NO.

NUMBER

DESCRIPTION

QTY.

107433-02

104286-01

098249-01

107090-02

102843-01

099056-17

101329-19

102772-01

099387-09

098271-07

101381-01

098867-10

107089-01

Log Set

ODS Pilot (LP)

ODS Nut

Burner Outlet Tube

Burner Clip

Burner Orifice Injector

Gas Control Valve

Burner

Pilot Tube

Ignitor Cable

Piezo Ignitor and Cover

Regulator

Inlet Tube

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

ILLUSTRATED

PARTS

BREAKDOWN

S39PT

107435

Download from Www.Somanuals.com. All Manuals Search And Download.

For more information, visit www.desatech.com

OWNER’S MANUAL

Thislistcontainsreplaceablepartsusedinyourheater. Whenorderingparts, followtheinstructions

listed under Replacement Parts on page 24 of this manual.

PARTS LIST

S39PT

KEY

NO.

PART NO.

DESCRIPTION

QTY.

107085-01CK

107077-01CK

107076-01CK

107075-01CK

107082-01CK

105657-01

107363-01CK

107078-01CJ

107080-01CK

107081-01CJ

107365-01CK

101382-01

107092-01

107093-01

105576-01

101386-02

099230-02

107079-01CJ

102455-12

Top Panel, Stove

Pedestal Stove Assembly

Stove Base

Stove Back Panel

Top Trim

Blower Bracket

Door

Firebox Back Panel

Firebox Floor

Firebox Top

Screen Assembly

Valve Bracket

Brass Trim, Bottom

Brass Trim, Firebox

Knob

Door Hinge

Shoulder Screw

Heat Deflector

Louver, Small

102455-13

Louver, Large

107091-01CK

107084-01CK

101514-01CK

103158-01

107083-01

098304-03

Support, End Louver

Support, Center Louver

Blower Sensor Cover

Magnet Catch

Magnet Bracket

Louver Screw

PARTS AVAILABLE — NOT SHOWN

101054-01

100563-01

104310-12

104108-06

Lighting Instructions Plate

Warning Plate

Information Video

Touch-Up Paint Kit

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE PROPANE/LP PEDESTAL STOVE

CLEANING KIT - CCK

(Not Shown)

REPLACEMENT

PARTS

ACCESSORIES

Purchasetheseheateraccessoriesfromyour

localdealerorPartsCentral(seepage19). If

they cannot supply these accessories call

Your vent-free gas appliance requires regu-

lar cleaning and maintenance to prevent

performance problems. This kit gives you

the tools and instructions to make it easy to

clean all critical areas of your appliance.

Note: Use only original replacement parts.

This will protect your warranty coverage DESA International’s Sales Department at

for parts replaced under warranty.

1-800-458-2472 for referral information.

You can also write to the address listed on

the back page of this manual.

PARTS UNDER WARRANTY

Contact authorized dealers of this product.

If they can’t supply original replacement

part(s)callDESAInternational’sTechnical

Service Department at 1-800-323-5190 for

referral information.

WhencallingDESAInternational,haveready

• your name

• your address

• model and serial numbers of your heater

• how heater was malfunctioning

• type of gas used (propane/LP or natural gas)

• purchase date

EQUIPMENT SHUTOFF

VALVE - GA5010

Equipmentshutoffvalvewith1/8"NPTtap.

Usually, we will ask you to return thepart to

the factory.

PARTS NOT UNDER

WARRANTY

Contact authorized dealers of this product

or Parts Central (see page 19). If they can’t

supply original replacement part(s) call

DESA International’s Parts Department at

1-800-972-7879 for referral information.

WhencallingDESAInternational,haveready

• model number of your heater

MANUALLY-CONTROLLED

BLOWER KIT - GA3750

• the replacement part number

Provides better heat distribution. Features

variable speed control knob.

THERMOSTATICALLY-

CONTROLLED BLOWER KIT

GA3650TA (Not Shown)

Provides better heat distribution. Features

variable speed control knob.

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

NOTES

_______________________________________________________________________________________________

107435

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.

Wereservetherighttoamendthesespecificationsatanytimewithoutnotice.Theonlywarrantyapplicableisourstandardwrittenwarranty.

We make no other warranty, expressed or implied.

LIMITED WARRANTY

VENT-FREE PROPANE/LP GAS PEDESTAL STOVE

DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first

purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions.

To make a claim under this warranty the Bill of Sale or cancelled check must be presented.

Thiswarrantyisextendedonlytotheoriginalretailpurchaser.Thiswarrantycoversthecostofpart(s)requiredtorestorethisheatertoproper

operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained

through authorized dealers of this product and/or DESA International who will provide original factory replacement parts. Failure to use

original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in accordance with all local

codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged

as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor,

transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT;

THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION

OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA

INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNA-

TIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential

damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

For information about this warranty write:

INTERNATIONAL

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

www.desatech.com

107435 01

107435-01

Rev. B

06/01

NOT A UPC

Download from Www.Somanuals.com. All Manuals Search And Download.

Compaq Scanner S4 100 User Manual
Continental Electric Toaster CE23411 User Manual
Crown Audio Stereo Amplifier SST 4632 User Manual
Dimplex Fan CFS120 User Manual
Eclipse Fujitsu Ten GPS Receiver AVN4400 User Manual
Edimax Technology Network Card Wireless LAN USB Adapter User Manual
Elation Professional Indoor Furnishings 216 User Manual
EVGA Computer Hardware 113 M2 E113 User Manual
Fisher Paykel Ventilation Hood HS60CIW1 User Manual
GE Monogram Refrigerator ZIC360N LH User Manual