WOOD PELLET FIRED
Whole Hog
1050
680
570
450
Tailgat er
Mesquite
Hickory
Alder
Oak
Apple
Cherry
Pecan
Toll Free 1-877-303-3134
www.countrysmokers.com
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGERS & WARNINGS
FAILURE TO FOLLOW THE DANGERS, WARNINGS AND CAUTIONS CONTAINED IN THIS
OWNER’S MANUAL MAY RESULT IN SERIOUS BODILY INJURY OR DEATH, OR IN A FIRE
OR CAUSE DAMAGE TO PROPERTY.
DO NOT PLACE THE “TAILGATE” MODEL DIRECTLY ON A COMBUSTIBLE SURFACE. THERE MUST BE
A NON-COMBUSTABLE SURFACE BETWEEN THE SMOKER AND A COMBUSTIBLE SURFACE.
•
Do not store a spare or disconnected liquid propane cylinder under or near this barbecue.
•
After a period of storage, and/or non-use, the Louisiana Grill Barbecue should be checked for burner
obstructions before use. See instructions in this manual for correct procedures.
•
•
Do not put a barbeque cover or anything flammable on, or in the storage area under the barbeque.
Children should never use your Louisiana Grill barbeque while unattended. Accessible parts of the
barbeque may be very hot. Keep young children away while it is in use.
•
You should exercise reasonable care when operating your Louisiana Grill barbeque. It will be hot
during cooking or cleaning and should never be left unattended or moved while in operation.
•
•
•
•
•
•
Do not use lava rock, wood chunks or charcoal in your Louisiana Grill.
Never lean over open grill or place hands or fingers on the front edge of the cooking box.
Should a grease fire occur, turn off the control and leave lid closed until the fire is out.
Do not enlarge burn grate orifices, igniter holes or burner pots when cleaning the grill
“Louisiana Grills” should be cleaned on a regular basis.
Use heat-resistant barbeque mitts or gloves when operating barbeque.
WARNING:
Do Not transport your “Country Smoker” while operating or while the smokin’
grill is HOT. Make sure the fire is completely out and that the smoker is com-
•
•
•
•
Do Not use your grill in the rain or around any water source.
Keep the back side of the grill a minimum 12 inches or safe distance from combustibles.
Always unplug the grill before servicing.
If the Country Smoker is stored outside during the rainy season or seasons of high humidity care
should be taken to insure that water does not get into the pellet hopper. Wood pellets, when wet,
expand greatly, break apart, and could jam the feed system.
It is a highly recommended practice to always go through the basic SET UP
PROCEDURES after every 1 to 2 cookings. This will ensure proper ignition, heat
output and many continuous happy grilling experiences.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
UNPACKING YOUR GRILL
PROPER COMPONENT PLACEMENT
HOW YOUR LOUISIANA GRILL WORKS
TAILGATE MODEL
5
5
6
7
8
9
450, 570, 680 MODELS
1050 & THE WHOLE HOG MODELS
STANDARD FEATURES
ARCHED FLAVOR GUARD
BURN POT & BURN GRATE
CONTROL PANEL
10
10
11
12
12
12
13
FAN COOLED HOPPER
PAINT GRADE FINISH
COOKING GRIDS
ABOUT WOOD PELLETS
OPERATION
INITIAL SET-UP
14
15
17
18
19
GETTING STARTED
LIGHTING – AUTOMATIC
LIGHTING – MANUAL
SHUTTING OFF YOUR SMOKER
MAINTENANCE
GRILL MAINTENANCE
19
21
SLOWING DOWN FOR THE SEASON
WARRANTY
LIMITED WARRANTY
22, 23
WIRING DIAGRAM
PARTS & SERVICE
24
24
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING YOUR COUNTRY SMOKER
Your new Louisiana Grill “Country Smoker” may require some assembly. Please note that during shipping some
movement may have taken place, so a complete visual inspection is required.
TIP
Be sure to inspect entire grill after removing the protective shipping carton.
Report any damage to your local dealer immediately.
Shipping damage is not covered under warranty.
TG300 model
Tool Required:
1 - Phillips Screwdriver 5/8” socket and driver
Procedure:
You will find 4, 3” long Phillips wood screws inside securing the grill legs to the shipping crate. Back these out.
Gently remove your grill from the shipping pallet and place either on a non-combustible surface or install on the leg
system.
450, 570, 680, 1070 and Whole Hog model
Procedure:
You will find the smokin grills attached to the shipping pallet using 2 x 5/8” bolts. Reach under the shipping pallet
and completely back out the threaded bolts. Gently remove your grill from the shipping pallet and install the 2
threaded levellers on the bottom of the engineered legs.
PROPER COMPONENT PLACEMENT
Proper placement is vital to proper performance.
During shipping and after any general movement, it is important to
inspect and ensure the proper placement of key component parts.
2
1. Burn Grate and Burn Pot
1
To help in making cleaning easier, you can remove the burn grate (
and burn pot ( ).
B)
3
A
Remove any debris from the burn pot area. This reduces the possibility
of air leaking around the bottom edges.
Line the bottom of the smoker with heavy duty aluminum foil.
Re-install the pot and grate..
Ensure that the notched portion (C) of the Burn Pot (A) is pushed,
tight, all the way into the side wall of the smokin grill.
1
B
C
B
Install the Burn Grate (B). The larger back lip of the grate installs under
the pellet drop chute. The igniter holes should be exposed through
the slot in the bottom of the burn grate. The burn grate should be a
snug fit.
A
2
2 . Arched Flavor Guard Level
To check for proper height, the bottom of the mounting bracket (
B)
should not be within the pellet drop chute area.
If you do need to adjust the bracket, loosen off the two (2) phillips
screws, lift the bracket and re-tighten the srews.
A
The “Arched Flavor Guard” (A) then clips easily over the adjustable
mounting bracket ( ).
B
3 . Grease Can Hanger
The Hanger ( ) is designed to drop through the grease spout, from
the inside of the barrel.
Lift the tab on the Beverage Can straight up, then the tab simply hooks
onto the hanger extending.
3
A
J
A
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW YOUR COUNTRY SMOKER WORKS 101
Your Louisiana Wood Pellet Grill combines many unique features with time proven pellet-burning technology.
Together they give you perfect control, quick, savoury-and absolutely fool proof cooking results every time.
• The perfect barbeque experience starts with filling your hopper(2) with all natural wood pellets.
• Click the “Power Switch” to the “ON” position (17) this activates the “Fan” (6) used to cool the hopper (16), cause
the pellets to burn and results in convective cooking.
• Pushing the “Start Touch Pad” activates the “Electronic Auto Igniter” (8) and the pellet feed systems (5).
• A motorized rubber wheel (3), delivers the pellets to the burn grate (7). Your Louisiana Grill uses “Top Feed”
technology which means the “Feed Wheel” delivers the wood pellets up above the burn pot area and then the
pellets fall down a chute in to the burn area. The flexibility of the “Feed Wheel” and the open design reduce the
possibilities of “jams” and allows for the use of less than premium quality fuel.
• Adjusting the “Temperature Control Switch” (17) sets the speed of the motorized feed wheel and the temperature
output.
• The “Electronic Auto Igniter" (8) activates for approximately 7 minutes, igniting the pellets in the burn grate (7).
• The combustion / cooling fan (6) provides combustion air to the burn grate as well as causes air movement in
the cooking area, resulting in convection cooking (14).
• The fuel burns in the burn grate (7), hot and intense, somewhat like a forge. The fly ash is directed downward by
the “Arched Flavor Guard” (12), and can be cleaned out periodically from inside the bottom of the barrel.
• The “Arched Flavor Guard” (12) also protects the food from direct flame, gives a large hot metal area to help
evaporate the juices back into the cooking, channels excess grease directly to a grease pail (11), and distributes
the heat evenly throughout the cooking area.
• The natural smoke flavour produced by the burning pellets, the smoke produced by the “Arched Flavor
Guard”(12), and the air circulating throughout the cooking area, combine to give you that savoury flavour that is
unique to pellet grills and will win you rave reviews each time you use it.
TIP Your Country Smokin Grill can run efficiently over extended periods of
time and at different heat output levels as long as the fuel supply is
uninterrupted and timely cleaning and maintenance is performed.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
YOUR NEW “TAILGATER/ RV SMOKIN GRILL’’
Dome Thermometer
14 Gauge Steel Construction
Large 8 lb. Hopper capacity
Easy to flip up top
Paint Grade Finish
easy touch-up and maintenance
Cust om col or s.
Fan Cooled Hopper and
Feed System.
Fan forced combustion
and “Convection Cooking”
3 Stainless Stay Cool Handles
1 peice “Arched Flavor Guard”
Reduces flare-ups, increases
smoke flavor, channels grease
to collector pail, and evenly
distributes heat.
Auto Start Button & Electric Igniter
eliminates the need for
matches & starter fluids.
Full Range Temperature Control
gives range of 180 to 550+ degrees,
giving more cooking options, from
hot smoking to searing.
Primer Button aids in
quicker heat recovery or
increasing smoke intensity.
Lightweight and easy to move
perfect for theRV, camping or
tailgate party.
MODEL
COOKING AREA
ELECTRIC
SIZE H X W X D
23 X 32.5 X 19.5
WEIGHT
72 lbs.
TG300
110 Volt 60HZ 5 amp
3 prong grounded plug
10 amp GFI
308 inches of cooking surface.
Can hold a 25 lb. Turkey.
750 watt invertor with igniter
75 watt invertor without igniter
OPTIONS:
Hopper Extension
Easy add-on for those
extended smokin
times`
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
YOUR NEW “450, 570, 680”
WOOD PELLET FIRED SMOKIN’ GRILLS …
Dome Thermometer
Large 8 lb. Hopper capacity
Easy flip up top
14 Gauge Steel Construction
Pat ent ed “Paddle Wheel”
Feed system
Coldsmoker ready
(add-on option)
Fan Cooled Hopper and
Feed System.
2 Stainless Stay Cool Handles
Fanforcedcombustion
and “Convection Cooking”
1 peice “Arched Flavor Guard”
Reduces flare-ups, increases
smoke flavor, channels grease
to collector pail, and evenly
distributes heat.
Auto Start Button &Electric Igniter
eliminates the need for
matches & starter fluids.
Grease Catcher
makes clean-up and
disposal easier.
.
Full Range Temperature Control
gives range of 180 to 550+ degrees,
giving more cooking options, from
hot smoking to searing.
Paint Grade Finish
easy touch-up and maintenance
Cust om col or s.
Primer Buttonaids in
quicker heat recovery or
increasing smoke intensity.
Easy move wheels
Levellinglegs
MODEL
COOKING AREA
ELECTRIC
SIZE H X W X D
WEIGHT
111 lbs.
43 X 39.5 X 23
450
110 Volt 60HZ 5 amp
3 prong grounded plug
10 amp GFI
450 inches of cooking surface.
128 lbs.
132 lbs.
43 X 45 X 23
43 X 51 X 23
570 inches of cooking surface.
680 inches of cooking surface.
Same
Same
570
680
OPTIONS:
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
1050 AND
THE WHOLE HOG
DUAL large 8 lb. Hopper capacity Removable Center Barrier
Easy to flip uptop
Can use as two separate Smokin Grills
or divider can be taken out to cook
that WHOLEHOGor feedacrowd
(available only on Whole Hog unit)
DUAL Dome Thermometers
14 Gauge Steel Construction
DUAL Patented “Paddle Wheel”
Feed system
DUAL Fan Cooled Hopper and
Feed System.
Stainless Stay
Cool Handles
Fan forced combustion
and “Convection Cooking”
Auto Start Button & Electric Igniter
eliminates the need for
matches & starter fluids.
DUAL 1 peice “Arched Flavor Guard”
Reduces flare-ups, increases
smoke flavor, channels grease
to collector pail, and evenly
distributes heat.
DUAL Grease Catcher
makes clean-up and
disposal easier.
.
Full Range Temperature Control
gives range of 180 to 550+ degrees,
giving more cooking options, from
hot smoking to searing.
Paint Grade Finish
easy touch-up and maintenance
Cust om col or s.
Primer Button aids in
quicker heat recovery or
increasing smoke intensity.
Easy move wheels
Levelinglegs
MODEL
COOKING AREA
ELECTRIC
SIZE H X W X D
WEIGHT
331 lbs.
110 Volt 60HZ 5 amp
3 prong grounded plug
15 amp GFI
46 X 77 X 26
1050
1050 inches of cooking surface.
347 lbs.
46 X 84 X 26
Same
1320 inches of cooking surface.
Or 2 x 660 inch cooking surfaces
WHSH1320
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD FEATURES
ARCHED FLAVOR GUARD”
All “Country Smoker” models come with a 14 gauge “Arched Flavor Guard”,
designed to withstand high temperature and give years of performance. The
“Arched Flavor Guard” has been designed to keep the flame out of direct contact
with your cooking surface, thus helping to reduce the chance of flare-ups. The
“Arched” design increases the amount of hot surface area to allow more fats and
juices from the meats to evaporate as smoke flavor, back into the meat. As well you
will note the bent edges running down the length of the back and front of the angled,
arched steel; these are to help in channelling the excess grease directly to the one
end of the smoker where it is then allowed to collect in a convenient removable pail.
The unique design of the flavour guard also directs the majority of fly ash down
toward the bottom of the barrel, while allowing for the fan forced heated air to
circulate around the barrel causing convective cooking.
AUTOMATIC IGNITER
The 300 watt electric igniter eliminates the need for messy starter fluids or gels. It is
safe and easy to start, even the little beginner “Pit Master” can start a Country
Smokin Grill. The igniter is simply a hot rod encased in a stainless steel holder. This
style of igniter has been used throughout the pellet stove industry for years. The
combustion/cooling fan blows air into the back of the igniter assembly and the super
heated air is allowed to exit through the two holes found in the burn grate area. As
the pellets begin to heat up they eventually break out in flames, this is known as
spontaneous combustion. The igniter will stay activated for 7 minutes. If for any
reason the igniter fails, you can start the grill manually.
NOTE: The igniter can be disconnected, to allow your country smoker to be
run with a minimum 75 watt inverter. (See manual starting procedures to
operate).
BURN GRATE (B)
The burn grate is constructed out of stainless steel and is the heart of your grill. The
burning temperature in the pot can reach temperatures of 1700 to 2000ºF. The air
holes are designed to allow the right combination of fan forced air to force the wood
pellets to burn hot and clean while grilling or allow them to smoulder and produce
the savory smoke while in the smoke mode. The bottom is notched out to allow the
grate to set over the electric igniter, allowing the heated air within the ignitor casing
to heat up the pellets until they spontaneously combust. The burn grate should be
checked after every major use to ensure that the combustion air holes are not
clogged and to ensure the igniter holes are clean.
B
C
A
BURN POT (A)
The burn pot is used to hold the “Burn Grate”, the “Igniter” assembly and to channel
the fan forced combustion air. The pot has been designed to be moved easily, to
aid in cleaning and replacement of the igniter. It is very important that the burn
pot is seated properly in order to ensure proper combustion and heat output.
The burn pot needs to be pushed in tightly against the side of the barrel. (c) Also
ensure that there is no foreign matter under the burn pot that may lift the pot off the
bottom of the barrel. This would allow combustion air to leak out again reducing the
heat output of your grill.
(see proper placement on page 5 of this manual).
PATENTED “PADDLE WHEEL” FEED
The heart of the feed system is a rubberized “paddle wheel”. This wheel is highly
flexible thus allowing different quality of pellet fuels to be used while reducing the
possibility of “jams” taking place. The paddle design also helps in maintaining a
constant and even feed of the fuel to the fire resulting in better and consistent
temperature control. The “paddle wheel” is run by a 1 rpm motor and is timed to
operate for three seconds. (see control board for further information).
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD FEATURES CONT...
CONTROL PANEL
Board Features
Power Switch
MEDIUM
PRIME
START
POWER
Used to turn both the power “ON” and the
combustion / cooling fan. Also activates the
“Shut Down” of the smokin grill.
POWER
ON
HIGH
LOW
OFF
START Touch Pad
Used to activate the “Start Up” mode. The
“Paddle Wheel” feed system will begin to
operate, the Power LED will illuminate blue,
and the Auto Igniter will begin to glow.
SMOKE
PRE-HEAT
PRIME Touch Pad
When this touch pad is pressed and held, the Fuel Feed system will turn and feed more pellets to the burn
grate. This can be used to add more fuel just before opening the grill lid, to help with quicker heat recovery.
It can also be used to add more fuel while smoking, to increase the smoke intensity.
POWER LED
Will illuminate blue when the Power Switch is on and the Start touch pad has been pushed. It will continue
to illuminate until the Power switch has been pushed OFF and the board has completed the automatic 15
minute Shut Down mode.
FEED POTENTIOMETER or Temperature Control
Used to control the frequency the Paddle Wheel feed system feeds pellets to the burn grate, thus effecting
the heat and smoke output. The Feed Potentiometer is NOT active when the grill is in the 7 minute Start Up
mode, giving you the ability to set it at PREHEAT while ensuring proper ignition.
How the Board Works 101
START UP Mode
Upon turning the Power switch to the “ON” position, setting the Feed Potentiometer to the PREHEAT position and then
pressing the Start touch pad, the board will activate the Start Up mode. Start Up will start the combustion / cooling fan,
the feed system and the igniter. The Start Up mode will last automatically for 7 minutes and the feed rate is factory set
by the control software program.
OPERATING Mode
After the Start Up mode is complete, the Feed Potentiometer is fully functional. The feed system is designed to feed fuel
for 3 seconds then stop feeding at preset times managed through the potentiometer. The “Off” times range from 35
seconds for “Smoke” to 3 seconds for “Preheat”. Because the all natural wood pellet fuel is dry and consistent, it is easy
to keep a close to constant temperature.
NOTE: Keep in mind that all Louisiana Wood Pellet Grills are designed to operate with the lid closed and that
the external temperatures, wind, rain, and humidity will effect cooking times and heat output.
SHUT DOWN Mode
When finished “Savoring the Flavor” simply push the Power Switch to the “OFF” position. The control will begin a 15
minute cool down cycle by stopping the Paddle Wheel feed system from running, while keeping the Combustion /
Cooling fan running to cool the grill. If you do find more food to grill or bake, you can turn the Power Switch to the “ON”
position within the first 3 minutes and the grill will continue to operate as normal. If you miss the 3 minute window, you
must go through the Start Up Mode again.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD FEATURES CONT ...
“FAN COOLED HOPPER”
The entire line of Country Smokers utilizes the exact same Hopper and component
parts. To increase the life of your grill and its main working component parts the
Combustion / Cooling fan is used to perform 3 main functions:
1. Pressurize the internal hopper compartment to cool the wiring and electrical
component parts, the “Paddle Wheel” feed system and the wood pellet fuel.
2. Forces constant air movement between the hopper and grill barrel wall.
Because of the higher temperatures needed for searing and because of the
longer length of time a pellet grill can operate, to slow smoke a whole hog, air
movement is used to provide a barrier between the two surfaces. Note the air
slots found at the top of the hopper, between the lid and the grill.
Exhaust Air
Ensure that these do not get blocked off at any time.
3. To provide combustion air allowing the pellet fuel to burn properly. The fan forced
air is then used to provide “Convection Cooking” within the smokin grill.
Convection cooking locks in the juices and distributes the heat evenly throughout
the grill resulting in that savory flavour and near perfect cooking.
Top View
Air Cooled Hooper
PAINT GRADE FINISH
Louisiana Grills uses a “High Heat BBQ Paint” finish throughout the entire line of
Country Smokers. This is done to allow easy and trouble free maintenance, adding
to the life and look of your smoking grill. Baked enamel and porcelain finishing
require as much, if not more, maintenance and up keep. If they do scratch or chip
and moisture gets between the surface and the exposed metal, the problem becomes
even larger.
“Surface Rust” and “Food Acids” are two of the most common factors
that effect your smokers finish. Surface rust can develop for a number of reasons;
such as pets, kids, accidents, weather, etc. Acids that are found in many common
foods and meats can also act as a corrosive on most finishes. A paint grade finish
may require a periodic sanding and a touch-up painting once a season to maintain
that just new appearance. Louisiana Grills uses a Black color, “Stove Bright” brand,
High Heat BBQ Paint. This can be purchased from your local dealer or through
Louisiana Grills. This paint is a silicone epoxy base and is designed for up to 1100°F
(600°C) .Paint Grade allows flexibility in the color you may desire to match the decore
of your cooking area or your favorite team. A good quality grill cover is a great
investment in keeping your grill looking good and lasting longer.
(see maintenance for further details)
PORCELAIN COATED COOKING GRIDS
Your Country Smokin Grill comes complete with porcelain coated cooking grills or
grids, as they are called by the “Pit Masters”. Porcelain grids may not have the same
heat retention as cast iron, but they do show “grid marks” and are never easy to
clean. To maintain the searing and grilling performance of your grid, as well as their
longevity, some special care and maintenance is required.
GREASE CATCHER
All Country Smokers use the “Arched Flavor Guard” system that channels any excess
grease, that does not evaporate, directly to a sealed grease catch area. From here
any excess grease is directed to the drop spout where it is disposed in an easy to
replace, low cost soda or beverage can of your choose. The can is hung in place
using the J style hook that is mounted through the grease spout. Simply by lifting the
pull tab from the beverage can, upwards, allows the can to easily hook on to the J
hook. Allow the grease to cool before removing the can or for those extra fatty
foods, you may need to replace the can while using the smoker. If this is the case be
sure to wear an oven or bbq glove, as the can will be hot and cause burning.
J
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT WOOD PELLETS
They are no thicker than the eraser on the end of a pencil, people who see them for the first
time think they look like rabbit food, but there is nothing small about the heat energy in a
wood pellet. These clean burning wood pellets generate about 8200 BTU’s per pound with
very little ash and low moisture content.
Barbeque wood pellets are produced in the same matter as wood pellet fuel is produced for
home heating. Pure raw material (sawdust) is pulverized with a hammer mill and then dried.
The dried material is then processed under heat and pressure. Lignin, which is the natural
glue, which holds plant fibre together, softens above 100º C, permitting the material to
change shape. The hot lignin then acts like a binding agent to bond the pellet together. The
heated material then goes through a hard steel die, much like a meat grinder, which rotates
against rollers forcing the material through the die with pressure over 3 000 PSI. As the
pellet is forced through the die it is sheared off at a specific maximum length, cooled,
screened, vacuumed, and then bagged into 10, 20 or 40 lb bags.
General specifications for barbeque pellets are: 100% pure hardwood, no additives, 1”long or
less in length, ¼” diameter, less then 2% ash content, less then 2% fines, under 10%
moisture content, approx. 8200 BTU’s per lb. and about 40 lbs per cubic ft. density.
WARNING! Using other brand Barbecue Pellets may only enhance your
grilling experience.
(and will not void your warranty)
f
Mesquite, from the Aztex “mizquiti” (which means “the honey tree”); true to its name gives a delicate, subtle, sweet
flavour to grilled foods- especially good with poultry and seafood.
Hickory intensifies the flavour of food with a robust, tangy taste that is better suited to red meat than to poultry and
fish.
Apple or fruitwoods, many from orchards destroyed by fire or old age, are a big hit. Like its mesquite counterpart,
the heaviest branches of the apple tree is heated to kill insects, then chipped, made into pellets, and packaged for
retail. Apple or any fruitwood, adds a mild sweetness to everything that you cook and is highly recommended for any
baking.
Beef
X
Buffalo Lamb
Pork
Poultry
Fish
Vegetables
Baking
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Hickory
Mesquite
Alder
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Apple
X
X
Cherry
Orange
Pecan
Oak
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Maple
Be brave, think outside the bag, try different varieties or mix them together to customize your blends.
barbecue pellet manufactures.
Mesquite
Hickory
Ald e r
Oak
Apple
TIP Always store your pellets in a dry area. Avoid any
contact or exposure to moisture. This will cause the
pellets to absorb the moisture and will result in lower
BTU output or the pellets to swell and break apart. Use
a moisture proof re-sealable tub or bucket.
.
Cherry
Pe c a n
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP PROCEDURE
Please note that during shipping some movement may have taken place, so a complete visual inspection is
required. Please follow these Initial Set-up procedures to insure the proper and safe operation of your grill.
Note:
Do not plug your grill into an electrical outlet until this procedure is complete.
TIP It is a highly recommended practice to always go through these basic
SET UP PROCEDURES after every 1 to 3 cookings. This will ensure proper
ignition, heat output and many continuous happy grilling experiences.
Open the SMOKER LID and remove the
Cooking Grids (13). “Tailgate” comes
with 1 grid, the “450”, “570”, “680”, “1080”
and “Whole Hog” models come with 2
sections.
Remove the “Arched Flavor Guard”
cooking surface (12).
The “U” shape sits upside down to help
distribute the heat and to keep fly ash to
a minimum. The flame deflector also
keeps the flame from making direct
contact with your cooking.
Remove the stainless steel burn grate (7)
and check the burn pot (9) area, remove
any foreign items. Ensure that the air
holes in the grate`(7) and the igniter (8)
are clear of debris.
You can line the bottom of the Smokin
Grill with heavy-duty aluminium foil. Line
from left to right, starting under the burn
pot (9) area and going to the grease stop. This will make clean-up and general maintenance easier.
Install the Catch Bucket Hanger and Bucket (11)
Re-install the burn pot (9). Ensure that the pot is sitting snug to the bottom of the barrel and that it is slid all the way
into the side of the barrel opening.
Next re-install the burn grate (7). Ensure that the stainless steel grate is setting down and snug in the burn pot with the
two igniter holes (8) visible and clear of obstructions.
Re-install the “Arched Flavor Guard” (12). This mounts back on the side bracket located on each side of the burn area.
The opening of the “U” shape should be facing downwards. One end of the Flavor Guard (12) does have a slot cut into it.
This hooks over the moveable hanging bracket found over the pellet drop chute area. You may want to line the Arched
Flavor Guard with heavy duty aluminium foil, again to aid in clean-up.
Reinstall the Cooking Grids (13).
Open the Pellet Hopper Lid (1), found on the side of your Smokin Grill. Check for any foreign objects.
Fill the hopper(2) with your choice of all natural wood pellet fuel. Close the hopper lid.
Plug your “Country Smoker” into the nearest grounded 110 volt AC outlet, minimum 5 amp. (10 amp for dual hoppers)
You are now ready to push the Power Switch (17) and Start touch pad to enjoy that savory taste of pellet convection
cooking.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
With today’s lifestyle of striving to eat healthy and nutritious foods, one factor to consider is the importance of reducing
fat intake. One of the best ways to cut down on fat in your diet is to use a low fat method of cooking, such as grilling.
Throughout this manual, you will notice the emphasis on grilling food slowly at MEDIUM temperature settings. Because
of the benefit of convection cooking, and the use of the “Arched Flavor Guard”, your Country Smoker Grill will enable
you to avoid flare-ups and maximize the nutritional value of the foods that you cook.
Following is a list of the important tips that will contribute to the cooking perfection that you can
expect when using your Louisiana Grill.
Environment
As with all barbecues, the outside weather conditions will play a big part in the performance of your Country Smoker
and the cooking times needed to perfect your culinary delights. Your Country Smoker, because of its single wall
construction, should be considered as a 2 to 3 season grill, depending on what part of country you live in. For greater
detail on grilling and weather conditions, see the “Hot and Cold” weather tips found in your Louisiana Grills Cook Book
and Recipe Keeper.
Grill Placement
The tailgate model should always be placed on a non-combustible surface when using the grill
without the leg option.
All Country Smokers should always be a minimum of 12 inches away from any wall behind the grill.
Your grill does come will wheels or casters so the smoker and vent holes found on the back, can be turned away from
the wind resulting in better temperature output. If you are able to shelter your grill from the wind this will aid in
temperature output, heat retention, and heat recovery time when opening the lid.
Operating the Grill
Initial Burn Off
Before cooking on your smoking’ grill for the first time, we recommend that you “burn off” the grill to rid it of any foreign
matter. Light and operate the grill on PRE-HEAT with the lid down for 30 – 40 minutes.
Lighting your Grill
It is recommended practise to always go through the SET UP Procedures after every 1 to 3 uses. This will
ensure proper ignition and many happy grilling experiences. Light as per instructions found in detail later in this manual.
If the grill fails to light, this is most likely due to a dirty or full burn grate blocking the auto igniter air passages. (refer to
lighting instructions found elsewhere in this manual)
Should your auto igniter refuse to ignite the wood pellets, it is easy to light your grill manually with a match and lighting
agent. (refer to manual lighting instructions found elsewhere in this manual)
Pre-Heating
It is extremely important to ALWAYS allow your grill to preheat before cooking. This allows the grill and cooking
grids to heat up quicker and the grill is able to maintain its cooking temperature once your food is placed in the cooking
area. If you do not allow the grill to preheat, you will find that it takes a longer period of time to bring both the grill and
the food to cooking temperatures.
Always pre-heat your Louisiana Grill with the lid closed. Set your control knob to PREHEAT, after ignition and the
automatic start of 7 minutes, allow the “Smokin Grill” to preheat for 10-15 minutes depending on weather. This gives
you enough time to prepare your food for the grill; as well it is the final step in cleaning your cooking grids.
Lid Position
Always cook with the lid closed. Not only does this keep the temperature even, the food will cook faster, using
less fuel. A closed lid also helps to create a smokier flavour. You can slow down your cooking by propping up
the lid using the grill lifter.
CAUTION: Grease fires are caused by not properly maintaining your grill, or failing to clean the bottom of the barrel on
a consistent basis. In the unlikely event you experience a grease fire while cooking, keep the lid closed. If it does not
go out ins a very short time, open the lid and lightly sprinkle baking soda on the fire. Be careful not to burn yourself. If
this does not work, then carefully remove the food from the grates, turn the temperature control to OFF and shut the lid
until the fire is completely out.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED CONT...
NOTE: The temperature settings on the control board are not accurate! Due to
environment, fuel and cooking conditions, the settings are only for reference!
Cooking Settings
Pre Heat
MEDIUM
PRIME
START
POWER
The PREHEAT setting will give an oven temperature
of over 500 to 600ºF (316ºC), depending on weather
conditions. This setting is used to quickly preheat
your grill as well as to finish the cleaning cycles for
the cooking grids and the “Arched Flavor Guard”.
Could also be used as a HIGH setting in extreme cold
weather conditions or if cooking with the lid open.
POWER
ON
HIGH
LOW
OFF
SMOKE
PRE-HEAT
High
The HIGH setting will give an oven temperature of approximately 450ºF – 550ºF, depending on the weather. This
setting is ideal for quickly searing steaks, hamburgers and chops.
Medium
The MEDIUM setting will give an oven temperature of approximately 350ºF (177ºC) when the lid is closed and the
weather conditions permit. This setting is recommended for finishing cooking steaks, hamburgers, chops, etc.
Excellent for baking. This setting is also used to IGNITE your Louisiana Grill, automatically. This setting allows just
enough pellets to feed and the proper air to transfer heat from the igniter to start the wood pellet fuel.
Low
The LOW setting will give an approximate oven temperature of 250ºF to 350ºF (154ºC – 177ºC). Used to prolong
cooking times or just to warm-up your left over master pieces.
Smoke
The SMOKE setting will give an approximate oven temperature of 180ºF to 220ºF. This setting is used to slow roast
and to increase the smoke flavour of your favourite food. Highly recommended for that BIG BIRD at Christmas, Easter,
Thanksgiving, Birthdays, and all other important holidays.
Smoking is a variation on true barbecuing and is truly the main advantage of grilling on a wood pellet grill. There
are two types of smoking: HOT smoking and COLD smoking. HOT smoking, just another name for barbecuing, is
generally done at 200 to 250ºF. COLD smoking is where the food is located so far away from the fire that it smokes
without cooking. Your “Louisiana Grill” is classified as a HOT smoker.
Hot smoking works best when a longer cooking time is required, such as large cuts of meat, fish, or poultry,
Experiment with the length of time you leave for smoking, before cooking thoroughly. Some chefs prefer to smoke at
the end of cooking and to keep the food warm until ready for serving. Remember practice makes perfect.
TIP The temperatures listed above are all approximate and will be affected by the
outside temperature, the amount and direction of wind present, the length and type of
pellet fuel being used and the number of times the lid is opened.
After Cooking
One of the greatest benefits of your Louisiana Grill is the minimal clean up required. When you are finished cooking and
waiting just a little while to let the flavor set in that prime selection of meat, we recommend the following:
1. Using a long handled grill cleaning brush to remove any food or build up from the cooking grids, while it is still
warm.
2. Turn the control knob to PREHEAT for 5 minutes. Let the grill heat up, then push the POWER button to the “OFF”
position and you’re DONE.
3. A quick wipe up of the stainless steel counter top, using a cloth and mild soap, let the unit cool and put your
Louisiana Grill to bed with the optional GRILL COVER.
TIP To intensify that savory smoke flavor, switch to smoke mode immediately
after putting your food on the grill. This allows the smoke to penetrate the meats
before they have a chance to sear closed.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING YOUR COUNTRY SMOKER
NOTE:
Always clean your burn grate before each use. This will ensure proper
ignition, heat output and many continuous happy grilling experiences.
Automatic Start Up
1. Ensure the POWER switch is in the “OFF” position.
2. Plug the POWER CORD into a 110 Volt grounded outlet. DO NOT break the ground end off the
cord or use a non-grounded outlet or extension cord.
NOTE: When plugged into a GFI ensure it is t least 10 amps.
Lower quality GFI’s may trip when using this appliance.
3. Open the HOPPER LID. Ensure there are no foreign objects in the hopper or “PADDLE
WHEEL” feed system. Fill hopper with all natural flavoured wood pellets.
4. Turn the FEED CONTROL (temperature output) to the “ PREHEAT” position.
5. Switch the POWER switch to the “ON” position.
•
This will start the combustion/cooling fan.
6. Press the START touch pad.
•
This initiates the start up cycle, which includes; the feed system will start to turn, the iginiter
will begin to glow and the power indicator will illuminate.
•
•
•
•
The Country Smoker now begins an automatic 7 minute “Starting Procedure”
The Feed Rate is pre-programmed to ensure proper ignition.
Your grill will begin to produce smoke while the start up cycle is taking place. Close the lid.
The pellets have ignited once the smoke has cleared. To check open the lid of your grill and a
flame will be visible in the burn pot area. You will be able to view this without having to touch
any hot surfaces.
7. Turn the FUEL FEED to PREHEAT, if not done already, and allow unit to preheat for approximately
15 to 20 minutes.
CAUTION: If excessive flame is visible i.e. “Arched Flavour Guard” is glowing bright red, turn the FEED
CONTROL down.
8. After the pre-heating is complete you are now ready to enjoy your grilling experience.
NOTE: Different wood pellets will produce different temperatures; as well the outside temperature
and weather conditions will also affect your cooking temperature. The markings on the CONTROL
LABEL are approximate.
NEVER add pellets by hand to a hot fire pot. This is dangerous and you may get seriously burned. If
you do run out of fuel and you lose your fire while cooking, Re-fill the hopper and go through the
normal LIGHTING procedure.
NOTE: If the fire does not start, the Country Smoker will continue to feed pellets. If this happens,
some unburned pellets will build up in the burn grate. To restart the fire, clean the excess pellets out of
the burn grate and follow the above steps.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING YOUR COUNTRY SMOKER CONT...
NOTE:
Always clean your burn grate before each use. This will ensure proper
ignition, heat output and many continuous happy grilling experiences.
Manual Start Up
If for any reason your electric igniter fails, you can start your “Country Smoker” manually.
1. Ensure the POWER switch is in the “OFF” position.
2. Plug the POWER CORD into a 110 Volt grounded outlet. DO NOT break the ground end off the cord or
use a non-grounded outlet or extension cord.
3. Open the HOPPER LID. Ensure there are no foreign objects in the hopper or “PADDLE
WHEEL” feed system. Fill hopper with all natural flavoured wood pellets.
4. Remove the COOKING GRIDS and “ARCHED FLAVOR GUARD” to expose the BURN GRATE AND BURN
POT.
5. Place two generous handfuls of pellets into the BURN GRATE.
6. Squirt gelled fire starter, or other approved pellet starter, over the top of the pellets or
Add a small amount of solid fuel fire starter, such as those made from sawdust and wax or use wood
shavings. Add a small amount of pellets over the fire starter.
7. Light the starter using a long fireplace match or long lighter.
WARNING: NEVER ATTEMPT TO ADD MORE STARTER INTO A FIRE THAT IS ALREADY BURNING
OR INTO A HOT BURNGRATE. YOU COULD EXPERIENCE A BURN BACK AND YOU COULD GET
SERIOUSLY BURNT.
8. Allow the starter to burn for 3 to 5 minutes.
9. Quickly and carefully replace the “ARCHED FLAVOR GUARD” and the COOKING GRIDS.
10. Turn the FEED CONTROL (temperature output) to the “ PREHEAT” position.
11. Switch the POWER switch to the “ON” position.
This will start the combustion/cooling fan.
12. Press the START touch pad.
This initiates the start up cycle, which includes; the feed system will start to turn and the power indicator
will illuminate.
The Country Smoker now begins an automatic 7 minute “Starting Procedure”
The Feed Rate is pre-programmed to ensure proper ignition.
Your grill will begin to produce smoke while the start up cycle is taking place. Close the lid.
The pellets have ignited once the smoke has cleared. To check open the lid of your grill and a flame will
be visible in the burn pot area. You will be able to view this without having to touch any hot
surfaces.
13. Turn the FUEL FEED to PREHEAT, if not done already, and allow unit to preheat for approximately 15 to
20 minutes.
CAUTION: DO NOT USE ANY FLAMMABLE LIQUIDS SUCH A GASOLINE, GASOLINE-TYPE LANTERN FUEL,
KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR FRESHEN-UP THE FIRE!
KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE GRILL WHILE IT IS IN USE.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
SHUTTING OFF YOUR SMOKER
Your Country Smoker will give you many years of flavorful service with minimum cleaning. An important step is allowing
the grill and cooking grids to “Self Clean” by running the grill on high temperature for 5 – 10 minutes after each use.
When finished cooking on your Louisiana Grill turn the FEED CONTROL switch to the “Pre Heat” position. Let your grill
run for 5 – 10 minutes to go through its normal cleaning method. If you have been preparing meats that are extra greasy,
it is a good practise to allow the grill to burn for an extra 10 to 20 minutes. This will reduce the chances of “Flare-Up”
while preparing your next savory meal.
When complete, simply push the Power switch to the “OFF” position. Your Country Smoker will begin its automatic Shut
Down procedure. The patented “Paddle Wheel Feed” system will stop feeding fuel, the flame will burn itself out, and the
combustion / cooling fan will continue to run for a 15 minute period. When procedure is complete the Fan and the Power
LED will turn off.
If you do find more food to grill or bake, you can turn the Power Switch to the “ON” position within the first 3 minutes and
the grill will continue to operate as normal. If you miss the 3 minute window, you must go through the Start Up procedure
again.
GRILL MAINTENANCE
There are two extremes when it comes to keeping the grill clean. Those that must spit and shine the entire grill, in and
out, after every use, and those whom are convinced that cleaning only takes away from that barbecue flavor. One simple
rule; everything in moderation.
TIP Be diligent in you cleaning and maintenance program. Taking care of your
grill will add years of life to it and keeps it looking great.
STARTING THE SEASON OUT RIGHT
A little time and effort at the beginning of the season will not only help extend the life of your grill but will also ensure the
reliability of it, and make you look like the “King or Queen of the Grill”! Most of the cleaning techniques are below. Check
with your local dealer, they may provide a yearly maintenance program and inspection service.
STAINLESS STEEL WORKING SURFACES
ALWAYS clean dirt and dust off all stainless steel surfaces before you begin to cook. The dirt can cook into the metal and
discolour it. These can be easily cleaned with hot soapy water and a soft cloth. A quick swipe of “Stainless Steel Cleaner”
and a soft rag will also work, but you must be careful not to apply it to the painted surfaces or interior parts. With the
popularity of stainless steel appliances increasing, there are now many commercial products made to clean and protect
stainless steel surfaces.
PAINT GRADE SURFACES
Paint and maintaining painted surfaces are not covered under warranty. This is part of the general
maintenance and upkeep.
Be sure to preheat the unit for a least 30—40 minutes before using for the first time. This allows the paint to cure and
allows the new paint smoke and smell to burn off. Once cured it can be washed with hot soapy water. Do not use oven
cleaner, abrasive cleaners or abrasive cleaning pads on the outside surfaces.
We use “Stove Bright” brand, Hi-Heat Black BBQ Paint.. Stove Bright also makes many more colors in high-heat stove
paint, if you ever wanted to change the color to match the décor or favorite team.
To help maintain your finish, follow these easy steps:
1. Wipe your smoker down with a warm, soapy damp cloth after each use.
2. Keep your smoker covered when its not in use. Purchase a Louisiana Grill heavy duty cover from your local dealer.
3. If you do have areas that need attention, we recommend:
A. Clean the surface with a mild degreaser and hot soapy water.
B . Remove any loosened paint with a fine sand paper or wire brush..
C. Wipe off all loose grit with a clean rag.
D. Apply thin coats of touch up paint. Paint dries tack free in 20 minutes and to handle in 30 minutes.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
GRILL MAINTENANCE CONT...
COOKING GRIDS
When new, wash thoroughly with warm soapy water, place back in the smoker and “Preheat” the grill for 20 to 30 minutes.
After the completion of grilling, open the lid and with a long handle grill cleaning brush, give the grids a thorough cleaning.
If you do not have a cleaning brush use long handle tongs and a balled up piece of aluminium foil wrap. Next turn the grill
to “high” or “preheat” until only an occasional wisp of smoke is seen (about 5 minutes). This will remove most of the
material that builds up on the cooking grids.
The next time you grill allow the smoker to preheat for 10 – 15 minutes to complete the cleaning cycle. Give the grids a
quick wipe down with your cleaning brush. Applying a thin coating of oil on the grids before placing your meat on them will
also decrease your cleaning time, as well as allowing to move your food easily without sticking and tearing.
COVER-UP
Your Louisiana Grill cover will help in protecting your grill from the detrimental effects
of weather and outside pollutants. As with any outdoor product, however, a cover is
only as good as the maintenance given to the grill. Following the recommended
maintenance included in this manual will add greatly to the life of your grill.
Helpful Hints
DO’s
•
Keep your Country Smoker cover clean. This is your best protection against
mildew which will form on any dirt or foreign material allowed to accumulate on
tops or bottoms of fabric. Use a cleaner such as Armor-All, or a product that
will not only clean but also protect.
•
•
•
Have any small tears or punctures repaired promptly.
Keep away from pets.
Keep all shrubs and vines away from your grill cover as many plants contain acids, which harm fabrics.
DO NOT
•
•
•
•
•
Cover your grill while the grill is still hot
Store anything on the top of your grill cover.
Permit leaves, twigs or other organic debris to remain on the cover for long periods of time
Use high-pressure hoses or steam to clean.
Use wire or stiff brushes, harsh detergents, abrasive cleaners or chlorine on your grill cover.
“ARCHED FLAVOR GUARD”
This requires very little work, because of its construction and the type of material used. From time to time you may need to
brush off any burnt leftover. The best time to clean and inspect is when you perform the initial set-up procedures after
every 1 to 3 uses.
To speed up cleaning we recommend that you line the Arched Flavor Guard with aluminium foil. This foil should be
replaced after each use.
The grease channels do need to be cleaned from time to time to eliminate build-up and allow the grease to flow freely to
the grease catch area.
THE COOKING BARREL
To start the season right, then maybe 2 to 3 times during the grilling season, it is recommended to remove the Arched
Flavor Guard, Burn Grate and Burn Pot, to remove any ash build-up or burn debris that has accumulated. Make sure the
grill is COMPLETELY COLD before using your shop vacuum or before scooping out and disposing of the ashes.
You may want to use hot water and a de-greaser to clean the entire inside of the barrel. This does reduce grease build-up
and the possibilities of flare ups.
To aid in cleaning, it is recommended to line the bottom of the barrel with aluminium foil. Starting tight from the burn side
of the barrel to the grease catch area. Then re-install the Burn Pot and Burn Grate.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
GRILL MAINTENANCE CONT...
BURN POT
The proper seating of the burn pot is crucial to proper grill performance. The Burn Pot placement should be
checked after every burn or after the grill has been moved. Because the burn pot is used to channel the fan forced air
into the burn grate, there is very little maintenance to be done in this area. Occasionally you may either vacuum or brush
out any build-up of ash or burn debris that has fallen below the burn grate. Before replacing the burn pot always clean
any debris from around or under the burn pot seating. It is crucial that the burn pot is seated tight to the side wall
and that it is tight to the barrel bottom.
STAINLESS STEEL BURN GRATE
Periodically check the air holes found in the sides and bottom of the burn grate for any blockages or build-ups.
Using a wire brush or flat-head screwdriver, scrape off any build up or blockage. When reinstalling the grate also confirm
the proper positioning in the burn pot. The grate should be level from side to side and from front to back as well as
should have a snug but not tight fit. The grate should not be blocking the two igniter holes.
IGNITER
The 300 watt electric igniter needs very little maintenance. Do check to confirm that the two air holes are free of debris or
blockage. As well confirm that the igniter is setting level in the burn grate.
FAN COOLED HOPPER ASSEMBLY
BE SURE TO UNPLUG YOUR GRILL BEFORE PERFORMING ANY SERVICE.
There are a number of very quick checks that should be performed on the outside of the hopper assembly.
1. Check and clean any debris from the fan air intake. E.g. Spider webs, tree fluff, etc.
2. Check and clean any debris from the air vent exhaust found at the top of the hopper.
3. Inspect and clean the fuel hopper area. The galvanized metal can be wiped down using warm water and detergent.
To aid in protecting the metal and to allow the pellet fuel to slide easily, you can apply a coating of car wax .
4. Inspect the rubber “Paddle Wheel” feed wheel. Check for any tears or wearing of the wheel.
You can remove the 6 (six) Phillip screws securing the side panel to the hopper assembly. 2 on the front, 2 on the back
side and 2 on the under side. This will allow you to perform the following within the hopper assembly:
1. Check and clean any debris within the hopper housing.
2. Check and clean any debris from the fan blades or housing.
3. Check and clean any debris from the feed wheel motor.
4. Visual inspection on the wire harness and all wire connections.
Upon inspection replace all 6 Phillip screws. Hand start each screw to ensure proper threading.
GREASE CATCH AREA AND CAN
Always be sure the grease catch area is clean and free of debris. We recommend the use of your favorite beverage can
as the grease collector for the following reasons:
1. Clean and easy disposal.
2. The upper lip of the can contains the grease drippings.
3. The can be replaced more frequently.
4. Can be replaced easily with another can while the grill is operating.
5.
Note: The can and grease will be hot. Use protection when replacing while hot.
During the warmer months empty any grease build-up on a more frequent basis to avoid it from going rancid and to avoid
having any extra creatures enjoying your grill.
Slowing Down . . . Not Putting Away for the Season
We recommend that at least once a month, while your grill is cold, that you should perform not only the above
maintenance procedures, but also include the following:
Using a stiff vegetable brush knock-off any built-up scale on the inside walls of your grill. Check the inside of the lid, the
smoke deflector, and the inside walls of the cooking area.
Using an old paintbrush, brush off any ash build-up found inside the firebox, grate, and flame deflector areas.
Finally give your entire grill a good cleaning with a shop vac when cool to the touch, a quick wash and rinse and apply any
touch up paint.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
The “Louisiana Grill” wood pellet barbecue line, manufactured by Dansons Group Inc. (DGI), carries a
five (5) year limited warranty for from the date of sale to the original owner only, against defects and
workmanship on all steel parts, (excluding the burn grate), and three (3) years on electrical component
parts only. There is no specific warranty on the paint, burn grate, grill cover and all gaskets or against
damage caused from corrosion.
Conditions of Limited Warranty
1. During the term of the limited warranty, DGI’s obligation shall be limited to furnishing a
replacement for covered, failed components, F.O.B. point of shipment. As long as it is within
the warranty period, DGI will not charge for repair or replacement for parts returned, freight
prepaid, if the part(s) are found by DGI to be defective upon examination. DGI shall not be
liable for transportation charges, labor costs, or export duties. Except as provided in this
CONDITIONS OF WARRANTY paragraph, repair or replacement of parts in the manner and
for the period of time stipulated hereunder shall constitute the fulfillment of all direct and
derivate liabilities and obligations from DGI to you.
2. The warranty coverage begins on the original date of purchase and proof of date of purchase
is required to validate the warranty.
3. Repair or replacement of the “Louisiana Grill” part does not extend the limited warranty
beyond the five (5) years or three (3) years from date of purchase.
4. The pouring of liquids on your grill flame will void this warranty.
5. DGI takes every precaution to utilize materials that retard rust by using high-temperature
paint where advisable. Even with these safeguards, the protective coatings can be
compromised by various substances and conditions beyond DGI’s control.
High
temperatures, excessive humidity, chlorine, industrial fumes, fertilizers, lawn pesticides and
salt are some of the substances that can affect paint and metal coatings. For these reasons,
the limited warranties DO NOT COVER RUST OR ALUMINUM OXIDATION, unless there is
loss of structural integrity on the grill component. Should any of the above occur, kindly refer
to you Instruction Manual’s maintenance section for paint finish protection. DGI recommends
that you purchase a DGI full-length protective cover, and cover your grill when not in use.
6. The warranties are based on normal domestic use and service of the grill and neither limited
warranty coverage apply for a grill, which is used in commercial applications.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Exceptions to the Limited Warranty
There is no written or implied performance warranty on “Louisiana Grills” appliances, as the
manufacturer has no control over the installation, operations, cleaning, maintenance or the
type of fuel burned.
This limited warranty will not apply nor will DGI assume responsibility if your appliance has not been
installed, operated, cleaned and maintained in strict accordance with the manufacturer's instructions.
Burning other than quality wood pellets may void the warranty. The warranty does not cover damage
or breakage due to misuse, improper handling or modifications.
NEITHER THE MANUFACTURER, NOR THE SUPPLIERS TO THE PURCHASER, ACCEPTS
RESPONSIBILITY, LEGAL OR OTHERWISE, FOR THE INCIDENTAL OR CONSEQUENTIAL
DAMAGE TO THE PROPERTY OR PERSONS RESULTING FROM THE USE OF THIS PRODUCT.
ANY WARRANTY IMPLIED BY LAW, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS, SHALL BE LIMITED TO ONE (1) YEAR FROM THE DATE OF
ORIGINAL PURCHASE. WHETHER A CLAIM IS MADE AGAINST THE MANUFACTURER BASED
ON THE BREACH OF THIS WARRANTY OR ANY OTHER TYPE OF WARRANTY EXPRESSED OR
IMPLIED BY LAW, MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL,
INDIRECT, CONSEQUENTIAL OR OTHER DAMAGES OF ANY NATURE WHATSOEVER IN
EXCESS OF THE ORIGINAL PURCHASE PRICE OF THIS PRODUCT. ALL WARRANTIES BY
MANUFACTURER ARE SET FORTH HEREIN AND NO CLAIM SHALL BE MADE AGAINST
MANUFACTURER ON ANY ORAL WARRANTY OR REPRESENTATION.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations of implied warranties, so the limitations or exclusions set forth in this limited warranty may
not apply to you. This limited warranty gives you specific legal rights and you may have other rights,
which vary from state to state
The limited warranties for 5 (five) years or 3 (three) years are in lieu of all other warranties expressed
or implied, at law or otherwise, and DGI does not authorize any person or representative to assume for
DGI any obligation or liability in connection with the sale of the wood pellet grill. This means that no
warranties, either expressed or implied, are extended to persons who purchase the product from any
one other than DGI.
Procedures for Warranty Service
Call your nearest “Louisiana Grills” dealer for repair or replacement of your “in-warranty” parts.
Be prepared to furnish the following information:
1. Purchaser’s name, model and serial number of grill and date of purchase
2. An accurate description of the problem.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER
RIGHTS, WHICH VARY FROM STATE TO STATE
SERIAL NUMBER AND MODEL NUMBER
Your serial number and the model number of your country smoker can be found on the inside of your
hopper lid. Be sure to record these in the space provided below to aid you if they get damaged or lost.
_________________________________
Model
______________________________
Serial Number
________________________________
Date of Purchase
______________________________
Authorized Dealer
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
Country Smoker Board & Wire Harness
PARTS, SERVICE AND ACCESSORIES
Dansons Group Inc. stands behind our Authorized Dealers. We strongly suggest that if you do need to order any parts or options
or require service, that you first deal with your local dealer. Many dealers do stock parts and options. The majority of the parts
names can be found on page 5 of this manual on the “How Your Country Smoker Works” page.
If for any reason you do not have a local dealer, Dansons Group Inc. is proud to offer the best technical and sales support in the
industry. If you require parts, options, rubs and spices, or general accessories you can contact the factory directly :
Louisiana Grills Customer Service
T0LL FREE: 1-877-303-3134
TOLL FREE FAX: 1-877-303-3135
Email: [email protected]
CHECK OUR WEBSITE FOR UP TO DATE ACCESSORIES, OPTIONS, AND INFORMATION!!
Download from Www.Somanuals.com. All Manuals Search And Download.
|