DR® 6 -TON, ELECTRIC WOOD SPLITTER
SAFETY & OPERATING INSTRUCTIONS
READ AND UNDERSTAND THIS MANUAL AND ALL INSTRUCTIONS
BEFORE OPERATING THIS WOOD SPLITTER.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
CHAPTER 1............................................................................................................................. 1
INTRODUCING THE DR 6 -TON ELECTRIC WOOD SPLITTER................................... 1
Conventions used in this manual ................................................................................... 1
Specifications for the DR 6 -TON ELECTRIC WOOD SPLITTER ................................... 2
CHAPTER 2............................................................................................................................. 3
GENERAL SAFETY RULES............................................................................................... 3
Labels ............................................................................................................................... 3
Protecting Yourself and Those Around You ................................................................... 4
Operating the Wood Splitter Safely................................................................................. 4
Safety for Children ........................................................................................................... 5
Safety with Electric-Powered Machines .......................................................................... 6
Hydraulic Safety............................................................................................................... 7
Additional Information and Potential Changes.............................................................. 8
CHAPTER 3............................................................................................................................. 9
UNPACKING AND ASSEMBLING YOUR DR 6 -TON ELECTRIC WOOD SPLITTER... 9
DR 6 -TON ELECTRIC WOOD SPLITTER Controls and Features ............................... 10
Unpacking and Assembling the DR 6 -TON ELECTRIC WOOD SPLITTER ................ 11
CHAPTER 4........................................................................................................................... 13
OPERATING YOUR DR 6 -TON ELECTRIC WOOD SPLITTER ................................... 13
Before Starting the Electric Motor................................................................................. 13
Splitting Safety............................................................................................................... 15
Operating the DR 6 -TON ELECTRIC WOOD SPLITTER............................................. 16
How to Free a Jammed Log from the Wedge............................................................... 17
CHAPTER 5........................................................................................................................... 19
MAINTAINING THE DR 6 -TON ELECTRIC WOOD SPLITTER.................................. 19
Regular Maintenance Checklist before each use.......................................................... 19
Before each season........................................................................................................ 19
Adjusting the Hydraulic Fluid Level.............................................................................. 20
Sharpening the Wedge .................................................................................................. 20
Electrical Connections................................................................................................... 21
CHAPTER 6........................................................................................................................... 23
TROUBLESHOOTING................................................................................................... 23
Troubleshooting Table................................................................................................... 23
CHAPTER 7........................................................................................................................... 25
PARTS LISTS, SCHEMATIC DIAGRAMS AND WARRANTY........................................ 25
Parts List - DR 6 -TON ELECTRIC WOOD SPLITTER .................................................. 25
Schematic - DR 6 -TON ELECTRIC WOOD SPLITTER................................................. 27
Optional Accessories..................................................................................................... 28
Notes.............................................................................................................................. 28
Warranty......................................................................................................................... 29
CALL TOLL FREE 1-800-DR-OWNER
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
INTRODUCING THE DR 6 -TON ELECTRIC WOOD SPLITTER
This manual will help you set up and safely operate your new DR 6 -TON ELECTRIC WOOD SPLITTER.
Careful adherence to the safety and operating instructions in this manual will ensure many years of
productive use.
Please let us know of any questions you may have. We want to answer them as quickly as possible. When
you do call, please have your serial number and/or order number handy. For technical assistance, please
call Toll-Free 1-800-DR-OWNER (376-9637) and one of our Technical Support Representatives will be happy
to help you.
Conventions used in this manual
THIS INDICATES A HAZARDOUS SITUATION, WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH
OR SERIOUS INJURY.
THIS INDICATES A HAZARDOUS SITUATION, WHICH, IF NOT AVOIDED, COULD RESULT IN MINOR
OR MODERATE INJURY.
THIS INFORMATION IS IMPORTANT IN THE PROPER USE OF YOUR MACHINE. FAILURE TO FOLLOW
THIS INSTRUCTION COULD RESULT IN DAMAGE TO YOUR MACHINE OR PROPERTY.
Tip: This is a helpful hint to guide you in getting the most out of your DR 6 -TON ELECTRIC WOOD
SPLITTER.
Tools Needed: This indicates you will need a specific tool to perform a maintenance function on your
DR 6 -TON ELECTRIC WOOD SPLITTER.
NOTE: This information may be helpful to you.
If you are ever unsure about an action you are about to take, don’t do it, contact Country Home Products’
toll-free support at 1-800-DR-OWNER (376-9637) for help or information.
CALL TOLL FREE 1-800-DR-OWNER
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications for the DR 6 -TON ELECTRIC WOOD SPLITTER
MAXIMUM RAM FORCE
MAXIMUM LOG LENGTH
MAXIMUM LOG DIAMETER
MAXIMUM RAM TRAVEL (TYPICAL)
CLOSED GAP
12,000 lbf
20"
16"
17"
4"
RAM CYLINDER DIAMETER
2.8"
21.5 seconds at low speed/high
pressure and 11 seconds at high
RAM CYCLE TIME (TYPICAL)
VALVE TYPE
speed/low pressure
2-Speed Valve
RAM RETURN MECHANISM
RAM FACE
HYDRAULIC FLUID RESERVOIR
HYDRAULIC FLUID for 40ºF to 105ºF
HYDRAULIC FLUID for -20ºF to 105ºF
WEDGE HEIGHT
Spring
5" x 5"
6.5L
AW32
Dexron Auto Transmission Fluid
6"
MOTOR RPM
3450
1.8 HP - Continuous
2.7 HP Peak
MOTOR HORSEPOWER (Output)
MOTOR VOLTAGE
120 V/ 60hz
MINIMUM OPERATING VOLTAGE
POWER CORD
RECOMMENDED EXTENSION CORD
WHEEL SIZE
105 V
6' UL Certified
12 Gauge--Up to 33' Length
6.5"(dia.) x 2" width
169lbs
WEIGHT OF UNIT
UNIT SIZE L x W x H
41.5" x 15" x 20.5"
BOX DIMENSIONS L x W x H (no pallet)
SHIPPING DIMENSIONS ON PALLET
L x W x H
43.5" x 13.5" x 23"
43.5" x 14" x 28"
SHIPPING WEIGHT ON PALLET
202lbs
2
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
GENERAL SAFETY RULES
READ THIS SAFETY AND OPERATING MANUAL BEFORE YOU USE THE DR 6 -TON ELECTRIC WOOD
SPLITTER. BECOME FAMILIAR WITH THE SERVICE RECOMMENDATIONS TO ENSURE THE BEST
PERFORMANCE FROM YOUR WOOD SPLITTER.
Labels
Your DR 6 -TON ELECTRIC WOOD SPLITTER carries prominent labels as reminders for its proper and safe
use. Shown below are copies of all the labels that appear on the equipment. Take a moment to study them
and make a note of their location on your DR 6 -TON ELECTRIC WOOD SPLITTER as you assemble and
before you operate the machine. Replace damaged or missing safety and information labels immediately.
#211891
#206861
#212861
#211981
CALL TOLL FREE 1-800-DR-OWNER
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Protecting Yourself and Those Around You
THIS IS A POWERFUL MACHINE. YOU MUST USE PROPER CLOTHING AND SAFETY GEAR WHEN
OPERATING THIS MACHINE TO PREVENT OR MINIMIZE THE RISK OF SEVERE INJURY. THIS MACHINE
CAN CUT, AND SEVER PARTS OF YOUR BODY IF THEY BECOME CAUGHT BETWEEN THE RAM, LOG,
GUIDING PLATES AND/OR THE SPLITTING WEDGE. ALWAYS TAKE THE FOLLOWING PRECAUTIONS
WHEN OPERATING THIS MACHINE:
•
ALWAYS WEAR PROTECTIVE GOGGLES OR SAFETY GLASSES WITH SIDE SHIELDS WHILE SPLITTING
WOOD TO PROTECT YOUR EYES FROM POSSIBLE THROWN BITS OF WOOD.
•
WEAR SHOES WITH NON-SLIP TREADS WHEN USING YOUR DR 6 -TON ELECTRIC WOOD SPLITTER. IF
YOU HAVE SAFETY SHOES, WE RECOMMEND WEARING THEM. DO NOT USE THE MACHINE WHILE
BAREFOOT OR WEARING OPEN SANDALS.
•
•
AVOID WEARING LOOSE CLOTHING OR JEWELRY, WHICH CAN CATCH ON THE WOOD SPLITTER’S
MOVING PARTS.
WE RECOMMEND WEARING GLOVES WHILE SPLITTING WOOD. BE SURE YOUR GLOVES FIT
PROPERLY AND DO NOT HAVE LOOSE CUFFS OR DRAWSTRINGS.
Operating the Wood Splitter Safely
THIS IS A POWERFUL MACHINE. YOU MUST OPERATE THE MACHINE SAFELY. UNSAFE OPERATION CAN
CREATE A NUMBER OF HAZARDS FOR YOU. ALWAYS TAKE THE FOLLOWING PRECAUTIONS WHEN
USING THIS MACHINE:
•
NEVER ALLOW PEOPLE WHO ARE UNFAMILIAR WITH THESE INSTRUCTIONS TO USE THE DR 6 -TON
ELECTRIC WOOD SPLITTER.
•
TO BE SAFE, DO NOT OPERATE THE MACHINE NEAR SMALL CHILDREN OR PETS, AND NEVER ALLOW
CHILDREN TO OPERATE THE WOOD SPLITTER. RETRACT THE RAM AND STOP THE MOTOR WHEN
ANOTHER PERSON OR PET APPROACHES.
•
NEVER TEAM UP WITH ANOTHER PERSON TO OPERATE THE WOOD SPLITTER CONTROLS – THIS IS A
ONE PERSON JOB.
•
•
•
KEEP YOUR HANDS AND FEET AWAY FROM THE SPLITTING AREA WHILE THE RAM IS IN MOTION.
USE ONLY YOUR HANDS TO OPERATE THE WOOD SPLITTER CONTROLS.
DO NOT PLACE YOUR HANDS AT PINCH POINTS WHERE THEY CAN CATCH BETWEEN A LOG AND
THE WEDGE, LOG GUIDING PLATES OR THE RAM.
•
•
DO NOT PUT ANY PART OF YOURSELF, YOUR CLOTHING, OR YOUR PERSONAL PROTECTIVE
EQUIPMENT INTO A CRACK IN A LOG THAT YOU ARE SPLITTING; IT MIGHT CLOSE SUDDENLY WITH
GREAT FORCE.
NEVER SPLIT ANYTHING OTHER THAN LOGS FREE OF NAILS, WIRES, AND BRANCHES. MAXIMUM
LOG LENGTH IS 20" WITH A MAXIMUM DIAMETER OF 16" FOR THE DR 6 -TON WOOD SPLITTER.
NOTE: The log diameter does not necessarily indicate the difficulty of the split. A small diameter log can be difficult to
split if it has knots or its fiber is very tough, whereas you can split a larger log easily if its fiber is smooth and loose.
4
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
NEVER OPERATE THE WOOD SPLITTER IN AN AREA OF NATURAL GAS OR FLAMMABLE LIQUIDS.
NEVER SPLIT WOOD IN WET OR SLIPPERY CONDITIONS.
ALWAYS OPERATE THE WOOD SPLITTER FROM THE OPERATOR ZONE (FIGURE 11 ON PAGE 15).
NEVER STAND ON, STRADDLE, OR CLIMB OVER THE WOOD SPLITTER AT ANY TIME.
•
DO NOT HANDLE LOGS BY THEIR ENDS WHEN YOU POSITION THEM ON THE WOOD SPLITTER.
•
ALWAYS UNPLUG THE WOOD SPLITTER FROM THE POWER SOURCE BEFORE ADJUSTING OR
SERVICING THE MACHINE. IF YOU HAVE TO STOP TO REMOVE ANY DEBRIS FROM THE MACHINE,
ALWAYS RETRACT THE RAM AND UNPLUG THE MACHINE.
•
•
DO NOT MOVE OR REPOSITION THE WOOD SPLITTER WITH ITS MOTOR RUNNING.
DO NOT, UNDER ANY CONDITIONS, REMOVE, BEND, CUT, FIT, WELD, OR OTHERWISE ALTER
STANDARD PARTS ON THE DR 6 -TON ELECTRIC WOOD SPLITTER. MODIFICATIONS TO YOUR
MACHINE COULD CAUSE PERSONAL INJURIES AND WILL VOID YOUR WARRANTY.
•
•
•
WHILE USING THE DR 6 -TON ELECTRIC WOOD SPLITTER, DON'T HURRY OR TAKE THINGS FOR
GRANTED.
DO NOT OPERATE THE MACHINE WHEN UNDER THE INFLUENCE OF ALCOHOL, DRUGS, OR
MEDICATION.
USE THE MACHINE ONLY IN DAYLIGHT.
Safety for Children
TRAGIC ACCIDENTS CAN OCCUR IF THE OPERATOR IS NOT ALERT TO THE PRESENCE OF CHILDREN.
CHILDREN ARE OFTEN ATTRACTED TO THE WOOD SPLITTER AND THE SPLITTING ACTIVITY. NEVER
ASSUME THAT CHILDREN WILL REMAIN WHERE YOU LAST SAW THEM.
•
KEEP CHILDREN OUT OF THE SPLITTING AREA AND UNDER THE WATCHFUL CARE OF A
RESPONSIBLE ADULT.
•
•
BE ALERT AND TURN THE WOOD SPLITTER OFF IF CHILDREN ENTER THE WORK AREA.
NEVER ALLOW CHILDREN TO OPERATE THE DR 6 -TON ELECTRIC WOOD SPLITTER.
CALL TOLL FREE 1-800-DR-OWNER
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety with Electric-Powered Machines
NEVER OVERLOOK THE HAZARDS OF ELECTRICITY. ALWAYS FOLLOW THESE PRECAUTIONS:
•
NEVER OPEN THE SWITCH BOX OR MOTOR COVER. NEVER ATTEMPT ANY ELECTRICAL REPAIRS
YOURSELF. IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN OR CONTACT COUNTRY HOME
PRODUCTS’ TOLL-FREE SUPPORT AT 1-800-DR-OWNER (376-9637) FOR HELP OR INFORMATION.
•
•
•
NEVER OPERATE THE WOOD SPLITTER IF THERE IS AN ELECTRICAL HAZARD PRESENT.
NEVER OPERATE THE WOOD SPLITTER IN WET CONDITIONS.
NEVER OPERATE THE WOOD SPLITTER WITH A DAMAGED ELECTRICAL CORD OR DAMAGED
EXTENSION CORD.
•
•
NEVER PULL ON THE POWER CORD TO MOVE THE MACHINE.
ALWAYS GRASP THE POWER CORD PLUG WHEN UNPLUGGING THE CORD FROM THE OUTLET;
NEVER PULL THE PLUG OUT BY THE CORD.
•
NEVER OPERATE THE WOOD SPLITTER UNLESS THE POWER CORD IS PLUGGED INTO A PROPERLY
GROUNDED OUTLET, WHICH SUPPLIES 110-120V POWER, AND IS PROTECTED BY A 15-AMP CIRCUIT
BREAKER.
•
•
NEVER TAMPER WITH SAFETY DEVICES. CHECK THEIR PROPER OPERATION REGULARLY.
IF YOU WILL USE AN EXTENSION CORD, WE RECOMMEND THAT YOU KEEP THE CONNECTION
BETWEEN THE POWER CORD AND THE EXTENSION CORD WELL AWAY FROM ANY WATER.
•
•
NEVER USE AN EXTENSION CORD LONGER THAN 33 FEET OR SMALLER THAN 12 AWG IN DIAMETER,
BECAUSE THE CORD WILL PRODUCE A VOLTAGE DROP THAT WILL PREVENT THE MOTOR FROM
SUPPLYING FULL POWER AND MAY CAUSE DAMAGE TO THE MOTOR.
ALWAYS KEEP THE POWER CORD AND/OR EXTENSION CORD AWAY FROM EXCESSIVE HEAT, OIL,
AND SHARP OBJECTS.
Tip: Reference page 23 for Troubleshooting Tips.
6
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
Hydraulic Safety
ESCAPING PRESSURIZED FLUID FROM HYDRAULIC SYSTEM LEAKS CAN HAVE ENOUGH FORCE TO
PENETRATE SKIN AND CAUSE SERIOUS INJURY OR DEATH. HYDRAULIC FLUID CAN REMAIN
PRESSURIZED WHILE THE MOTOR IS OFF DUE TO THE RETURN SPRING FORCE ON THE RAM. ALWAYS
FOLLOW THESE PRECAUTIONS:
•
ALWAYS RELEASE RESIDUAL ENERGY FROM PRESSURIZED HYDRAULIC FLUID AND ALLOW THE FLUID
TO COOL BEFORE DOING ANY MAINTENANCE OR REPAIR WORK ON THE WOOD SPLITTER.
•
PLEASE FOLLOW THESE STEPS TO DEPRESSURIZE THE SYSTEM AND RELEASE RESIDUAL HYDRAULIC
ENERGY BEFORE STARTING ANY REPAIRS.
-
-
UNPLUG THE WOOD SPLITTER FROM THE POWER SOURCE.
MOVE THE OPERATING HANDLE DOWN AND UP FROM ONE LIMIT OF TRAVEL TO THE OTHER AT
LEAST FOUR TIMES. HOLD THE HANDLE FOR THREE SECONDS AT EACH LIMIT OF TRAVEL. THE
RAM SHOULD NOT MOVE DURING THE 4TH CYCLE AND SHOULD REMAIN FULLY RETRACTED.
-
CALL 1-800-DR-OWNER (376-9637), OR A QUALIFIED HYDRAULIC MECHANIC, FOR ASSISTANCE TO
REPLACE WORN COMPONENTS.
•
•
NEVER USE YOUR HAND OR ANY PART OF YOUR BODY TO CHECK FOR HYDRAULIC SYSTEM LEAKS
WHILE THE SYSTEM IS PRESSURIZED.
NEVER REMOVE THE FILL/DIPSTICK CAP FROM THE HYDRAULIC FLUID PORT WHILE THE MOTOR IS
RUNNING OR WHILE THE TANK IS STILL WARM AFTER THE MOTOR IS OFF. HOT PRESSURIZED FLUID
CAN CAUSE SERIOUS INJURY, SO WAIT FOR THE HYDRAULIC TANK TO COOL BEFORE REMOVING CAP.
•
•
THE WOOD SPLITTER MUST BE ON A LEVEL SURFACE.
PERIODICALLY CHECK FOR HYDRAULIC FLUID LEAKS BY PLACING A SHEET OF CARDBOARD UNDER
THE WOOD SPLITTER WHILE THE SYSTEM IS RUNNING.
•
•
GET PROFESSIONAL MEDICAL HELP AT ONCE IF HYDRAULIC OIL PENETRATES ANYONE'S SKIN.
NEVER ADJUST THE HYDRAULIC SYSTEM.
Tip: Reference page 23 for Troubleshooting Tips.
CALL TOLL FREE 1-800-DR-OWNER
7
Download from Www.Somanuals.com. All Manuals Search And Download.
THE WOOD SPLITTER MUST BE OPERATED SAFELY TO PREVENT OR MINIMIZE THE RISK OF MINOR OR
MODERATE INJURY. UNSAFE OPERATION CAN CREATE A NUMBER OF HAZARDS FOR YOU. ALWAYS
TAKE THE FOLLOWING PRECAUTIONS WHEN OPERATING THIS WOOD SPLITTER:
•
KEEP IN MIND THAT THE OPERATOR OR USER IS RESPONSIBLE FOR ACCIDENTS OR HAZARDS
OCCURRING TO OTHER PEOPLE, THEIR PROPERTY, AND THEMSELVES.
•
•
•
WEAR LONG PANTS WHILE SPLITTING WOOD.
ALWAYS CUT THE ENDS OF THE LOG YOU ARE SPLITTING AS SQUARELY AS POSSIBLE.
NEVER SPLIT MORE THAN ONE LOG AT A TIME UNLESS THE RAM HAS BEEN FULLY EXTENDED AND
A SECOND LOG IS NEEDED TO COMPLETE THE SPLIT OF THE FIRST LOG.
•
•
NEVER PUT ANYTHING BETWEEN THE LOG GUIDING PLATES AND THE SIDE OF A LOG; LOGS
SPREAD AS THEY ARE FORCED AGAINST THE WEDGE.
NEVER OPERATE THE RAM IN A STALLED POSITION FOR MORE THAN 5 SECONDS. THE HYDRAULIC
FLUID MAY OVERHEAT AND DAMAGE THE MACHINE. IF THE WOOD BEING SPLIT IS EXCESSIVELY
HARD, STOP THE MACHINE, ROTATE THE LOG 90° AND TRY AGAIN. IF YOU STILL CANNOT SPLIT
THE LOG, REJECT THE LOG AS IT EXCEEDS THE CAPACITY OF THE MACHINE.
•
•
NEVER LEAVE THE WOOD SPLITTER UNATTENDED. IF YOU LEAVE THE AREA, UNPLUG THE POWER
SOURCE.
CLEAN UP AS YOU WORK; ACCUMULATED SPLIT WOOD AND WOOD CHIPS CAN CREATE A
HAZARDOUS WORK ENVIRONMENT.
•
•
ALWAYS CHECK THE ALIGNMENT OF MOVING PARTS AND FOR DAMAGED OR WORN PARTS.
KEEP ALL NUTS AND BOLTS TIGHT AND KEEP THE EQUIPMENT AND ATTACHMENTS IN GOOD
OPERATING CONDITION.
•
ALWAYS CHECK THE POWER CABLE FOR DAMAGE PRIOR TO EVERY USE AND THAT IT IS FULLY
PROTECTED FROM DAMAGE FROM THE EQUIPMENT OR MATERIALS WHILE OPERATING THE
MACHINE.
•
•
SEE MANUFACTURER’S INSTRUCTIONS FOR PROPER OPERATION AND INSTALLATION OF
ACCESSORIES. ONLY USE ACCESSORIES APPROVED BY COUNTRY HOME PRODUCTS, INC.
NO LIST OF WARNINGS AND CAUTIONS CAN BE ALL-INCLUSIVE. IF SITUATIONS OCCUR THAT ARE
NOT COVERED BY THIS MANUAL, THE OPERATOR MUST APPLY COMMON SENSE AND OPERATE
THIS WOOD SPLITTER IN A SAFE MANNER. CALL 1-800-DR-OWNER (376-9637) FOR ASSISTANCE.
Additional Information and Potential Changes
Country Home Products, Inc. reserves the right to discontinue, change, and improve its products at any
time without notice or obligation to the purchaser. The descriptions and specifications contained in this
manual were in effect at printing. Equipment described within this manual may be optional. Some
illustrations may not be applicable to your machine.
8
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3
UNPACKING AND ASSEMBLING YOUR DR 6 -TON
ELECTRIC WOOD SPLITTER
This chapter outlines a few simple steps you will need to follow to unpack and assemble your new machine
before you use it. Familiarize yourself with the controls and features on your new wood splitter by reviewing
Figure 1 on page 10 before beginning the steps outlined in this chapter. If you have any questions at all,
please feel free to contact our Technical Support Representatives at our toll free number:
1-800-DR-OWNER (376-9637).
CALL TOLL FREE 1-800-DR-OWNER
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DR 6 -TON ELECTRIC WOOD SPLITTER Controls and Features
NOTE: The model shown in Figure 1 may look slightly different from your machine.
Ram
Log Guides
Operating Handle
Wedge
Operating Label
Rear Lifting
Safety Label
Handle
Air Bleed Screw
Power
Cord
Reset Button
Oil Pump
Assembly
Dip Stick/
Hydraulic
Fluid Port
Controls Label
Electric Motor Assembly
Attachment Hole*
Electric Motor On-Off Switch
Air Bleed Screw Label
Wheels
Electric Motor Shroud
Front Lifting Handle
Front Support Leg
Assembly
*The hole provided is for the Safety J-Hook supplied
with the Optional Stand. See page 28.
Figure 1
10
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking and Assembling the DR 6 -TON ELECTRIC WOOD SPLITTER
NOTE: Read this Safety & Operating Instructions Manual before using your new DR 6 -TON ELECTRIC
WOOD SPLITTER. The wood splitter shipped from the factory fully assembled with the exception of
the Wheels and the Operation Handle. The following instructions will detail how to unpack and
assemble the machine.
Tools and Parts Supplied:
•
•
•
•
6mm Hex Wrench
10 - 12mm Wrench
13 - 16mm Wrench
Operating Handle w/
Retaining Bolt and Washer
•
•
•
(2) 6mm Bolts
Extra Hydraulic Seal
(2) Wheels
Additional Tool Required:
Knife
•
STABILIZE THE SHIPPING CONTAINER ON A FLAT SURFACE BEFORE ATTEMPTING TO UNPACK AND
ASSEMBLE THE MACHINE.
1. With the help of another person (the machine weighs 171
Bottom of carton
pounds), carefully roll the shipping carton over onto its top.
2. Carefully cut the tape along the bottom seam of the shipping
carton with a knife, open the carton, and remove the Wheel from
the packing; setting it aside (Figure 2).
3. Now, carefully roll the shipping carton back onto its bottom
(Figure 3) and lift the shipping carton off your new DR 6 -TON
ELECTRIC WOOD SPLITTER (Figure 4). The machine should
now be resting on the Front Support Legs and the Rear Support.
Figure 2
4. Remove the second Wheel from the packing (setting it aside)
and any remaining packing materials from the machine. Do not
discard your packaging material until you are fully satisfied with
your new DR 6 -TON ELECTRIC WOOD SPLITTER.
Top of carton
Lift carton up
Figure 4
Figure 3
CALL TOLL FREE 1-800-DR-OWNER
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Wrap the Power Cord around the Power Cord
Keeper (Figure 5).
Power Cord
Keeper
6. Insert a Wheel Axle all the way into the hole at the
rear of the frame (Figure 6) and install a 6mm Bolt
(Figure 7). Tighten the Bolt with the 10mm
Wrench (Figure 7).
7. Repeat step 5 for the other rear Wheel on the
opposite side of the machine.
8. Remove the Operating Handle Retaining Screw
and Washer from the end of the Handle Shaft.
Figure 5
9. Insert the Operating Handle Shaft into the
recessed hole on top of the cylindrical shaft
protruding from the right rear side of the machine.
Thread the Retaining Bolt with Washer up through
the hole in the bottom of the cylindrical shaft and
into the Operating Handle shaft (Figure 8).
10. While holding the Operating Handle Grip tight
with the flat surface of the Operating Handle Grip
facing forward, tighten the Retaining Bolt using the
6mm Hex Wrench (Figure 8).
Flat surface facing forward
Figure 6
Figure 7
Figure 8
BEFORE ATTEMPTING TO OPERATE YOUR NEW DR 6 -TON ELECTRIC WOOD SPLITTER, READ THE SECTION
TITLED “BEFORE STARTING THE ELECTRIC MOTOR” ON PAGE 13 IN THE SAFETY & OPERATING
INSTRUCTIONS MANUAL.
If you have questions, please call one of our Technical Support Representatives TOLL-FREE:
1-800-DR-OWNER (376-9637).
12
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4
OPERATING YOUR DR 6 -TON ELECTRIC WOOD SPLITTER
This chapter covers the procedures for operating your new DR 6 -TON ELECTRIC WOOD SPLITTER and
discusses basic operation features. You may find it helpful to review the Controls and Features on page 10.
Before Starting the Electric Motor
Tools Needed:
•
•
6mm Hex Wrench
#3 Phillips Screwdriver
1. Inspect the area in which you will be working.
•
•
Place the wood splitter only on a firm, level, supported surface 2 to 3 feet above the ground.
NEVER operate the wood splitter on the ground as there is risk of injury and would not be
comfortable for the operator while in use.
•
The site must be free of slippery surfaces and potentially hazardous obstacles. Also, make sure
there won't be people or animals within a six-foot radius around the wood splitter.
2. Plan your work before you start.
•
•
•
Have the logs that you are splitting positioned where you can easily reach them. Remember, the
maximum log length is 20" and the maximum diameter is 16" for this wood splitter.
Split only dry, seasoned logs as they will split more easily than green logs. Green logs may stick
on the wedge and jam the wood splitter.
Have a site located where the split wood can be stacked or loaded onto a truck or nearby carrier.
•
•
ALWAYS MAKE CERTAIN THAT THE MACHINE IS ON A FIRM LEVEL SURFACE.
IT IS IMPORTANT THAT THE AIR BLEED SCREW IS OPEN WHEN YOU USE THE MACHINE. YOU
WILL NEED A #3 PHILLIPS SCREWDRIVER TO MAKE THIS ADJUSTMENT (FIGURE 9).
•
USE CARE, DO NOT OVER TIGHTEN AND STRIP THE AIR BLEED SCREW THREADS.
3. Prior to using the wood splitter, open the Air Bleed Screw
by turning it counter-clockwise four (4) times. Leave the Air
Bleed Screw open in this position while using the machine.
Air Bleed
We recommend closing the Air Bleed Screw after each use,
but you can leave the Air Bleed Screw open when you are
finished, unless you are going to transport the machine, at
which time you should close the Air Bleed Screw being
careful not to over tighten and strip the screw.
Figure 9
CALL TOLL FREE 1-800-DR-OWNER
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Connect the electric cord from the wood splitter to a standard electrical, 110-120VAC, grounded
power source fused at 15 AMPS. If using an extension cord, it must be 12AWG and less than 33
feet long with a rating of 15 AMPS. Route the cord from the wood splitter to the power source in
such a way that safeguards against damaging the cord during the wood splitting session. Be sure
to avoid wet conditions.
5. Turn ON the Motor, then cycle the Ram several times using the Operating Handle. After cycling, if
the Ram does not travel to within 5" of the wedge, proceed to steps 6 through 8.
6. Check the hydraulic fluid level by tipping the machine up on the Wheels and Rear Handle. Clean
the area around the Hydraulic Fluid Fill/Drain Port (Figure 10) and then, using the 6mm Hex
Wrench provided, unscrew the Dipstick located in the Hydraulic Fluid Fill/Drain Port.
7. Clean the Dipstick and check the level (do not screw the Dipstick down when checking); it should
be between the two marks on the Dipstick. If the fluid is too high, simply pour out a little at a time
into a suitable container by tilting the wood splitter. If the fluid is too low, add an AW32 hydraulic
fluid, a little at a time until the level falls between the two marks on the dipstick.
8. Clean the Dipstick and the O-ring seal thoroughly and reinstall being careful not to damage the
threads of the aluminum Hydraulic Fluid Cylinder End Cover.
Tip: In cold weather, cycle the Ram to warm-up the hydraulic fluid. This will provide full power from your
DR 6 -TON ELECTRIC WOOD SPLITTER.
Dipstick and Hydraulic Fluid Port
Figure 10
14
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
Splitting Safety
The DR 6 -TON ELECTRIC WOOD SPLITTER has a Ram with 6 tons of force.
•
ALWAYS BE SURE TO STAND INSIDE THE OPERATOR ZONE WHEN OPERATING THE WOOD SPLITTER
(FIGURE 11). THIS IS THE AREA DIRECTLY BEHIND YOUR DR 6 -TON ELECTRIC WOOD SPLITTER.
NEVER OPERATE THE WOOD SPLITTER FROM ANYWHERE ELSE.
•
•
HANDLE LOGS ONLY FROM THE SIDES, NEVER BY THE ENDS.
FOR BEST SPLITTING RESULTS, PLACE LOG FLAT ON THE BEAM BETWEEN THE LOG GUIDES WITH
BUTT END AGAINST THE LEADING EDGE OF THE WEDGE (FIGURE 11).
•
•
•
•
NEVER ATTEMPT TO SPLIT A LOG AT AN ANGLE AND BE SURE THE WEDGE AND RAM WILL CONTACT
THE LOG SQUARELY ON THE ENDS.
BE VERY CAREFUL TO KEEP ARMS AND FINGERS AWAY FROM THE WEDGE, RAM, AND SPLITTING
AREA.
KEEP HANDS AND FINGERS CLEAR AT ALL TIMES. MANY WOOD SPLITTING ACCIDENTS HAPPEN ON
THE RETURN PORTION OF THE STROKE.
DO NOT PUT ANY PART OF YOUR BODY WITHIN THE SPLITTING AREA. USE A STICK IF YOU NEED
TO REMOVE DEBRIS FROM THE SPLITTING AREA (FIGURE 11).
Ram
Operator Zone
Splitting Area
Wedge
Operator Zone
Figure 11
CALL TOLL FREE 1-800-DR-OWNER
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the DR 6 -TON ELECTRIC WOOD SPLITTER
NOTE 1: The hydraulic control is a single handle valve called the Operating Handle. With the Electric Motor
Control Switch is ON, the ram travels forward when you push the Operating Handle forward. The
cylinder will retract when you release the Operating Handle.
NOTE 2: Before starting the splitting operation, the log Ram should be cycled 3 to 4 times back and forth (with
the Air Bleed Screw open). This will remove any air that may have mixed into the hydraulic fluid from
shipping and handling. See Step 3 on page 13 for the Air Bleed Screw Operation.
Tip: In cold weather, cycle the Ram to warm-up the hydraulic fluid. This will provide full power from your
DR 6 -TON ELECTRIC WOOD SPLITTER.
1. With a log properly loaded, and with the Air Bleed Screw open, turn ON the Electric Motor and wait
a few seconds as the motor creates pressure in the hydraulic pump.
NOTE: If the Electric Motor does not start, try pushing in the Reset Button (Figure 1 on page 10).
2. Push the Operating Handle forward. The Ram will now compress the log against the wedge,
splitting the log.
NOTE: The design of the DR 6 -TON ELECTRIC WOOD SPLITTER is to run at two (2) different speeds.
When you push the Operating Handle fully forward, the Ram will run at a slower speed but have
more power. When you push the Operating Handle half way, the Ram will run at a faster speed, but
the machine will have less splitting power. We recommend running the Ram at the higher speed
until it engages the log. You should then push the Operator Handle fully forward and run the Ram
at the slower speed to split the log; this will deliver the most power.
3. Keep holding the Operating Handle forward until the split pieces of the log fall away or the Ram has
reached the end of its stroke. When you have finished splitting a log, release the Operator Handle.
The Ram will retract to its start position.
MAKE SURE NOTHING WILL INTERFERE WITH THE RAM WHILE IT RETRACTS.
IF THE LOG DOES NOT SPLIT IMMEDIATELY, DO NOT CONTINUE THE FORWARD THRUST OF THE
RAM FOR MORE THAN 5 SECONDS. THIS CAN DAMAGE THE SPLITTER. AFTER THE RAM HAS
RETRACTED, TRY REPOSITIONING THE LOG ON THE SPLITTER OR SET THE LOG ASIDE.
4. Stack the split wood as you work. This will provide a safer work area by keeping it uncluttered, avoiding
the danger of tripping or damaging the power cord.
16
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Free a Jammed Log from the Wedge
•
•
•
NEVER PLACE YOUR HANDS NEAR THE LOG WHEN ATTEMPTING TO FREE IT FROM THE WEDGE.
NEVER ASK FOR THE ASSISTANCE OF ANOTHER PERSON WHEN FREEING A JAMMED LOG.
NEVER TRY TO EXTRACT THE JAMMED LOG BY HITTING IT WITH A TOOL; THIS COULD DAMAGE THE
MACHINE.
1. Release the Operator Handle so that the Ram fully retracts
(Figure 12).
2. Insert a plastic or wooden Wedge under the jammed log
(Figure 12) and activate the Ram to push the Wedge under
the jammed log.
Wedge
3. Repeat this process, using progressively larger Wedges,
until the jammed log is free (Figure 12).
4. Lift the log off the wood splitter Wedge after loosening.
Figure 12
CALL TOLL FREE 1-800-DR-OWNER
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5
MAINTAINING THE DR 6 -TON ELECTRIC WOOD SPLITTER
This chapter covers regular maintenance procedures that will ensure the best performance and long life of
your wood splitter.
•
•
BEFORE PERFORMING ANY MAINTENANCE, YOU MUST UNPLUG THE WOOD SPLITTER FROM THE
POWER SOURCE.
MAKE SURE THE HYDRAULIC SYSTEM IS DEPRESSURIZED (SEE PAGE 7), AND MAKE SURE THE FLUID
HAS COOLED. READ THE "GENERAL SAFETY RULES" (CHAPTER 2) OF THIS MANUAL BEFORE
PERFORMING ANY REPAIRS OR MAINTENANCE.
Regular Maintenance Checklist before each use
•
•
•
•
•
•
Clean the log Ram and Guides.
Check the Splitting Wedge for sharpness (page 20).
Check the general condition of the Wood Splitter, e.g.; nuts, bolts, welds (etc).
Check that the Electric Motor Shroud is free of accumulated debris (Figure 13).
Check the Ram for smooth travel.
Check the condition of the electrical cord.
Shroud
Figure 13
Before each season
•
Check the hydraulic fluid level (page 20). Use AW32 hydraulic fluid for operation over 40°F and
Dexron® automatic transmission fluid for operation below 40°F.
NEVER DRAIN THE HYDRAULIC FLUID. JUST ADD ENOUGH TO REPLENISH THE LOST VOLUME.
CALL TOLL FREE 1-800-DR-OWNER
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Hydraulic Fluid Level
NOTE: Adjust the hydraulic fluid level only if a problem suggests that the level is off; otherwise, just check the level
every few months.
•
•
BEFORE PERFORMING ANY MAINTENANCE, YOU MUST UNPLUG THE WOOD SPLITTER FROM THE
POWER SOURCE. MAKE SURE THE HYDRAULIC SYSTEM IS DEPRESSURIZED (SEE PAGE 7), AND MAKE
SURE THE FLUID HAS COOLED.
READ THE "GENERAL SAFETY RULES" (CHAPTER 2) OF THIS MANUAL BEFORE PERFORMING ANY
REPAIRS OR MAINTENANCE.
Tools Needed:
•
•
6mm Hex Wrench (Provided)
#3 Phillips Screwdriver
1. Depressurize the hydraulic system; see page 7.
2. Check the hydraulic fluid level by tipping the wood splitter up on the Wheels and Rear Handle.
3. Clean the area around the Hydraulic Fluid Fill/Drain Port. It is important not to let any debris enter
the fluid reservoir; see Figure 10 on page 14. Loosen the Air Bleed Screw and then, using the 6mm
Hex Wrench provided, unscrew the Dipstick located in the Hydraulic Fluid Fill/Drain Port.
4. Clean the Dipstick and replace without screwing down to check the level; it should be between the
two marks on the Dipstick. If the fluid is too high, simply pour out a little at a time into a suitable
container by tilting the wood splitter. If the fluid is too low, add AW32 hydraulic fluid, a little at a
time, until the level falls between the two marks on the Dipstick.
5. Clean the Dipstick and the O-ring seal thoroughly and reinstall, being careful not to damage the
threads of the aluminum Hydraulic Fluid Cylinder End Cover.
6. Cycle the Ram back and forth 3 or 4 times to purge any air from the hydraulic system; see Figure 9
on page 13.
Sharpening the Wedge
•
•
BEFORE PERFORMING ANY MAINTENANCE, YOU MUST UNPLUG THE WOOD SPLITTER FROM THE
POWER SOURCE. MAKE SURE THE HYDRAULIC SYSTEM IS DEPRESSURIZED (SEE PAGE 7), AND MAKE
SURE THE FLUID HAS COOLED.
READ THE "GENERAL SAFETY RULES" (CHAPTER 2) OF THIS MANUAL BEFORE PERFORMING ANY
REPAIRS OR MAINTENANCE.
Tool Needed:
•
Fine-Toothed Flat File
Before each splitting session, check the sharpness of the Wedge. As required, remove any burrs or flat
spots on the Wedge using a fine-toothed flat file.
20
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
THE DR 6 -TON ELECTRIC WOOD SPLITTER MUST BE CONNECTED TO A PROPERLY GROUNDED OUTLET
BEFORE OPERATION.
End of Season and Storage
•
•
BEFORE PERFORMING ANY MAINTENANCE, YOU MUST UNPLUG THE WOOD SPLITTER FROM THE
POWER SOURCE. MAKE SURE THE HYDRAULIC SYSTEM IS DEPRESSURIZED (SEE PAGE 7), AND MAKE
SURE THE FLUID HAS COOLED.
READ THE "GENERAL SAFETY RULES" (CHAPTER 2) OF THIS MANUAL BEFORE PERFORMING ANY
REPAIRS OR MAINTENANCE.
•
•
Wipe down the wood splitter to remove any moisture, wood chips, and dirt that may have
accumulated on the Log Guide Rails and Hydraulic Control.
Clean out any accumulated debris from the Electric Motor Shroud (Figure 13 on page 19) and the
Motor Fan Housing.
•
•
•
Apply a thin coating of oil or #2 Lithium Grease to the Wedge Cutting Edge to prevent rust.
Store the DR 6 -TON ELECTRIC WOOD SPLITTER in a dry area.
Relieve any internal air pressure by opening the Air Bleed Screw by turning counter-clockwise 4
times and then retighten by turning clockwise prior to storing the machine; see Figure 9 on page
13. DO NOT OVER TIGHTEN!
USE CARE, DO NOT OVER TIGHTEN, AND STRIP THE AIR BLEED SCREW THREADS.
CALL TOLL FREE 1-800-DR-OWNER
21
Download from Www.Somanuals.com. All Manuals Search And Download.
22
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6
TROUBLESHOOTING
Consult the Troubleshooting Table below for common problems and their solutions. If you continue to
experience problems, call our Technical Support Representatives at 1-800-DR-OWNER.
Troubleshooting Table
•
•
BEFORE PERFORMING ANY MAINTENANCE, YOU MUST UNPLUG THE WOOD SPLITTER FROM THE
POWER SOURCE. MAKE SURE THE HYDRAULIC SYSTEM IS DEPRESSURIZED (SEE PAGE 7), AND MAKE
SURE THE FLUID HAS COOLED.
READ THE "GENERAL SAFETY RULES" (CHAPTER 2) OF THIS MANUAL BEFORE PERFORMING ANY
REPAIRS OR MAINTENANCE.
SYMPTOM
POSSIBLE CAUSE
Ram will not move
or is slow to
respond.
⇒ The Air Bleed Screw may be open. See page 13, Step 3.
⇒ The motor Reset has tripped; push the Reset Button. See Figure 1 on page 10.
⇒ Bleed any accumulated air from the hydraulic system. See page 20, step 5.
⇒ The wood splitter may not be on a level surface. See page 13, step 1.
⇒ Make sure the voltage at the outlet or extension cord connection to the wood splitter
is at least 105VAC.
⇒ If you are using an extension cord, make sure that the cord is less than 33 feet long
and is not smaller than 12 AWG wire.
⇒ The hydraulic fluid may be low. Check and adjust the level as required; see page 20.
⇒ In extreme high temperature and heavy rapid use, the hydraulic fluid may have over
heated. Allow the machine to cool.
⇒ The wood you are splitting may be too hard, it has knots, or its fiber is very tough.
⇒ Check the possible causes for the previous Ram operation symptom.
Log fails to split.
⇒ Incorrect positioning of the log; re-position the log flat on the splitting beam with
the ends squarely against the Ram face and Splitting Wedge.
⇒ Log exceeds permitted dimensions or the wood is too hard for the capacity of the
machine. The maximum log length is 20" with a maximum diameter of 16" for the
DR 6 -TON ELECTRIC WOOD SPLITTER.
⇒ The wedge has burrs or nicks and needs to be sharpening; see page 20.
⇒ There may be a hydraulic fluid leak. Locate the leak using a piece of cardboard
under the machine and call 1-800-DR-OWNER (376-9637), or a qualified hydraulic
mechanic for assistance, to replace worn components.
⇒ Hydraulic pressure is too low. Call 1-800-DR-OWNER (376-9637), or a qualified
hydraulic mechanic for assistance to replace worn components.
CALL TOLL FREE 1-800-DR-OWNER
23
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
BEFORE PERFORMING ANY MAINTENANCE, YOU MUST UNPLUG THE WOOD SPLITTER FROM THE
POWER SOURCE. MAKE SURE THE HYDRAULIC SYSTEM IS DEPRESSURIZED (SEE PAGE 7), AND MAKE
SURE THE FLUID HAS COOLED.
READ THE "GENERAL SAFETY RULES" (CHAPTER 2) OF THIS MANUAL BEFORE PERFORMING ANY
REPAIRS OR MAINTENANCE.
SYMPTOM
POSSIBLE CAUSE
Ram advances with
a jerky motion or
with strong
⇒ Check the possible causes for the Ram operation symptom on the previous page.
⇒ Check the hydraulic fluid level; see page 20.
vibrations.
⇒ Bleed any accumulated air from the hydraulic system. See page 20, Step 5. If the
problem persists, call 1-800-DR-OWNER (376-9637) for assistance.
Hydraulic fluid
leaking from the Air
Bleed Screw.
⇒ The wood splitter may not be on a level surface. See page 13, step 1.
Hydraulic fluid
leaking from the
Ram or other
⇒ Check that the Air Bleed Screw is tight before moving the machine. Use care: Do
not over tighten and strip the Air Bleed Screw Threads.
⇒ The hydraulic fluid seals may be worn. Call 1-800-DR-OWNER (376-9637), or a
external parts.
qualified hydraulic mechanic for assistance to replace worn components.
24
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 7
PARTS LISTS, SCHEMATIC DIAGRAMS AND WARRANTY
Parts List - DR 6 -TON ELECTRIC WOOD SPLITTER
NOTE: Part numbers listed are available through Country Home Products, Inc.
Ref# Part#
Hardware :
Description
Ref# Part#
Description
27 220201 Front Leg
01 220511 Nut, Hex, M16
29 220181 Main Body Weldment
30 220191 Ram & Tie Rod Weldment
31 220221 Cover, Left
02 220521 Nut, Hex, M16 (Thin)
04 220601 Retaining Ring, External, 38mm
06 220591 Sleeve, Rod, 38mm ID,50mm L
23 219611 Bolt, Hex Head, M8 x 16
24 219621 Washer, Flat, M8
38 220211 Cover, Right
41 220321 Filter, Screen, Brass
44 220301 Cover, Rear End, 105mm W, 154mm H
47 220311 Shaft, Handle/Valve, Plated
54 220231 Rear Cover Weldment
56 220351 Bracket, Power Cord
82 220241 Motor Shroud Weldment
28 219991 Cap
32 220001 Cap, Plastic, 20mm
33 219861 Bolt, Hex Head, M8 x 10
35 219851 Bolt, Socket Head, M6 x 14
36 219951 Washer, Flat, M6
113 220281 Spring, Compression, 66mm OD,
700mm L
40 219941 Washer, flat, M3
43 220571 Spring, Torsion, 30mm ID
45 219651 Bolt, Socket Head, M8 x 14
46 219961 Washer, Spring, M8
49 220561 Washer, Flat, Copper, M12
50 220541 Nut, Hex, M12
Electrical Components :
39 219831 Screw, Cross Head, ST3.2 x 14mm
coarse
61 215361 Wire, Switch
62 215401 Wire Bushing, 20mm
63 215411 Wire Bushing Nut, 20mm
57 220551 Washer, Flat, M12
69 215341 Seal, Electrical Box, rubber,
135mm W x 105mm H
70 215331 Box, Electrical,
58 220531 Nut, Hex, Acorn, Plated, M12
115 219871 Bolt, Hex Head, M8 x 25
116 220691 Bolt, Socket Head, M8 x 14
117 220581 Circlip, Spindle , 38mm
136mm W x 106mm H x 45mm D
72 215351 Pushbutton, Reset, L2, 15A
73 215381 Switch, Rocker, HY 12-9
74 215371 Block, Wire Terminal
75 215391 Capacitor, 60uF, 300V
Components :
03 220261 Rod, Piston, 38mm OD
05 220611 Spring, 40mm ID, 100mm L
07 220331 Dipstick, M14
13 220291 Cover, Front End, w/Rod Hole,
101mm W x 150mm H
109 215421 Power Cord Kit:
62 215401 Wire Bushing, 20mm
63 215411 Wire Bushing Nut, 20mm
66 215431 Cord, 110V, 6' L
15 221011 Stud, M10 x 881mm
16 220341 Tube, Return,
12mm OD, 9.5mm ID, 810mm L
67 219841 Screw, Cross Head, M5 x 10
19 220271 Piston, Alum., 69.5mm OD, 25.0mm L
22 220251 Main Cylinder,
78mm OD, 70mm ID, 788mm L
68 215441 Plate, Bushing, Cord,
50mm OD, 21mm ID
CALL TOLL FREE 1-800-DR-OWNER
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref# Part#
Description
Ref# Part#
Description
107 215451 Motor Pump Kit:
102 219691 Bleed Screw Kit:
24 219621 Washer, Flat, M8
60 215491 O-Ring, Rubber, 15.5mm OD,
10.5mm ID
11 219701 Screw, Bleed, Cross Head,
M6 x 10, Plated
12 219711 Washer, Flat, Nylon, 12mm OD,
5.8Imm D, 1.75mm THK
64 215481 Bolt, Hex Head, M8 x 30
65 215461 Motor, Pump, Connection Box,
w/out Fan Kit
71 215471 Pad, Motor Mounting, Rubber
83 219881 Bolt, Hex Head, M8 x 35
105 220401 Slide Pad Kit:
37 220411 Pad, Slide, Plastic, Flat,
100mm W, 102mm L
114 220421 Pad, Slide, Plastic, V,
100mm W, 102mm L
108 215501 Fan Kit:
76 215541 Screw, Cross Head, M4 x 8
77 215551 Washer, Spring, M4
78 215561 Washer, Flat, M4
220431 Seal Kit :
08 220451 Seal, Ring, Teflon, 38mm ID
09 220491 Seal, UHS, 38mm ID
79 215521 Fan, 12 Blade, Motor,
138mm OD, 20mm ID
10 220501 O-Ring, Rubber,
71mm OD, 65mm ID
80 215531 Circlip, External, 19mm ID
81 215511 Cover, Fan, 155mm OD, 75mm L
14 220441 Gasket, 150mm x 104mm
17 219771 O-Ring, Rubber, 2.65 - 10.6mm
18 220461 O-Ring, Rubber, 2.65 - 32.5mm
20 220471 O-Ring, Rubber, 3.5 - 58
21 220481 Seal, Piston, Square, 70mm OD,
65mm ID, 4mm L
110 220361 Wheel Kit:
51 219551 Shaft, Wheel,
14.8mm OD, 93.5mm L
52 220371 Wheel, Molded,7 Spoke,
6.5" OD, 2" Width
111 220621 Product Pack:
53 219561 Ring, Retaining, External, 14mm
59 219571 Bolt, Hex Head, M6 x 12
90 220091 Wrench, Allen Key, M6
91 220071 Wrench 13 - 16mm
92 220081 Wrench 10 - 12mm
93 220101 Seal, Washer, Dipstick, M14
101 214591 WDS 6.4 S&O Manual
103 220381 Carry Handle Kit:
23 219611 Bolt, Hex Head, M8 x 16
24 219621 Washer, Flat, M8
55 219591 Handle, Rubber,
35mm OD, 120mm W, M8
112 220391 Handle, Rubber,
35mm OD, 215mm W, M8
Labels:
94 212861 Label, Operating
95 211981 Label, Controls
96 206861 Label, Air Bleed Screw
97 193521A Label, Serial Number
98 212871A Label, Branding, Right Side
99 212881A Label, Branding, Left Side
100 211891 Label, Safety - Warning
106 219631 Operating Handle Kit:
45 219651 Bolt, Socket Head, M8 x 14
46 219961 Washer, Spring, M8
48 219641 Handle Arm w/Grip, Plated,
13mm OD, 143mm L, M8
Packaging :
104 219661 Rubber Foot Kit:
25 219671 Foot, Rubber,
25mm OD, 16mm H, M8
84 220631 Packing, Foam, A
85 220641 Packing, Foam, B
86 220651 Packing, Foam, C
87 220661 Packing, Foam, D
88 220671 Packing, Foam, E
26 219681 Nut, Hex, M8
89 220681 Carton, Shipping, 1100mm L,
335mm W, 580mm H
26
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
Schematic - DR 6 -TON ELECTRIC WOOD SPLITTER
WDS 6.4
060602
CALL TOLL FREE 1-800-DR-OWNER
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
The following three (3) Optional Accessories are available for your DR 6-Ton Electric Wood Splitter
through Country Home Products, Inc. by calling Toll-Free: 1-800-DR-OWNER (376-9637). Please refer to
the Optional Accessories Safety & Operating Instructions Manual supplied with each accessory for the
proper installation and use.
Tray
Table
Storage Clamp
Notes
28
DR® WDS 6.4, 6 -TON ELECTRIC WOOD SPLITTER
Download from Www.Somanuals.com. All Manuals Search And Download.
DR® 6 -TON ELECTRIC WOOD SPLITTER
2-Year Limited Warranty
Terms and Conditions
The DR® 6 -TON ELECTRIC WOOD SPLITTER is warranted for two (2) years against defects in materials or workmanship when
put to ordinary and normal consumer use; ninety (90) days for any other use.
For the purposes of all the above warranties, “ordinary and normal consumer use” refers to non-commercial residential use and
does not include misuse, accidents, or damage due to inadequate maintenance.
Country Home Products, Inc. (home of DR® Power Equipment) certifies that the DR® 6 -TON ELECTRIC WOOD SPLITTER is fit
for ordinary purposes for which a product of this type is used. Country Home Products, Inc. however, limits the implied
warranties of merchantability and fitness in duration to a period of two (2) years in consumer use, ninety (90) days for any other
use.
The 2-Year Limited Warranty on the DR® 6 -TON ELECTRIC WOOD SPLITTER starts on the date the machine ships from our
factory. The 2-Year Limited Warranty is applicable only to the original owner.
The warranty holder is responsible for the performance of the required maintenance as defined by the manufacturer's owner's manual.
The warranty holder is responsible for replacement of normally wearing parts such as the plastic slide pads. Attachments and
accessories to the machine are not covered by this warranty.
During the warranty period, the warranty holder is responsible for the machine transportation charges, if required. During the warranty
period, warranty parts will ship by standard method at no charge to the warranty holder. Expedited shipping of warranty parts is the
responsibility of the warranty holder.
SOME STATES DO NOT ALLOW LIMITATIONS ON THE LENGTH OF IMPLIED WARRANTIES, SO THE ABOVE LIMITATIONS MAY
NOT APPLY TO YOU.
Country Home Products, Inc. shall not be liable under any circumstances for any incidental or consequential damages or
expenses of any kind, including, but not limited to, cost of equipment rentals, loss of profit, or cost of hiring services to perform
tasks normally performed by the DR® 6 -TON ELECTRIC WOOD SPLITTER.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
Customer Service Hotline
Country Home Products, Inc.’s objective is to have 100% satisfied customers. For that reason, we operate a 6-day-a-week
Technical Service Department for our Owners. You can access a Representative by dialing our TOLL-FREE Hotline at 1-800-DR-
OWNER (376-9637). The sole job of our well-trained and friendly folks is to ensure that you get any help you need in a timely
fashion. They are there to answer all your questions including: (1) inquiries on any of the above warranties, (2) inquiries about
replacement parts, or (3) your questions regarding service, maintenance, and operation.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Daily Checklist for the DR 6 -TON ELECTRIC WOOD SPLITTER
To help maintain your DR 6 -TON ELECTRIC WOOD SPLITTER for optimum performance, we recommend
you follow this checklist each time you use your machine.
[ ] HARDWARE: Check all nuts and bolts to be sure that the components are secure.
[ ] FRAME: Check all welds to be sure that the frame is in tact and secure.
[ ] CLEAN: Make sure that the log guides and the top of the wood splitter beam are clean. Check that
the Electric Motor Shroud is free of accumulated debris (Figure 13 on page 19).
[ ] AIR BLEED SCREW: Make sure to open the Air Bleed Screw prior to operating the wood splitter;
see page 13.
COUNTRY HOME PRODUCTS, Inc.
M E I G S R O A D , P . O . B O X 2 5 , V E R G E N N E S , V E R M O N T 0 5 4 9 1
©2006 CHP, Inc. 214591
Download from Www.Somanuals.com. All Manuals Search And Download.
|