1.888.227.2178
Table of Contents
To register your fan, please visit:
What to Expect with
Your Installation
Tools Needed
Mounting Options
Ceiling Bracket
Save your receipt for proof of purchase.
Congratulations on purchasing your new Casablanca®
ceiling fan! It will provide comfort and performance in
your home or office for many years. This installation and
operation manual contains complete instructions for
installing and operating your fan.
30 inches
4
2
3
5
We are proud of our work and
appreciate the opportunity
to supply you with the best
Decorative Arms
Downrod
Wiring
Canopy
Wall Control
ceiling fan available anywhere
in the world.
6
7
10
18
12
13
Maintenance
& Cleaning
Blades
Switch Housing
Light Kit
Operation
Troubleshooting
?
?
?
14
15
16
20
21
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Tools Needed
Pliers
Wire Strippers
Screwdrivers
Ladder
9/64” Drill Bit
(optional)
Power Drill
(optional)
Allen Wrench
(included)
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
O
34
CEILING
1.888.227.2178
Mounting Options
If you have a flat ceiling:
Hang your fan by a standard downrod (included).
Standard
Mounting
Support
Structure
Support
Structure
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
1. You will need a longer downrod (sold separately).
Angled
Mounting
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Ceiling
Angled
(required)
Standard
Mounting
Style
Outlet Box
Mounting
Style
Use the three steps below to determine if your ceiling angle is greater than 34°
1
2
3
34°
PLACE
SLIDE
toward ceiling
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
Guide Touches
but NOT Ceiling
Wall
Use Standard Mounting
to hang the fan from a flat ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
You need BOTH
a Longer
You need ONLY
a Longer
Downrod &
an Angled
Downrod
Mounting Kit
*most common
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Ceiling Bracket
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
to support structure with
(provided with outlet
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
If you are unable to do this,
call Technical Support at
1-888-227-2178.
still attached.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Refer to warning w.1 on pg. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Decorative Arms
Screw
Holes
Align the screw holes on the decorative arms
with the screw holes on the side of the fan.
Install both decorative arms to the
decorative cup using decorative arm screws
found in the hardware bag.
Install the decorative screws through the holes
in the decorative arms into the fan. HAND
TIGHTEN to avoid damaging the finish.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Downrod
Standard
skip to next page
Downrod
for ceilings 8-10’ high
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
1
2
3
4
5
10
9
8
7
6
Steps 6-10 to reassemble with new pipe
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Thread the downrod through
the decorative arm cup and
into the fan. Hand tighten the
downrod (at least 4-5 full turns)
until it stops.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
8”
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Put the wires and downrod through the canopy.
Let the canopy sit loosely on top of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Wiring
Note: To connect the wires, hold
the bare metal leads together and
place a wire connector over them,
then twist clockwise until tight.
C
Receiver
Using an orange wire connector
from the hardware bag:
Connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and ceiling bracket.
green/yellow stripe
Place the receiver on top of the downrod
assembly as shown.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Wiring (continued)
C
Using the orange wire connectors
from the remote control hardware bag:
Using the orange wire connectors
from the hardware bag:
•
Connect the yellow wire from
the receiver to the black wire
from the fan.
•
Connect the black (ungrounded)
wire from the ceiling to the black
wire from the receiver.
white
•
Connect the blue wire from the
receiver to the blue wire (or
possibly black with white stripe
wire) from the fan.
•
Connect the white (grounded)
wire from the ceiling to both the
white wire from the receiver and
the white wire from the fan.
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Wall Control
Screw
Cut-Out
Drywall
Drill Holes
Before
Drywall
Anchors
Painter’s
Tape
Cover Plate
Template
Template
Template
After
1. Tape the provided wall control
template with painter’s tape at
the desired installation area.
2. Drill holes inside the four
corners of the template.
Note: Make sure the wall
control template is level before
proceeding to the next step.
1. Using a 9/64 drill bit, drill a hole
in each screw cut-out on the wall
control template.
2. Using a hammer, tap a drywall
anchor found in the wall control
hardware bag into each hole
until the drywall anchor is flush
with the wall.
1. Using a drywall punch saw,
cut out the interior shape of
the template using one of
the four drilled corners as a
starting point.
2. Remove the template and the
cut-out section of drywall.
1. Insert the wall control into the
dry wall cut out.
2. Align the screw holes in the wall
control with the drywall anchors.
3. Install the cover plate using
a Phillips Head screwdriver
to secure the two cover plate
screws found in the wall control
hardware bag through the wall
control and into the drywall
anchors.
If you are using a outlet box for wall control installation, the wires coming from the wall
control must be grounded using the attached green wire. If not placed in an outlet box, cap
the green wire coming from the wall control with an included wire nut.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Install the two canopy screws
found in the
hardware bag.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Blades
Install each blade using the blade nuts,
found in the hardware bag, and the blade
assembly screws, found in the
hardware
bag. Secure the blade to a blade iron using the
included Allen wrench.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Switch Housing
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Screw two housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Insert the third screw, found in
hardware bag, into place and then
tighten all three screws.
the
Make sure the upper switch housing is securely attached to
the mounting plate. Failure to properly secure all 3 assembly
screws could result in the switch housing fixture falling.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Light Kit
Bulb
Connect the plugs from the upper and
lower switch housings. Make sure to line up
the colored markings on the connectors.
Raise the lower switch housing to the
bottom of the upper switch housing. Install
all three switch housing screws found in
Install a halogen bulb in each socket. When
necessary, replace with bulbs of the same
type and wattage.
the
hardware bag.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
When installing a halogen bulb, carefully cut off the
end of the plastic sleeve packaging and hold the bulb
by the plastic sleeve to screw it into the socket.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Light Kit (Continued)
Notch
Carefully place the globe into the globe
ring. Support both the globe and the
globe ring during installation.
Carefully raise the globe assembly and
align the hammers on the globe ring with
the notches on the fan. Press all three
hammers into their respective notches.
See next page for fan
operation instructions.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Operation
Battery
Battery
Holder
ON
Battery
Door
Before operating the wall control, press on the
battery door to eject it. Unscrew the battery
holder. Insert the battery, found in the control
hardware bag, with the positive (+) side facing
downward. Reinstall the battery holder and
reinsert the battery door into the wall control.
The remote transmitter is already paired
to the receiver and ready to use.
Note: If you would like to operate
multiple fans or multiple remotes,
or if your remote is not working,
please see the Troubleshooting
section at the end of this manual.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Operation (continued)
Reverse
Button
The Safe-Exit Program gives
you about thirty seconds of
light when you turn the lights
off to exit the room before the
(Low)
Fan
Speed
(a)
Fan
Speed
lights go out.To use Safe-Exit:
• Press the fan power button
off for at least three seconds to
initiate the Safe-Exit Mode.
(High)
• The lights will flash for visual
confirmation.
Lights
Down
Lights
Up
• The lights will stay on 50%
brightness for 20 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
(b)
Fan
Power
Reverse
Battery
Holder
Quickly press the up or down arrow to turn the lights off
and on. Hold the up or down arrow to raise or dim the light
level. The reverse button changes the direction that the
blades turn. The power button turns the fan off and on.
The reverse button on the wall
control changes the air flow
pattern. In warm weather, use
(a) downward air flow pattern.
In cold weather, use (b) upward
air flow pattern.
Dimming Mode: To enable dimming, you must first set
your remote to Dimming Mode. To toggle Dimming
Mode on or off, hold down the Fan Power button while
pressing the Light Down arrow twice.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Maintenance & Cleaning
Globe
OFF
Be sure to turn off
power to the fan
before performing
any maintenance or
relamping.
Changing the bulbs - carefully release the
hammers holding the the globe to the fan.
Remove the bulbs and replace them with bulbs
of the same type and wattage. Reinstall the globe.
Cleaning the fan - use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
Note: In compliance with US federal energy regulations, this ceiling
fan contains a device that restricts its light output. Exceeding the
wattage limit marked on the MAX wattage sticker affixed to the
light socket(s) may result in fire hazard or improper operation.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Troubleshooting
Fan doesn’t work
Remote does not work
Excessive wobbling
• Press a fan speed button (1-4).
• Make sure the battery is installed
correctly.
• Tighten all of the blade screws
until they are snug.
AUTHORIZED SERVICE
CENTERS
For the most updated list of
Casablanca Authorized Service
Centers, visit
• Check the circuit breaker to
ensure the power is turned on.
• Install a new battery.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Check the wall control battery.
• Make sure the blades spin freely.
• If the remote still does not
work, you may need to pair
your remote. To prevent faulty
operation, please disconnect
power (at the wall switch,
call toll free 1-888-227-2178.
• Use the provided balancing
kit and instructions to balance
the fan.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on pages 10-11.
breaker, or fan) from all other
ceiling fans within range while
pairing. To pair: cycle power
to the fan by turning power off
and back on at the wall switch
(or circuit breaker if necessary).
Within three minutes, press and
hold both the Fan Off button and
the 4 button for four seconds to
pair the remote. If applicable, the
fan will turn on and the lights
will flash and stay on to indicate
successful pairing.
Lights will not dim
• To enable dimming, you
must first set your remote to
Dimming Mode. To toggle
Dimming Mode on or off, hold
down the Fan Power button
while pressing the Light Down
arrow twice.
Lights dim when turned on or
do not turn on at all.
• Check the plug connection in
the switch housing.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the
light sockets (see page 20 for
instructions on changing the
bulbs).
• Ensure each bulb you are using
supports dimming.
Noisy Operation
• Tighten the blade screws until
they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
1.888.227.2178
Troubleshooting (continued)
Installing Multiple Fans with Independently Operating Remote Controls
Installing One Fan Operating on Multiple Remote Controls
To install multiple fans with independently operating remote controls, there is no need to
perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply
install each receiver into a fan and use the appropriate transmitter to operate each fan.
To have multiple remote controls operate one fan, you must pair each additional transmitter
to the receiver in the fan. The transmitter that shipped with your fan is already paired.
Note: To prevent faulty operation, please disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while pairing.
If your remote is not working, see the “Remote does not work” section on the previous page.
For each additional transmitter, cycle power to the fan by turning power off and back on at
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
Installing Multiple Fans Operating on a Single Remote Control
“Unpairing” Procedure for Faulty Operation of Remote Controls
X
To have multiple fans operated by a single remote control, you must pair the transmitter to each
additional receiver. The receiver that shipped with your fan is already paired to the transmitter.
If a transmitter is mistakenly operating a fan, you need to “unpair” the transmitter from that
fan’s receiver. The “unpairing” procedure is the same as the pairing procedure.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while pairing each fan.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while “unpairing” a fan.
For each additional fan, ensure that a compatible receiver is installed. Disconnect power from all
other fans while pairing. To pair: cycle power to the fan by turning power off and back on at
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
Disconnect power from all other fans while “unpairing.” Then, cycle power to the fan you
wish to “unpair” by turning power off and back on at the wall switch (or circuit breaker
if necessary). Within three minutes, press and hold both the Fan Off button and the 4
button for four seconds to “unpair” the remote. If applicable, the fan will turn off and the
lights will flash and turn off to indicate successful “unpairing.”
22
Download from Www.Somanuals.com. All Manuals Search And Download.
M8521-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company
|