Carrier
Transicold
Container
Refrigeration
Model 69NT20-531-300
Streamline Scroll
Operation
& Service
T-309 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SUMMARY
GENERAL SAFETY NOTICES
The following general safety notices supplement the specific warnings and cautions appearing elsewhere in this
manual. They are recommended precautions that must be understood and applied during operation and maintenance
of the equipment covered herein. The general safety notices are presented in thefollowing threesections labeled: First
Aid, Operating Precautions and Maintenance Precautions. A listing of the specific warnings and cautions appearing
elsewhere in the manual follows the general safety notices.
FIRST AID
An injury, no matterhowslight, should nevergo unattended. Always obtain first aid ormedical attentionimmediately.
OPERATING PRECAUTIONS
Always wear safety glasses.
Keep hands, clothing and tools clear of the evaporator and condenser fans.
No work should beperformed on theunit until all circuit breakers, start-stop switches areturned off, and powersupply
is disconnected.
Always work in pairs. Never work on the equipment alone.
In case of severe vibration or unusual noise, stop the unit and investigate.
MAINTENANCE PRECAUTIONS
Beware of unannounced starting of the evaporator and condenser fans. Do not open the condenser fan grille or
evaporator access panels before turning power off, disconnecting and securing the power plug.
Besurepoweris turned offbeforeworking on motors, controllers, solenoid valves and electrical control switches. Tag
circuit breaker and power supply to prevent accidental energizing of circuit.
Do not bypass any electrical safety devices, e.g. bridging an overload, or using any sort of jumper wires. Problems
with the system should be diagnosed, and any necessary repairs performed, by qualified service personnel.
When performing any arcwelding on theunit orcontainer, disconnect all wire harness connectors from the modules in
both control boxes. Do not remove wire harness from the modules unless you are grounded to the unit frame with a
static safe wrist strap.
In case of electrical fire, open circuit switch and extinguish with CO2 (never use water).
UNIT LABEL IDENTIFICATION
To help identify the label hazards on the unit and explain the level of awareness each one carries, an explanation is
given with the appropriate consequences:
DANGER -- means an immediate hazard which WILL result in severe personal injury or death.
WARNING -- means to warn against hazards or unsafe conditions which COULD result in severe personal injury or
death.
CAUTION -- means to warn against potential hazard or unsafe practice which could result in minor personal injury,
product or property damage.
SPECIFIC WARNING AND CAUTION STATEMENTS
The statements listed below are applicable to the refrigeration unit and appear elsewhere in this manual. These
recommended precautions must be understood and applied during operation and maintenance of the equipment
covered herein.
WARNING
Beware of unannounced starting of the evaporator and condenser fans. The unit may cycle the fans
and compressor unexpectedly as control requirements dictate.
WARNING
Do not attempt to remove power plug(s) before turning OFF start-stop switch (ST), unit circuit break-
er(s) and external power source.
WARNING
Make sure the power plugs are clean and dry before connecting to any power receptacle.
T-309
Safety-1
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Make sure that the unit circuit breaker(s) (CB-1 & CB-2) and the START-STOP switch (ST) are in the
“O” (OFF) position before connecting to any electrical power source.
WARNING
Never use air for leak testing. It has been determined that pressurized, mixtures of refrigerant and air
can undergo combustion when exposed to an ignition source.
WARNING
Make sure power to the unit is OFF and power plug disconnected before replacing the compressor.
WARNING
Before disassembly of the compressor make sure to relieve the internal pressure very carefully by
slightly loosening the couplings to break the seal.
WARNING
Oakite No. 32 is an acid. Be sure that the acid is slowly added to the water. DO NOT PUT WATER
INTO THE ACID -- this will cause spattering and excessive heat.
WARNING
Wear rubber gloves and wash the solution from the skin immediately if accidental contact occurs. Do
not allow the solution to splash onto concrete.
WARNING
Always turn OFF the unit circuit breakers (CB-1 & CB-2) and disconnect main power supply before
working on moving parts.
WARNING
Make sure power to the unit is OFF and power plug disconnected before removing capacitor(s).
WARNING
With power OFF discharge the capacitor before disconnecting the circuit wiring.
WARNING
Do not use a nitrogen cylinder without a pressure regulator. Do not use oxygen in or near a refrigera-
tion system as an explosion may occur.
WARNING
Do not open the condenser fan grille before turning power OFF and disconnecting power plug.
WARNING
The Unit Power Plug Must Be Disconnected To Remove Power From Circuit Breaker Cb1
CAUTION
Do not remove wire harnesses from controller modules unless you are grounded to the unit frame with
a static safe wrist strap.
CAUTION
Unplug all controller modulewireharness connectors beforeperforming arcweldingon anypart ofthe
container.
CAUTION
When condenser water flow is below 11 lpm (3 gpm) or when water-cooled operation is not in use, the
CFS switch MUST be set to position ”1” or the unit will not operate properly.
CAUTION
Pre-trip inspection should not be performed with critical temperature cargoes in the container.
T-309
Safety-2
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
When Pre-Trip key is pressed, economy, dehumidification and bulb mode will be deactivated. At the
completion of Pre-Trip activity, economy, dehumidification and bulb mode must be reactivated.
CAUTION
When a failure occurs during automatic testing the unit will suspend operation awaiting operator in-
tervention.
CAUTION
When Pre--Trip test Auto 2 runs to completion without being interrupted, the unit will terminate pre-
trip and display “Auto 2” “end.” The unit will suspend operation until the user depresses the ENTER
key!
CAUTION
To prevent trapping liquid refrigerant in the manifold gauge set be sure set is brought to suction pres-
sure before disconnecting.
CAUTION
The scroll compressor achieves low suction pressure very quickly. Do not use the compressor to evacu-
ate the system below zero psig. Never operate the compressor with the suction or discharge service
valves closed (frontseated). Internal damage will result from operating the compressor in a deep vacu-
um.
CAUTION
Use only Carrier Transicold approved Polyol Ester Oil (POE) -- Mobil ST32 compressor oil with
R-134a. Buy in quantities ofone quart or smaller. When using this hygroscopicoil, immediately reseal.
Do not leave container of oil open or contamination will occur.
CAUTION
Take necessary steps (place plywood over coil or use sling on motor) to prevent motor from falling into
condenser coil.
CAUTION
DO NOT disassemble piston from NEW suction modulating valve powerhead assembly. Doing so may
result in damage to piston.
CAUTION
The unit must be OFF whenever a programming card is inserted or removed from the controller pro-
gramming port.
CAUTION
Do not allow moisture to enter wire splice area as this may affect the sensor resistance.
T-309
Safety-3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PARAGRAPH NUMBER
Page
GENERAL SAFETY NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety-1
FIRST AID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety-1
OPERATING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety-1
MAINTENANCE PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety-1
UNIT LABEL IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety-1
SPECIFIC WARNING AND CAUTION STATEMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety-1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 CONFIGURATION IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 OPTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2 Dehumidification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3 Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.5 Pressure Readout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.6 Interrogator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.7 Remote Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.8 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.9 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.10 Back Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.11 460 Volt Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.12 Cable Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.13 Upper Air (Fresh Air Make Up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.14 Evaporator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.15 Evaporator Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.16 Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.17 Plate Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.18 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.19 Stepper Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.20 Condenser Grille . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.1 Refrigeration Unit -- Front Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.2 Fresh Air Makeup Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.3 Evaporator Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.4 Compressor Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.5 Air Cooled Condenser Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.6 Control Box Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.7 Communications Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 REFRIGERATION SYSTEM DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 ELECTRICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 SAFETY AND PROTECTIVE DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5 REFRIGERATION CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-2
2-1
2-1
2-1
2-1
2-2
2-3
2-4
2-5
2-5
2-6
2-7
2-8
2-9
i
T309
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS (cont)
2.5.1 Standard Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.2 Economized Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.3 Unloaded Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MICROPROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 TEMPERATURE CONTROL MICROPROCESSOR SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1 Key Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.2 Display Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.3 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 CONTROLLER SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1 Configuration Software (Configuration Variables) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2 Operational Software (Function codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 MODES OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1 Temperature Control -- Perishable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2 Defrost Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.3 Failure Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.4 Generator Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.5 Compressor High Temperature, Low Pressure Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.6 Perishable Mode -- Conventional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.7 Perishable Mode -- Economy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.8 Perishable Mode -- Dehumidification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.9 Perishable, Dehumidification -- Bulb Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.10 Temperature Control -- Frozen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.11 Frozen Mode -- Conventional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 CONTROLLER ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5. UNIT PRE-TRIP DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6 DataCORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.2 DataCORDER Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.3 Sensor Configuration (dCF02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-9
2-9
2-9
3-1
3-1
3-2
3-2
3-3
3-3
3-3
3-4
3-4
3-4
3-4
3-4
3-4
3-4
3-4
3-5
3-5
3-5
3-6
3-6
3-6
3-7
3-7
3-7
3-7
3-8
3.6.4 Logging Interval (dCF03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.6.5 Thermistor Format (dCF04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.6.6 Sampling Type (dCF05 & dCF06) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.6.7 Alarm Configuration (dCF07 -- dCF10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.6.8 DataCORDER Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.6.9 Pre-Trip Data Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.6.10 DataCORDER Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.6.11 USDA Cold Treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.6.12 USDA Cold Treatment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.6.13 DataCORDER Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.6.14 ISO Trip Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
ii
T309
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS (cont)
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 INSPECTION (Before Starting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 CONNECT POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1 Connection To 380/460 vac Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 ADJUST FRESH AIR MAKEUP VENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1 Upper Fresh Air Makeup Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-1
4-1
4-1
4-1
4.4 CONNECT REMOTE MONITORING
RECEPTACLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
4-2
4-2
4-2
4-2
4-2
4-2
4-2
4-2
4-3
4-3
4-4
4-5
4-5
4.5 STARTING AND STOPPING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.1 Starting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.2 Stopping the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6 START--UP INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6.1 Physical Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6.2 Check Controller Function Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6.3 Complete Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7 PRE-TRIP DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8 OBSERVE UNIT OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8.1 Probe Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9 SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.1 Sequence Of operation -- Compressor Phase Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.2 Sequence Of Operation -- Perishable Mode Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.3 Sequence Of Operation --
Perishable Mode Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6
4-6
4-6
5-1
5-1
5-1
5-2
5-2
5-2
5-2
5-3
5-3
5-4
5-4
5-4
5-4
5-4
5-5
5-5
5-5
4.9.4 Sequence Of operation -- Frozen Mode Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.5 Sequence Of Operation -- Defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 UNIT WILL NOT START OR STARTS THEN STOPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 UNIT OPERATES LONG OR CONTINUOUSLY IN COOLING . . . . . . . . . . . . . . . . . . . . . . . . .
5.3 UNIT RUNS BUT HAS INSUFFICIENT COOLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4 UNIT WILL NOT HEAT OR HAS INSUFFICIENT HEATING . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5 UNIT WILL NOT TERMINATE HEATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6 UNIT WILL NOT DEFROST PROPERLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7 ABNORMAL PRESSURES (COOLING) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8 ABNORMAL NOISE OR VIBRATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.9 CONTROLLER MALFUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.10 NO EVAPORATOR AIR FLOW OR RESTRICTED AIR FLOW . . . . . . . . . . . . . . . . . . . . . . . . .
5.11 THERMOSTATIC EXPANSION VALVE MALFUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.12 AUTOTRANSFORMER MALFUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.13 WATER-COOLED CONDENSER OR WATER PRESSURE SWITCH . . . . . . . . . . . . . . . . . . . .
5.14 COMPRESSOR OPERATING IN REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.15 ABNORMAL TEMPERATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.16 ABNORMAL CURRENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii
T309
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS (cont)
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 SECTION LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 SERVICE VALVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3. MANIFOLD GAUGE SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4 PUMPING THE UNIT DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5 REFRIGERANT LEAK CHECKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6 EVACUATION AND DEHYDRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.2 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.3 Procedure - Complete system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.4 Procedure - Partial System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.7 REFRIGERANT CHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.7.1 Checking the Refrigerant Charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.7.2 Adding Refrigerant to System (Full Charge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.7.3 Adding Refrigerant to System (Partial Charge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.8 COMPRESSOR -- Model RSH105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.8.1 Removal and Replacement of Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.9 COMPRESSOR OIL LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.10 HIGH PRESSURE SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.10.1 Replacing High Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.10.2 Checking High Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.11 CONDENSER COIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.12 CONDENSER FAN AND MOTOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.13 FILTER-DRIER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.14 EXPANSION VALVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.14.1 Checking Superheat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.14.2 Valve Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.15 EVAPORATOR COIL AND HEATER
6-1
6-1
6-1
6-1
6-2
6-3
6-3
6-3
6-3
6-3
6-4
6-5
6-5
6-5
6-5
6-5
6-5
6-7
6-7
6-7
6-8
6-8
6-8
6-8
6-9
6-9
6-9
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.15.1 Evaporator Coil Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.15.2 Evaporator Heater Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.16 ECONOMIZER, UNLOADER, LIQUID INJECTION AND OIL RETURN SOLENOID VALVE 6-11
6.17 EVAPORATOR FAN AND MOTOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.17.1 Replacing The Evaporator Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.18 EVAPORATOR FAN MOTOR CAPACITORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.18.1 When To Check For A Defective Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.18.2 Removing The Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.18.3 Checking The Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.19 VALVE OVERRIDE CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
6.20 SUCTION MODULATION VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
6.20.1 Precheck Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
6.20.2 Checking The Stepper valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
6.21 CONTROLLER AND EXPANSION MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
iv
T309
Download from Www.Somanuals.com. All Manuals Search And Download.
6.21.1 Handling Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
6.21.2 Controller Trouble-Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
6.21.3 Controller Programming Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
6.21.4 Removing and Installing a Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
6.22 TEMPERATURE SENSOR SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
6.22.1 Sensor Checkout Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
6.22.2 Sensor Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
6.22.3 Sensor Re--Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.23 MAINTENANCE OF PAINTED SURFACES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.24 COMPOSITE CONTROL BOX REPAIRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.24.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.24.2 Cracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
6.24.3 Chips And Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
6.24.4 Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
6.24.5 Door Hinge Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
6.25 COMMUNICATIONS INTERFACE MODULE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 6-22
ELECTRICAL WIRING SCHEMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1
7.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1
v
T309
Download from Www.Somanuals.com. All Manuals Search And Download.
LIST OF ILLUSTRATIONS
FIGURE NUMBER
Page
2-1
2-2
2-3
2-4
2-5
2-10
2-11
2-11
3-1
3-2
3-2
3-3
3-9
3-11
4-1
4-4
4-5
4-5
4-6
4-6
4-7
6-1
6-1
6-1
6-2
6-3
6-4
6-6
6-6
6-8
6-9
6-9
6-10
6-10
6-11
Figure 2-1 Refrigeration Unit -- Front Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-2 Evaporator Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-3 Compressor Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-4 Condenser Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-5 Control Box Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-6 Refrigeration Circuit Schematic -- Standard Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-7 Refrigeration Circuit Schematic -- Economized Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-8 Refrigeration Circuit Schematic -- Unloaded Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3- 1 Temperature Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3- 2 Key Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3- 3 Display Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3- 4 Control and Expansion Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3- 5 Standard Configuration Download Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3- 6 Data Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-1 Make Up Air Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-2 Controller Operation -- Perishable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-3 Controller Operation -- Frozen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-4 Perishable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-5 Perishable Mode Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-6 Frozen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-7 Defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-1 Service Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-2 Suction Service Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-3 Manifold Gauge Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-4 R-134a Manifold Gauge/Hose Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-5. Refrigeration System Service Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-6. Compressor Service Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-7 Compressor Upper Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-8 Compressor Lower Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-9 High Pressure Switch Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-10 Thermostatic Expansion Valve Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-11 Evaporator Expansion Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-12 Hermetic Thermostatic Expansion Valve Brazing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-13 Economizer Expansion Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-14. Unloader Solenoid Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-15. Oil Return Solenoid Valve (ORV), Economizer Solenoid Valve (ESV),
Liquid Injection Solenoid Valve (LIV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-11
6-12
6-13
6-15
6-16
6-17
6-18
Figure 6-16. Evaporator Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-17 Suction Modulation Valve (SMV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-18 Controller Section of the Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-19 Sensor Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-20 Typical Sensor and Cable Splice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-21 Supply Sensor Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi
T309
Download from Www.Somanuals.com. All Manuals Search And Download.
LIST OF ILLUSTRATIONS
FIGURE NUMBER
Page
6-18
6-19
6-21
6-22
7-1
Figure 6-22 Return Sensor Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-23 Door Hinge Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-24. Insert Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-25. Communications Interface Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7-1 LEGEND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7-2 SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7-3 WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2
7-3
LIST OF TABLES
TABLE NUMBER
Page
2-8
Table 2-1 Safety and Protective Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-1 Key Pad Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-2 DataCORDER Configuration Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-3 DataCORDER Standard Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
3-8
3-8
Table 3-4 Controller Configuration Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Table 3-5 Controller Function Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Table 3-6 Controller Alarm Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
Table 3-7 Controller Pre-Trip Test Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Table 3-8 DataCORDER Function Code Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Table 3-9 DataCORDER Pre-Trip Result Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Table 3-10 DataCORDER Alarm Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Table 6-1 Compressor Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-6
Table 6-2 Sensor Temperature/Resistance Chart (+/--.002%) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
Table 6-3 Crack, Chip & Hole Repair Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
Table 6-4 Insert Repair Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
Table 6-5 Drill Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
Table 6-6 Recommended Bolt Torque Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
Table 6-7 R-134a Temperature - Pressure Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
vii
T309
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1
INTRODUCTION
1.1 INTRODUCTION
1.3.1 Battery
The controller may be fitted with standard replaceable
batteries or a rechargeable battery pack.
The Carrier Transicold model 69NT20--531-300 units
are of lightweight aluminum frame construction,
designed to fit in the front of a container and serve as the
container front wall.
1.3.2 Dehumidification
The unit may be fitted with a humidity sensor. This
sensor allows setting of a humidity set point in the
controller. In the dehumidification mode the controller
will operate to reduce internal container moisture level.
They are one piece, self-contained, all electric units
which are fitted with cooling and heating systems to
provide precise temperature control.
1.3.3 Control Box
The units are supplied with a complete charge of
refrigerant R-134a and compressor lubricating oil and
are ready for operation upon installation. Forklift
pockets are provided for unit installation and removal.
The control box is constructed of composite material
and may be fitted with a lockable door.
1.3.4 Temperature Readout
The base unit operates on nominal 380/460 volt, 3
phase, 50/60 hertz power. An optional autotransformer
may be fitted to allow operation on nominal 190/230 , 3
phase, 50/60 hertz power. Power for the control system
is provided by a transformer which steps the supply
power down to 18 and 24 volts, single phase.
The unit may be fitted with suction and discharge
temperature sensors. The sensor readings may be
viewed on the controller display.
1.3.5 Pres s ure Readout
The unit may be fitted with factory installed suction and
discharge pressure gauges. The unit is fitted with
suction and discharge transducers. The readings may be
viewed on the controller display.
The controller is a Carrier Transicold Micro-Link 2i
microprocessor. The controller will operate
automatically to select cooling, holding or heating as
required to maintain the desired set point temperature
within very close limits.
1.3.6 Interrogator
Units that usetheDataCORDER functionarefittedwith
interrogator receptacles for connection of equipment to
download the recorded data. Two receptacles may be
fitted, one accessible from the front of the unit and the
other mounted inside the container (with the USDA
receptacles).
The controller is fitted with a keypad and display for
viewing or changing operating parameters. The display
is also equipped with lights to indicatevarious modes of
operation.
1.2 CONFIGURATION IDENTIFICATION
1.3.7 Remote Monitoring
Unit identification information is provided on a model
plate located to the left of the economizer. The plate
provides the unit model number and the unit parts
identification number (PID). The model number
identifies the overall unit configuration while the PID
provides information on specific optional equipment,
factory provision to allow for field installation of
optional equipment and differences in detailed parts.
The unit may be fitted with a remote monitoring
receptacle. This item allows connection of remote
indicators for COOL, DEFROST and IN RANGE.
1.3.8 Communications
The unit may be fitted with a communications interface
module. The communications interface module is a
slave module which allows communication with a
master central monitoring station. The module will
respond to communication and return information over
the main power line. Refer to the ship master system
technical manual for further information.
Configuration identification for the models covered
herein are provided in the Carrier Transicold Container
Unit Matrix manual, publication T--300. Printed copies
of the T--300 may be obtained from Carrier Transicold.
Also, aweekly updated copy may befoundat theCarrier
1.3.9 Compres s or
The unit is fitted with a scroll compressor.
1.3.10 Back Panels
1.3 OPTION DESCRIPTIONS
Various options may be factory or field fitted to the base
unit. Brief descriptions of the options are provided in
the following subparagraphs.
Back panel designs that may be fitted include panels of
aluminum and stainless steel. Panels may be fitted with
access doors and/or hinge mounting.
1-1
T-309
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3.11 460 Volt Cable
example, additional operating instructions are required
to describe start--up of a unit equipped with an
autotransformer. Where the labels are available with
additional languages, they are listed in the parts list.
Various power cable and plug designs are available for
the main 460 volt supply. The plug options tailor the
cables to each customers requirements.
1.3.17 Plate Set
1.3.12 Cable Res traint
Each unit is equipped with a tethered set of wiring
schematic and wiring diagram plates.
The plate sets are ordered using a seven digit base part
number and a two digit dash number. (See Unit Matrix
Manual, T-300)
Various designs are available for storage of the power
cables. These options are variations of the compressor
section front cover.
1.3.13 Upper Air (Fres h Air Make Up)
The unit may be fitted with an upper fresh air makeup
assembly. These assemblies are supplied in two
designs, the standard design and the micro design. The
openings may also be fitted with screens.
1.3.18 Controller
Replacement controllers may be ordered as a universal
un--configured controller (without configuration
software) or configured.
1.3.14 Evaporator
1.3.19 Stepper Drive
The unit is fitted with an evaporator coil and a hermetic
thermal expansion valve.
All the units covered by this manual have suction
modulating valves which act to control system capacity.
Units indicated as being fitted with “stepper drive”have
digital control motors fitted to the suction modulating
valve to open and close the valve in steps as required.
1.3.15 Evaporator Fan Operation
The units are fitted with Normal Evaporator Fan
Operation, opening of an evaporator fan internal
protector will shut down the unit.
1.3.20 Condens er Grille
1.3.16 Labels
Operating Instruction and Function Code listing labels
will differ depending on the options installed. For
Two styles of condenser grilles are available, direct
bolted grilles and hinged grilles.
T-309
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2
DESCRIPTION
2.1 GENERAL DESCRIPTION
valve, suction modulation valve and evaporator coil
heaters. Theunit model number, serial number and parts
identification number can be found on the serial plate to
the left of the economizer.
2.1.1 Refrigeration Unit -- Front Section
The unit is designed so that the majority of the
components are accessible from the front, see
Figure 2-1. The upper access panels allow entry into the
evaporator section, and the center access panel allows
access to the evaporator expansion valve, unloader
2.1.2 Fres h Air Makeup Vent
The function of the upper or lower makeup air vent is to
provide ventilation for commodities that require fresh
air circulation.
1
15
14
2
3
13
12
4
11
10
9
8
7
6
16
5
1. Access Panel (Evap. Fan #1)
2. Access Panel (Heaters, Suction Modulating
Valve, Unloader Valve & Evaporator
Expansion Valve)
Parts Identification Number (PID) Plate
9. Power Cables and Plug
10. Condenser Fan
11. Interrogator Connector (Front left)
12. Blank Cover (Temperature Recorder Location)
13. Blank Cover (Lower Fresh Air Makeup Vent
Location)
14. Upper Fresh Air Makeup Vent
15. Access Panel (Evap. Fan #2)
16. Compressor Protection Panel (cutaway view)
3. Fork Lift Pockets
4. Control Box
5. Compressor
6. Receiver or Water Cooled Condenser
7. Economizer
8. Unit Serial Number, Model Number and
Figure 2-1 Refrigeration Unit -- Front Section
T-309
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.3 Evaporator Section
The evaporator fans circulate air through the container
by pulling it in the top of the unit, directing it through
the evaporator coil, where it is heated or cooled, and
discharging it at the bottom.
The evaporator section (Figure 2-2) contains the return
recorder sensor, return temperature sensor, evaporator
expansion valve, unloader valve, suction modulation
valve, dual-speed evaporator fans (EM1 and EM2),
evaporator coil and heater, defrost heaters, defrost
temperature sensor, heat termination thermostat and
suction temperature sensor.
The evaporator components are accessible by removing
the upper rear panel (as shown in the illustration) or by
removing the front access panels.
3
5
7
4
2
1
8
6
12
11
17
10
9
15
14
16
13
1. Evaporator Fan Motor #1
2. Return Recorder/Temperature Sensor
3. Humidity Sensor
4. Evaporator Fan Motor #2
5. Defrost Temperature Sensor
6. Heater Termination Thermostat
7. Evaporator Coil
8. Evaporator Coil Heaters
9. Evaporator Expansion Valve Bulb
10. Evaporator Expansion Valve
11. Low Side Access Valve
12. Suction Modulating Valve
13. Suction Temperature Sensor
14. To Compressor
15. From Coil
16. To Coil
17. Unloader Solenoid Valve
Figure 2-2 Evaporator Section
T-309
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.4 Compres s or Section
transducer, discharge temperature sensor and the
suction pressure transducers.
The compressor section includes the compressor (with
high pressure switch) and the oil separator.
The supply temperature sensor, supply recorder sensor
and ambient sensor are located at the left side of the
compressor.
This section also contains the oil return solenoid,
compressor power plug, the discharge pressure
2
1
4
23
22
9
10
21
Dis charge
Connection
(Hidden)
20
11
19
18
17
Economizer
Connection
Suction
12
13
8
7
6
Connection
11
14
11
Oil Return
Connection
16
5
15
3
1. Compressor Guard
12. Economizer Service Valve
13. Suction Service Valve
2. Supply Temperature/Supply Recorder Sensor
Assembly
14. Discharge Temperature Sensor
15. Oil Return Service Valve
16. Discharge Pressure Transducer
17. Oil Return Solenoid Valve
18. Oil Separator
3. Ambient Sensor
4. Supply Air Thermometer Port (location)
5. Oil Drain
6. Compressor
7. Compressor Sight Glass
19. From Economizer
20. To Condenser
8
Compressor Power Plug
Discharge Service Valve
9.
21. From Suction Modulating Valve
22. Suction Strainer
10. High Pressure Switch
11. Access Valve
23. Suction Pressure Transducer
Figure 2-3 Compres s or Section
T-309
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.5 Air Cooled Condens er Section
The condenser fan pulls air in the bottom of the coil and
it is discharged horizontally out through the condenser
fan grille.
This section also contains the economizer, economizer
solenoid valve, economizer expansion valve and the
liquid injection solenoid valve.
The air cooled condenser section (Figure 2-4) consists
of the condenser fan, condenser coil, receiver, sight
glass/moisture indicator, liquid line service valve,
filter-drier and fusible plug.
5
6
7
4
3
2
1
12
11
14
8
10
9
13
15
27
26
16
22
17
21
25
20
18
24
19
23
1. Grille and Venturi Assembly
2. Condenser Fan
3. Key
15. From Compressor Discharge
16. Discharge Pressure Transducer
17. Oil Separator
4. Condenser Fan Motor
5. Condenser Coil
18. To Oil Return Solenoid
19. Receiver
6. Condenser Motor Mounting Bracket
7. Condenser Coil Cover
8. Economizer
9. To Evaporator Expansion Valve
10. Liquid Injection Solenoid Valve
11. From Condenser
12. To Condenser
13. To Compressor Economizer Connection
14. To Unloader Solenoid Valve
20. Sight Glass/Moisture Indicator
21. Sight Glass
22. Fusible Plug
23. Access Valve
24. Liquid Line Service Valve
25. Filter-Drier
26. Economizer Expansion Valve
27. Economizer Solenoid Valve
Figure 2-4 Condens er Section
T-309
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.6 Control Box Section
2.1.7 Communications Interface Module
The control box (Figure 2-5) includes the manual
operation switches; circuit breaker (CB-1); compressor,
fan and heater contactors; control power transformer;
fuses; key pad; display module; current sensor module;
controller module expansion module and the
communications interface module.
The communications interface module is a slave
module which allow communication with a master
central monitoring station. The module will respond to
communication and return information over the main
power line. Refer to the master system technical manual
for further information.
1
2
3
4
5
6
7
8
20
19
18 17
16
15
14
13
12 11 10 9
1. Compressor Phase A Contactor
2. Compressor Phase B Contactor
3. Heater Contactor
11. Manual Defrost Switch
12. Condenser Fan Switch
13. Controller Battery Pack
4. Display Module
14. Interrogator Connector (Box Location)
15. Control Transformer
5. Communications Interface Module
6. Controller/DataCORDER Module (Controller)
7. Expansion Module
16. Evaporator Fan Contactor - High
17. Evaporator Fan Contactor - Low
18. Condenser Fan Contactor
19. Circuit Breaker -- 460V
8. Key Pad
9. Start-Stop Switch
10. Remote Monitoring Receptacle
20. Current Sensor Module
Figure 2-5 Control Box Section
T-309
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 REFRIGERATION SYSTEM DATA
Model
RSH105
46.5 kg (103 lb)
Mobil ST32
Weight (Dry)
Approved Oil
Oil Charge
a. Compres s or/Motor
As s embly
2957 ml (100 ounces)
The oil level range, with the compressor off,
should be between the bottom and one-eighth
level of the sight glass.
Oil Sight Glass
Verify at --18 _C
(0 _F) container box
temperature
b. Evaporator Expans ion
Valve Superheat
4.4 to 6.7 _C (8 to 12 _F)
c. Economizer Expans ion
Valve Superheat
4.4 to 11.1 _C (8 to 20 _F)
Opens
54 (¦ 3) _C = 130 (¦ 5) _F
38 (¦ 4) _C = 100 (¦ 7) _F
25 (¦ 1.0) kg/cm@ = 350 (¦ 10) psig
18 (¦ 0.7) kg/cm@ = 250 (¦ 10) psig
Charge Requirements -- R-134a
4--Row Coil
d. Heater Termination Thermos tat
e. High Pres s ure Switch
Closes
Cutout
Cut-In
Unit Configuration
Water-Cooled
Condenser
5.33 kg
(11.75 lbs)
f. Refrigerant Charge
4.99kg
(11.0 lbs)
Receiver
Melting point
Torque
99 _C = (210 _F)
6.2 to 6.9 mkg (45 to 50 ft-lbs)
8.9 to 9.7 mkg (65 to 70 ft-lbs)
35 ¦ 5% kg/cm@ = (500 ¦ 5% psig)
6.2 to 6.9 mkg (45 to 50 ft-lbs)
Refer to unit model number plate.
0.5 ¦ 0.2 kg/cm@ (7 ¦ 3 psig)
1.6 ¦ 0.4 kg/cm@ (22 ¦ 5 psig)
g. Fus ible Plug
h. Sight Glas s /Mois ture Indicator
i. Rupture Dis c
Torque
Bursts at
Torque
j. Unit Weight
Cut-In
Cutout
k. Water Pres s ure Switch
T-309
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 ELECTRICAL DATA
a. Circuit Breaker
CB-1 Trips at
29 amps
62.5 amps
87.5 amps
CB-2 (50 amp) Trips at
CB-2 (70 amp) Trips at
b. Compressor
Motor
Full Load Amps (FLA)
13 amps @ 460 vac
380 vac, Single Phase,
460 vac, Single Phase,
60 hz
50 hz
Full Load Amps
Horsepower
1.3 amps
1.6 amps
0.75 hp
c. Condenser Fan
Motor
0.43 hp
Rotations Per Minute
Voltage and Frequency
Bearing Lubrication
Rotation
1425 rpm
1725 rpm
360 -- 460 vac ¦ 2.5 hz
400 -- 500 vac ¦ 2.5 hz
Factory lubricated, additional grease not required.
Counter-clockwise when viewed from shaft end.
4
Number of Heaters
Rating
750 watts +5/--10% each @ 230 vac
66.8 to 77.2 ohms @ 20 _C (68 _F)
Sheath
d. Evaporator Coil
Heaters
Resistance (cold)
Type
380 vac/50 hz
460 vac/60 hz
Full Load Amps
High Speed
1.6
2.0
Full Load Amps
Low Speed
0.8
0.70
1.0
0.84
Nominal Horsepower
High Speed
Nominal Horsepower
Low Speed
0.09
0.11
e. Evaporator Fan
Motor(s )
Rotations Per Minute
High Speed
2850 rpm
3450 rpm
Rotations Per Minute
Low Speed
1425 rpm
1750 rpm
Voltage and Frequency
360 -- 460 vac ± 1.25 hz
180 -- 230 vac ± 1.25hz
400 -- 500 vac ± 1.5 hz
200 -- 250 vac ± 1.5 hz
Voltage & Frequency us-
ing power autotransformer
Bearing Lubrication
Rotation
Factory lubricated, additional grease not required
CW when viewed from shaft end
10 amps (F3)
Control Circuit
Controller/DataCORDER
Expansion Module
5 amps (F1 & F2)
f. Fus es
10 amps (F4)
T-309
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
PARAGRAPH 2.3 -- Continued
Orange wire
Power
Output
Red wire
Brown wire
Input voltage
Output voltage
Ground
5 vdc
0 to 3.3 vdc
g. Humidity Sens or
Output voltage readings vers es relative humidity (RH) percentage:
30%
50%
70%
90%
0.99 V
1.65 V
2.31 V
2.97 V
2.4 SAFETY AND PROTECTIVE DEVICES
IP-CP or HPS will shut down the compressor.
Open safety switch contacts on device IP-CM will shut
down the condenser fan motor.
Unit components are protected from damage by safety
and protective devices listed in the following table.
Thesedevices monitortheunit operating conditions and
open a set of electrical contacts when an unsafe
condition occurs.
The entire refrigeration unit will shut down if one of the
following safety devices open: (a) Circuit Breaker(s);
(b)Fuse(F3/15A); or(c) EvaporatorFan MotorInternal
Protector(s) -- (IP-EM).
Open safety switch contacts on either or both of devices
Table 2-1 Safety and Protective Devices
UNSAFE CONDITION
DEVICE
DEVICE SETTING
Circuit Breaker (CB-1) -- Manual Reset
Trips at 29 amps (460 vac)
Trips at 62.5 amps (230 vac)
Trips at 87.5 amps (230 vac)
Excessive current draw
Circuit Breaker (CB-2, 50 amp) --Manual Reset
Circuit Breaker (CB-2, 70 amp) --Manual Reset
Excessive current draw in the
control circuit
Fuse (F3)
10 amp rating
5 amp rating
10 amp rating
N/A
Excessive current draw by the
controller
Fuse (F1 & F2)
Excessive current draw by the
expansion module
Fuse (F4)
Excessive condenser fan mo-
tor winding temperature
Internal Protector (IP-CM) -- Automatic Reset
Internal Protector (IP-CP) -- Automatic Reset
Excessive compressor motor
winding temperature
N/A
Excessive evaporator fan mo-
tor(s) winding temperature
Internal Protector(s) (IP-EM) -- Automatic Reset
Fusible Plug -- Used on the Receiver
N/A
93 _C = (200 _F)
Abnormal pressures/tempera-
tures in the high refrigerant
side
Rupture Disc -- Used on the Water-Cooled Con- 35 kg/cm@ = (500 psig)
denser
Abnormally high discharge
pressure
Opens at 25 kg/cm@
High Pressure Switch (HPS)
(350 psig)
T-309
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 REFRIGERATION CIRCUIT
2.5.1 Standard Operation
2.5.2 Economized Operation
In the economized mode the frozen rangeand pull down
capacity of theunit is increased by subcooling theliquid
refrigerant entering the evaporator expansion valve.
Overall efficiency is increased because the gas leaving
the economizer enters the compressor at a higher
pressure, therefore requiring less energy to compress it
to the required condensing conditions.
Starting at the compressor, (see Figure 2-6, upper
schematic) the suction gas is compressed to a higher
pressure and temperature.
In thestandard mode, both theeconomizer and unloader
solenoid valves are closed. The gas flows through the
discharge service valve into the oil separator. In the
separator, oil is removed from the refrigerant and stored
forreturn to the compressorwhen theoil return solenoid
valveis opened by thecontroller. Theoil return solenoid
valveis anormally open valvewhich allowsreturn ofoil
during the off cycle.
The refrigerant gas continues into the air-cooled
condenser. When operating with the air-cooled
condenser active, air flowing across the coil fins and
tubes cools the gas to saturation temperature. By
removing latent heat, the gas condenses to a high
pressure/high temperature liquid and flows to the
receiver which stores the additional charge necessary
for low temperature operation.
During economized operation, flow of refrigerant
through the main refrigerant system is identical to the
standard mode. (The unloader solenoid valve is
de--energized [closed] by the controller.)
Liquid refrigerant for use in the economizer circuit is
taken from the main liquid line as it leaves the
filter--drier (see Figure 2-7). The flow is activated when
the controller energizes the economizer solenoid valve.
The liquid refrigerant flows through the economizer
expansion valve and the economizer internal passages
absorbing heat from the liquid refrigerant flowing to the
evaporator expansion valve. The resultant “medium”
temperature/pressure gas enters the compressor at the
economizer service valve.
When operating with the water cooled condenser active
(see Figure 2-6, lower schematic), the refrigerant gas
passes through the air cooled condenser and enters the
water cooled condenser shell. The water flowing inside
the tubing cools the gas to saturation temperature in the
same manner as the air passing over the air cooled
condenser. The refrigerant condenses on the outside of
the tubes and exits as a high temperature liquid. The
water cooled condenser also acts as a receiver, storing
excess refrigerant.
2.5.3 Unloaded Operation
The system will operate in the unloaded mode during
periods of low load, during periods of required
discharge pressure or current limiting, and during
start--up.
The liquid refrigerant continues through the liquid line
service valve, the filter-drier (which keeps refrigerant
clean and dry) and the economizer (which is not active
during standard operation) to the evaporator expansion
valve. As the liquid refrigerant passes through the
variable orifice of the expansion valve, some of it
vaporizes into a gas (flash gas). Heat is absorbed from
the return air by the balance of the liquid, causing it to
vaporize in the evaporator coil. The vapor then flows
through the suction modulation valve to the
compressor.
During unloaded operation, flow of refrigerant through
the main refrigerant system is identical to the standard
mode. (The economizer solenoid valve is de--energized
[closed] by the controller.)
In the unloaded mode, a portion of the mid--stage
compressed gas is bypassed to decrease compressor
capacity. The flow is activated when the controller
opens the unloader solenoid valve (see Figure 2-7.
Opening of the valve creates a bypass from the
economizerservicevalve through the unloadersolenoid
valve and into the suction line on the outlet side of the
suction pressure modulation valve.
The evaporator expansion valve is activated by the bulb
strapped to the suction line near the evaporator outlet.
The valve maintains a constant superheat at the coil
outlet regardless of load conditions.
On systems fitted with a water pressure switch, the
condenser fan will be off when there is sufficient
pressure to open the switch. If water pressure drops
below the switch cut out setting, the condenser fan will
be automatically started. When operating a system
fitted with a condenser fan switch, the condenser fan
will be off when the switch is placed in the “O” position.
The condenser fan will be on when the switch is placed
in the “I” position.
As load on thesystem decreases, thesuctionmodulating
valve decreases flow of refrigerant to the compressor.
This action balances the compressor capacity with the
load and prevents operation with low coil temperatures.
In this mode of operation, the liquid injection solenoid
valve will open as required to provide sufficient liquid
refrigerant flow into the suction line for cooling of the
compressor motor.
T-309
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD OPERATION WITH RECEIVER
EVAPORATOR
LOW SIDE ACCESS VALVE
TXV BULB
TXV
SMV
CONDENSER
USV
LIV
STS
ECONOMIZER TXV BULB
ECONOMIZER
FILTER
DRIER
DISCHARGE
SERVICE
CONNECTION
DPT
CPDS
ESV
HPS
OIL SEPARATOR
ECONOMIZER
SERVICE
CONNECTION
RECEIVER
ECONOMIZER
TXV
ORV
FUSIBLE PLUG
SUCTION SERVICE
CONNECTION
SIGHT GLASS
MOISTURE INDICATOR
OIL RETURN
SERVICE VALVE
SPT
LIQUID LINE
SERVICE
CONNECTION
COMPRESSOR
DISCHARGE
LIQUID
SUCTION
STANDARD OPERATION WITH WATER COOLED CONDENSER
EVAPORATOR
LOW SIDE ACCESS VALVE
TXV BULB
TXV
SMV
CONDENSER
USV
LIV
CPSS
QUENCH
TXV
BULB
ECONOMIZER TXV BULB
ECONOMIZER
FILTER
DRIER
DISCHARGE
SERVICE
CONNECTION
DPT
CPDS
RUPTURE DISC
ESV
HPS
ECONOMIZER
SERVICE
CONNECTION
ECONOMIZER
TXV
ORV
SIGHTGLASS/
MOISTURE INDICATOR
SUCTION SERVICE
CONNECTION
OIL RETURN
SERVICE VALVE
SPT
WATER COOLED
CONDENSER
LIQUID LINE
SERVICE
CONNECTION
COMPRESSOR
Figure 2-6 Refrigeration Circuit Schematic -- Standard Operation
T-309
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
EVAPORATOR
LOW SIDE ACCESS VALVE
TXV BULB
TXV
SMV
CONDENSER
LIV
ECONOMIZER TXV BULB
ECONOMIZER
ESV
OIL SEPARATOR
ECONOMIZER
SERVICE
ECONOMIZER
TXV
CONNECTION
RECEIVER
LIQUID LINE
SERVICE CONNECTION
LIQUID
ECONOMIZER PRESSURE
Figure 2-7 Refrigeration Circuit Schematic -- Economized Operation
SMV
TXV BULB
TXV
USV
LIV
ECONOMIZER TXV BULB
OIL SEPARATOR
SUCTION SERVICE
CONNECTION
RECEIVER
LIQUID
ECONOMIZER PRESSURE
SUCTION
Figure 2-8 Refrigeration Circuit Schematic -- Unloaded Operation
T-309
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3
MICROPROCESSOR
3.1 TEMPERATURE CONTROL MICROPRO-
record unit operating parameters and cargo temperature
parameters for future retrieval. Coverage of the
temperaturecontrol softwarebegins with paragraph3.2.
Coverage of the DataCORDER software is provided in
paragraph 3.6.
CESSOR SYSTEM
The temperature control Micro-Link 2i microprocessor
system (see Figure 3- 1) consists of a key pad, display
module, the control module & expansion module set
(controller) and interconnecting wiring. The controller
houses the temperature control software and the
DataCORDER Software. The temperature control
software functions to operate the unit components as
required to provide the desired cargo temperature and
humidity. The DataCORDER software functions to
The key pad and display module serve to provide user
access and readouts for both of the controller functions,
temperature control and DataCORDER. The functions
are accessed by key pad selections and viewed on the
display module. Thecomponents aredesigned to permit
ease of installation and removal.
CONTROL MODULE
EXPANSION MODULE
DISPLAY MODULE
C
O
N
T
R
O
L
L
E
R
KEY PAD
TEMPERATURE CONTROL SOFTWARE
CONFIGURATION OPERATIONAL
ALARMS
(AL<70)
PRE--TRIP
INTERROGATION
CONNECTOR
SOFTWARE
SOFTWARE
CONFIGURATION
VARIABLE
FUNCTION
CODE (Cd)
TO
DISPLAY
(CnF##)
DATAREADER
DataCORDER SOFTWARE
CONFIGURATION OPERATIONAL
ALARMS
(AL>69)
DATA
STORAGE
MEMORY
SOFTWARE
SOFTWARE
Computer Device
With DataLine
Software
CONFIGURATION
VARIABLE
(dCF## read only)
FUNCTION
CODE (dC)
TO
DISPLAY
TO
DISPLAY
(Scrollback)
Figure 3- 1 Temperature Control Sys tem
T-309
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.1 Key Pad
Table 3-1 Key Pad Function
FUNCTION
KEY
The key pad (Figure 3- 2) is mounted on the right-hand
side of the control box. The key pad consists of eleven
push button switches that act as the user’s interface with
the controller. Descriptions of the switch functions are
provided in Table 3-1.
Code Select Accesses function codes.
Displays the pre-trip selection menu. Dis-
continues pre-trip in progress.
Pre-Trip
Displays alarm list and clears the alarm
queue.
Alarm List
Defrost
Interval
Displays selected defrost interval.
PRE
TRIP
CODE
SELECT
Confirms a selection or saves a selection
to the controller.
Enter
DEFROST
INTERVAL
ALARM
LIST
Change or scroll a selection upward Pre-
trip advance or test interruption.
Arrow Up
Arrow
Down
Change or scroll a selection downward.
Pre-trip repeat backward.
Return/
Supply
Displays non-controlling probe tempera-
ture (momentary display).
ENTER
Displays alternate English/Metric scale
(momentary display). When set to _F,
pressure is displayed in psig and vacuum
in “/hg. “P” appears after the value to in-
dicate psig and “i” appears for inches of
mercury.
_C/_F
RETURN
SUPPLY
_C
_F
When set to _C. pressure readings are in
bars. “b” appears after the value to indi-
cate bars.
ALT.
MODE
BATTERY
POWER
Initiate battery backup mode to allow set
point and function code selection if AC
power is not connected.
Battery
Power
This key is pressed to switch the functions
from the temperature software to the Da-
taCORDER Software. The remaining keys
function the same as described above ex-
cept the readings or changes are made to
the DataCORDER programming..
Figure 3- 2 Key Pad
ALT Mode
COOL
HEAT DEFROST IN RANGE ALARM SUPPLY RETURN
NOTE
SETPOINT/Code
AIR TEMPERATURE/Data
The controlling probe in the perishable range
will be the SUPPLY air probe and the control-
ling probe in the frozen range will be the
RETURN air probe.
Figure 3- 3 Dis play Module
5. Supply -- Yellow LED: Energized when the supply air
probe is used for control. When this LED is illumi-
nated, the temperature displayed in the AIR TEMPER-
ATURE display is the reading at the supply air probe.
This LED will flash if dehumidification or humidifi-
cation is enabled.
3.1.2 Dis play Module
The display module (Figure 3- 3) consists of two
backlighted five digit LCD displays and seven indicator
lights. The indicator lights include:
1. Cool -- White LED: Energized when the refrigerant
compressor is energized.
6. Return -- Yellow LED: Energized when the return air
probe is used for control. When this LED is illumi-
nated, the temperature displayed in the AIR TEM-
PERATURE display is the reading at the return air pro-
be. This LED will flash if dehumidification or
humidification is enabled.
2. Heat -- Orange LED: Energized to indicate heater op-
eration in the heat or defrost mode.
3. Defrost -- OrangeLED: Energized when theunit is in
the defrost mode.
4. In-Range -- Green LED: Energized when the con-
trolled temperature probe is within specified toler-
ance of set point.
7. Alarm -- Red LED: Energized when there is an active
or an inactive shutdown alarm in the alarm queue
T-309
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
3
3
4
5
3
6
7
3
8
3
1
2
3
3
3
3
3
9
1
1. Mounting Screw
6. Control Circuit Power Connection
(Location: In back of controller)
7. Software Programming Port
8. Battery Pack
2. Micro-Link 2i Control/DataCORDER Module
3. Connectors
4. Test Points
5. Fuses
9. Expansion Module
Figure 3- 4 Control and Expans ion Modules
3.1.3 Controller
c. Provide ability to read and (if applicable) modify the
Configuration Software Variables, Operating Soft-
ware Function Codes and Alarm Code Indications.
CAUTION
Do not remove wire harnesses from control-
ler modules unless you are grounded to the
unit frame with a static safe wrist strap.
d. ProvideaPre-Trip step-by-step checkout ofrefrigera-
tion unit performance including: proper component
operation, electronic and refrigeration control opera-
tion, heater operation, probe calibration, pressure
limiting and current limiting settings.
CAUTION
Unplug all controller module wire harness
connectors before performing arc welding
on any part of the container.
e. Provide battery powered ability to access or change
selected codes and set point without AC power con-
nected
NOTE
Do not attempt to service the controller mod-
ules. Breaking the seal will void the warranty.
f. Provide the ability to reprogram the software through
the use of a memory card. The memory card automat-
ically downloads newsoftware to the controllerwhen
inserted.
The Micro--Link 2i controller is a dual module
microprocessor as shown in Figure 3- 4. It is fitted with
test points, harness connectors and a software card
programming port.
3.2.1 Configuration Software (Configuration Vari-
ables )
3.2 CONTROLLER SOFTWARE
The controller software is a custom designed program
that is subdivided into the Configuration Software and
the Operational Software. The controller software
performs the following functions:
The Configuration Software is a variable listing of the
components available for use by the Operational
Software. This software is factory installed in
accordance with the equipment fitted and options listed
on the original purchase order. Changes to the
Configuration Software are required only when a new
controller hase been installed or a physical change has
been made to the unit such as the addition or removal of
an option. A Configuration Variable list is provided in
Table 3-4. Change to the factory installed
Configuration Software is achieved via a configuration
card or communications.
a. Control supply or return air temperature to required
limits, provide modulated refrigeration operation,
economized operation, unloaded operation, electric
heat control and defrost. Defrost is performed to clear
build up of frost and ice and ensure proper air flow
across the coil.
b. Provide default independent readouts of set point and
supply or return air temperatures.
T-309
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.2 Operational Software (Function codes )
3.3.2 Defros t Interval
Function code Cd27 may be operator set to initiate
defrost at intervals of 3, 6, 9, 12 or 24 hours. It may also
be set to OFF (no defrost). The factory default is 12
hours. (Refer to Table 3-5).
The Operational Software is the actual operation
programming of the controller which activates or
deactivates components in accordance with current unit
operating conditions and operator selected modes of
operation.
3.3.3 Failure Action
Function code Cd29 may be operator set to allow
continued operation in the event the control sensors are
reading out of range. The factory default is full system
shutdown. (Refer to Table 3-5).
The programming is divided into function Codes. Some
of the codes are read only while the remaining codes
may be user configured. The value of the user
configurable codes can be assigned in accordance with
user desired mode of operation. A list of the function
codes is provided in Table 3-5.
3.3.4 Generator Protection
Function codes Cd31(Stagger Start, Offset Time) and
Cd32 (Current Limit) may be operator set to control
start up sequenceofmultiple units and operating current
draw. The factory default allows on demand starting (no
delay) of units and normal current draw. Refer to
Table 3-5.
To access the function codes, perform the following:
a. Press the CODE SELECT key, then press an arrow
key until the left window displays the desired code
number.
3.3.5 Compres s or High Temperature, Low Pres -
s ure Protection.
The controller monitors compressor suction and
discharge temperatures and pressures. If the discharge
temperature exceeds a certain limit, the liquid injection
valve is opened to provide sufficient liquid refrigerant
flow into the economizer line to reduce the discharge
temperature. If the liquid injection is unable to reduce
the discharge temperature sufficiently and the
temperature exceeds the allowed limit, the compressor
will cycle off on a 3 minute timer. The compressor will
also cycle off in a similar manner if the suction pressure
falls belowtheallowed limit. Condenser and evaporator
fans continue to operate during the compressor off
cycle.
b. The right window will display the value of this item
for five seconds before returning to the normal dis-
play mode.
c. If a longer time is desired, press the ENTER key to
extend the time to 30 seconds.
3.3 MODES OF OPERATION
The Operational Software responds to various inputs.
These inputs come from the temperature and pressure
sensors, the temperature set point, the settings of the the
configuration variables and the function code
assignments. The action taken by the Operational
Software will change if any one of the inputs changes.
Overall interaction of the inputs is described as a
“mode” of operation. The modes of operation include,
perishable (chill) mode and frozen mode. Descriptions
of the controller interaction and modes of operation are
provided in the following sub paragraphs.
3.3.6 Peris hable Mode -- Conventional
The unit is capable of maintaining supply air
temperature to within ¦ 0.25_C (¦ 0.5_F) of set point.
Supply air temperature is controlled by positioning of
the suction modulation valve (SMV), cycling of the
compressor and cycling of the heaters.
When cooling from a temperature that is more than
2.5_C (4.5_F) above set point, the system will be in the
perishable pull down mode. It will be in economized
operation with a target SMV position of 100% open.
However, pressure and current limit functions may
restrict the valve, if either exceeds the preset value.
3.3.1 Temperature Control -- Peris hable Mode
Once set point is reached, the unit will transition to the
perishable steady state mode. This results in unloaded
operation with some restriction of the SMV. The SMV
will continue to close and restrict refrigerant flow until
the capacity of the unit and the load are balanced.
If the SMV is at minimum modulation, the controller
has determined that cooling is not required, or the
controllerlogicdetermines suction pressureis at thelow
pressure limit, the unit will transition to the perishable
idle mode. The compressor is turned off and the
evaporator fans continue to run to circulate air
throughout the container. If temperature rises above set
point +0.2_C, the unit will transition back to the
perishable steady state mode
With configuration variable CnF26 (Heat Lockout
Temperature) set to --10_C the perishable mode of
operation is active with set points at or above --10_C
(+14_F). With the variable set to --5_C, the perishable
mode is active at or above --5_C (+23_F). Refer to
Table 3-4.
When in the perishable mode the controller maintains
the supply air temperature at set point, the SUPPLY
indicatorlight will beilluminated onthedisplaymodule
and the default reading on the display window will be
the supply temperature sensor reading.
When the supply air temperature enters the in-range
temperature tolerance (as selected at function code
Cd30), the in-range light will energize.
If the temperature drops to 0.5_C (0.9_F) below set
point, the unit will transition to the perishable heating
T-309
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
mode and the heaters will be energized . The unit will
transition back to the perishable idle mode when the
temperature rises to 0.2_C (0.4_F) below the set point
and the heaters will de-energize
causes the controller to open the suction modulating
valve to match the increased heat load while still
holding the supply air temperature very close to the set
point.
Opening the modulating valve reduces the temperature
of the evaporator coil surface, which increases the rate at
which water is condensed from the passing air.
Removing water from the air reduces the relative
humidity. When the relative humidity sensed is 2%
below the set point , the controller de-energizes the heat
relay. The controller will continue to cycle heating to
maintain relative humidity below the selected set point.
If the mode is terminated by a condition other than the
humidity sensor, e.g., an out-of-range or compressor
shutdown condition, the heat relay is de-energized
immediately.
3.3.7 Peris hable Mode -- Economy
The economy mode is an extension of the conventional
mode. The mode is activated when the setting of
function code Cd34 is “ON”. Economy mode is
provided for power saving purposes. Economy mode
could be utilized in the transportation of temperature
tolerant cargo or non-respiration items which do not
require high airflow for removing respiration heat.
There is no active display indicator that economy mode
has been activated. To check for economy mode,
perform a manual display of code Cd34.
In order to achieve economy mode, a perishable set
point must be selected prior to activation. When
economy mode is active, the evaporator fans will be
controlled as follows:
Two timers are activated in the dehumidification mode
to prevent rapid cycling and consequent contactor wear.
They are:
1. Heater debounce timer (three minutes).
2. Out-of-range timer (five minutes).
The heater debounce timer is started whenever the
heater contactor status is changed. The heat contactor
remains energized (or de-energized) for at least three
minutes even if the set point criteria are satisfied.
The out-of-range timer is started to maintain heater
operation during a temporary out-of-range condition. If
the supply air temperature remains outside of the user
selected in-range setting for more than five minutes, the
heaters will be de-energized to allow the system to
recover. The out-of-range timer starts as soon as the
temperature exceeds the in-range tolerance value set by
function code Cd30.
At the start of each cooling or heating cycle, the
evaporator fans will be run in high speed for three
minutes. They will then be switched to low speed any
time the supply air temperature is within ¦ 0.25_C
(0.45_F)oftheset point and thereturn air temperatureis
less than or equal to the supply air temperature + 3_C
(5.4_F). The fans will continue to run in low speed for
one hour. At the end of the hour, theevaporator fans will
switch back to high speed and the cycle will be repeated.
If bulb mode is active, the economy fan activity will be
overwritten.
3.3.8 Peris hable Mode -- Dehumidification
The dehumidification mode is provided to reduce the
humidity levels inside the container. The mode is
activated when a humidity value is set at at function
code Cd33. The display module SUPPLY led will flash
ON and OFF every second to indicate that the
dehumidification mode is active. Once the Mode is
active and the following conditions are satisfied, the
controller will activate the heat relay to begin
dehumidification.
3.3.9 Peris hable, Dehumidification -- Bulb Mode
Bulb mode is an extension of the dehumidification
mode which allows changes to the evaporator fan speed
and/or defrost termination set points.
Bulb mode is active when configuration code Cd35 is
set to “Bulb”. Once the bulb mode is activated, the user
may then change thedehumidification modeevaporator
fan operation from the default (speed alternates from
low to high each hour) to constant low or constant high
speed. This is done by toggling function code Cd36
from its default of“alt”to “Lo”or“Hi”as desired. Iflow
speed evaporator fan operation is selected, this gives the
user the additional capability of selecting
dehumidification set points from 60 to 95% (instead of
the normal 65 to 95%).
1. The humidity sensor reading is above the set point.
2. The unit is in the perishable steady state mode and
supply air temperature is less than 0.25_C above set
point.
3. The heater debouncetimer (threeminutes) has timed
out.
4. Heater termination thermostat (HTT) is closed.
In addition, if bulb mode is active, function code Cd37
may be set to override the previous defrost termination
thermostat settings. (Refer to paragraph 4.9.5.) The
temperature at which the defrost termination thermostat
will be considered “open” may be changed [in 0.1_C
(0.2_F) increments] to any value between 25.6_C
(78_F)and 4_C (39.2_F) . The temperatureat which the
defrost termination thermostat is considered closed for
interval timer start or demand defrost is 10_C for
“open” values from 25.6_C (78_F) down to a 10_C
setting. For “open” values lower than 10_C, the
“closed” values will decrease to the same value as the
“open” setting. Bulb mode is terminated when:
If the above conditions are true the evaporator fans will
switch from high to low speed operation. The
evaporatorfan speed will switch everyhourthereafteras
long as all conditions are met (see Bulb Mode section
for different evaporator fan speed options). If any
condition except for item (1) becomes false OR if the
relative humidity sensed is 2% below the
dehumidification set point, the high speed evaporator
fans will be energized.
In the dehumidification mode power is applied to the
defrost and drain pan heaters. This added heat load
T-309
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Bulb mode code Cd35 is set to “Nor.”
to “ON”. When economy mode frozen is active, the
system will perform normal frozen mode operations
except that the entire refrigeration system, excluding
the controller, will be turned off when the control
temperature is less than or equal to the set point -- 2_C.
After an off-cycle period of 60 minutes, the unit will
turn on high speed evaporator fans for three minutes,
and then check the control temperature. If the control
temperature is greater than or equal to the set point +
0.2_C., the unit will restart the refrigeration system and
continue to cool until the previously mentioned
off-cycle temperature criteria are met. If the control
temperature is less than the set point + 0.2_C, the unit
will turn off the evaporator fans and restart another 60
minute off-cycle.
2. Dehumidification code Cd33 is set to “Off.”
3. The user changes the set point to one
that is in the frozen range.
When bulb mode is disabled by any of the above, the
evaporator fan operation for dehumidification reverts to
“alt” and the DTS termination setting resets to the value
determined by controllerconfiguration variableCnF41.
3.3.10 Temperature Control -- Frozen Mode
With configuration variable CnF26 (Heat Lockout
Temperature) set to --10_C the frozen mode ofoperation
is active with set points at or below --10_C (+14_F).
With the variable set to --5_C, the frozen mode is active
at or below --5_C (+23_F).
3.4 CONTROLLER ALARMS
When in the frozen mode the controller maintains the
return air temperature at set point, the RETURN
indicatorlight will beilluminated onthedisplaymodule
and the default reading on the display window will be
the return air probe reading.
Alarm display is an independent controller software
function. If an operating parameter is outside of
expected range or a components does not return the
correct signals back to the controller an alarm is
generated. A listing of the alarms is provided in
Table 3-6.
When the return air temperature enters the in-range
temperature tolerance as selected at function code
Cd30, the in-range light will energize.
The alarm philosophy balances the protection of the
refrigeration unit and that of the refrigerated cargo. The
action taken when an error is detected always considers
the survival of the cargo. Rechecks are made to confirm
that an error actually exists.
3.3.11 Frozen Mode -- Conventional
Frozen range cargos are not sensitive to minor
temperature changes. The method of temperature
control employed in this range takes advantage of this
fact to greatly improve the energy efficiency of the unit.
Temperature control in the frozen range isaccomplished
by cycling thecompressoron and offas theload demand
requires.
Some alarms requiring compressor shutdown havetime
delays before and after to try to keep the compressor on
line. An example is alarm code “LO”, (low main
voltage), when a voltage drop of over 25% occurs, an
indication is given on the display, but the unit will
continue to run.
When cooling from a temperature that is more than
2.5_C (4.5_F) above set point, the system will be in the
frozen pull down mode. It will transition to economized
operation with a target SMV position of 100% open.
However, pressure and current limit functions may
restrict the valve, if either exceeds the preset value.
When an Alarm Occurs:
a. The red alarm light will illuminate for alarm code
numbers 13, 17, 20, 21, 22, 23, 24, 25, 26, and 27.
b. If a detectable problem is found to exist, its alarm
code will be alternately displayed with the set point
on the left display.
Once set point is reached, the unit will transition to the
frozen steady state mode. (Economized operation with
maximum allowed suction modulating valve opening.)
c. The user should scroll through the alarm list to deter-
mine what alarms exist or have existed. Alarms must
be diagnosed and corrected before the Alarm List can
be cleared.
When temperature drops to set point minus 0.2_C and
the compressor has run for at least five minutes, the unit
will transition to the frozen idle mode. The compressor
is turned off and the evaporator fans continue to run to
circulate air throughout the container. If temperature
rises above set point +0.2_C, the unit will transition
back to the frozen steady state mode.
To Display Alarm Codes :
a. While in the Default Display mode, press the
ALARM LIST key. This accesses the Alarm List Dis-
play Mode, which displays any alarms archived in the
Alarm Queue.
If the temperature drops 10_C below set point, the unit
will transition to the frozen “heating” mode. In the
frozen heating mode the evaporator fans are brought to
high speed. The unit will transition back to the frozen
steady statemodewhen thetemperaturerises back tothe
transition point.
b. The alarm queue stores up to 16 alarms in the se-
quence in which they occurred. The user may scroll
through the list by depressing an ARROW key.
c. The left display will show “AL##,” where ## is the
alarm number sequentially in the queue.
3.3.12 Frozen Mode -- Economy
d. The right display will show the actual alarm code.
“AA##” will display for an active alarm, where “##”
is the alarm code. Or “IA##” will display for an inac-
tive alarm. See Table 3-6.
In order to activate economy frozen mode operation, a
frozen set point temperature must be selected. The
economy mode is active when function codeCd34 is set
T-309
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
e. “END” is displayed to indicate the end of the alarm
list if any alarms are active.
The DataCORDER performs the following functions:
a. Logs data at 15, 30, 60 or 120 minute intervals and
stores two years’ of data (based on one hour interval).
f. “CLEAr” is displayed if all alarms are inactive. The
alarm queue may than be cleared by pressing the EN-
TER key. The alarm list will clear and “-- -- -- -- -- ”
will be displayed.
b. Records and displays alarms on the display module.
c. Records results of pre--trip testing.
d. Records DataCORDER and temperature controlsoft-
ware generated data and events as follows:
3.5. UNIT PRE-TRIP DIAGNOSTICS
Pre--Trip Diagnostics is an independent controller
function which will suspend normal refrigeration
controller activities and provide preprogrammed test
routines. The test routines include Auto Mode testing,
which automatically preforms a pre programmed
sequenced of tests, or Manual Mode testing, which
allows the operator to select and run any of the
individual tests.
Container ID Change
Software Upgrades
Alarm Activity
Battery Low (Battery Pack)
Data Retrieval
Defrost Start and End
Dehumidification Start and End
Power Loss (w/wo battery pack)
Power Up (w/wo battery pack)
Remote Probe Temperatures in the Container
(USDA Cold treatment and Cargo probe recording)
Return Air Temperature
Set Point Change
Supply Air Temperature
CAUTION
Pre-trip inspection should not be performed
with critical temperature cargoes in the con-
tainer.
CAUTION
When Pre-Trip key is pressed, economy, de-
humidification and bulb mode will be deac-
tivated. At the completion of Pre-Trip activi-
ty, economy, dehumidification and bulb
mode must be reactivated.
Real Time Clock Battery (Internal Battery) Replace-
ment
Real Time Clock Modification
Trip Start
ISO Trip Header (When entered via Interrogation
program)
Testing may be initiated by use of the Key Pad or via
communication, but when initiated by communication
the controller will execute the entire battery of tests
(auto mode).
At the end of a pre-trip test, the message “P,” “rSLts”
(pretest results) will be displayed. Pressing the ENTER
key will allow the user to see the results for all subtests.
The results will be displayed as “PASS” or “FAIL” for
all the tests run to completion.
Economy Mode Start and End
“Auto 2” Pre-Trip Start and End
Bulb Mode Start
Bulb Mode changes
Bulb Mode End
A detailed description of the pre-trip tests and test codes
is provided in Table 3-7. detailed operating instructions
are provided in paragraph 4.7.
USDA Trip Comment
Humidification Start and End
USDA Probe Calibration
3.6.2 DataCORDER Software
3.6 DataCORDER
3.6.1 Des cription
The DataCORDER Software is subdivided into the
Configuration Software, Operational Software and the
Data Memory.
The Carrier Transicold “DataCORDER,” software is
integrated into the controller and serves to eliminate the
temperature recorder and paper chart. The
DataCORDER functions may be accessed by key pad
selections and viewed on thedisplay module. Theunitis
also fitted with interrogation connections (see
Figure 3- 1) which may be used with the Carrier
Transicold Data Reader to down load data. A personal
computer with Carrier Transicold Data View software
may also be used to download data and configure
settings. The DataCORDER consists of:
a. Operational Software
The Operational Software reads and interprets inputs
for use by the Configuration Software. The inputs are
labeled Function Codes. There are 35 functions (see
Table 3-8) which the operator may access to examine
the current input data or stored data. To access these
codes, do the following:
1 Press the ALT. MODE & CODE SELECT keys.
Configuration Software
Operational Software
Data Storage Memory
Real Time Clock (with internal battery backup)
Six thermistor inputs
2 Press an arrow key until the left window displays the
desired code number. The right window will display
the value of this item for five seconds before return-
ing to the normal display mode.
Interrogation Connections
Power supply (battery pack).
3 If a longer time is desired, press the ENTER key to
extend the time to 30 seconds.
T-309
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-2 DataCORDER Configuration Variables
TITLE
CONFIGURATION NO.
DEFAULT
OPTION
-- --
dCF01
(Future Use)
-- --
2
dCF02
Sensor Configuration
2,5,6,9,54,64,94
15,30,60,120
Low, Normal
A,b,C
dCF03
Logging Interval (Minutes)
60
Short
A
dCF04
Thermistor Format
dCF05
Thermistor Sampling Type
dCF06
Controlled Atmosphere/Humidity Sampling Type
Alarm Configuration USDA Sensor 1
Alarm Configuration USDA Sensor 2
Alarm Configuration USDA Sensor 3
Alarm Configuration Cargo Sensor
A
A,b
dCF07
dCF08
A
Auto, On, Off
Auto, On, Off
Auto, On, Off
Auto, On, Off
A
dCF09
A
dCF10
A
b. Configuration Software
5. Phase A current
6. Phase B current
7. Phase C current
8. Main voltage
9. Suction modulation valve percentage
10. Discrete outputs (Bit mapped -- require special
handling if used)
11. Discrete inputs (Bit mapped -- require special
handling if used)
12. Ambient sensor
13. Compressor suction sensor
14. Compressor discharge sensor
15. Return temperature sensor
16. Supply temperature sensor
17 Defrost temperature sensor
18. Discharge pressure transducer
19. Suction pressure transducer
20. Condenser pressure transducer
The configuration software controls the recording and
alarm functions of the DataCORDER. Reprogramming
to the factory installed configuration is achieved via the
same configuration card as the unit control module
software. Changes to the unit DataCORDER
configuration may be made made using the Data View
integration device. A listing of the configuration
variables is provided in Table 3-2. Descriptions of
DataCORDER operation for each variable setting are
provided in the following paragraphs.
3.6.3 Sens or Configuration (dCF02)
Two modes of operation may be configured, the
Standard Mode and the Generic Mode.
a. Standard Mode
In the standard mode, the user may configure the
DataCORDER to record data using one of seven
standard configurations. Standard configuration
variables, with descriptions, are listed in Table 3-3.
The six thermistor inputs (supply, return, USDA #1, #2,
#3 and cargo probe) and the humidity sensor input will
be generated by the DataCORDER. An example of a
report using a standard configuration is shown in
Figure 3- 5.
Table 3-3 DataCORDER Standard Configurations
Standard
Des cription
Config.
2 sensors
2 thermistor inputs(supply & return)
(dCF02=2)
5 sensors 2 thermistor inputs(supply & return)
(dCF02=5) 3 USDA thermistor inputs
NOTE
2 thermistor inputs(supply & return)
The DataCORDER software uses the supply
and return recorder sensors (SRS,RRS). The
temperature control software uses the supply
and return temperature sensors (STS,RTS) .
6 sensors
3 USDA thermistor inputs
(dCF02=6)
1 humidity input
9 sensors
Not Applicable
(dCF02=9)
b. Generic Mode
2 thermistor inputs(supply & return)
6 sensors
3 USDA thermistor inputs
(dCF02=54)
The generic recording mode allows user selection of the
network data points to be recorded. The user may select
up to a total of eight data points for recording. A list of
the data points available for recording follows.
Changing the configuration to generic and selecting
which data points to record may be done using the
Carrier Transicold Data Retrieval Program.
1 cargo probe (thermistor input)
2 thermistor inputs(supply & return)
3 USDA thermistor inputs
7 sensors
(dCF02=64) 1 humidity input
1 cargo probe (thermistor input)
2 thermistor inputs(supply & return)
3 USDA thermistor inputs
1. Control mode
2. Control temperature
3. Frequency
10 sensors
(dCF02=94)
1 humidity input
1 cargo probe (thermistor input)
3 C.A. inputs (NOT APPLICABLE)
4. Humidity
T-309
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Raw Data Report for ABC1234567
May 31, 2001 to Jun 04, 2001
System Configuration at the Time of Interrogation:
Interrogated On Sept 05, 2001
Extracted by DataLine Rev 1.0.0
Controller Software: 5120
Controller Serial #: 04163552
Bill of Lading #: 1
Origin:
Origin Date:
Destination:
Discharge Date:
Comment: DataLine Tool
Probe Calibration Readings: USDA1: 0.0 USDA2: 0.0 USDA3: 0.0 Cargo: 0
Temperature Units: Centigrade
____________________________________________________________________________________
May 31, 2001
Setpoint: 1.66, Container :
Serial :
9 Sensors Logged at 15 Minute Interval
Sensor
Format
Resolution
Figure 3- 5 Standard Configuration Download Report
T-309
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6.4 Logging Interval (dCF03)
2. Controller DC battery packpower: If a battery pack
is installed, the DataCORDER will power up for
communication when an interrogation cable is plugged
into an interrogation receptacle.
The user may select four different time intervals
between data recordings. Data is logged at exact
intervals in accordance with the real time clock. The
clock is factory set at Greenwich Mean Time (GMT).
3. External DC battery pack power: A 12 volt battery
pack may also be plugged into the back of the
interrogation cable, which is then plugged into an
interrogation port. No controller battery pack is
required with this method.
3.6.5 Thermistor Format (dCF04)
The user may configure the format in which the
thermistor readings are recorded. The short resolution is
a1 byteformat and thelong resolutionis a2 byteformat.
Theshort requires less memory and records temperature
in 0.25°C (0.45°F)steps when in theperishable modeor
0.5°C (0.9°F) steps when in the frozen mode. The long
records temperature in 0.01°C (0.02°F) steps for the
entire range.
4. Real Time Clock demand: If the DataCORDER is
equipped with a charged battery pack and AC power is
not present, the DataCORDER will power up when the
real time clock indicates that a data recording should
take place. When the DataCORDER is finished
recording, it will power down.
3.6.6 Sampling Type (dCF05 & dCF06)
During DataCORDER power-up, while using
battery-pack power, the controller will perform a
hardware voltage check on the battery. If the hardware
check passes, the Controller will energize and performa
software battery voltage check before DataCORDER
logging. If either test fails, the real time clock battery
power-up will be disabled until the next AC power
cycle. Further DataCORDER temperature logging will
be prohibited until that time.
Three types of data sampling are available, average,
snapshot and USDA. When configured to average, the
average of readings taken every minute over the
recording period is recorded. When configured to
snapshot, the sensor reading at the log intervale time is
recorded. When USDA is configured the supply and
return temperature readings are averaged and the 3
USDA probe readings are snapshot.
3.6.7 Alarm Configuration (dCF07 -- dCF10)
An alarm will be generated when the battery voltage
transitions from good to bad indicating that the battery
pack needs recharging. If the alarm condition persists
for more than 24 hours on continuous AC power, the
battery pack needs replacement.
The USDA and cargo probe alarms may be configured
to OFF, ON or AUTO.
If a probe alarm is configured to OFF, then the alarm for
this probe is always disabled.
3.6.9 Pre-Trip Data Recording
If a probe alarm is configured to ON, then the associated
alarm is always enabled.
The DataCORDER will record the initiation of a
pre-trip test (refer to paragraph 3.5) and the results of
each of the tests included in pre--trip. The data is
time-stamped and may be extracted via the Data
Retrieval program. Refer to Table 3-9 for a description
of the data stored in the DataCORDER for each
corresponding Pre-Trip test.
If the probes are configured to AUTO, they act as a
group. This function is designed to assist users who
keep their DataCORDER configured for USDA
recording, but do not install the probes for every trip. If
all the probes are disconnected, no alarms are activated.
As soon as one of the probes is installed , then all of the
alarms are enabled and theremaining probes that arenot
installed will give active alarm indications.
3.6.10 DataCORDER Communications
The DataCORDER will record the initiation of a
pre-trip test (refer to paragraph 3.5) and the results of
each of the tests included in pre--trip. The data is
time-stamped and may be extracted via the Data
Retrieval program. Refer to Table 3-9 for a description
of the data stored in the DataCORDER for each
corresponding Pre-Trip test.
Data retrieval from the DataCORDER can be
accomplished by using one of the following;
DataReader, DataLine/DataView or a communications
interface module.
a. DataReader
The Carrier Transicold Data Reader (see Figure 3- 6) is
a simple to operate hand held device designed to extract
data from the DataCORDER and then upload it to a
personal computer. The Data Reader has the ability to
store multiple data files. Refer to Data Retrieval manual
62-02575 for a more detailed explanation of the
DataReader
3.6.8 DataCORDER Power-Up
The DataCORDER may be powered up in any one of
four ways:
1. Normal AC power: The DataCORDER is powered
up when the unit is turned on via the stop-start switch.
T-309
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Exposing infested fruit to temperatures of 2.2 degrees
Celsius (36_F) or below for specific periods results in
the mortality of the various stages of this group of
insects.
In response to the demand to replace fumigation with
this environmentally sound process, Carrier has
integrated Cold Treatment capability into its
microprocessor system. These units have the ability to
maintain supply air temperature within one-quarter
degree Celsius of setpoint and record minute changes in
product temperature within the DataCORDER
memory, thus meeting USDA criteria. Information on
USDA is provided in the following subparagraphs
DataReader
a. USDA Recording
A special type of recording is used for USDA cold
treatment purposes. Cold treatment recording requires
three remote temperature probes be placed at prescribed
locations in the cargo. Provision is made to connect
these probes to the DataCORDER via receptacles
located at the rear left-hand side of the unit. Four or five
receptacles are provided. The four three-pin receptacles
are for the probes. The five pin receptacle is the rear
connection for the Interrogator. The probe receptacles
are sized to accept plugs with tricam coupling locking
devices. A label on the back panel of the unit shows
which receptacle is used for each probe.
Figure 3- 6 Data Reader
b. DataView
The DataView software for a personal computer is
supplied on a floppy disk. This software allows
interrogation, configuration variable assignment,
screen view of the data, hard copy report generation,
cold treatment probe calibration, cold treatment
initialization and file management. Refer to Data
Retrieval manual 62-02575 for a more detailed
explanation of the DataView interrogation software.
The standard DataCORDER report displays the supply
and return air temperatures. The cold treatment report
displays USDA #1, #2, #3 and the supply and return air
temperatures. Cold treatment recording is backed up by
a battery so recording can continue if AC power is lost.
c. Communications Interface Module
b. USDA/ Mes s age Trip Comment
The communications interface module is a slave
module which allows communication with a master
central monitoring station. The module will respond to
communication and return information over the main
power line.
A special feature is incorporated in DataLine/DataView
which allows the user to enter a USDA (or other)
message in the header of a data report. The maximum
message length is 78 characters. Only one message will
be recorded per day.
With a remote monitoring unit installed, all functions
and selectable features that are accessible atthe unitmay
be performed at the master station. Retrieval of all
DataCORDER reports may also be performed. Refer to
the master system technical manual for further
information.
3.6.12 USDA Cold Treatment Procedure
The following is a summary of the steps required to
initiate a USDA Cold Treatment.
a. Calibrate the three USDA probes by ice bathing the
probes and performing the calibration function with
the DataReader, DataView or DataLine. This calibra-
tion procedure determines the probe offsets and
stores them in the controller for use in generating the
cold treatment report. Refer to the Data Retrieval
manual 62-02575 for more details.
d. DataLine
The DataLINE software for a personal computer is
supplied on both floppy disks and CD. This software
allows
interrogation,
configuration
variable
assignment, screen view of the data, hard copy report
generation, cold treatment probe calibration and file
management. Refer to Data Retrieval manual 62-10629
for a more detailed explanation of the DataLINE
interrogation software. The DataLine manual may be
b. Pre-cool the containerto thetreatment temperatureor
below.
c..Install the DataCORDER module battery pack (if not
already installed).
3.6.11 USDA Cold Treatment
Sustained cold temperature has been employed as an
effective postharvest method for the control of
Mediterranean and certain other tropical fruit flies.
d. Place the three probes. The probes are placed into the
pulp ofthe product (at thelocations defined in thefol-
lowing table) as the product is loaded.
T-309
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
have to be inactive in order to clear the alarm list. To
Clear the Alarm List:
Place in pulp of the product located next
to the return air intake.
Sensor 1
Sensor 2
Place in pulp of the product five feet
from the end of the load for 40 foot con-
tainers, or three feet from the end of the
load for 20 foot containers. This probe
should be placed in a center carton at
one-half the height of the load.
1. Press the ALT. MODE & ALARM LIST keys.
2. Press the UP/DOWN ARROW key until “CLEAr” is
displayed.
Place in pulp of product five feet from
the end of the load for 40 foot containers
or three feet from the end of the load for
20 foot containers. This probe should be
placed in a carton at a side wall at one-
half the height of the load.
3. Press the ENTER key. The alarm list will clear and
“-- -- -- -- -- ” will be displayed.
Sensor 3
4. Press the ALARM LIST key. “AL” will show on the
left display and “-- -- -- -- -- ”on theright display when
there are no alarms in the list.
e. To initiate USDA Recording, connect the personal
computer and perform the configuration as follows,
using either the Data View or Data Line software:
1. Enter ISO header information
2. Enter a trip comment if desired
5. Upon clearing of the Alarm Queue, the Alarm light
will be turned off.
3. Configure the DataCORDER for five probes (s, r,
P1, P2, P3) (dcf02=5)
3.6.14 ISO Trip Header
4. Configure the logging interval for one hour.
5. Set the sensor configuration to “USDA”.
6. Configure for two byte memory storage format
(dcf04=LONG).
7. Perform a “trip start”
3.6.13 DataCORDER Alarms
DataLine provides the user with an interface to
view/modify current settings of the ISO trip header
through the ISO Trip Header screen.
The ISO Trip Header screen is displayed when the user
clicks on the “ISO Trip Header” button in the “Trip
Functions” Group Box on the System Tools screen.
The alarm display is an independent DataCORDER
function. If an operating parameter is outside of the
expected range or a component does not return the
correct values back to the DataCORDER an alarm is
generated. The DataCORDER contains a buffer of up to
eight alarms. A listing of the DataCORDER alarms is
provided in Table 3-10, page 3-27. Refer to paragraph
3.6.7 for configuration information.
F9 function -- Provides the user with a shortcut for
manually triggering the refresh operation.Before
sending modified parameter values, the user must
ensure that a successful connection is established with
the Controller.
If the connection is established with the DataCorder, the
current contents of the ISO Trip Header from the
DataCorder will be displayed in each field. If the
connection is not established with the DataCorder, all
fields on the screen will be displayed as “X’s”.If at any
time during the display of the ISO Trip Header screen
the connection is not established or is lost, the user is
alerted to the status of the connection.
To display alarm codes:
a. While in the Default Display mode, press the ALT.
MODE & ALARM LIST keys. This accesses the Da-
taCORDER Alarm List Display Mode, which dis-
plays any alarms stored in the Alarm Queue.
b. To scroll to the end of the alarm list press the UP AR-
ROW. Depressing the DOWN ARROW key will
scroll the list backward.
c. The left display will show “AL#” where # is the
alarms number in the queue. The right display will
show “AA##,” if the alarm is active, where ## is the
alarm number. “IA##,” will show if the alarm is inac-
tive
After modifying the values and ensuring a successful
connection has been made with the DataCorder, click on
the “Send” button to send the modified parameter
values.
d. “END” is displayed to indicate the end of the alarm
list if any alarms are active. “CLEAr” is displayed if
all the alarms in the list are inactive.
e. If no alarms are active, the Alarm Queue may be
cleared. The exception to this rule is the DataCORD-
ER Alarm Queue Full alarm (AL91) , which does not
The maximum allowed length of the ISO Trip Header is
128 characters.If the user tries to refresh the screen or
close the utility without sending the changes made on
the screen to the DataCorder, the user is alerted with a
message.
T-309
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-4 Controller Configuration Variables
NOTES
1. Configuration numbers not listed are not used in this application. These items may appear when loading
configuration software to the controller but changes will not be recognized by the controller programming.
CONFIGURATION
TITLE
Evaporator Fan Speed
DEFAULT
dS (Dual)
OPTION
SS (Single)
NUMBER
CnF02
CnF04
CnF11
CnF16
CnF22
CnF23
CnF24
CnF25
CnF26
CnF28
CnF31
CnF33
CnF34
CnF37
Dehumidification Mode
On
OFF
Defrost “Off” Selection
noOFF
On (Yes)
OFF
OFF
DataCORDER Present
OFF (No)
Std, Full
SAv
Economy Mode Option
Defrost Interval Timer Save Option
Long Pre Trip Test Sequence Enabled
Pre-Trip Test Points/Results Recording Option
Heat Lockout Change Option
Bulb Mode Option
noSAv
On
Off
rSLtS
dAtA
Set to --10_C
NOr
Set to --5_C
bULb
Probe Check Option
Std
SPEC
SnAP
Snap Freeze Option
OFF
Degree Celsius Lockout Option
Electronic Temperature Recorder
bOth
_F
rEtUR (Return)
suPPl, BOth
T-309
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-5 Controller Function Codes (Sheet 1 of 3)
DESCRIPTION
Code
No.
TITLE
Note: If the function is not applicable, the dis play will read “-- -- -- -- -- ”
Dis play Only Functions
Displays the SMV percent open. The right display reads 100% when the valve is
fully open. The valve will usually be at 10% on start up of the unit except in very
high ambient temperatures.
Suction Modulation
Valve Opening (%)
Cd01
Cd02 Not Applicable
Not used
The current sensor measures current draw in lines L1 & L2 by all of the high
voltage components. It also measures current draw in compressor motor leg T3.
The compressor leg T3 current is displayed.
Compressor Motor
Current
Cd03
The current sensor measures current on two legs. The third unmeasured leg is cal-
culated based on a current algorithm. The current measured is used for control
and diagnostic purposes. For control processing, the highest of the Phase A and B
current values is used for current limiting purposes. For diagnostic processing,
the current draws are used to monitor component energization.. Whenever a heat-
er or a motor is turned ON or OFF, the current draw increase/reduction for that
activity is measured. The current draw is then tested to determine if it falls within
the expected range of values for the component. Failure of this test will result in a
pre-trip failure or a control alarm indication.
Cd04 Line Current,
Phase A
Cd05 Line Current,
Phase B
Cd06 Line Current,
Phase C
Cd07 Main Power Voltage The main supply voltage is displayed.
Main Power Fre-
quency
The value of the main power frequency is displayed in Hertz. The frequency dis-
Cd08
Cd09
Cd10
Cd11
Cd12
played will be halved if either fuse F1 or F2 is bad (alarm code AL21).
Ambient Tempera-
ture
The ambient sensor reading is displayed.
Compressor Suction
Temperature
Compressor suction temperature sensor reading is displayed.
Compressor discharge temperature sensor reading is displayed.
Compressor Dis-
charge Temperature
Compressor Suction
Pressure
Compressor suction pressure transducer reading is displayed.
Not used
Cd13 Not Applicable
Compressor Dis-
Cd14
Compressor discharge pressure transducer reading is displayed.
charge Pressure
Cd15 Unloader Valve
The status of the valve is displayed (Open - Closed).
Compressor Motor
Cd16
Records total hours of compressor run time. Total hours are recorded in incre-
ments of 10 hours (i.e., 3000 hours is displayed as 300).
Hour Meter
Relative Humidity
Humidity sensor reading is displayed. This code displays the relative humidity, as
a percent value.
Cd17
(%)
Cd18 Software Revision # The software revision number is displayed.
This code checks the Controller/DataCORDER battery pack. While the test is
running, “btest” will flash on the right display, followed by the result. “PASS”
will be displayed for battery voltages greater than 7.0 volts. “FAIL” will be dis-
played for battery voltages between 4.5 and 7.0 volts, and “-- -- -- -- -- ” will be
displayed for battery voltages less than 4.5 volts. After the result is displayed for
four seconds, “btest” will again be displayed, and the user may continue to scroll
through the various codes.
Cd19 Battery Check
This code indicates the dash number of the model for which the Controller is con-
figured (i.e., if the unit is a 69NT40-531-100, the display will show “31100”).
Cd20 Config/Model #
Cd21 Economizer Valve
The status of the valve is displayed (Open - Closed).
T-309
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-5 Controller Function Codes (Sheet 2 of 3)ff
Cd22 Compressor State
Cd23 Evaporator Fan
The status of the compressor is displayed (Off, On).
Displays the current evaporator fan state (high, low or off).
Controlled
Cd24
Not used in this application
Atmosphere State
Compressor Run
This code displays the time remaining until the unit goes into defrost (in tenths of
an hour). This value is based on the actual accumulated compressor running time.
Time Remaining
Until Defrost
Cd25
Cd26
Defrost Temperature
Sensor Reading
Defrost temperature sensor reading is displayed.
Configurable Functions
NOTE
Function codes Cd27 through Cd37 are user-selectable functions. The operator can change the value of
these functions to meet the operational needs of the container.
The defrost interval is the time between defrost cycles. Five selectable values are
available: 3, 6, 9, 12 or 24 hours. The factory default value is 12 hours. Follow-
ing a start--up or after termination of a defrost, the time will not begin counting
down until the defrost temperature sensor (DTS) reading falls below set point. If
the reading of DTS rises above set point any time during the timer count down,
the interval is reset and the countdown begins over. If DTS fails, alarm code
AL60 is activated and control switches over to the the return temperature sensor.
The controller will act in the same manner as with the DTS except the return tem-
Defrost Interval
(Hours)
perature sensor reading will be used.
Cd27
Defrost Interval Timer Value (Configuration variable CnF23): If the software is
configured to “SAv” (save) for this option, then the value of the defrost interval
timer will be saved at power down and restored at power up. This option prevents
short power interruptions from resetting an almost expired defrost interval, and
possibly delaying a needed defrost cycle.
NOTE
The defrost interval timer counts only during compressor run time.
This code determines the temperature units (_C or _F) which will be used for all
temperature displays. The user selects _C or _F by selecting function code Cd28
and pushing the ENTER key. The factory default value is Celsius units.
Temperature Units
(_C or _F)
Cd28
NOTE
This function code will display “--- --- --- --- --- “ if Configuration Variable
CnF34 is set to _F.
If all of the control sensors are out of range (alarm code AL26) or there is a probe
circuit calibration failure (alarm code AL27), the unit will enter the shutdown
state defined by this setting. The user selects one of four possible actions as fol-
lows:
A -- Full Cooling (compressor is on, economized operation. SMVsubject to pressure
Failure Action
(Mode)
and current limit.)
Cd29
B -- Partial Cooling (Compressor is on, standard operation. SMV subject to pressure
and current limit.)
C -- Evaporator Fan Only (Compressor is off, evaporator fans on high speed, not ap-
plicable with frozen set points.
D -- Full System Shutdown -- Factory Default (shut down every component in the
unit)
The in-range tolerance will determine the band of temperatures around the set
point which will be designated as in-range. If the control temperature is in-range,
the in-range light will be illuminated. There are four possible values:
1 = ¦ 0.5_C (¦ 0.9_F)
Cd30 In-Range Tolerance
2 = ¦ 1.0_C (¦ 1.8_F)
3 = ¦ 1.5_C (¦ 2.7_F)
4 = ¦ 2.0_C (¦ 3.6_F) -- Factory Default
T-309
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-5 Controller Function Codes (Sheet 3 of 3)
The stagger start offset time is the amount of time that the unit will delay at start-
up, thus allowing multiple units to stagger their control initiation when all units
are powered up together. The eight possible offset values are:
Stagger Start Offset
Time (Seconds)
Cd31
Cd32
0 (Factory Default), 3, 6, 9, 12, 15, 18 or 21 seconds
The current limit is the maximum current draw allowed on any phase at any time.
Limiting the unit’s current reduces the load on the main power supply. This is
accomplished by reducing the SMV position until current draw is reduced to the
set point. When desirable, the limit can be lowered. Note, however, that capacity
is also reduced. The five values for 460vac operation are: 15, 17, 19, 21 (Factory
Default), 23
Current Limit
(Amperes)
Relative humidity set point is available only on units configured for dehumidifi-
cation. When the mode is activated, the control probe LED flashes on and off ev-
ery second to alert the user. If not configured, the mode is permanently deacti-
vated and “-- -- -- -- -- ” will display. The value can be set to “OFF.” “TEST,” or a
range of 65 to 95% relative humidity in increments of 1%. [If bulb mode is active
(code Cd35) and “Lo” speed evaporator motors are selected (code Cd36) then set
point ranges from 60 to 95%.] When “TEST” is selected or test set point is
entered, the heat LED should illuminate, indicating that dehumidification mode is
activated. After a period of five minutes in the “TEST” mode has elapsed, the
previously selected mode is reinstated.
Perishable Mode
Dehumidification
Control (% RH)
Cd33
Cd34
Economy Mode
(On--Off)
Economy mode is a user selectable mode of operation provided for power saving
purposes.
Bulb mode is a user selectable mode of operation that is an extension of dehu-
midification control (Cd33). If dehumidification is set to “Off,” code Cd35 will
display “Nor” and the user will be unable to change it. After a dehumidification
set point has been selected and entered for code Cd33, the user may then change
code Cd35 to “bulb.” After bulb has been selected and entered, the user may then
utilize function codes Cd36 and Cd37 to make the desired changes.
Cd35 Bulb Mode
This code is enabled only if in the dehumidification mode (code Cd33) and bulb
mode (Cd35) has been set to “bulb”. If these conditions are not met, “alt” will be
displayed (indicating that the evaporator fans will alternate their speed) and the
display cannot be changed. If a dehumidification set point has been selected along
with bulb mode then “alt” may be selected for alternating speed, “Lo” for low
speed evaporator fan only, or “Hi” for high speed evaporator fan only. If a setting
other than “alt” has been selected and bulb mode is deactivated in any manner,
then selection reverts back to “alt.”
Evaporator Speed
Select
Cd36
This code, as with function code Cd36, is used with bulb mode and dehumidifica-
tion. If bulb mode is active, this code allows the user to change the temperature
defrost will terminate. It allows the user to change the setting within a range of
4_C to 25.6_C in 0.1_C (0.2_F) increments. This value is changed using the UP/
DOWN ARROW keys, followed by the ENTER key when the desired value is
displayed. If bulb mode is deactivated, the DTS setting returns to the default.
Defrost Termination
Temperature Setting
(Bulb Mode)
Cd37
Cd38
Dis play Only Functions -- Continued
Code Cd38 will display the current secondary supply temperature sensor reading
for units configured for four probes. If the unit is configured with a DataCORD-
Secondary Supply
Temperature Sensor ER, Cd38 will display “-- -- -- -- -- .” If the DataCORDER suffers a failure,
(AL55) Cd38 will display the supply recorder sensor reading.
Code Cd39 will display the current secondary return temperature sensor reading
for units configured for four probes. If the unit is configured with a DataCORD-
Secondary Return
Cd39
Cd40
Temperature Sensor ER, Cd39 will display “-- -- -- -- -- .” If the DataCORDER suffers a failure,
(AL55) Cd39 will display the return recorder sensor reading.
Code Cd40 is configured at commissioning to read a valid container identifica-
Container Identifica-
tion Number
tion number. The reading will not display alpha characters, only the numeric por-
tion of the number will display.
SERVICE FUNCTION: This code is used for troubleshooting and allows manu-
al positioning of the economizer, unloader, suction modulation and oil return
valves. Refer to paragraph 6.19 for operating instructions.
Cd41 Valve Override
Cd42 Oil Return Valve
The status of the valve is displayed (Open - Closed).
T-309
3-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-6 Controller Alarm Indications (Sheet 1 of 4)
DESCRIPTION
Code
No.
TITLE
Alarm 13 is triggered if the control module has lost communication with the ex-
pansion module for more than five minutes or communication fails within the
first 15 seconds on power up. This alarm triggers failure action C (evaporator fan
only) or D (all machinery off) of Function Code Cd29 if the unit has a perishable
set point. Failure action D (all machinery off) is triggered if the unit has a frozen
set point
AL13 Expansion Module
Alarm 14 is triggered if the electronic phase detection system is unable to deter-
mine the correct phase relationship. DIRCHECK will be displayed while the
relationship is determined. If the system is unable to determine the proper rela-
tionship alarm 14 will remain active. Additiotnal information on phase detection
may be displayed at Function Code Cd41. If the right most digit of Code Cd41 is
3 or 4, this indicates incorrect motor or sensor wiring. If the right most digit is 5,
this indicates a failed current sensor assembly.
Phase Sequence
AL14
Failure -- Electronic
AL15 Loss Cooling
Future Expansion
Alarm 16 is triggered if compressor current draw is 15% over calculated maxi-
mum for 10 minutes out of the last hour. The alarm is display only and will trig-
ger off when the compressor operates for one hour without over current.
Compressor Current
AL16
High
Alarm 17 is triggered if a compressor start in both directions fails to generate
sufficient pressure differential. The controller will attempt restart every twenty
minutes and deactivate the alarm if successful. This alarm triggers failure action
C (evaporator fan only) or D (all machinery off) of Function Code Cd29 if the
unit has a perishable set point. Failure action D (all machinery off) is triggered if
the unit has a frozen set point
Phase Sequence
AL17
Failure -- Pressure
Alarm 18 is triggered if discharge pressure is 10% over calculated maximum for
10 minutes within the last hour. The alarm is display only and will trigger off
when the compressor operates for one hour without overpressure.
Discharge Pressure
AL18
High
Alarm 19 is triggered if discharge temperature exceeds 135_C (275_F) for 10
minutes within the last hour. The alarm is display only and will trigger off when
the compressor operates for one hour without over temperature.
Discharge Tempera-
ture High
AL19
Alarm 20 is triggered by control power fuse (F3) opening and will cause the soft-
ware shutdown of all control units. This alarm will remain active until the fuse is
replaced.
Control Circuit Fuse
AL20
Open (24 vac)
Alarm 21 is triggered by one of the fuses (F1/F2) being opened on 18 volts AC
power supply to the Controller. The suction modulation valve (SMV) will be
opened and current limiting is halted. Temperature control will be maintained by
cycling the compressor.
Micro Circuit Fuse
AL21
Open (18 vac)
Alarm 22 responds to the evaporator motor internal protectors. The alarm is trig-
gered by opening of either internal protector. It will disable all control units until
the motor protector resets and the unit is power cycled.
Evaporator Fan Mo-
tor Safety
AL22
Alarm 23 is triggered if low current draw is detected on phase B and IPCP, HPS
or IPEM is not tripped. If the compressor should be running, the controller will
initiate a start up every five minutes and trigger off if current reappears. If the
evaporator fan motors only should be running, the alarm will trigger off is cur-
rent reappears. This alarm triggers failure action C (evaporator fan only) or D
(all machinery off) of Function Code Cd29 if the unit has a perishable set point.
Failure action D (all machinery off) is triggered if the unit has a frozen set point
AL23 Loss of Phase B
Alarm 24 is triggered when compressor is not drawing any current. It also trig-
gers failure action ”C” or ”D” set by function Code 29 for perishable setpoint, or
”D” for frozen setpoint. This alarm will remain active until compressor draws
current.
Compressor Motor
AL24
Safety
T-309
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-6 Controller Alarm Indications (Sheet 2 of 4)
Alarm 25 is triggered by the opening of the condenser motor internal protector
and will disable all control units except for the evaporator fans. This alarm will
remain active until the motor protector resets. This alarm triggers failure action
C (evaporator fan only) or D (all machinery off) of Function Code Cd29 if the
unit has a perishable set point. Failure action D (all machinery off) is triggered if
the unit has a frozen set point
Condenser Fan Mo-
tor Safety
AL25
AL26
AL27
All Supply and Re- Alarm 26 is triggered if the Controller determines that all of the control sensors
turn temperature
Control Sensors
Failure
are out-of-range. This can occur for box temperatures outside the range of --50_C
to +70_C (--58_F to +158_F). This alarm triggers the failure action code set by
Function Code Cd29.
The Controller has a built-in Analog to Digital (A-D) converter, used to convert
analog readings (i.e. temperature sensors, current sensors, etc.) to digital read-
ings. The Controller continuously performs calibration tests on the A-D con-
verter. If the A-D converter fails to calibrate for 30 consecutive seconds, this
alarm is activated.This alarm will be inactivated as soon as the A-D converter
calibrates.
A/D Accuracy Fail-
ure
Alarm 28 is triggered if suction pressure is below 2 psia and alarm 66 (Suction
Pressure Transducer Failure) is not active. This alarm will be inactivated when
suction pressure rises above 2 psia for three continuous minutes. This alarm trig-
gers failure action C (evaporator fan only) or D (all machinery off) as determined
by User Selectable Failure Response if the unit has a perishable set point; Failure
action D (all machinery off) if the unit has a frozen set point. Reset SMV.
Low Suction Pres-
sure
AL28
During start-up diagnostics, the EEPROM is examined to determine validity of
its contents. This is done by testing the set point and the alarm list. If the con-
tents are invalid, Alarm 51 is activated. During control processing, any operation
involving alarm list activity that results in an error will cause Alarm 51 to be ac-
tivated. Alarm 51 is a “display only” alarm and is not written into the alarm list.
Pressing the ENTER key when “CLEAr” is displayed will result in an attempt to
clear the alarm list. If that action is successful (all alarms are inactive), Alarm 51
will be reset.
AL51 Alarm List Failure
Alarm 52 is activated whenever the alarm list is determined to be full; at start-up
or after recording an alarm in the list. Alarm 52 is displayed, but is not recorded
in the alarm list. This alarm can be reset by clearing the alarm list. This can be
done only if all alarms written in the list are inactive.
AL52 Alarm List Full
Alarm 53 is caused by the battery pack charge being too low to provide sufficient
power for battery-backed recording. Renew replaceable batteries. If this alarm
occurs on start up, allow a unit fitted with rechargeable batteries to operate for up
to 24 hours to charge rechargeable batteries sufficiently to deactivate the alarm
AL53 Battery Pack Failure
Alarm 54 is activated by an invalid primary supply temperature sensor reading
that is sensed outside the range of --50 to +70_C (--58_F to +158_F) or if the
probe check logic has determined there is a fault with this sensor. If Alarm 54 is
activated and the primary supply is the control sensor, the secondary supply sen-
sor will be used for control if the unit is so equipped. If the unit does not have a
secondary supply temperature sensor, and AL54 is activated, the primary return
sensor reading, minus 2_C will be used for control.
Primary Supply
Temperature Sensor
Failure (STS)
AL54
AL55
NOTE
The P5 Pre-Trip test must be run to inactivate the alarm
This alarm activates to indicate the DataCORDER has a software failure. To
clear this alarm, reconfigure the unit to the current model number. This failure
may be the result of a voltage dip in access of 25%.
DataCORDER
Failure
T-309
3-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-6 Controller Alarm Indications (Sheet 3 of 4)
Alarm 56 is activated by an invalid primary return temperature sensor reading
that is outside the range of --50 to +70_C (--58_F to +158_F). If Alarm 56 is acti-
vated and the primary return is the control sensor, the secondary return sensor
will be used for control if the unit is so equipped. If the unit is not equipped with
a secondary return temperature sensor or it fails, the primary supply sensor will
be used for control.
Primary Return
Temperature Sensor
Failure (RTS)
AL56
NOTE
The P5 Pre-Trip test must be run to inactivate the alarm.
Ambient Tempera-
ture Sensor Failure
Alarm 57 is triggered by an ambient temperature reading outside the valid range
AL57
AL58
from --50_C (--58_F) to +70_C (+158_F).
Alarm 58 is triggered when the compressor high discharge pressure safety switch
remains open for at least one minute. This alarm will remain active until the pres-
sure switch resets, at which time the compressor will restart.
Compressor High
Pressure Safety
Alarm 59 is triggered by the opening of the heat termination thermostat and will
result in the disabling of the heater. This alarm will remain active until the ther-
mostat resets.
Heat Termination
Thermostat
AL59
Alarm 60 is an indication of a probable failure of the defrost temperature sensor
(DTS). It is triggered by the opening of the heat termination thermostat (HTT) or
the failure of the DTS to go above set point within two hours of defrost initia-
tion. After one-half hour with a frozen range set point, or one-half hour of contin-
uous compressor run time, if the return air falls below 7_C (45_F), the Controller
checks to ensure the DTS reading has dropped to 10_C or below. If not, a DTS
failure alarm is given and the defrost mode is operated using the return tempera-
ture sensor. The defrost mode will be terminated after one hour by the Controller.
Defrost Temperature
Sensor Failure
AL60
Alarm 61 is triggered by detection of improper amperage resulting from heater
activation or deactivation. Each phase of the power source is checked for proper
amperage.This alarm is a display alarm with no resulting failure action, and will
be reset by a proper amp draw of the heater.
AL61 Heaters Failure
Alarm 62 is triggered by improper current draw increase (or decrease) resulting
from compressor turn on (or off). The compressor is expected to draw a mini-
mum of 2 amps; failure to do so will activate the alarm. This is a display alarm
with no associated failure action and will be reset by a proper amp draw of the
compressor.
Compressor Circuit
Failure
AL62
Alarm 63 is triggered by the current limiting system. If the compressor is ON
and current limiting procedures cannot maintain a current level below the user
selected limit, the current limit alarm is activated. This alarm is a display alarm
and is inactivated by power cycling the unit, changing the current limit via the
code select Cd32, or if the current decreases below the activation level.
AL63 Current Over Limit
Alarm 64 is triggered if the discharge temperature sensed is outside the range of
-- 6 0 _C (--76_F) to 175_C (347_F), or if the sensor is out of range. This is a dis-
play alarm and has no associated failure action.
Discharge Tempera-
AL64
ture Over Limit
Discharge Pressure Alarm 65 is triggered if a compressor discharge transducer is out of range. This is
AL65
AL66
Transducer Failure
a display alarm and has no associated failure action.
Suction Pressure
Alarm 66 is triggered if a suction pressure transducer is out of range. This is a
display alarm and has no associated failure action.
Transducer Failure
Alarm 67 is triggered by a humidity sensor reading outside the valid range of 0%
to 100% relative humidity. If alarm AL67 is triggered when the dehumidification
mode is activated, then the dehumidification mode will be deactivated.
Humidity Sensor
Failure
AL67
AL69
Alarm 69 is triggered by a suction temperature sensor reading outside the valid
range of --60_C (--76_F) to 150_C (302_F). This is a display alarm and has no
associated failure action.
Suction Temperature
Sensor Failure
T-309
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-6 Controller Alarm Indications (Sheet 4 of 4)
NOTE
If the Controller is configured for four probes without a DataCORDER, the DataCORDER alarms AL70
and AL71 will be processed as Controller alarms AL70 and AL71. Refer to Table 3-10.
The Controller performs self-check routines. if an internal failure occurs, an
“ERR” alarm will appear on the display. This is an indication the Controller
needs to be replaced.
ERROR
DESCRIPTION
Indicates that the Controller working memory has
failed.
ERR 0 -- RAM failure
EER 1 -- Program
Memory failure
Indicates a problem with the Controller program.
Internal
Microprocessor
Failure
ERR
#
EER 2 -- Watchdog
time--out
The Controller program has entered a mode whereby
the Controller program has stopped executing.
EER 3 -- On board timer
failure
The on board timers are no longer operational.
Timed items such as; defrost, etc. may not work.
EER 4 -- Internal counter Internal multi-purpose counters have failed. These
failure
counters are used for timers and other items.
The Controller’s Analog to Digital (A-D) converter
has failed.
EER 5 -- A-D failure
Enter Setpoint
(Press Arrow &
Enter)
Entr
StPt
The Controller is prompting the operator to enter a set point.
Low Main Voltage
(Function Codes
Cd27--38 disabled
and NO alarm
stored.)
This message will be alternately displayed with the set point whenever the sup-
ply voltage is less than 75% of its proper value.
LO
T-309
3-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-7 Controller Pre-Trip Tes t Codes (Sheet 1 of 4)
Code
No.
TITLE
DESCRIPTION
NOTE
“Auto” or “Auto1” menu includes the: P0, P1, P2, P3, P4, P5, P6 and rSLts. “Auto2” menu
includes P0, P1, P2, P3, P4, P5, P6, P7, P8, P9, P10 and rSLts.
All lights and display segments will be energized for five seconds at the start of
the pre-trip. Since the unit cannot recognize lights and display failures, there are
no test codes or results associated with this phase of pre-trip.
P0--0
Pre-Trip Initiated
Setup: Heater must start in the OFF condition, and then be turned on. A current
draw test is done after 15 seconds.
P1-0 Heaters Turned On
P1-1 Heaters Turned Off
Pass/Fail Criteria: Passes if current draw change is within the range specified.
Setup: Heater must start in the ON condition, and then be turned off. A current
draw test is done after 10 seconds.
Pass/Fail Criteria: Passes if current draw change is within the range specified.
Requirements: Water pressure switch or condenser fan switch input must be
closed.
Setup: Condenser fan is turned ON, a current draw test is done after 15 seconds.
Pass/Fail Criteria: Passes if current draw change is within the range specified.
P2-0
Condenser Fan On
Setup: Condenser fan is turned OFF, a current draw test is done after 10 sec-
onds.
Pass/Fail Criteria: Passes if current draw change is within the range specified.
P2-1 Condenser Fan Off
Low Speed Evapora- Requirements: The unit must be equipped with a low speed evaporator fan, as
P3
tor Fans
determined by the Evaporator Fan speed select configuration variable.
Setup: The high speed evaporator fans will be turned on for 10 seconds, then off
for two seconds, then the low speed evaporator fans are turned on. A current
draw test is done after 60 seconds.
Pass/Fail Criteria: Passes if change in current draw is within the range speci-
fied. Fails if AL11 or AL12 activates during test.
Low Speed Evapora-
tor Fan Motors On
P3-0
Setup: The low speed Evaporator Fan is turned off, a current draw test is done
after 10 seconds.
Low Speed Evapora-
P3-1
P4-0
P4-1
tor Fan Motors Off Pass/Fail Criteria: Passes if change in current draw is within the range speci-
fied. Fails if AL11 or AL12 activates during test.
Setup: The high speed Evaporator Fan is turned on, a current draw test is done
after 60 seconds.
High Speed Evapo-
rator Fan Motors On Pass/Fail Criteria: Passes if change in current draw is within the range speci-
fied. Fails if AL11 or AL12 activates during test.
Setup: The high speed Evaporator Fan is turned off, a current draw test is done
after 10 seconds.
High Speed Evapo-
rator Fan Motors Off Pass/Fail Criteria: Passes if change in current draw is within the range speci-
fied. Fails if AL11 or AL12 activates during test.
Setup: The High Speed Evaporator Fan is turned on and run for eight minutes,
with all other outputs de-energized.
Pass/Fail Criteria: A temperature comparison is made between the return and
supply probes.
Supply/Return Probe
P5-0
Test
NOTE
If this test fails, “P5-0” and “FAIL” will be displayed. If both Probe tests
(this test and the PRIMARY/ SECONDARY) pass, the display will read
“P5” “PASS.”
T-309
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-7 Controller Pre-Trip Tes t Codes (Sheet 2 of 4)
Requirements: For units equipped with secondary supply probe only.
Pass/Fail Criteria: The temperature difference between primary and secondary probe
(supply) is compared.
P5-1
Supply Probe Test
NOTE
If this test fails, “P5-1” and FAIL will be displayed. If both Probe tests (this
and the SUPPLY/ RETURN TEST) pass, because of the multiple tests, the
display will read ’P 5’ ’PASS’.
Requirements: For units equipped with secondary return probe only.
Pass/Fail Criteria: The temperature difference between primary and secondary
probe (return) is compared.
NOTES
P5-2
Return Probe Test
1. If this test fails, “P5-2” and “FAIL” will be displayed. If both Probe tests
(this test and the SUPPLY/ RETURN) pass, because of the multiple
tests, the display will read “P 5,” “PASS.”
2. The results of Pre-Trip tests 5-0, 5-1 and 5-2 will be used to activate or
clear control probe alarms.
Setup: The system is operated through a sequence of events to test the compo-
nents. The sequence is: Step 1, de--energize all outputs; Step 2, start unit with
Refrigerant Probes,
Compressor
unloader valve open. Open then close the suction modulation valve. Monitor
suction pressure; Step 3, open suction modulation valve to a known position;
Step 4, close suction modulation valve to a know position; Step 5, open econo-
mizer valve; Step 6, close unloader valve; Step 7, open unloader valve; Step 8,
close economizer valve; Step 9, de--energize all outputs.
P6
and
Refrigeration valves
Discharge
If alarm 64 is activated any time during the first 45 second period of Step 1, the
test fails.
P6-0
P6-1
P6-2
P6-3
P6-4
P6-5
P6-6
Thermistor Test
Suction
Thermistor Test
If alarm 69 is activated any time during the first 45 second period of Step 1, the
test fails.
Discharge Pressure If alarm 65 is activated any time during the first 45 second period of Step 1, the
Sensor Test
test fails.
Suction Pressure
Sensor Test
If alarm 66 is activated any time during the first 45 second period of Step 1, the
test fails.
Compressor Current Compressor current is tested before and after start up. If current does not in-
Draw Test crease, the test fails.
Suction Modulation Suction pressure is measured before and after the valve opens. If suction pres-
Valve Test
sure does not increase, the test fails.
Economizer
Valve Test
Suction pressure is measured during Steps 4 and 5. If suction pressure does not
increase, the test fails.
Suction pressure is measured during Steps 6 and 7. If suction pressure does not
increase, the test fails.
P6-7 Unloader Valve Test
T-309
3-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-7 Temperature Controller Pre-Trip Tes t Codes (Sheet 3 of 4)
NOTE
P7-0 through P10 are included with the “Auto2” only.
NOTE
This test is skipped if the sensed ambient temperature is less than 7_C
(45_F), the return air temperature is less than --17.8_C (0_F), the water
pressure switch is open or the condenser fan switch is open.
P7-0
High Pressure
Switch Closed
Setup: With the unit running, the condenser fan is de-energized, and a 15 minute
timer is started.
Pass/Fail Criteria: The test fails if high pressure switch fails to open in 15 min-
utes.
Requirements: Test P7-0 must pass for this test to execute. Setup: The con-
denser fan is started and a 60 second timer is started.
High Pressure
Switch Open
P7-1
P8-0
Pass/Fail Criteria: Passes the test if the high pressure switch (HPS) closes
within the 60 second time limit, otherwise, it fails.
Setup: If the container temperature is below 15.6°C (60_F), the set point is
changed to 15.6°C, and a 180 minute timer is started. The left display will read
“P8-0.” The control will then heat the container until 15.6°C is reached. If the
container temperature is above 15.6°C at the start of the test, then the test pro-
ceeds immediately to test P8-1 and the left display will change to “P8-1.”
Pass/Fail Criteria: The test fails if the 180 minute timer expires before the con-
trol temperature reaches set point. The display will read “P8-0,” “FAIL.”
Perishable Mode
Heat Test
Requirements: Control temperature must be at least 15.6°C (60_F).
Setup: The set point is changed to 0°C (32_F), and a 180 minute timer is
started. The left display will read “P8-1,” the right display will show the supply
air temperature. The unit will then start to pull down the temperature to the 0°C
set point.
Pass/Fail Criteria: The test passes if the container temperature reaches set point
before the 180 minute timer expires.
Perishable Mode
Pull Down Test
P8-1
Requirements: Test P8-1 must pass for this test to execute. This test is skipped
if the DATAcorder is not configured or available.
Setup: The left display will read “P8-2,” and the right display will show the sup-
ply air temperature. A two hour timer is started. The unit will be required to
maintain the temperature to within + or -- 0.5_C (0.9_F) of set point until a Da-
taCORDER recording is executed. The recorder supply probe temperature run-
ning total (and its associated readings counter) will be zeroed out for the remain-
der of the recording period at the start of this test, so that the actual value
recorded in the DataCORDER will be an average of only this test’s results. Once
a recording interval is complete, the average recorder supply temperature will be
recorded in the DataCORDER, as well as stored in memory for use in applying
the test pass/fail criteria.
Perishable Mode
Maintain Tempera-
ture Test
P8-2
Pass/Fail Criteria: If the recorded temperature is within +/-- 0.5_C. of set point
from test start to DataCORDER recording, the test passes. If the average temper-
ature is outside of the tolerance range at the recording, the test fails and will
auto--repeat by starting P8--0 over.
Setup: The defrost temperature sensor (DTS) reading will be displayed on the
left display. The right display will show the supply air temperature. The unit will
run FULL COOL for 30 minutes maximum until the DTT is considered closed.
Once the DTT is considered closed, the unit simulates defrost by running the
heaters for up to two hours, or until the DTT is considered open.
P9-0
Defrost Test
Pass/Fail Criteria: The test fails if: the DTT is not considered closed after the
30 minutes of full cooling, HTT opens when DTT is considered closed or if re-
turn air temperature rises above 49/50_C (120/122_F).
T-309
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-7 Controller Pre-Trip Tes t Codes (Sheet 4 of 4)
Setup: If the container temperature is below 7.2_C (45_F), the set point is
changed to 7.2_C and a 180 minute timer is started. The control will then be
placed in the equivalent of normal heating. If the container temperature is above
7.2_C at the start of the test, then the test proceeds immediately to test 10--1.
During this test, the control temperature will be shown in the right display.
Pass/Fail Criteria: The test fails if the 180 minute timer expires before the con-
trol temperate reaches set point --0.3_C (0.17_F). If the test fails it will not auto--
repeat. There is no pass display for this test, once the control temperature reaches
set point, the test proceeds to test 10--1
Frozen Mode
Heat Test
P10-0
P10-1
Requirements: Control temperature must be at least 7.2_C (45_F)
Setup: The set point is changed to --17.8_C (0_F). The system will then attempt
to pull don the Control temperature to set point using normal frozen mode cool-
ing. During this test, the control temperate will be shown on the right display
Pass/Fail Criteria: If the control temperature does not reach set point --0.3_C
(0.17_F) before the 180 minute timer expires the test fails and will auto--repeat
by starting P10--0 over..
Frozen Mode Pull
Down Test
Requirements: Test P10-1 must pass for this test to execute. This test is skipped
if the DATAcorder is not configured or available.
Setup: During this test, the left display will read “P10-2,” and the right display
will show the supply air temperature. A two hour timer is started. The unit will
be required to maintain the temperature to within + 0.5_C (0.9_F)/--1.3_C
(2.3_F) of set point until a DataCORDER recording is executed. The recorder
supply probe temperature running total (and its associated readings counter) will
be zeroed out for the remainder of the recording period at the start of this test, so
that the actual value recorded in the DataCORDER will be an average of only
this test’s results. Once a recording interval is complete, the average recorder
supply temperature will be recorded in the DataCORDER, as well as stored in
memory for use in applying the test pass/fail criteria.
Frozen Mode
Maintain
Temperature Test
P10-2
Pass/Fail Criteria: If the recorded temperature is within +0.5_C (0.9_F)/--1.3_C
(2.3_F) of set point from test start to DataCORDER recording, the test passes. If
the average temperature is outside of the tolerance range at the recording, the test
fails and will auto--repeat by starting P10--0 over.
T-309
3-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-8 DataCORDER Function Code As s ignments
NOTE
Inapplicable Functions Display “ -- -- -- -- -- ”
To Acces s : Pres s ALT. MODE key
Code
No.
TITLE
DESCRIPTION
Current reading of the supply recorder sensor.
Current reading of the return recorder sensor.
Recorder Supply
Temperature
dC1
dC2
Recorder Return
Temperature
USDA 1,2,3 Tem-
peratures
dC3-5
Current readings of the three USDA probes.
Current values of the network data points (as configured). Data point 1 (Code
6) is generally the humidity sensor and its value is obtained from the Control-
ler once every minute.
Network Data
Points 1-8
dC6-13
dC14
Cargo Probe 4 Tem-
perature
Current reading of the cargo probe #4.
dC15-19 Future Expansion
These codes are for future expansion, and are not in use at this time.
Current calibration offset values for each of the five probes: supply, return,
USDA #1, #2, and #3. These values are entered via the interrogation pro-
gram.
Temperature Sensors
dC20-24
1-5 Calibration
dC25
Future Expansion
This code is for future expansion, and is not in use at this time..
The DataCORDER serial number consists of eight characters. Function code
dC26 contains the first four characters. Function code dC27 contains the last
four characters. (This serial number is the same as the Controller serial num-
ber)
dC26,27 S/N, Left 4, Right 4
An approximation of the number of logging days remaining until the Data-
CORDER starts to overwrite the existing data.
dC28
dC29
Minimum Days Left
Days Stored
Number of days of data that are currently stored in the DataCORDER.
The date when a Trip Start was initiated by the user. In addition, if the system
goes without power for seven continuous days or longer, a trip start will auto-
matically be generated on the next AC power up.
Date of last Trip
start
dC30
dC31
Shows the current status of the optional battery pack.
PASS: Battery pack is fully charged.
FAIL: Battery pack voltage is low.
Battery Test
dC32
dC33
dC34
Time: Hour, Minute Current time on the real time clock (RTC) in the DataCORDER.
Date: Month, Day
Date: Year
Current date (month and day) on the RTC in the DataCORDER.
Current year on the RTC in the DataCORDER.
Cargo Probe 4
Calibration
Current calibration value for the Cargo Probe. This value is an input via the
interrogation program.
dC35
T-309
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-9 DataCORDER Pre-Trip Res ult Records
DATA
Tes t
No.
TITLE
1-0
1-1
Heater On
Heater Off
Pass/Fail/Skip Result, Change in current for Phase A, B and C
Pass/Fail/Skip Result, Change in currents for Phase A, B and C
Pass/Fail/Skip Result, Water pressure switch (WPS) -- Open/Closed,
Change in currents for Phase A, B and C
2-0
2-1
3-0
Condenser Fan On
Condenser Fan Off
Pass/Fail/Skip Result, Change in currents for Phase A, B and C
Low Speed Evaporator Fan
On
Pass/Fail/Skip Result, Change in currents for Phase A, B and C
Pass/Fail/Skip Result, Change in currents for Phase A, B and C
Pass/Fail/Skip Result, Change in currents for Phase A, B and C
Low Speed Evaporator Fan
On
3-1
4-0
4-1
High Speed Evaporator Fan
On
High Speed Evaporator Fan
On
Pass/Fail/Skip Result, Change in currents for Phase A, B and C
Pass/Fail/Skip Result, STS, RTS, SRS and RRS
5-0
5-1
5-2
6-0
6-1
Supply/Return Probe Test
Secondary Supply Probe Test Pass/Fail/Skip
Secondary Return Probe Test Pass/Fail/Skip
Discharge Thermistor Test
Suction Thermistor Test
Pass/Fail/Skip
Pass/Fail/Skip
Discharge Pressure Sensor
Test
6-2
6-3
6-4
Pass/Fail/Skip
Suction Pressure Sensor Test Pass/Fail/Skip
Compressor Current Draw
Pass/Fail/Skip
Test
6-5
6-6
6-7
Suction Modulation valve Test Pass/Fail/Skip
Economizer Valve Test
Unloader Valve Test
Pass/Fail/Skip
Pass/Fail/Skip
Pass/Fail/Skip Result, AMBS, DPT or CPT (if equipped)
Input values that component opens
7-0
High Pressure Switch Closed
Pass/Fail/Skip Result, STS, DPT or CPT (if equipped)
Input values that component closes
7-1
8-0
8-1
High Pressure Switch Open
Perishable Mode Heat Test
Pass/Fail/Skip Result, STS, time it takes to heat to 16_C (60_F)
Perishable Mode Pull Down
Test
Pass/Fail/Skip Result, STS, time it takes to pull down to 0_C (32_F)
Perishable Mode Maintain
Test
Pass/Fail/Skip Result, Averaged DataCORDER supply temperature
(SRS) over last recording interval.
8-2
9-0
Pass/Fail/Skip Result, DTS reading at end of test, line voltage, line
frequency, time in defrost.
Defrost Test
10-0 Frozen Mode Heat Test
Pass/Fail/Skip Result, STS, time unit is in heat.
10-1 Frozen Mode Pull Down Test Pass/Fail/Skip Result, STS, time to pull down unit to --17.8_C (0_F).
Pass/Fail/Skip Result, Averaged DataCORDER return temperature
10-2 Frozen Mode Maintain Test
(RRS) over last recording interval.
T-309
3-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-10 DataCORDER Alarm Indications
To Acces s : Pres s ALT. MODE key
DESCRIPTION
Code No.
TITLE
The supply recorder sensor reading is outside of the range of --50_C to
70_C (--58_F to +158_F) or, the probe check logic has determined there is
a fault with this sensor.
Recorder Supply
Temperature Out of
Range
dAL70
NOTE
The P5 Pre-Trip test must be run to inactivate the alarm.
The return recorder sensor reading is outside of the range of --50_C to
70_C (--58_F to +158_F) or, the probe check logic has determined there is
a fault with this sensor.
Recorder Return Tem-
perature Out of Range
dAL71
NOTE
The P5 Pre-Trip test must be run to inactivate the alarm.
USDA Temperatures The USDA probe temperature reading is sensed outside of --50 to 70°C
1, 2, 3 Out of Range (--58 to 158°F) range.
dAL72-74
dAL75
Cargo Probe 4 Out of The cargo probe temperature reading is outside of --50 to 70°C (--58 to
Range
158°F) range.
dAL76, 77 Future Expansion
These alarms are for future expansion, and are not in use at this time.
The network data point is outside of its specified range. The DataCORD-
ER is configured by default to record the supply and return recorder sen-
sors. The DataCORDER may be configured to record up to 8 additional
network data points. An alarm number (AL78 to AL85) is assigned to
each configured point. When an alarm occurs, the DataCORDER must be
interrogated to identify the data point assigned. When a humidity sensor is
installed, it is usually assigned to AL78.
Network Data Point
dAL78-85
1 -- 8 Out of Range
The Real Time Clock (RTC) backup battery is too low to adequately
maintain the RTC reading.
dAL86
dAL87
RTC Battery Low
RTC Failure
An invalid date or time has been detected. This situation may be corrected
by changing the Real Time Clock (RTC) to a valid value using the Data-
View.
DataCORDER
dAL88
dAL89
A write of critical DataCORDER information to the EEPROM has failed.
EEPROM Failure
An error has been detected in the process of writing daily data to the non-
volatile FLASH memory.
Flash Memory Error
dAL90
dAL91
Future Expansion
Alarm List Full
This alarm is for future expansion, and is not in use at this time.
The DataCORDER alarm queue is determined to be full (eight alarms).
T-309
3-27
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4
OPERATION
4.1 INSPECTION (Before Starting)
4.3 ADJ UST FRESH AIR MAKEUP VENT
WARNING
The purpose of the fresh air makeup vent is to provide
ventilation for commodities that require fresh air
circulation. The vent must be closed when transporting
frozen foods.
Beware of unannounced starting of the
evaporator and condenser fans. The unit
may cycle the fans and compressor unex-
pectedly as control requirements dictate.
Air exchange depends on static pressure differential,
which will vary depending on the container and howthe
container is loaded.
a. If container is empty, check inside for the following:
1. Check channels or “T” bar floor for cleanliness.
Channels must be free of debris for proper air cir-
culation.
4.3.1 Upper Fres h Air Makeup Vent
2. Check containerpanels, insulation and door seals for
damage. Effect permanent or temporary repairs.
Two slots and a stop are designed into the disc for air
flow adjustments. The first slot allows for a 0 to 30% air
flow, and the second slot allows for a 30 to 100% air
flow. To adjust the percentage of air flow, loosen the
wing nut and rotate the disc until the desired percentage
of air flow matches with the arrow. Tighten the wing
nut. To clear the gap between the slots, loosen the wing
nut until the disc clears the stop. Figure 4-1 gives air
exchange values for an empty container. Higher values
can be expected for a fully loaded container.
3. Visually check evaporator fan motor mounting bolts
for proper securement (refer to paragraph 6.17).
4. Check for dirt or grease on evaporator fan or fan deck
and clean if necessary.
5. Check evaporator coil for cleanliness or obstruc-
tions. Wash with fresh water.
6. Check defrost drain pans and drain lines for obstruc-
tions and clear if necessary. Wash with fresh water.
7. Check panels on refrigeration unit forlooseboltsand
condition of panels. Make sure T.I.R. devices are in
place on access panels.
69NT FRESH AIR MAKEUP
ZERO EXTERNAL STATIC 50HZ
For 60HZ operation multiply curves by 1.2
b. Check condenser coil for cleanliness. Wash with
fresh water.
AIR
FLOW
(CMH)
240
210
180
150
120
90
c. Open control box door. Check for loose electrical
connections or hardware.
T-BAR
1-!/2”
d. Check color of moisture-liquid indicator.
e. Check oil level in compressor sight glass.
T-BAR
2-%/8”
4.2 CONNECT POWER
T-BAR
3”
WARNING
Do not attempt to remove power plug(s) be-
fore turning OFF start-stop switch (ST),
unit circuit breaker(s) and external power
source.
WARNING
60
Makesurethepower plugs areclean and dry
before connecting to any power receptacle.
30
4.2.1 Connection To 380/460 vac Power
0
0
1. Make sure start-stop switch (ST, on control panel)
and circuit breaker (CB-1, in the control box) are in
position “0” (OFF).
10 20 30 40 50 60 70 80 90 100
PERCENT OPEN
2. Plug the 460 vac (yellow) cable into a de-energized
380/460 vac, 3-phase power source. Energize the
power source. Place circuit breaker (CB-1) in posi-
tion “I” (ON). Close and secure control box door.
Figure 4-1 Make Up Air Flow Chart
T-309
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 CONNECT REMOTE MONITORING
RECEPTACLE
1. Depress the ALT MODE key and scroll to Code
dC30.
If remote monitoring is required, connect remote
monitor plug at unit receptacle. (See item 9, Figure 2-5.)
When the remote monitor plug is connected to the
remote monitoring receptacle, the following remote
circuits are energized:
2. Depress and hold the ENTER key for five seconds.
3. The “Trip Start” event will be entered in the Data-
CORDER.
4.6.3 Complete Ins pection
Allow unit to run for 5 minutes to stabilize conditions
and perform a pre--trip diagnosis in accordance with the
following paragraph.
CIRCUIT
FUNCTION
Sockets B to A Energizes remote cool light
Sockets C to A Energizes remote defrost light
Sockets D to A Energizes remote in-range light
4.7 PRE-TRIP DIAGNOSIS
CAUTION
4.5 STARTING AND STOPPING INSTRUCTIONS
Pre-trip inspection should not be performed
with critical temperature cargoes in the con-
tainer.
WARNING
Make sure that the unit circuit breaker(s)
(CB-1 & CB-2) and the START-STOP
switch (ST)arein the“O” (OFF)position be-
fore connecting to any electrical power
source.
CAUTION
When Pre-Trip key is pressed, economy, de-
humidification and bulb mode will be deac-
tivated. At the completion of Pre-Trip activi-
ty, economy, dehumidification and bulb
mode must be reactivated.
4.5.1 Starting the Unit
1. With power properly applied, the fresh air damper set
and (if required) the water cooled condenser con-
nected, (refer to paragraphs 4.2 & 4.3) place the
START-STOP switch to “I” (ON).
Pre-Trip diagnosis provides automatic testing of the
unit components using internal measurements and
comparison logic. The program will provide a “PASS”
or “FAIL” display to indicate test results.
NOTE
The testing begins with access to a pre-trip selection
menu. The user may have the option of selecting one of
two automatic tests. These tests will automatically
perform a series of individual pre--trip tests. The user
may also scroll down to select any of the individual
tests. When only the short sequence is configured it will
appear as “AUtO” in the display, otherwise “AUtO1”
will indicate the short sequence and “AUtO2” will
indicate the long sequence. The test short sequence will
run tests P0 through P6. The long test sequence will run
tests P0 through P10.
Within the first 30 seconds the electronic phase
detection system will check for proper com-
pressor rotation. If rotation is not correct, the
compressor will be stopped and restarted in the
opposite direction. If the compressor is produc-
ing unusually loud and continuous noise after
the first 30 seconds of operation, stop the unit
and investigate.
2. Continue with Start Up Inspection, paragraph 4.6.
A detailed description of the pre-trip test codes is listed
in Table 3-7, page 3-21. If no selection is made, the
pre-trip menu selection process will terminate
automatically. However, dehumidification and bulb
mode must be reactivated manually if required.
4.5.2 Stopping the Unit
To stop the unit, place the START-STOP switch in
position “0” (OFF).
4.6 START--UP INSPECTION
Scrolling down to the “rSLts” code and pressing
ENTER will allow the user to scroll through the results
ofthelast pre--trip testing run. If no pre--testing has been
run (or an individual test has not been run) since the unit
was powered up “--------” will be displayed.
4.6.1 Phys ical Ins pection
a. Check rotation of condenser and evaporator fans.
b. Check compressor oil level. (Refer to paragraph 6.9.)
4.6.2 Check Controller Function Codes
To start a pre--trip test, do the following:
Check and, if required, reset controller Function Codes
(Cd27 through Cd39) in accordance with desired
operating parameters. Refer to paragraph 3.2.2.
NOTE
1. Prior to startingtests, verifythat unit voltage
(Function Code Cd 07) is within tolerance
and unit amperage draw (Function Codes
Cd04, Cd05, Cd06) are within expected
limits. Otherwise, tests may fail incorrectly.
DataCORDER
a. Check and, if required, set the DataCORDER Con-
figuration in accordance with desired recording pa-
rameter. Refer to paragraph 3.6.3.
b. Enter a “Trip Start”. To enter a “trip Start”, do the
following:
2. All alarms must be rectified and cleared
before starting tests.
T-309
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Pre-trip may also be initiated via
communications. The operation is the same
as for the key pad initiation described below
except that should a test fail, the pre-trip
mode will automatically terminate. When
initiated via communications, a test may not
be interrupted with an arrow key, but the
pre-trip mode can be terminated with the
PRE-TRIP key.
the three minute time period expires, the unit will
terminate pre-trip and return to control mode opera-
tion.
2. While the tests are being executed, the user may ter-
minate the pre-trip diagnostics by pressing and hold-
ing the PRE-TRIP key. The unit will then resume
normal operation. If the user decides to terminate a
test but remain at the test selection menu, the user
may press the UP ARROW key. When this is done
all test outputs will be de-energized and the test
selection menu will be displayed.
a. Press the PRE-TRIP key. This accesses a test selec-
tion menu.
3. Throughout the duration of any pre-trip test except
the P-7 high pressure switch tests, the current and
pressure limiting processes are active .
b. TO RUN AN AUTOMATIC TEST: Scroll through
the selections by pressing the UP ARROW or
DOWN ARROW keys to display AUTO, AUTO 1 or
AUTO 2 as desired and then press the AUTO key.
d. Pre-Trip Test Results
At the end of the pre-trip test selection menu, the
message “P,” “rSLts” (pre--trip results) will be
displayed. Pressing the ENTER key will allow the user
to see the results for all subtests (i.e., 1-0, 1-1, etc). The
results will bedisplayed as “PASS”or “FAIL”for all the
tests run to completion since power up. If a test has not
been run since power up, “-- -- -- -- -- ” will be displayed.
Once all pre--test activity is completed,
dehumidification and bulb mode must be reactivated
manually if required.
1. The unit will execute the series of tests without any
need for direct user interface. These tests vary in
length, depending on the component under test.
2. While tests arerunning, “P#-#”will appearon theleft
display, where the #’s indicate the test number and
sub-test. The right display will show a countdown
time in minutes and seconds, indicating how much
time there is left remaining in the test.
CAUTION
4.8 OBSERVE UNIT OPERATION
4.8.1 Probe Check
When a failure occurs during automatic
testing the unit will suspend operation
awaiting operator intervention.
IftheDataCORDER is off orin alarm the controllerwill
revert to a four probe configuration which includes the
DataCORDER supply and return air probes as the
secondary controller probes. The controller
continuously performs probe diagnosis testing which
compares the four probes. If the probe diagnosis result
indicates a probe problem exists, the controller will
perform a probe check to identify the probe(s) in error.
When an automatic test fails, it will berepeated once.
A repeated test failure will cause “FAIL” to be shown
on the right display, with the corresponding test num-
ber to the left. The user may then press the DOWN
ARROWto repeat thetest, theUP ARROWto skip to
the next test or the PRE--TRIP key to terminate test-
ing. The unit will wait indefinitely, until the user
manually enters a command.
a. Probe Diagnostic Logic -- Standard
If the probe check option (controller configuration code
CnF31) is configured for standard, the criteria used for
comparison between theprimary and secondarycontrol
probes is:
CAUTION
When Pre--Trip test Auto 2 runs to comple-
tion without being interrupted, the unit will
terminate pre-trip and display “Auto 2”
“end.” The unit will suspend operation until
the user depresses the ENTER key!
1_C (1.8_F) for perishable set points or 2_C (3.6_F)
for frozen set points.
If25 ormore of30 readings taken within a 30 minute
period are outside of the limit, then a defrost is initi-
ated and a probe check is performed.
When an Auto 1 runs to completion without a failure,
the unit will exit the pre-trip mode, and return to nor-
mal control operation. However, dehumidification
and bulb mode must be reactivated manually if re-
quired.
In this configuration, a probe check will be run as a part
of every normal (time initiated) defrost.
b. Probe Diagnostic Logic -- Special
c. TO RUN AN INDIVIDUAL TEST: Scroll through
the selections by pressing the UP ARROW or
DOWN ARROW keys to display an individual test
code. Pressing ENTER when the desired test code is
displayed.
If the probe check option is configured for special the
abovecriteriaareapplicable. Adefrost with probecheck
will be initiated if 25 of 30 readings or 10 consecutive
readings are outside of the limits
In this configuration, a probe check will not be run as a
part of a normal defrost, but only as a part of a defrost
initiated due to a diagnostic reading outside of the
limits.
c.The30 minutetimerwill be reset at each of the follow-
ing conditions:
1. Individually selected tests, other than the LED/Dis-
play test, will perform the operations necessary to
verify the operation of the component. At the con-
clusion, PASS or FAIL will be displayed. This mes-
sage will remain displayed for up to three minutes,
during which time a user may select another test. If
T-309
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. At every power up.
Any probe(s) determined to be outside the limits will
cause the appropriate alarm code(s) to be displayed to
identify which probe(s) needs to be replaced. The P5
Pre-Trip test must be run to inactivate alarms.
2. At the end of every defrost.
3. After every diagnostic check that does not fall out-
side of the limits as outlined above.
4.9 SEQUENCE OF OPERATION
d. Probe Check
General operation sequences for cooling, heating and
defrost are provided in the following subparagraphs.
Schematic representation of controller action are
provided in Figure 4-2 and Figure 4-3. Refer to Section 3
for detailed descriptions of special events and timers
that are incorporated by the controller in specific modes
of operation.
A defrost cycle probe check is accomplished by
energizing just the evaporator motors for eight minutes
at the end of the normal defrost. At the end of the eight
minute period the probes will be compared to a set of
predetermined limits. The defrost indicator will remain
on throughout this period.
RISING
TEMPERATURE
PULL DOWN
FALLING
TEMPERATURE
+2.5_C
(4.5_F)
+2.5_C
(4.5_F)
START UNLOADED,
TRANSITION TO
ECONOMIZED
OPERATION
MODULATED
COOLING
UNLOADED
MODULATED
COOLING
UNLOADED
+.20_C
SET POINT
--0.20_C
+.20_C
SET POINT
AIR CIRCULATION
UNLOADED OPERATION
AIR CIRCULATION
--0.20_C
AIR CIRCULATION
HEATING
-- 0 . 5 _C
(0.9_F)
-- 0 . 5 _C
(0.9_F)
HEATING
HEATING
NOTE: TEMPERATURES INDICATIONS ARE ABOVE OR BELOW SET POINT
Figure 4-2 Controller Operation -- Peris hable Mode
T-309
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
FALLING
TEMPERATURE
RISING
TEMPERATURE
START UNLOADED,
TRANSITION TO
ECONOMIZED
OPERATION
COOLING
ECONOMIZED
+.20_C
SET POINT
--0.20_C
AIR CIRCULATION
AIR CIRCULATION
NOTE: TEMPERATURES INDICATIONS ARE ABOVE OR BELOW SET POINT
Figure 4-3 Controller Operation -- Frozen Mode
ENERGIZED
DE--ENERGIZED
will switch operation from compressor contactor PB to
compressor contactor PA. Compressor contactors PA is
wired to run the compressor on L1, L2, and L3.
Compressor contactor PB is wired to run the
compressor on L2, L1 and L3 thus providing reverse
rotation .
CONTROL TRANSFORMER
FOR FULL DIAGRAM AND
LEGEND, SEE SECTION 7
POWER TO
CONTROLLER
4.9.2 Sequence Of Operation -- Peris hable Mode
Cooling
PB
T6
PA
PA
T6
PB
TD
NOTE
In the Conventional Perishable Mode of opera-
tion the evaporator motors run in high speed. In
the Economy Perishable Mode the fan speed is
varied.
SIGNAL TO
CONTROLLER
a. With supply air temperature above set point and de-
creasing, the unit will be cooling with the condenser
fan motor (CF), compressor motor (PA or PB), evap-
orator fan motors (EF) energized and the COOL light
illuminated. (See Figure 4-4.) Also, if current or
pressure limiting is not active, the controller will en-
ergize relay TS to open the economizer solenoid
valve (ESV) and place the unit in economized opera-
tion.
TU
USV
TS
ESV
NOTE: HIGH SPEED EVAPORATOR FAN SHOWN. FOR LOW SPEED
CONTACT TE IS DE--ENERGIZED AND CONTACT TV IS ENERGIZED
Figure 4-4 Peris hable Mode
b. When the air temperature decreases to a predeter-
mined tolerance above set point, the in-range light is
illuminated.
4.9.1 Sequence Of operation -- Compres s or Phas e
Sequence
The controller logic will check for proper compressor
rotation. If the compressor is rotating in the wrong
direction, the controller will energize or de--energize
relay T6 as required (see Figure 4-4). Energizing relay
T6 will switch operation from compressor contactor PA
to compressor contactor PB. De--energizing relay T6
c. As the air temperature continues to fall, modulating
cooling starts at approximately 2.5_C (4.5_F) above
set point. (See Figure 4-2.) At set point, relay TS is
de--energized to close the economizer solenoid valve
and relay TU is energized to open the unolader sole-
T-309
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
noid valve changing from economized operation to
unloaded operation. (As shown in Figure 4-5)
rator fans continue to run to circulate air throughout
the container.
c. A safety heater termination thermostat (HTT), at-
tached to an evaporator coil support, will open the
heating circuit if overheating occurs.
d. The controller monitors the supply air. Once the sup-
ply airfalls belowset point the controllerperiodically
records thesupply airtemperature, set point and time.
A calculation is then performed to determine temper-
ature drift from set point over time.
4.9.4 Sequence Of operation -- Frozen Mode Cool-
ing
e. If the calculation determines cooling is no longer re-
quired, contacts TDand TNareopened tode-energize
compressor motor and condenser fan motor. The cool
light is also de-energized.
a. With supply air temperature above set point and de-
creasing, the unit will transition to economized cool-
ing with the condenser fan motor (CF), compressor
motor (CH), economizer solenoid valve (ESV), low
speed evaporator fan motors (ES) energized and the
COOL light illuminated. (See Figure 4-6.)
f. Theevaporatorfan motors continueto run tocirculate
air throughout the container. The in-range light re-
mains illuminated as long as the supply air is within
tolerance of set point.
b.When the air temperature decreases to a predeter-
mined tolerance above set point, the in-range light is
illuminated.
g. If the supply air temperature increases to 0.2_C
(0.4_F) above set point and the three minute off time
has elapsed, relays TD, TU and TN are energized to
restart the compressor and condenser fan motors in
unloaded operation. The cool light is also illumi-
nated.
ENERGIZED
DE--ENERGIZED
CONTROL TRANSFORMER
FOR FULL DIAGRAM AND
LEGEND, SEE SECTION 7
POWER TO
CONTROLLER
ENERGIZED
DE--ENERGIZED
CONTROL TRANSFORMER
FOR FULL DIAGRAM AND
PB
T6
PA
LEGEND, SEE SECTION 7
PA
T6
PB
TD
POWER TO
CONTROLLER
PB
T6
PA
PA
T6
PB
TD
SIGNAL TO
CONTROLLER
TU
USV
TS
ESV
Figure 4-6 Frozen Mode
SIGNAL TO
CONTROLLER
TU
USV
c. When the return air temperature decreases to 0.2_C
(0.4_F) below set point, contacts TD, TS and TN are
opened to de-energize the compressor, economizer
solenoid valve and condenser fan motors. The cool
light is also de-energized.
TS
ESV
NOTE: HIGH SPEED EVAPORATOR FAN SHOWN. FOR LOW SPEED
CONTACT TE IS DE--ENERGIZED AND CONTACT TV IS ENERGIZED
d. The evaporator fan motors continue to run in low
speed to circulate air throughout the container. The
in-range light remains illuminated as long as the re-
turn air is within tolerance of set point.
Figure 4-5 Peris hable Mode Heating
4.9.3 Sequence Of Operation --
Peris hable Mode Heating
e. When return air temperature is 10_C (18_F) or more
below set point, the evaporator fans are brought to
high speed.
a. If the air temperature decreases 0.5_C (0.9_F) below
set point, the system enters the heating mode. (See
Figure 4-2). The controller closes contacts TH (see
Figure 4-5) to allow power flow through the heat ter-
mination thermostat (HTT) to energize the heaters
(HR). TheHEATlight is alsoilluminated. Theevapo-
rator fans continue to run to circulate air throughout
the container.
f. When the return air temperature increases to 0.2_C
(0.4_F) above set point and the three minute off time
has elapsed, relays TD, TS and TN are energizes to
restart the compressor and condenserfan motors. The
cool light is illuminated.
4.9.5 Sequence Of Operation -- Defros t
b. When the temperature rises to 0.2_C (0.4_F) above
set point, contact TH opens to de--energize the heat-
ers. The HEAT light is also de--energized. The evapo-
The defrost cycle may consist of up to three distinct
operations. The first is de-icing of the coil, the second is
a probe check cycle and the third is snap freeze.
T-309
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Defrost may be initiated by any one of the following
methods:
If the controller is programmed with the Lower DTT
setting option the defrost termination thermostat set
point may beconfigured to the default of 25.6_C (78_F)
orlowered to 18_C (64_F). When arequestfor defrostis
made by use of the manual defrost switch,
communications or probe check the unit will enter
defrost if the defrost temperature thermostat reading is
at or below the defrost termination thermostat setting.
Defrost will terminate with the defrost temperature
sensor reading rises above the defrost termination
thermostat setting. When a request for defrost is made
by the defrost intermale timer or by demand defrost, the
defrost temperature setting setting must be below 10_C
(50_F).
1. The manual defrost switch (MDS) is closed by the
user.
2. The user sends a defrost command by communica-
tions.
3. The defrost interval timer (controller function code
Cd27) reaches the defrost interval set by the user.
4. The controller probe diagnostic logic determines
that a probe check is necessary based on the tempera-
ture values currently reported by the supply and re-
turn probes.
5. If the controller is programmed with the Demand
Defrost option (Future) and the option is set to “IN”
the unit will enter defrost if it has been in operation
for over 2.5 hours without reaching set point.
When the defrost mode is initiated the controller opens
contacts TD, TN and TE (or TV) to de-energize the
compressor, condenser fan and evaporator fans. The
COOL light is also de--energized.
ENERGIZED
The controller then closes TH to supply power to the
heaters. The defrost light is illuminated.
DE--ENERGIZED
CONTROL TRANSFORMER
FOR FULL DIAGRAM AND
LEGEND, SEE SECTION 7
When the defrost temperature sensor reading rises to the
defrost termination thermostat setting, the de--icing
operation is terminated.
POWER TO
CONTROLLER
If defrost does not terminate correctly and temperature
reaches the set point of the heat termination thermostat
(HTT) the thermostat will open to de--energize the
heaters. If termination does not occur within 2.0 hours,
the controller will terminate defrost. An alarm will be
given of a possible DTS failure.
PB
T6
PA
PA
TD
T6
PB
If probe check (controller function code CnF31) is
configured to special, the unit will proceed to the next
operation (snap freeze or terminate defrost). If the code
is configured to standard, the unit will perform a probe
check. The purpose of the probe check is to detect
malfunctions or drift in the sensed temperature that is
too small to be detected by the normal sensor out of
range tests. The system will run for eight minutes in this
condition. At the end of the eight minutes, probe alarms
will be set or cleared based on the conditions seen.
SIGNAL TO
CONTROLLER
TU
USV
TS
ESV
Figure 4-7 Defros t
Defrost may be initiated any time the defrost
temperature sensor reading falls below the controller
defrost termination thermostat set point. Defrost will
terminate when the defrost temperature sensor reading
rises above the defrost termination thermostat set point.
The defrost termination thermostat is not a physical
component. It is a controller setting that acts as a
thermostat, “closing” (allowing defrost) when the
defrost temperature sensor reading is below the set point
and “opening”(terminating orpreventing defrost)when
the sensor temperature reading is above set point. When
the unit is operating in bulb mode (refer to paragraph
3.3.9), special settings may be applicable.
When the return air falls to 7_C (45_F), the controller
checks to ensure the defrost temperature sensor (DTS)
reading has dropped to 10_C or below. If it has not, a
DTS failure alarm is given and the defrost mode is
operated by the return temperature sensor (RTS).
If controller function code CnF33 is configured to snap
freeze, the controller will sequence to this operation.
The snap freeze consists of running the compressor
without the evaporator fans in operation for a period of
four minutes with the suction modulation valve fully
open. When the snap freeze is completed, defrost is
formally terminated.
T-309
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5
TROUBLESHOOTING
REMEDY/
REFERENCE
SECTION
CONDITION
POSSIBLE CAUSE
5.1 UNIT WILL NOT START OR STARTS THEN STOPS
External power source OFF
Turn on
Check
Check
Check
Replace
Check
Check
6.17
Start-Stop switch OFF or defective
Circuit breaker tripped or OFF
Circuit breaker OFF or defective
Control transformer defective
Fuse (F3) blown
No power to unit
Loss of control power
Start-Stop switch OFF or defective
Evaporator fan motor internal protector open
Condenser fan motor internal protector open
Compressor internal protector open
High pressure switch open
6.12
6.8
5.7
Component(s) Not Operating
Heat termination thermostat open
Loss of communication with expansion module
Malfunction of current sensor
Low line voltage
Replace
Check Wiring
Replace
Check
Check
6.8
Single phasing
Compressor hums, but does not
start
Shorted or grounded motor windings
Compressor seized
6.8
5.2 UNIT OPERATES LONG OR CONTINUOUSLY IN COOLING
Hot load
Normal
Repair
6.7.1
Container
Defective box insulation or air leak
Shortage of refrigerant
Evaporator coil covered with ice
Evaporator coil plugged with debris
Evaporator fan(s) rotating backwards
Defective evaporator fan motor/capacitor
Air bypass around evaporator coil
Controller set too low
5.6
6.15
6.15/6.17
6.18
Check
Reset
Compressor service valves or liquid line shutoff valve par- Open valves
Refrigeration System
tially closed
completely
Dirty condenser
6.11
Compressor worn
6.8
Current limit (function code Cd32) set to wrong value
Suction modulation valve lost track of step count
Suction modulation valve malfunction
Economizer solenoid valve or TXV malfunction
Unloader valve stuck open
3.5.5
Power cycle
6.20
6.14, 6.19
6.19
T-309
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
REMEDY/
REFERENCE
SECTION
CONDITION
POSSIBLE CAUSE
5.3 UNIT RUNS BUT HAS INSUFFICIENT COOLING
Abnormal pressures
Abnormal temperatures
Abnormal currents
5.7
5.15
5.16
Controller malfunction
5.9
Evaporator fan or motor defective
6.17
Shortage of refrigerant
6.7.1
Power cycle
6.20
Refrigeration System
Suction modulation valve lost track of step count
Suction modulation valve malfunction
Compressor service valves or liquid line shutoff valve par- Open valves
tially closed
completely
6.14, 6.19
6.19
Economizer solenoid valve or TXV malfunction
Unloader valve stuck open
Frost on coil
5.10
5.4 UNIT WILL NOT HEAT OR HAS INSUFFICIENT HEATING
Start-Stop switch OFF or defective
Check
Check
Turn ON
Replace
Replace
6.17
Circuit breaker OFF or defective
External power source OFF
No operation of any kind
Circuit breaker or fuse defective
Control Transformer defective
Evaporator fan internal motor protector open
Heat relay defective
No control power
Check
6.15
Heater termination thermostat open
Heater(s) defective
6.15
Heater contactor or coil defective
Evaporator fan motor(s) defective or rotating backwards
Evaporator fan motor contactor defective
Controller malfunction
Replace
6.15/6.17
Replace
5.9
Unit will not heat or has insuffi-
cient heat
Defective wiring
Replace
Tighten
2.3
Loose terminal connections
Low line voltage
5.5 UNIT WILL NOT TERMINATE HEATING
Controller improperly set
Reset
5.9
Controller malfunction
Unit fails to stop heating
Heater termination thermostat remains closed along with
the heat relay
6.15
5.6 UNIT WILL NOT DEFROST PROPERLY
Defrost timer malfunction (Cd27)
Table 3-5
Tighten/
Replace
Loose terminal connections
Defective wiring
Will not initiate defrost
automatically
Defrost temperature sensor defective or heat termination
thermostat open
Replace
Replace
Heater contactor or coil defective
T-309
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
REMEDY/
REFERENCE
SECTION
CONDITION
POSSIBLE CAUSE
5.6 UNIT WILL NOT DEFROST PROPERLY -- Continued
Manual defrost switch defective
Defrost temperature sensor open
Replace
4.9.5
Will not initiate defrost
manually
Initiates but relay (DR) drops
out
Low line voltage
2.3
Heater contactor or coil defective
Heater(s) burned out
Wet load
Replace
6.15
Initiates but does not defrost
Frequent defrost
Normal
5.7 ABNORMAL PRESSURES (COOLING)
Condenser coil dirty
6.11
6.12
6.12
6.7.1
Open
6.20
Replace
Open
6.13
6.7.1
6.14
6.15
5.6
Condenser fan rotating backwards
Condenser fan inoperative
High discharge pressure
Refrigerant overcharge or noncondensibles
Discharge service valve partially closed
Suction modulation valve malfunction
Faulty suction pressure transducer
Suction service valve partially closed
Filter-drier partially plugged
Low refrigerant charge
Expansion valve defective
Low suction pressure
No evaporator air flow or restricted air flow
Excessive frost on evaporator coil
Evaporator fan(s) rotating backwards
Suction modulation valve malfunction
2.3
6.20
Suction and discharge pressures
tend to equalize when unit is
operating
Compressor operating in reverse
Compressor cycling/stopped
5.14
Check
5.8 ABNORMAL NOISE OR VIBRATIONS
Compressor start up after an extended shutdown
Normal
Brief chattering when manually shut down
Compressor operating in reverse
Loose mounting bolts or worn resilient mounts
Loose upper mounting
5.14
Tighten/Replace
6.8.1 step r.
6.14
Compressor
Liquid slugging
Insufficient oil
6.9
Bent, loose or striking venturi
Worn motor bearings
Check
6.12/6.17
6.12/6.17
Condenser or Evaporator Fan
Bent motor shaft
T-309
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
REMEDY/
REFERENCE
SECTION
CONDITION
POSSIBLE CAUSE
5.9 CONTROLLER MALFUNCTION
Defective Sensor
Defective wiring
Fuse (F1, F2, F3) blown
6.22
Check
Replace
Will not control
Stepper motor suction modulation valve circuit malfunction 6.20
Low refrigerant charge
6.7
5.10 NO EVAPORATOR AIR FLOW OR RESTRICTED AIR FLOW
Frost on coil
5.6
Evaporator coil blocked
Dirty coil
6.15
6.17
6.17
6.17
Replace
Evaporator fan motor internal protector open
Evaporator fan motor(s) defective
No or partial evaporator air flow
Evaporator fan(s) loose or defective
Evaporator fan contactor defective
5.11 THERMOSTATIC EXPANSION VALVE MALFUNCTION
Low refrigerant charge
6.7.1
Open
External equalizer line plugged
Wax, oil or dirt plugging valve or orifice Ice formation at
valve seat
6.14
Low suction pressure with high
superheat
Superheat not correct
6.7.1
Power assembly failure
Loss of element/bulb charge
Broken capillary
6.14
Foreign material in valve
Superheat setting too low
External equalizer line plugged Ice holding valve open
Foreign material in valve
6.14
Open
6.14
High suction pressure with low
superheat
Pin and seat of expansion valve eroded or held open by for-
eign material
Liquid slugging in compressor
Fluctuating suction pressure
6.14
Improper bulb location or installation
Low superheat setting
5.12 AUTOTRANSFORMER MALFUNCTION
Circuit breaker (CB-1 or CB-2) tripped
Power source not turned ON
Check
Check
Unit will not start
5.13 WATER-COOLED CONDENSER OR WATER PRESSURE SWITCH
Water pressure switch malfunction
Check
Check
Condenser fan starts and stops
Water supply interruption
T-309
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
REMEDY/
REFERENCE
SECTION
CONDITION
POSSIBLE CAUSE
5.14 COMPRESSOR OPERATING IN REVERSE
CAUTION
Allowing the scroll compressor to operate in reverse for more than two minutes will result in internal
compressor damage. Turn the start--stop switch OFF immediately.
Incorrect wiring of compressor
Incorrect wiring of compressor contactor(s)
Incorrect wiring of current sensor
Electrical
Check
5.15 ABNORMAL TEMPERATURES
Discharge temperature sensor drifting high
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Failed economizer, TXV or solenoid valve
Plugged economizer, TXV or solenoid valve
Loose or insufficiently clamped sensor
Failed liquid injection solenoid valve
Discharge temperature sensor drifting low
Loose or insufficiently clamped sensor
High discharge temperature
Low suction temperature
5.16 ABNORMAL CURRENTS
Unit reads abnormal currents
Current sensor wiring
Check
T-309
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6
SERVICE
NOTE
To avoid damage to the earth’s ozone layer, use a refrigerant recovery system whenever removing refrigerant.
When working with refrigerants you must comply with all local government environmental laws. In the
U.S.A., refer to EPA section 608.
WARNING
Never use air for leak testing. It has been de-
5
4
termined that pressurized, mixtures of re-
frigerant and air can undergo combustion
when exposed to an ignition source.
6.1 SECTION LAYOUT
Service procedures are provided herein beginning with
refrigeration system service, then refrigeration system
component service, electrical system service,
temperature recorder service and general service. Refer
to the Table Of Contents to locate specific topics.
3
1
2
VALVE
BACKSEATED
VALVE
FRONTSEATED
(Clockwise)
(Counterclockwise)
1. Line Connection
2. Access Valve
3. Stem Cap
4. Valve stem
5. Compressor Inlet
Connection
6.2 SERVICE VALVES
The compressor suction, compressor discharge,
compressor economizer, oil return and the liquid line
service valves (see Figure 6-1) are provided with a
double seat and an access valve which enable servicing
of the compressor and refrigerant lines. Turning the
valve stem clockwise (all the way forward) will
frontseat the valve to close off the line connection and
open a path to the access valve. Turning the stem
counterclockwise (all the way out) will backseat the
valve to open the line connection and close off the path
to the access valve.
Figure 6-2 Suction Service Valve
DISCHARGE
PRESSURE
GAUGE
SUCTION
PRESSURE
GAUGE
With the valve stem midway between frontseat and
backseat, both of the service valve connections are open
to the access valve path.
B
C
A
OPENED (Backseated )
HAND VALVE
CLOSED (Frontseated)
HAND VALVE
For example, the valve stem is first fully backseated
when connecting amanifold gaugeto measurepressure.
Then, the valve is opened 1/4 to 1/2 turn to measure the
pressure.
A. CONNECTION TO LOW SIDE OF SYSTEM
B. CONNECTION TO EITHER:
REFRIGERANT CYLINDER OR
OIL CONTAINER
C. CONNECTION TO HIGH SIDE OF SYSTEM
2
3
1
Figure 6-3 Manifold Gauge Set
6.3. MANIFOLD GAUGE SET
5
4
The manifold gauge set (see Figure 6-3) is used to
determine system operating pressure, add refrigerant
charge, and to equalize or evacuate the system.
VALVE
BACKSEATED
(Counterclockwise)
VALVE
FRONTSEATED
(Clockwise)
When the suction pressure hand valve is frontseated
(turned all the way in), the suction (low) pressure can be
checked. When the discharge pressure hand valve is
frontseated, the discharge (high) pressure can be
checked. When both valves are open (turned
counter-clockwise all the way out), high pressure vapor
will flow into the low side. When the suction pressure
valve is open and the discharge pressure valve shut, the
1. Line Connection
2. Access Valve
3. Stem Cap
4. Valve stem
5. Compressor Or Filter
Drier Inlet Connection
Figure 6-1 Service Valve
T-309
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
system can be charged. Oil can also be added to the
system.
2. Connect the field service coupling (see Figure 6-4)
to the access valve.
3. Turn the field service coupling knob clockwise,
which will open the system to the gauge set.
A R-134a manifold gauge/hose set with self-sealing
hoses (see Figure 6-4) is required for service of the
models covered within this manual. The manifold
gauge/hose set is available from Carrier Transicold.
(Carrier Transicold P/N 07-00294-00, which includes
items 1 through 6, Figure 6-4.)To perform serviceusing
the manifold gage/hose set, do the following:
4. To read system pressures: slightly midseat the ser-
vice valve.
5. Repeat the procedure to connect the other side of the
gauge set.
a. Preparing Manifold Gauge/Hose Set For Use
CAUTION
To prevent trapping liquid refrigerant in the
manifold gauge set be sure set is brought to
suction pressure before disconnecting.
1. Ifthemanifold gauge/hoseset is newor was exposed
to the atmosphere it will need to be evacuated to
remove contaminants and air as follows:
2. Back seat (turn counterclockwise )both field service
couplings (see Figure 6-4) and midseat both hand
valves.
c. Removing the Manifold Gauge Set
1. While the compressor is still ON, backseat the high
side service valve.
3. Connect the yellow hose to a vacuum pump and re-
frigerant 134a cylinder.
2. Midseat both hand valves on the manifold gauge set
and allow the pressure in the manifold gauge set to
bedrawn down to lowsidepressure. This returns any
liquid that may bein thehigh sidehoseto thesystem.
SUCTION
PRESSURE
GAUGE
DISCHARGE
PRESSURE
GAUGE
1
3. Backseat the low side service valve. Backseat both
field service couplings and frontseat both manifold
set valves. Remove the couplings from the access
valves.
CLOSED
OPENED
(Frontseated)
HAND VALVE
(Backseated )
HAND VALVE
4. Install both service valve stem caps and service port
caps (finger-tight only).
To High Side
Access Valve
To Low Side
Access Valve
6.4 PUMPING THE UNIT DOWN
To service the filter-drier, economizer, expansion
valves, moisture-liquid indicator, suction modulation
valve, economizer solenoid valve, unloader solenoid
valve or evaporator coil, pump the refrigerant into the
high side as follows:
3
2
3
BLUE
3
RED
YELLOW
4
CAUTION
5
6
4
Red Knob
Blue Knob
The scroll compressor achieves low suction
pressure very quickly. Do not operate the
compressor in a deep vacuum, internal dam-
age will result.
2
1. Manifold Gauge Set
2. Hose Fitting (0.5-16 Acme)
3. Refrigeration and/or Evacuation Hose
(SAE J2196/R-134a)
4. Hose Fitting w/O-ring (M14 x 1.5)
5. High Side Field Service Coupling
6. Low Side Field Service Coupling
.
a. Attach manifold gauge set to the compressor suction
and discharge service valves. Refer to paragraph 6.3.
b. Start the unit and run in the frozen mode (controller
set below --10°C) for 10 to 15 minutes.
Figure 6-4 R-134a Manifold Gauge/Hos e Set
c. Check function code Cd21 (refer to paragraph 3.2.2).
The economizer solenoid valve should be open. If
not, continue to run until the valve opens.
7. Evacuate to 10 inches of vacuum and then charge
with R-134a to a slightly positive pressure of 0.1 kg/
cm@ (1.0 psig).
d. Frontseat the oil return service valve then, frontseat
theliquid lineservicevalve. Placestart-stop switch in
the OFF position when the suction reaches a positive
pressure of 0.1 kg/cm@ (1.0 psig).
8. Front seat both manifold gauge set valves and dis-
connect from cylinder. The gauge set is now ready
for use.
b. Connecting Manifold Gauge/Hose Set
e. Frontseat the economizer service valve and then
frontseat the suction and discharge service valves.
The refrigerant will be trapped between the compres-
sor suction service valve and the liquid line valve.
To connect the manifold gauge/hose set for reading
pressures, do the following:
1. Remove service valve stem cap and check to make
sure it is backseated. Remove access valve cap. (See
Figure 6-1)
f. Before opening up any part of the system, a slight
positive pressure should be indicated on the pressure
T-309
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
6.6 EVACUATION AND DEHYDRATION
6.6.1 General
gauge. If a vacuum is indicated, emit refrigerant by
cracking theliquid linevalvemomentarilyto buildup
a slight positive pressure.
Moisture is the deadly enemy of refrigeration systems.
The presence of moisture in a refrigeration system can
have many undesirable effects. The most common are
copper plating, acid sludge formation, “freezing-up” of
metering devices by free water, and formation of acids,
resulting in metal corrosion.
g. When opening up the refrigerant system, certain parts
may frost. Allow the part to warm to ambient temper-
ature before dismantling. This avoids internal con-
densation which puts moisture in the system.
h. After repairs have been made, be sure to perform a
refrigerant leak check (refer to paragraph 6.5), and
evacuate and dehydrate the low side (refer to para-
graph 6.6).
6.6.2 Preparation
a. Evacuate and dehydrate only after pressure leak test.
(Refer to paragraph 6.5.)
b. Essential tools to properly evacuate and dehydrate
any system include a vacuum pump (8 m3/hr = 5 cfm
volume displacement) and an electronic vacuum
gauge. (The pump is available from Carrier Trans-
icold, P/N 07-00176-11.)
i. Check refrigerant charge (refer to paragraph 6.7).
6.5 REFRIGERANT LEAK CHECKING
WARNING
c. If possible, keep the ambient temperature above
15.6_C (60_F) to speed evaporation of moisture. If
the ambient temperature is lower than 15.6_C
(60_F), ice might form before moisture removal is
complete. Heat lamps oralternatesourcesofheatmay
be used to raise the system temperature.
Never use air for leak testing. It has been
determined that pressurized, air-rich mix-
tures of refrigerants and air can undergo
combustion when exposed to an ignition
source.
d. Additional time may be saved during a complete sys-
tem pump down by replaceing the filter-drier with a
section of copper tubing and the appropriate fittings.
Installation of a new drier may be performed during
the charging procedure.
a. The recommended procedure for finding leaks in a
system is with aR-134aelectronicleak detector. Test-
ing joints with soapsuds is satisfactory only for locat-
ing large leaks.
3
2
b. If the system is without refrigerant, charge thesystem
with refrigerant 134a to build up pressure between
2.1 to 3.5 kg/cm@ (30 to 50 psig). To ensure complete
pressurization of the system, refrigerant should be
charged at the compressor suction and economizer
service valves and the liquid line service valve. Also,
the area between the suction modulating valve and
evaporator expansion valve may not be open to these
charging points. Pressure between these components
may be checked at the low side access valve (item 11,
Figure 2-2) or by checking that the suction modulat-
ing valve is more than 10% open at controller func-
tion code Cd01. The suction modulating valve may
beopened by useofthecontrollerfunction codeCd41
valve override control (refer to paragraph 6.19). Re-
move refrigerant cylinder and leak-check all connec-
tions.
1
4
5
6
D
S
11
9
7
10
8
NOTE
Only refrigerant 134a should be used to pres-
surize the system. Any other gas or vapor will
contaminate the system, which will require
additional purging and evacuation of the sys-
tem.
1. Liquid Service Valve
2. Receiver or Water
Cooled Condenser
3. Compressor
4. Discharge Service
Valve
6. Suction Service Valve
7. Vacuum Pump
8. Electronic Vacuum
Gauge
9. Manifold Gauge Set
10. Refrigerant Cylinder
5. Economizer Service 11. Reclaimer
Valve
c. If required, remove refrigerant using a refrigerant
recovery system and repair any leaks.
d. Evacuate and dehydrate the unit. (Refer to paragraph
6.6.)
Figure 6-5. Refrigeration Sys tem Service
Connections
e. Charge unit per paragraph 6.7.
6.6.3 Procedure - Complete s ys tem
T-309
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
a. Remove all refrigerant using a refrigerant recovery
system.
1
3
2
b. The recommended method to evacuate and dehydrate
the system is to connect evacuation hoses at the com-
pressor suction, compressor economizer and liquid
line service valve (see Figure 6-5). Be sure the ser-
vice hoses are suited for evacuation purposes.
4
c. The area between the suction modulating valve and
evaporator expansion valve may not be open to the
access valves. To ensure evacuation of this area,
check that the suction modulating valve is more than
10% open at controller function code Cd01. If re-
quired, the suction modulating valve may be opened
by use of the controller function code Cd41 valve
override control. If power is not available to open the
valve, the area may be evacuated by connecting an
additional hose at the low side access valve (item 11,
Figure 2-2).
10
5
8
S
D
9
6
7
d. Test the evacuation setup for leaks by backseating the
unit service valves and drawing a deep vacuum with
thevacuum pump and gaugevalves open. Shut offthe
pump and check to see if the vacuum holds. Repair
leaks if necessary.
1. Receiver or Water
Cooled Condenser
2. Compressor
3. Discharge Service
Valve
5. Suction Service Valve
6. Vacuum Pump
7. Electronic Vacuum
Gauge
8. Manifold Gauge Set
9. Refrigerant Cylinder
10. Reclaimer
e. Midseat the refrigerant system service valves.
f. Open thevacuum pump and electronic vacuum gauge
valves, if they are not already open. Start the vacuum
pump. Evacuate unit until the electronic vacuum
gauge indicates 2000 microns. Close the electronic
vacuum gauge and vacuum pump valves. Shut offthe
vacuum pump. Wait a few minutes to be sure the vac-
uum holds.
4. Economizer Service
Valve
Figure 6-6. Compres s or Service Connections
6.6.4 Procedure - Partial Sys tem
a. If the refrigerant charge has been removed from the
compressor for service, evacuate only the compressor
by connecting the evacuation set--up at the compres-
sor service valves. (See Figure 6-6.) Follow evacua-
tion procedures of the preceding paragraph except
leave compressor service valves frontseated until
evacuation is completed.
g. Break the vacuum with clean dry refrigerant 134a
gas. Raise system pressure to approximately 0.2 kg/
cm@ (2 psig), monitoring it with the compound
gauge.
h. Remove refrigerant using a refrigerant recovery sys-
tem.
b. If refrigerant charge has been removed from the low
side only, evacuate the low side by connecting the
evacuation set--up at the compressor suction and
economizer service valves and the liquid service
valve except leave the service valves frontseated until
evacuation is completed.
i. Repeat steps f.and g. one time.
j. Remove the copper tubing and change thefilter-drier.
Evacuate unit to 500 microns. Close the electronic
vacuum gauge and vacuum pump valves. Shut offthe
vacuum pump. Wait five minutes to see if vacuum
holds. This procedure checks for residual moisture
and/or leaks.
c. Once evacuation has been completed and the pump
has been isolated, fully backseat the service valves to
isolate the service connections and then continue
with checking and, if required, adding refrigerant in
accordance with normal procedures
k. With a vacuum still in the unit, the refrigerant charge
may be drawn into the system from a refrigerant con-
tainer on weight scales. Continue to paragraph 6.7
T-309
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
6.7 REFRIGERANT CHARGE
e. Start unit in cooling mode. Run approximately 10
minutes and check the refrigerant charge.
6.7.1 Checking the Refrigerant Charge
6.7.3 Adding Refrigerant to Sys tem (Partial
Charge)
a. Examine the unit refrigerant system for any evidence
of leaks. Repair as necessary. (Refer to paragraph
6.5.)
NOTE
To avoid damage to the earth’s ozone layer, use
a refrigerant recovery system whenever remov-
ing refrigerant. When working with refriger-
ants you must comply with all local govern-
ment environmental laws. In the U.S.A., refer
to EPA section 608.
b. Maintain the conditions outlined in paragraph 6.7.1
c. Fully backseat the suction service valve and remove
the service port cap.
d. Connect charging line between suction service valve
port and cylinder of refrigerant R-134a. Open
VAPOR valve.
a. Connect the gauge manifold to the compressor dis-
chargeand suction service valves. For units operating
on a water cooled condenser, change over to air
cooled operation.
e. Partially frontseat (turn clockwise) the suction ser-
vice valve and slowly add charge until the refrigerant
appears at the properlevel . Be careful not to frontseat
the suction valve fully, if the compressor is operated
in a vacuum internal damage may result.
b. Bring the container temperature to approximately
1.7_C (35_F)or --17.8_C (0_F). Then set thecontrol-
ler set point to --25_C (--13_F) to ensure that the suc-
tion modulation valve is fully open. (Position of the
suction modulating valve may be checked at control-
ler function code Cd01.)
6.8 COMPRESSOR -- Model RSH105
WARNING
Make sure power to the unit is OFF and
power plug disconnected before replacing
the compressor.
c. Partially block the condenser coil inlet air. Increase
the area blocked until the compressor discharge pres-
sure is raised to approximately 12 kg/cm@ (175 psig).
WARNING
d. On units equipped with a receiver, the level should be
between the glasses. On units equipped with a water
cooled condenser, the level should be at the center of
the glass. If the refrigerant level is not correct, contin-
ue with thefollowing paragraphs to add or removere-
frigerant as required.
Before disassembly of the compressor make
sure to relieve the internal pressure very
carefully by slightly loosening the couplings
to break the seal.
6.7.2 Adding Refrigerant to Sys tem (Full Charge)
CAUTION
The scroll compressor achieves low suction
pressure very quickly. Do not use the com-
pressor to evacuate the system below zero
psig. Never operate the compressor with the
suction or discharge service valves closed
(frontseated). Internal damage will result
from operating the compressor in a deep
vacuum.
a. Evacuate unit and leave in deep vacuum. (Refer to
paragraph 6.6.)
b. Place cylinder of R-134a on scale and connect charg-
ing line from cylinder to liquid line valve. Purge
charging line at liquid linevalve and then noteweight
of cylinder and refrigerant.
c. Open liquid valve on cylinder. Open liquid line valve
half-way and allow the liquid refrigerant to flow into
the unit until the correct weight ofrefrigerant (referto
paragraph 2.2) has been added as indicated by scales.
6.8.1 Removal and Replacement of Compres s or
NOTE
Service compressor contains a nitrogen charge.
Due to the hygroscopic nature of the oil, time
the compressor is left open to the atmosphere
should be minimized as much as possible.
NOTE
It may be necessary to finish charging unit
through suction service valve in gas form, due
to pressure rise in high side of the system.
(Refer to section paragraph 6.7.3)
a. Procure a replacement compressor kit. A list of items
contained in the compressor kit is provided in
Table 6-1.
d. Backseat manual liquid line valve (to close off gauge
port). Close liquid valve on cylinder.
b. If the compressor is operational, pump the unit down
(refer to paragraph 6.4).
T-309
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1 Compres s or Kit
Component
Compressor
Service Valve Seal
Mylar Washers
Item
1
2
3
4
Qty
1
3
4
2
SST Washer
(Kit Item 10)
Resilient Mount
(Kit Item 6)
Wire Tie
5
6
7
8
Oil Sight Glass Plug
Resilient Mount
Upper Shock Mount Ring
Upper Shock Mount Bushing
Compressor Power Plug O--Ring
1
4
1
1
SST Washer
(Kit Item 10)
Mylar Washer
(Kit Item 3)
9
1
10 SST Washers
8
Mylar Protector
(Retain)
c. If the compressor is not operational, turn the unit
start--stop switch (ST) and unit circuit breaker
(CB--1) OFF. Disconnect power to theunit and front--
seat thedischarge, suction, economizer, and oil return
service valves.
Base Plate
(Retain)
Mylar Protector
(Retain)
Remove all remaining refrigerant from the compres-
sor using a refrigerant recovery system. Connect
hoses to suction, economizer and discharge service
valves ports. Evacuate compressor to 500 microns
(75.9 cm Hg vacuum = 29.9 inches Hg vacuum).
Figure 6-8 Compres s or Lower Mounting
d. Make sure power to the unit is OFF and unit power
plug disconnected. Disconnect the power plug from
the compressor.
g. Replace the upper mounting bracket shock mount
ring and bushing (kit items 7and 8). Reassemble the
bracket in the same manner as the original and torque
the shoulder bolt to 2.8 mkg (20 ft--lbs.).
e. Loosen and break the seal at fittings from the suction,
discharge, economizer, and the oil return service
valves. Remove fittings and discard service valve
seals, retain oil return valve O--ring.
h. Remove the male coupling from the top of the sight
glass on the old compressor and hand assemble to the
oil return valve coupling for safe keeping. Plug the
top of the replacement compressor sight glass with
the plug (kit item 5) to prevent spilling oil.
f. Remove the entire compressor upper mounting
bracket assembly,(see Figure 6-7) by removing the
fourcap screws attaching it to theunit and the32--mm
bolt from the compressor mounting bracket.
i. Remove the lower mounting bolts and hardware (see
Figure 6-8). Using plugs from replacement compres-
sor, plug connections on old compressor. Removethe
old compressor. Refer to paragraph 2.2for compres-
sor weight. Return plugs to replacement compressor.
j. The replacement compressor is shipped with an oil
charge of 591ml (20 ounces). Before sliding the new
compressorin theunit, removetheoil sight glassplug
and (using a small funnel) charge the compressor
with an additional 1893ml (64 ounces) Castrol--Ice-
maticSW20 (POEoil). Reassembletheoil sightglass
plug to avoid spilling oil when sliding thecompressor
in the unit.
Upper Shock Mount
Upper Shock Mount
Bushing(Kit Item 8)
Ring (Kit Item 7)
32mm Bolt
k. Secure the base plate and mylar protectors to the com-
pressor with wire ties (kit item 4), and place the com-
pressor in the unit.
Shoulder Bolt
l. Cut and remove the wire ties that were used to hold
the base plate and protectors to the compressor. Us-
ing new resilient mounts, SST washers and mylar
washers (kit items 3, 6 & 10). Install the four mount-
ing screws loosely.
m.Install themalecoupling (removed in step h.) into the
sight glass port.
Figure 6-7 Compres s or Upper Mounting
T-309
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
n. Place the new service seals (kit item 2) at the com-
pressor service ports, connect the four service valves
loosely.
5 Turn Start/Stop switch off and allow oil to drain into
compressor sump. Oil level must be visible in the
sight glass. Ifit is not visible, oil must beadded tothe
compressor.
o. Torquethe fourresilient mount screws to 6.2 mkg (45
ft--lbs).
b. Adding Oil with Compres s or in Sys tem
1. The recommended method is to add oil using an oil
pump at the oil return service valve (see item 15,
Figure 2-3)
p. Torque the four service valves to:
Service Valve
Torque
Suction or Discharge
11 to 13.8 mkg
(80 to 100 ft--lbs.)
2. In an emergency where an oil pump is not available,
oil may bedrawn into the compressorthrough theoil
return service valve.
Economizer
Oil Return
6.9 to 8.3 mkg
(50 to 60 ft--lbs.)
1.4 to 1.66 mkg
(10 to 12 ft--lbs.)
Connect the suction connection of the gauge man-
ifold to the compressor oil return valve port, and
immerse the common connection of the gauge man-
ifold in an open container of refrigeration oil.
Extreme care must be taken to ensure the manifold
common connection remains immersed in oil at all
times. Otherwise air and moisture will be drawn into
the compressor. Crack the oil return service valve
and gaugevalveto vent asmall amount ofrefrigerant
through the common connection and the oil to purge
the lines of air. Close the gauge manifold valve.
q. Reassemble the top mounting bracket (see
Figure 6-7) by hand tightening the 32--mm (1¼
--inch) bolt and torquing the four mounting screws to
0.9 mkg (6.5 ft--lbs). Align the mounting so that the
ring and bushing assembly are free with no compres-
sion.
r. Torque the 32mm bolt to 1.5 mkg (11 ft--lbs.). While
maintaining the free movement of the shock mount,
torque the four mounting screws to 0.9 mkg (6.5 ft--
lbs.).
With the unit running, turn the suction service valve
toward frontseat and induce a vacuum in the com-
pressor crankcase. Do not allow the compressor to
pull below 127mm/hg (5 “/hg). SLOWLY crack the
suction gauge manifold valve and oil will flow
through theoil return servicevalveinto thecompres-
sor. Add oil as necessary.
s. Replace the power plug O--Ring with new ring (kit
item 9). Insert the power plug into the compressor fit-
ting. Be sure plug is fully seated into the fitting and
then thread the coupling nut a minimum of 5 turns.
t. Leak check and evacuate the compressor to 1000 mi-
3 Run unit for 20 minutes in cooling mode. Check oil
level at the compressor sight glass.
crons. Refer to paragraphs 6.5 and 6.6
u. Run the unit for at least 15 minutes and check the oil
and refrigerant levels. Refer to paragraphs 6.7 and
6.9.
c. Removing Oil from the Compres s or:
1 If the oil level is above the sight glass, oil must be
removed from the compressor.
2 Perform a compressor pump down, refer to section
6.4.
6.9 COMPRESSOR OIL LEVEL
3 Removetheoil plug, and drain oil until alevel can be
seen in the sight glass.
CAUTION
Use only Carrier Transicold approved
Polyol Ester Oil (POE) -- Mobil ST32 com-
pressor oil with R-134a. Buy in quantities of
onequart or smaller. When using this hygro-
scopic oil, immediately reseal. Do not leave
container of oil open or contamination will
occur.
4 Run unit for 20 minutes in cooling mode. Check oil
level at the compressor sight glass.
6.10 HIGH PRESSURE SWITCH
6.10.1 Replacing High Pres s ure Switch
a. Turn unit start-stop switch OFF. Frontseat the suc-
tion, discharge, economizer and oil return service
valves to isolate compressor. Remove the refrigerant
from the compressor.
a. Checking the Oil Level in the Compres s or
1 Ideally, ambient temperature should be between
40_F and 100_F.
b. Disconnect wiring from defective switch. The high
pressure switch is located on the discharge service
valve and is removed by turning counterclockwise.
(See Figure 2-3.)
2 Operate the unit in cooling mode for at least 20 min-
utes.
3 Check the controller function code Cd1 for the suc-
tion modulation valve (SMV) position. It should be
at least 20% open.
c. Install a new high pressure switch after verifying
switch settings. (Refer to paragraph 6.10.2.)
4 Locate the oil sight glass on the side of the compres-
sor (item 7, Figure 2-3).
d. Evacuate and dehydrate the compressor per para-
graph 6.6.
T-309
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6.10.2 Checking High Pres s ure Switch
c. Unsolder discharge line and remove the line to the
receiver or water-cooled condenser.
WARNING
d. Remove coil mounting hardware and remove the
coil.
Do not use a nitrogen cylinder without a
pressure regulator. Do not use oxygen in or
near a refrigeration system as an explosion
may occur.
e. Install replacement coil and solder connections.
f. Leak-check the coil connections per paragraph para-
graph 6.5. Evacuate the unit per paragraph 6.6 then
charge the unit with refrigerant per paragraph 6.7.
NOTE
The high pressure switch is non-adjustable.
6.12 CONDENSER FAN AND MOTOR ASSEMBLY
a. Remove switch as outlined in paragraph 6.10.1
WARNING
Do not open condenser fan grille before
turning power OFF and disconnecting
power plug.
b. Connect ohmmeter or continuity light across switch
terminals. Ohm meter will indicate no resistance or
continuity light will be illuminated if the switch
closed after relieving compressor pressure.
The condenser fan rotates counter-clockwise (viewed
from front of unit), pulls air through the the condenser
coil, and discharges horizontally through thefront ofthe
unit. To replace motor assembly:
c. Connect hose to a cylinder of dry nitrogen. (See
Figure 6-9.)
1
4
a. Open condenser fan screen guard.
1. Cylinder Valve
b. Loosen two square head set screws on fan. (Thread
sealer has been applied to set screws at installation.)
Disconnect wiring from motor junction box.
and Gauge
5
2
3
2. Pressure Regulator
3. Nitrogen Cylinder
4. Pressure Gauge
(0 to 36 kg/cm@ =
0 to 400 psig)
CAUTION
Take necessary steps (place plywood over
coil or use sling on motor) to prevent motor
from falling into condenser coil.
6
5. Bleed-Off Valve
6. 1/4 inch Connection
c. Remove motor mounting hardware and replace the
motor. It is recommended that new locknuts be used
when replacing motor. Connect wiring per wiring
diagram.
Figure 6-9 High Pres s ure Switch Tes ting
d. Set nitrogen pressure regulator at 26.4 kg/cm@ (375
psig) with bleed-off valve closed.
d. Install fan loosely on motor shaft (hub side in). DO
NOTUSEFORCE. If necessary, tap thehub only, not
the hub nuts or bolts. Install venturi. Apply “Loctite
H” to fan set screws. Adjust fan within venturi so that
the outer edge of the fan is within 2.0 ± .07 mm
(0.08” ¦ 0.03”) from the outside of the orifice open-
ing. Spin fan by hand to check clearance.
e. Close valve on cylinder and open bleed-off valve.
f. Open cylinder valve. Slowly close bleed-off valve to
increase pressure on switch. The switch should open
at a static pressure up to 25 kg/cm@ (350 psig). If a
light is used, light will go out. If an ohmmeter is used,
the meter will indicate open circuit.
e. Close and secure condenser fan screen guard.
g. Slowly open bleed-off valve to decrease the pressure.
The switch should close at 18 kg/cm@ (250 psig).
f. Apply power to unit and check fan rotation. If fan
motor rotates backward, reverse wire numbers 5 and
8.
6.11 CONDENSER COIL
The condenser consists of a series of parallel copper
tubes expanded into copper fins. The condenser coil
must becleaned with fresh water orsteam so the airflow
is not restricted. To replace the coil, do the following:
6.13 FILTER-DRIER
On units equipped with a water-cooled condenser, if the
sight glass appears to be flashing or bubbles are
constantly moving through the sight glass when the
suction modulation valve is fully open, the unit may
have a low refrigerant charge or the filter-drier could be
partially plugged.
WARNING
Do not open the condenser fan grille before
turning power OFF and disconnecting
power plug.
a. To Check Filter-Drier
1. Test for a restricted or plugged filter-drier by feeling
the liquid line inlet and outlet connections of the
drier cartridge. If the outlet side feels cooler than the
inlet side, then the filter-drier should be changed.
a. Using a refrigerant reclaim system, remove the
refrigerant charge.
b. Remove the condenser coil guard.
T-309
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Check the moisture-liquid indicator if the indicator
shows ahigh level ofmoisture, thefilter-driershould
be replaced.
a. Open the heater access panel (see Figure 2-1) to ex-
pose the evaporator expansion valve.
b. Attach a temperature sensor near the expansion valve
bulb and insulate. Make sure the suction line is clean
and that firm contact is made with the sensor.
b. To Replace Filter-Drier
1. Pump down the unit (refer to paragraph 6.4 and
replace filter-drier.
c. Connect an accurate gauge to the service port directly
upstream of the suction modulating valve.
2. Evacuate the low side in accordance with paragraph
6.6.
d. Set the temperature set point to --18_C (0_F), and run
unit until conditions stabilize.
3. Afterunit is in operation, inspect formoisture in sys-
tem and check charge.
e. The readings may cycle from a high to a low reading.
Take readings of temperature and pressure every
three to five minutes for a total of 5or 6 readings
6.14 EXPANSION VALVES
f. From the temperature/pressure chart (Table 6-7), de-
termine the saturation temperature corresponding to
the evaporator outlet test pressures at the suction
modulation valve.
Two expansion valves are used, the evaporator
expansion valve (item 9, Figure 2-2), and the
economizer expansion valve (item 26, Figure 2-4) .The
expansion valves are automatic devices which maintain
constant superheat of the refrigerant gas leaving at the
point of bulb attachment regardless of suction pressure.
g. Subtract the saturation temperatures determined in
step f. from the temperatures measured in step e.. The
difference is the superheat of the suction gas. Deter-
mine the average superheat It should be 4.5 to 6.7 °C
(8 to 12 °F)
The valve functions are:
1. Automatic control of the refrigerant flow to match
the load.
6.14.2 Valve Replacement
2. Prevention of liquid refrigerant entering the com-
pressor.
a. Removing the Expansion Valve
Unless the valve is defective, it seldom requires
maintenance other than periodic inspection to ensure
that thethermal bulb is tightly secured tothesuctionline
and wrapped with insulating compound. (See
Figure 6-10.)
NOTES
1. The TXV’s are hermetic valves and do not
have adjustable superheat.
2. All connections on the evaporator TXV are
bi---metallic, copper on the inside and
stainless on the outside. When brazing,
bi---metallic connections heat up very
quickly.
3
2
4
1
6
1. Suction Line
2. TXV Bulb Clamp
3. Nut and Bolt
4. TXV Bulb
1
2
3
5
Figure 6-10 Thermostatic Expansion Valve Bulb
6.14.1 Checking Superheat.
4
1. Evaporator Expansion Valve
2. Non-adjustable Superheat Stem
3. Equalizer Connection
4. Inlet Connection
NOTE
Proper superheat measurement for the evapora-
tor expansion valve should be completed at
-- 1 8 _C (0_F) container box temperature where
possible. If the economizer valve is suspect, it
should be replaced.
5. Outlet Connection
6. Expansion Valve Bulb
Figure 6-11 Evaporator Expans ion Valve
T-309
6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Braze Rod
(’Sil-Phos” = 5.5% Silver, 6% Phosphorus)
Copper Tube
(Apply heat for
10-15 seconds)
Bi-metallic Tube Connection
(Apply heat for 2-5 seconds)
Use of a wet cloth is not neces-
sary due to rapid heat dissipation
of the bi--metallic connections
Figure 6-12 Hermetic Thermostatic Expans ion Valve Brazing Procedure
7. If applicable, braze the equalizer connection to the
equalizer line.
8. Check superheat (refer to step 6.14.1).
6.15 EVAPORATOR COIL AND HEATER
ASSEMBLY
INLET
The evaporator section, including the coil, should be
cleaned regularly. The preferred cleaning fluid is fresh
waterorsteam. Anotherrecommended cleaneris Oakite
202 or similar, following manufacturer’s instructions.
OUTLET
The two drain pan hoses are routed behind the
condenser fan motor and compressor. The drain pan
line(s) must be open to ensure adequate drainage.
Figure 6-13 Economizer Expans ion Valve
6.15.1 Evaporator Coil Replacement
1. Pump down the unit per paragraph 6.4.
a. Pump unit down. (Refer to paragraph 6.4.)
2. Removecushion clamps located on theinlet and out-
let lines.
b. With power OFF and power plug removed, remove
the screws securing the panel covering the evaporator
section (upper panel).
3. Unbraze the equalizer connection (if applicable), the
outlet connection and then the inlet connection.
c. Disconnect the defrost heater wiring.
d. Disconnect the defrost temperature sensor (see Fig-
ure Figure 2-2 from the coil. .
4. Remove insulation (Presstite) from expansion valve
bulb.
e. Remove middle coil support.
5. Unstrap thebulb, located belowthecenterof thesuc-
tion line (4 o’clock position), and remove the valve.
f. Remove the mounting hardware from the coil.
g. Unsolder the two coil connections, one at the distrib-
utor and the other at the coil header.
b. Installing the Expansion Valve
1. Clean the suction line with sandpaper before instal-
ling bulb to ensure proper heat transfer. Apply ther-
mal grease to the indentation in the suction line.
h. After defective coil is removed from unit, remove
defrost heaters and install on replacement coil.
i. Install coil assembly by reversing above steps.
2. Strap the thermal bulb to the suction line, making
sure bulb is placed firmly into the suction line. See
Figure 6-10 for bulb placement.
j. Leak check connections per paragraph 6.5. Evacuate
the unit per paragraph 6.6 and add refrigerant charge
per paragraph 6.7.
3. Insulate the thermal bulb.
6.15.2 Evaporator Heater Replacement
a.Beforeservicing unit, makesuretheunit circuit break-
ers (CB-1 & CB-2) and the start-stop switch (ST) are
in theOFF position, and that thepowerplug andcable
are disconnected.
4. The economizer expansion valves should be
wrapped in a soaked cloth for brazing. See
Figure 6-12. Braze inlet connection to inlet line
5. Braze outlet connection to outlet line.
b. Remove the lower access panel (Figure 2-1) by
removing the T.I.R. locking device lockwire and
mounting screws.
6. Reinstall the cushion clamps on inlet and outlet
lines.
T-309
6-10
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Determine which heater(s) need replacing by check-
ing resistance on each heater. Refer to paragraph 2.3
for heater resistance values
2 Be sure electrical power is removed from the unit.
Disconnect leads. Remove top screw and washer.
Lift off coil. (See Figure 6-14 or Figure 6-15)
3 Unbraze valve from unit and braze new valve in
place
d. Remove hold-down clamp securing heaters to coil.
e. Lift the bent end of the heater (with the opposite end
down and away from coil). Move heater to the side
enough to clear the heater end support and remove.
4 Install coil. Evacuate low side and place unit back
in operation. Check charge.
1
2
6.16 ECONOMIZER, UNLOADER, LIQUID INJ EC-
TION AND OIL RETURN SOLENOID VALVE
3
4
a. Replacing the Coil
NOTE
The coil may be replaced without removing the
refrigerant.
5
6
7
1 Be sure electrical power is removed from the unit.
Disconnect leads. Remove top screw and washer.
Lift off coil. (See Figure 6-14 or Figure 6-15)
8
9
2 Verify coil type, voltage and frequency of old and
new coil. This information appears on the coil hous-
ing.
b. Replacing Valve Internal Parts (Unloader
Solenoid Only)
1 Pump down the unit. Refer to paragraph 6.4.
1. Top Screw
2. Washer
3. Coil
6. Gasket
2 Be sure electrical power is removed from the unit.
Disconnect leads. Remove top screw and washer.
Lift off coil. (See Figure 6-14)
7. Stem and Plunger
8. Seat Disc
9. Body
4. Locknut
5. Enclosing Tube
3 Remove the top screw (see Figure 6-14), washer ,
and coil assembly.
Figure 6-14. Unloader Solenoid Valve
4 Loosen the enclosing tube locknut.
1
5 Remove enclosing tube and locknut assembly. The
gasket is inside the enclosing tube.
2
3
6 Remove seat disc from inside of body and check for
obstructions and foreign material.
7 Placetheseat discinto thevalvebodywith thesmall-
er diameter end facing up.
4
8 Install stem and plunger.
9 Place the enclosing tube locknut over the enclosing
tube. Install spacer over enclosing tube making sure
it is seated properly in the enclosing tube locknut.
Tighten enclosing tube locknut to a torque value of
2.78 mkg (20 ft-lb). Do not overtighten.
1. Slotted Screw
2. Washer
3. Coil
4. Enclosing Tube and
Body
10 Install coil assembly, washer and top screw.
11 Evacuateand dehydratethesystem. (Referto section
6.6.) Charge unit with refrigerant per section 6.7.
Figure 6-15. Oil Return Solenoid Valve (ORV),
Economizer Solenoid Valve (ESV), Liquid
Injection Solenoid Valve (LIV)
12 Start unit and check operation.
c. Replacing Valve
6.17 EVAPORATOR FAN AND MOTOR ASSEMBLY
1 To replace the unloader, liquid injection or econo-
mizervalve, pump down the unit. Refer to paragraph
6.4. To replace the oil return valve, remove the re-
frigerant charge.
The evaporator fans circulate air throughout the
container by pulling air in the top of the unit. The air is
forced through the evaporator coil where it is either
heated or cooled and then discharged out the bottom of
T-309
6-11
Download from Www.Somanuals.com. All Manuals Search And Download.
6.18 EVAPORATOR FAN MOTOR CAPACITORS
the refrigeration unit into the container. The fan motor
bearings are factory lubricated and do not require
additional grease.
The evaporator fan motors are of the permanent-split
capacitor type. The motor is equipped with one
capacitor used in the high speed circuit and another
capacitor used for the low speed circuit.
6.17.1 Replacing The Evaporator Fan As s embly
WARNING
6.18.1 When To Check For A Defective Capacitor
Always turn OFF the unit circuit breakers
(CB-1 & CB-2) and disconnect main power
supply before working on moving parts.
a. Fan motor will not change speed. For example: in the
conventional perishable mode, the motors should run
in high speed. In the economy perishable mode they
should switch speeds and in the frozen mode, the mo-
tors should run in low speed.
a. Remove upper access panel (see Figure 2-2) by
removing mounting bolts and T.I.R. locking device.
Reach inside of unit and remove the Ty-Rap securing
the wire harness loop. Then unplug the connector by
twisting to unlock and pulling to separate. NOTE: It
may be easier to unplug the connector with the motor
assembly partially pulled out (after step b).
NOTE
The evaporator fan motors will always start in
high speed.
b. Motor running in wrong direction (after checking
for correct wiring application).
b. Remove the four mounting bolts that secure the mo-
tor--fan assembly to the unit.
c. Motor will not start, and IP-EM’s are not open.
c. Slide the fan assembly out from the unit and place it
on a sturdy work surface.
6.18.2 Removing The Capacitor
WARNING
d. Remove the motor and fan from the assembly.
e. Replace the motor.
Make sure power to the unit is OFF and
power plug disconnected before removing
capacitor(s).
f. Lubricate the fan motor shaft with a graphite--oil
solution (Never--Seez) and apply thread sealer (Loc-
tite H, brown in color) to the two fan set screws.
Install fan on themotorshaft, so that the coupling sur-
face will be even with the end of the motor shaft.
The capacitors are located on the motor and above the
evaporator fan deck they may be removed by two
methods:
1 If container is empty, open upper rear panel of the
unit. The capacitor may be serviced after disconnect-
ing power plug.
g. Install the fan assembly in reverse order of removal.
Apply power momentarily to check for proper fan
rotation (refer to paragraph 2.3). If thefan spins back-
wards, than motor wiring or motor is defective.
2 If container is full, turn the unit power OFF and dis-
connect power plug. Remove the evaporator fan
motor access panel. (See see Figure 2-1). For
removal of the evaporator fan assembly, refer to sec-
tion 6.17.
Replace access panel making sure that panel does not
leak. Lock--wire the T.I.R. locking device(s).
4
WARNING
With power OFF dischargethe capacitor be-
fore disconnecting the circuit wiring.
3
5
2
6
1
8
9
6.18.3 Checking The Capacitor
If the capacitor is suspected of malfunction, you may
choose to simply replace it. Direct replacement requires
a capacitor of the same value. Two methods for
checking capacitor function are:
1. Volt-ohmmeter set on RX 10,000 ohms.
Connect ohmmeter leads across the capacitor terminals
and observe the meter needle. If the capacitor is good,
the needle will make a rapid swing toward zero
resistance and then gradually swing back toward a very
high resistance reading.
7
If the capacitor has failed open, the ohmmeter needle
will not move when the meter probes touch the
terminals. If the capacitor is shorted, the needle will
swing to zero resistance position and stay there.
1. Bracket
6. Cap Screw, Hxhd
5/16-18 x 1.25
7. Fan
8. Shim
9. Evaporator Motor
2. Flat washer, 3/8
3. Bolt, 3/8-16 x 1.00
4. Locknut, 5/16-18
5. Flat washer, 5/16
2. Capacitor analyzer:
The function of the analyzer is to read the microfarad
value of a capacitor and to detect insulation breakdown
Figure 6-16. Evaporator Fan As s embly
T-309
6-12
Download from Www.Somanuals.com. All Manuals Search And Download.
under load conditions. The important advantages of a
analyzer are its ability to locate capacitors that have
failed to hold their microfarad ratings, or those that are
breaking down internally during operation. It is also
useful in identifying capacitors when their microfarad
rating marks have become unreadable.
Right Dis play
CAP
(Capacity Mode)
Available Selections
AUtO
(Normal Control)
UnLd
(Unloader = Open
Economizer = Closed)
6.19 VALVE OVERRIDE CONTROLS
Std
(Unloader = closed
Economizer = closed)
CAUTION
ECOn
DO NOT disassemblepiston from NEW suc-
tion modulating valve powerhead assembly.
Doing so may result in damage to piston.
(Unloader = closed
Economizer = open)
SM
AUtO
(SMV % Setting)
(Normal Control)
Controller function code Cd41 is a configurable code
that allows timed operation of the automatic valves for
troubleshooting. Threetest sequences are provided. The
first, capacity mode (CAP), allows alignment of the
unloader and economizer solenoid valves in the
standard, unloaded and economized operating
configurations. The second, SMV % Setting (SM)
allows opening of the suction modulating valve to
various percentages and the third, Oil Valve Setting
(OIL)and Liquid ValveSetting (LIV)allows opening or
closing of the oil return solenoid valve and the liquid
injection solenoid valve. A fourth selection is also
provided to enter a time period of up to three minutes,
during which the override(s) are active. If the timer is
active, valve override selections will take place
immediately. If the timer is not active, changes will not
take place for a few seconds after the timer is started.
When the timer times out, override function is
automatically terminated and the valves return to
normal machinery control. To operate the override, do
the following:
0
3
4
6
12
25
50
100
AUto
(Normal Control)
CLOSE
OPEn
AUto
(Normal Control)
OIL
(Oil Valve Setting)
LIV
(Liquid Valve Setting, if
applicable)
CLOSE
OPEn
0 00 (0 minutes/0 Seconds)
In 30 second increments to
3 00 (3 minutes/ 0 seconds)
tIM
(Timer)
6.20 SUCTION MODULATION VALVE
a. Press theCODE SELECT key then press anARROW
key until Cd41 is displayed in the left window. The
right window will display a controller communica-
tions code.
On start up of the unit, the valve will reset to a known
open position. This is accomplished by assuming the
valve was fully open, driving it fully closed, resetting
the percentage open to zero, then opening to a known
10% staging position.
b. Press the ENTER key. The left display will show a
test name alternating with the test setting or time re-
maining. Use an ARROW key to scroll to the desired
test. Press the ENTER key and SELCt will appear in
the left display.
FROM COIL
2-1/8 inch Nut
c. Use an ARROW key to scroll to the desired setting,
and then press the ENTER key. Selections available
for each of the tests are provided in the following
table.
d. If the timer is not operating, follow the above proce-
dure to display the timer. Use an ARROW key to
scroll to thedesired timeinterval and press ENTER to
start the timer.
TO COMPRESSOR
FROM UNLOADER
e. The above described sequence may be repeated dur-
ing the timer cycle to change to another override.
Figure 6-17 Suction Modulation Valve (SMV)
T-309
6-13
Download from Www.Somanuals.com. All Manuals Search And Download.
6.20.1 Precheck Procedure
ing to light indicates an open on that leg which indi-
cates a poor connection or an open coil. Repair or re-
place as required to achieve proper operation.
a. Check unit for abnormal operation.
b. Check charge. If refrigerant is low repair as required
and again check operation.
CAUTION
c. If sufficient capacity cannot be maintained or unit is
tripping excessively on high pressure switch (HPS)
in high ambients, check coils and clean if required.
The scroll compressor achieves low suction
pressure very quickly. Do not operate the
compressor in a deep vacuum, internal dam-
age will result.
d. If capacity or control cannot be maintained turn unit
OFF, then back ON. This will reset the valve in the
event the controller lost communication with the
valve, and may correct the problem.
3. Restart unit, set the step rate to 200 PPS on SMA-12
forthevalve, and close steppervalve whilewatching
the suction gauge. Within one minute the suction
pressure will go into a vacuum. This is an indication
that the valve is moving.
NOTE
Carefully listen to the valve. During reset, the
valve will make a ratcheting noise that may be
heard or felt as it is attempting to close. If this
can be heard or felt, it indicates that the control-
ler and drive module are attempting to close the
valve, and may serve as a quick indication that
the drive is in working order.
4. If no change in suction pressure is detected, check
for resistance (refer to step 6.20.2), and check con-
nections for proper continuity and retest. If the valve
is functioning and all connections and motor resist-
ance are good, check the controller and expansion
module.
CAUTION
DO NOT disassemblepiston from NEW suc-
tion modulating valve powerhead assembly.
Doing so may result in damage to piston.
e. Operation of the valve may be checked using the con-
troller valve override program, function code Cd41.
Refer to paragraph 6.19 for valve override test in-
structions.
5. If the valve is determined as faulty after completing
the above steps, perform a low side pump down. Re-
move valve powerhead assembly, and replace with a
NEWvalvepowerhead assembly, torquenut to 35 ft-
lb, evacuate low side, and open all service valves.
6.20.2 Checking The Stepper valve
a. Checking with ohmmeter
Disconnect the four pin connector to the stepper SMV.
With a reliable digital ohmmeter, check the winding
resistance. In normal ambient, the valve should have 72
to 84 ohms measured on the red/green (a-b terminals)
and on the white/black (c-d terminals) leads. If an
infinite or zero reading occurs, check connections and
replace the motor.
6.21 CONTROLLER AND EXPANSION MODULE
6.21.1 Handling Modules
CAUTION
Do not remove wire harnesses from module
unless you are grounded to the unit frame
with a static safe wrist strap.
b. Checking with SMA-12 portable stepper drive tester
The SMA-12 portable stepper drive tester (Carrier
Transicold P/N 07-00375-00) is a battery operated
stepperdrive which will open and closethe SMV, which
allows a more thorough check of the operating
mechanism.
CAUTION
Unplug all module connectors before per-
forming arc welding on any part of the con-
tainer.
To check operation:
1. Stop theunit, disconnect the fourpin connectorfrom
thesteppermoduleto thevalve(seeFigure 6-17)and
attach theSMA-12 stepperdriveto theconnectorgo-
ing to the valve.
The guidelines and cautions provided herein should be
followed when handling the modules. These
precautions and procedures should be implemented
when replacing a module, when doing any arc welding
on the unit, or when service to the refrigeration unit
requires handling and removal of a module.
2. Set the SMA-12 pulse per second (PPS) to one PPS
and either open or close valve. Each LED should
light sequentially until all four are lit. Any LED fail-
T-309
6-14
Download from Www.Somanuals.com. All Manuals Search And Download.
This test point enables the user to check if the controller
unloader solenoid valve relay (TU) is open or closed.
2
1
2
3
TP2
This test point enables the user to check if the high
pressure switch (HPS) is open or closed.
TP3
This test point enables the user to check if the water
pressure switch (WP) contact is open or closed.
TP 4
This test point enables the user to check if the internal
protectorforthecondenserfan motor(IP-CM)is open or
closed.
TP 5
This test point enables the user to check if the internal
protectors for the evaporator fan motors (IP-EM1 or
IP-EM2) are open or closed.
TP 6
This test point is not used in this application.
5
4
TP 7
This test point enables the user to check if the controller
economizer solenoid valve relay (TS) is open or closed
1. Controller Software
Programming Port
2. Mounting Screw
3. Controller
4. Expansion Module
5. Test Points
TP 8
This test point enables the user to check power to the
suction modulator valve.
TP 9
Figure 6-18 Controller Section of the Control Box
This test point is the chassis (unit frame) ground
connection.
a. Obtain a grounding wrist strap (Carrier Transicold
part number 07--00--304--00)and a static dissipation
mat (Carrier Transicold part number 07--00304--00.
The wrist strap, when properly grounded, will dissi-
pate any potential buildup on the body. The dissipa-
tion mat will provide a static-free work surface on
which to place and/or service the modules.
TP 10
This test point enables the user to check if the heat
termination thermostat (HTT) contact is open or closed.
6.21.3 Controller Programming Procedure
To load newsoftwareinto themodule, theprogramming
card is inserted into the programming/software port.
b. Disconnect and secure power to the unit.
c. Place strap on wrist and attach the ground end to any
exposed unpainted metal area on the refrigeration
unit frame (bolts, screws, etc.).
CAUTION
The unit must be OFF whenever a program-
ming card is inserted or removed from the
controller programming port.
d. Carefully removethemodule. Do not touch any ofthe
electrical connections if possible. Place the module
on the static mat.
NOTE
e. The strap should be worn during any service work on
a module, even when it is placed on the mat.
The metal door on the programming card must
be facing to the left when inserting.
6.21.2 Controller Trouble-Shooting
a. Procedure for loading Operational Software
1. Turn unit OFF, via start-stop switch (ST).
Agroup oftest points (TP, seeFigure 6-18)areprovided
on the controller for trouble-shooting electrical circuits
(see schematic diagram, section 7). A description of the
test points follows:
2. Insert the programming card for Operational Soft-
ware into the programming/software port. (See
Figure 6-18)
NOTE
3. Turn unit ON, via start-stop switch (ST).
Use a digital voltmeter to measure ac voltage
between TP’s and ground (TP9), except for
TP8.
4. The Display module will alternate back and forth
between the messages “rEV XXXX” and “Press
EntR”. (If a defective card is being used the Display
will blink the message “bAd CArd”. Turn start-stop
switch OFF and remove the card.)
TP1
T-309
6-15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Press the ENTER key on the keypad.
3 Disconnect theback connectors and removemodule.
4 When removing the replacement module from its
packaging , note how it is packaged. When returning
the old module for service, place it in the packaging
in the same manner as the replacement. The packag-
ing has been designed to protect the module from
both physical and electrostatic discharge damage
during storage and transit.
6. The Display will showthe message“Pro SoFt.”This
message will last for up to one minute.
7. The Display module will read “Pro donE” when the
software loading has loaded. (If a problem occurs
while loading the software: the Display will blink
the message “Pro FAIL” or “bad 12V”. Turn start-
stop switch OFF and remove the card.)
b.Installation:
8. Turn unit OFF, via start-stop switch (ST).
Install the module by reversing the removal steps.
9. Remove the programming card from the program-
ming/software port and return the unit to normal op-
eration by placing the start-stop switch in the ON
position.
Torque values for mounting screws (item 2, see
Figure 6-18) are 0.23 mkg (20 inch-pounds). Torque
value for the connectors is 0.12 mkg (10 inch-pounds).
6.22 TEMPERATURE SENSOR SERVICE
b. Procedure for loading Configuration Software
1. Turn unit OFF using start-stop switch (ST).
Procedures for service of the Return Recorder, Return
Temperature, Supply Recorder, Supply Temperature,
Ambient, Defrost Temperature, Compressor Discharge
and Compressor Suction temperature sensors are
provided in the following sub paragraphs.
2. Insert the programming card, for Configuration
Software, into the programming/software port. (See
Figure 6-18.)
3. Turn unit ON using start-stop switch (ST).
6.22.1 Sens or Checkout Procedure
4. The Display module will show “nt40” on the left
LCD display and “531###” on the right LCD dis-
play. “###” will indicate the dash number for agiven
unit model number, use the UP or DOWN ARROW
key to scroll through the list to obtain the proper
model dash number. For example, to program a
model number 69NT40-531-05, press the UP or
DOWN ARROW key until the right display shows
“nt40” on the right display and “53105” on the left.
(If a defective card is being used, the Display will
blink the message “bAd CArd”. Turn start-stop
switch OFF and remove the card.)
Mounting Stud Type
40 mm (1 1/2 inch)
Sens or
6.3 mm (1/4 inch)
Bulb Type
40 mm (1-1/2 inches )
Sens or
6.3 mm (1/4 inch)
40 mm (1-1/2 inches )
Dual Sens or
5. Press the ENTER key on the keypad.
6. When the software loading has successfully com-
pleted, the Display will show the message “EEPrM
donE.” (If a problem occurs while loading the soft-
ware, theDisplay will blink themessage “Pro FAIL”
or “bad 12V.” Turn start-stop switch OFF and
remove the card.)
6.3 mm (1/4 inch)
Figure 6-19 Sens or Types
To check a sensor reading, do the following:
a. Remove the sensor and place in a 0_C (32_F) ice-wa-
ter bath. The ice-water bath is prepared by filling an
insulated container (of sufficient size to completely
immersebulb)with icecubes or chipped ice, then fill-
ing voids between ice with water and agitating until
mixture reaches 0_C (32_F) measured on a labora-
tory thermometer.
7. Turn unit OFF using start-stop switch (ST).
8. Remove the programming card from the program-
ming/software port and return the unit to normal op-
eration by placing the start-stop switch in the ON
position.
6.21.4 Removing and Ins talling a Module
b. Start unit and check sensor reading on the control
panel. The reading should be 0_C (32_F). If the read-
ing is correct, reinstall sensor; if it is not, continue
with the following.
a. Removal:
1. Disconnect all front wire harness connectors and
move wiring out of way.
c. Turn unit OFF and disconnect power supply.
2 The lower controller mounting is slotted, loosen the
top mounting screw (see Figure 6-18) and lift up and
out.
d. Referto paragraph 6.21 and removecontroller to gain
access to the sensor plugs.
T-309
6-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-2 Sens or Temperature/Res is tance Chart
(+/--.002%)
b. Cut wire(s) 5 cm (2 inches) from shoulder of defec-
tive sensor and discard the defective probe only.
c. Cut one wire of existing cable 40 mm (1-1/2 inch)
shorter than the other wire.
Temperature
Res is tance
(Ohms )
_C
_F
d. Cut one replacement sensor wire (opposite color)
back 40 mm (1-1/2 inch). (See Figure 6-19.)
AMBS,
CPDS
CPSS,
DTS, RTS,
RRS, STS,
SRS
e. Strip back insulation on all wiring 6.3 mm (1/4 inch).
f. Slide a large piece of heat shrink tubing over the
cable, and place the two small pieces of heat shrink
tubing, one over each wire, before adding crimp fit-
tings as shown in Figure 6-20.
-- 3 0
-- 2 5
-- 2 0
-- 1 5
-- 1 0
-- 5
0
-- 2 2
-- 1 3
-- 4
177,000
130,400
97,070
72,900
55,330
43,200
32,650
25,390
19,900
15,700
12,490
10,000
8,060
1,770,000
1,340,000
970,700
729,000
553,000
423,300
326,500
253,900
199,000
157,100
124,900
100,000
80,600
Sens or (Typical)
5
14
Heat Shrink
Tubing (3)
Cable
23
32
5
41
Large Heat Shrink
Tubing (1)
10
15
20
25
30
35
40
45
50
55
60
65
65
50
59
Figure 6-20 Typical Sens or and Cable Splice
68
g. Slip crimp fittings over dressed wires (keeping wire
colors together). Make sure wires are pushed into
crimp fittings as faras possibleand crimp with crimp-
ing tool.
77
86
95
6,530
65,300
104
113
122
131
140
149
158
5,330
53,300
h. Solder spliced wires with a 60% tin and 40% lead
Rosincore solder.
4,370
43,700
i. Slide heat shrink tubing over splice so that ends of
tubing cover both ends of crimp as shown in
Figure 6-20.
3,600
36,000
2,900
29,000
2,490
24,900
j. Heat tubing to shrink oversplice. Makesureallseams
are sealed tightly against the wiring to prevent mois-
ture.
2,080
20,800
1,750
17,500
k. Slide large heat shrink tubing over both splices and
shrink.
e. Using the plug connector marked “EC”, that is con-
nected to the back of the controller, locate the sensor
wires (RRS, RTS, SRS, STS, AMBS, DTS, CPDS
OR CPSS as required). Followthose wires to thecon-
nector and using the pins of the plug, measure the
resistance. Values are provided in Table 6-2.
CAUTION
Do not allow moisture to enter wire splice
area as this may affect the sensor resistance.
l. Position sensor in unit as shown in m.Figure 6-21
Slip crimp fittings over dressed wires (keeping wire
colors together). Make sure wires are pushed into
crimp fittings as far as possible and crimp with
crimping tool. and re--check sensor resistance.
Due to the variations and inaccuracies in ohmmeters,
thermometers or other test equipment, a reading
within 2% of the chart value would indicate a good
sensor. If a sensor is defective, the resistance reading
will usually be much higher or lower than the resis-
tance values given.
n. Reinstall sensor, refer to paragraph 6.22.3.
6.22.2 Sens or Replacement
NOTE
The P5 Pre-Trip test must be run to inactivate
probe alarms (refer to paragraph 4.7).
a. Turn unit power OFF, disconnect power supply and
remove sensor assembly from unit.
T-309
6-17
Download from Www.Somanuals.com. All Manuals Search And Download.
T.I.R. Bolts
Supply
Air
STS probe
SRS probe
Stream
Ins ulation
Back Panel
Supply Sens or
Mounting
Clamp
Sens or
Wires
Gas keted
Cover
Gas ket
Mounting
Plate
Gas keted
Support
Plate
2.5” Drip Loop
Figure 6-21 Supply Sens or Pos itioning
Sens or DTS
6.22.3 Sens or Re --Ins tallation
a. Sens ors STS and SRS
c
The DTS sensor must have insulating material placed
completely over the sensor to insure the coil metal
temperature is sensed.
To properly position a supply sensor, the sensor must be
fully inserted into the probe holder. Do not allow heat
shrink covering to contact the probe holder. For proper
placement of the sensor, be sure to position the enlarged
positioning section of the sensor against the the side of
the mounting clamp. This positioning will give the
sensor the optimum amount of exposure to the supply
air stream, and will allow the Controller to operate
correctly. See Figure 6-21.
6.23 MAINTENANCE OF PAINTED SURFACES
The refrigeration unit is protected by a special paint
system against the corrosive atmosphere in which it
normally operates. However, should thepaint system be
damaged, the base metal can corrode. In order to protect
the refrigeration unit from the highly corrosive sea
atmosphere, or if the protective paint system is
scratched or damaged, clean area to bare metal using a
wire brush, emery paper or equivalent cleaning method.
Immediately following cleaning, apply 2--part epoxy
paint to the area. and allow to dry. After the first coat
dries, apply a second coat.
b
Sens ors RRS and RTS
Reinstall the return sensor as shown in Figure 6-22. For
proper placement of the return sensor, be sure to
position the enlarged positioning section of the sensor
against the the side of the mounting clamp.
6.24 COMPOSITE CONTROL BOX REPAIRS
6.24.1 Introduction
This procedure provides instructions for repair of the
Carrier Transicold composite control box. Damage to
the control box may be in the form of a chip or hole, a
crack, a damaged thread insert or damage to the door
hinge inserts. Generally, the object of the repair must be
to ensure sufficient strength is restored to the damaged
area and the repair must keep the box water tight.
Information on repair kits and repairprocedures foreach
type of damage is provided in the following paragraphs.
Ambient temperature must be above 7°C (45°F) for
proper curing of epoxy repairs.
Mounting
Return Sensor
1.50 in.
(38.1cm)
Clamp
Figure 6-22 Return Sens or Pos itioning
T-309
6-18
Download from Www.Somanuals.com. All Manuals Search And Download.
6.24.2 Cracks
The damaged insert must be removed from the control
box. Table 6-5 identifies the drill size and drill depth to
beused foreach insert. A stop ring should beused on the
drill bit to limit the depth.
Cracks in the control box are repaired using a fiberglass
patch over the damaged area. Materials required are
included in theFiberglass Patch Kitsupplied withCrack
Repair Kit, Carrier Transicold part number
76-00724-00SV (see Table 6-3).
a. Center the drill bit on the insert and drill to the pre-
scribed depth.
a. The surface must be clean and dry. Roughen the sur-
face with sandpaper to ensure a good bond.
b. Remove the chips from the drilled hole.
c. Mix the two component epoxy and fill the hole 1/2
way to the top with epoxy.
b. Cut the fiberglass cloth to allow a 25mm (1--inch)
overlap around the area to be repaired.
d. Press the insert in until it is flush with the surface.
c. Stretch and position the cloth over the area to be re-
paired and secure it with masking tape.
e. Wipe away any excess epoxy. The part is ready for
service after the bond material has hardened and is
tack free (approximately 20 minutes)
d. Make up sufficient epoxy glue to cover the cloth by
mixing equal parts of resin and hardener. Saturate the
cloth with the epoxy glue, spreading evenly.
6.24.5 Door Hinge Ins erts
e. Remove the tape and overlap the edge of the cloth
approximately 6 to 12 mm (1/4” to 1/2”) with glue.
If the door hinges have been pulled from the control box
drill and reinstall the hinge as shown in Figure 6-23 and
described in the following steps.
f. Epoxy will dry in 45--60 minutes. When completely
cured (12 hours), use sandpaper to smooth edges of
the patch.
6.24.3 Chips And Holes
Chips and holes in the control box are repaired using a
piece of aluminum or stainless steel to cover the
damaged area. Thematerial can becut to suit andriveted
in place. An adhesive sealant must be used to make the
repair watertight. The adhesive sealant (Sikaflex 221)is
included in Crack Repair Kit Carrier Transicold part
number 76-00724-00SV (see Table 6-3). Do not use an
acetone based silicone sealant (Which can be
identified by a vinegar--like odor).
a. To make up the patch, cut a piece of aluminum or
stainless steel so that it will overlap the damaged area
by at least 40 mm (1 1/2”) on all sides.
b. Choose rivet locations and drill the rivet holes in the
corresponding locations on the control box and patch
piece.
c. Apply the adhesive sealant around the damaged area
to form a seal between the control box and the patch
piece.
Figure 6-23 Door Hinge Repair
Materials needed:
d. Rivet the patch piece in place.
1. Cut two square pieces of 3 mm thick (1/8 inch) alu-
minum or stainless steel approximately 40 mm (1
5/8”) square. These squares will serve as backing
plates.
e. File smooth any rough edges (including rivets) that
may come into contact with wires.
6.24.4 Ins erts
The threaded brass inserts that are molded into the
control box will need to be replaced if the threads
become stripped, or if the insert becomes loose. The
inserts and epoxy are contained in repair kit, Carrier
Transicold part number 76-50084-00 (see Table 6-4).
There are 6 different inserts used in the control box.
Refer to Figure 6-24 for the locations of the various
inserts.
2. Two nuts, bolts (10 -- 24 x 1”) and washers for each
insert that needs repair.
a. Drill a 1/4” hole in the center of each square backing
plate.
b. Pass the bolts through the bolts holes in the door
hinge, then through the control box at the location
where the hinge insert pulled out.
NOTE
c. From inside the control box, slide the backing plates
over the bolts and secure in place with the washers
and nuts.
An epoxy application gun isalso needed, Carri-
er Transicold part number 07 -- 00391 -- 00.
T-309
6-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-3 Crack, Chip & Hole Repair Kit
DESCRIPTION
ITEM
PART NUMBER
76--00724--00SV
76--00724--00Z
02--00067--02Z
98--02339--00
Qty
1
1
2
3
4
Crack Repair Kit -- Includes
. . . Fiberglass Patch Kit (Loctite FK--98 or 80265)
. . . Sikaflex 221 Adhesive Sealant (Sikaflex 232--361)
. . . Instruction Sheet
10
10
10
Table 6-4 Ins ert Repair Kit
ITEM
1
DESCRIPTION
PART NUMBER
76--50084--00
34--06231--01
34--06231--03
34--06231--04
34--06231--05
34--06231--06
34--06231--07
02--0082--00
07--00390--00
98--02338--00
Qty
1
Insert Repair Kit -- Includes
2
. . . Insert - 17.53 x 9.91 mm (..690 x .390 in) 1/4--20 Threads
. . . Insert - 15.88 x 6.35 mm (.625 x .250 in) 10-24 Threads
. . . Insert - 25.15 x 7.54 mm (.990 x .297 in) 10-24 Threads
. . . Insert - 10.16 x 9.53 mm (.400 x .375 in) 10-24 Threads
. . . Insert - 12.7 x 9.91 mm (.5 x .390 in) 1/4--20 Threads
. . . Insert - 9.53 x 6.76 mm (.375 x .266 in) 10-24 Threads
. . . Durabond Epoxy E20--HP (Loctite 29314)
10
10
10
10
10
10
1
3
4
5
6
7
8
9
. . . Static Mixing Tube (Loctite 983440)
1
10
. . . Instruction Sheet
1
Note: Insert repair procedures require use of an Application Gun, Carrier part number 07--00391--00
Table 6-5 Drill Information
Item
Ins ert part number
34- 06231- 01
34- 06231- 03
34- 06231- 04
34- 06231- 05
34- 06231- 06
34- 06231- 07
Drill s ize and depth
1
2
3
4
5
6
10.3 mm x 17.8 mm deep (.404 in. x .700 in. deep)
6.8 mm x 16.3 mm deep (.266 in. x .640 in. deep)
7.9 mm x 25.4 mm deep (.3125 in. x 1.0 in. deep)
6.9 mm (.270 in.) Drill completely through.
10.3 mm (.404 in.) Drill completely through.
6.8 mm (.266 in.) Drill completely through.
T-309
6-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6-24. Ins ert Location
T-309
6-21
Download from Www.Somanuals.com. All Manuals Search And Download.
6.25 COMMUNICATIONS INTERFACE MODULE
INSTALLATION
c.. Remove the circuit breaker panel, with circuit
breaker, from the control box.
d.. Locate, wires CB21/CIA3, CB22/CIA5 and
CB23/CIA7 that have been tied back in the wire
harness. Remove the protective heat shrink fromthe
ends of the wires.
e.. Attach the three wires as addressed to the LOAD
side of the circuit breaker.
f.. Refit the circuit breaker panel.
g. Fit the new RMU into the unit.
h. Remove plugs CIA, CIB and CID from the wiring
harness and attach to the module.
Communications
interface Module
.i. Replace the low voltage shield.
CB1
Table 6-6 Recommended Bolt Torque Values
Figure 6-25. Communications Interface
Ins tallation
BOLT DIA. THREADS
TORQUE
MKG
FREE SPINNING
Units with communication interface module provision
have the required wiring installed. The provision wiring
kit (part number 76--00685--00), includes three
pre--addressed wires installed between the circuit
breakerand communication interface modulelocations.
These wires are to be connected to the module and
circuit breaker to allow the module to communicate
over the power system. To install the module, do the
following:
#4
#6
40
32
32
24
20
18
16
14
13
12
11
10
5.2 in-lbs
9.6 in-lbs
20 in-lbs
23 in-lbs
75 in-lbs
11 ft-lbs
20 ft-lbs
31 ft-lbs
43 ft-lbs
57 ft-lbs
92 ft-lbs
124 ft-lbs
0.05
0.11
0.23
0.26
0.86
1.52
2.76
4.28
5.94
7.88
12.72
17.14
#8
#10
1/4
5/16
3/8
7/16
1/2
9/16
5/8
3/4
WARNING
The Unit Power Plug Must Be Disconnected
To Remove Power From Circuit Breaker
Cb1
NONFREE SPINNING (LOCKNUTS ETC.)
1/4
5/16
3/8
20
18
16
14
13
12
11
10
82.5 in-lbs
145.2 in-lbs
22.0 ft-lbs
34.1 ft-lbs
47.3 ft-lbs
62.7 ft-lbs
101.2 ft-lbs
136.4 ft-lbs
0.95
1.67
3.04
4.71
6.54
8.67
13.99
18.86
a.. CB1 is connected to the power system, see wiring
schematic. Ensure that the unit power is off AND
that the unit power plug is disconnected.
7/16
1/2
9/16
5/8
b.. Open control box, see Figure 6-25 and remove low
voltage shield. Open high voltage shield.
3/4
T-309
6-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-7 R-134a Temperature - Pres s ure Chart
Temperature
Vacuum
Temperature
Pres s ure
kPa kg/cm@ bar
_F
_C
“/hg cm/hg kg/cm@ bar
_F
28
_C
-- 2
-- 1
0
ps ig
-- 4 0
.35
-- 4 0
.37
14.6
12.3
9.7
49.4
41.6
32.8
22.7
11.9
7.1
37.08
31.25
24.64
17.00
8.89
0.49
0.42
0.33
0.23
0.12
0.07
0.02
24.5 168.9
26.1 180.0
27.8 191.7
29.6 204.1
31.3 215.8
33.2 228.9
35.1 242.0
40.1 276.5
45.5 313.7
51.2 353.0
57.4 395.8
64.1 441.0
71.1 490.2
78.7 542.6
86.7 597.8
95.3 657.1
104.3 719.1
114.0 786.0
124.2 856.4
135.0 930.8
1.72
1.84
1.95
2.08
2.20
2.33
2.47
2.82
3.20
3.60
4.04
4.51
5.00
5.53
6.10
6.70
7.33
8.01
8.73
9.49
1.69
1.80
1.92
2.04
2.16
2.29
2.42
2.76
3.14
3.53
3.96
4.42
4.90
5.43
5.98
6.57
7.19
7.86
8.56
9.31
30
32
-- 3 0
-- 2 5
-- 2 0
-- 1 8
-- 1 6
-- 3 4
-- 3 2
-- 2 9
-- 2 8
-- 2 7
34
1
6.7
36
2
3.5
38
3
2.1
5.33
40
4
0.6
2.0
1.52
45
7
Temperature
Pres s ure
50
10
13
16
18
21
24
27
29
32
35
38
41
43
46
49
52
54
57
60
63
66
68
_F
-- 1 4
-- 1 2
-- 1 0
-- 8
-- 6
-- 4
-- 2
0
_C
-- 2 6
-- 2 4
-- 2 3
-- 2 2
-- 2 1
-- 2 0
-- 1 9
-- 1 8
-- 1 7
-- 1 6
-- 1 4
-- 1 3
-- 1 2
-- 1 1
-- 1 0
-- 9
ps ig
0.4
kPa
1.1
kg/cm@ bar
55
0.03
0.08
0.14
0.20
0.26
0.32
0.39
0.46
0.53
0.60
0.68
0.76
0.84
0.93
1.02
1.11
1.20
1.30
1.40
1.50
1.61
0.03
0.08
0.14
0.20
0.26
0.32
0.39
0.45
0.52
0.59
0.67
0.74
0.83
0.91
1.00
1.09
1.18
1.28
1.37
1.48
1.58
60
1.2
8.3
65
2.0
13.8
20.0
25.5
31.7
36.6
44.8
52.4
59.3
66.9
74.5
82.7
91.0
70
2.9
75
3.7
80
4.6
85
5.6
90
6.5
95
2
7.6
100
105
110
115
120
125
130
135
140
145
150
155
4
8.6
6
9.7
146.4 1009 10.29 10.09
158.4 1092 11.14 10.92
171.2 1180 12.04 11.80
184.6 1273 12.98 12.73
198.7 1370 13.97 13.70
213.6 1473 15.02 14.73
229.2 1580 16.11 15.80
245.6 1693 17.27 16.93
262.9 1813 18.48 18.13
281.1 1938 19.76 19.37
8
10.8
12.0
13.2
10
12
14
16
18
20
22
24
26
14.5 100.0
15.8 108.9
17.1 117.9
18.5 127.6
19.9 137.2
21.4 147.6
22.9 157.9
-- 8
-- 7
-- 6
-- 4
-- 3
T-309
6-23
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7
ELECTRICAL WIRING SCHEMATIC
7.1 INTRODUCTION
This section contains the Electrical Schematics and Wiring Diagrams. The diagrams are presented as follows:
Figure 7-1 Provides the legend for use with all figures.
Figure 7-2 Provides the basic schematic diagram.
Figure 7-3 Provides the basic wiring diagram.
Sequence of operation descriptions for the various modes of operation are provided in paragraph 4.9
LEGEND
SYMBOL
AMBS
C
DESCRIPTION (Schematic Location)
SYMBOL
DESCRIPTION (Schematic Location)
AMBIENT SENSOR (C--21)
ORV
PA
OIL RETURN SOLENOID VALVE (N--24, H-9)
CONTROLLERS (H-21, H-23)
COMPRESSOR PHASE CONTACTOR (L--11,M--10,P1)
COMPRESSOR PHASE CONTACTOR (L--10,M--11,P2)
CB1
CB2
CF
CIRCUIT BREAKER -- 460 VOLT (J --1)
CIRCUIT BREAKER -- AUTOTRANSFORMER (C--1)
CONDENSER FAN CONTACTOR (M--12, N--5)
COMMUNICATIONS INTERFACE MODULE (A--3)
COOL LIGHT (J --7)
PB
PR
PROBE RECEPTACLE [USDA]
D--21,L--22,M--22)
RM
REMOTE MONITORING RECEPTACLE
(J-6,J --7,K--6,K--7,K--8)
CI
CL
RRS
RTS
SMV
SPT
SRS
ST
RETURN RECORDER SENSOR (K--21)
RETURN TEMPERATURE SENSOR (B--21)
SUCTION MODULATING VALVE (K--24)
SUCTION PRESSURE TRANSDUCER (H--21)
SUPPLY RECORDER SENSOR (K--22)
START -- STOP SWITCH (K--4)
CM
CONDENSER FAN MOTOR (H--12, T-5)
COMPRESSOR MOTOR (T--1)
CP
CPDS
CPSS
CR
COMPRESSOR DISCHARGE SENSOR (A--22)
COMPRESSOR SUCTION SENSOR (D--21)
CHART RECORDER [TEMPERATURE RECORDER]
(K-16)
STS
TCC
SUPPLY TEMPERATURE SENSOR (A--21)
CS
CURRENT SENSOR (M--1)
TransFRESH COMMUNICATIONS
CONNECTOR (D-4)
DHBL
DHBR
DHTL
DHTR
DL
DEFROST HEATER -- BOTTOM LEFT (T--4)
DEFROST HEATER -- BOTTOM RIGHT (R--4)
DEFROST HEATER -- TOP LEFT (T--4)
DEFROST HEATER -- TOP RIGHT (R--4)
DEFROST LIGHT (J --6)
TD
TE
CONTROLLER RELAY -- COOLING (H11)
CONTROLLER RELAY -- HIGH
SPEED EVAPORATOR FANS
(K--13)
TFC
TH
TN
TP
TransFRESH CONTROLLER (G--5)
DPT
DTS
DISCHARGE PRESSURE TRANSDUCER (J --22)
DEFROST TEMPERATURE SENSOR (B--22)
DUAL VOLTAGE MODULE (D--1)
CONTROLLER RELAY -- HEATING (K--15)
CONTROLLER RELAY -- CONDENSER FAN (K--12)
DVM
DVR
E1
TEST POINT (F--17,G--12,H--11,J --12,
J --13,J --15,M--19)
DUAL VOLTAGE RECEPTACLE (F--1)
EVAPORATOR FAN CONTACTOR [HIGH]
(L--13,L--14,P--7,P--10)
TR
TRANSFORMER (M--3)
TRANS AUTO TRANSFORMER 230/460 (D--1)
EM
ES
EVAPORATOR FAN MOTOR (E--13,G--13,T--8,T--11)
TRC
TS
TransFRESH REAR CONNECTOR (E--5)
EVAPORATOR FAN CONTACTOR [LOW]
( M -- 1 4 , P -- 7 , P -- 11 )
ECONOMIZER SOLENOID VALVE (K--17)
CONTROLLER RELAY -- ECONOMIZER SOLENOID
VALVE (E--17)
ESV
F
FUSE (C--6,D--20,E--20,H--4)
TT
TU
CONTROLLER RELAY -- COOLING (C--11)
FLA
HPS
HR
HS
FULL LOAD AMPS
CONTROLLER RELAY -- UNLOADER SOLENOID
VALVE (E--16)
HIGH PRESSURE SWITCH (G--11)
HEATER CONTACTOR (L--15, N--3)
HUMIDITY SENSOR (F--21)
TV
CONTROLLER RELAY -- LOW SPEED EVAPORATOR
FANS (K--14)
T1
T2
T4
T6
CONTROLLER RELAY -- RM COOL (G--7)
CONTROLLER RELAY -- RM DEFROST (G--6)
CONTROLLER RELAY -- RM INRANGE (G--8)
HTT
IC
HEAT TERMINATION THERMOSTAT (G--15)
INTERROGATOR CONNECTOR [FRONT/REAR]
(P--22,P--21)
CONTROLLER RELAY -- COMPRESSOR PHASE
SEQUENCING (K--10,K--11)
IP
INTERNAL PROTECTOR (E--13,G--13,H--12)
IN RANGE LIGHT (J8)
IRL
LIV
MDS
USV
WP
UNLOADER SOLENOID VALVE (K--16)
WATER PRESSURE SWITCH (E--12)
LIQUID INJECTION SOLENOID VALVE (K-18)
MANUAL DEFROST SWITCH (E--19)
Figure 7-1 LEGEND
T-309
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7-2 SCHEMATIC DIAGRAM
T-309
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7-3 WIRING DIAGRAM (Sheet 1 of 2)
T-309
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7-3 WIRING DIAGRAM (Sheet 2 of 2)
T-309
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
E
Air Cooled Condenser Section, 2-4
Evacuation, 6-3
Alarm, 3-6, 3-10, 3-12, 3-17, 3-27
Evaporator, 6-10
Evaporator Fan, 6-12
Evaporator Section, 2-2
Expansion Module, 3-1, 6-14
Expansion Valves, 6-10
B
Battery, 1-1
C
F
Capacitors, 6-12
Failure Action, 3-4
Checking Superheat, 6-9
Communications, 1-1
Filter--Drier, 6-8
Communications Interface Module, 3-11, 6-21
Compressor, 1-1, 6-5
Fresh Air Makeup, 2-1, 4-1
Frozen Mode, 4-6
Compressor Phase Sequence, 4-5
Compressor Section, 2-3
Condenser Coil, 1-1, 6-8
Condenser Fan, 6-8
Frozen Mode -- Conventional, 3-6
Frozen Mode -- Economy, 3-6
Function Code, 3-14, 3-25
Configuration Identification, 1-1
Configuration Software, 3-3, 3-8
Configuration Variables, 3-13
Control Box, 1-1, 2-5, 6-18
Controller, 3-3, 6-14
G
General Description, 2-1
Generator Protection, 3-4
Controller Software, 3-3
H
Heat Lockout, 3-4, 3-6
D
Heater, 6-10
DataCORDER, 3-7, 3-10, 4-2
DataCORDER Software, 3-7
DataReader, 3-11
Heating Mode, 4-6
High Pressure Switch, 6-7
DataView, 3-11
I
Defrost Interval, 3-4
Defrost Mode, 4-7
Inspection, 4-1, 4-2
Interrogator, 1-1
Introduction, 1-1
Dehumidification, 1-1
Display Module, 3-2
Index-1
T-309
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Refrigeration Circuit, 2-10
K
Refrigeration System Data, 2-6
Refrigeration Unit -- Front Section, 2-1
Remote Monitoring, 1-1
Key Pad, 3-2
L
Leak Checking, 6-3
S
Logging Interval, 3-10
Safety and Protective Devices, 2-8
Sampling Type, 3-10
Scroll Back , 3-10
M
Manifold Gauge Set, 6-1
Microporcessor System, 3-1
Modes Of Operation, 3-4
Sensor Configuration, 3-8
Sequence Of Operation, 4-5
Service Valves, 6-1
Solenoid Valves, 6-10
Starting, 4-2
O
Stopping, 4-2
Oil, 6-7
Suction Modulating Valve, 6-13
Operational Software, 3-4, 3-7
Option Descriptions, 1-1
T
P
Temperature Control, 3-4, 3-6
Temperature Sensor, 6-17
Thermistor Format, 3-10
Torque Values, 6-21
Painted Surfaces, 6-17
Perishable Mode -- Bulb, 3-5
Perishable Mode -- Conventional, 3-4
Perishable Mode -- Dehumidification, 3-5
Perishable Mode -- Economy, 3-5
Power, 4-1
U
Upper Air, 1-2
Pre--Trip, 3-7, 3-10, 3-21, 3-26, 4-2
Pressure Readout, 1-1
V
Probe Check, 4-3
Valve Override Controls, 6-12
Pumping Down, 6-2
W
R
Refrigerant Charge, 6-4
Wiring Schematic, 7-1
T-309
Index-2
Download from Www.Somanuals.com. All Manuals Search And Download.
|