LTR20091058, Rev. B
6/15/09
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Important Safety Instructions
READ AND FOLLOW ALL INSTRUCTIONS
WARNING:
DANGER -- Risk of injury:
To reduce the risk of injury, do not permit children to The suction fittings in this spa are sized to match
use this product unless they are closely supervised the specific water flow created by the pump. Should
at all times.
the need arise to replace the suction fittings, or the
pump, be sure the flow rates are compatible.
DANGER -- Risk of accidental drowning:
Never operate the spa if the suction fitting or filter
baskets are broken or missing. Never replace a suc-
tion fitting with one that is rated less than the flow
rate marked on the original suction fitting.
Do not allow children to be in or around a spa unless
a responsible adult supervises them. Keep the spa
cover on and locked when not in use. See instructions
enclosed with your cover for locking procedures.
DANGER -- Risk of electric shock:
DANGER -- Risk of electric shock:
Install the spa at least 5 feet (1.5 meters) from all Do not permit any external electrical appliances,
metal surfaces. As an alternative, a spa may be in- such as lights, telephones, radios, televisions, and
stalled within 5 feet of metal surfaces if each metal etc., within five feet (1.5 meters) of the spa. Never
surface is permanently bonded by a minimum #8 attempt to operate any electrical device from inside
AWG solid copper conductor to the outside of the the spa.
spa’s control box.
WARNING -- To reduce the risk of injury:
The use of alcohol, drugs or medication before or
during spa use may lead to unconsciousness, with
the possibility of drowning.
The spa water should never exceed 104˚F (40˚C).
Water temperatures between 100˚F (38˚C) and
104˚F (40˚C) are considered safe for a healthy adult. Persons suffering from obesity, a medical history of
Lower water temperatures are recommended for heart disease, low or high blood pressure, circulatory
young children and when spa use exceeds 10 min- system problems or diabetes should consult a physi-
utes.
cian before using the spa.
High water temperatures have a high potential for Persons using medications should consult a physician
causing fetal damage during pregnancy. Women who before using the spa since some medications may
are pregnant, or who think they are pregnant, should induce drowsiness while others may affect heart rate,
always check with their physician prior to spa usage. blood pressure and circulation.
HYPERTHERMIA DANGER:
Prolonged exposure to hot air or water can induce
hyperthermia. Hyperthermia occurs when the inter-
nal temperature of the body reaches a level 3˚F to
6˚F above the normal body temperature of 98.6˚F
(or 2˚C to 4˚C above 37˚C). While hyperthermia
has many health benefits, it is important not to allow
your body’s core temperature to rise above 103˚F
(39.5˚C).
•
•
Failure to perceive heat
Failure to recognize the need to exit spa or hot
tub
•
•
•
•
Unawareness of impending hazard
Fetal damage in pregnant women
Physical inability to exit the spa
Unconsciousness
Symptoms of excessive hyperthermia include dizzi-
ness, lethargy, drowsiness and fainting. The effects
of excessive hyperthermia may include:
WARNING: The use of alcohol, drugs, or medication
can greatly increase the risk of fatal hyperthermia.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2
DANGER -- Risk of electric shock:
•
•
•
Replace a damaged power cord immediately.
Do not bury the power cord.
Connect to a grounded, grounding-type receptacle only.
WARNING: People with infectious diseases should not use a spa or hot tub.
WARNING: To avoid injury, exercise care when entering or exiting the spa or hot tub.
WARNING: Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconscious-
ness and possible drowning.
WARNING: Do not use a spa or hot tub immediately following strenuous exercise.
WARNING: Prolonged immersion in a spa or hot tub may be injurious to your health.
CAUTION: Maintain water chemistry in accordance with manufacturer’s instructions.
SAVE THESE INSTRUCTIONS
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Preparing for Your New Portable Spa
Most cities and counties require permits for exterior construction and electrical circuits. In addition, some
communities have codes requiring residential barriers such as fencing and/or self-closing gates on property to
prevent unsupervised access to the property by children. Your dealer can provide information on which permits
may be required and how to obtain them prior to the delivery of your spa.
Planning the Best Location
Provide a View with Your Spa
Think about the direction you will be facing when
Safety First
Do not place your spa within 10 feet (3 m) of over-
sitting in your spa. Do you have a special landscaped
head power lines.
area in your yard that you find enjoyable? Perhaps
there is an area that catches a soothing breeze dur-
ing the day or a lovely sunset in the evening.
Consider How You Will Use Your Spa
How you intend to use your spa will help you de-
termine where you should position it. For example,
will you use your spa for recreational or therapeutic
purposes? If your spa is mainly used for family rec-
reation, be sure to leave plenty of room around it for
activity. If you will use it for relaxation and therapy,
you will probably want to create a specific mood
around it.
Keep Your Spa Clean
In planning your spa’s location, consider a location
where the path to and from the house can be kept
clean and free of debris.
Prevent dirt and contaminants from being tracked
into your spa by placing a foot mat at the spa’s en-
trance where the bathers can clean their feet before
entering your spa.
Plan for Your Environment
If you live in a region where it snows in the winter or
rains frequently, place the spa near a house entry. By
doing this, you will have a place to change clothes
and not be uncomfortable.
Allow for Service Access
Many people choose to install a decorative structure
around their spa. If you are installing your spa with
any type of structure on the outside, such as a gaze-
bo, remember to allow access for service. It is always
best to design special installations so that the spa
can still be moved, or lifted off the ground.
Consider Your Privacy
In a cold-weather climate, bare trees won’t provide
much privacy. Think of your spa’s surroundings dur-
ing all seasons to determine your best privacy op-
tions. Consider the view of your neighbors as well
when you plan the location of your spa.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Preparing a Good Foundation
Damage caused by inadequate or improper
foundation support is not covered by the war-
ranty
Place the spa on a level concrete slab not less than
3” / 8 cm thick. If you are installing the spa indoors,
pay close attention to the flooring beneath it. Choose
flooring that will not be damaged or stained.
It is the responsibility of the spa owner to provide a
proper foundation for the spa.
If you are installing your spa on an elevated wood
deck or other structure, consult a structural engineer
or a contractor to ensure the structure will support
the weight of 150 pounds per square foot.
We strongly recommended that you have a qualified,
licensed contractor prepare the foundation for your
spa.
Electrical Installation
This product is a cord-connected spa with a pump heater, lighting fixture, and spa side control. The operating
power is 110V AC.
A licensed electrician may be required to upgrade your standard receptacle and/or circuit breaker. Always
follow applicable local, state and federal codes and guidelines.
The spa is equipped with a 15 amp GFCI cord and Testing the GFCI
plug kit.
Test the GFCI plug prior to first use and periodically
when the spa is powered. To test the GFCI plug ver-
sion, follow these instructions. (Spa should already
be plugged in and operational.)
Plug the spa into a dedicated electrical line with a 15
amp breaker.
Always use a weatherproof-covered receptacle. Re-
ceptacle shall be located not less than 5 feet (1.5
m) from and not exceeding 10 feet (3.0 m) from the
inside wall of the spa (NEC 680.43(A)).
1. Press the TEST button on the GFCI. The GFCI
will trip and the spa will stop operating.
2. Press the RESET button on the GFCI. The GFCI
will reset and the spa will turn back on.
Do not use extension cords. Using an extension cord
will void your warranty.
The spa is now safe to use.
Do not bury the power cord. If your cord becomes
damaged, replace it before next usage.
If the GFCI trips while the spa is in use, press the
RESET button. If the GFCI does not reset, unplug the
spa and call your local Cal Spas dealer for service. DO
NOT USE THE SPA!
If you need to replace your cord, replace it with a 15
amp GFCI connection. The cord may not be longer
than 15 feet (4.6 m).
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Filling and Powering Up Your Portable Spa
Never fill your spa with soft water.
Soft water makes it impossible to maintain the proper water chemistry and may cause the wa-
ter to foam, which will ultimately harm the finish of the spa and void your warranty.
1. Once the spa has been placed on an approved
surface and has been correctly wired by a licensed
electrician, inspect all plumbing connections in the
equipment area of your spa. Ensure that these
connections are secure and that they did not loos-
en during shipment.
5. Presoak the filters in spa water.
VERY IMPORTANT!
You must presoak the filters before
inserting them in the filter canister.
Dry filters can allow air into the fil-
tration system which can cause pump
failure.
2. If equipped, open all gate valves in the equipment
area. Before operating the spa, these valves must
be in the up or “open” position.
6. Once the water is at the correct level and air is
bled, plug in the spa into a dedicated electrical
outlet.
VERY IMPORTANT!
Never run the spa with the gate valves
closed or without water circulating for
long periods of time. Be careful not to
over-tighten the plumbing fittings.
Note: When the power is turned on to the spa,
the controls will perform a diagnostic check for
approximately five minutes. When the diagnostic
is complete, the spa will automatically operate at
filter speed and continue heating until the spa wa-
ter temperature reaches the default temperature
of 100˚F.
3. Remove the cartridge from filter canister.
4. Place a garden hose in the filter canister and fill
your spa with regular tap water about six
inches from the top.
8. If no water is flowing when the pump is running,
there could be an air pocket at the suction side of
the pump. Shut off power to the spa and loosen
the pump union on the suction side of the pump
to bleed the air. When air is bled, turn power
back on.
VERY IMPORTANT!
Always fill the spa through the filter
canister! Failure to do so may cause
air to be trapped in the filtration sys-
tem and prevent the pumps from op-
erating properly.
9. Install the pre-soaked filters into the filter canis-
ter.
The spa is now ready for use.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Operating Your Spa
Electronic Control Operation
Initial Start up
When first powered up, your spa will perform a self-diagnostic check and to into priming mode. The topside will
display PR to indicate this. Priming mode will be active for less than five minutes. When the spa has finished
priming, the heater will be activated and the water temperature will be maintained in standard mode. The spa
will heat to 100°F (37.5°C) at start up until the set temperature is changed as described below.
Temperature Adjustment
(Range 80°F to 104°F, 26°C to 40°C)
The electronic control panel displays the ac-
tual water temperature in degrees Fahren-
heit. The displayed temperature will only be
current after the pump has been running for
at least two minutes.
To display the temperature that the spa is
set to:
Switching Modes
•
Press either the Up or Down button. The tem-
perature setting will flash.
•
Press either the Up or Down button followed by
the Light button.
•
While the display is flashing, each time you press
the Up or Down button, the set temperature will
change up or down one degree.
•
Press the same sequence to switch to the next
mode.
Standard, Economy and Sleep Heating
Modes
Jets
Press the Jets button:
Your new spa is equipped with a heating feature that
gives you complete control of the heating system.
When the spa is powered up, it will automatically start
in standard heating mode.
•
•
•
Once to activate low speed pump.
Twice to activate high speed.
Three times to turn pump off.
• St will light briefly on the main display. In this
Light
mode, the heating system will automatically main-
tain the set spa temperature. In the economy- Press the Light button to turn on the light. Press it
heating mode, the heating system will only acti- once again to turn the light off. All optional lighting
vate during filtration times.
such as the control panel light and cabinet perimeter
lighting is controlled by the Light button and will turn
on and off with the spa light.
• Ec will display solid if temperature is not current
and will alternate with spa temperature if mea-
sured temperature is current.
Automatic Time outs
These features will automatically turn themselves off
during periods of continuous use:
•
Economy mode will heat the water to the set tem-
perature while Sleep mode, indicated by a SL on
the main display, will also only activate the heater
during the filtering cycles but will only heat the
water to within 20°F (10°C) of the set tempera-
ture. Like Economy mode, SL will display solid
when temperature is not current and will alternate
with actual temperature when it is current.
•
•
•
Low speed pump
High speed pumps
Spa light
After 2 hours
After 15 minutes
After 4 hours
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Setting Filtration Cycles
Your spa is programmed to filter twice a day. The When power has been restored, press either the Up
first cycle will begin 6 minutes after the spa is turned or Down button then the Jets button. Press either
on and the second cycle 12 hours later. The factory the Up or Down button again to change the filtering
has programmed the cycle to last for 2 hours but cycle duration. When desired duration is selected
this can be switched to 4, 6, or 8 hours depending press the Jets button to exit.
on your requirements. The default filter time is two
The low speed pump will run for the duration of the
hours.
filtering cycle and if an ozone system is installed it
To set filtration time, turn off the power to the spa will be activated. During filtering, FC will appear on
at the time of day you would like one of the filtration the main display.
cycles to begin, then turn back on after 30 seconds.
Your new spa comes equipped with an electric heater. Following the directions listed below will ensure the
most efficient operation:
NOTE: This method is only for spa usage under two hours a week.
•
Keep the spa’s operating temperature 5˚F below the desired usage temperature when not in use. One
or two hours before use, set the temperature to the desired temperature.
•
If the spa usage exceeds two hours a week, the set temperature should remain at the desired usage
temperature.
Allowing the water temperature to lower more than 10˚F below the desired usage temperature and reheating
it prior to usage will cause the heater to operate longer than it normally would maintaining the desired tem-
perature. Doing this will increase your operating cost and makes your heater work more than necessary.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Diagnostic Messages
Message
Meaning
Action Required
No message 1) Spa temperature is unknown.
on display
1) After pump has been running for 2 minutes tem-
perature will be displayed.
2) Spa is in Economy or Sleep
mode.
2) In Economy or Sleep mode, the pump may be off
for hours outside a filter cycle. If you wish to see the
current spa temperature, either switch to Standard
mode or turn Jets1 on for at least two minutes.
3) Power has been cut off to the
spa.
3) The control panel will be disabled until power re-
turns. Spa settings and time of day will be preserved
for 30 days with a battery back-up.
dr
Insufficient water detected in
heater. Spa will be shut down for
15 minutes.
Check water level in spa. Refill if necessary. Make
sure pumps are been primed and filter cartridges are
clean. Press any button to reset or wait 15 minutes
and spa will automatically reset. If message spa does
not reset, call your dealer or service organization.
drY
Insufficient water detected in
heater. Spa is shut down.
Follow directions for dr message and press any button
to reset spa. Spa will not automatically reset when dry
or dY is displayed.
(Displays on third occurrence of dr
message.)
Ec
Indicates heater is in Economy
Mode.
None.
--
Temperature unknown
After the pump has been running for two minutes, the
temperature will be displayed.
HFL
A difference in readings between
temperature sensors has been
Make sure spa is filled to proper level and that pumps
are primed and filter cartridges are clean. If message
detected indicating a possible water does not reset, call your dealer or service organiza-
flow problem. tion.
ICE
LF
Potential freeze condition detected. No action required. The pumps and the blower will
automatically activate regardless of spa status.
Persistent low flow problems.
Follow action required for HL or HFL message. Heat-
Heater is shut down, but other spa ing capacity of the spa will not reset automatically.
functions continue to run normally. Press any button to reset.
Displays on the fifth occurrence of
the HL or HFL message within 24
hours.
OHS
Overheat protection. The spa has
shut down. One of the sensors
has detected that the spa water is
110°F.
DO NOT ENTER THE WATER. Remove the spa cover
and allow water to cool. At 107°F, the spa should
automatically reset. If spa does not reset, shut off
the power to the spa and call your dealer or service
organization.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Message
OHH
Meaning
Action Required
Overheat protection (spa is shut-
down). One sensor has detected
118˚F (48˚C) at the heater.
DO NOT ENTER THE WATER!
Remove the spa cover and allow spa to cool below
107˚F (42˚C). Press any button on the topside dis-
play to reset spa. If spa will not reset after spa has
cooled, turn off power for approximately 30 seconds
and then turn power back on. If display message is
repeated then shut the power off to the spa and call
your dealer or service organization.
Pr
When your spa is first actuated, it
will go into priming mode.
The priming mode will last for up to four minutes and
then the spa will begin to heat and maintain the water
temperature in the Standard mode.
SL
Indicates heater is in Sleep Mode.
None.
SnA
Snb
Spa is shut down. The sensor that
is plugged into the sensor “A” or
“B” jack is not working.
If the problem persists, contact your dealer or service
organization. (May appear temporarily in an overheat
situation and disappear when the heater cools.)
SnS
Sensors are out of balance.
Contact your dealer or service organization.
•
If this is alternating with the
temperature, it may just be a
temporary condition.
•
If the display shows only this
message (periodically blinking),
the spa is shut down.
ST
Indicates heater is in Standard
Mode.
None.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Jets
LED Light Operation
Almost all of the jets in your spa are adjustable.
Rotating the face of an adjustable jet to the left
(counter-clockwise) will decrease the amount of
water flow through the jet. Rotating the face of an
adjustable jet to the right (clockwise) will increase
the amount of water flow through the jet. (See ex-
ample shown below.)
Press the LIGHT button on the topside control pan-
el to turn the spa light on. If your spa has LED
lights, they will also light up at the same time as
the spa light.
The LED lights operate in three three modes:
1 Cycle: The first time you press the LIGHT but-
ton, the lights will cycle through all the colors
in this order:
Neck jets adjust in the opposite directions (counter-
clockwise to increase, clockwise to decrease).
White
Cyan
Magenta
Blue
Yellow/green
Green
Red
To cycle through the different color choices,
press the button repeatedly. Each time you
press the button, you advance to the next col-
or.
2 Flashing white: When you have cycled
through all the colors, the next time you push
the LIGHT button, the LED lights will flash
white.
3 Fading cycle: The next time you push the
LIGHT button, the lights will gradually fade
from one color to the next in the order shown
above.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Clear Water Plan
This section is intended for new spa owners with
no experience with water chemistry. Everyone’s ex-
perience with maintaining water quality is different,
but there are some general concepts you need to
know.
Contents of this section:
Testing and Adjusting Spa Water
Sanitation
Filtration
Bather Load
Water maintenance is not difficult, although it re-
quires regular attention. The most important thing
to understand about taking care of your spa water is
that preventive action is much easier than correcting
water quality issues.
Starting the Spa with Fresh Water
Maintenance Schedule
Troubleshooting Water Clarity Problems
The Key to Clear Water
Excellent water quality is a simple matter of four things:
Regularity
Regularity
FiFltilrtraattiioonn
Ing et augait alit esto dolut dio doleniam quat am vel etue
Ing et augait alit esto dolut dio doleniam quat am vel etue
Clear water requires regular maintenance.
Cleaning your filter regularly is the easiest
vendiam quis duip ea ating et utem quam, sendit, velesequi-
Establish a routine based on a regular
sit am dunt niscil ilit alit nonumsan utatin utat num voloreril
vendiam quis duip ea ating et utem quam, sendit, velesequi-
and most effective single thing you can do
sit am dunt niscil ilit alit nonumsan utatin utat num voloreril
schedule for your spa water maintenance.
to keep your water clear.
consequi tinim ilisi bla feuis euguerc ilisi.
in ut pratie dionull umsandio consed dolumsandit at. Rat,
in ut pratie dionull umsandio consed dolumsandit at. Rat,
consequi tinim ilisi bla feuis euguerc ilisi.
Maintaining your water quality helps the en-
A clogged or dirty filter will cause the heater
Em verit iliqui endiam nulluptat lamcore minibh elestio num-
joyment of your spa and extends your spa’s
sandip eraesectem diatio ercing ea cortis delissed dunt
Em verit iliqui endiam nulluptat lamcore minibh elestio num-
and pump to work harder than they need
sandip eraesectem diatio ercing ea cortis delissed dunt
life by preventing damage from neglect and
to, possibly causing them to fail.
utpatisi.
utpatisi.
chemical abuse.
Ut vel ut wis atis nonullut augiam augait lore dolore erci te ea
Ut vel ut wis atis nonullut augiam augait lore dolore erci te ea
The spa’s heating system will only function
consequat.
consequat.
See page 17 for the sched-
with the proper amount
Met prate er sit dolor iriureetuer si.
Met prate er sit dolor iriureetuer si.
ule of recommended main-
of water flow through the
Feummy nullamcore magna ad dio er
Feummy nullamcore magna ad dio er
tenance.
system.
sequamconum nis eu feugiamet, vent
sequamconum nis eu feugiamet, vent
et wisis ero dolore dip exeraestie estie
vel inisci elisl ut diat, cons aut alit lut
lore tin hent adiam iustrud molor
sustis essit wiscilit wisi.
et wisis ero dolore dip exeraestie estie
See page 15 for filter clean-
vel inisci elisl ut diat, cons aut alit lut
y
F
i
t
i
l
r
t
ing instructions.
r
a
a
l
lore tin hent adiam iustrud molor
t
u
i
o
sustis essit wiscilit wisi.
g
n
e
R
our Key
Y
e
c
S
r
n
e
a
n
a
o Cleat r
l
a
Chemical Balance
T
a
Sanitation
Chemical Balance
Sanitation
i
W
t
B
a
l
t
a
i
o
Ing et augait alit esto dolut dio dole-
You will need to test and
Sanitizers kill bacteria and
c
Ing et augait alit esto dolut dio dole-
i
n
m
e
h
C
niam quat am vel etue vendiam quis
niam quat am vel etue vendiam quis
adjust the chemical bal-
viruses and keep the water
duip ea ating et utem quam, sendit,
duip ea ating et utem quam, sendit,
ance of your spa water. Al-
clean. A low sanitizer level
velesequisit am dunt niscil ilit alit non-
velesequisit am dunt niscil ilit alit non-
though this is not difficult,
will allow microbes to grow
umsan utatin utat num voloreril in ut
umsan utatin utat num voloreril in ut
pratie dionull umsandio consed
it needs to be done regu-
quickly in the spa water.
pratie dionull umsandio consed
dolumsandit at. Rat, consequi tinim
dolumsandit at. Rat, consequi tinim ilisi bla feuis euguerc ilisi.
larly.
ilisi bla feuis euguerc ilisi.
We recommend using either chlorine or bro-
Em verit iliqui endiam nulluptat lamcore minibh elestio num-
Depending on your choice of sanitizer, you
mine as your sanitizer.
Em verit iliqui endiam nulluptat lamcore minibh elestio num-
sandip eraesectem diatio ercing ea cortis delissed dunt
sandip eraesectem diatio ercing ea cortis delissed dunt
need to test the level of calcium hardness,
utpatisi.
Spa owners with an ozonator also need to
utpatisi.
total alkalinity, and pH. Spa owners with
Ut vel ut wis atis nonullut augiam augait lore dolore erci te ea
add sanitizer, although their requirements
Ut vel ut wis atis nonullut augiam augait lore dolore erci te ea
a Cal Clarity bromine generator also need
consequat.
consequat.
are different.
to check total dissolved solids and phos-
Met prate er sit dolor iriureetuer si. Feummy nullamcore
Met prate er sit dolor iriureetuer si. Feummy nullamcore
magna ad dio er sequamconum nis eu feugiamet, vent et
phates.
See page 13 for learn how to use sanitizer.
magna ad dio er sequamconum nis eu feugiamet, vent et
wisis ero dolore dip exeraestie estie vel inisci elisl ut diat, cons
aut alit lut lore tin hent adiam iustrud molor sustis essit wis-
cilit wisi.
wisis ero dolore dip exeraestie estie vel inisci elisl ut diat, cons
See page 13 for learn how to balance your
aut alit lut lore tin hent adiam iustrud molor sustis essit wis-
spa water.
cilit wisi.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Testing and Adjusting Spa Water
You have two types of testing methods to choose from:
•
The reagent test kit is a method which provides a high level of accuracy. It is available in either liquid
or tablet form.
•
Test strips are a convenient testing method commonly used by spa owners.
Balancing the Total Alkalinity
Balancing the Calcium Hardness
Total alkalinity (TA) is the measure of the total lev-
els of carbonates, bicarbonates, hydroxides, and
other alkaline substances in the water. TA can be
considered a “pH buffer”. It is the measure of the
ability of the water to resist changes in pH level.
Calcium hardness (CH) is a measure of the total
amount of dissolved calcium in the water. Calcium
helps control the corrosive nature of the spa’s wa-
ter and is why soft water is not recommended. The
low calcium content of soft water is very corrosive
to the equipment and can cause staining of the spa
shell.
The recommended total alkalinity is 80 - 120
ppm
The recommended calcium hardness is 150
- 200 ppm
If the TA is too low, the pH level will fluctuate wide-
ly from high to low. Low TA can be corrected by
adding Cal Spas “pH-Alkalinity Up”.
If the CH is too low, add Cal Spas “Liquid Hardness
Increaser”.
If the TA is too high, the pH level will tend to be too
high and may be difficult to bring down. High TA
can be corrected by adding Cal Spas “pH-Alkalinity
Down”.
If the CH is too high, dilute the spa water with soft
water or, if this is not available, add Cal Spas “Stain
and Scale Defense”.
When the TA is balanced, it normally remains sta-
ble, although adding water with high or low alkalin-
ity will raise or lower the TA level.
When the CH is balanced, it normally remains sta-
ble, although adding soft water or very hard water
will raise or lower the CH level.
Balancing the pH
The pH level is the measure of the balance between
acidity and alkalinity.
8.2
Too alkaline,
causes scaling
Need to lower the pH level
8.0
7.8
7.6
7.4
7.2
7.0
6.8
6.6
If the pH is too low, it can cause corrosion of metal fix-
tures and the heating element. Low pH can be corrected
by adding pH-Alkalinity Up.
Ideal balance
If the pH is too high, it can cause scaling by allowing
metals or minerals to form deposits and stain spa sur-
faces. High pH can be corrected by adding pH-Alkalinity
Down.
Too acidic,
causes corrosion
Need to raise the pH level
Testing For:
Ideal Range (ppm)
Chemicals To Use:
Minimum
Maximum
To Raise
To Lower
Total Alkalinity
80
120
pH-Alkalinity Up
pH-Alkaliity Down
Calcium Hardness
pH
150
200
Liquid Hardness Increaser
pH-Alkalinity Up
Stain and Scale Defense
pH-Alkaliity Down
7.4
7.6
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Sanitation
After you fill your spa, you need to decide which chemical sanitizer you wish to use. Consult your Cal Spas
dealer for the right decision with regards to your lifestyle and spa usage.
We recommend either bromine or chlorine as your sanitizer. Both work well when maintained regularly.
DO NOT use trichlor Trichlor is very acidic and the hot temperature of the spa causes it to
dissolve too quickly It will cause damage to your spa and will void your warranty
Sanitizers kill bacteria and other organic waste by breaking them down to non-harmful levels and are filtered
out.
Make sure you follow all instructions and use only Cal Spas brand chemicals.
Whichever plan you decide on, follow it completely and don’t take shortcuts. It will provide you with clean,
safe, clear spa water with a minimum of effort. Spa owners with the ozonator still need to use a chemical
sanitizer. See page 14 for instructions.
Using Chlorine as a Sanitizer
If you choose to use chlorine as a sanitizer, only use granulated chlorine, not liquid chlorine. We recommend
you use only Cal Spas “Chlorinating Granules”.
Once a week, check the chlorine level using either a test strip or a reagent kit. See the table on the following
page for the ideal range.
Add one or two tablespoons of Cal Spas “Chlorinating Granules” to the spa water weekly. Note that chlorine
dissipation rate will be faster at higher water temperatures and slower at lower temperatures.
When you add chlorine, open all of the jets and run the spa at high speed with the cover open for at least
30 minutes.
Follow the maintenance schedule on page page 17.
Using Bromine as a Sanitizer
Bromine is a very effective sanitizer that produces low chemical odors. Unlike chlorine, it can break down
bacteria and other impurities to a safe level with a low burn-out rate.
Bromine is available in both granulated and tablet form. Use granulated bromine to establish your bromine
base. Use tablets to maintain it. The filter cartridge provided with your spa has an internal chamber for bro-
mine tablets. Do not use a floater.
When you begin with fresh water, add 2 ounces of Cal Spas Go Brom. Open all of the jets and run the spa at
high speed. This is your base bromine level as the tablets will take a while to dissolve.
Add two ounces of Oxidizer Shock. Open all of the jets and run on high speed with the cover half open for
at least 30 minutes.
Follow the maintenance schedule on page page 17.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Testing For:
Ideal Range
(ppm)
Chemicals To Use:
Minimum Maximum
To Raise
To Lower
Chlorine level
Without ozonator
With ozonator
3.0
5.0
Chlorinating Granules
Go Brom
2.0
4.0
Bromine level
Without ozonator
With ozonator
6.7
5.7
11.0
10.0
Shocking the Water
In addition to using a chemical sanitizer, you will periodically need to shock the water. Shocking the water
helps remove burned-out chemicals, bacteria, and other organic material from your spa’s water and im-
proves your sanitizer’s effectiveness.
Do not use chlorinating shock, which will damage your spa’s jets and pump seals. The only shock you should
use is Cal Spas Oxidizer Shock. It is an easy way to maintain either chlorine or bromine chemical plans.
For best results use the directions below.
Add one ounce of Cal Spas Oxidizer Shock:
•
•
•
Once a week
After heavy bather loads
If water has a strong odor
Spa must be running with all of the jets on high for 30 minutes with the cover open. If necessary, repeat
oxidizer shock in 30 minute intervals.
Chemical Safety
Read and follow all printed instructions listed on bottles and packages Failure to
follow chemical directions may result in serious injury, sickness, or even death
Do not exceed chemical dosages as recommended have been exposed to chemical contact prior to wear-
in the Clear Water Plan or on chemical bottles and ing them again.
packages.
Inhaling or ingesting chemicals will cause serious in-
Never change chemical brands or types without com- jury, sickness, or even death.
pletely draining, flushing and thoroughly cleaning the
Chemicals must be stored completely out of the
spa and cover first.
reach of children in an area that is well vented, cool,
Never mix chemicals together.
and dry. Failure to provide a proper area for chemical
storage may result in serious injury, sickness, fire ex-
plosion and even death. Do not store your chemicals
inside the equipment area of your spa.
Do not allow chemicals to come in contact with skin,
eyes or clothing. Remove and wash clothing that may
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Cleaning the Filter
The filter is the part of your spa that removes the debris from the water and needs to be cleaned on a regular
basis to maximize your spa’s filtering performance and heating efficiency.
In addition to spraying off the filter weekly to remove surface debris, your filter should be deep cleaned pe-
riodically to dissolve scale and particles that get lodged deep within the filter fibers and impede the filtration
process. Even if the filter looks clean, scale and particles can clog the fibers and prevent water from flowing
through the filter resulting in the most common spa problem—no heat, caused by a dirty filter.
We recommend you clean your filter once a month and replace it once a year or as necessary.
1. Remove the filter by turning it counterclockwise, unscrewing the bottom threads, then pulling it up and
out.
2. Place the dirty filter into a bucket of water deep enough to cover the filter. Add 8 oz of Cal Spas “Liquid
Filter Cleaner” to the bucket of water.
Note: It is a good idea to keep a spare filter to use in the spa while the dirty filter is being deep cleaned.
This way, you can rotate the filters and both will last longer.
3. Soak the filter for a minimum of 24 hours.
4. Spray the filter with a water hose. Spray each pleat carefully.
5. Reinstall the filter. Do not overtighten.
Cleaning the Filter Basket
You will need to clean the filter basket periodically. To remove the filter basket, twist the weir skimmer
counter-clockwise and lift up to remove it. You can do this while the spa is filled, but make sure you first turn
off the jet pump.
Bather Load
“Bather Load” is the term used to describe the num- 4 people, 15 minutes of usage, three times a week
ber of people using a spa, combined with the length at 100 degrees) If your bather load exceeds these
of usage, and the frequency of usage. All these fac- guidelines, and you experience water quality prob-
tors have a great effect on the spa water. The higher lems, increase the amount of filtration first, (go to the
the bather load, the more chemicals need to be add- next higher filtration number) then if water quality
ed and a longer filtration time will be needed.
is still not adequate, consult the advice of your Cal
Spas dealer for additional chemical or system recom-
mendations. Be sure to give them your bather load
information.
All versions of the Cal Spas Clear Water Plan are
designed for spas with average bather load (3 to
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Starting the Spa with Fresh Water
We recommend you use Cal Spas chemicals only.
Other brands of chemicals may have similar names
and/or usage descriptions but due to manufacturing
differences, use of other chemicals can increase the
likelihood of under- or over-dosing the spa chemi-
cals. Damage to the spa or spa’s components from
improper chemicals or chemical usage is not covered
under the spa’s warranty.
•
Adjust total alkalinity (acceptable range is
80-120ppm).
•
Adjust pH if necessary (between 7.2 to 7.8).
5. Pour in 16 oz of Cal Spas “Metal Protector” in the
center of the spa.
6. Add Stain and Scale Prevention.
7. Add either chlorine or bromine (but not both).
Prior to filling a spa for the first time, or after a rou-
tine draining, you will want to follow this start-up
plan to extend water life and performance.
Chlorine: Add two tablespoons of Cal Spas “Chorine
Granules” to the spa water.
As with all chemical dosages listed in these Clear
Water Plans, start-up dosages are intended for 500-
gallon spas. Please adjust the chemical dosages to
the capacity of your particular spa.
Bromine: Add 2 oz of Cal Spas “Go Brom” to estab-
lish a bromine base.
Add 2 Cal Spas “Bromine Tablets” to bro-
mine floater.
1. Clean the surface of the spa with Cal Spas “Multi-
Purpose Cleaner”.
8. Turn on jets for 15 minutes. Leave spa uncov-
ered during this time.
2. Apply a protective coat of Cal Spas “Fast Sheen”
to the acrylic surface.
9. Put cover on spa and allow to heat up to desired
temperature.
3. Fill the spa to the proper water level with normal
tap water. (Do not use soft water.)
4. Use test strip and balance the spa water.
Water level is very important to the operation of your spa If the water level
is too low or too high, your spa will not operate properly The water level
should be about six inches from the top when the spa is not being used
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Maintenance Schedule
Each time you refill the spa
Follow the section “Starting the Spa with Fresh Water”.
Prior to each use
Test the spa water using either test strips a reagent test kit. Adjust
chemical levels as necessary.
Once a week
Test the spa water using either test strips a reagent test kit. Adjust
chemical levels as necessary.
Once a month
Deep clean your spa’s filter. (Follow filter cleaning instruction at
beginning of Clear Water Plan)
Every two to four months
Drain and clean your spa with “Multi-Purpose Cleaner”.
Polish the acrylic surface with “Fast Sheen”.
Clean and treat spa cover with “Cover Protector”.
Refill your spa, following the section “Starting the Spa with Fresh
Water”.
Once a year
Replace filter cartridges if the pleats appear frayed.
We recommend that your spa water be changed every 4 to 6 months. You may find the need to change your
spa water more frequently with heavy use. When empty, your spa should be cleaned with a non-abrasive
cleaner, such as Cal Spas™ All Surface Cleaner, and then rinsed thoroughly.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Troubleshooting Water Clarity Problems
Problem
Probable Causes
Possible Solutions
Cloudy Water
•
Dirty filter
•
Clean filter
•
Excessive oils / organic mat- • Shock spa with sanitizer
ter
•
•
Add sanitizer
•
•
Improper sanitization
Adjust pH and/or alkalinity to recommended
Suspended particles / organ-
ic matter
range
•
•
•
•
•
•
•
•
Run jet pump and clean filter
Drain and refill the spa
•
Overused or old water
Water Odor
•
•
•
•
•
•
Excessive organics in water
Improper sanitization
Low pH
Shock spa with sanitizer
Add sanitizer
Adjust pH to recommended range
Shock spa with sanitizer
Adjust pH to recommended range
Chlorine Odor
Musty Odor
Chloramine level too high
Low pH
Bacteria or algae growth
Shock spa with sanitizer – if problem is vis-
ible or persistent, drain, clean and refill the
spa
Organic buildup /
scum ring around
spa
•
Buildup of oils and dirt
•
Wipe off scum with clean rag – if severe,
drain the spa, use a spa surface and tile
cleaner to remove the scum and refill the spa
Algae Growth
•
•
High pH
•
•
Shock spa with sanitizer and adjust pH
Low sanitizer level
Shock spa with sanitizer and maintain sani-
tizer level
Eye Irritation
•
•
Low pH
•
•
Adjust pH
Low sanitizer level
Shock spa with sanitizer and maintain sani-
tizer level
Skin Irritation / Rash
•
•
Unsanitary water
•
•
Shock spa with sanitizer and maintain sani-
tizer level
Free chlorine level above 5
ppm
Allow free chlorine level to drop below 5 ppm
before spa use
Stains
Scale
•
•
•
Total alkalinity and/or pH
too low
•
•
Adjust total alkalinity and/or pH
Use a stain and scale inhibitor
High iron or copper in
source water
High calcium content in
water – total alkalinity and
pH too high
•
•
Adjust total alkalinity and pH – if scale re-
quires removal, drain the spa, scrub off the
scale, refill the spa and balance the water
Use a stain and scale inhibitor
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Cleaning and Maintenance
Removing the Access Panel
You will need to remove the access panel in order to drain your Genesis spa.
1. Unplug the spa.
2. Remove the screws from the access panel.
3. Remove the access panel and set it aside.
Replace the access panel when you are finished. Do not overtighten the screws.
Do not run the spa with the access panel removed!
Draining Your Portable Spa
Your spa should be drained every four to six months and refilled
with fresh tap water. The following is the recommended method
for draining your spa.
1. Turn off the power at the breaker.
2. Remove the filter.
3. Remove the access panel as described above.
4. Locate hose ending with the 3/4 inch hose-bib fixture.
5. Hook up the female end of a garden hose to the drain fit-
ting.
6. Place the other end of the garden hose where you would like
the water to drain to.
7. Twist the hose-bib fixture counterclockwise to open the
drain.
8. Let the spa drain completely, then remove the garden hose.
9. Twist the hose-bib fixture clockwise to close it.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Winterizing (Cold Climate Draining)
In many areas of the country, the temperature drops 1. Open all filter covers.
below 32˚F (0°C). We recommend that you always
2. Remove the filter baskets and filters.
have your spa full of water and running at normal spa
temperatures (80˚F to 100˚F, 26.7°C to 37.8°C). This
will help reduce the risk of freezing in your spa and
your spa’s equipment.
3. Drain your spa completely as described in the in-
structions above.
4. Remove drain plugs from the front of the
pumps.
Warning: If you find the need to drain your spa,
please be aware of the potential of freezing in 5. Disconnect the unions from both sides of the
your spas equipment and plumbing Even if the
directions below are followed perfectly, there
is no guarantee that your spa will not suffer
freeze damage
pump.
6. Use a wet/dry vacuum to blow any remaining
water out of the jets and equipment area.
Cover your spa with a good spa cover and an all-
weather tarp to ensure that neither rain nor snow
enters the spa.
Freeze damage is not covered by your war-
ranty
Installing Cover Latches
You will need a drill with a 3/32” drill bit and a Phillips screwdriver.
Your cover will have four clips attached to the ends of the four latches, two on each end of the spa cover.
There will also be a small bag with 12 screws.
1. Place the cover on the spa with the latches placed
where you want to mount them on the spa.
2. Using the latch clips as a guide, drill three
holes for the mounting screws.
3. Insert three screws in the latch clip and fasten it to the spa shell.
Make sure they are snug, but do not overtighten them. Do the
same for the remaining latches. Drill and attach latch clips to the
shell one at a time.
4. When you have finished inserting
all of the screws, use the latch
key to unlock the cover latches.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Covering Your Spa
Important! Keep the spa covered when not in use!
•
•
•
•
Covered spas will use less electricity in maintaining your set temperature.
Covering your spa will protect your spa’s finish from the sun’s ultraviolet rays.
You are required to keep the spa covered to maintain warranty coverage.
Covering your spa helps prevent children from drowning in the spa.
See the manual enclosed with your cover for instructions on mounting the locks and how to lock and unlock
the cover.
In addition, while the spa cover is rigid, it is not designed to support any weight. Therefore, as a safety
precaution and to preserve the life of your cover, you must not sit, stand, or lie on it, nor should you place
objects of any kind on top of it.
Cleaning and Replacing the Filter
Filtration is one of the most important steps you can take to ensure clean, clear water. It is far less expensive
to fix water clarity problems by filtering your spa than by using excessive amounts of chemicals, excessive
filtration times, or by water replacement.
In addition, you need to regularly clean out the filter basket mounted on top of the filter well.
See the section “Clear Water Plan” on page 11 for more information on cleaning your filter.
Cleaning the Cover
Vinyl and Leather Cleaner
Because the cover is constantly exposed to weather, you should protect it as part of your
monthly maintenance plan. Cal Spas Vinyl and Leather Cleaner is specifically designed to
protect spa covers from chemical and ultraviolet light damage. It accomplishes this without
leaving an oily residue behind that is normally associated with common automotive vinyl
protectants. Cal Spas Vinyl and Leather Cleaner should be used sparingly. Incorrect usage
may cause water clarity issues.
Periodic Maintenance
1. Remove spa cover from spa.
2. Allow spa cover to dry completely.
3. Spray Vinyl and Leather Cleaner to cover evenly and wipe dry.
4. Allow spa cover to dry completely.
5. Reinstall cover on spa.
Warning: Do not use automotive vinyl protectants on spa covers. These products are generally oil-based
and will cause severe water clarity issues that are difficult to correct.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Cleaning the Shell
All-Purpose Cleaner (Spa Finish Cleaning)
Cal Spas All-Purpose Cleaner is an essential part of maintaining your spa’s finish. Through
normal use, the spa’s finish can accumulate dirt, oil, and calcium causing a rough feel and
unsightly scum lines. Cal Spas All-Purpose Cleaner is a low detergent, non-abrasive cleaner
specifically formulated to clean the spa without damaging its acrylic finish.
The most effective solution to minimize cleaning time is prevention. When the following steps
are followed, the spa’s finish will actually start to resist most of the elements that cause cal-
cium build-up and make scum line clean up easier.
Prior to Spa Start-Up and Refilling
Periodic Maintenance
1. Spray Cal Spas Multi-Purpose Cleaner directly on 1. Spray Cal Spas Multi-Purpose Cleaner directly to
to the spa’s finish.
the spa’s finish.
2. Wipe clean with a clean soft cloth.
3. Repeat on heavily calcified areas.
2. Wipe clean with a clean soft cloth.
3. Wipe spa thoroughly with a wet sponge, rinsing
often in a bucket of clean water.
4. Wipe spa thoroughly with a wet sponge, rinsing
often with a bucket of clean water.
Cal Spas Multi-Purpose Cleaner should not be sprayed
directly into the spa water. Incorrect usage of this
product will cause water clarity issues.
5. Allow spa to dry completely.
6. Apply a coat of Cal Spas Fast Sheen to the spa’s
entire finish with a soft towel or sponge.
7. Allow Fast Sheen to dry until white and pow-
dery.
8. Buff clean with a soft cloth, rotating frequently.
Fast Sheen (Spa Finish Protecting Wax)
Cal Spas Fast Sheen is an essential part of maintaining your spa’s finish. Through normal use,
the spa’s finish can accumulate dirt, oil, and calcium, causing a rough feel and unsightly scum
lines. Cal Spas Fast Sheen is a non-oil based wax that is specifically formulated to protect the
spa’s finish from the chemicals and minerals associated with normal spa use.
The most effective solution to minimize cleaning time is prevention. When the following steps
are followed, the spa’s finish will actually start to resist most of the elements that cause cal-
cium build-up and make scum line clean-up easier.
6. Apply a coat of Cal Spas Fast Sheen to the spa’s
Prior to Spa Start-Up and Refilling
1. Spray Cal Spas Multi-Purpose Cleaner directly to
entire finish with a soft cloth or sponge.
the spa’s finish.
7. Allow Fast Sheen to dry until white and pow-
dery.
2. Wipe clean with a soft cloth.
8. Buff clean with a soft cloth, rotating frequently.
3. Repeat on heavily calcified areas.
IMPORTANT: Cal Spas Fast Sheen should not be used
on spas full of water. Only apply to clean, cool, dry
surfaces. Incorrect product usage may cause water
clarity issues.
4. Wipe spa thoroughly with a wet sponge, rinsing
often in a bucket of clean water.
5. Allow the spa to dry completely.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Appendix
Replacement Parts
Jets
Light
EW 2” Euro
Light Mini 2” Diameter
Standard gray PLU21703420
Stainless steel PLU21703621
mfw 3” Micro Flow
LIT16000151
Standard gray PLU21703432
Stainless steel PLU21703631
Covers
G418T
G318R
72” x 72”
OZ 2” Ozone Injector
Standard gray PLU21700818
78” Round
Drain
Main Drain, Super Hi Flo
Suction 2” Silver
G518L
80” x 80”
Standard Rust
ACC01200495
PLU21400132
G618B
84” x 76”
Waterfall
Waterfall
PLU21800700
Filters
Filter Cartridge, 50 Sq Ft,
Anti-Bacterial
FIL11100201
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
24
2009 Warranty
This limited warranty is effective for Genesis portable spas manufactured after January 14, 2009.
Cal Spas portable spas are warranted to be free from defects in material and workmanship. This warranty starts
from date of manufacture and ends either by specified time-frame listed below, owner-transfer, reloca-
tion, or installation of any component other than by manufacturer.
This limited warranty is only valid on portable spas delivered in the United States and Canada. However, it does
not apply to special offers and events and extends through the selling dealer to the original purchaser at the
original site of installation.
Spa Shell / Structural
LMS warrants against the loss of water through the spa shell due to defects in materials and/or workmanship
for a period of one year.
Interior Surface
LMS warrants against cracks, blisters, peeling, discoloration and delamination of interior surfaces for a period
of one year.
Equipment
LMS warrants the spa’s electrical and electronic components, specifically, the control system and pumps, against
malfunction due to defects in materials and/or workmanship for a period of one year.
Components
LMS warrants manufacturer-installed ozonator and LED light source against malfunction due to defects in ma-
terials and/or workmanship for one year.
Manufacturer Warranty
Spa cover warranty is extended through the manufacturer of the product. Spa cover is warranted for 90 days
unless otherwise specified. For more information, see their warranties in the owner’s information package that
was delivered with your spa for more information.
Warranty Performance
In the event of a malfunction or defect covered under the terms of this warranty, the factory authorized selling
dealer is responsible for performing all necessary repairs. To obtain service, contact the selling dealer. In the
event the consumer is unable to obtain satisfactory customer service from the selling dealer, written notification
must be given to the LMS Customer Relations Department within 30 days of the reported failure.
In the event of any warranty replacement, all labor costs (not limited to removal, replacement, and installation)
and shipping costs are the responsibility of the spa owner. There will be no charge for parts on a covered item.
However, the LMS Service Agent may assess a reasonable travel or mileage charge per service call, which may
include diagnostic time. If LMS determines that repair of a covered item is not feasible, LMS reserves the right to
replace the defective merchandise with merchandise equivalent or equal in value to the original merchandise.
Warranty Limitations and Exclusions
The limited warranty applies only to spas normally used for personal, family or household purposes.
This warranty specifically excludes factory installed plumbing. Replaceable service items, such as filters, light
bulbs, and jet inserts are specifically excluded from the limited warranty.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
25
This warranty is void if the spa has been subject to neg-
ligence, alteration, misuse, abuse, repairs by non-LMS
authorized personnel, incorrect electrical installation,
installation by unqualified personnel, installation with-
out a permit if required by local codes, installation of
any component other than by the manufacturer, acts of
God (including, but not limited to, acts of nature and
surrounding environments), and any other cases beyond
the control of LMS.
•
•
Damage caused by incorrect electrical installation,
electrical brownout, voltage spikes, or operation
of spa out of voltage range by more than ±10%
Spas improperly installed or placed on non-ap-
proved surfaces
Although shell cracks, which are breaks in the shell
that go all the way through, are covered by this limited
warranty, cosmetic scratches, gouges and crazing are
not considered cracks and are not covered.
Examples of common acts invalidating this warranty
include, but are not limited to:
For relocating your spa without voiding your warranty,
contact Customer Service for relocation procedures.
•
•
•
Use of spa in a non-residential application
Scratches caused by normal use
Equipment adjustments (such as pressure switch ad-
justments) are specifically excluded from this war-
ranty.
Operation of spas water temperature out of the
normal operating range of 32˚F (0°C) to 118˚F
(47.8°C)
Disclaimers
•
•
Damage caused by incorrect water level (low,
overflow, etc.)
This limited warranty is made with the express un-
derstanding that the spa is not an essential device or
medical device as defined under State and Federal
Law. LMS shall not be liable for loss of use of the spa
or other incidental or consequential costs, expense or
damages, which may include but are not limited to
removal of permanent deck or other custom fixtures
or the necessity for crane removal. Any implied war-
ranty shall have duration equal of the applicable war-
ranty stated above. Under no circumstances shall LMS
or any of its representatives be held liable for injury
to any person or damage to any property, however
arising.
Damage caused by extreme weather conditions
(hot, cold, etc.)
•
•
Damage caused by dirt, sand and calcium
Damage caused by clogged filter cartridges (see
filter cleaning instructions in this owner’s manual)
•
•
Damage caused by continued operation of this
spa with either a known or an unknown problem
Damage caused by tri-chlor, acids, chlorine tab-
lets, any floating chemical devices, or any spa
chemicals not authorized by LMS
Legal Remedies
This limited warranty gives you specific legal rights
and you may have other rights, which may vary from
state to state.
•
Damage caused by improper water chemistry
(high levels of chlorine, bromine, calcium, pH and
other excessive chemical levels)
•
•
Damage caused by direct sunlight. Spas should
always be covered when not in use
Customer Service
See your Cal Spas dealer for a copy of the applicable
warranty, details, and any questions you may have re-
garding the warranty coverage on your spa.
Damage caused as a result of failure to follow op-
erating instructions as defined within this owner’s
manual
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Cal Spas Chemicals
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2009 Genesis Portable Spa
LTR20091058, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating the product serial number
The serial number of your spa is located on a metal plate attached to the
base of the equipment pack inside the equipment area of the spa. You
will need this number to properly register your spa and activate coverage.
Write this information in the space provided below.
Spa Model: __________________________________________________
Spa Serial Number: ___________________________________________
Date Purchased: _____________________________________________
Date Installed: _______________________________________________
Dealer’s Phone Number: _______________________________________
Dealer’s Address: _____________________________________________
CONTACT INFORMATION
LMS Customer Service Department
1462 East Ninth Street
Pomona, CA 91766.
For customer service, please contact
your authorized dealer immediately. If
you need additional information and/or
assistance, please contact:
Toll Free: 1-800-CAL-SPAS
Fax: 1-909-629-3890
www calspas com
Download from Www.Somanuals.com. All Manuals Search And Download.
|
