CSMIM-T1
SN
1-8
17-24
STAT S/U
ATTN TRAF
MODEM
CONFIG
STATUS
9-16
CD TX RX
A
B
C
1
2
3
4
5
SET UP
6
7
8
9
10
11
12
13
CONSOLE
MODEM
PORT
STATUS
14
15
16
CSMIM-T1 HARDWARE
INSTALLATION GUIDE
17
18
19
20
21
22
23
24
TEST
LOS
BLU
SYNC
NETWORK
STATUS/
ALARMS
RED
YEL
ON LINE
T1 NETWORK
INTERFACE
DROP/INSERT
INTERFACE
DI SYNC
ETHERNET
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other
information contained in this document without prior notice. The reader should in all cases
consult Cabletron Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without
notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY
INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING
OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED
IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR
SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
© Copyright April 1997 by:
Cabletron Systems, Inc.
P.O. Box 5005
Rochester, NH 03866-5005
All Rights Reserved
Printed in the United States of America
Order number: 9032222 April 1997
MMAC and CSMIM-T1 are trademarks of Cabletron Systems, Inc.
Annex, Annex Three, Annex3, Remote Annex 6000 and Remote
Annex 6100 are trademarks of Xylogics, Inc.
Portions subject to copyright by Microcom Systems, Inc. 1993-1995.
Used by permission.
All other product names mentioned in this manual may be trademarks or
registered trademarks of their respective companies.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment uses, generates, and can radiate radio frequency
energy and if not installed in accordance with the operator’s manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference in which case the user will be required to correct the
interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment complies with FCC Rules Part 68. The FCC Registration Number is
located on the front of the CSMIM-T1.You must provide this information to the telephone
company if requested.
FCC Registration Number
3N9USA-22587-DD-N
iv
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice to Users of T1 Service
The following instructions are provided to ensure compliance with the Federal
Communications Commission (FCC) Rules, Part 68.
1.) All direct connections to T1 lines must be made using standard plugs and
jacks.
2.) Before connecting the unit, you must inform the local telephone company
of the following information:
Port ID
REN/SOC
6.0Y
FIC
USOC
RJ48C
CSMIM-T1
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1ZN
04DU9-1SN
(Network Port)
CSMIM-T1 (Drop
and Insert Port)
6.0P(XD)
N/A
3.) If the unit appears to be malfunctioning, it should be disconnected from the
telephone lines until you learn if your equipment or the telephone line is
the source of the trouble. If your equipment needs repair, it should not be
reconnected until it is repaired.
4.) The CSU/DSU has been designed to prevent harm to the T1 network. If the
telephone company finds that the equipment is exceeding tolerable
parameters, the telephone company can temporarily disconnect service,
although they will attempt to give you advance notice if possible.
5.) Under FCC Rules, no customer is authorized to repair this equipment. This
restriction applies no matter whether the equipment is in or out of warranty.
6.) If the telephone company alters their equipment in a manner that will affect
use of this device, they must give you advance warning so as to give your
company the opportunity for uninterrupted service. You will be advised of
your right to file a complaint with the FCC.
7.) In the event of equipment malfunction, all repairs should be performed by
our company or an authorized agent. It is the responsibility of users
requiring the service to report the need of service to our company or to one
of our authorized agents.
CSMIM-T1 Hardware Installation Guide
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Equipment Attachment Limitations
NOTICE: The Indusrty Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective
operational and safety requirements. The Industry Canada does not guarantee the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. In some cases the company’s inside
wiring associated with a single line individual service may be extended by means of a
certified connector assembly (telephone extension cord). The customer should be aware
that compliance with the above conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company cause
to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines, and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage of the
load to be connected to a telephone loop which is used by the device, to prevent
overloading. The termination on a loop may consist of any combination of devices subject
only to the requirement that the total of the Load Numbers of all the devices does not
exceed 100.
Industry Canada Certification Number
2179 6790A
IC NOTICE
This Class A digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appariel numerique de la classe A respecte toutes les exigences du Reglement sur le
materiel brouilleur du Canada.
vi
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
EXCLUSION OF WARRANTY
AND DISCLAIMER OF LIABILITY
1. EXCLUSION OF WARRANTY. Except as may be specifically provided by
Cabletron in writing, Cabletron makes no warranty, expressed or implied, concerning
the Program (including Its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE
SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF
MERCHANTABLITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH
RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN
MATERIALS, AND ANY ACCOMPANYING HARDWARE.
2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF
BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR
RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR
INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON
THE DURATION OR LIMITATION OF IMPLIED WARRANTEES IN SOME
INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT
APPLY TO YOU.
CSMIM-T1 Hardware Installation Guide
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
CHAPTER 1
INTRODUCTION
1.1 General........................................................................................ 1-1
1.2 Organization of This Document................................................... 1-1
1.3 Document Conventions ............................................................... 1-2
1.4 Getting Help................................................................................. 1-3
1.5 CSMIM-T1 Overview ................................................................... 1-4
1.5.1 Software Information....................................................... 1-5
1.6 CSMIM-T1 Front Panel................................................................ 1-5
1.6.1 Console Port................................................................... 1-6
1.6.2 System LED Indicators ................................................... 1-7
1.6.3 The SET UP Switch........................................................ 1-7
1.6.4 T-1 Network Access........................................................ 1-8
1.6.5 NETWORK STATUS / ALARMS .................................... 1-8
1.6.6 Modem Configuration Status LEDs ................................ 1-9
1.6.7 Modem Port Status LEDs ............................................... 1-9
1.6.8 EFS Key Number.......................................................... 1-10
1.7 Connectivity............................................................................... 1-10
1.8 Telco Connection Information.................................................... 1-10
1.8.1 Connecting the CSMIM-T1 to a Full T-1 Line ............... 1-10
1.8.2 Connecting the CSMIM-T1 to a Fractional T-1 Line ..... 1-11
1.9 Compatibility.............................................................................. 1-12
1.10 CSMIM-T1 Physical / Statistical Information ............................. 1-12
CHAPTER 2
INSTALLING THE CSMIM-T1
2.1 General........................................................................................ 2-1
2.2 Locating the Ethernet Jumpers.................................................... 2-2
2.2.1 Setting the Ethernet Jumpers ......................................... 2-3
2.2.2 Setting the Subnet Jumper ............................................. 2-3
2.3 Network Bypass Jumper.............................................................. 2-4
2.4 Installing the CSMIM-T1.............................................................. 2-5
2.5 Making Connections.................................................................... 2-7
2.5.1 Connecting a Console Terminal ..................................... 2-7
2.5.2 Connecting a T1 Network Interface ................................ 2-8
2.5.3 Connecting a Drop/Insert Interface................................. 2-9
2.6 Power-up and Test ...................................................................... 2-9
2.7 Auto-initializing the ROMs ......................................................... 2-11
2.7.1 BOOTP ......................................................................... 2-12
2.7.2 RARP............................................................................ 2-13
2.8 Software Installation Procedures............................................... 2-13
CSMIM-T1 Hardware Installation Guide
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
2.8.1 Invoking the Console Monitor........................................2-15
2.8.2 Self-Booting the CSMIM-T1 ..........................................2-15
2.8.3 Reloading EFS Key Value.............................................2-16
CHAPTER 3
ROM MONITOR COMMANDS
3.1 General ........................................................................................3-1
3.2 Commands...................................................................................3-3
3.2.1 addr .................................................................................3-3
3.2.2 boot .................................................................................3-5
3.2.3 config.............................................................................3-11
3.2.4 console-baud.................................................................3-12
3.2.5 erase .............................................................................3-13
3.2.6 help................................................................................3-14
3.2.7 image.............................................................................3-14
3.2.8 ipx..................................................................................3-15
3.2.9 lat_key...........................................................................3-16
3.2.10 mop ...............................................................................3-17
3.2.11 net .................................................................................3-17
3.2.12 option_key.....................................................................3-18
3.2.13 ping................................................................................3-18
3.2.14 ports ..............................................................................3-19
3.2.15 sequence.......................................................................3-21
3.2.16 slip.................................................................................3-22
3.2.17 stats...............................................................................3-25
CHAPTER 4
CSMIM-T1 PARAMETERS
4.1 General ........................................................................................4-1
4.2 T-1 Commands ............................................................................4-1
4.3 T-1 Parameters............................................................................4-8
4.4 Parameter Descriptions ...............................................................4-9
4.5 Set T-1 Parameters Example.....................................................4-13
CHAPTER 5
TROUBLESHOOTING PROCEDURES
5.1 General ........................................................................................5-1
5.2 Power-Up and Boot Procedures ..................................................5-4
5.2.1 Normal Mode CSMIM-T1 Diagnostics.............................5-4
5.2.1.1 Normal Mode Error-Free Sequence................5-5
5.2.1.2 Normal Mode Error Sequence ........................5-6
5.2.2 SET UP Mode .................................................................5-7
5.2.2.1 SETUP Mode Error-Free Sequence ...............5-7
5.2.2.2 SETUP Mode Error States..............................5-8
5.3 BOOT Failures.............................................................................5-9
x
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
5.3.1 Boot Error Report.......................................................... 5-10
5.3.2 Correcting CSMIM-T1 Parameters ............................... 5-13
5.3.2.1 Load Server Host Not Responding............... 5-14
5.3.2.2 UNIX Host on the LAN ................................. 5-14
5.3.2.3 Another CSMIM-T1 ...................................... 5-15
5.3.2.4 VAX VMS Load Host on the LAN................. 5-16
CSMIM-T1 Dumps.................................................................... 5-17
5.4
CHAPTER 6
MODEM GUIDE
6.1 General........................................................................................ 6-1
6.2 Features ...................................................................................... 6-2
6.3 Using the AT Command Set........................................................ 6-3
6.3.1 Key AT Command Factory Defaults ............................... 6-4
6.3.2 Establishing 11-Bit Data Connections ............................ 6-5
6.3.3 V.32bis Cellular Connections Using AT Commands ...... 6-6
6.3.3.1 Universal Cellular Setup................................. 6-6
6.3.3.2 MNP 10 V.32bis Quick Connect Cellular Only
Setup6-6
6.4 Modulation Protocols................................................................... 6-7
6.4.1 Protocol Configuration Command Settings................... 6-10
6.4.2 Speed and Protocol Connection Matrices .................... 6-11
6.5 Error Correction......................................................................... 6-14
6.6 Diagnostics................................................................................ 6-16
6.6.1 Power-Up Diagnostics .................................................. 6-16
6.6.2 Local Analog Loopback with Self-Test.......................... 6-16
6.6.3 Local Analog Loopback ................................................ 6-17
6.6.4 Remote Digital Loopback with Self-Test....................... 6-17
6.6.5 Remote Digital Loopback.............................................. 6-18
6.6.6 Local Digital Loopback.................................................. 6-18
6.6.7 Respond to Remote Digital Loopback .......................... 6-19
6.6.8 Automatically Terminating a Test: Register S18........... 6-19
6.7 Result Codes............................................................................. 6-20
6.7.1 Connection Result Code Tables................................... 6-20
CHAPTER 7
AT COMMANDS AND REGISTERS
7.1 The Command Set ...................................................................... 7-1
7.1.1 Entering Commands....................................................... 7-1
7.1.1.1 Issuing AT Commands at any Speed............. 7-2
7.2 Commands .................................................................................. 7-2
7.2.1 Operating Mode Dial Modifiers ....................................... 7-9
7.3 Registers ................................................................................... 7-41
7.3.1 Commands to Change or Read Registers.................... 7-41
CSMIM-T1 Hardware Installation Guide
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
APPENDIX A
PORT PIN/SIGNAL ALLOCATIONS
A.1 General ....................................................................................... A-1
A.2 Console Port ............................................................................... A-1
A.3 Interface Ports............................................................................. A-2
A.4 Additional Cabletron Cables and Connectors............................. A-3
xii
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
INTRODUCTION
1.1
GENERAL
Welcome to the Cabletron Systems’ CSMIM-T1 Hardware Installation
Guide. This guide provides procedures for the installation of the
CSMIM-T1 into the Cabletron Systems Multi Media Access Center
(MMAC), as well as information on configuring your communications
server to load its operational software. Please read through this manual to
familiarize yourself with the content and to gain an understanding of the
features of the product.
This manual assumes that you have some understanding of networking,
remote access, T1, and telephony technology.
Please note that this manual covers installation and initial configuration
instructions only. Software instructions are provided in the document set
provided with the software package.
This guide provides instructions for installation and testing of the
CSMIM-T1. ROM monitor commands, troubleshooting and diagnostic
procedures are also provided.
1.2
ORGANIZATION OF THIS DOCUMENT
•
Chapter 1, Introduction, describes the hardware features and
firmware functions.
•
•
Chapter 2, Installing the CSMIM-T1, provides installation, power
up, and booting procedures.
Chapter 3, ROM Monitor Commands, describes the ROM Monitor
commands that modify specific configuration parameters, perform
diagnostic tests, and load the operational code.
•
Chapter 4, CSMIM-T1 Parameters, provides T1-specific commands
and parameters.
CSMIM-T1 Hardware Installation Guide
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: INTRODUCTION
•
Chapter 5, Troubleshooting Procedures, provides Troubleshooting
and diagnostic information.
•
•
Chapter 6, Modem Guide, describes modem features and setup.
Chapter 7, AT Commands and Registers, provides a listing of
modem commands and parameters.
•
AppendixA, Port/Pin SignalAllocations, details the CSMIM-T1 port
pinouts, and cabling information.
1.3
DOCUMENT CONVENTIONS
The following conventions are used throughout this document:
Note symbol. Calls the reader’s attention to any item of
information that may be of special importance.
NOTE
Caution symbol. Contains information essential to avoid
damage to the equipment.
!
CAUTION
Electrical Hazard Warning symbol. Warns against an action
that could result in personal injury or death due to an electrical
hazard.
1-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Help
1.4
GETTING HELP
If you need additional support related to this device, or if you have any
questions, comments, or suggestions concerning this manual, contact
Cabletron Systems Technical Support:
Phone
(603) 332-9400
Monday – Friday; 8 A.M. – 8 P.M. Eastern Time
GO CTRON from any ! prompt
ctron.com (134.141.197.25)
anonymous
CompuServe
Internet mail
FTP
Login
Password
your email address
BBS
(603) 335-3358
Modem setting 8N1: 8 data bits, 1 stop bit, No parity
For additional information about Cabletron Systems products, visit our
World Wide Web site: http://www.cabletron.com/
Before calling Cabletron Systems Technical Support, have the following
information ready:
•
•
A description of the failure
A description of any action(s) already taken to resolve the problem
(e.g., changing mode switches, rebooting the unit, etc.)
•
•
•
A description of your network environment (layout, cable type, etc.)
Network load and frame size at the time of trouble (if known)
The serial and revision numbers of all Cabletron Systems products in
the network
•
•
The device history (i.e., have you returned the device before, is this a
recurring problem, etc.)
Any previous Return Material Authorization (RMA) numbers
CSMIM-T1 Hardware Installation Guide
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: INTRODUCTION
1.5
CSMIM-T1 OVERVIEW
The CSMIM-T1 is a dual-slot, Annex Software compatible system
designed to reside in the MMAC series of hubs. The module takes the
existing CSMIM2 core and adds enhanced processing power in the form
of dual 486SXLC2-40 clock doubled processors. Both the main and
secondary processors have been upgraded, which allows the main
processor to control the MMAC network interfaces, while the second
controls the serial ports. These processors have access to a minimum of
4 MB DRAM (standard), but may be upgraded to 8 MB through the
installation of SIMM modules. This memory is shared between the
processors, and arbitrated on a cycle by cycle basis.
Extensive power up diagnostics are provided to confidence check the
system prior to the loading of application software. A Console Port is
used for system setup, booting, and diagnostic purposes. After booting,
the Console Port is idle. System boot is accomplished either from a UNIX
host, a VAX VMS host, or an optional Flash PROM. If you are operating
from Flash only, be aware that host based services such as security are not
supported. If you have any questions, contact Cabletron Technical
Support.
It should be mentioned that although the CSMIM-T1 is capable of
running in a Novell environment, it will not boot from a Novell server. In
a Novell environment, the module must be booted either from a UNIX
server, or from Flash.
There are 24 V.34 modems in the CSMIM-T1. Access for the T-1 network
is provided by a single RJ48C connector on the front panel. Data received
from the T-1 network is either moved through the CSMIM-T1 module and
onto the Ethernet backplane, or fed back out through the Drop and Insert
Interface on the front panel. An example of this would be connecting the
Drop and Insert Interface to a PBX for voice applications.
1-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CSMIM-T1 Front Panel
1.5.1
Software Information
The CSMIM-T1 is shipped to our customers with software that provides
network access to the following networks:
•
•
•
Novell Netware (IPX)
UNIX (TCP/IP)
Macintosh (AppleTalk)
Refer to the software document set for a description of the supported
software features.
In addition to the standard software package, the CSMIM-T1 software
distribution includes a number of T-1 specific commands and parameters
that are used for configuration and administration. Refer to Chapter 4,
CSMIM-T1 Parameters for a description.
1.6
CSMIM-T1 FRONT PANEL
The CSMIM-T1 LED indicators provide the user with feedback on
system activity. Each port connector has an associated LED to indicate
activity on the receive data line. Several other LEDs indicate network
activity, port and connection status, modem status, and diagnostic
information. Refer to Figure 1-1.
CSMIM-T1 Hardware Installation Guide
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: INTRODUCTION
CSMIM-T1
SN
1-8
17-24
STAT
S/U
MODEM
CONFIG
STATUS
9-16
ATTN TRAF
CD TX RX
A
B
C
1
2
3
4
5
SET UP
6
7
8
9
10
11
12
13
CONSOLE
MODEM
PORT
STATUS
14
15
16
17
18
19
20
21
22
23
24
TEST
LOS
BLU
SYNC
NETWORK
STATUS/
ALARMS
RED
YEL
ON LINE
T1 NETWORK
INTERFACE
DROP/INSERT
INTERFACE
DI SYNC
ETHERNET
Figure 1-1 CSMIM-T1 Front Panel
1.6.1
Console Port
The Console Port is used for system setup and diagnostic purposes only.
A single RJ45 connector is used to connect a VT terminal and access the
command set. After booting, the console port is inactive.
1-6
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CSMIM-T1 Front Panel
1.6.2
System LED Indicators
There are 7 indicators to show system activity and status.
ATTN
The amber Attention LED is on when the module requires operator
attention, and flashes when a problem is detected.
STAT
The green Status LED is ON after the module passes the core power-up
diagnostics. This LED also flashes while the module is in a reset state.
TRAF
The green Traffic LED flashes when the module successfully transmits or
receives data over the MMAC Ethernet backplane channel.
S/U
When the green SET UP LED is ON steady, the module is in the SET UP
mode and the user can input configuration data via the console port prior
to booting the operational software.
When the module is in the RESET mode (press and hold the SET UP
button for 3 seconds) the green LED will flash while the CSMIM-T1
executes power up diagnostics.
Ethernet Channel Indicators
There are three green LEDs that indicate the Ethernet channel
(A, B, or C) that is selected by either the software or by jumper
configuration.
1.6.3
The SET UP Switch
The SET UP Switch allows the user to change the operational mode of the
module from normal to set up. When the module powers up, it
automatically enters the normal mode. To enter the SET UP mode, the
SET UP switch must be depressed within 30 seconds of power-up. When
the S/U LED lights, the unit is in the SET UP mode.
Depressing the SET UP Switch at any time for approximately three
seconds causes the module to enter a RESET state. This is the equivalent
of a reboot. The green S/U LED will flash while the unit executes power
up diagnostics, and the SET UP mode can be entered.
CSMIM-T1 Hardware Installation Guide
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: INTRODUCTION
1.6.4
T-1 Network Access
There are two ports on the front panel that allow access to the T-1
network. The T-1 Network Interface Port is an 8-pin, RJ48C port that
provides access for the digital T-1 line. The Drop/Insert Interface is also
an 8-pin, RJ48C port, and provides connection to a local Private Branch
Exchange (PBX), or other equipment, such as an ETWMIM equipped
with a T-1 interface.
In addition to these ports, there are 8 Status LEDs that provide the user
with valuable information regarding the T-1 network.
DI SYNC
The green DI SYNC LED is ON when the T-1 engine is detecting frame
synchronization on the Drop and Insert Interface. The LED is off when
there is a Loss of Frame (LOF) synchronization.
An LOF condition causes the T-1 engine to transmit all unframed ones
(keep alive signal) to the device attached to the Drop and Insert Interface.
ON LINE LED
The green ON LINE LED is ON when the T-1 engine is connected to the
network interface.
1.6.5
NETWORK STATUS / ALARMS
TEST - Network Test
This red indicator is ON when the T-1 engine network interface is placed
into a test loopback condition. Loopback tests are activated either locally
by the user, or by the telco provider.
SYNC - Synchronized
This green indicator is ON when the T-1 engine is properly synchronized
with the network signal and is receiving proper framing information.
LOS - Loss of Signal
This red indicator is ON when the T-1 engine is detecting no signal
(pulses) on the network interface receiver. When a LOS condition exists
the T-1 engine transmits unframed all ones (Alarm Indication Signal) to
the network.
1-8
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CSMIM-T1 Front Panel
RED - Red Alarm
This red indicator is ON during a locally detected carrier failure. During
the “red” alarm condition, a “yellow” alarm is transmitted to the
telephone network.
YEL -Yellow Alarm
This yellow indicator is ON when receiving a “yellow” alarm condition
from the telephone network.
BLU - Blue Alarm
This blue indicator is ON when receiving an unframed, all ones Alarm
Indication Signal (AIS) from the network. This condition exists upon a
loss of originating signal, or when any action is taken that would cause
signal disruption.
1.6.6
Modem Configuration Status LEDs
To help determine if a problem exists in a modem, there are three
green/amber LEDs labeled 1-8, 9-16, and 17-24. These LEDs indicate
groups of modems installed. When amber, the LED indicates that at least
one modem within the indicated group is in a fault condition. When
green, the LED indicates that diagnostics have determined that the
modems are operating normally.
1.6.7
Modem Port Status LEDs
Each modem has a group of three LEDs to indicate activity. These LEDs
can help determine a fault within a group of modems.
CD - Carrier Detect
This green LED is ON when the carrier has been detected on the
telephone line of the corresponding modem. There are a total of 24 CD
indicators, one per channel.
TX - Transmit Data
This green LED flashes to indicate the corresponding modem is
transmitting data. There are a total of 24 TX indicators, one per channel.
RX - Receive Data
This green LED flashes to indicate the corresponding modem is receiving
data. There are a total of 24 RX indicators, one per channel.
CSMIM-T1 Hardware Installation Guide
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: INTRODUCTION
1.6.8
EFS Key Number
The sticker on the front panel next to the serial number is the EFS Key.
This key is factory loaded and enables all options on the module. The EFS
value is stored in the EEPROM, and will be erased when executing the
“erase” command. It is important that you record this value, in the event
you need to clear the EEPROM. To re-enter the key value, refer to the
procedure in Chapter 2, section 2.7.3.
1.7
CONNECTIVITY
Ethernet Interface Selection
The CSMIM-T1 has a 48 pin DIN connector for connection to the A
Channel Ethernet segment, and a 96 pin DIN connector for B and C
channel attachment. Segment selection is performed by setting jumpers,
but may be overridden by commands from the MMAC management
module.
Jumper position and channel selection is explained in Chapter 2,
Installing the CSMIM-T1.
1.8
TELCO CONNECTION INFORMATION
There are different ways the CSMIM-T1 can be set up. It can use either a
full T-1 line, or a fractional one. In either case, there is specific
information the user needs to get from and provide to the Telco providing
the connection. This section supplies some of the basic information
necessary to set up a T-1 connection.
1.8.1
Connecting the CSMIM-T1 to a Full T-1 Line
In a full T-1 application, all channels of the line are used in the same
manner, such as data lines for multiple computer ports. There is no
peeling off of any channels, and the Drop and Insert Port is not used.
Table 1-1 provides a short list of information necessary to configure a full
T-1 circuit in a Point-to-Point Protocol (PPP) environment.
Configurations may vary depending on the application.
1-10
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Telco Connection Information
Table 1-1 Telco Configuration Information
Configuration Information
Supplied by
Service Provider
Configuration Information
Required by User
Line Coding
Frame Type
Clock Source
B8ZS or AMI
ESF or D4
Loop Timing or Local Timing
1.8.2
Connecting the CSMIM-T1 to a FractionalT-1 Line
In a fractional T-1 setup, only a portion of the 24 timeslots or DS-0’s are
used. Some may be routed through the Drop and Insert Port to a PBX, as
in a voice application. Table 1-2 provides a short list of information
necessary to use a fractional T-1 circuit in a PPP environment.
Configurations may vary depending on the hub. The line configuration
information shown in Table 1-2 must be supplied by the service provider.
Table 1-2 Telco Configuration Information
Configuration Information
Configuration Information
Supplied by
Required by User
Service Provider
Line Coding
Frame Type
Clock Source
B8ZS or AMI
ESF or D4
Loop Timing or Local Timing
Timeslots being used for each
end of the circuit
DS-0’s (Timeslots)
For more instructions on the T-1 setup, please refer to the Annex Network
Administrator’s Guide for the CSMIM-T1.
CSMIM-T1 Hardware Installation Guide
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: INTRODUCTION
1.9
COMPATIBILITY
The modems used in the CSMIM-T1 have the following features:
•
Data modem throughput to 115.2 Kbps
-V.34 compatibility
-V.32 bis, V.32, V.22bis, V.22A/B, V.23 and V.22
-Bell 212A and 103
-V.42 LAPM and MNP 2-4 error correction
-V.42bis and MNP 5 data compression
MNP 10 data throughput enhancement (to 14.4 Kbps)
Communication software compatible AT command set
Built-in TTL serial interface (DTE) to 115.2 Kbps
Line quality monitoring and retrain
NVRAM directory and stored profiles
Flow control and speed buffering
•
•
•
•
•
•
•
•
•
•
Automatic line speed selection in V.FC and V.32bis/V.32
Auto dial and auto answer
Tone, pulse, and adaptive dialing
Diagnostics
1.10 CSMIM-T1 PHYSICAL / STATISTICAL
INFORMATION
Dimensions
Height:
Width:
Depth:
11.5 in. (25.4 cm)
4 in. (10 cm)
14.65 in. (34 cm)
1-12
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CSMIM-T1 Physical / Statistical Information
Weight:
4.75 lbs (2.16 kg)
Power: (per slot)
+5VDC @ 9.0 A
+12VDC @ 300 mA
-9VDC @ 1.9 A
-5VDC@ 300 mA
Environment
Operating:
+5° to +40°C (41° to 104°F)
5% to 90% RH, noncondensing
Non-operating:
-30° to 73°C (-22° to 164° F)
Approvals
Safety:
This equipment meets the safety requirements of
UL 1950, CSA C22.2 No. 950, EN60950, IEC 950,
and 73/23/EEC.
Electromagnetic Compatability:
This equipment meets the requirements of FCC Part
15, EN 55022, VCCI V-3/93.01, CSA C108.8, EN
50082-1, and 89/336/EEC.
Telecom:
FCC Part 68, Industry Canada CS-02/CS-03
CSMIM-T1 Hardware Installation Guide
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: INTRODUCTION
1-14
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
INSTALLING THE CSMIM-T1
2.1
GENERAL
This chapter details the installation and set up procedures for the
CSMIM-T1.
The CSMIM-T1 is sensitive to static discharge. Follow static
safety handling rules and properly wear an antistatic wrist
!
CAUTION
strap.
Installing the CSMIM-T1 involves setting jumpers to select an Ethernet
channel, the installation of the CSMIM-T1 into the MMAC chassis,
connecting devices, performing power-up and testing, installing
operational software, and booting procedures. To configure the
CSMIM-T1, you will need a cable and connector pinned out as shown in
Appendix A for the Console Port, and an ASCII terminal or terminal
emulation software.
CSMIM-T1 Hardware Installation Guide
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: INSTALLING THE CSMIM-T1
2.2
LOCATING THE ETHERNET JUMPERS
The CSMIM-T1 has a single jumper block that contains two Ethernet
jumpers and one Subnet jumper. Figure 2-1 shows the locations and
jumper numbers for the Ethernet and Subnet jumpers. Please note that the
jumpers are located on the Main Processor Board, not the modem board.
Ethernet Jumper J12
FUSE
1 2 3
A
J12
B
C
ETHERNET JUMPER SETTINGS
1 2 3
1 2 3
1 2 3
A
B
C
A
B
C
A
B
C
Jumper Settings for
operating on Ethernet A
Jumper Settings for
operating on Ethernet B
(factory setting)
Jumper Settings for
operating on Ethernet C
SUBNET JUMPER SETTINGS
1 2 3
A
B
C
1 2 3
A
B
C
Sub-Net
(Channels B and C)
Full Segment
(Normal Setting)
Figure 2-1 CSMIM-T1 Jumper Settings
2-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating the Ethernet Jumpers
2.2.1
Setting the Ethernet Jumpers
The Ethernet jumpers determine how your CSMIM-T1 operates on the
network. You can set the jumpers so that the CSMIM-T1 operates on
channel A, B, or C. Refer to Figure 2-1 to locate and configure the
jumpers.
There is a single jumper block, labelled J12, that is used to select both the
Ethernet Segment and the Subnet. Pin row A at J12 is used to select the
Subnet. Pin rows B and C are used to select Ethernet Channels. Please use
care in configuring the jumpers. Figure 2-1 shows the default settings
(Channel B) for the CSMIM-T1.
•
To operate on Channel A: Place jumpers over the center pin and pin 3
in pin rows B and C.
•
To operate on Channel B: Place one jumper over the center pin and pin
3 in pin row B, and the other jumper over the center pin and pin 1 in
pin row C.
•
To operate on Channel C: Place one jumper over the center pin and pin
1 in pin row B, and the other jumper over the center pin and pin 3 in
pin row C.
2.2.2
Setting the Subnet Jumper
The CSMIM-T1 allows grouping of the B and C channels into a subnet to
provide additional Ethernet networks. All MIMs in the MMAC to the left
of the CSMIM-T1 become isolated on the B and C channel FNB
connector. These additional networks cannot communicate over the B and
C channel FNB connector with any module to the right.
Ethernet Channel and Subnet jumper settings can be
overridden by an EMME or EMM-E6 installed in the MMAC.
NOTE
CSMIM-T1 Hardware Installation Guide
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: INSTALLING THE CSMIM-T1
To set the Subnet jumper, refer to Figure 2-1 and configure pin row A of
J12 as follows:
•
Normal Operation (maintain continuity of the backplane: Default):
Place a jumper over the center pin and pin 3 in pin row A.
•
Subnet mode: Place a jumper over the center pin and pin 1 in pin rowA.
2.3
NETWORK BYPASS JUMPER
The CSMIM-T1 has an internal jumper that is used to select a bypass
mode for the T-1 Engine. The T-1 engine will go into a bypass mode when
the MMAC hub is powered down, reset, or when the CSMIM-T1 module
is removed from the hub. This jumper is labelled J24, and is located on the
modem board, just behind the T-1 Network Interface port (See Figure
2-2).
Front of Module
Top
1 2 3
Loopback Mode: Jumper
over pins 2 and 3
1 2 3
J24
Bypass Mode: Jumper
over pins 1 and 2
Figure 2-2 Network Bypass Jumper
The jumper can be set to Network Loopback Mode (default setting) or
Bypass Mode. Please check your module to see that the jumper is
configured in the default setting before installing into your hub.
Network Loopback Mode loops back all signals on each interface.
The Bypass Mode will connect the DSX1 lines directly to the DS1 lines.
2-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the CSMIM-T1
Using Bypass Mode will allow a connection to the network to be
maintained even though the system is powered down (or not on-line). If
all channels are not being used for modem applications, the DSX1
interface could be used to drop-and-insert the PBX voice channels into
the DS1 connection. (In this example, it requires that the PBX have an
integral T1-CSU to terminate the network.)
In addition to J12 and J24, there are other jumpers on the
module. These are used for diagnostic purposes, or are factory
presets. Changing any of the jumper positions could cause
damage to your module.
!
CAUTION
2.4
INSTALLING THE CSMIM-T1
Installation should be performed by qualified personnel only.
!
CAUTION
The CSMIM-T1 is sensitive to static discharge. Follow static
safety handling rules and properly wear an antistatic wrist
strap.
!
CAUTION
When installing the CSMIM-T1, keep the following in mind:
•
You may install the CSMIM-T1 in any slot except for slot 1 (farthest
slot to the right) of the MMAC chassis.
•
We suggest positioning the CSMIM-T1 next to any contiguous RIC
MIMs or MIMs directly controlled by the hub managing device (e.g.,
EMME, EMM-E6, etc.). This does not apply to shunting
MMAC-FNBs, where the data path remains unbroken, and allows
non-interrupted communication.
Although Cabletron Systems modules have “hot swap”
capabilities, we recommend that you power down the MMAC
hub prior to installation.
NOTE
Install the CSMIM-T1 into the MMAC-FNB (backplane) as follows:
CSMIM-T1 Hardware Installation Guide
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: INSTALLING THE CSMIM-T1
1. Remove Security Bars from MMAC chassis, and blank plates from
desired slots.
2. Holding the CSMIM-T1 by the front panel, or by the edges of the
board, align the bottom and top edges of the board with the guide slots.
Make sure that both of the edges of the card rest in the guide slots.
3. Slide the CSMIM-T1 (Figure 2-2) into the desired MMAC slots.
4. Firmly press the module connections into the backplane. Do not try to
force the module into place or use the knurled knobs to draw the
module into the backplane. Forcing a misaligned module into place
can damage the CSMIM-T1 or the MMAC backplane.
5. Secure the module to the MMAC chassis by tightening the knurled
knobs. If you do not tighten the knurled knobs, vibration can cause the
module to lose contact with the backplane and disrupt your network.
6. Replace Security Bars on MMAC chassis.
7. Power-up the MMAC.
Knurled Knob
MMAC M8FNB
CSMIM-T1
CSMIM-T1
SN
1-8
17-24
STAT S/U
ATTN TRAF
MODEM
CONFIG
STATUS
9-16
CD TX RX
A
B
C
1
2
3
4
5
SET UP
6
7
8
9
10
CONSOLE
MODEM
PORT
STATUS
11
12
13
14
15
16
17
18
19
20
21
22
23
24
TEST
LOS
BLU
SYNC
NETWORK
STATUS/
ALARMS
RED
YEL
ON LINE
T1 NETWORK
INTERFACE
DROP/INSERT
INTERFACE
DI SYNC
ETHERNET
Figure 2-3 Installing the CSMIM-T1
2-6
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Making Connections
2.5
MAKING CONNECTIONS
This section describes how to connect the CSMIM-T1 to a console to
access the boot commands, and connecting the T-1 interface as well as the
Drop and Insert connection.
Table 2-1 Maximum Recommended Cable Lengths
Line Speed
Cable Length (Feet)
Allowed Loss
T-1 Long Haul
D&I Short Haul
57.6 kbps
6000
655
100
50
36dB@772 khz
3dB@772 kHz
30
15
115.2 kbps
If you exceed these recommended cable lengths, you must
compensate for any resulting problems by reducing the baud
rate, using low capacitance cable, etc. Exceed these distances
at your own risk.
NOTE
2.5.1
Connecting a Console Terminal
In order to access the ROM Monitor and boot the CSMIM-T1 for the first
time, you will need to connect a terminal to the Console Port. Please use
the adapters supplied in the accessory kit shipped with the module, as the
CSMIM-T1 Console port is a different configuration than other Console
ports. Follow the steps in this section to connect a console terminal to the
console port located on the front panel of the CSMIM-T1.
1. Connect the Console Terminal’s I/O connector to the RJ45 cable (the
accessory kit includes a cable) using a DB-25 DTE drop adapter.
2. Plug the RJ45 connector into the console port located on the front
panel of the CSMIM-T1.
3. When the connector clicks into place, the connection is secure.
Appendix A describes the console port’s signal/pin allocation.
4. Turn on the Console Terminal and set the terminal to 9600 baud, eight
data bits, no parity, one stop bit, and XON/XOFF flow control.
The ROM Monitor assumes that this terminal is CRT-based and displays
the backspace (BS) character accordingly.
CSMIM-T1 Hardware Installation Guide
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: INSTALLING THE CSMIM-T1
To put the CSMIM-T1 into ROM Monitor mode, press the SET UP button
within 30 seconds of powering up. You can also reset and set up the
CSMIM-T1 by pressing the SET UP button until the TRAF LED comes
ON, release the button and then press it again. This will reboot the
module, and it will come up into ROM Monitor mode.
The CSMIM-T1 takes approximately 3 minutes to boot in the
ROM Monitor mode, depending on network traffic.
NOTES
During the boot process, the TEST LED remains on.
The red ATTN light is ON when the unit is in ROM Monitor
state.
2.5.2
Connecting a T1 Network Interface
The T1 Network Interface is used to connect the CSMIM-T1 to the T1
line. The T1 Network Interface port is located on the front panel of the
CSMIM-T1.
To connect to the T-1 network, simply plug the RJ48C connector located
on the T1 Network Interface Cable into the T1 Network Interface port
located on the front panel of the CSMIM-T1.
When the connector clicks into place, the connection is secure. Appendix
A describes the T1 Network Interface port’s signal/pin allocation.
2-8
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Power-up and Test
2.5.3
Connecting a Drop/Insert Interface
The Drop/Insert Interface is used to connect various CSMIM-T1 channels
to a local PBX or other equipment. The Drop/Insert Interface port is
located on the front panel of the CSMIM-T1.
To connect your local equipment to the CSMIM-T1, simply plug the
RJ48C connector located on the Drop/Insert Interface Cable into the
Drop/Insert Interface port located on the front panel of the CSMIM-T1.
When the connector clicks into place, the connection is secure. Appendix
A describes the Drop/Insert Interface port’s signal/pin allocation.
The CSMIM-T1 can incur damage if the cables conduct
transients such as those induced by lightning strikes, etc.
!
CAUTION
2.6
POWER-UP AND TEST
1. Apply power (or insert into MMAC). The CSMIM-T1 now runs its
ROM-resident power-up diagnostics. The indicators momentarily
light and then turn off, except for the ON LINE LED and some status
LEDs.
If the diagnostics complete successfully, the CSMIM-T1 either enters
SET UP Mode and waits for configuration data to be entered, or boots
its operational image from Flash.
You can enter configuration information through a terminal
connected to the console port. The ROM monitor prompt (monitor::)
appears on the terminal.
If the ATTN and the STAT LEDs are flashing together, there is a
CSMIM-T1 hardware failure. Contact Technical Support.
If the ATTN LED is flashing, there is a network or network interface
failure. An error message will display on the console.
If a network or network interface failure occurs, typing q accesses the
ROM Monitor prompt. Check the network connection, and then see
the net command in Chapter 3.
See Chapter 5 for additional troubleshooting information.
2. Verify the CSMIM-T1 hardware configuration.
CSMIM-T1 Hardware Installation Guide
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: INSTALLING THE CSMIM-T1
At the monitor prompt on the console, type config and press the
Return key. The following appears on the screen:
REVISION/CONFIGURATION INFORMATION
ROM Software Rev: 0914
Board ID: 42
Board Type: CSMIM-T1
Ethernet Address: 00-80-2D-00-18-B6
EEPROM size: 65504
CPU Type: 486SXLC2
Memory size: 4 Meg
Flash size: N/A
Flash ID: N/A
T1 Unit Identification: XYLOGICS T1-ENGINE 085234 Rev. A 07/19/95 6343
T1 Network Jumper: Cross Connect Mode
DS0: B8ZS Coding
DSX: B8ZS Coding
ESF Framing
ESF Framing
AT&T FDL Format
Line Distance=535 to 635 Feet
Port #
T1 Slot Map
Mod ID
1
N
2
N
3
N
4
N
5
N
6
N
..... 11
..... N
12
N
288X 288X 288X 288X 288X 288X ..... 288X 288X
Mod Status
OK
OK
OK
OK
OK
OK
..... OK
OK
Port #
T1 Slot Map
Mod ID
13
N
14
N
15
N
16
N
17
N
18
N
..... 23
..... N
24
N
288X 288X 288X 288X 288X 288X ..... 288X 288X
OK OK OK OK OK OK ..... OK OK
Mod Status
To record the CSMIM-T1’s Ethernet address for future reference: at the
monitor prompt, type addr -d and press the Return key. The display
looks like this:
monitor:: addr -d
Ethernet address (hex): 00-80-2D-00-18-B6
Internet address: <uninitialized>
Subnet mask: 255.0.0.0
Broadcast address: 0.0.0.0
Preferred load host address: <any host>
Preferred dump address: 0.0.0.0
Load/Dump Gateway address: <uninitialized>
Type of IP packet encapsulation: <ethernet>
Load broadcast: Y
You are prompted for the gateway address only if the Internet
address differs from the preferred Load Host address based on
NOTE
the Subnet Mask. If these addresses are the same, the
CSMIM-T1 assumes there is no gateway.
2-10
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto-initializing the ROMs
2.7
AUTO-INITIALIZING THE ROMS
The CSMIM-T1 is distributed without an IP address or preferred load
host (UNIX/IP or MOP) defined in ROM. When the device is booted, the
CSMIM-T1 attempts to auto-initialize its ROMs using BOOTP (bootstrap
protocol) and RARP (Reverse Address Resolution Protocol).
The CSMIM-T1 supports the BOOTP and RARP protocols. The ROMs
use these protocols to obtain boot information without requiring any
manual set up on the CSMIM-T1.
•
BOOTP is a bootstrap protocol that allows a diskless client to
determine its Internet address, the Internet address of the server, and
the name of the file to be loaded into memory.
•
RARP (Reverse Address Resolution Protocol) maps a hardware
address into an Internet address.
The ROM invokes these methods of acquiring boot information when a
boot is initiated and the CSMIM-T1’s Internet Address is not initialized.
Under this condition, the CSMIM-T1 first tries to get boot information via
BOOTP; if BOOTP fails, it tries to get boot information via RARP. If
neither protocol is successful, the CSMIM-T1 attempts to load an image
by transmitting an IPX advertisement request for service and a MOP
multicast boot request. Although it will attempt to load an IPX image, the
module WILL NOT BOOT FROM IPX.
If all requests fail, the CSMIM-T1 will return to the ROM Monitor (if in
test mode) or continue the auto initializing procedure indefinitely (if in
normal mode).
CSMIM-T1 Hardware Installation Guide
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: INSTALLING THE CSMIM-T1
2.7.1
BOOTP
For a successful BOOTP retrieval, a bootpd must be running on a host on
the same network as the CSMIM-T1 and must have the appropriate
information in the bootptab file. The CSMIM-T1’s BOOTP
implementation adheres to rfc 951, rfc1048, and rfc1084. Below is a
sample bootptab file entry used to initialize the CSMIM-T1 named
terminator.
csmimt1default:\
:sm=255.255.255.0:gw=132.245.22.66:\
:hn:vm=auto:to=-18000:
terminator:
ht=1:ha=00802d004879:ip=132.245.22.226:
tc=remoteannexdefault:
In the previous example:
•
•
•
•
•
•
sm is the subnet mask
gw is the load/ dump gateway address.
vm is the Vendor Magic Cookie
ht is host type (1=Ethernet)
ha is the CSMIM-T1’s hardware address (Ethernet Address)
ip is the CSMIM-T1’s Internet Protocol Address
When the CSMIM-T1 receives a BOOTP response with the sm, gw, and
ip set, it sets the respective parameters: subnet_mask,
load_dump_gateway, and inet_addr. Set vm to auto. This indicates that
bootpd should respond to the client (CSMIM-T1 in this case) with
whatever format the client requests; the CSMIM-T1 (client) always
requests in the decimal dot notation format (99.130.83.99). The bootpd
adds the address of the host on which it is running as the Server Address
in the bootp response message. The ROMs use the Server Address as the
preferred load host and store it in the pref_load_addr parameter.
The bootpd must be running on the CSMIM-T1’s preferred
load host.
NOTE
2-12
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Installation Procedures
2.7.2
RARP
If the CSMIM-T1 does not receive a successful BOOTP response, it uses
RARP to get the boot information. For a successful RARP retrieval,
TCP/IP must be running on a host that is on the same network as the
CSMIM-T1 and the host’s ARP table must be initialized with the
CSMIM-T1’s Internet and Ethernet addresses (see the arp man page,
arp -s).
The only boot information that RARP provides is the CSMIM-T1’s
Internet address. The ROMs save this information in the inet_addr
parameter. The ROMs use default information for the Subnet Mask and
preferred load host. This means the ROMs will broadcast their request.
The host serving the CSMIM-T1 its boot information must be running on
the same network because the CSMIM-T1 only broadcasts BOOTP and
RARP queries.
If BOOTP and RARP fail, the CSMIM-T1 transmits an IPX
advertisement Request for Service and a MOP Multicast boot request.
If all requests fail, the CSMIM-T1 returns to the ROM monitor (if in test
mode) or continues the auto initializing procedure indefinitely (if in
normal mode).
2.8
SOFTWARE INSTALLATION PROCEDURES
Install the operational code on a UNIX host before loading it on a
CSMIM-T1. Please note that although the CSMIM-T1 will run on a
Novell system, it will not boot from Novell. The UNIX Installation Notes
describe how to install software on a UNIX host, as well as a non-UNIX
host. The CSMIM-T1 may also be booted from software loaded on
another CSMIM-T1 containing Flash, or from its own Flash memory (see
Section 2.7.2, Self Booting the CSMIM-T1).
When loading the CSMIM-T1 software for the first time, use the ROM
Monitor commands.
CSMIM-T1 Hardware Installation Guide
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: INSTALLING THE CSMIM-T1
If you are loading software for the first time on a new unit, it is
not necessary to erase the EEPROM. To do so will erase the
EFS Key information, and you will have to reload it manually. If
you have not recorded the key information and erase the
EEPROM, you will have to call Cabletron Customer Service
with your PO number to get a new one. For the reloading
procedure, see Section 2.7.3 Reloading the EFS Key.
!
CAUTION
The erase command will also delete the LAT key, which is
obtained separately from the EFS Key. Please make sure you
have stored these keys in a safe place.
At the monitor prompt,
1. If necessary, execute the erase command to clear the EEPROM. (See
the erase command in Chapter 3.)
2. Execute the addr command to enter CSMIM-T1 operating parameters
described in Section 3.2, such as IP address, Ethernet address, Subnet
Mask, Broadcast address, Preferred Load Host and Dump Host.
3. Execute the boot command (see the boot command in Chapter 3).
The CSMIM-T1 takes 4 to 5 minutes for a normal boot over the
network, depending on traffic.
NOTE
If the boot is successful, then the following LED’s will be on:
•
•
•
•
Modem Config LED’s (Green)
STAT LED (Green)
Ethernet Channel Indicator LED (Green)
ON LINE LED (if T-1 line is connected)
If the boot is unsuccessful, the red ATTN LED will flash, and a message
will display on the monitor.
2-14
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Installation Procedures
2.8.1
Invoking the Console Monitor
After the image boots, you can invoke a Console Monitor by pressing the
<Enter> key on the console. At the Console Monitor prompt, entering
help or ? displays the available options:
•
•
•
•
•
•
•
•
dump (from the CSMIM-T1 to the host and reboots).
help or ? (displays the available options).
info (displays configuration information for the CSMIM-T1).
leds (displays the current front panel LED status).
quit (exit the Console Monitor, e.g., quit the console).
reboot filename (reboots the CSMIM-T1).
rom (returns the CSMIM-T1 to the ROM Monitor).
syslog (displays syslog messages).
2.8.2
Self-Booting the CSMIM-T1
After you have installed your optional Flash ROM, the CSMIM-T1 can be
self-booted. You can check your CSMIM-T1 configuration by entering
the config command at the Monitor::prompt. The config command
displays the current configuration information and revision levels. If your
device has Flash ROM installed, the line “FLASH PROM size:” will
appear under the REVISION/CONFIGURATION INFORMATION
section.
This section contains a description of what you need to do to boot your
CSMIM-T1 from FLASH ROM. See Section 3.2 for more information on
the commands referenced here. Proceed as follows:
1. Enter the ROM Monitor mode (see Section 2.4.1 for information on
entering the ROM Monitor mode).
2. Set the Internet address to a valid IP address and the Subnet Mask to a
valid mask using the addr command.
3. Using the sequence command, set the interface sequence to self.
4. Execute the boot command (expect this to take upward of 5 minutes).
CSMIM-T1 Hardware Installation Guide
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: INSTALLING THE CSMIM-T1
2.8.3
Reloading EFS Key Value
In the event that the EFS value is lost, follow this procedure to reload the
key. This requires Superuser privileges. If you do not have the correct
access abilities, contact the Network Administrator for assistance. If you
have not stored the key value in a safe place and must contact Cabletron
Customer Support, do so before beginning this procedure.
1. Telnet to the module.
2. At the annex:prompt, run the stats -ocommand, to check the status
of the module.
3. Become Superuser. At the annex#prompt, enter show ann opt_key.
This will show the current option key value in quotations.
4. Enter the EFS value at the prompt.
5. Reboot Unit.
6. At the annex:prompt enter stat -ocommand again to check that the
value was accepted.
2-16
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3
ROM MONITOR COMMANDS
3.1
GENERAL
This chapter describes the ROM Monitor commands. These commands
are accessed through a terminal connected to port 1 when the CSMIM-T1
is in SETUP mode. Pressing the SETUP switch within 3 seconds of
powering up puts the CSMIM-T1 into Set Up mode.
The ROM Monitor commands allow you to set a number of EEPROM
parameters. Some of these parameters, like the unit’s Internet address, are
required for booting the CSMIM-T1; some parameters, like the broadcast
address, are required if the network configuration differs from the
supplied defaults. Table 3-1 lists the ROM Monitor commands.
Other parameters, although not required, are recommended for the
CSMIM-T1’s initial boot. Setting these parameters rather than using the
assigned defaults minimizes errors during the initial boot. For example,
setting the parameter that defines the preferred load host enables the
CSMIM-T1 to load by requesting assistance from a specific host rather
than by broadcasting that request to all hosts on the Ethernet.
You can define the same parameters using the Network Administrator
(na) program as you can using the ROM Monitor. ROM Monitor
commands generally provide data about current EEPROM parameters.
When appropriate, they also display a prompt that allows the operator to
change those parameters. Default or current values for parameters are
displayed in brackets. For example:
Enter broadcast address [132.245.6.255]:
At the prompt enter a different value or press the Return key <cr> to
leave the displayed value unchanged.
You can use unique abbreviations for all ROM Monitor commands except
erase. For example, enter boot as bo, and enter net as n. If you enter an
abbreviation that is not unique enough, an error message is displayed on
the console terminal.
CSMIM-T1 Hardware Installation Guide
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
Table 3-1 ROM Monitor Command
Displays and sets EEPROM values relevant to network
addressing, including the CSMIM-T1’s Internet address.
addr [-d]
Manually boots and loads the CSMIM-T1’s operating
code.
boot [-v] [<file>]
boot [-l] [<file>]
config
Erases the existing Flash memory and copies a new
image to Flash.
Displays the current hardware configuration and
revision levels.
console-baud
erase
Changes the console port’s baud rate.
Erases non-volatile memory.
help (or “?”)
Display the list of ROM Monitor commands.
Displays and/or sets the load image and TFTP load
dump names.
image [-d/<file>]
ipx [-d]
Sets IPX load/dump file server.
Sets LAT key.
lat_key [-d]
mop [-d]
Sets MOP load/dump address.
Executes an Ethernet stand-alone external loopback
test.
net
option_key [-d]
ping
Sets or displays the option key.
Sends ICMP ECHO_REQUEST, host [data size]
[npackets].
Shows the current status of all ports and tests specified
port(s).
ports [-d]
sequence
[-d | <list>]
Displays and edits the load/dump interface list.
Configures an SLIP interface.
slip [-d] <port>
Displays current network statistics gathered by the
ROM.
stats [-slip]
3-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
3.2
COMMANDS
Following is an explanation of each of the ROM monitor commands,
syntax and other usage information.
3.2.1
addr
The addr command displays and sets several CSMIM-T1 operating
parameters (EEPROM values) relevant to IP network addressing:
•
•
•
•
•
•
•
•
Internet address.
Subnet mask.
Broadcast address.
Preferred Load Host address.
Preferred Dump Host address.
Load/Dump Gateway address.
Type of IP Packet encapsulation.
Load Broadcast
The addr -d command also displays the unit’s ROM-resident Ethernet
address in hexadecimal notation (see the CSMIM/MicroCS
Administrator’s Guide for UNIX). The command syntax is:
addr [–d]
If you enter the addr command without the –d argument, the console
prompts you for each Internet address. Enter Internet addresses using the
standard decimal dot (.) notation.
The addr –d command displays the CSMIM-T1’s Ethernet address, IP
address, subnet mask, broadcast address, preferred load host address,
preferred dump host address, load/dump gateway address, IP
encapsulation type, and Load Broadcast. The addr -d command cannot
be used to make changes to any of the displayed parameters.
CSMIM-T1 Hardware Installation Guide
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
The addr command display looks like this:
monitor:: addr
Enter Internet address [<uninitialized>]:: 192.9.200.214
Internet address: 192.9.200.214
Enter Subnet mask [255.255.0.0]::
Enter Broadcast address [0.0.0.0]:: 192.9.200.0
Broadcast address: 192.9.200.0
Enter Preferred Load Host address [<any host>]:: 192.9.200.88
Preferred Load Host address: 192.9.200.88
Enter Preferred Dump Host address [0.0.0.0]:: 192.9.200.88
Preferred Dump Host address: 192.9.200.88
Enter Load/Dump Gateway address [<uninitialized>]:: 192.9.200.
Load/Dump Gateway address: 192.9.200.88
Select type of IP packet encapsulation (ieee802/ethernet)
[<ethernet>]::
Load Broadcast Y/N [Y]::
The addr -d command display looks like this:
monitor:: addr -d
Ethernet address (hex): 00-80-2D-00-C6-1E
Internet address: 192.9.200.214
Subnet mask: 255.255.0.0
Broadcast address: 192.9.200.0
Preferred Load Host address: 192.9.200.88
Preferred Dump Host address: 192.9.200.88
Load/Dump Gateway address: 192.9.200.10
Type of IP packet encapsulation: <ethernet>
Load Broadcast: Y
The CSMIM-T1 must have an Internet (IP) address in its memory before
it can load its operational image across the Ethernet via the IP protocol.
Therefore, you must enter the IP address before booting the CSMIM-T1
from a UNIX load host. If you do not define an IP address for the Remote
Annex, it will attempt to learn the address using BOOTP or RARP. If you
3-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
do not define a subnet mask, the CSMIM-T1 uses the generic mask for
the specified IP address.
The Remote Annex tries to boot from a preferred UNIX load host. If you
do not define a preferred load host, the CSMIM-T1 broadcasts its load
request on the subnet and loads software from the first host that responds.
If the part of the IP address containing the network address differs from
the preferred load or dump host, that host must be reached through a
gateway. The addr command prompts you for this gateway’s IP address.
The CSMIM-T1 uses the broadcast address parameter when loading a
file. If this parameter contains a specific address (for example,
132.245.6.255), the CSMIM-T1 uses only that address for broadcast. If
the value is all zeroes (0.0.0.0), the ROM Monitor tries various
combinations of broadcast addresses and subnet or network broadcasts.
The CSMIM-T1 broadcasts its request three times for each possible
combination of broadcast addresses.
You can specify the IP encapsulation type as either ethernet for Ethernet,
or ieee802 for IEEE 802.2/802.3. The default IP encapsulation is
ethernet. Many systems have hardware Ethernet interfaces that are IEEE
802.3 compliant, but very few actually do 802.3 IP packet encapsulation.
Do not change this parameter unless you know absolutely that
your Ethernet does 802.2/802.3 IP packet encapsulation. An
NOTE
incorrect IP encapsulation type prevents your Remote Annex
from booting.
3.2.2
boot
The boot command requests the loading of appropriate CSMIM-T1
operating software from the preferred load host. The command syntax is:
boot [–lv | filename]
CSMIM-T1 Hardware Installation Guide
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
The boot –l command is supported only if the self-boot option
NOTES
(Flash) is installed.
Typing the letter q or CONTROL-C interrupts the boot.
If you try to boot with a non-existent image file name, the
Annex will hang as it searches for the image.You must press
the RESET button to recover.
A successful boot disables the Console and the ROM monitor.
The boot command accepts a file name for the CSMIM-T1’s image. If the
file name is not specified, boot displays the default file name and prompts
for one. If you do not provide a file name, or have not defined one for the
CSMIM-T1, boot requests the default file oper.56.enet. You can also
enter a file name using the image command.
The Remote Annex boots from the defined preferred load host (UNIX/IP,
Novell/IPX, or VAX VMS/MOP). If the preferred load host is not defined
or does not respond, the CSMIM-T1 broadcasts on the Ethernet and loads
from the first host that responds.
To initiate loading, the CSMIM-T1 sends a load request message to the
selected host. After receiving a response, the CSMIM-T1 loads its
operational code to RAM memory. When loading is complete, it transfers
control to the newly-loaded program. The CSMIM-T1 displays a symbol
on the console for each data block received during the boot.
When the CSMIM-T1 begins to boot, it displays the load server host’s IP
address. If the unit does not boot successfully after several attempts, it
displays a boot attempt failed message; if the unit has opened the boot file
and an error occurs during the boot process, it displays a boot error report
on the console and returns to the ROM Monitor. The boot error report can
help determine the cause of the boot failure.
During a boot, the console may display four possible status symbols: “.”
indicates received data blocks, “?” indicates unanswered requests, “*”
indicates transmission errors, and “! ~XXXX~” is a status word from the
Ethernet chip on the Annex indicating a gross problem with the Ethernet
connection (if this symbol appears in your boot command display, contact
technical support).
3-6
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
The status word “! ~XXXX~”, where XXXX are four hexadecimal digits,
decodes as follows:
8000 = Command complete
4000 = Chip is busy
2000 = Command completed without error
1000 = Command aborted by an abort command
800 =
400 =
200 =
100 =
80 =
Late collision detected
Carrier lost
CTS lost
DMA underrun
Transmission deferred because link was busy
Collision detected during interframe spacing
(SQE/Heartbeat detected)
Excessive collisions
40 =
20 =
10 =
Reserved
The lowest nibble (bits 3 to 0) are a count of collisions during this
transmission. For example:
~8802~ = Complete, Late collision, 2 collisions
~8841~ = Complete, Late Collision, SQE detected, 1 collision
The boot command display (using bfs) looks like this:
monitor:: boot
Enter boot file name[(ip) “oper.56.enet”,\
(mop) “OPER_56_ENET.SYS”]::
Requesting default boot file “OPER_56_ENET.SYS” for MOP/VMS\
loads and “oper.56.enet” for all other protocols.
Unanswered requests shown as ‘?’,transmission errors as ‘*’.
Requesting boot from 192.9.200.88 via Ethernet...
Booting BFS file using open delay of 8
Booting BFS file from 192.9.200.88
Header received OK. Received data blocks shown as ‘.’.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. .. . . . . . . . . . . ? . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. * . . . . . . . . . . . . . . . . . . . . . . . . . . . . * .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . ? . . . . . . . . . . . . . . . .
. . . . . . . . . . EOF
CSMIM-T1 Hardware Installation Guide
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
The next example shows a boot using tftp. The CSMIM-T1 always tries
to open a file using bfs first. If unsuccessful, the Remote Annex uses tftp
to open the file.
monitor:: boot
Enter boot file name [(ip) “oper.56.enet”, \
(mop) “OPER_56_ENET.SYS”]::
Requesting default boot file “OPER_56_ENET.SYS” for MOP/VMS\
loads and “oper.56.enet” for all other protocols.
Unanswered requests shown as ‘?’,transmission errors as ‘*’.
Requesting boot from 192.9.200.88 via Ethernet...
Booting BFS file using open delay of 8
?
Booting TFTP file using open delay of 8
Booting TFTP file from 192.9.200.88
Header received OK. Received data blocks shown as ’.’.
.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .. . . . . . . . . . . ? . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . .
. * . . . . . . . . . . . . . . . . . . . ? . . . . . . . . . .
. . . . . . . . . . . . . . . . EOF
The boot –l command downloads and saves the operational image to
non-volatile memory, erases the existing Flash memory, copies the new
image from non-volatile memory to Flash memory, and then executes the
image.
3-8
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
The boot –l command is supported only if the self-boot option
is installed.
NOTE
After executing a boot –l, the ls command may not show the
newly-loaded image.
The boot –l command display looks like this:
monitor:: boot –l
Enter boot file name [(ip) “oper.56.enet”, \
(mop) “OPER_56_ENET.SYS”]::
Requesting default boot file “OPER_56_ENET.SYS” for \
MOP/VMS loads and “oper.56.enet” for all other protocols.\
Unanswered requests shown as ‘?’, transmission errors as\ ‘*’.
Requesting boot from 192.9.200.88 via Ethernet...
Booting BFS file using open delay of 8
Booting from 192.9.200.88
Header received OK. Received data blocks shown as ‘.’.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..
. . . . . . . . . . . . . . . . . . . .EOF
Saving image into storage device ...
Erasing device
|----------------------------|
..............................
Erase completed
Storing image .............
Storage completed
Beginning execution of image...
AnnexCommandLineInterpreter*Copyright1993,1995\Xylogics,
Inc.
annex:
Only use the boot -l command when reloading your Flash
memory (e.g., when upgrading to a new version of software).
NOTE
Make sure that you have a properly configured load host
available or you will erase your image from Flash and will not
be able to load a new one.
CSMIM-T1 Hardware Installation Guide
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
The boot –v command displays the boot in verbose mode. This output
includes the turnaround time in milliseconds for each request. This value
equals the time lapse between sending the request and receiving the
proper reply from the host.
When the boot is complete, verbose output includes a display of network
statistics:
monitor:: boot –v
Enter boot file name [(ip) “oper.56.enet”, \
(mop) “OPER_56_ENET.SYS”]::
Requesting default boot file “OPER_56_ENET.SYS” for MOP/VMS\
loads and “oper.56.enet” for all other protocols.
Unanswered requests shown as ‘?’, transmission errors as ‘*’.
Requesting boot from 192.9.200.88 via Ethernet...
Booting from 192.9.200.88 (42 msec)
Header received OK. Received data blocks shown as msec
turnaround time.
4 4 6 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 4 4 4 4 4
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 4 4 4 4 4 4 4 4 4 4 4 4 4 5 4 4
4 4 4 4 4 6 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 4 4
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 4 24 4 4 6 4 10 4 6
73 4 4 5 4 4 4 4 4 9 4 4 11 4 4 4 4 4 4 4 4 4 4 4 4 4 3 4 4 4 4 4
4 4 6 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 11 6 4 4 4 4
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 4 4 4 4 6 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 4 4
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 EOF
Ethernet Statistics
Frames Received:
CRC Errors:
Alignment Errors: 0
Resource Drops:
Bus Wait Drops:
1031
0
Frames Sent:
1301
0
0
Carrier Sense Losses:
Clear to Send Losses:
Collisions Detected:
9
0
9
Excessive Collision Losses: 0
Bad Types/Lengths: 0
3-10
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
3.2.3
config
The config command displays the CSMIM-T1’s total number of ports,
total amount of memory, the ID number, the serial number, the major and
minor hardware revision numbers, and the ROM software revision
number. The config command display contains information describing
whether or not Flash ROM is installed. The command syntax is:
config
The config command display looks like this:
monitor:: config
REVISION/CONFIGURATION INFORMATION
ROM Software Rev: 0901
Board ID: 56
Board Type: Micro-CS
CPU Type: 486SXLC2
Memory Size: 4 Meg
Flash Size: 2 Meg
EEPROM Size: 32736
Ethernet Address: 00-80-2D-00-C6-1E
Flash ID: 8989
Installed Alternate Interface: ThinNet
ASYNC Config
Number of Ports: 16
Max Port Speed: 115.2 Kbps
CSMIM-T1 Hardware Installation Guide
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
3.2.4
console-baud
The console-baud command changes the console port’s baud rate. Thus,
the console port can interface with any modem to which it is connected.
When the baud rate is entered as auto, the CSMIM-T1 detects the baud
rate of the incoming line and adjusts its baud rate accordingly. This
command provides support for remote troubleshooting. The command
syntax is:
console-baud
The command display looks like this:
monitor:: console-baud
Remote Diagnostic Test Mode
In order to use the remote diagnostic functionality, you
must first connect a modem to the console port of the
Annex. The modem should be configured such that DTR is
forced on, carrier detect and DSR are set normal, and
auto-answer is enabled. Once this is done, contact your
service representative for remote diagnostic maintenance.
To enter “Autobaud Mode”, please type “Auto”. To
“manually” configure the Annex console port, please type
in the desired baud rate. To return to the “monitor::”
prompt strike the “carriage return <CR>” key.
[Baudrate Range: 50-9600 BAUD]
Select Baudrate []::
This command has no effect on the port’s baud rate after the
CSMIM-T1 is booted
NOTE
To provide remote access to the CSMIM-T1 ROMs:
1. From a site local to the CSMIM-T1:
•
Set the CSMIM-T1 into test mode so the monitor prompt appears
on the console.
•
Set the modem into auto-answer mode.
3-12
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
2. From the CSMIM-T1 console port:
•
•
At the monitor prompt, enter console-baud.
At the Select baud rate prompt, enter the appropriate baud rate or
auto.
•
Connect the modem to the CSMIM-T1’s console port.
3. From the remote site:
•
•
Dial into the modem connected to the CSMIM-T1.
Type RETURN until the monitor prompt appears.
3.2.5
erase
The erase command erases the contents of non-volatile memory,
including the CSMIM-T1’s IP address. This command also restores the
parameters to their factory defaults. The syntax is:
erase
If the self-boot option is installed, the erase command prompts for which
non-volatile memory to erase: EEPROM or FLASH. Entering 1 at the
prompt causes the CSMIM-T1 to erase the EEPROM memory
(configuration information); entering 2 at the prompt causes the
CSMIM-T1 to erase the Flash memory (self-boot image).
The erase command display looks like this:
monitor:: erase
1) EEPROM (i.e. configuration information)
2) FLASH (i.e. self boot image)
Enter 1 or 2 :: 1
Erase all non-volatile EEPROM memory? (y/n) [n]:: y
Erasing <16352 or 8160 bytes> of non-volatile memory.
Please wait . . .
16K->|Data 0xff
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16K->|Data 0x0
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initialized checksum record installed
.
.
.
CSMIM-T1 Hardware Installation Guide
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
If the self-boot option is not installed, the command display looks
like this:
monitor:: erase
Erase all non-volatile EEPROM memory? (y/n) [n]:: y
Erasing <16352 or 8160 bytes> of non-volatile memory.
Please wait . . .
16K->|Data 0xff
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16K->|Data 0x0
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initialized checksum record installed
The erase command does not erase the Ethernet address.
NOTE
Since the erase command erases the IP address, you must
use the addr command to re-enter the CSMIM-T1’s IP address
before reloading any software.
3.2.6
help
Entering help, or ?, displays brief descriptions of the CSMIM-T1 ROM
Monitor commands.
3.2.7
image
The image command sets and displays the name of the image file
containing the CSMIM-T1’s software. The command syntax is:
image [–d | filename]
The filename argument permits up to 100 characters. To return the image
name to its default, enter a pair of double-quote characters (""). The
default image name is oper.56.enet. The image command display looks
like this:
monitor:: image
Enter Image name: [(ip) "oper.56.enet", (mop)
"OPER_56_ENET.SYS"]::
Enter TFTP Load Directory [""]::
Enter TFTP Dump path/filename ["dump.192.9.200.88"]::
3-14
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
The image –d command display looks like this:
monitor:: image -d
Image name: Default (ip): "oper.56.enet"
Default (mop): "OPER_56_ENET.SYS"
TFTP Load Directory: ""
TFTP Dump path/filename: "dump.192.9.200.88"
SELF image name: "oper.56.enet"
The SELF image name appears only if the self-boot image
is loaded.
NOTE
If the image file name contains more than 16 characters, it is
truncated when MOP is attempted.
3.2.8
ipx
The ipx command sets several parameters associated with IPX booting
and dumping. This is useful when loading the CSMIM-T1’s operational
image from a Novell file server. The command syntax is:
ipx [–d]
The ipx command display looks like this:
monitor:: ipx
Enter IPX file server name [<uninitialized>]::mars
Enter Frame type, 0=802.3 1=Ethernet II 2=802.2 3=SNAP\
[802.3]::
Enter IPX dump user name [<uninitialized>]::susans
Enter IPX dump password [<uninitialized>]::********
Verify IPX dump password []::********
Enter IPX dump path [<uninitialized>]::SYS:\user\susans\
CSMIM-T1 Hardware Installation Guide
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
The ipx –d command displays the current settings for all of the entries.
The command display looks like this:
monitor:: ipx -d
IPX preferred load file server: "MARS"
IPX Frame type: “802.3”
IPX dump user name: "SUSANS"
IPX dump password: <SET>
IPX dump path name: "SYS:\user\susans\"
3.2.9
lat_key
The lat_key command allows you to set the LAT key from the ROM
monitor.
The lat_key command is optional and may be purchased
separately.
NOTE
The command syntax is:
lat_key [–d]
The lat_key command display looks like this:
monitor:: lat_key
Enter LAT_KEY: [<uninitialized>]::
The lat_key –d command displays the current LAT key setting:
monitor:: lat_key -d
LAT_KEY: <uninitialized>
3-16
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
3.2.10 mop
The mop command sets the MOP load/dump address. This is useful when
the loading the CSMIM-T1’s operational image from a VAX VMS load
host. The command syntax is:
mop [–d]
The mop command display looks like this:
monitor:: mop
Enter preferred MOP load/dump address [<uninitialized>]::
Load Broadcast Y/N [Y]::
The mop –d command displays the current MOP settings:
monitor:: mop -d
MOP preferred load/dump address <uninitialized>
Load Broadcast: Y
3.2.11 net
The net command executes an Ethernet transceiver loopback test on the
local area network. The command syntax is:
net
The net command display looks like this:
monitor:: net
Network test – PASSED
This transciever loopback test sends out a short test packet from the
CSMIM-T1 through the MicroMMAC to test the integrity of the network.
One of the Ethernet connections (internal AUI or external connection)
must be valid for this test to pass.
CSMIM-T1 Hardware Installation Guide
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
If the unit passes this test, the console displays PASSED. If the
CSMIM-T1 fails, the console displays an error message. Failing this test
indicates that the CSMIM-T1 failed to communicate with the
MicroMMAC. Contact Cabletron Systems Technical Support.
3.2.12 option_key
The option_key command loads an option key from the ROM monitor.
The command syntax is:
option_key [–d ]
The option_key command display looks like this:
monitor:: option_key
Enter option_key [<uninitialized>]::
The option_key –d command displays the current settings:
monitor:: option_key -d
option_key: <uninitialized>
3.2.13 ping
The ping command sends an Internet Control Message Protocol (ICMP)
mandatory ECHO_REQUEST datagram to elicit an ICMP
ECHO_RESPONSE from a host or gateway. ECHO_REQUEST
datagrams (pings) have an IP and ICMP header, followed by a structured
time value and an arbitrary number of pad bytes that fill out the packet.
The syntax for this command is:
ping host_ip_address [data_size] [npackets]
The host_ip_address entry is the Internet address of the host or gateway
from which you wish to elicit a response.
The optional data_size entry is the number of bytes sent in a datagram
packet. The default value is 64 and the maximum value is 1024.
3-18
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
The optional npackets entry is the number of packets to transmit. If you
specify npackets, then you must also specify a data_size.
The ping command display looks something like this:
monitor:: ping 132.245.33.69
PING 132.245.33.69: 64 data bytes
To exit out of ping either wait for npackets to be transmitted or, at any
point, type q. The ping statistics display upon exit.
3.2.14 ports
The ports command tests serial line ports, exercising both the data lines
and the control lines for each serial port specified. The syntax for this
command is:
ports [–d]
Each serial port to be tested must be looped-back with a loopback plug to
test both the data lines and the control lines (the accessory kit provides a
loopback plug). Connect this plug to the connector on the CSMIM-T1
that corresponds to the port to be tested.
Do not run the ports command for a port to which a device is
connected. The test will transmit data to the device and toggle
NOTE
its control lines.
When invoked, the command displays a menu of options.
CSMIM-T1 Hardware Installation Guide
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
monitor:: ports
Individual Port Tests (Data and Control Lines)
Some important notes:
- All Serial Ports (1-7) which are to be tested require a
loopback plug in order to pass the Data Line and Control Line
loopback tests.
WARNING. If there is a device instead of a loopback plug
connected to the port being tested, the device will have data
transmitted to it and its Control Line toggled.
Ports with faulty Control Lines:
Ports with faulty Data Lines:
Enter port number or range of ports to test (Return to exit):: 3
Enter the number of times to loop on this test [1]::
Testing data lines on channel 3
ERROR -- Data line loopback failure on port 3 Testing modem
signals on channel 3
ERROR -- No RTS/CTS turning (ON) loopback interrupt sensed on
Chan 3 !
Pressing the RETURN key after the prompt Selection (Return to exit)
returns you to the monitor prompt.
If you enter the ports –d command, only the data lines are tested. The
outgoing control lines are asserted during this test.
monitor:: ports -d
Individual Port Tests (Data Lines)
Some important notes:
- All Asynch Serial Ports (2-16) which are to be tested require a
loopback plug in order to pass the Data Line loopback tests.
WARNING. If there is a device instead of a loopback plug
connected to the port being tested, the device will have data
transmitted to it.
You may enter a list of ports to test separated by spaces/commas.
You may also enter ranges of ports, such as 2-16.
Ports with faulty Data Lines: 3
Enter port number or range of ports to test (Return to exit)::
3-20
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
3.2.15 sequence
The sequence command edits the load/dump interface list. This list
determines the order of the network interfaces, and either the local area
network (LAN) or the SLIP interface the CSMIM-T1 will use for loading
and dumping. The default, net, uses the LAN interface. The list can
contain up to four interfaces. If the CSMIM-T1 fails to boot using the first
interface, it will try the next, and then the next interface, and then repeat
the sequence. The command syntax is:
sequence [–d] | [interface[,interface]. . .]
Specify the LAN interface by selecting net; specify each SLIP interface
as slnn, where nn is a port number; and specify self-boot by selecting self.
Separate each interface with a comma or a space. Enter the interface list
as an argument to the command; otherwise, the console displays a list of
available interfaces and prompts for a new list.
In the following example, interfaces are assigned to the load/dump
sequence list. Ports 12, 14, and 15 can be added to the list because they
were configured earlier as SLIP interfaces:
monitor:: sequence
Enter a list of 1 to 4 interfaces to attempt to use for
downloading code or upline dumping. Enter them in the order
they should be tried, separated by commas or spaces. Possible
interfaces are:
Ethernet: net
SL/IP: sl12,sl14,s115
SELF: self
Enter interface sequence [net]:: sl12, net
Interface sequence: sl12,net
The SELF option appears only if the self-boot image is loaded.
NOTE
CSMIM-T1 Hardware Installation Guide
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
If you enter the command with the –d argument, the console displays the
current load/dump interface list. You cannot specify both the –d argument
and the interface list with the same command. The sequence –d
command display looks like this:
monitor:: sequence -d
Interface sequence: sl12,net
Entering a number for a port that has not been configured properly for
SLIP causes the Port nn is not configured for SL/IP message to display,
where nn is the port number.
The CSMIM-T1 can slip boot over any port except Port 1.
NOTE
3.2.16 slip
The slip command defines a serial port as a Serial Line Internet Protocol
The command syntax is:
slip [–d] [port]
After entering the command, you are prompted for each parameter. The
port is the number of the serial port to be configured with this command.
If you do not enter a port number, you will be prompted for one. Table
3-2 lists the information for which the slip command prompts.
Entering slip –d causes the command to display all the current settings.
3-22
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
Table 3-2 .The slip Command Prompts
Description
Prompt
Modifies the port’s mode. A y response changes
the port to a SLIP interface. An n response changes
Allow SLIP on this port the port’s mode to CLI. The port is not available as
a SLIP interface and the SLIP parameters are
ignored. The default is n.
Specifies the CSMIM-T1 IP address for this SLIP
Enter local endpoint
interface. The CSMIM-T1 boots over the SLIP
address
interface only if this address is set.
Enter remote
endpoint address
Specifies the IP address of the remote end of the
SLIP interface.
Specifies the IP address of the remote host to
which load and dump requests are sent. This
address is required only if the remote host is a
gateway and not the load host. By default, this is the
same as the remote end-point address.
Enter remote
load/dump host
address
Should this interface
be used for memory
dumps
Enables the CSMIM-T1 to use a SLIP interface for
memory dumps. The default is y.
Specifies the baud rate of the serial interface. The
default is 9600.
Enter the baud rate
Pressing the RETURN key accepts the default
(one). Generally, SLIP implementations require
the default.
Enter the number of
stop bits
Pressing the RETURN key accepts the default
(none). Generally, SLIP implementations require
the default.
Enter the parity
CSMIM-T1 Hardware Installation Guide
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
The slip command automatically sets the number of data bits to 8 for all
SLIP interfaces. The number of data bits does not include the start, stop,
or parity bits. The slip command display looks like this:
monitor:: slip
Line number (1-16):: 6
Allow SL/IP on this port? (y/n) [n]:: y
Enter local endpoint address [0.0.0.0]:: 192.9.200.214
Local endpoint address: 192.9.200.214
Enter subnet mask [255.255.255.0]::
Constructed new subnet mask.
Enter remote endpoint address [0.0.0.0.]:: 192.9.200.0
Remote endpoint address: 192.9.200.0
Enter remote load/dump host address [default 192.9.200.88]::
Using remote endpoint address: 192.9.200.88
Should this interface be used for memory dumps? (y/n) [y]::
Enter the baud rate [9600]::
Enter the number of stop bits (1,1.5,2) [1]::
Enter the parity (none,even,odd) [none]::
Pressing CONTROL + C interrupts the slip command; the
parameters remain unchanged until the command completes
NOTE
normally.
3-24
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
3.2.17 stats
The stats command displays current network statistics gathered by the
ROM. Use stats along with the boot command to help isolate problems.
Table 3-3 describes the network statistics displayed by the stats
command. The syntax is:
stats [-slip]
The stats command display looks like this:
monitor:: stats
Ethernet Statistics
Frames Received:
CRC Errors:
398
0
Frames Sent:
Carrier Sense Losses:
3
0
Alignment Errors:
Resource Drops:
Bus Wait Drops:
Bad Types/Lengths:
0
0
0
0
Clear to Send Losses:
Collisions Detected:
Excessive Collision Losses
0
0
0
Table 3-3 .Network Statistics
Statistic
Description
Frames Received
CRC Errors
The number of frames received.
The number of CRC checksum errors detected.
The number of frames received misaligned with a CRC
error.
Alignment Errors
Resource Drops
Bus Wait Drops
The number of packets dropped because the ROM
code could not buffer them quickly enough. The ROM
code cannot always handle back-to-back incoming
packets. The CSMIM-T1 accepts the first response it
receives and drops all others. Dropped packets are
normal.
The number of packets dropped due to waiting too
long for a bus to become available.
CSMIM-T1 Hardware Installation Guide
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: ROM Monitor Commands
Table 3-3 .Network Statistics (Continued)
Description
Statistic
The number of unknown packet types if Ethernet IP
encapsulation is being used. The number of packets
with illegal lengths if IEEE 802.2/802.3 IP
encapsulation is being used.
Bad Types/
Lengths
Frames Sent
The number of frames sent.
The number of times packets could not be transmitted
because the CSMIM-T1 lost the Carrier Sense signal –
usually the result of excessive traffic on the Ethernet.
Carrier Sense
Losses
The number of times packets could not be transmitted
because the CSMIM-T1 lost the Clear to Send signal –
usually the result of excessive traffic.
Clear to Send
Losses
The number of times the CSMIM-T1 had to retry
transmissions automatically – usually the result of
normal Ethernet traffic. These retries do not cause the
boot command to display ‘‘*.”
Collisions Detected
The number of times the CSMIM-T1 could not transmit
packets because there were too many collisions –
usually the result of excessive traffic on the Ethernet.
The boot command displays these retries as “*.”
Excessive Collision
Losses
3-26
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4
CSMIM-T1 PARAMETERS
4.1
GENERAL
The CSMIM-T1 comes with software that supports specific commands
and parameters for the configuration and administration of the
CSMIM-T1 module. These commands cannot be accessed through the
console port. You must either telnet into the CSMIM-T1 from another IP
address, or you may use the NA utility. Also note that these commands are
not available until after the unit has successfully booted. The following
sections describe the commands and parameters, and Section 4.5 provides
an example of how to use them.
4.2
T-1 COMMANDS
The CSMIM-T1 software comes with the following new or enhanced
commands:
Table 4-1 T1-related Commands
Command
Command Type
Description
stats -T
CLI
Displays T-1 Network Interface
statistics.
show
set
admin / na
admin / na
admin / na
Shows a T-1 configuration parameter.
Sets a T-1 configuration parameter.
reset
Resets the T-1 engine and ESF
statistics.
t1_loopback
Superuser CLI
Places the T-1 engine into loopback
mode.
CSMIM-T1 Hardware Installation Guide
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: CSMIM-T1 Parameters
stats -T
The stats -T command displays T-1 network interface statistics for the
Annex. Table 4-2 describes the arguments for stats -T. The syntax is:
stats -T [ current | total | all | interval_set | clear_alarm ]
Table 4-2 Arguments for the stats -T Command
Argument
Description
current
Displays Extended Super Frame (ESF) statistics for the
current fifteen minute interval. The tni_framing parameter
must be set to esf (default). If the tni_framing parameter is
set to d4, the current statistics are not displayed.
total
Displays the total number of ESF statistics collected.
Displays all ESF statistics.
all
interval _set
Displays a specific ESF interval.You can enter a single
interval or a range of intervals from 1 to 96. Interval 1 is the
most recent interval.
clear_alarm
Clears the alarm condition saved in the history buffer.
The stats -T current command display looks like this:
annex# stats -T current
alarm history: [ no blue no red no yellow ], Fri July 28 16:48:37 1995 EDT
Alarms:
no blue
no red
no yellow
engine:
no loss of signal
offline
08
no sync
no D&I sync
serial number:
circuit ID:
T1 info:
unit ID: XYLOGICS T1-ENGINE 085234 Rev. A 07/19/95 6343
loopback mode: No loopback
uptime: 69:07:49
Current Statistics
469
number of valid seconds:
bursty errored seconds (ESF only):0
errored seconds:
Controlled slip seconds:0
Severly errored seconds:0
0
0
unavailable seconds:
out of frame errors:
CRC errors (ESF only):
received net alarms:
0
0
0
bipolar violations:
controlled slilps:
0
0
annex#
4-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
T-1 Commands
The information displayed at the beginning of every stats -T command is
described in Table 4-3.
Table 4-3 stats-T Command Information
Field
Description
Sync
When Sync is true, the T-1 engine is detecting frame
synchronization. When Sync is false, the T-1 engine has lost
frame synchronization and enters the red alarm state.
Loss of Signal
When Loss of Signal is true, the T-1 engine is not detecting
pulses on the T-1 network interface receiver. When Loss of
Signal is false, the T-1 network interface is receiving pulses.
The loss of signal condition causes the T-1 engine to transmit
AIS (all ones unframed) on the T-1 network interface.
Blue Alarm
Red Alarm
When the Blue Alarm is true, the T-1 engine is receiving AIS
(all ones unframed) from the network.When the Blue Alarm is
false, the T-1 engine is not receiving AIS. The Blue Alarm
event saved in the history buffer is also displayed.
When the Red Alarm is true, the T-1 engine has detected loss
of frame synchronization. During this condition, the T-1
interface is sending a Yellow Alarm to the network. When the
Red Alarm is false, The T-1 engine is in frame synchronization
and the sync indication is true. The Red Alarm event saved in
the history buffer is also displayed.
Yellow Alarm
Loopback
When the Yellow Alarm is true, the T-1 engine is receiving a
Yellow Alarm from the network. When the Yellow Alarm is
false, the T-1 engine is not receiving a Yellow Alarm from the
network. The Yellow Alarm event saved in the history buffer is
also displayed.
The loopback status has the following possible states:
None - There is no loopback in progress.The test LED on the
front panel is not illuminated.
Local - The T-1 network interface is in local loopback.The test
LED on the front panel is illuminated.
Line - The T-1 network interface is in line loopback. The test
LED on the front panel is illuminated.
Payload - This means that the T-1 network interface is in
payload loopback. The test LED on the front panel is
illuminated.
CSMIM-T1 Hardware Installation Guide
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: CSMIM-T1 Parameters
Table 4-3 stats-T Command Information
Field
Description
Online
When illuminated, the T-1 engine is engaged with the
network. Otherwise, the T-1 Network Interface and
Drop/Insert Interface are isolated from the T-1 engine.
Up Time
Amount of time the T-1 engine has been up, in hours,
minutes, and seconds. The “hours” field is a 16-bit register
that can count up to 2700 days (less than 7 years).
Serial Number
Circuit ID
The T-1 engine’s serial number.
The T-1 engine’s Circuit ID displayed from the tni_circuit_id
parameter.
Unit ID
The T-1 engine’s Unit ID displayed as:
“XYLOGICS T1-ENGINE 085nnn Rev. n mm/dd/yy xxxx”
Where:
085nnn - This is the firmware number.
Rev. n - This is the firmware revision number.
mm/dd/yy - This is the firmware release date.
xxxx - This is the EPROM check sum.
DII Sync
Interval
When DII Sync is true, the Drop/Insert Interface is receiving
ones pulses and is in frame sync. When DII Sync is false, the
Drop/Insert Interface is out of frame sync or not receiving
pulses and is sending AIS (all ones framed).
The 15-minute interval being displayed. This is an integer
from 1 to 96, “current” or “total”.
Number ofValid Part of the “current” report that indicates the number of
Seconds
seconds for which the statistics data has been collected.
Number of
15-minute
Periods
Part of the “total” report that indicates the number of valid
15-minute periods. This could also be derived from the
uptime.
Bursty Errored
Seconds
A Bursty Errored Second (BES) is a second with more than
one, but less than 320 CRC error events.
Controlled Slip A Controlled Slip Second (CSS) is a second with one or more
Seconds Controlled Slips.
4-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
T-1 Commands
Table 4-3 stats-T Command Information
Description
Field
Errored
Seconds
An Errored Second is a second with one or more ESF error
events; that is, one or more CRC error events or one or more
Out of Frame (OOFs).
Severely
Errored
A Severely Errored Second (SES) is a second with 320 or
more CRC error events or one or more OOF error events.
Seconds
Unavailable
Seconds
Unavailable Seconds (UAS) are a count of one-second
intervals during which service is unavailable.
show t1
The show t1 command displays current T-1 configuration parameters:
The syntax is:
show t1 t1_parameter
set t1
The set t1 command requires superuser privileges, and modifies
CSMIM-T1 configuration parameters.
The syntax is:
set t1 t1_parameters
reset
The reset command requires superuser privileges. A reset terminates any
active connections.
The reset t1 command resets the T-1 engine and the extended super
framing (ESF) statistics. This command is used to change the T-1 engine’s
parameter configuration. The T-1 soft, hard, and esf keywords are
described in Table 4-4 . The syntax is:
reset t1 [soft | hard | esf]
CSMIM-T1 Hardware Installation Guide
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: CSMIM-T1 Parameters
The reset internal_modem command resets the specified T-1
modem_set. There is no physical reset button. A modem reset forces the
port to be reset. In addition, if the signal protocol is set to wink start or
immediate start, a special AT command is sent to the modem to select the
dialtone detection mechanism.
The modem_reset parameter specifies the individual modem numbers,
separated by commas, or a range of numbers separated by a hyphen. The
valid modem number range is 1 to 24, inclusive.
Table 4-4 Keywords for the reset t1 Command
Keyword
Definition
soft
This setting reconfigures the software parameters and will
only disrupt the service on the DS0 channels that are
changed.
hard
esf
This setting resets the T-1 engine causing the T-1 Drop/Insert
interface and modem sessions to terminate.
Note: If modem sessions and/or equipment are attached to
the Drop and Insert Interface, their service will be interrupted
for a short period of time (usually a few seconds).
This setting resets all the ESF counters in the T-1 engine.
4-6
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
T-1 Commands
T1_loopback
The superuser T1_loopback command places the T-1 engine into loopback
mode. None of the loopback conditions persist through a power down or
reboot. A major consideration to those using the T-1 service must be made
service. To switch between two different types of loopback, the first
loopback must be cancelled before specifying the second loopback.
The syntax for the T1_loopback command is:
T1_loopback [ none | line | payload | local ]
Table 4-5 describes the arguments for T1_loopback.
Table 4-5 Arguments for the T1_Loopback Command
Argument
Description
None
No loopback. This is the default. If the T1_loopback
command is initiated with no parameters, then none is
assumed. It cancels any user specified loopbacks.
Line
Line loopback provides the network a means to test the
T-1 circuit for single ended fault isolation. The line
loopback regenerates the DS1 signal and does not
correct bipolar violations.
Payload
Local
Payload loopback is used to provide a loopback toward
the network. The data portion of the DS0 is looped
back.
Local loopback will loop back the data from the
customer side of both the T1 Network Interface and the
T1 Drop/Insert Interface.
Please Note: Network direction loopbacks in most
cases can be initiated by the Telco. The front panel Test
indicator illuminates when the T-1 is in loopback.
CSMIM-T1 Hardware Installation Guide
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: CSMIM-T1 Parameters
4.3
T-1 PARAMETERS
The CSMIM-T1 software comes with the following new T-1 parameters:
Keyword
Description
alarmsyslog
Sets or displays parameter setting as yes or no. These
values enable or disable the alarm event syslogs.
bypass
Sets or displays parameter setting as yes or no. A setting
of yes removes the T-1 engine from the network.
map
ring
Sets or displays mappings for the DS0 channels.
Sets or displays parameter setting as yes or no. A setting
of yes means that an audible ring is sent to the service
provider for incoming calls.
sigproto
t1_info
Sets or displays the inbound and outbound signaling
protocol settings for each DS0 channel.
Sets or displays a character string (128 bytes maximum)
of printable ASCII characters that describe installation
information from the service provider.
tni_circuit_id
tni_clock
Sets or displays the T-1 circuit identifier string (128
characters maximum) required by the service provider for
customer service calls.
Sets or displays parameter setting as loop, local, or
external. These values represent the source for the T-1
clock.
tni_esf_fdl
tni_framing
Sets or displays parameter setting as ansi or att. These
values represent the Facilities Data Link standard.
Sets or displays parameter setting as d4 or esf. These
values represent the superframe format setting on the T1
Network Interface.
tni_line_buildout
Sets or displays parameter setting as 0, 7.5, 15, or 22.5.
These values represent the cable loss measurement
between the last line generator and the customer location.
4-8
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter Descriptions
Keyword
Description
tni_line_code
Sets or displays parameter setting as ami or b8zs. These
values represent the line code used on the T1 Network
Interface.
tni_ones_density Sets or displays the T1 Network Interface ones density
setting as on or off.
tdi_distance
tdi_framing
tdi_line_code
Sets or displays an integer from 0 to 655 that represents
the length of the cable from the T1 Drop/Insert Interface to
the PBX or other equipment.
Sets or displays the superframe format used on the T1
Drop/Insert Interface as d4 (superframe) or esf (extended
superframe). The default is esf.
Sets or displays the T1 Drop/Insert Interface line code
setting as either ami or b8zs. The default is b8zs.
4.4
PARAMETER DESCRIPTIONS
The CSMIM-T1 software comes with the following new parameters:
alarmsyslog
This T-1 parameter enables or disables the T-1 alarm event syslogs. A Y
enables this parameter, an N disables it. The default is Y.
bypass
This T-1 parameter is used to remove the T-1 engine from the network.
When bypass is set to Y, the T1 engine is off-line and the T1 Network
Interface (T1NI) and the T1 Drop and Insert Interface (T1DII) are
physically isolated from the T-1 engine. When bypass is set to Y, the T-1
engine has no effect on the T-1 circuit. When bypass is set to N, the T-1
engine is attached to both the T1NI and the T1DII. The default is Y.
CSMIM-T1 Hardware Installation Guide
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: CSMIM-T1 Parameters
map
This T-1 parameter controls the mapping of the modems to the T1 Drop
and Insert Interface (T1DII) and the T1 Network Interface (T1NI) DS0
slots/channels. The modems can be mapped to any unoccupied slot on the
T1NI or the T1DII. The T1NI and the T1DII can be mapped to each other
on channels that are not occupied by modems. Information flowing
between the T1NI and a modem and the T1DII and a modem flows as
voice, not data. Table 4-6 lists the options that are used with the map
parameter.
Table 4-6 Options for the Map Parameter
Option
Description
map_val modem_number These options map an interface to a modem.
The map_val option defines the interface as:
ds for the T1 Network Interface (the DS0
channel).
di for the Drop/Insert Interface.
The modem_number option must be specified.
The modem_number value is a number from 1 to
24.
map_val
The map_val option by itself maps the T1
Network Interface to the Drop/Insert Interface.
The map_val defines the type of channel as
data, voice, or unused.
ring
This T-1 parameter is used to provide the audible ring to the central office
for incoming calls. The default is Y, and the audible ring is sent to the
central office. This parameter is used with wink_start and immediate_start
protocols only.
4-10
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter Descriptions
sigproto
This T-1 parameter is used to specify the inbound and outbound signaling
protocols supported by each T-1 channel (DS0). Each channel supports an
inbound protocol and an outbound protocol. Both protocols must be
specified even if they are the same. If the protocol pair is invalid, it is
rejected with an error message. For inbound-only channels, the outbound
protocol must be set to none. For outbound-only channels the inbound
protocol must be set to none.
t1_info
This T-1 parameter stores installation information from the service
provider, such as a telephone number to call should the network go down.
This parameter is limited to a 128-byte string of printable ASCII
characters.
tdi_distance
This T-1 parameter defines the distance, in feet, of the cable that runs
from the T1DII to the Private Branch Exchange (PBX) or other
equipment. The parameter setting is an integer from 1 to 655. The default
setting is 0.
tdi_framing
This T-1 parameter controls which superframe format is used on the T1
Drop/Insert Interface. The parameter settings are d4 (superframe) and esf
(extended superframe). The default setting is esf. The value for
tdi_framing may or may not be the same as tni_framing.
tdi_line_code
This T-1 parameter selects the line code to be used on the T1 Drop/Insert
Interface (T1DII). The device connected to the T1DII determines which
line code to use. The parameter settings are ami and b8zs. The default
setting is b8zs.
tni_circuit_id
This T-1 parameter stores the T-1 circuit identifier string. The T-1 circuit
identifier string comes from the service provider and is used for customer
service calls. The parameter setting is a string of up to 128 characters. The
default setting is the null string.
CSMIM-T1 Hardware Installation Guide
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: CSMIM-T1 Parameters
tni_clock
This T-1 parameter sets the clock for the T1 Network Interface. Parameter
settings include loop (service provider), local (Annex), external (T1
Drop/Insert Interface). The default setting is loop.
tni_esf_fdl
This T-1 parameter sets the T-1 facilities data link (FDL) format. The FDL
format is used in conjunction with the ESF format and determined by the
service provider. The parameter settings include ANSI (ANSI T1.403)
and AT&T (AT&T TR54016) standard formats.
tni_framing
This T-1 parameter controls which super frame format is used on the
T1 Network Interface. Parameter settings include d4 (superframe) and esf
(extended superframe). The default setting is esf. The value for
tni_framing may or may not be the same as tdi_framing.
tni_line_buildout
This T-1 parameter sets the Line Build-Out (LBO) value. The Channel
Service Unit (CSU) portion of the T1 Network Interface requires the
administrator to configure a LBO value. The service provider will supply
a value based on the amount of cable loss from the service provider’s
location to the module. Parameter settings include 0, 7.5, 15, and 22.5.
The default is 0.
tni_line_code
This T-1 parameter selects the line code for the T1 Network Interface. The
service provider determines the line code setting. Parameter settings
include ami and b8Zs. The default setting is b8zs.
4-12
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Set T-1 Parameters Example
tni_ones_density
This T-1 parameter is used to defeat the CSMIM-T1 ones density monitor.
The T-1 engine has a built in ones density monitor that will provide the
network with the correct number of one pulses. The ones density monitor
does the following:
1. The monitor does not allow the CSMIM-T1 to transmit more than
fifteen consecutive zeros.
2. The monitor ensures that the CSMIM-T1 has at least N ones in every
time window of 8X(N+1) bits, where N=1 to 23.
This parameter has an on and an off setting. This parameter should be set
to on when using AMI coding. The default is off.
4.5
SET T-1 PARAMETERS EXAMPLE
The following is an example of the show, set, and reset commands and
provides actual screens to reference while proceeding. What we have
done is show the T-1 info screen, set the T-1 bypass to N allowing the T-1
line to interface with the module, change the loop start setting to wink
start, and reset the software at the appropriate times. This is an actual
example of how to make the T-1 module functional.
annex: su
Password:
annex# ad
ANNEX3-UX R10.1, 24 async ports, 0 printer ports
admin: show t1
Channelized T1 Generic Parameters
alarmsyslog: Y
bypass: Y
t1_info: “”
tni_clock: loop
tni_line_buildout: 0dB
tni_framing: esf
tni_esf_fdl: att
tdi_framing: esf
tdi_distance: 0
tni_ones_density: off
tni_line_code: b8zs
tni_circuit_id: “”
tdi_line_code: b8zs
admin: set t1 bypass n
You may need to reset the appropriate port, Annex subsystem or
reboot the Annex for changes to take effect.
admin: res t1 soft
admin: sho t1 ds0
CSMIM-T1 Hardware Installation Guide
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: CSMIM-T1 Parameters
T1 DS0 Map Parameters
map: ds0=1 ds1_modem 1
ds0=2 ds1_modem 2
ds0=3 ds1_modem 3
ds0=4 ds1_modem 4
ds0=5 ds1_modem 5
ds0=6 ds1_modem 6
ds0=7 ds1_modem 7
ds0=8 ds1_modem 8
ds0=9 ds1_modem 9
ds0=10 ds1_modem 10
ds0=11 ds1_modem 11
ds0=12 ds1_modem 12
ds0=13 ds1_modem 13
ds0=14 ds1_modem 14
ds0=15 ds1_modem 15
ds0=16 ds1_modem 16
ds0=17 ds1_modem 17
ds0=18 ds1_modem 18
ds0=19 ds1_modem 19
ds0=20 ds1_modem 20
ds0=21 ds1_modem 21
ds0=22 ds1_modem 22
ds0=23 ds1_modem 23
ds0=24 ds1_modem 24
more:
T1 DS0 Signaling Protocol Parameters
sigproto: ds0=1 loop_start
loop_start
ds0=2 loop_start loop_start
ds0=3 loop_start loop_start
ds0=4 loop_start loop_start
ds0=5 loop_start loop_start
ds0=6 loop_start loop_start
ds0=7 loop_start loop_start
ds0=8 loop_start loop_start
ds0=9 loop_start loop_start
ds0=10 loop_start loop_start
ds0=11 loop_start loop_start
ds0=12 loop_start loop_start
ds0=13 loop_start loop_start
ds0=14 loop_start loop_start
ds0=15 loop_start loop_start
ds0=16 loop_start loop_start
ds0=17 loop_start loop_start
ds0=18 loop_start loop_start
more:
4-14
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Set T-1 Parameters Example
ds0=19 loop_start loop_start
ds0=20 loop_start loop_start
ds0=21 loop_start loop_start
ds0=22 loop_start loop_start
ds0=23 loop_start loop_start
ds0=24 loop_start loop_start
T1 DS0 Ring Parameters
ring: ds0=1
yes
yes
yes
yes
yes
yes
yes
yes
yes
ds0=2
ds0=3
ds0=4
ds0=5
ds0=6
more: ds0=7
ds0=8
ds0=9
ds0=10
ds0=11
ds0=12
ds0=13
ds0=14
ds0=15
ds0=16
ds0=17
ds0=18
ds0=19
ds0=20
ds0=21
ds0=22
ds0=23
ds0=24
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
admin :
admin : set t1 ds0=all sigproto wink_start wink_start
You may need to reset the appropriate port, Annex subsystem or
reboot the Annex for changes to take effect.
admin : res t1 soft
admin : q
annex# ha
CSMIM-T1 Hardware Installation Guide
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: CSMIM-T1 Parameters
4-16
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5
TROUBLESHOOTING PROCEDURES
5.1
GENERAL
The CSMIM-T1’s front panel contains a number of LEDs that provide
information about normal operations and about problems that occur. Use
these LEDs and the ROM Monitor commands to diagnose problems.
Figure 5-1 illustrates the CSMIM-T1’s front panel LEDs.
CSMIM-T1
SN
1-8
17-24
STAT
S/U
MODEM
CONFIG
STATUS
9-16
ATTN TRAF
CD TX RX
A
B
C
1
2
3
4
5
SET UP
6
7
8
9
10
11
12
13
CONSOLE
MODEM
PORT
STATUS
14
15
16
17
18
19
20
21
22
23
24
TEST
LOS
BLU
SYNC
NETWORK
STATUS/
ALARMS
RED
YEL
ON LINE
T1 NETWORK
INTERFACE
DROP/INSERT
INTERFACE
DI SYNC
ETHERNET
Figure 5-1 CSMIM-T1 Front Panel
CSMIM-T1 Hardware Installation Guide
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
Refer to Table 5-1 for a description of the LEDs located on the front of
the CSMIM-T1.
Table 5-1 CSMIM-T1 Front Panel LEDs
LED(s)
Description
MODEM CONFIG
STATUS
These LEDs indicate the number of modems installed
(8, 16, or 24). An indicator is green if all the modems
in its group are good. An indicator is amber if one
modem in its group is bad.
MODEM PORT
STATUS
The CSMIM-T1 has three status indicators for each
modem port (1 through 24):
CD - Data Carrier Detect is a green LED and is on
when the carrier has been detected on the telephone
line on the corresponding modem.
TX - Transmit Data is a green LED that flashes to
indicate the corresponding modem is transmitting
data.
RX - Receive Data is a green LED that flashes to
indicate the corresponding modem is receiving data.
NETWORK STATUS
TEST - RED network TEST indicator is ON when the
T1 Network Interface is looped back. Loopback tests
are activated either locally by the user or by the
telephone company.
SYNC - GREEN SYNC indicator is ON when the T1
engine is properly synchronized with the received
network signal and is receiving proper framing
information.
LOS - RED LOS indicator is ON when the T1 engine
is detecting no signal (pulses) on the network
interface receiver. When a LOS condition exists, the
T1 engine transmits unframed all one (AIS) to the
network.
5-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
General
LED(s)
Description
NETWORK ALARMS
RED - RED alarm indicator is ON during a locally
detected carrier failure. During the RED alarm
condition, a YELLOW alarm is transmitted across the
telephone network.
YEL - YELLOW alarm indicator is ON when receiving
a YELLOW alarm condition from the telephone
network.
BLU - BLUE alarm indicator is ON when receiving
an unframed, all-ones Alarm Indication Signal
(AIS) from the network. This condition exists upon
a loss of originating signal, or when any action is
taken that would cause a signal disruption.
ON LINE
DI SYNC
This LED is green and ON when the T1 engine is
connected to a T1 line.
This LED is green and ON when the T1 engine is
detecting frame synchronization on the drop and
insert interface receiver.The green LED is OFF when
there is a loss of frame (LOF) synchronization.
A LOF condition causes the T1 engine to transmit
unframed all ones (keep-alive) to the device attached
to the Drop and Insert Interface.
SYSTEM
ATTN - The ATTN (Attention) indicator is amber and
ON when the CSMIM-T1 requires operator attention.
The indicator is flashing when there is a problem.
STAT - The STAT (Status) indicator is green and ON
after the CSMIM-T1 passes the core power-up
diagnostics. The indicator flashes after resetting the
CSMIM-T1.
TRAF - The TRAF (Traffic) indicator is green and
flashing when the CSMIM-T1 successfully transmits
or receives data from the LAN.
SETUP - The SETUP indicator is green when the
SETUP button is pressed ON (SETUP Mode) and
flashing when the SETUP button is pressed ON for 3
seconds (RESET Mode).
Ethernet Channel
Three green LED’s that indicate the Ethernet channel
Indicators A, B, and C that is selected by either the software or jumper
configuration.
CSMIM-T1 Hardware Installation Guide
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
During power-up and booting, it is more difficult to diagnose problems
because they can originate in the CSMIM-T1, the network, or the load
server host. However, the LEDs provide both a progress report and an
error display to assist you in troubleshooting.
If an error occurs, save the status of these LEDs. Technical
support personnel can use this information to diagnose
NOTE
problems.
5.2
POWER-UP AND BOOT PROCEDURES
The CSMIM-T1 has two modes of operation: normal and set up. Normal
mode is the standard operational mode. SET UP mode provides access to
the ROM Monitor commands. Pressing the SET UP button on the front
panel puts the CSMIM-T1 into SET UP mode. When the CSMIM-T1 is in
SET UP mode, the SET UP LED lights.
During the CSMIM-T1 power-up and boot sequence, the CSMIM-T1
runs a set of diagnostics. The system LEDs display the diagnostics’status.
The CSMIM-T1 stops when it detects one of two error conditions (see
Table 5-2). The pattern of the system LEDs identifies the error condition.
5.2.1
Normal Mode CSMIM-T1 Diagnostics
Following power-up or reset, the CSMIM-T1 enters normal mode. The
following subsections describe both the possible error and error-free
conditions that can occur during power-up and booting in normal mode.
5-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Power-Up and Boot Procedures
5.2.1.1 Normal Mode Error-Free Sequence
Table 5-2 summarizes the LED display states during error-free power-up
in normal mode. The following subsections describe these states.
Table 5-2 Normal Mode Error-Free LED States
STAT
Green
ATTN
Amber
TRAF
Green
Activity
N1: LEDs OK
N2: Hardware OK
●
●
●
✕
●
●
Key:
●
✕
On continuously.
Off.
■
◆
Flashing irregularly.
Flashing regularly (about 1Hz).
Activity N1:Testing LEDs
All front panel LEDs light for a few seconds, then all but the Ethernet
LED (segment indicator) turn off, confirming that all LEDs are
operational.
Activity N2:Testing the Hardware
During the power-up sequence, the CSMIM-T1 runs a series of self-test
diagnostics. These diagnostics test internal hardware functions. If a test
fails, the ATTN and STAT LEDs flash and an error message is displayed
on the console port. The TRAF indicator flashes during the power-up
self-tests. After the self-tests complete, only the STAT and Ethernet
channel indicator remain on.
CSMIM-T1 Hardware Installation Guide
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
5.2.1.2 Normal Mode Error Sequence
Table 5-3 shows the state of the indicators when an error occurs at various
stages of the start-up process. If the CSMIM-T1 fails during the
hardware-test state (N2), the error condition is hardware failure NE2. A
description of possible causes and solutions for each error condition is in
the following paragraphs.
Table 5-3 Normal Mode Error LED States
STAT
Green
ATTN
Amber
TRAF
Green
Activity
NE2: Hardware Failure
NE5: Booted wrong image
◆
◆
◆
✕
●
●
Key:
●
On continuously.
✕
■
◆
Off.
Flashing irregularly.
Flashing regularly (about 1Hz).
Activity NE2: Hardware Failure
The ROM diagnostics detected a CSMIM-T1 hardware problem requiring
service. Call Technical Support.
Activity NE5: Booted Wrong Image
The CSMIM-T1 loaded the wrong image. Press the SET UP button for 3
seconds to reset the device. Following is a list of ways to prevent this
problem in the future:
•
•
Be sure that you configure the CSMIM-T1 with the appropriate image.
Be sure that the image you are booting has the right name. Don’t
rename the image file unless you are making a copy for safe keeping.
•
If you used an na, admin, or cli boot command, specify the correct
image and a valid filename.
5-6
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Power-Up and Boot Procedures
If you do not know why the CSMIM-T1 booted the wrong image, enter
the ROM Monitor mode and issue an image -d command. The command
display will list the image file the CSMIM-T1 is trying to load.
5.2.2
SET UP Mode
Enter SET UP Mode by pressing the SET UP button located on the
CSMIM-T1 front panel. Press this button within 30 seconds of resetting
or powering up the device.
5.2.2.1 SETUP Mode Error-Free Sequence
Table 5-4 summarizes the LED sequences that display in test mode during
an error-free start-up. A description of each sequence follows Table 5-4.
Table 5-4 Normal Mode Error LED States
STAT
Green
ATTN
Amber
TRAF
Green
Activity
T1: Testing Indicators
T2: Testing Hardware
T3: At Monitor Prompt
●
●
●
●
✕
●
●
■
■
Key:
●
On continuously.
✕
■
◆
Off.
Flashing irregularly.
Flashing regularly (about 1Hz).
Activity T1:Testing Indicators
All front panel indicators light for a few seconds, then all but the Ethernet
channel indicator turn off. This sequence confirms that all indicators are
operational. At this point, the CSMIM-T1 is in normal mode. Press the
SET UP button to put the CSMIM-T1 into ROM monitor mode.
CSMIM-T1 Hardware Installation Guide
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
Activity T2:Testing the Hardware
During power-up, the CSMIM-T1 runs self-tests that execute diagnostics
for the CPU, ROM, EEPROM, FLASH, etc. The TRAF indicator flashes
during the tests and after completing the power-up self-tests, the STAT
and Ethernet channel indicators remain on.
Activity T3: At the Monitor Prompt
displays on the console terminal. Enter the boot command at the prompt.
If you do not enter a filename with the command, you are prompted to do
so.
5.2.2.2 SETUP Mode Error States
Table 5-5 contains a description of the indicators that are used to describe
errors that occur at different stages of the system start-up process. If the
CSMIM-T1 fails while testing the hardware, (state T2), the error
condition is hardware failure TE2. A description of each error condition
follows Table 5-5.
Table 5-5 Normal Mode Error LED States
STAT
Green
ATTN
Amber
TRAF
Green
Activity
TE2: Hardware Failure
TE7: Booted Wrong Image
◆
◆
◆
✕
✕
●
Key:
●
On continuously.
✕
■
◆
Off.
Flashing irregularly.
Flashing regularly (about 1Hz).
5-8
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOT Failures
Activity TE2: Hardware Failure
The ROM diagnostics detected a CSMIM-T1 hardware problem requiring
service. Call Technical Support.
Activity TE7: Booted Wrong Image
The CSMIM-T1 loaded an inappropriate image. Press the SETUP button
for three seconds to reset the device. Following is a list of ways to prevent
this problem in the future:
•
•
•
Be sure that you configure the CSMIM-T1 with the appropriate image
(oper.46.enet).
Be sure that the image you are booting has the right name. Don’t
rename the image file unless you are making a copy for safe keeping.
If you used an na, admin, or cli boot command, specify the correct
image and a valid filename.
5.3
BOOT FAILURES
The procedures for troubleshooting a power-up failure established that
•
•
•
The hardware is functional.
The Ethernet interface is functional.
The CSMIM-T1 can communicate with the Ethernet.
If the CSMIM-T1 still is not booted, you must pinpoint the problem. The
boot error report can help in this process.
The CSMIM-T1generates a boot error report only if it opens the
boot file and an error occurs during the boot process.
NOTE
Generally, two problems cause boot failures:
•
•
The CSMIM-T1 is not configured properly.
The load server host is not responding.
CSMIM-T1 Hardware Installation Guide
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
The CSMIM-T1 requests a boot image from a pre-defined load host or by
broadcasting a boot request. When a host responds, the CSMIM-T1 loads
its operational image.
The CSMIM-T1 requires setting certain configuration parameters. Enter
these parameters using the ROM Monitor commands for the initial boot
sequence. See Chapter 3 for more information on these commands.
If the problem is a non-responsive host, the boot error report displays that
information under the Rsp T/O’s field. This field indicates that the
CSMIM-T1 timed out while waiting for a response to its boot request; if
this field is empty, check the CSMIM-T1’s configuration parameters.
5.3.1
Boot Error Report
If an error occurs, a CSMIM-T1 boot error report is generated only if the
CSMIM-T1 has opened the boot file. The report is displayed using the
following format:
BOOT ERROR REPORT (for BFS files only)
Boot attempt from host nn.nn.nn.nn:
Errors from Last Open Request:
0 ARP errors 0 ERPC layer errors 0 Aborts rx’d
Errors from Last Read Request:
0 Msgs w/ wrong size 0 ERPC layer errors 0 Aborts rxd
Errors from Last ERPC Layer Invocation:
0 H/W errors 1 Msgs from wrong host 0 Rsp T/O’s 0 Msgs of wrong type
TFTP error codes.
NOTE
The CSMIM-T1 generates a boot error report for the Internet address
from which it tried, and failed, to boot. Table 5-7 contains a description of
the Errors from the Last Read Request; and Table 5-6 contains a
description of the Errors from Last ERPC Layer Invocation.
5-10
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOT Failures
The error count pinpoints the error that caused the boot failure. For
example, if the boot failed during a Read Request due to excessive
Expedited Remote Procedure Call (ERPC) layer errors, the Errors from
Last ERPC Layer Invocation lists only errors that occurred during the
failed Read Request (see Table 5-6). The report does not list errors that
occurred during any other Read Request (see Table 5-7) or during the
Open Request (see Table 5-8).
The Open Request and the Read Request layers communicate with the
block file server (BFS) on the host. The ERPC layer resides below the
Open Request and the Read Request layers. It is responsible for sending a
given message to a specific host UDP port, and for receiving the correct
response to that message from the port.
Table 5-6 Errors from Last ERPC Layer Invocation
Error
Description
H/W errors
The CSMIM-T1 sensed a hardware error during message
transmission or reception. This error indicates a fault with the
CSMIM-T1 LAN interface. Use the net command to isolate the
problem.
Msgs from
wrong host
The CSMIM-T1 received a message from an incorrect host.
This indicates that the CSMIM-T1 received, and ignored, an
unsolicited packet.
Rsp T/O’s
The CSMIM-T1 never received a correctly formatted response
from the correct host, or any response from any load server
hosts.
Msgs of wrong The correct host sent a message to the CSMIM-T1, but the
type
message was not a correctly formatted response to the
transmitted request.
CSMIM-T1 Hardware Installation Guide
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
Table 5-7 Errors from Last Read Request
Error
Description
Msgs with wrong size The correct host responded to the Read Request, but
the data size is incorrect.
ERPC layer errors
Aborts rx’d
See Table 5-6.
The host’s BFS transmitted an abort in response to the
CSMIM-T1’s Read Request. Run erpcd –D on the host
to obtain more information.
Table 5-8 Errors from Last Open Request
Description
Error
ARP errors
Address Resolution Protocol (ARP) errors indicate that the
CSMIM-T1 is configured to boot from a specified host, but
the host would not transmit its Ethernet address to the
CSMIM-T1. Possibly, the CSMIM-T1 configuration
includes the wrong IP encapsulation.
ERPC layer errors See Table 5-6
Aborts rx’d
The host’s BFS transmitted an abort in response to the
CSMIM-T1’s Open Request. This often means that the
requested file does not exist on that server. Run erpcd –D
on the host to obtain more information.
5-12
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOT Failures
5.3.2
Correcting CSMIM-T1 Parameters
The following parameters must accurately reflect both the CSMIM-T1
and the network environment in which it operates.
Verify the CSMIM-T1’s IP address using the addr command. If your
network configuration does not support the factory defaults, verify the
following parameters using the addr command:
•
•
•
The Broadcast Address
The Subnet Mask.
The load/dump Gateway Address (which must be specified if the
preferred load server host is located on another network or subnet).
•
The IP encapsulation type. Many systems have hardware Ethernet
interfaces that are IEEE 802.3 compliant, but very few actually do
802.3 IP packet encapsulation. Use the default, Ethernet, unless you
know absolutely that your LAN does 802.2/802.3 IP packet
encapsulation.
You can use the defaults for the name of the image file containing the
CSMIM-T1’s software and the address of the preferred load server host.
If the value for the image name is incorrect, the CSMIM-T1 cannot boot.
Correct the name using the image command. If the address for the
preferred load server host is incorrect, the boot takes longer, since the
CSMIM-T1 has to broadcast for a host. Correct the load host’s address
using the addr command.
Confirm that the CSMIM-T1 boot parameters are correct by using the
appropriate ROM Monitor commands. Modify any boot parameters that
are incorrect or missing. Boot the CSMIM-T1 either by entering the boot
command at the console, or by holding down the SET UP button until the
STAT LED blinks rapidly, and then releasing.
CSMIM-T1 Hardware Installation Guide
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
5.3.2.1 Load Server Host Not Responding
The CSMIM-T1 can boot from one of the following hosts acting as a load
server host:
•
•
•
•
A UNIX host on the network
Another CSMIM-T1
A VAX VMS load server host
Any host (UNIX or non-UNIX) using tftp.
The following subsections discuss troubleshooting for some of these load
server hosts.
5.3.2.2 UNIX Host on the LAN
When troubleshooting a UNIX host on the LAN, make sure that:
•
•
The host is booted and functioning properly.
The host can communicate with other network nodes using standard
UNIX networking features and utilities.
•
•
All CSMIM-T1 software is installed properly on the host. See the
Software Installation Notes that come with the CSMIM-T1 software
release.
The erpcd daemon or tftp server, which loads the operational image
to the CSMIM-T1, is running.
In test mode, both the CSMIM-T1 and erpcd on the load server host
display boot progress reports. The CSMIM-T1 displays its reports on the
console; erpcd displays its reports on the UNIX terminal that invokes test
mode. To view the test reports, do the following:
1. To place erpcd on the load server host into test mode, kill the erpcd
program (requires superuser privileges) and restart it using the –D
option:
# /etc/erpcd –D5
2. To place the CSMIM-T1 into test mode, hold down the SET UP button
for 3 seconds. (This resets the module, so warn users before you do it.)
Then enter:
Console monitor:: boot -v
5-14
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOT Failures
When the CSMIM-T1 boots in test mode, the console displays the load
server host’s Internet address, and indicates whether it receives a response
to its Open File Request and to any of its Read File Requests. The host’s
progress report indicates receipt of any File Server Requests and its
responses to such requests. The host displays erpc_return 0 if it
successfully receives a request and is sending out an affirmative response.
If any CSMIM-T1-related files are missing or cannot be installed, contact
technical support (see Getting Help section in Preface).
A PC host running the UNIX operating system has the erpcd daemon
(provided with the distribution and installed in /usr/annex) running in the
background on the PC. Set the CSMIM-T1 and the erpcd on the load host
into test mode:
1. For erpcd on the load server host, as superuser, kill the erpcd program
and restart it using the –D option:
# /usr/annex/erpcd -D5
2. On the CSMIM-T1, hold down the SET UP button for 3 seconds to
enter the SET UP mode. Then enter:
monitor:: boot -v
5.3.2.3 Another CSMIM-T1
When troubleshooting a CSMIM-T1 configured as a load server host:
1. Use the CLI telnet command to access the unit and verify that it is up
and running.
2. Communicate with the unit on the Ethernet using the superuser CLI
ping command.
3. Verify the unit’s configuration using na.
The Annex Network Administrator’s Guide provides more information on
these commands.
A CSMIM-T1 that has been reconfigured as a load server host, but not
rebooted, cannot boot another CSMIM-T1 on the network. Rebooting the
CSMIM-T1 load server host ensures that the parameters are set.
CSMIM-T1 Hardware Installation Guide
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
5.3.2.4 VAX VMS Load Host on the LAN
If the installation was successful and the NCP CIRCUIT SERVICE is
enabled, but the CSMIM-T1 still fails to boot, performing the following
steps may locate your problem:
1. Make sure that the file CSMIM-T1 OPER_46_ENET.SYS is in the
directory MOM$LOAD and the file protection allows reading.
2. Enter the system manager account and enable console logging to see
the MOP boot requests, as in the following example:
$reply/enable
$
%%%%%%%% OPCOM 23-DEC-1994 08:3.37 %%%%%%%%
Operator_NTA2: has been enabled, username TOPAZ
$
$
%%%%%%%% OPCOM 23-DEC-1994 08:0.49 %%%%%%%%
Operator status for operator _NTA2:
CENTRAL, PRINTER, TAPES, DISKS, DEVICES, CARDS, NETWORK,
CLUSTER, SECURITY, LICENSE, OPER1, OPER2, OPER3, OPER4,
OPER5, OPER6, OPER7, OPER8, OPER9, OPER10, OPER11, OPER12
WARNING
$
$
%%%%%%%% opcom 23-DEC-1994 08:03:43.55 %%%%%%%%
Message from user DECNET
DECnet event 0.3, automatic line service
From node 1.69 (BINGO), 23-DEC-1994 08.03.43.52
Circuit SVA-0, Load, requested, Node =2.69 (BART)
File = MOM$SYSTEM_SOFTID:OPER_46_ENET.SYS, Operating
System
Ethernet address = 00-80-2D-00-1A-DE
$
%%%%%%%% opcom 23-DEC-1994 08:03:50.55 %%%%%%%%
Message from user DECNET
DECnet event 0.3, automatic line service
From node 1.69 (BINGO), 23-DEC-1994 08.03.50.52
Circuit SVA-0, Load, Successful, Node =2.69 (BART)
File = MOM$SYSTEM_SOFTID:OPER_46_ENET.SYS, Operating
System
Ethernet address = 00-80-2D-00-1A-DE
5-16
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CSMIM-T1 Dumps
5.4
CSMIM-T1 DUMPS
The CSMIM-T1 dumps its memory image to a host running load server
software when certain software or hardware events occur. Table 5-9
shows the LED states during a dump.
Dump files are generated for use by technical support
personnel only.
NOTE
Events that trigger CSMIM-T1 dumps are:
•
•
•
•
Non-recoverable hardware or software errors.
Software fails to reset the CSMIM-T1’s watchdog timer.
Software fails one or more internal consistency checks.
Hardware detects an internal fault.
Table 5-9 CSMIM-T1 LED States During a Dump
STAT
Green
ATTN
Amber
TRAF
Green
Activity
Dump
●
●
■
Key:
●
■
On continuously.
Flashing irregularly.
The CSMIM-T1 sends a dump file to a preferred load dump host. If you
do not define this host by specifying an address, the CSMIM-T1
broadcasts a request and dumps to the first host that responds.
The CSMIM-T1 sends a dump to the /usr/spool/erpcd/bfs directory on
the dump host. The /usr/spool/erpcd/bfs directory is a default pathname
and can be changed. The receiving CSMIM-T1 assigns a unique file name
for each device that it receives a dump from but not for each crash dump.
CSMIM-T1 Hardware Installation Guide
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting Procedures
Rename any crash dumps that you want to save. The
CSMIM-T1 overwrites crash dumps.
NOTE
The assigned name depends on the number of characters per file name
that the dump host supports. For hosts supporting file names longer than
14 characters (e.g., BSD hosts), dump files are named dump.addr. The
file extension addr is the CSMIM-T1’s IP address.
For hosts that limit file names to 14 characters (e.g., System V hosts), a
dump creates two additional directories under /usr/spool/erpcd/bfs. The
name of the first directory is dump; the second directory uses the
CSMIM-T1’s IP network address as its name. The dump file uses the
CSMIM-T1’s IP host address as its name.
\
The tftp dump names are user-defined. If a name is not
specified, the CSMIM-T1 uses the bfs convention.
NOTE
Each dump file contains a complete image of the CSMIM-T1 RAM
memory and hardware state. The amount of space required for a dump file
varies according to the port configuration. The ROM Monitor config
command displays the amount of memory for the CSMIM-T1.
Table 5-10 shows sample dump file names. All pathnames are relative to
the file /usr/spool/erpcd/bfs.
Table 5-10 CSMIM-T1 Dump File Naming Conventions
CSMIM-T1
Address
Network BSD
Address Filename
System V
Pathname
63.0.0.75
63
dump.63.0.0.75
dump.131.140.23.1
dump/63/0.0.75
131.140.23.1
195.46.2.15
131.140
dump/131.140/23.1
dump/195.46.2/15
195.46.2 dump.195.46.2.15
5-18
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6
MODEM GUIDE
6.1
GENERAL
The CSMIM-T1 uses 24 high performance, error-correcting, V.34 internal
modems. They are fully compatible with V.FC (V.Fast Class) modems and
offer support for cellular operations.
Under optimum conditions, the modems reach a maximum serial-port
speed of 115,200 bps. They support V.42bis data compression, and use
Hayes Smartmodem AT and V.25bis command sets, with enhancements
for maximum flexibility. The modems achieve error-free performance
through the Microcom Networking Protocol (MNP) and V.42
error-correction protocol standards. They offer MNP Class 10 with
Adverse Channel Enhancements (ACE). MNP 10 includes:
•
•
•
•
Multiple connection attempts during auto-reliable link negotiation
Negotiated speed upshifts
Aggressive adaptive packet assembly
Dynamic Transmit Level Adjustment
CSMIM-T1 Hardware Installation Guide
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
6.2
FEATURES
The modems have the following features:
•
•
•
•
•
•
•
•
ITU-T standards: V.21, V.22, V.22bis, V.23, V.32, V.32bis, and V.34
Compatibility with Rockwell International’s V.FC protocol
Serial-port speeds of up to 115,200 bps
Bell 212A and Bell 103 protocol standards
V.42 error correction, including LAPM and MNP2 through 4
V.42bis compression as well as MNP5 Data Compression
MNP Class 10 Adverse Channel Enhancements (ACE)
14,400 Class 1 Group III fax send and receive operation through fax
and data communications software.
•
•
•
Enhanced operation in cellular environments
V25bis asynchronous operation
Multi-protocol auto-answering to answer incoming calls
automatically using various modulation protocols
•
•
•
•
Trellis coded modulation for forward error correction
Near- and far-end echo cancellation
Automatic power-up diagnostics
Asynchronous 11-bit character support.
6-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the AT Command Set
6.3
USING THE AT COMMAND SET
Each command line must begin with the characters AT (the ATtention
code). Both characters of the attention code must be in either upper case
or lower case, but you may type the commands in any combination.
Type commands after the OK response. The modem ignores spaces
between characters. If you make a mistake, press the backspace key
(Cntrl-H) and type the correct character. To make a command take effect,
press <Enter>.
You can enter an AT command at any supported serial-port speed up to
115,200 bps. Your modem automatically adjusts to the connection and
command speeds (autobauds) up to 19,200 bps. After you enter an AT at
any speed up to 19,200 bps, you can enter other commands at a new
serial-port speed at any time. If you enter a command at 38,400; 57,600;
or 115,200 bps, the serial port locks at that speed.
To unlock the serial-port speed and change to another speed:
•
•
type AT$Bn (n is any supported serial-port speed), OR
type AT%U <Enter> to unlock the serial-port speed, then enter an AT
at the new speed.
•
Now enter an AT at the new speed.
The serial-port speed defaults to 115,200 bps.
NOTE
CSMIM-T1 Hardware Installation Guide
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
6.3.1
Key AT Command Factory Defaults
Table 6-1 Key AT Command Factory Defaults
AT
Title Default
$Bn
%Bn
%Cn
&Cn
D
Serial-Port Bps Rate
Modem-Port Bps Rate
Compression Control
Serial-Port DCD Control
Dial
115,200
28,800
3 (MNP 5 & V.42bis)
1 (On after connect message)
T (Tone dial)
&Dn
En
DTR Control
2
Command Echo
1 (echo to local DTE)
&F
Restore Factory Defaults
Hang Up
none
H
none
*Hn
\Jn
Link Negotiation Speed
Bps Rate Adjust
0 (at highest speed)
0 (disabled)
1 (enabled)
%Ln
)Mn
@Mn
\Nn
On
Speed Matching
Cellular Power Level Adjustment
Select Cellular Transmit Level
Operating Mode
0 (For central site modems)
0 (-26 dBm)
3 (auto-reliable)
none
Enter Connect State and Retrain
Quiet
Qn
0 (result code output)
3 (bi-directional hardware)
none
\Qn
%Rn
Sn?
\S
Serial-Port Flow Control
Read All Registers
Read Configuration Register
Read On-line Status
Tone Dial
none
none
T
none
:Tn?
Read Configuration Register
none
6-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the AT Command Set
Vn
Result Code Form
1 (long form)
\Vn
Error Correction Result Code Form 2 (long form)
%V
&Wn
*Wn
Display Modem Firmware Version
Store Current Configuration
Store Complete Configuration
none
0
0
You are ready to establish a connection as either a dialing modem or an
auto-answer modem. For tone dialing, type:
ATDT <telephone number> <Enter>
The modem automatically answers calls on the first ring if DTR is
present.
Hanging Up
To hang up, use one of these methods:
•
Pause 1 second. Then type +++ to enter command state. Type ATH
<Enter> to hang up OR
•
Lower DTR with your communications program when &D2 or &D3
is set.
See Chapter 7, AT Commands and Registers, for detailed information
about any of the commands mentioned above.
6.3.2
Establishing 11-Bit Data Connections
By default, your modem port passes 10-bit characters during MNP or
LAPM connections.
In a normal or direct connection, those bit and parity settings on the
originating and remote modems must match for data to transfer
accurately. The serial-port parity determines the number of data bits set
during a direct connection.
The -E command determines the characters handled on the modem port
during a normal connection - unless the modem falls back from a reliable
connection (either \N3 or \N5 is set) to a normal connection. In this case,
the remote modem port must be set for a data length of 10 bits.
CSMIM-T1 Hardware Installation Guide
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
6.3.3
V.32bis Cellular Connections Using AT
Commands
The internal V.34 modems may be set up in different ways to operate over
a cellular telephone network. The following are typical setups that might
be used.
•
•
Your modem supports cellular operation from 1200 to 14,400 bps.
MNP Class 10 is not active for connections below 1200 bps.
6.3.3.1 Universal Cellular Setup
Land-side modem - AT&F (factory defaults)
This allows the land side to make data connections with land based and
cellular based modems without reducing maximum connection speeds.
Connections over most land lines can reach 14,400 bps modem speeds
between V.32bis modems, and 28,800 bps between V.34 modems. MNP
10 cellular connections occur at the highest speed the modems determine
they can support for each cellular connection. If the land-side modem will
only make cellular connections, we recommend setting \N2.
6.3.3.2 MNP 10 V.32bis Quick Connect Cellular Only
Setup
Land-side modem - AT&F\N2)M1
This forces MNP connections to all modems and MNP 10 cellular
connections to all MNP 10 modems.
Additional connection speed enhancements
In addition, registers :T17 and :T26 can shorten connect times. We
suggest changing these registers only after making some cellular
connections with these registers set to defaults. Using them may limit the
modem’s ability to connect over noisy lines.
6-6
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Modulation Protocols
6.4
MODULATION PROTOCOLS
Using Multi-Protocol Auto-Answer
The multi-protocol auto-answer feature allows auto-answer of incoming
calls from modems using any of the following protocols: V.34, V.FC,
V.32bis, V.32, V.22bis, V.22 (1200 bps only), V.21, V.23 half-duplex, Bell
212A, and Bell 103.
To enable this feature for V.23 half-duplex connections, set :T2
to a value greater than 0. We recommend setting :T2=20 when
NOTE
falling back to a V.23 half-duplex connection.
V.34 and V.FC
Basically, V.34 is the new ITU-T standard that formalizes the temporary
V.FC (V.fast Class) protocol. It has all the features of our V.FC modems,
plus the additional commands described in Appendix A.You can enjoy the
same 28,800 bps connect speeds, high data integrity, and throughputs up
to 115,200 bps.
One obvious improvement is “handshaking” between V.34 modems.
Connection negotiation will take about 5 seconds instead of up to 15
seconds and will use a few new tones. V.34 includes the new V.8
handshake standard, and adds line probing and fast negotiation between
two modems that support it. If the other modem does not include V.8,
your modem will proceed with the previous negotiation methods. Expect
these faster negotiations as V.34 modems become common.
You should also see better adaptations to phone lines. In V.34
connections, our modems stay in that modulation from 2,400 through
28,800 bps. The V.FC range is 14,000 through 28,800 bps. If line
conditions require fallback or permit fall-forward, two V.34 modems can
perform either easily.
Finally, while not all V.34 modems support V.FC connections, ours do.
That means you can expect continued high-speed connections to over 1
million V.FC modems from over 120 vendors. By default, your modem
will start a negotiation at V.34 and if it can’t get one, connect at V.FC,
V.32bis and V.32 in that order - permitting the highest speed connections
with other modems.
CSMIM-T1 Hardware Installation Guide
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
V.32 and V.32bis Protocols
The ITU-T V.32 protocol is for full-duplex data transfer over general
switched telephone networks at 9,600 and 4,800 bps. V.32 employs echo
cancellation and trellis coded modulation.
The ITU-T V.32bis specification enhances V.32 by adding 14,400, 12,000,
and 7,200 bps speeds and special rate sequences to shorten speed
upshifting and downshifting.
V.23 Protocol 1,200 Bps Half-Duplex Operation
The modem supports one V.23 mode - main channel half duplex at 1200
bps.V.23 half-duplex operation is available only for direct and normal
connections. For V.23 half-duplex connections, set %F3 on both
modems.
The features described in this manual apply to V.23 operation, except that
the modem does not support:
•
•
V.54 digital and analog loopback.
MNP and LAPM connections.
Table 6-2 Configuring the Modems for V.23 connections
When %F1, %F2, or %F3 is set for V.23 connections:
Protocol
Command
V.23 (1200 bps half duplex)
%F3
When you configure your modem for V.23 operation by setting
the %Fn command to a value other than 0, this disables other
modulation protocols.
NOTES
When the modem establishes a V.23 half-duplex connection it
displays CONNECT V.23 HDX.
When the originate modem is set to normal mode, you must
send a few characters to the answer modem before the
originate modem can fall back to a V.23 half-duplex
connection.
6-8
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Modulation Protocols
V.22 and V.22bis Protocols
V.22 protocol is used for 1200 bps and 600 bps full-duplex connections.
The version of V.22 your modem supports is Alternative B.
V.22bis protocol enhances V.22 by adding 2400 bps full-duplex
connections.
For V.22 at 600 bps, both modems must be set to 600 bps.
NOTE
V.21 Protocol
V.21 protocol is used for 300 bps full-duplex connections. The features
described in this manual apply to V.21 operation except that your modem
does not support:
•
•
V.54 digital and analog loopback.
LAPM connections.
When your modem establishes a V.21 connection, it displays
CONNECT V.21/REL - MNP. With a normal or direct V.21
connection, the message is CONNECT.
NOTE
Bell 212A Protocol
Bell 212A protocol is for 1200 bps full-duplex connections.
CSMIM-T1 Hardware Installation Guide
6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
Bell 103 Protocol
Bell 103 protocol is for 300 bps full-duplex connections. The features
described in this guide apply to Bell 103 operation except that your
modem does not support:
•
•
Digital (loop 1A) and analog (V.54 loop 3) loopback.
LAPM connections.
When your modem establishes a reliable Bell 103 connection,
it displays CONNECT 103/REL - MNP. For a normal or direct
Bell 103 connection, the message is CONNECT.
NOTE
6.4.1
Protocol Configuration Command Settings
When you send an AT string to the modem, it adjusts modem-port speed
automatically to match the AT speed. Use %G1 to disable this feature.
With %G1 set, you can change the modem speed with %Bn (where n is
the new modem speed) and %Fn.
This section lists settings to configure the modem for each mode and
protocol. Modem connection speeds are in parentheses.
Table 6-3 Configuring the Modem with %F0 Set
Protocol
Issue %G0:
Issue %G1:
V.21 (75-300 bps)
B0 at 300 bps
B1 at 300 bps
at 600 bps
B0%B300
B1%B300
%B600
Bell 103 (75-300 bps)
V.22 (600 bps)
V.22 (1200 bps)
B0 at 1200 bps
B1 at 1200 bps
at 2400 bps
at 4800 bps
at 7200 bps
at 9600 bps
at 12000 bps
B0%B1200
B1%B1200
%B2400
%B4800
%B7200
%B9600
%B12000
Bell 212A (1200 bps)
V.34/V.22bis (2400 bps)
V.34/V.32bis/V.32 (4800 bps)
V.34/V.32bis (7200 bps)
V.34/V.32bis/V.32 (9600 bps)
V.34/V.32bis (12000 bps)
6-10
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Modulation Protocols
V.34/V.32bis (14400 bps)
V.34/V.FC (14400 bps)
V.34/V.FC (16800 bps)
V.34/V.FC (19200 bps)
V.34/V.FC (21600 bps)
V.34/V.FC (24000 bps)
V.34/V.FC (26400 bps)
V.34/V.FC (28800 bps)
at 14400 bps
at 14400 bps
at 16800 bps
at 19200 bps
at 21600 bps
at 24000 bps
at 26400 bps
at 28800 bps
%B14400
%BV14400
%B16800
%B19200
%B21600
%B24000
%B26400
%B28800
For the highest possible throughput available, set the
modem-port speed by typing AT%G1%Bn (where n equals the
desired speed).
NOTE
6.4.2
Speed and Protocol Connection Matrices
The following tables show the possible speed and protocol combinations
for modem connections. They also illustrate the action of an answer
modem set to use multi-mode answering.
CSMIM-T1 Hardware Installation Guide
6-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
Table 6-4 Modem Speed and Protocol Combinations
Mode Setting
on
Originating
Modem
Mode Setting on Answer Modem
V.22[b] V.22[a] V.22bis V.32
V.32bis V.34/V.FC
V.34/V.FC
(14400-28800)
—
—
—
—
V.22bis V.32
V.22[a] V.22bis V.32
V.22[a] V.22bis V.32
V.32bis V.34/V.FC
V.34/V.32bis
(4800-14400)
V.32bis V.34/V.32bis
V.34/V.32
(4800-9600)
V.32
V.34/V.32
V.34/V.22bis
(2400)
V.22[a] V.22bis V.22bis V.22bis V.34/V.22bis
V.22[a] V.22[a] V.22[a] V.22[a] V.22[a]
V.22[a] (1200)
V.22[b] (600)
—
V.22[b]
—
—
—
—
—
—
V.23[c]
V.23[c] V.23[c] V.23[c] V.23[c]
V.23[c]
(half-duplex)
V.21(75-300)
—
V.21
V.21
V.21
V.21
V.21
Bell212A (1200) —
V.22[a] V.22[a] V.22[a] V.22[a] V.22[a]
Bell103 Bell103 Bell103 Bell103 Bell 103
Bell103 (300)
—
6-12
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Modulation Protocols
Table 6-5 Modem Speed and Protocol Combinations
Mode Setting on Answer Modem
Mode Setting on
Originating Modem
Bell103
Bell212A
V.21
V.23[c]
V.34/V.FC (2400-28800)
Bell103
Bell212A
Bell212A
Bell212A
Bell212A
Bell212A
—
—
—
—
—
—
—
—
V.21
—
—
—
V.34/V.32bis (4800-14400) Bell103
—
V.34/V.32 (4800-9600)
V.34/V.22bis (2400)
V.22[a] (1200)
Bell103
Bell103
Bell103
—
—
—
—
V.22[b] (600)
—
V.23[c] (half-duplex)
V.21(75-300)
—
—
V.23[c]
—
—
V.21
Bell212A (1200)
Bell103 (300)
Bell212A
Bell103
Bell212A
Bell103
—
—
For operations at V.22 600 bps, both modems must be set to
600.
NOTE
CSMIM-T1 Hardware Installation Guide
6-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
6.5
ERROR CORRECTION
MNP Classes
The modem provides MNP Class 10 and supports MNP Class 5 data
compression. It is compatible with all MNP products. Its enhanced MNP
service is completely transparent to the user.
Class 10: Adverse Channel Enhancements (ACE) optimizes performance
under poor line conditions. Class 10 continues to provide compatibility
with non-MNP modems. It improves initial connection success rate by
making multiple negotiation attempts when configured for auto-reliable
mode. It uses Dynamic Transmit Level Adjustment to calculate optimal
transmit levels automatically to compensate for cellular phone signal
distortion. It lets the user configure the modem to negotiate the link at a
low-speed modulation, then upshift to a higher speed after negotiation. It
improves link performance during adverse channel conditions by
aggressive Adaptive Packet Assembly. It maximizes throughput by
continuously monitoring line quality and link performance, and
dynamically upshifting or downshifting to the optimum modulation
speed.
Class 5 provides data compression, which combined with MNP
Class 4 allows throughput of almost twice the connection speed.
Class 5 dynamically adjusts to the type of data being transmitted for
maximum compression efficiency.
6-14
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Correction
Other Classes of MNP
MNP Class 2 uses standard asynchronous framing techniques for data
transmission and error correction. Because of this protocol overhead, the
actual throughput is less than the bps rate of the modem.
MNP Class 3 uses synchronous framing techniques. Removing start and
stop bits associated with each character prior to transmitting results in a
20% performance increase over Class 2. Thus, actual throughput is
greater than the modem’s bps rate.
MNP Class 4 uses synchronous framing techniques plus improvements
developed by Microcom Adaptive Packet Assembly and Optimized Data
Phase. These enhancements result in better performance for all types of
connections.
Adaptive Packet Assembly automatically adjusts the size of the data
packets based on the quality of the telephone line. When the line quality is
good and there are few retransmissions, the modem increases the packet
size. When the line quality is poor and retransmissions are frequent, the
size of the packet decreases in order to maintain high throughput during
error correction under poor conditions.
Optimized Data Phase is the redesign of the MNP protocol header that
reduces the number of overhead bytes per data packet. For example,
modems operating at Class 4 service transmit data at 2,900 bps.
MNP Class 6 allows half-duplex, fast-train, high-speed reliable
connections with other MNP Class 6 modems at speeds of 4,800 to
9,600 bps.
Universal Link Negotiation allows the modem to automatically connect
with other MNP modems at the highest common speed and protocol.
Statistical Duplexing adjusts the line bandwidth and data traffic flow
during reliable connections to achieve maximum throughput.
MNP Class 7 provides Enhanced Data Compression, which combined
with Class 4 allows throughput of more than twice the connection speed.
MNP Class 7 Enhanced Data Compression not only dynamically adjusts
to the type of data being transmitted, but allows for the probability of
character frequency, for superior compression efficiency.
MNP Class 9 includes enhanced Universal Link Negotiation.
CSMIM-T1 Hardware Installation Guide
6-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
6.6
DIAGNOSTICS
The modem’s diagnostic capabilities verify its performance and can
isolate the source of a communications problem. If a problem exists, test
all components of the communications path, including the data cable and
all connectors.
The modem must be in normal or direct mode for loopback
tests. It does not support these tests in Bell 103, V.13, V.21, or
NOTE
V.23 mode. The modem supports all loopback tests 1,200 bps
or higher.
6.6.1
Power-Up Diagnostics
Power-up diagnostics test the program checksum, RAM memory, and
components on the modem board each time you power up the modem.
Performing a Power-Up Diagnostic Test
To perform a power-up diagnostic test, enter the following at the
command prompt:
AT$D <Enter>
6.6.2
Local Analog Loopback with Self-Test
Local Analog Loopback with Self-Test tests the local serial port. The
modem sends itself a test data sequence and then verifies the data to make
sure that it receives them correctly.
Using Commands to Perform a Local Analog Loopback with Self-Test
To initiate a Local Analog Loopback with Self-Test, type AT&T8
<Enter>. When the test finishes, the screen displays a three-digit number
that represents the number of errors. For example:
AT&T8
(no display during test)
000
OK
The test continues until the time set with register S18 runs out, or until the
test is terminated by typing AT&T0 <Enter>, or ATH <Enter> to end the
test and hang up.
6-16
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics
6.6.3
Local Analog Loopback
Local Analog Loopback tests the local serial port and the local computer.
This test requires you to type a sequence of characters at your computer.
The modem then sends these characters back to your computer. You
initiate a Local Analog Loopback test by using the &T1 command.
Using Commands to Perform a Local Analog Loopback
To initiate a Local Analog Loopback:
1. Type: AT&T1<Enter> (must be the last command on the line).
2. Type a sequence of characters.
The characters on your display should match exactly the characters you
type. This test mode continues for the time set with register S18, or until
you manually terminate the test. To manually end the test, enter command
state and type: AT&T0<Enter> To end the test and hang up, type: ATH
<Enter>.
6.6.4
Remote Digital Loopback with Self-Test
Remote Digital Loopback with Self-Test tests the remote modem port, the
telephone line, and the local serial and modem ports. When the modem is
set to Remote Digital Loopback with Self-Test, it sends the remote
modem a special test data sequence, and the remote modem echoes this
data back to your modem.
To initiate a Remote Digital Loopback with Self-Test:
1. Dial the number of a remote system configured to accept a Remote
Digital Loopback request.
2. When the modems connect, return to command state and type:
AT&T7 <Enter>.
When the test is complete, the screen displays a 3-digit number that
represents the number of errors. For example:
AT&T7
(no display during test)
000
OK
The test continues for the time set with register S18 or until you terminate
the test by typing AT&T0 <Enter>, or ATH <Enter> to end the test and
hang up.
CSMIM-T1 Hardware Installation Guide
6-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
6.6.5
Remote Digital Loopback
Remote Digital Loopback tests the remote modem port, the telephone
line, the local serial and modem ports, and the local computer. This test
requires you to type a sequence of characters at your computer. The
modem then sends these characters to the remote modem, which echoes
them back to your modem.
Initiate a Remote Digital Loopback by using the &T6 command.
Using Commands to Perform a Remote Digital Loopback
To initiate a Remote Digital Loopback:
1. Dial the number of a remote system configured to accept a Remote
Digital Loopback request.
2. When the modems connect, return to the command state and type:
B <Enter>.
3. Type a sequence of characters.
The characters echoed on your display should match exactly the
characters you typed. The test continues for the time set with register S18,
or until you manually terminate the test. To manually end the test, enter
command state and type: AT&T0 <Enter>.
To end the test and hang up, type: ATH <Enter>
6.6.6
Local Digital Loopback
Local Digital Loopback allows the modem to loop back data to the remote
modem. It tests the remote computer, the remote modem and serial ports,
the telephone line, and the local modem port. You initiate a Local Digital
Loopback by using the &T3 command.
Using Commands to Perform a Local Digital Loopback
To initiate a Local Digital Loopback:
1. Dial the number of a remote system.
2. When the modems connect, return to the command state and type:
AT&T3 <Enter>.
6-18
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics
The operator of the remote system now types a sequence of characters.
You do not see any characters on your display while your modem echoes
the characters typed by the operator of the remote modem back to the
remote computer. The test continues for the time set with register S18. If
you do not use register S18, the operator of the remote modem must hang
up or call you on another telephone line to tell you when the test is over.
To manually end the test, enter command state and type: AT&T0
<Enter>. To end the test and hang up, type: ATH <Enter>.
6.6.7
Respond to Remote Digital Loopback
The Respond to Remote Digital Loopback command configures your
modem to accept a request from a remote modem to engage in a Remote
Digital Loopback or a Remote Digital Loopback with Self-Test. To
configure the modem to accept a remote digital loopback request, at the
command prompt type: AT&T4 <Enter>.
To configure the modem to ignore a remote digital loopback request, type:
AT&T5 <Enter>.
6.6.8
Automatically Terminating a Test: Register S18
To configure the modem to terminate a test automatically after a specified
time, change the value of register S18. Register S18 determines the
duration of a diagnostic test. The factory default setting is 0 seconds,
which disables the timer and causes tests to continue indefinitely until you
cancel them. You can set this register to terminate tests after 1 to 255
seconds.
CSMIM-T1 Hardware Installation Guide
6-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
6.7
RESULT CODES
The modem can display these result codes when it attempts to establish a
connection. See also Chapter 7, AT Commands and Registers for
descriptions of the commands.
6.7.1
Connection Result Code Tables
The tables use the abbreviations: rel (reliable) and non-rel (non reliable).
Table 6-6 shows the short and long form result codes, excluding
connection result codes whose form depends on the \V, W, and -M
commands.
Table 6-6 Result Codes
Short Form
Long Form
0
1
2
3
4
6
7
8
5
OK
CONNECT
RING
NO CARRIER
ERROR
NO DIALTONE
BUSY
NO ANSWER
NO PROMPT TONE
Display of these call progress monitoring result codes depends
on the setting of the X command.
NOTE
6-20
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Result Codes
Table 6-7 Long Form Connect Result Codes
ATV1-M0W0 or ATV1-M0W1 Report DTE Speed
DTE Speed (bps) Non-rel
\V0 rel
\V1 rel, \V2 rel
4
\V3 rel, \V4 rel, \V5 rel
75
75
75/REL
300
300
300/REL
600
600
600/REL
1200
2400
4800
9600
19,200
38,400
57,600
115,200
1200
2400
4800
9600
19,200
38,400
57,600
115,200
1200/REL
2400/REL
4800/REL
9600/REL
19,200/REL
38,400/REL
57,600/REL
115,200/REL
CSMIM-T1 Hardware Installation Guide
6-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
Table 6-8 Long Form Connect Result Codes
ATV1-M0W2
Report Modulation Speed
Modulation
Speed (bps) Non-rel
\V1 rel
\V2 rel
\V3 rel
\V4 rel
\V5 rel
1
1
4
\V0 rel
2&3
V.21
300
—
V.21/REL
103/REL
—
V.21/REL
103/REL
—
2
Bell 103
300
—
3
V.23 half-duplex
V.22
1200
V.23 HDX
3
600
600
600/REL
1200/REL
2400/REL
9600/REL
9600/REL
9600/REL
9600/REL
600/REL
1200/REL
2400/REL
4800/REL
7200/REL
9600/REL
12000/REL
V.22 \Bell 212A
V.34/V.22bis
V.34/V.32
V.34/V.32bis
V.34/V.32
V.34/V.32bis
V.34/V.32bis
V.34/V.FC
V.34/V.FC
V.34/V.FC
V.34/V.FC
V.34/V.FC
V.34/V.FC
V.34/V.FC
1200
1200
2400
2400
4800
4800
7200
7200
9600
9600
12,000
14,400
14,400
16,800
19,200
21,600
24,000
26,400
28,800
12,000
14,400
14,400
16,800
19,200
21,600
24,000
26,400
28,800
14,400/REL 14,400/REL
14,400/REL 14,400/REL
16,800/REL 16,800/REL
19,200/REL 19,200/REL
21,600/REL 21,600/REL
24,000/REL 24,000/REL
26,400/REL 26,400/REL
28,800/REL 28,800/REL
1
If \V2 or \V4 is set and a reliable link is established, the message displays as
one of the following formats: CONNECT <speed>/REL - MNP or CONNECT
<speed>/REL - LAPM or CONNECT <speed>/REL - CELLULAR.
2
In non-reliable V.21 or Bell 103 connections, the message displays as
CONNECT.
3
Not supported in synchronous mode.
6-22
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Result Codes
4
If \V5 is set, the message displays as one of the following formats:
CONNECT <speed>/<modulation>REL -CELLULAR,
CONNECT <speed>/<modulation>REL - LAPM, or
CONNECT <speed>/<modulation>REL - MNP, with the modulation /V.34,
/V.FC, /V.32, /V.22, or /FSK
Table 6-9 Short Form (Numeric Connect Result Code)
ATV0W0 or ATV0W1 Report DTE speed
DTE Speed \V0
\V1 rel
\V3
(bps)
\V1 non-rel \V2 rel
\V2 non-rel \V4 rel
\V4 non-rel \V5 rel
\V5 non-rel
75
1
20
20
21
22
23
31
33
37
39
43
73
1
300
1
1
600
9
5
1200
2400
4800
9600
19,200
38,400
57,600
115,200
5
5
10
30
32
36
38
42
72
10
11
12
14
28
29
30
CSMIM-T1 Hardware Installation Guide
6-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Modem Guide
Table 6-10 ATV0W2 Report Modulation Speed
ATV0W2 Report Modulation Speed
Modulation
Speed
(bps)
\V0
\V1 rel
\V3
\V4 rel
\V5 rel
\V1 non-rel \V2 \V2rel
non-rel \V4
non-rel \V5
non-rel
V.21 or Bell 103
V.23 half-duplex
V.22
300
11
20
—
11
20
—
1200
600
51
51
91
21
22
23
31
33
33
33
35
35
61
37
63
65
67
69
51
21
22
23
31
41
33
45
35
35
61
37
63
65
67
69
V.22 or Bell 212A 1200
5
5
V.34/V.22bis
V.34/V.32
2400
10
30
402
32
442
342
342
60
36
62
64
66
68
10
11
24
12
25
13
13
13
14
13
13
13
13
4800
V.34/V.32bis
V.34/V.32
7200
9600
V.34/V.32bis
V.34/V.32bis
V.34/V.FC
V.34/V.FC
V.34/V.FC
V.34/V.FC
V.34/V.FC
V.34/V.FC
V.34/V.FC
12,000
14,400
14,400
16,800
19,200
21,600
24,000
26,400
28,800
1 Not Supported in synchronous mode
2 In synchronous mode or when \V0 is set , the following numeric codes display:
14400 bps=34; 12000 bps = 44; 7200 bps = 40.
6-24
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 7
AT COMMANDS AND REGISTERS
This chapter contains the following sections:
•
•
•
•
•
The Command Set
Entering Commands
Issuing AT Commands at any Speed
Command Descriptions
Register Descriptions
7.1
THE COMMAND SET
The modem responds to a superset of Hayes Smartmodem commands.
(Additional commands use the prefixes $, %, ), *, -, :, @, and \.) The
modem also stores configuration settings in a set of registers. These are
similar to the Hayes Smartmodem registers, although some have
enhanced modem features.
Factory defaults for commands and registers work with many
installations; you may never need to change the default
NOTE
settings.
7.1.1
Entering Commands
Each command line must begin with the characters AT (the ATtention
code). Both characters of the attention code must be in either upper case
or lower case, but you may type the commands in any combination.
Type commands after the OK response. The modem ignores spaces
between characters. If you make a mistake press the backspace key
( Cntrl-H ) and type the correct character. To make a command take effect,
press <Enter>.
CSMIM-T1 Hardware Installation Guide
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
7.1.1.1 Issuing AT Commands at any Speed
You can enter AT commands at any supported serial-port speed up to
115,200 bps. Your modem automatically adjusts to the connection and
command speeds (autobauds) up to 19,200 bps. Any time after you enter
an AT at any speed up to 19,200 bps, you can enter commands at a new
serial-port speed. If you enter a command at 38,400, 57,600, or 115,200
bps, the serial port locks at that speed. The serial-port default speed is
38,400 bps.
To unlock the serial-port speed and change to another speed:
•
Enter an AT$Bn command (where n is any supported serial-port
speed), or
•
type AT%U to unlock the serial-port speed, then enter an AT at the
new speed, or
•
with &D2, or &D3 set, lower then raise DTR.
7.2
COMMANDS
This section lists the modem AT commands in alphabetical order. A
command argument printed in bold is the default setting.
In most cases, you will not need to change the default setting.
NOTE
A/
A
Repeat Last Command
Re-executes the last command immediately. The A/ command is
not preceded by “AT” and not followed by <Enter>.
Answer
Forces the modem to go off hook in answer mode, regardless of
the value of register S0.
If result codes are enabled, your modem returns the result code
RING (long form) or 2 (short form) when it receives a call.
7-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
%An Auto-Reliable Fallback Character
Where n is an integer between 0 and 127 indicating an ASCII
character (Default is 0, auto-reliable fallback character disabled).
Sets the ASCII character recognized as the auto-reliable fallback
character on the answering modem. In auto-reliable mode, when
the modem encounters an incoming auto-reliable fallback
character from the remote system, it automatically switches to
normal mode and passes the character to the serial port.
Auto-reliable fallback character recognition stops if the modem
receives a SYN character (decimal 22).
Do not set n=63 or n=126. These settings interfere with V.42
negotiations.
!
CAUTION
With this command, \ N3 \ C2 must also be set.
NOTE
\An
Maximum MNP Block Size
\A0
\A1
\A2
\A3
Sets block size up to a maximum of 64 characters.
Sets block size up to a maximum of 128 characters.
Sets block size up to a maximum of 192 characters.
Sets block size up to a maximum of 256 characters.
Sets maximum block size for MNP stream link connections.
Bn
ITU-T/Bell Mode
B0
Uses ITU-T V.22 and V.21 standards at 1,200 and 300 bps.
Uses Bell 212A and 103 standards at 1,200 and 300 bps.
B1
$Bn
Serial-Port Bps Rate
Where n = 75; 300; 600; 1,200; 2,400; 4,800; 9,600; 19,200;
38,400; 57,600; 115,200 bps.
Sets the serial-port bps rate when issued.
CSMIM-T1 Hardware Installation Guide
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
%Bn Modem-Port Bps Rate
Where n = 75; 300; 600; 1,200; 2,400; 4,800; 7,200; 9,600;
12,000; 14,400; 16,800; 19,200; 21,600; 24,000; 26,400; 28,800
bps.
When you enter this locally, the modem-port bps rate is set.
Downshifting can still take place.
If %G0 is set, an AT issued locally causes the modem-port
speed to match the serial-port speed, regardless of any
NOTES
previous %B setting.
If %G1 is set, the modem speed is changed only when you
enter a %Bn command. Entering a %F1, %F2, or %F3 causes
a change to 1,200 bps.
\Bn
Transmit Break
Where n is an integer between 1 and 9 indicating the time (in
increments of 100 milliseconds) to send the Break. (Default is 300
milliseconds.) During a reliable link the Break always equals 300
milliseconds.
Transmits a Break to the remote system from command state. To
return to connect state, type: ATO <Enter> (See also \K.).
%Cn Compression Control
%C0 Disables data compression.
%C1 Enables MNP 5 Data Compression only.
%C2 Enables V.42bis compression only.
%C3 Enables both V.42bis and MNP 5 Data Compression. The modem
matches the capability of the remote modem
Determines whether the modem attempts to use data compression
during reliable connections. We recommend leaving this
command at its default (%C3). This allows the modem to
establish a reliable connection using either MNP 5 Data
Compression or V.42bis compression, depending on the
capability of the remote modem.
7-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
Setting this command to 1 or 2 restricts the modem to using either
MNP 5 Data Compression or V.42bis compression, respectively,
or else a non-compression connection results.
If the remote modem does not support data compression or has it
disabled, the modem can establish a connection without data
compression, regardless of the modem’s %C setting.
We recommend disabling bps rate adjust ( \ J0) for the most
throughput.
NOTES
With AT \ J1 set, when the modem establishes a reliable
connection at speeds between 4,800 and 16,800 bps, the serial
port adjusts to 9,600 bps. If the connection speed is 19,200 or
above, the serial port adjusts to 19,200 bps.
&Cn Serial-Port DCD Control
&C0 DCD always On.
&C1 DCD follows the state of the carrier from the remote system; DCD
turns On after the connect message.
&C2 DCD On except momentarily at disconnect.
Controls the Data Carrier Detect (DCD) signal on the serial port.
Use this command if your computer requires CD to be Off at
certain times. See also the \D command description.
The &C and \ D settings are ignored while connected in V.23
half-duplex direct mode (%F3) or ITU-T V.13 (&R2).
NOTE
Hardware flow control overrides the &C and \ D settings for
CTS operation. (See also \Q.)
@Cn CTS, DSR, and DCD Connect Message Control
@C0 CTS, DSR, and DCD go On after the connect message is sent.
@C1 CTS, DSR, and DCD go On before the connect message is sent.
Specifies whether CTS, DSR, and DCD go On before or after a
connect message. Use this command with :T14.
CSMIM-T1 Hardware Installation Guide
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
\Cn
Auto-Reliable Buffer
\C0
Does not buffer data during link negotiation. Switches to normal
or direct mode if no SYN character is detected within 3 seconds.
\C1
Buffers all data on the answering modem until it receives either
200 non-SYN characters or a SYN character within 3 seconds
(this delay is longer for modem speeds 300 or below). If it
receives 200 non-SYN characters, the modem switches to normal
mode and passes the data through to the serial port. If it detects a
SYN character within 3 seconds, it attempts to establish a reliable
connection. Otherwise, it switches to normal mode.
\C2
Does not buffer data on the answering modem. Switches to
normal mode upon receipt of a character defined by the AT%A
command and passes that character to the serial port.
Determines if the answering modem set to auto-reliable mode and
auto-answer buffers data from the remote modem during the 3
seconds when it tries to establish a reliable connection. When the
modem receives calls both from modems that support MNP and
from modems that do not, set \C2. This allows the modem to
switch to normal mode as soon as it detects a log-on character
(defined by %A) from a non-MNP caller. This eliminates the
3-second wait. (See the \N command description for more
information about auto-reliable and normal modes.)
For example, use %A to set the auto-reliable fallback character to
ASCII 13 (carriage return). Then set \C2\N3. Non-MNP callers
who connect and press to log on do not have to wait for the
3-second auto-reliable window to expire before data can pass.
When either \ C1 or \ C2 is set, reliable and normal connections
may result independent of bps rate adjust. However, when \C0
is set bps rate adjust affects the type of connection as follows:
NOTES
Reliable and direct connections may result when bps rate
adjust is On (\ J1).
Reliable and normal connections may result when bps rate
adjust is Off (\ J0).
When falling back to V.23 full duplex connections and either
\C1 or \C2 is set, reliable and normal connections may result
independent of the \W command.
7-6
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
D <dial string> Dial
Where <dial string> is a string of up to 98 characters. Do not type
< or >.Valid dial string characters are: 0-9, dial modifiers, and for
tone dialing A, B, C, D, #, and*. The modem ignores invalid
characters. Dial strings longer than 98 characters produce an error
message.
Dials a telephone number and attempts to establish a connection.
The Dial command must be the last one on a command line.
To cancel the Dial command, press any key or use your data
communications software to lower DTR (unless &D0 is set).
To dial the telephone number 011 22 555 1234, type:
ATD 011225551234 <Enter>
After disconnect, there is a 5-second delay before the modem
goes off hook in originate mode.
NOTE
Dial Modifiers
Dial modifiers allow you to add conditions to the telephone
number you dial. You can use several modifiers with the same
telephone number. Dial modifiers include:
^A
J
(Link Negotiation) Perform link negotiation at 4,800 bps for the
current connection only. (This dial modifier is equivalent to the
*H2 command.)
(Link Negotiation) Perform link negotiation at 1,200 bps for the
current connection only. (This dial modifier is equivalent to the
*H1 command.)
K
P
(Cell-Side Cellular Connection) Sets )M1 for the current
connection only.
(Pulse Dial) Placed anywhere in the dial string, causes the modem
to pulse dial. For example: ATD P5551234 <Enter>.
CSMIM-T1 Hardware Installation Guide
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
R
(Dial a Number in Answer Mode) Must follow the last character
in the dial string. Causes the modem to dial in answer mode when
calling an originate-only modem. For example:
ATD 5551234R <Enter>.
T
(Tone Dial) Placed anywhere in the dial string, causes the modem
to tone dial. For example: ATD T12345 <Enter>.
Tone dial is the default setting. The last P or T dial modifier
used remains in effect until you either enter a dial command
with a different P or T modifier or reset the modem. You can
combine P and T dial modifiers within a dial string. For
example, pulse dial a local telephone number and tone dial an
access code and phone number; type: ATD P5551234 T33
56789 <Enter>
NOTE
W
(Wait for Dial Tone Before Dialing) Inserted between digits in
a dial string, causes the modem to wait for a second dial tone up
to the register S7 time delay before dialing the number. If the
modem receives a dial tone before the register S7 delay expires, it
continues dialing. If it does not receive a dial tone, it displays NO
DIALTONE and hangs up. For example: ATD 5551234 W
5556789 <Enter>.
(Pause During Dial) Inserted in a dial string, causes the
modem to pause for the register S8 delay before dialing the
next digit. The default is 2 seconds. Use more than one comma
for a longer pause. For example, when you need to dial “9” and
pause for another dial tone before dialing an outside line:
ATD 9,,5551234 <Enter>.
NOTE
@
(Wait for Quiet Answer Before Dialing) Inserted between
characters in a dial string, causes the modem to wait for the
register S7 time delay, for at least one ring followed by five
seconds of silence, before acting on the next character in the dial
string. If the modem does not detect this sequence, it displays NO
ANSWER and hangs up. Use this modifier when the system you
are calling does not provide a dial tone. For example: ATD
5551234 @ 43210 <Enter>.
7-8
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
!
(Flash) Inserted between characters in a dial string, causes the
modem to go on hook for 1/2-second and then go back off hook,
as though you depressed the switch-hook button on your
telephone.
;
(Return to Command State After Dialing) Added to the end of
a dial string, tells the modem to remain in command state after it
dials the digits preceding the semicolon. This allows you to enter
dial strings longer than 98 characters. After the final Dial
command, the modem tries to establish a connection. To abort
dialing before you attempt to make a connection, type:
ATH<Enter>. Each Dial command except the last one must end
with a semicolon. For example:
ATD 9,5551234; <Enter>.
OK
ATD 5556789 @ 55512345678 W 344 <Enter>.
$
(Bong Detect) Detects an AT&T BELLCORE service prompt to
enter a calling card number and authorization. When the modem
encounters a “$” modifier within a dial string, it waits to receive
this “bong” signal. Once it detects it, the modem continues
processing the dial string. If the time set by register S7 elapses
first, the modem hangs up and displays NO PROMPT TONE.
7.2.1
Operating Mode Dial Modifiers
Use the following dial modifiers to override the \Nn command
setting. Placed anywhere in the dial string, these modifiers cause
the modem to override the \Nn setting for that connection only.
For example, if your modem is set for \N3 (auto-reliable) for
answering and you are calling a modem that you know does not
support error correction, use the Z dial modifier to force normal
mode: ATD 5551234Z <Enter>.
M
Q
(Dial in LAPM Mode) Placed anywhere in the dial string, causes
the modem to override current operating mode and dial in LAPM
reliable mode for the current connection only.
(Dial in LAPM Mode with Fallback to Normal) Placed
anywhere in the dial string, causes the modem to override current
operating mode and dial in LAPM reliable mode with fallback to
normal mode for the current connection only.
CSMIM-T1 Hardware Installation Guide
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
U
V
(Dial in Direct Mode) Placed anywhere in the dial string, causes
the modem to override current operating mode and dial in direct
mode for the current connection only.
(Dial in LAPM Mode with Fallback to MNP) Placed anywhere
in the dial string, causes the modem to override current operating
mode and dial in LAPM reliable mode with fallback to MNP for
the current connection only.
X
Y
Z
(Dial in Auto-Reliable Mode) Placed anywhere in the dial string,
causes the modem to override current operating mode and dial in
auto-reliable mode for the current connection only.
(Dial in MNP Reliable Mode) Placed anywhere in the dial string,
causes the modem to override current operating mode and dial in
MNP reliable mode for the current connection only.
(Dial in Normal Mode)
Placed anywhere in the dial string, causes the modem to override
the current operating mode and dial in normal mode for the
current connection only.
DL
Redial the Last Telephone Number Dialed
Redials the last telephone number that the modem dialed.
%Dn Disconnect Buffer Delay
Where n is an integer from 0 to 255 representing seconds (Default
is 0).
Sets a delay during which the modem attempts to process data in
its transmit or receive buffer before disconnecting. When your
software lowers DTR or you type ATH <Enter> the modem
attempts for n seconds to empty its transmit buffer before
disconnecting. When carrier drops, it attempts for n seconds to
empty its receive buffer before disconnecting. If its buffers are
empty or if n=0, it disconnects without delay.
If a physical disconnect occurs (for example, the connection drops
from too many retransmissions in reliable mode), the modem can
process only the receive buffer. If the delay expires before the
modem empties its buffers or it is in command state at disconnect,
it may lose data.
7-10
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
&Dn DTR Control
&D0 Ignores DTR. DTR not needed for auto-answer.
&D1 Enters command state on detecting On-to-Off transition of DTR;
DTR not needed for auto-answer.
&D2 Goes on hook on detecting On-to-Off transition of DTR and
prepares the serial port to accept an AT at any speed. DTR needed
for auto-answer.
&D3 Goes on hook and resets on detecting On-to-Off transition of DTR
and prepares the serial port to accept an AT at any speed. DTR
needed for auto-answer.
The On-to-Off transition of DTR must last as long as the value
specified in register S25 (default is 0.05 second). Positive
transitions of DTR (Off-to-On) that occur within five seconds
after disconnect are ignored.
-D
Repeat Dial
-D
<dial string> Where <dial string> is a string of up to 98
characters. Valid dial string characters are: 0-9, dial modifiers,
and for tone dial, #, A, B, C, D and *. The modem ignores invalid
characters.
-DL
Redials the last number dialed.
Redials a number up to 9 tries until connection. In reliable mode,
it does not redial if a remote modem answers but fails to establish
a reliable connection.
\Dn
Serial-Port DSR/CTS Control
\D0
DSR and CTS always On.
\D1
DSR and CTS follow DCD. If &C1 is also set, DSR follows off
hook.
\D2
\D3
\D4
DSR and CTS both follow DCD.
DSR complies with ITU-T recommendations, CTS always On.
DSR and CTS comply with ITU-T recommendations.
Controls the Data Set Ready (DSR) and Clear To Send (CTS)
signals on the serial port.
Table 7-1 shows the &C and \D settings and the result of
combining the two commands:
CSMIM-T1 Hardware Installation Guide
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
Hardware flow control overrides &C and \D settings for CTS.
(See \Q.)
NOTES
The modem ignores &C and \ D settings while connected in
V.23 half-duplex direct mode (%F3).When \D4 is set, &D
should be set to a value greater than 0.
ITU-T recommends that DSR come On when establishing a
connection and drop when the connection ends. It is also
recommended that CTS follow DTR while in command state;
drop either when answer tone is detected when originating,
when going off hook when answering, or when connection
ends; and follow connection status during connection.
Table 7-1 The &C and \D Settings
&C \D
Result
0
0
0
0
0
1
2
3
DCD On, DSR On, CTS On
DCD On, DSR On, CTS On
DCD On, DSR On, CTS On
DCD On, DSR complies with the ITU-T recommendations, CTS
On
0
1
1
4
0
1
DCD On, CTS/DSR comply with the ITU-T recommendations
DCD follows modem carrier, DSR On, CTS On
DCD follows modem carrier, DSR follows off hook, CTS follows
DCD
1
1
1
2
3
4
DCD follows modem carrier, DSR and CTS both follow DCD set-
ting
DCD follows modem carrier, DSR complies with the ITU-T recom-
mendations, CTS On
DCD follows modem carrier, CTS/DSR comply with the ITU-T
recommendations
7-12
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
2
0
DCD On (Off for a few seconds at disconnect only), DSR On,
CTS On
2
2
2
1
2
3
DCD, DSR, and CTS On (Off for a few seconds at disconnect)
DCD, DSR, and CTS On (Off for a few seconds at disconnect)
DCD Off at disconnect then On, DSR complies with the ITU-T
recommendations, CTS On
2
4
DCD On (Off for a few seconds at disconnect), CTS/DSR comply
with the ITU-T recommendations
En
Command Echo
E0
Inhibits the echoing of commands to the local device.
Echoes commands to the local device.
E1
%En Auto-Retrain
%E0 Disables the automatic retrain sequence.
%E1 Enables the automatic retrain sequence (at 2400 bps or higher).
When %E1 is set and line quality is too poor to sustain
communications, the modem tries up to three times to
resynchronize the modems (for a total of up to six seconds) before
hanging up. The modem can retrain during connections at 2,400
bps or higher. Use ATO1 to force the retrain sequence when %E0
is set.
The modem ignores %E0 during V.34, V.FC, V.32bis, and V.32
connections.
NOTE
-En
Modem-Port Data Length
-E0
Enables 10-bit data during normal mode connections.
Enables 11-bit data during normal mode connections.
-E1
Determines the number of data bits used on the modem port
during normal mode connections (when \N0 is set) when the serial
port is configured for asynchronous transmission of 11-bit
characters. Both modems must be set to the same number of data
bits.
CSMIM-T1 Hardware Installation Guide
7-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
The modems will not be able to pass data when a reliable
connection (\N3 or \N5 is set) falls back to a normal connection
NOTE
with 11-bit data characters enabled on both modems.
:En
Compromise Equalizer
:E0
Disables the compromise equalizer only when the modem is in
V.32bis or V.32 mode; may be useful for direct line connections
or PBX-to-PBX connections.
:E1
Enables the compromise equalizer; may be useful for
outside-line-to-outside-line or PBX-to-outside-line connections.
Controls equalization operation in V.32bis or V.32.
\En
Data Echo
\E0
Does not echo data sent by the local computer.
Echoes data sent by the local computer.
\E1
When operating in connect state, determines whether the modem
echoes characters sent from the local computer. \E1 functions
only during normal mode connections.
%Fn V.23 Mode
%F0 Allows multi-protocol answering; disables V.23 mode on
originate modem.
%F3
1,200 bps transmit, 1,200 bps receive (half-duplex) V.23 mode.
Detemines the V.23 mode used at 1,200 bps.
Entering AT%Fn (n=1, 2, or 3) disables all protocols except
V.23. Entering AT%Bn forces the %F0 setting.
NOTE
When %F0 is set and the modem is at 1,200 bps or higher, it can
answer as a V.23 1,200/1,200 bps half-duplex modem.
When %F3 is set, the modem can only establish normal or direct
1,200 bps half-duplex connections.
The \S command shows MODEM BPS V.23 AT when the
modem establishes V.23 connections.
7-14
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
Set %G1 first before setting %Fn.
NOTE
&F
Restore Factory Defaults
Restores factory default settings.
-Fn
Secondary Flow Control
-F0
Disables secondary flow control characters.
Enables secondary flow control characters.
-F1
Controls whether the modem sends or receives secondary flow
control characters on the serial port. When -F1 is set and primary
flow control enabled on the serial port, the modem sends two flow
control characters (one primary and one secondary) to the host for
flow control processing.
If the modem receives either a primary or secondary XOFF flow
control character, it stops sending data until it receives the
corresponding primary or secondary XON character.
%Gn Independent Serial-Port/Modem-Port Speed
%G0 Serial-port speed determines modem-port speed.
%G1 %B command determines modem-port speed.
Determines whether the modem-port speed updates to match the
serial-port speed with each AT command. When %G1 is set, the
modem-port speed does not update, and you must change it with
a %B or %Fn command.
&Gn Guard Tone
&G0 Disables guard tone.
&G1 Sets guard tone on the answering modem to 550 Hz.
&G2 Sets guard tone on the answering modem to 1800 Hz.
CSMIM-T1 Hardware Installation Guide
7-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
\Gn
Modem-Port Flow Control
\G0
\G1
\G2
Disables modem-port flow control.
Sets modem-port flow control to XON/XOFF.
Sets modem-port flow control to unidirectional XON/XOFF.
Sets the flow control method used to pace data between modems
during a normal mode connection. When \G1 is set, the modem
sends an XOFF character to stop receiving data, and sends an
XON character to resume. When \G2 is set, the modem sends
XON and XOFF characters to the remote device but ignores XON
and XOFF characters from the remote device.
Reliable mode has its own method of flow control and ignores
the \G setting, but \Qn settings remain active.
NOTES
Both modems must have the same primary flow control
characters set during normal connections. (See the :T9 and
:T10 register descriptions.)
H
Hang Up
H0
Disconnects from the remote system and hangs up the telephone
line.
H1
Disconnects from the remote system and goes off hook in
command mode.
The modem ignores ring signals and positive transitions of DTR
for 5 seconds after disconnect.
If %D is set to a value other than 0, hang up may not occur
immediately.
NOTE
7-16
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
*Hn
Link Negotiation Speed
*H0
*H1
*H2
Link negotiation occurs at the highest supported speed.
Link negotiation occurs at 1,200 bps.
Link negotiation occurs at 4,800 bps.
Sets the connection speed for link negotiation for connections
before upshift occurs between two MNP 10 modems. Use *H1 or
*H2 to set speed to 1,200 or 4,800 bps, respectively, to facilitate
link negotiation over poor phone lines.
In
I0
I1
I2
Identification
Displays the 4-digit modem product code.
Performs a checksum on firmware and displays 3-digit result.
Performs a checksum on the firmware ROM and displays the
checksum status, which should display OK.
I3
Displays modem name and firmware version.
-Jn
-J0
Detect Phase
Disables the detect phase.
Enables the detect phase.
-J1
Indicates whether the originating modem sends the V.42 control
sequence to the answering modem to determine the type of error
correction it has enabled. The answering modem can have LAPM,
MNP, or no error correction enabled. See the \N command
description for the types of connections.
\Jn
\J0
\J1
Bps Rate Adjust
Disables the bps rate adjust feature.
Enables the bps rate adjust feature.
After establishing a connection with \J1 set, the modem
automatically adjusts its serial port to match the connection speed
until disconnection. When \J0 is set, the serial-port rate is
independent of the rate of the connection.
CSMIM-T1 Hardware Installation Guide
7-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
When the modem establishes a reliable connection at speeds
between 4,800 and 16,800 bps with bps rate adjust enabled, the
serial-port speed adjusts to 9,600 bps. If the connection speed is
above 16,800 bps, the serial port adjusts to 19,200 bps. If you set
the serial port to the modem's highest rate of 115,200 bps, turn off
bps rate adjust to make sure that the serial port stays at 115,200
bps.
Refer to the %F command description for information about
using the \J command during V.23 connections.
NOTES
See the %Un command for information about resetting the
serial-port bps rate. When \J1\C0\N3 are set, the modem uses
direct mode instead of normal mode if a reliable connection is
not established.
We recommend turning off bps rate adjust (\J0) when using
data compression to retain the highest throughput.
-Kn
MNP Extended Services
-K0
-K1
-K2
Disables MNP Extended Services.
Enables MNP Extended Services.
Enables MNP Extended Services without MNP indication during
the answer detect phase.
MNP Extended Services allow two modems that support them to
use MNP data services that are not available with LAPM. For
example, negotiating MNP Class 10 with V.42bis compression in
preference to LAPM.
\Kn
Break Control
Where n is a number between 0 and 5 indicating the type of Break
the modem transmits (Default is 5).
Determines the type of Break the modem transmits when a Break
enters the modem. The following tables list the different effects of
the n value when the modem receives or transmits the Break. The
modem can buffer up to four Breaks on both the modem port and
the serial port.
7-18
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
In reliable link connect state, the sender's Break control setting
determines how the receiver handles the Break.
NOTE
Table 7-2 illustrates the \Kn command
Table 7-2 The \Kn Command
Local DTE sends Local DTE sends Local modem
Break during reli- \Bn; local modem sends Break
Remote
modem sends
Break during
normal connec-
tion
able or normal
connection
in command
mode, during reli- connection
able or normal
during direct
connection
Enter command
Empty data buff- Send Break to Empty data buff-
state; no Break to ers; send Break to remote system; ers; send Break
\K0
remote system*
remote system
set modem to
to serial port
command state
Empty data buff- Same as \K0
ers; send Break to
remote system
Send Break to Same as \K0
remote system
\K1
\K2
\K3
Same as \K0*
Immediately send Same as \K0
Immediately
send Break to
serial port
Break to remote
system
Immediately send Same as \K2
Break to remote
system
Same as \K1
Same as \K0
Same as \K2
Same as \K0*
Send Break to
remote system in
sequence with
any transmit data
being buffered
Send Break to
serial port in
sequence with
receive data
\K4
\K5
being buffered
Send Break to
remote system in
sequence with
transmit data
Same as \K4
Same as \K1
Same as \K4
*Forces the modem to command state. To transmit a Break and enter connect
state, type: AT\BO <Enter>.
CSMIM-T1 Hardware Installation Guide
7-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
%Ln Speed Matching
%L0 Provides partial speed matching.
%L1 Enables speed matching.
%L2 Disables speed matching.
%L3 Enables V.8 Automode with fallback to ITU-T Automode.
%L4 Enables V.8 Automode only.
Determines whether the modem uses speed matching to establish
a connection.
Both modems must support the V.8 protocol when using %L4
or a connection will not be made.
NOTE
Table 7-3 and Table 7-4 indicate the connections that the modem can
establish when %L1 or %L3 is set.
Table 7-3 Modem Connections When %L1 or %L3 is Set
Mode Setting on Answer Modem
Mode Set-
ting on
Originating
Modem
V.22[b] V.22[a] V.22bis V.32
V.32bis V.FC
V.34
V.34
(2400-28.8)
—
V.22[a]
V.22[a]
V.22[a]
V.22[a]
V.22[a]
V.22[a]
—
V.22bis V.32
V.22bis V.32
V.22bis V.32
V.22bis V.32
V.32bis V.FC
V.32bis V.FC
V.34
V.FC
(14.4-28.8)
—
V.FC
V.32bis
(4800-14.4)
—
V.32bis V.32bis V.32bis
V.32 V.32 V.32
V.32
(4800-9600)
—
V.22bis
(2400)
—
V.22bis V.22bis V.22bis V.22bis V.22bis
V.22[a]
(1200)
—
V.22[a]
—
V.22[a]
—
V.22[a]
—
V.22[a]
—
V.22[a]
—
V.22[b]
(600)
V.22[b]
—
Bell212A
(1200)
V.22[a]
V.22[a]
V.22[a]
V.22[a]
V.22[a]
V.22[a]
Bell103
(300)
—
Bell103 Bell103 Bell103 Bell103 Bell103 Bell103
7-20
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
When both the originate and answer modems are V.8 modems,
setting 300 bps will make a V.21 connection.
NOTE
Table 7-4 Modem Connections When %L1 or %L3 is Set
Mode Setting on Answer Modem
Mode Setting on
Originating Modem
Bell212A
Bell103
V.34 (2400-28,800)
V.FC (14,400-28,800)
V.32bis (4800-14,400)
V.32 (4800-9600)
V.22bis (2400)
V.22[a]
V.22
—
—
—
—
—
—
—
V.22[a]
V.22[a]
V.22[a]
V.22[a]
—
V.22[a] (1200)
V.22[b] (600)
Bell212A (1200)
Bell103 (300)
Bell212A
Bell103
Bell212A
Bell103
The following chart indicates the connections that the modem can
establish when %L4 is set. Both modems must support the V.8 protocol
when using %L4 or a connection will not be made.
CSMIM-T1 Hardware Installation Guide
7-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
Table 7-5 Modem Connections When %L4 is Set
Mode
Mode Setting: Answer Modem
Setting:
Originating
Modem
V.22[b] V.22[a] V.22bis V.32
V.32bis V.FC
V.34
V.34
(2400-28.8)
—
V.22[a]
V.22bis V.32
V.32bis V.FC
V.32bis V.FC
V.34
V.FC
—
V.22[a]
V.22bis V.32
V.FC
(14.4-28.8)
V.32bis
(4800-14.4)
—
V.22[a]
V.22[a]
V.22[a]
V.22[a]
—
V.22bis V.32
V.22bis V.32
V.32bis V.32bis V.32bis
V.32
(4800-9600)
—
V.32
V.32
V.32
V.22bis
(2400)
—
V.22bis V.22bis V.22bis V.22bis V.22bis
V.22[a]
(1200)
—
V.22[a]
—
V.22[a]
—
V.22[a] V.22[a] V.22[a]
V.22[b]
(600)
V.22[b]
—
—
—
To restrict the possible connections that can result, %L0 or %L2 can be
set on originating or answering modem. If %L2 is set, modem and
connection speeds are identical. Table 7-6 shows the modem connections
when %L0 is set.
7-22
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
Table 7-6 Modem Connections when %L0 is Set
Possible Connection Speed (bps)
Modem
Speed (bps)
300
300
600
600
1200
1200
2400
1200, 2400
4800
2400, 4800
7200
2400, 4800, 7200
9600
2400, 4800, 7200, 9600
2400, 4800, 7200, 9600, 12,000
2400, 4800, 7200, 9600, 12,000, 14,400
14,400
12,000
14,400
14,400V
16,800
19,200
21,600
2400, 4800, 7200, 9600, 12,000, 14,400, 16,800
2400, 4800, 7200, 9600, 12,000, 14,400, 16,800, 19,200
2400, 4800, 7200, 9600, 12,000, 14,400, 16,800, 19,200,
21,600
24,000
26,400
28,800
2400, 4800, 7200, 9600, 12,000, 14,400, 16,800, 19,200,
21,600, 24000
2400, 4800, 7200, 9600, 12,000, 14,400, 16,800, 19,200,
21,600, 24,000, 26,400
2400, 4800, 7200, 9600, 12,000, 14,400, 16,800, 19,200,
21,600, 24,000, 26,400, 28,800
%Mn Modulation Selection
%M0 Allows connections through V.32bis.
%M1 Allows connections through V.FC.
%M2 Allows connections through V.34 (default).
Controls the modem’s top modulation speed.
CSMIM-T1 Hardware Installation Guide
7-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
)Mn
Power Level Adjustment
for Cellular Telephone Connections
)M0
For central site modems: Auto-adjustment (adjusts power level if
remote modem is set to )M1). Use for MNP 10 modems that will
connect to both cellular telephone and non-cellular telephone site
modems.
)M1
For cell-side cellular modems: Forces power-level adjustment.
Adjusts the power levels during link negotiation for reliable
connections to accommodate signalling requirements of cellular
telephone equipment.
-Mn
MNP Class Connect Messages
-M0
Disables MNP Class connect messages.
Enables MNP Class connect messages.
-M1
Determines whether MNP Class connect messages are displayed.
The -M1 setting overrides the \V command setting for long form
connection result codes and the W command for serial-port
connect messages.
When -M1 is set and an MNP connection established, the connect
message is CONNECT MNPn/x, where n equals the MNP Class
(from 1 to 10) and x equals the type of data compression used
(V.42bis or MNP Class 5). If )M1 is set, the message is
CONNECT MNPn/y/x, where y equals CELLULAR. If the
modems do not negotiate compression, the message is
CONNECT MNPn.
During LAPM V.42bis connections when -M1 is set, the connect
message is CONNECT LAPM/V42BIS. During LAPM
connections with no compression active, the message is
CONNECT LAPM.
When -M1 is set, the message during normal and direct
connections is CONNECT.
The modem ignores this command with short-form result codes
enabled by V0.
Setting X0 will also override the -M setting by displaying only
CONNECT.
See also “Result Codes” in Chapter 6 for a complete list of
connect messages and result codes.
7-24
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
\Nn
Operating Mode
\N0
\N1
\N2
\N3
\N4
\N5
\N6
Sets normal mode.
Sets direct mode.
Sets reliable mode.
Sets auto-reliable mode.
Sets LAPM reliable mode.
Sets LAPM reliable mode with fallback to normal mode.
Sets LAPM reliable mode with fallback to MNP reliable mode.
You can use dial modifiers to set the operating mode for a
single call. See the D command description for details.
NOTE
Normal mode (\N0) can communicate with nearly any modem.
Error correction does not take place in normal mode.
Direct mode (\N1) does not buffer data and ignores flow control.
Also, in connect state, the serial port always adjusts to the speed
of the connection, regardless of the setting of \Jn. Error
correction does not occur.
\J0 disables the escape code sequence in direct mode.
NOTE
Reliable mode (\N2) uses the MNP reliable link to provide error
detection and automatic retransmission of data if an error occurs.
This provides for error-free communications between your
system and another that supports the MNP reliable link. When
\N2 is in effect, the modem disconnects if it fails to establish an
MNP reliable link immediately after making a connection.
During an MNP reliable link, both modems should use flow
control on the serial port. When one detects a transmission error,
it holds data in a buffer while they retransmit.
CSMIM-T1 Hardware Installation Guide
7-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
You may not want to use certain other protocols, such as HP
Block Mode, with MNP. Such protocols have particular timing
NOTE
requirements that can interfere with MNP’s effectiveness.
Auto-reliable mode (\N3) allows the modem to communicate
with remote systems which support the MNP or LAPM reliable
link and with systems that do not support the reliable link. In
auto-reliable mode, the answering modem looks for incoming
MNP or LAPM protocol characters from the remote modem. If it
detects them within approximately three seconds, it tries to
establish a reliable link connection.
When the modem is set to auto-answer in auto-reliable mode, you
can shorten this 3-second period by using the %A command with
\C2.
If both modems are set to auto-reliable mode, a normal
connection or no connection could result due to noise on the
NOTE
telephone line.
LAPM reliable mode (\N4) uses the LAPM reliable link to
provide error detection and automatic retransmission of data if an
error occurs. This ensures that communications between your
system and the remote system are error-free. The remote system
must also be equipped to handle an LAPM reliable link. The
modem attempts to establish an LAPM reliable link immediately
after making a connection. If the attempt fails, the modem
disconnects.
LAPM reliable mode with fallback to normal mode (\N5)
attempts to establish an LAPM reliable connection. If the LAPM
connection attempt fails, the modem falls back to a normal
connection.
LAPM reliable mode with fallback to MNP reliable mode
(\N6) attempts to establish an LAPM reliable connection. If the
LAPM connection attempt fails, the modem then tries to establish
an MNP reliable connection.
7-26
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
Table 7-7 indicates the type of connections, depending on the
operating mode. NC indicates No Connection. Where more than
one operating mode is in a column, the first mode is for the
originating modem and the second mode is for the answering
modem.
MNP Extended Services: In the chart, you can use MNP
Extended Services for V.42 connections where LAPM appears
if both modems are set with -K1 or -K2.
NOTE
Table 7-7 Connection Types Depending on Operating Mode
Answering
Modem
Originating Modem
\N0
\N1
\N2
NC
\N3
\N4
NC
\N5
\N6
NC
\N0
\N1
normal direct
normal
normal
/normal
normal direct
/direct
NC
normal
/direct
NC
NC
normal
/direct
NC
\N2
\N3
NC
NC
MNP MNP
MNP LAPM
NC
MNP
normal direct
LAPM LAPM
LAPM
/normal
NC
\N4
\N5
NC
NC
NC
LAPM
LAPM
LAPM LAPM
LAPM LAPM
LAPM
LAPM
direct
direct
/normal
\N6
NC
NC
MNP LAPM
LAPM LAPM
LAPM
On
Enter Connect State
O0
O1
Enters connect state.
Begins an equalizer retrain sequence when operating at 2,400 bps
or higher and then returns to connect state.
Type: ATO1 <Enter> to reduce errors due to loss of equalization
when excessive bit error rates are present.
CSMIM-T1 Hardware Installation Guide
7-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
%On V.23 Equalizer Control
%O0 Disables equalizers in V.23 half-duplex mode.
%O1 Enables equalizers in V.23 half-duplex mode.
Determines if equalizers are set in V.23 half-duplex mode. To
avoid transmission errors during V.23 half-duplex connections,
equalizer settings must be the same on both modems.
-On
Serial-Port Parity
-O0
-O1
-O2
-O3
-O4
-O5
-O6
-O7
7 data bits, odd parity.
7 data bits, even parity.
7 data bits, mark parity.
7 data bits, space parity.
8 data bits, no parity.
8 data bits, odd parity.
8 data bits, even parity.
8 data bits, mark parity.
Allows you to change the serial-port parity setting that is
automatically set by the AT sequence.
You can also use the -O command to change the serial-port parity
while connected to a remote device. Use this command when the
local device supports XON/XOFF flow control and detects parity.
This command ensures that all XON and XOFF characters
generated by the modem have the correct parity.
You cannot change modem-port parity during a connection.
When parity is required for a connection and is different than the
parity set by the AT sequence, the parity must be set at the same
time the dial command is issued and entered on the same
command line.
For example:
AT-O4D12345 <Enter>
7-28
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
8 -bits and mark parity. The AT sequence cannot be used to
match 8-bit data with mark parity. Eight data bits plus mark
parity can only be set by the AT-O command. If -O7 is not set,
the modem defaults to 8 data bits, no parity.
NOTES
Space parity. The AT sequence cannot be used to match
space parity; no parity is set instead.You must enter AT-O3 to
set space parity.
P
Pulse Dial
Changes the current dialing mode to pulse. Tone is the default.
-Pn
Check Parity
-P0
Ignores parity of special characters.
-P1
Processes special characters only if their parity matches that of the
serial port.
-P2
Processes special characters only if their parity matches that of the
serial port. Recognizes modem-port flow-control characters,
however, regardless of their parity.
Controls checking of parity for XON and XOFF characters, the
escape code sequence, and HP ACK characters. In command
state, the modem sends all command echoes and command
responses to the PC with parity that matches the serial port’s.
With -P0 or -P1 set, all received data pass through to the computer
at 8 data bits, no parity.
With -P2 set, all received data pass through to the computer with
parity corrected to match the serial-port parity.
The -P command is used only for 10-bit data; the modem
ignores -Pn when it is set for 11-bit data.
NOTE
CSMIM-T1 Hardware Installation Guide
7-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
Qn
Quiet
Q0
Q1
Q2
Enables output of result codes.
Disables output of result codes.
Disables answer mode result codes only.
Determines whether the modem sends result codes and status
codes (OK, BUSY, RING, etc.) to your computer.
-Qn
Fallback Modulation Speeds
-Q0
Disables fallback from a V.32bis or V.32 MNP reliable
connection to an MNP reliable 2400 or 1,200 bps connection.
-Q1
Enables fallback from a V.32bis or V.32 MNP reliable connection
to an MNP reliable 2,400 bps connection.
-Q2
Enables fallback from a V.32bis or V.32 MNP reliable connection
to an MNP reliable 2,400 or 1,200 bps connection.
Controls whether the modem can fall back from a V.32bis or V.32
MNP reliable connection to a V.22bis MNP reliable connection at
2,400 bps or a V.22 MNP reliable connection at 1,200 bps.
Fallback may occur when poor telephone lines cause excessive
MNP retransmissions.
Fallback from a V.32bis or V.32 MNP reliable connection to a
4,800 bps V.32bis or V.32 MNP reliable connection is always
enabled, regardless of the -Q setting. The modem always uses the
V.22 standard when it falls back from a V.32bis or V.32 MNP
reliable connection to a 1,200 bps MNP reliable connection,
regardless of the B setting.
\Qn
Serial-Port Flow Control
\Q0
\Q1
\Q2
Disables flow control.
Enables bi-directional XON/XOFF flow control.
Enables unidirectional hardware flow control; the modem uses
CTS to control the terminal.
\Q3
\Q4
\Q5
Enables bi-directional hardware flow control.
Enables unidirectional XON/XOFF flow control.
Keeps CTS Off until connection for unidirectional hardware flow
control.
7-30
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
\Q6
Keeps CTS Off until connection for bi-directional hardware flow
control; ignores RTS until connection.
Sets the type of flow control used on the serial port. If the
serial-port speed is faster than the modem-port speed, data from
your computer enter the modem faster than they leave.
The modem holds characters in a buffer and sends them out at the
slower modem-port bps rate. When the buffer is full, flow control
instructs your computer to stop transmitting data to the modem;
the modem continues to send out the characters and empty the
buffer. When there is room in the buffer, flow control instructs
your computer to resume transmitting data to the modem.
For reliable connections, retransmissions can reduce the effective
modem-port speed. If this occurs, flow control prevents buffer
overflow.
During direct mode connections, the modem does not use flow
control and ignores the \Q setting.
Hardware flow control overrides the &C and \D settings for CTS
operation.
NOTE
\Q1 enables bi-directional XON/XOFF flow control. Sending an
XOFF character stops data transmission; sending an XON
character restarts it. The modem generates XON and XOFF
characters at the same parity as on the serial port. The serial port
responds to XON and XOFF characters from the local computer
in the same way.
\Q2 enables unidirectional hardware flow control. The modem
turns CTS Off to signal the local computer to stop transmitting
data, and turns CTS On to signal the local computer to resume
transmitting data.
\Q3 sets bi-directional hardware flow control using the CTS and
RTS signals. The modem uses the CTS signal to start and stop
data transmission from the local computer. When RTS is Off, the
modem stops transmitting data to the local computer. When RTS
is On the modem resumes sending data.
CSMIM-T1 Hardware Installation Guide
7-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
\Q4 enables unidirectional XON/XOFF flow control. The modem
serial port generates, but does not respond to, XON/XOFF flow
control characters. This setting allows for computers to transmit
data that has XON and XOFF data characters. The computer can
still be set to respond to XON/XOFF flow control characters sent
to it from the modem during serial-port flow control.
\Q5 enables unidirectional hardware flow control the same as
\Q2, but also keeps CTS Off until a connection is established.
\Q6 enables bi-directional hardware flow control the same as \Q3,
but also keeps CTS Off until a connection is established and
ignores RTS while not connected.
%Rn Read All Registers
%R0 Displays the contents of all S registers in decimal and
hexadecimal integers in tabular format.
%R1 Displays the contents of all :T registers in decimal and
hexadecimal integers in tabular format.
&Rn RTS/CTS Options
&R2 ITU-T V.13 emulates half-duplex over a full duplex line.
Use &R2 to simulate half-duplex operation.
The modem ignores &R during asynchronous connections.
NOTE
Sn?
Read Configuration Registers
Where n is an integer from 0 to 27, indicating a register, displays
the contents in decimal form of the selected register.
&Sn DSR Options
&S0
DSR always on.
&S1
DSR complies with ITU-T recommendations.
Controls the Data Set Ready (DSR) signal on the serial port.
7-32
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
&S0 is equivalent to setting \D0. &S1 is equivalent to setting
NOTE
\D3.
\S
Read Online Status
Displays a list of modem commands and their current settings.
This command also displays the active connection type, as well as
the elapsed connect time and the telephone number most recently
dialed.
The \S command displays several screens. Press any key to move
to the next screen. To cancel the display, type the line-delete
character – or send a Break.
T
Tone Dial
Changes the current dialing mode to tone. Tone is the default.
&Tn Test and Diagnostics Commands
&T0
&T1
&T3
&T4
End test in progress.
Local analog loopback.
Local digital loopback.
Respond to remote digital loopback.
&T5 Do not respond to remote digital loopback.
&T6
&T7
&T8
Remote digital loopback.
Remote digital loopback with self-test.
Local analog loopback with self-test.
The modem does not support &Tn commands for Bell 103,
V.13, V.21, and V.23 modes.
NOTE
&T0 ends a test in progress without terminating a connection, and
returns the local and remote modems to normal operation. If
self-test is in progress, &T0 reports any errors. &T0 must be the
last command on a command line.
CSMIM-T1 Hardware Installation Guide
7-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
&T1 makes the modem display the characters on your screen
exactly as you type them. The modem must be in normal or direct
mode and set to 1200 bps or higher.
&T3 allows a remote modem that does not support the ITU-T
V.54 standard to perform a Remote Digital Loopback test with
your modem. The modem must connect in normal or direct mode
and be set to 1200 bps or higher.
&T4 allows the modem to respond to a remote caller’s request to
enter Remote Digital Loopback mode.
&T5 prevents the modem from responding to a Remote Digital
Loopback request.
&T6 instructs the remote modem to initiate a Remote Digital
Loopback. It is available only when the modem is connected in
normal or direct mode and set to 1200 bps or higher.
&T7 instructs the remote modem to enter a Remote Digital
Loopback with Self-Test. Upon completion of the test, the modem
reports errors to the local device. This command is available only
when the modem connects in normal or direct mode and is set to
1200 bps or higher.
&T8 makes the modem send itself the ITU-T V.54 test pattern
and verify these characters. Upon completion of the test, the
modem reports errors to the local device. This command is
available only when the modem is in normal or direct mode and
set to 1200 bps or higher.
\Tn
Inactivity Timer
Where n is an integer from 0 and 90 in minutes (Default is 0).
Specifies the number of minutes the modem waits for data before
automatically hanging up. \T0 (default) disables the inactivity
timer. The inactivity timer is only available during normal and
reliable link connections; the modem ignores it in direct mode.
%Un Clear Serial-Port Speed
%U0 Allows the current serial-port speed change from any speed.
%U1 Always keeps the current serial-port speed. To change serial-port
speed, you must enter %U1 each time you change it.
%U2 Allows the current serial-port speed change from any speed.
7-34
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
You do not need to issue %U when bps rate adjust causes the
serial-port speed to change during a connection.
NOTE
You must enter AT%U0 when changing from 11-bit characters to
10-bit characters, and from 10-bit to 11-bit.
When the serial-port speed is set to 38,400 bps, you cannot change
it until you enter an AT%Un or reset it.
To save the configuration even after the modem is reset, also
issue either &W or *W.
NOTE
Vn
Result Code Form
V0
Sends short-form result codes.
Sends long-form result codes.
V1
Selects whether the modem sends long-form (verbose) or
short-form (numeric) result codes to your computer. The format
of the connection result codes is dependent upon the \V, W, and
-M commands.
%V
\Vn
Display Modem Firmware Version
Displays the modem firmware main code version.
Error Correction Result Code Form
\V0
\V1
Uses standard long-form result codes: CONNECT <speed>
Adds /REL to long-form error correction result codes:
CONNECT <speed>/REL
\V2
Displays long-form error correction protocol result codes:
CONNECT <speed>/REL-MNP or
CONNECT <speed>/REL-LAPM or
CONNECT <speed>/REL-CELLULAR
\V3
\V4
Adds /REL to long form error correction result codes:
CONNECT <speed>/REL. Displays Hayes-compatible
short-form (numeric) result codes.
Displays long-form error correction protocol result codes:
CSMIM-T1 Hardware Installation Guide
7-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
CONNECT <speed>/REL-MNP or
CONNECT <speed>/REL-LAPM or
CONNECT <speed>/REL-CELLULAR
\V5
Displays \V4 plus modulation V.34, V.FC, V.32, or V.22.
Determines whether result codes indicate that a reliable link
connection is in effect. The W setting determines the contents of
the <speed> field. Setting -M1 changes the format of the
long-form connect result codes.
Even for a reliable connection, use \V0 if the communications
software does not expect to see a reliable link result code.
Use \V1, \V2, \V3, \V4 or \V5 when your software supports error
correction result codes.
Use V0\V3 if your communications software requires
Hayes-compatible connection result codes. Note that when V1 is
set to select long-form result codes \V3 is equivalent to \V1.
Use \V3, \V4 or \V5 to see actual connect speed.
When either \V1 or \V2 is set, the message CONNECT
9600/REL displays during 4800, 7200, and 12000 bps reliable
connections. When either \V3 or \V4 is set, the actual modem
bps rate displays for 4800, 7200, and 12000 bps reliable
connections.
NOTE
^V
Display Bootstrap Revision
Requests modem to display its current flash memory bootstrap
revision.
Wn
Connection Speed Reporting
W0
W1
W2
Displays serial-port connect messages.
Displays serial-port connect messages.
Displays modem-port connect messages.
When W0 or W1 is set, the speeds reported in connect messages
indicate the serial-port speed.
When W2 is set, the speeds reported in connect messages indicate
the modem-port speed.
7-36
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
When X0 is set, CONNECT displays, regardless of W setting.
See the section entitled “Result Codes,” for a list of valid connect
messages and result codes.
%Wn Pulse Digit Command
%W0 n pulse digits dialed for each number.
%W1 n+1 pulse digits dialed for each number.
%W2 10-n pulse digits dialed for each number.
For pulse dialing, determines whether the modem dials each
number in a dial string n pulses, n+1 pulses, or 10-n pulses. For
example, when %W0 is in effect, it dials 6 with 6 pulses.
However, with %W1, it dials 6 with 7 pulses; with %W2, it dials
6 with 4 pulses.
With %W0 or %W2 set, the modem dials digit 0 with 10 pulses.
When %W1 is set, digit 0 is dialed with 1 pulse.
NOTE
&Wn Store Current Configuration
Stores current user profile n, where n = 0 to 3 (Default is 0).
Stores the active commands and certain S-registers. You store
telephone numbers independently with the \Pn and &Zn
commands. AT&W stores the serial-port speed and parity and the
modem-port speed that are in effect when you enter &W.
AT&W does not store the following restricted S-registers:
S2
S3
S4
S5
S6
S7 S8 S9 S10 S11 S12
*Wn Store Complete Configuration
Stores complete user profile n, where n = 0 to 3 (Default is 0).
Stores all active commands and registers as well as the restricted
S-registers not stored with &W. (See the &W command
description.)
CSMIM-T1 Hardware Installation Guide
7-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
Save telephone numbers independently with the \Pn and &Zn=
commands. The *W command saves the serial-port speed and
parity and the modem-port speed in effect when you enter *W.
See also the &W, &Y, and Z commands. Refer to the section
entitled “Storing Multiple User Profiles” for details on multiple
user profiles.
The &W and *W commands share the same stored
configuration area. Issue one of these commands to override
NOTE
the other stored settings.
The &W command setting stores default settings for the restricted
S-registers. If &W is issued after issuing *W, the default settings
for the restricted S-registers are stored. If you change the setting
of one of the restricted S-registers and want to save it, use the *W
command instead of the &W command.
Xn
Extended Result Codes
X0
Modem ignores dial tone and busy signals. Displays CONNECT
when it establishes a connection. Smartmodem 300 compatible.
X1
X2
Modem ignores dial tone and busy signals. Sends a connect result
code including bps rate when it establishes a connection.
Modem ignores busy signals. Displays NO DIALTONE if it does
not detect one within 5 seconds of dialing. Sends a connect result
code reflecting bps rate when it establishes a connection.
X3
Modem ignores dial tone. Displays BUSY if it detects a busy
signal. Sends a connect result code reflecting bps rate when it
establishes a connection.
X4
Displays NO DIALTONE if it does not detect one within 5
seconds of dialing. Displays BUSY if it detects a busy signal.
Sends a connect result code reflecting bps rate when it establishes
a connection.
Determines whether the modem responds to dial tone and busy
signals, and what kind of CONNECT result codes are displayed.
Result codes are further controlled by the Vn command. Result
codes indicate MNP reliable mode only when either \V1, \V2,
\V3, \V4, \V5 or -M1 is set. When the modem ignores dial tone,
it waits for the register S6 time delay to expire and then dials
regardless of whether a dial tone is present.
7-38
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
The “W” dial modifier causes the modem to wait for dial tone
regardless of the X setting.
NOTE
\Xn
XON/XOFF Pass-Through
\X0
Processes XON/XOFF flow control characters.
\X1
Processes XON/XOFF flow control characters and passes them to
the local or remote system so that the local or remote device also
processes them.
Determines whether XON/XOFF flow control characters pass to
the remote or local modem. With XON/XOFF flow control
enabled on the serial port (\Q1) and pass through enabled (\X1),
the modem also transmits to the remote device any XON and
XOFF characters sent to the serial port from the local device.
With \ X0 set and XON/XOFF flow control enabled, local
devices such as computers or printers may send XON and
XOFF characters to the modem serial port. If the modem is
already controlling data flow to the remote system, local flow
control characters will not interfere with the connection.
However, if \ X1 is set, local flow control characters also pass to
the remote system. These characters intended for the local
system may turn on the flow of data from the remote system
before the modem is ready to receive more data, resulting in a
loss of data.
!
CAUTION
Yn
Long Space Disconnect
Y0
Disables long space disconnect on receipt of H, or DTR drop if
&D2 or &D3 is set.
Y1
Enables long space disconnect on receipt of H, or DTR drop if
&D2 or &D3 is set.
Sends a Break up to 4 seconds before disconnecting in response
to an H command, or if DTR drops and either &D2 or &D3 is set.
If &D3 is set and DTR drops, the modem disconnects. If the
answer modem sees the Break, it drops the connection.
CSMIM-T1 Hardware Installation Guide
7-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
Yn is available only during normal and direct connections.
NOTES
Y1 must be set on both modems to take effect.
&Yn Designate Default User Profile
Selects user profile n, where n = 0 to 3 (Default is 0).
Designates which of four user profiles the modem loads into
active configuration at power up, or when DTR drops when &D3
is set. It saves this command immediately after you enter it; you
do not have to enter &W or *W. Also, when you enter &F, this
command does not change.
You can use the &Y command to select a user profile. The
setting takes effect immediately. When you reset or power up
NOTE
the modem, it restores the last user profile setting selected.
Zn
Reset
Resets user profile n, where n = 0 to 3.
Hangs up the phone line and clears the modem and serial-port
buffers. Also, restores commands and registers that you last saved
with either &W or *, or the factory defaults if you have not
entered an &W or *W.
To reset the modem, type: ATZn <Enter> (n = 0 to 3). If OK does
not appear, type: ATQ <Enter> to enable result codes.
7-40
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
7.3
REGISTERS
Some registers control a single function. Others control several functions
and are bitmapped. We recommend bitmapped registers for reading
modem status only; we suggest you use commands to change the
modem’s settings.
7.3.1
Commands to Change or Read Registers
Change the Value of a Register
Sn=x
:Tn=x
Changes the value of S or :T register “n” to a new value “x”.
Change the Value of the Last Referenced S-Register
=x
Changes the value of the last referenced S-register or the
register pointed to with the ATSn command. For example, if the
last register command used was ATS0=2, entering AT=4
changes the value of register S0 from 2 to 4.
Display the Value of the Last Referenced S-Register
?
Displays the value of the last S-register referenced in a read,
write, or point to command.
Point to New Register
Sn
Where n is an integer from 0 to 27, indicating a register,
instructs the modem to point to the register whose location is n.
This becomes the last referenced register. For example, typing
ATS1 <Enter> places the pointer at register S1 and returns the
command prompt.
Read All Registers
%Rn
%R0
Displays the contents of all S registers in decimal and
hexadecimal integers in tabular format.
%R1
Displays the contents of all :Tn=n commands in decimal and
hexadecimal integers in tabular format.
Read Configuration Register
Sn?
Where n is an integer from 0 to 27, indicating an S register.
CSMIM-T1 Hardware Installation Guide
7-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
:Tn?
Where n is an integer from 0 to 29, indicating a :T register.
Displays the contents in decimal form only of register “n”.
Register Descriptions
S0=n
Ring to Auto-Answer On
Range: 0 - 255 rings
Default: 1 ring (auto-answer enabled)
Sets the number of rings required before the modem answers.
ATS0=0 disables auto-answer.
The modem ignores ring signals for 5 seconds after disconnect.
S1=n
Ring Counter
Range: 0 - 255 rings
Default: 0 rings
Keeps a running total of the number of rings that occur before
the modem answers a call. If no ring occurs within 8 seconds
after the last ring, the ring counter resets to 0.
The modem ignores ring signals for 5 seconds after disconnect.
S2=n
Escape Code Character
Range: 0 - 255, ASCII decimal
Default: 43 (+)
Sets the character used for the three-character escape code
sequence. When the modem is in connect state and receives the
escape code sequence, it enters command state. Setting register
S2 to 0 disables the escape code character. See register S12 to
set the guard time that brackets the escape code character.
The modem does not store this register with &W; enter *W to save it.
S3=n
Carriage Return Character
Range: 0 - 127, ASCII decimal
Default: 13 (carriage return)
Sets the character recognized as a carriage return. The carriage
return terminates command lines and result codes.
The modem does not store this register with &W; enter *W to save it.
7-42
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
S4=n
Line Feed Character
Range: 0 - 127, ASCII decimal
Default: 10 (line feed)
Sets the character recognized as a line feed. The line feed
character follows the carriage return at the end of command
lines and result codes.
The modem does not store this register with &W; enter *W to save it.
S5=n
Backspace Character
Range: 0 - 32, ASCII decimal
Default: 8 (backspace)
Sets the character recognized as a backspace.
The modem does not store this register with &W; enter *W to save it.
S6=n
Wait Before Dialing
Range: 2 - 255 seconds
Default: 2 seconds
Sets the length pause after off hook before the modem dials. The
modem always pauses for a minimum of two seconds, even if
S6 is set less than 2.
Register S6 is valid only when either X0, X1, or X3 is set.
NOTE
The modem does not store this register with &W; enter *W to
save it.
S7=n
Wait for Carrier After Dial
Range: 0 - 255 seconds
Default: 60 seconds
Sets the length of time that the modem waits for
• Carrier from remote modem before hanging up (originate or
answer mode).
• Ring back (originate mode only, and only if either X3 or X4 is
set).
• Dial tone when the “W” dial modifier is encountered in a dial
string.
CSMIM-T1 Hardware Installation Guide
7-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
• Quiet answer when the “@” dial modifier is encountered in a
dial string.
The modem does not store this register with &W; enter *W to save it.
S8=n
Pause Time for Dial Delay
Range: 0 - 255 seconds
Default: 2 seconds
Sets the length of time to pause when the modem encounters the
pause dial modifier (“,” - comma).
The modem does not store this register with &W; enter *W to save it.
S9=n
Carrier Detect Response Time
Range: 0 - 255 tenths of a second
Default: 6 (0.6 seconds)
Determines how long a signal must be present before the
modem recognizes it as a carrier.
The modem does not store this register with &W; enter *W to
save it.
NOTES
Register S9 is only used in normal and direct modes.
S10=n Delay for Hang Up After Carrier Loss
Range: 0 - 255 tenths of a second
Default: 60 (6 seconds)
Sets the length of time the modem waits before hanging up loss
of carrier, allowing for a temporary loss. Both modems should
have equal S10 values. Otherwise, disconnect occurs when the
lower value is reached. When register S10 is set to 255, the
modem functions as if carrier is always present.
After disconnecting, the modem waits for a minimum of five
seconds before going off hook again in originate mode.
The modem does not store this register with &W; enter *W to
save it.
NOTES
Register S10 is ignored during V.34, V.FC, V.32bis, V.32,
V.22bis, and V.22 reliable connections.
7-44
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
S11=n DTMF Tone Dialing Speed
Range: 50 - 100 milliseconds
Default: 75 milliseconds
Sets the length of time after the last tone and before the next
tone is sent when the modem is dialing over a touch tone line.
The modem does not store this register with &W; enter *W to save it.
S12=n Escape Code Guard Time
Range: 0 - 255 (fiftieths of a second)
Default: 50 (1 second)
Sets the minimum “quiet” time that must be present before and
after entering the escape code. The delay between each
character in the escape code must be less than this guard time.
If register S12 is set to 0, the time it takes to enter the escape
code does not affect recognition.
The modem does not store this register with &W; enter *W to
save it.
NOTES
Register S12 sets the guard time that precedes and follows the
attention character sequence. It should be set to the same
value on both the originating and answering modems.
S14=n Bit Mapped Register
The modem saves the following command settings when you
enter them. You do not need to enter &W or *W .
CSMIM-T1 Hardware Installation Guide
7-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
Table 7-8 Saved Command Settings with S14
Bit
Position
Function
Decimal Value
0
1
not used
command echo
0
1
0
1
0
1
0
1
0
1
no echo
echo
2
3
4
5
result codes
result type
result codes
no result codes
short form
long form
dumb mode
dial method
smart mode
dumb mode
tone dial
pulse dial
6
7
not used
originate/answer
0
1
answer mode
originate mode
S16=n Bit Mapped Register, Test Options
Commands enable and disable loopback test options. Register S16 is a
read-only register that displays loopback test option status, and is
available only when the modem is in normal or direct mode. The modem
supports all loopback tests at 1200 bps or higher, but does not support
diagnostics in Bell 103, V.13, V.21, or V.23.
7-46
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
Table 7-9 Saved Command Settings with S16
Bit
Position
Function
Decimal Value
0
Local Analog Loopback
0
1
disabled
enabled
1
2
not used
Local Digital Loopback
0
1
disabled
enabled
3
Remote Digital Loopback status
(initiated by the remote modem)
0
1
loopback Off
loopback in
progress
4
5
6
7
Initiate Remote Digital
Loopback
0
1
0
1
0
1
disabled
enabled
disabled
enabled
disabled
enabled
Initiate Remote Digital
Loopback with Self-Test
Initiate Local Analog
Loopback with Self-Test
not used
S18=n Test Timer
Range: 0 - 255 seconds
Default: 0 seconds (disables timer)
Sets how long the modem conducts a loopback diagnostic test.
Register S18 is available only in normal or direct mode. When
S18 is set to 0, type AT&T0 <Enter> to end a test.
CSMIM-T1 Hardware Installation Guide
7-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
S21=n Bit Mapped Register (Table 7-10)
Table 7-10 Saved Command Settings with S21
Bit
Function Decimal Value
Position
3,4
DTR
0
1
Ignores DTR (&D0)
On-to-Off DTR transition: modem enters com-
mand state (&D1)
2
3
On-to-Off DTR transition: modem goes on
hook (&D2)
On-to-Off DTR transition: modem resets
(&D3)
5
DCD
0
1
DCD always On
DCD On indicates data carrier is present or
DCD On except momentarily at disconnect
6
7
not used
long space
disconnect
0
1
off (Y0)
on (Y1)
S22=n Bit Mapped Register (Table 7-11)
Table 7-11 Saved Command Settings with S22
Bit
Position
Function
Decimal Value
4,5,6
result code
options
0
4
5
6
7
0
1
same as X0
same as X1
same as X2
same as X3
same as X4
39/61
7
make/break
ratio
33/67
7-48
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
S23=n Bit Mapped Register (Table 7-12)
Table 7-12 Saved Command Settings with S23
Bit
Position
Function
Decimal Value
0
respond to remote digi-
tal loopback
0
1
disabled
enabled
1,2,3
serial-port bps
0
1
2
3
4
5
6
7
0 to 300 bps
600 bps
1200 bps
2400 bps
4800 bps
9600 bps
19200 bps
38400, 57600 and
115200 bps
4,5
6,7
parity option
guard tones
0
1
2
3
0
1
2
3
even
space/none
odd
mark
disabled
550 Hz
1800 Hz
not used
The modem ignores the Respond to Remote Digital Loopback option
during reliable connections.
CSMIM-T1 Hardware Installation Guide
7-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
If you use register S23 to change the parity set automatically or
set by -On, the same number of data and stop bits used before
NOTE
the change is retained. For example, if 8 data bits and even
parity is set (-O6) and you change register S23 to odd parity,
the 8 data bits and 1 parity bit are retained. However, the parity
becomes odd instead of even, changing the Serial-Port Parity
command setting to -O5.
S25=n Delay to DTR and Asynchronous Time Delay
Range: Delay to DTR: 0 - 255 hundredths of a second
Async mode: 0 - 255 seconds
Default: Delay to DTR: 5 hundredths of a second (0.05 seconds)
Async mode: 5 seconds and 0.05 seconds
Delay to DTR: During asynchronous mode with &M2 or &M3
set, the modem ignores an On-to-Off transition of DTR that is
less than the register S25 time delay.
Asynchronous time delay: Register S25 sets the number of
seconds the modem waits to check DTR after establishing a
connection. After this time delay, the Delay to DTR time delay
described above takes effect when loss of DTR occurs.
S27=n Bit Mapped Register (Table 7-13)
Table 7-13 Saved Command Settings with S27
Bit
Position
Function
Decimal Value
6
answer tone when at 1200
bps
0 ITU-T V.22bis/V.22
1 Bell 212A when supported
7
not used
:T0=n
Timer for V.22bis, V.22, and V.32 Modes During
Multi-Protocol Answer
Where n is an integer from 0 to 255, in tenths of a second.
Default is 40 (4 seconds).
7-50
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
This command requires 1200 bps or higher operation with
%F0%L1 set.
Determines how long the modem attempts to establish a V.32,
V.22bis, or V.22 connection before attempting to establish a
V.21 connection. During this period, the modem sends V.22bis
or V.22 carrier.
:T2=n
Timer for V.21 Mode During Multi-Protocol Answer
Where n is an integer from 0 to 255 representing tenths of a
second. Default is 0 (V.23 half-duplex disabled).
This command requires 1200 bps or higher operation with
%F0%L1\N3 set.
When the modem is unable to establish a V.32, V.22bis, or a
V.22 connection, :T2 determines how long the modem attempts
to establish a V.21 connection before attempting a V.23
half-duplex connection. During this period, the modem sends
V.21 carrier.
Set :T2=20 (2 seconds) when including V.23 half duplex in the
multi-protocol answer modem.
If :T2 is set to 0, V.23 half-duplex connections are not
attempted. The modem attempts to establish a connection for
the length of time specified by register S7 before hanging up.
NOTE
:T3=n
Timer for V.21 and V.23 Answer Tone Duration
Where n is an integer from 0 to 33 (tenths of a second)
Default is 33 (3.3 seconds).
This command requires either V.21 operation (%F0 is set and
the modem speed is 300 bps) or V.23 operation (%Fn, where
n=1, 2, or 3).
When the answering modem is set for V.21 or V.23 operation,
:T3 determines the duration of the V.25 answer tone that is sent
to the originating modem. When :T3 is set to 0, no answer tone
is sent. All V.21 and V.23 answers begin with two seconds of
silence unless :T3 is set to 0.
CSMIM-T1 Hardware Installation Guide
7-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
When the originating modem is set for V.21 or V.23 operation,
:T3 determines how long the modem waits after detecting
answer tone before proceeding with the connection. When :T3
is set to 0, the originating modem does not wait for answer tone.
:T4=n
Timer for Line Turnaround Delay - Carrier On
Where n is an integer from 0 to 255 (in increments of 12.5
milliseconds). Default is 20 (250 milliseconds).
This command takes effect only during normal mode V.23
half-duplex connections.
After the modem turns carrier off, determines the minimum
time the modem waits for the remote modem to respond before
turning carrier back on again to resume sending data.
:T5=n
Timer for V.23 Half-Duplex Intercharacter Delay
Where n is an integer from 0 to 255 (in increments of 12.5
milliseconds). Default is 7 (87.5 milliseconds).
This command takes effect only during normal mode V.23
half-duplex connections.
Sets the length of time the modem waits after transmitting the
last data character in the transmit buffer before turning carrier
off. :T5 may need to be adjusted if the local computer
intercharacter time causes excessive line turnarounds.
:T6=n
Timer for DCD Turn On Delay
Where n is an integer from 0 to 255, representing milliseconds.
Default is 200 milliseconds (2 tenths of a second).
This command takes effect during only normal mode V.23
half-duplex connections.
Sets how long the modem waits after carrier goes on before it
starts looking for data. This command may be set to exclude the
turn on noise that occurs when DCD turns On during V.23
half-duplex connections.
If :T6 is set to 0, the modem waits 256 milliseconds before
looking for data.
7-52
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
:T7=n
Timer for False Answer Abort
Where n is an integer from 0 to 255, representing seconds.
Default n=60 seconds; setting :T7=0 disables this timer.
This command takes effect only when the modem falls back to
a normal mode V.23 half-duplex connection.
Sets the amount of time the modem waits before hanging up
when it receives no data. If this command is set to a value
greater than zero, the timer starts when the modem connects. If
the modem does not receive data in the specified time, it hangs
up.
:T9=n
Primary XON Flow Control Character
Where n is a decimal from 0 to 255, representing an 8-bit
character. Default n=11 hexadecimal (or 17 decimal) <DC1>.
Defines the character used for primary XON flow control on the
modem and serial ports. Enable primary flow control with \Q1,
\Q4, \G1, or \G2.
With modem-port flow control, both modems must have the
same primary flow control characters set during normal
connections.
NOTE
:T10=n Primary XOFF Flow Control Character
Where n is a decimal from 0 to 255, representing an 8-bit
character. Default is 13 hexadecimal (or 19 decimal) <DC3>.
Defines the character used for primary XOFF flow control on
the modem and serial ports. Enable primary flow control with
\Q1, \Q4, \G1, or \G2.
CSMIM-T1 Hardware Installation Guide
7-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
:T11=n Secondary XON Flow Control Character
Where n is a decimal from 0 to 255, representing an 8-bit
character. Default is F9 hexadecimal (or 249 decimal).
Defines the character used for secondary XON flow control on
the modem’s serial port. For secondary flow control to take
effect, you must set either -F1\Q1 or -F1\Q4.
:T12=n Secondary XOFF Flow Control Character
Where n is a decimal from 0 to 255, representing an 8-bit
character. Default is FB hexadecimal (or 251 decimal).
Defines the character used for secondary XOFF flow control on
the modem serial port. For secondary flow control to take effect,
you must set either -F1\Q1 or -F1\Q4.
:T14=n Connect Message Delay Timer
Where n is an integer from 0 to 255, in 100 millisecond interval.
Default is 0.
Specifies how long to wait before or after a connect message
before CTS, DSR, DCD go high. Use this command with @Cn
(where n=0 or 1).
:T15=n V.24 Control Register
Where n is an integer from 0 to 255 (see below for the valid
values for n). Default is 149.
This command is bitmapped and used as follows:
7-54
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
Table 7-14 T15 Command Settings
Bit
Position
Function
1
2
not used
0
1
RTS is ignored while not connected when &R0 or &R2 set
CTS follows RTS when not connected when &R0 or &R2
set
3
4
6
not used
not used
0
1
0
1
CD follows link negotiation connection status
CD always follows modem carrier when &C1 is set
V.32 answer tone without phase reversals
V.32 answer tone with phase reversals
7
:T16=n CTS Turn On Delay Timer
Where n is an integer from 0 to 255 (in increments of 12.5
milliseconds). Default is 0.
After DCD and/or DSR have been turned On while connecting,
determines how long the modem waits before turning On CTS.
:T17=n V.32/V.32bis Connection Training Timer
Where n is an integer from 0, 1, 5 to 32.
Default is 0, use dynamic training sequences - equivalent to a
setting of 28.
Controls the length of the training sequences exchanged when
trying to establish V.32 and V.32bis connections.
Reduce the time required to establish a connection by setting
:T17 to a value less than 28; this increases the modem’s
sensitivity to noise on the line.
Reduce the modem’s sensitivity to noise by setting :T17 to a
value greater than 28; this lengthens the time required to make
a connection.
CSMIM-T1 Hardware Installation Guide
7-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
:T19=n Bit Mapped Register
Where n is an integer from 0 to 255 (see below for the valid
values for n). Default is 1.
This command controls MNP link control as follows:
Table 7-15 MNP Link Control
Bit
Position
Function
0
0
1
Modem keeps a non-MNP10 1200 bps connection if no
MNP link activity is received from the remote modem.
Modem disconnects a non-MNP10 1200 bps connection if
no MNP link activity is received from the remote modem
for two minutes.
:T22=n DSR Timer
Where n is an integer from 0 to 255 (in increments of 12.5
milliseconds). Default is 34 (425 milliseconds).
After DCD and/or CTS drop, :T22 identifies how long the
modem waits before DSR is dropped when disconnecting. For
example, if \D2 and &C1 are set, when DCD and CTS drop, the
modem then waits the amount of time specified by :T22 before
dropping DSR.
:T23=n Bit Mapped Register (Table 7-16)
Table 7-16 :T23 Settings
Bit
Position
Function
Decimal Value
0,1
4
not used
Rate negotiation at
start-up
1. At the start of a V.32 connection,
makes modem examine line quality
and set speed accordingly.
2. Disabled.
6,7
not used
7-56
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Registers
:T26=n Bit Mapped Register (Table 7-17)
Table 7-17 :T26 Settings
Bit
Function
Position
0
0
1
Enables 2-second billing delay.
Disables 2-second billing delay. This bit decreases connec-
tion time, but may affect attaining connections.
1
0
1
Normal answer tone length in V.32 mode.
Shortens answer tone length in V.32 mode.
:T42=n V.34/V.FC Connection Speed Selection
0
Default V.34/V.FC connection speed selection.
1
Highest V.34/V.FC connection speed selection (about 2 speeds
above default).
2
Higher V.34/V.FC connection speed selection (about 1 speed
above default).
3
4
Default V.34/V.FC connection speed.
Lower V.34/V.FC connection speed (about 1 speed below
default).
5
Lowest V.34/V.FC connection speed (about 2 speeds below
default.
Allows you to change the V.34/V.FC connection speed
according to line quality. We recommend leaving this register
at its default setting.
If you notice that your modem falling back during V.34/V.FC
connections, or that you are seldom able to make 28,800
connections, you can try the lower settings of this register.
CSMIM-T1 Hardware Installation Guide
7-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: AT Commands and Registers
7-58
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
PORT PIN/SIGNAL ALLOCATIONS
A.1 GENERAL
This appendix supplies information regarding CSMIM-T1 port pinouts,
signals and cabling.
A.2 CONSOLE PORT
The console port is used at install to configure the CSMIM-T1. In order to
access the ROM Monitor, Console Monitor and T1 Parameters, you will
need to attach a terminal to the console port.
Table A-1 RJ45 Console Port Pin/Signal Allocations
RJ45 Pin
Signal
RTS
1
2
3
4
5
6
7
8
DTR
TXD
DCD
RXD
GND
Unused
Unused
1
8
Front view
Figure A-1 RJ48C Port Receptacle
CSMIM-T1 Hardware Installation Guide
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: PORT PIN/SIGNAL ALLOCATIONS
A.3 INTERFACE PORTS
The T1 Network interface port is used to connect the T1 line to the
CSMIM-T1. The Drop/Insert interface is used to connect the CSMIM-T1
to other equipment, such as a PBX.
Table A-2 Network Interface Port Pin/Signal Allocations
Pin
1
Signal
RXD (RING)
RXD (TIP)
Unused
2
3
4
TXD (RING)
TXD (TIP)
Unused
5
6
7
Unused
8
Unused
Table A-3 Drop and Insert Interface Port Pin/Signal Allocations
Pin
1
Signal
TXD (RING)
TXD (TIP)
Unused
2
3
4
RXD (RING)
RXD (TIP)
Unused
5
6
7
Unused
8
Unused
Table A-3 describes the wiring for the following connectors:
•
•
•
•
DTE (Cabletron part number 9372074) for DB25 female
DTE (Cabletron part number 9372082) for DB25 male
DTE (Cabletron part number 9372076) for DB9 female
DCE (Cabletron part number 9372083) for DB25 female
A-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Cabletron Cables and Connectors
•
DCE (Cabletron part number 9372075) for DB25 male
Table A-4 Connector Wiring
DTE
DCE
DTE
MMJ
RJ48C
Pin
Signal
Direction
DB25 DB25 DB9
(RS423)
1
2
3
4
5
6
7
8
RTS
OUT
OUT
OUT
IN
5
4
8
DTR
8 + 6
3
20
2
6+1
2
6 DSR
5 RXD
1 DTR
2 TXD
TxD
DCD
20
2
8
4
RxD
IN
3
3
GND
Unused
Unused
GND
-
7
7
5
3+4 GND
20
4
6
4
-
5
7
Use these adapters with Cabletron part number 9360005-X or a
straight-through cable.
NOTE
A.4 ADDITIONAL CABLETRON CABLES AND
CONNECTORS
CSMIM-T1 to CSMIM-T1 Rollover Cable, part number 9360167-XX
CSMIM-T1 to RJ45 Console Connector, part number 9360166-XX
•
Connects CSMIM-T1 slave port to EMME Console to allow Network
Manager to telnet to CSMIM-T1 and access EMME local
management.
CSMIM-T1 to DB9 Console Connector, part number 9372087
•
Connects CSMIM-T1 slave port to IRM/2/3 to allow Network
Manager to telnet to CSMIM-T1 and access IRM/2/3 local
management.
CSMIM-T1 Hardware Installation Guide
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: PORT PIN/SIGNAL ALLOCATIONS
A-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
asynchronous mode register 7-50
asynchronous/synchronous time
delay 7-50
AT T17 and T26 with cellular
connections 6-6
Symbols
$B to change serial-port speeds 6-3
$D and diagnostics 6-16
%G and protocol settings 6-10
( 7-50
T2 and auto-answer 6-7
AT commands, introduction 6-3
AT$B to change
*H and cellular connections 6-6
+++ to enter command state 6-5
serial-port speeds 6-3
Numerics
AT$D and diagnostics 6-16
AT%G and protocol setting 6-10
AT&T BELLCORE calling card
prompt 7-9
AT*H and cellular connections 6-6
AT-E and 11-bit connections 6-5
ATH to hang up 6-5
10-bit data characters 7-13
10-bit data command 7-13
11-bit data characters 6-2, 7-13
11-bit data command 7-13
11-bit data connections 6-5
2-second billing delay 7-57
Self-booting without
attention sequence guard time 7-45
auto-answer and T2 6-7
a Local Ethernet Interface 2-15
auto-answer register 7-42
automatic fallback 7-20
A
ACE features 6-1
automatic speed matching 7-20
auto-reliable mode 7-10, 7-26
auto-reliable buffer command 7-6
auto-reliable fallback character 7-3
auto-reliable mode dial modifier 7-10
auto-reliable mode, set 7-25
auto-retrain command 7-13
ACE overview 6-14
adaptive packet assembly 6-15
addr command 3-3
examples 3-4
advanced channel enhancements 6-1
Adverse Channel Enhancements
overview 6-14
alternative B V.22 6-9
analog lookback register 7-47
analog loopback
B
backspace character 7-43
Backspace key 7-1
Bell 103 connect messages 6-10
Bell 103 overview 6-10
Bell 212A 7-48
local 6-17, 7-34
with self-test 6-16, 7-34
analog test commands 7-33
answer interval 7-43
Bell 212A overview 6-9
Bell/ITU-T command 7-3
BELLCORE bong
detect modifier 7-9
bidirectional flow control,
enable 7-30
answer command 7-2
answer mode dial modifier 7-8
answer mode register 7-45
answer tone length register 7-57
answer tone register 7-50
answer tone timer 7-51
CSMIM-T1 Hardware Installation Guide
INDEX-1
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
bidirectional hardware flow
control 7-31
bong detect dial modifier 7-9
boot command 3-5
command state dial modifier 7-9
command, repeat last 7-2
command:prompt 7-1
command:set 7-1
examples 3-10
commands
boot -l command 3-8
booting from Flash ROM 2-15
BOOTP 2-11
display firmware version 7-35
to change registers 7-41
to read registers 7-41
bootstrap, display version 7-36
bps rate 7-34
bps rate adjust command 7-17
bps rate, modem port 7-4
bps rate, serial 7-3
compatibilty of V.FC and V.34 6-7
compression control command 7-4
compression, data 6-14, 7-4
compromise equalizer command 7-14
config command 3-11
break transmit 7-4
configuration
break command 7-4
register 7-41
break control command 7-18
broadcast address setting 3-5
buffer delay command 7-10
buffer, setting auto-reliable 7-6
restoring default 7-40
restoring saved 7-15, 7-37
storing complete 7-37
configuration registers, read S 7-32
configuration registers, reading 7-32
configuration, store 7-37
connect message 6-21, 7-35
connect message control 7-5
connect message control,
CTS, DSR, CD 7-5
connect message delay timer 7-54
connect messages 7-35, 7-36
connect state command 7-27
Connecting CSMIM-T1
to console 2-7
connection training timer 7-55
connection speed reporting 7-36
connection training time, V.32 7-55
console monitor
display 2-15
invoking 2-15
C
calling card dial modifier 7-9
carriage return character 7-42
carrier 6-21, 7-5, 7-35, 7-43
carrier detect 7-11, 7-44, 7-48
carrier detect by command 7-5
carrier detect response time 7-44
carrier loss delay register 7-44
CD 7-5, 7-11, 7-44, 7-48
cell-side dial modifier 7-7
cellular calls, quick connect 6-6
cellular connection dial modifiers 7-7
cellular connections 6-6
cellular making connections 7-24
change value of register 7-41
change serial port speed 7-15
check parity 7-29
Console Port A-1
Console port
pin/signal allocations A-1
console port 2-7
Console terminal description 2-7
console-baud command 3-12
credit card bong detect modifier 7-9
check parity command 7-29
clear serial port speed 7-34
command state 7-9, 7-19, 7-48
command defaults, key 6-4
command echo 7-13
command echo register 7-45
INDEX-2
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
CTS 7-5, 7-11, 7-32, 7-48, 7-50
CTS control command 7-11
CTS off until connection 7-30
CTS turn-on delay timer 7-55
dial by tone 7-33
dial delay register 7-44
dial in answer mode 7-8
dial in auto-reliable
mode modifier 7-10
dial in direct mode modifier 7-10
dial in LAPM mode modifier 7-9
dial in normal mode modifier 7-10
dial in reliable mode modifier 7-10
dial method register 7-45
dial modifiers 7-7
D
data buffering by command 7-6
data carrier detect by command 7-5
Data compression 6-14
data compression 7-4
data echo 7-14
dial modifiers, operating mode 7-9
dial pause modifier 7-8
dial pause register 7-43
dial stored number command 7-10
dial tone wait for 7-8
dial tone delay modifier 7-8
dialing
pulse 7-7, 7-29
tone 7-8
dialing commands 7-7
digital loopback
local 7-34
data echo command 7-14
data length
10-bit characters 7-13
11-bit characters 7-13
data length command 7-13
DCD command 7-5
DCD command table 7-12
DCD delay timer 7-52
default settings 7-2, 7-15, 7-40
default user profile 7-40
defaults, key command 6-4
defaults, restore 7-15
delay for hang up
remote 7-34
digital loopback local 6-18
digital loopback register 7-47
digital loopback remote 6-18
digital test commands 7-33
direct mode 7-25, 7-31
direct mode dial modifier 7-10
direct mode, set 7-25
directory 7-11
after carrier loss 7-44
delay to DTR 7-50
designate default profile 7-40
designate default user profile 7-40
detect DTR command 7-11
detect phase command 7-17
Diagnostics power-up 6-2
diagnostics 6-16
disable 2-second billing delay 7-57
disable bps rate adjust 7-17
disable compromise equalizer 7-14
disable data compression 7-4
disable detect phase 7-17
disable flow control 7-30
disable guard tone 7-15
disable MNP extended services 7-18
disable rate negotiation timer 7-56
disable result codes 7-30
disable secondary flow control 7-15
diagnostics and V.23 6-8
diagnostics command 7-33
diagnostics register 7-47
diagnostics, power-up 6-16
diagnostics, start power-up 6-16
dial 7-7
delay 7-8
in answer mode 7-8
in auto-reliable mode 7-10
in LAPM mode 7-7
CSMIM-T1 Hardware Installation Guide
INDEX-3
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
disable speed matching 7-20
disconnect buffer delay
command 7-10
disconnect by command 7-16
display
enable result codes 7-30
enable secondary flow control 7-15
enable speed matching 7-20
end test in progress 7-33
enter command state with +++ 6-5
enter connect state 7-27
entering connect state 7-27
environmental requirements 1-13
equalizer control, V.23 7-28
equalizer retrain, begin 7-27
equalizer, compromise 7-14
erase command 3-13
configuration register 7-41
registers 7-32, 7-41
display connection speed 7-36
display firmware version 7-35
display modem identification 7-17
display modem settings 7-33
displaying commands 7-13
displaying registers 7-32
DSR 7-5, 7-11
error codes, long/short 7-35
error correction
DSR control command 7-11
DSR options 7-32
LAPM 7-17
MNP 7-17
DSR timer 7-56
error correction, MNP 6-14
escape code character 7-42
escape code, guard time 7-45
Ethernet
DTMF tone dial speed 7-45
DTMF tone dialing speed 7-45
DTR 7-48
control 7-11
transceiver loopback test 3-17
Ethernet address
displaying 3-3
during power-up 2-10
exclamation point 7-9
extended result codes 7-38
DTR control command 7-11
DTR delay register 7-50
dumb mode register 7-45
dynamic transmit level
adjustment 6-1
E
F
-E and 11-bit connections 6-5
echo command 7-13
factory defalts, restore 7-15
factory default settings
7-2, 7-15, 7-40
echo data command 7-14
echoing commands 7-13
EFS Key Number 1-10
fallback 7-23
fallback character, auto-reliable 7-3
fallback modulation speeds
7-23, 7-30
false abort timer 7-53
FCC Notice iv
features, modem 6-2
firmware version display
command 7-17
firmware version, display 7-35
flash dial modifier 7-9
flash memory display bootstrap 7-36
EFS Key Value, reloading 2-16
EFS Key, warning 2-14
enable 10- or 11-bit data 7-13
enable 2-second billing delay 7-57
enable bps rate adjust 7-17
enable compromise equalizer 7-14
enable data compression 7-4
enable detect phase 7-17
enable guard tone 7-15
enable MNP extended services 7-18
INDEX-4
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
independent serial/modem port
flow control 7-25
characters 7-39, 7-53, 7-54
hardware 7-30
primary XON character 7-53
secondary XON character 7-54
serial port 7-30
speeds 7-15
Industry Canada Certification
Number vi
initial boot parameters
setting addresses 3-3
installation instructions 2-1
Installing 2-5
Internet address setting 3-4
IP encapsulation setting 3-5
ITU-T
XON/XOFF 7-39
flow control characters 7-53
flow control command 7-30
flow control enabling secondary
characters 7-15
flow control, modem port 7-16
flow control, primary XOFF
character 7-53
V.21 6-2, 7-51
V.22 6-2, 7-48, 7-51
V.22bis 6-2, 7-20, 7-48, 7-51
V.23 6-2, 7-14, 7-51
half duplex 7-51, 7-52
V.23 half duplex 7-52
V.32 6-2
G
guard time, escape code 7-45
guard tone register 7-49
guard tone, disable 7-15
guard tone, set frequency 7-15
V.54 6-18, 7-34
ITU-T/Bell command 7-3
K
H
Key AT command defaults 6-4
half-duplex and V.23 6-8
handshaking in V.34 6-7
hang up delay 7-44
hang up by command 6-5, 7-16
hardware configuration
during power-up 2-9
hardware flow control
bidirectional 7-31
L
landside data connections 6-6
LAPM
connection 7-18
reliable mode 7-26
LAPM and Bell 103 6-10
LAPM connections and V.23 6-8
LAPM mode dial modifier 7-9
LAPM modes, set 7-25
last command, repeat 7-2
last number redial command 7-10
lat -d command 3-16
lat_key command 3-16
line feed character 7-43
line probing in V.34 6-7
line quality 6-7
Hayes AT command set 7-1
help command 3-14
I
IC Notice vi
identification command 7-17
ignore DTR command 7-11
image command 3-14, 3-15
examples 3-14, 3-15
image -d command 3-16
image name default 3-6, 3-14
inactivity timer command 7-34
line turnaround timer 7-52
link negotiation dial modifier 7-7
link negotiation speed command 7-17
CSMIM-T1 Hardware Installation Guide
INDEX-5
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
load/dump gateway setting 3-5
local analog loopback 6-17, 7-34
with self-test 7-34
modem features 6-2
modem port
flow control 7-16
local analog loopback by
command 6-17
speed 7-4
testing 6-17, 6-18
local analog loopback with
self-test 6-16
local analog loopback with self-test by
command 6-16
modem port data length 7-13
modem port test 6-18
modem speed connection
matrices 6-11
local digital loopback 6-18, 7-34
local digital loopback
modem-port bps rate 7-4
modulation protocols 6-7
modulation speed command 7-30
mop command 3-17
mop -d command 3-17
multiple connection attempts 6-1
multiple protocol answering
command 7-14
by command 6-18
long form result codes 7-35
long space disconnect 7-39, 7-48
loopback diagnostics and V.23 6-8
loopback register 7-47
loopback respond register 7-49
loopback test commands 7-33
lost carrier to hang up delay 7-44
multiple-protocol auto-answer 6-7
multi-protocol timer 7-51
M
N
na
manual booting description 3-5
manual dial 7-7
reset command 4-5
set command 4-5
maximum MNP block size 7-3
messages, MNP 7-24
MNP 7-3, 7-18
class connect messages 7-24
MNP 3 6-15
MNP 4 6-15
MNP 6 6-15
MNP 7 6-15
show command 4-5
negotiation in V.34 6-7
negotiation speed, link 7-17
net command 3-17
normal mode dial modifier 7-10
normal mode, set 7-25
numeric result codes 7-35
MNP 9 6-15
MNP classes 6-14
O
MNP connect messages 7-24
MNP connections and V.23 6-8
MNP error correction 6-14
MNP extended services
command 7-18
MNP result code form 7-35
MNP10 and cellular connections 6-6
mode setting matrices 6-11
O/A register 7-45
off hook, forcing with ATA 7-2
on-line status, read 7-33
operating mode command 7-25
operating mode dial modifiers 7-9
optimized data phase 6-15
option_key command 3-18
option_key -d command 3-18
INDEX-6
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
originate mode register 7-45
pulse digit command 7-37
P
Q
parity check command 7-29
parity option register 7-49
parity, set by command 7-28
pause
quick connect cellular calls 6-6
quiet answer 7-8
quiet command 7-30
quiet dial modifier 7-8
before dial 7-43
during dial 7-8
for dial delay 7-44
R
RARP 2-11
pause dial modifier 7-8
pause time for dial delay 7-44
phone line quality 6-7
ping command 3-18
point to new register 7-41
poor telephone line connections 7-17
port pin/signal allocations A-1
port speed
rate negotiation timer 7-56
reading
configuration register 7-32, 7-41
modem status 7-33
redial 7-11
redial last number command 7-10
register
commands 7-41
modem 7-4
serial 7-15
display value of 7-41
read all 7-32, 7-41
ports command 3-19
reading 7-41
power level, cellular 7-24
power levels for cellular calls 7-24
power-up
applying power 2-9
failures during 2-9
register, change value 7-41
register, read S 7-32
registers, overview 7-41
registers, point to new 7-41
registers, read all 7-41
registers, read specific 7-41
registers, reading 7-32
reliable
connection 7-5, 7-6, 7-36
link 6-21, 7-3, 7-35, 7-36
reliable mode dial modifier 7-10
reliable mode, set 7-25
remote digital loopback 6-18, 7-34
respond to 7-34
instructions 2-9
self-testing procedures during 2-9
power-up diagnostics 6-2, 6-16
power-up diagnostics, start 6-16
preferred load host setting 3-5
primary XOFF character 7-53
primary XON character 7-53
product code display 7-17
prompt 7-1
protocol command settings 6-10
protocol connection matrices 6-11
protocols used by modem 6-2
protocols, overview 6-7
pulse dial command 7-29
pulse dial modifier 7-7
pulse dialing 7-7
with self-test 7-34
remote digital loopback by
command 6-18
remote digital loopback with
self-test 6-17
remote digital loopback,
respond 6-19
pulse dialing, digits 7-37
remote test commands 7-33
CSMIM-T1 Hardware Installation Guide
INDEX-7
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
repeat dial 7-11
saved configuration
settings 7-37, 7-40
secondary XOFF character 7-54
secondary XON character 7-54
Self-booting 2-15
sequence command 3-21
examples 3-21
Serial Devices 2-8, 2-9
serial port
repeat dial command 7-11
repeat last command 7-2
reset command 7-40
reset command reference 4-5
reset modem 7-40
respond to loopback register 7-49
respond to remote digital
loopback 6-19, 7-34
restore
clear speed 7-34
factory default settings 7-40
saved configuration settings 7-40
restore factory default settings 7-15
result code form 7-35
result code register 7-45
result codes 6-20
flow control 7-25, 7-30
speed 7-17
serial port bps rate 7-3
serial port DSR/CTS control 7-11
serial port parity command 7-28
serial port test 6-17, 6-18
serial port, test 6-16
extended 7-38
long/short 7-35
MNP 7-35
on/off 7-30
result codes, extended 7-38
result codes, longhort 7-35
retrain 7-13
serial-port DCD control 7-5
serial-port flow control 7-30
serial-port speed register 7-49
serial-port speed, clear 7-34
serial-port, speed display 7-36
set command
retrain command 7-13
retrain sequence 7-27
retrain, begin 7-27
reference 4-5
setting
boot sequence 3-21
return to command state modifier 7-9
ring
broadcast address 3-5
Internet address 3-4
to auto-answer on 7-42
ring counter register 7-42
ring to auto-answer on 7-42
ROM Monitor
command syntax 3-1
commands 3-1
list of commands 3-1
RTS 7-32, 7-48, 7-50
RTS/CTS options 7-32
IP encapsulation 3-5
load/dump gateway address 3-5
preferred load host address 3-5
SLIP parameters 3-22
subnet mask 3-5
setting protocols by commands 6-10
settings, read current 7-33
short form result codes 7-35
show command reference 4-5
single cellular connection 7-7
SLIP
S
parameters 3-23
slip command 3-22
example 3-24
S registers, displaying 7-32
S registers, overview 7-41
S registers, read 7-32
INDEX-8
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
software installation
time delay
executing boot command 2-14
procedures 2-13
setting initial boot parameters 2-14
setting Internet address 2-14
speed 7-4
RTS to CTS 7-50
time delay, asynchronous/
synchronous 7-50
time delay, DTR 7-50
timer
serial port 7-15, 7-17, 7-34
speed connection matrices 6-11
speed matching 7-20
connect message delay 7-54
V.32/V.32bis 7-55
timer command 7-34
speed matching command 7-20
speed reporting 7-36
timer delay, false answer abort 7-53
timer delay, turn CD on 7-52
timer delay, V.23 half duplex
intercharacter 7-52
timer delay, V.23 half-duplex
fallback 7-51
timer for connect message delay 7-54
timer for CTS turn-on delay 7-55
timer for line turnaround 7-52
timer for V.21 and V.23 answer
tone 7-51
speed selection, V.34/V.FC 7-57
speed, setting modem port 7-4
speed, setting serial port 7-3
speeds, cellular connection 6-6
stats command 3-25
example 3-25
status, read online 7-33
store complete configuration
settings 7-37
store current configuration 7-37
stored number dial command 7-10
subnet mask setting 3-5
switching between ITU-T
and Bell 7-3
timer for V.22, V.22bis,
and V.32 7-50
tone dial modifier 7-8
tone dialing 7-8, 7-33
tone dialing DTMF speed 7-45
transmission mode
synchronous connections
and V.21 6-9
auto-reliable 7-26
synchronous framing 6-15
synchronous mode register 7-50
direct 7-25, 7-31
LAPM 7-26
transmission mode register 7-50
transmit break 7-4
TST indicator 7-13
T
T registers, displaying 7-32
T registers, overview 7-41
telephone line quality 6-7
telephone numbers dialing 7-7
test
U
universal link negotiation 6-15
user profile store 7-37
user profile. designate default 7-40
Ethernet transceiver loopback 3-17
printer port 3-19
serial line ports 3-19
test command 7-33
test timer register 7-47
TFTP 3-8
V
V.21 6-2, 7-51
V.21 overview 6-9
V.21 timer 7-51
CSMIM-T1 Hardware Installation Guide
INDEX-9
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
V.22 6-2, 7-48, 7-51
V.22 overview 6-9
X
XON character 7-53
V.22, V.22bis, V.32 timer 7-50
V.22bis 6-2, 7-48, 7-51
V.22bis overview 6-9
V.23 6-2, 7-51
XON/XOFF flow control 7-16, 7-39
XON/XOFF pass-through 7-39
XON/XON, enable 7-30
equalizer control 7-28
half duplex 7-28, 7-51, 7-52
V.23 half-duplex 6-8
V.23 intercharacter delay timer 7-52
V.23 line delay timer 7-52
V.23 mode command 7-14
V.23 protocol 6-8
V.24 control register 7-54, 7-56
V.32 6-2
V.32 training time 7-55
V.32/V.32bis connection training
timer 7-55
V.32/V.32bis training time 7-55
V.32bis 7-55
V.32bis cellular connections 6-6
V.32bis overview 6-8
V.34 overview 6-7, 6-8
V.34/V.FC speed selection 7-57
V.54 6-18, 7-34
V.54 and V.23 6-8
V.8 command 7-20
V.8 handshaking 6-7
V.FC (V.fast Class) overview 6-7
V.FC/V.34 compatibility 6-7
verbose result codes 7-35
W
wait
before dialing 7-8, 7-43
for carrier after dial 7-43
for dial tone before dialing 7-44
for hang up after carrier loss 7-44
for quiet answer 7-8
wait before dial 7-43
wait for carrier after dial 7-43
wait for dial tone 7-8
wait for quiet modifier 7-8
INDEX-10
CSMIM-T1 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|