This manual should only be
used for Elite Tactical Riflescopes
with illuminated reticles:
Illuminated Mil Dot Tactical Reticle
BTR-Mil™ Bushnell Tactical Reticle
BTR-1™ Bushnell Tactical Reticle
BTR-2™ Bushnell Tactical Reticle
PROUD USA COMPANY
03-13
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Page #
Contents
Using the BTR-2 First Focal Plane Tactical Reticle Tactical Reticle
22
(ET1624J / ET18524)
Using the BTR-2 Second Focal Plane Tactical Reticle Tactical Reticle
(ET1624SJ )
24
Maintenance and Storage
26
27
28
29
30
Mil Dot Appendix: Using Mil Dot Reticles for Ranging
Mil Dot Appendix: Converting Trajectory Data to Mil Holdovers
Mil Dot Appendix: Cartridge Table Example
Mil Dot Appendix: Using Mil Dot Reticles for Holdover
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS GUIDE
Brightness Dial
w/ Battery Cover
Elevation Target Turret
Side Focus Adjustment
Fast Focus Eyepiece
Power Change Ring
Windage Target Turret
Models with Side Focus (3-12x44, 6-24x50)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS GUIDE
Elevation Adj. (T-Lok)
Brightness Dial
w/Battery Cover
Fast Focus Eyepiece
Power Change Ring
Elevation Adj.
Windage Adj. (T-Lok)
1-8.5x24
Brightness Dial
w/Battery Cover
1-6.5x24
(w/Finger touch
adj. caps)
Windage Adj.
Models w/o Side Focus
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FAST FOCUS EyEPIECE
The fast-focus eyepiece dial is found on the ocular end of the Bushnell Elite Tactical Riflescope. Use this adjustment to obtain a
reticle image that appears sharp to your eyes. If adjustment is needed, look at a distant object for several seconds without using your
scope. Then, shift your vision quickly, looking through the scope at a plain background. Turn the fast-focus eyepiece dial clockwise
or counterclockwise until the reticle pattern is sharp and clear. The eyepiece has a large adjustment range and should be used in
conjunction with the side focus (parallax) adjustment* to obtain maximum resolution when viewing targets at long ranges (*on high
power scopes that provide it).
POWER ChANGE RING
Changing the magnification of the Bushnell Elite Tactical Riflescope can be accomplished by grasping the
knurled knob marked with the scope’s magnification range (located on the far end of the ocular bell end).
Turn the power change ring clockwise for higher magnifications, counterclockwise for lower magnifications.
The magnification setting can be identified by noting the number that is in front of the stationary dot on the
scope tube.
SIDE FOCUS (high power models only-see Parts Guide)
The Side Focus adjustment corrects Parallax error. Parallax error is experienced when the intended target and the reticle are not on the
same focal plane.The side focus adjustment relocates an optical element within the scope, manipulating the incoming image to appear
on the same focal plane as the reticle within the riflescope, thus eliminating parallax error. Parallax error results in inconsistencies
regarding point of impact. This can be best experienced by looking at a 100 yard target with the side focus set to 500 yards. While
slightly moving your head left and right, or up and down, you will notice movement at the location where the crosshairs intersect.
However, if you change your side focus adjustment to 100 yards while looking at the 100 yard target, the intersection of the crosshairs
will not move.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Please note the distance markings on the dial are intended as reference points only. Exact side focus adjustments may be needed after
making adjustments to the eyepiece in order to achieve a high resolution, parallax free image.
FIRST FOCAL PLANE AND SECOND FOCAL PLANE RETICLES
Some models of Bushnell Elite Tactical Riflescopes described this manual have their illuminated reticles located in the first focal plane,
while others place the reticle in the second focal plane. If the reticle is within the first focal plane, it will increase in size when the
magnification is increased. This feature allows the continued use of the mil measurement system contained in the reticle, regardless
of the power setting. Second focal plane reticles restrict the user to making measurements at a specific power, as the reticle remains
the same size regardless of the magnification level.
BORE SIGhTING AND ZEROING ThE SCOPE
Bore sighting is a preliminary procedure to achieve proper alignment of the scope with the rifle bore. It is best done using a Bushnell
Bore Sighter. If a bore sighter is not available, it can be done as follows: Remove the bolt and sight through the gun barrel at a 100 yard
target. Then sight through the scope and bring the crosshairs to the same point on the target using the turrets or windage adjustments.
Return the bolt and prepare to shoot down range at the 100 yard target.
Your next step will be to zero the scope using live rounds. Fire your first shot and note the location of impact. You can use the elevation
and windage adjustments to change the point of impact accordingly. For example, if your first shot went 1 mil high and 1 mil left, adjust
your elevation dial down 1 Mil and your windage dial 1 mil right. Always adjust in the opposite direction from your point of impact.
As you fire your second shot, you should see the point of impact hit closer to your intended target. Multiple rounds may need to be fired
before achieving consistent results. You may also use reticle within your scope to help decipher the correct adjustments. The following
page shows how this works, using the BTR-Mil reticle as an example.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
In the example to the left using the BTR-Mil reticle, the shooter was
attempting to hit a target in the center of the crosshairs. The actual point
of impact hit 4 Mils down and 3 Mils left, as indicated by the red dot.
Adjust the elevation dial 4 Mils up/windage dial 3 Mils right. Another way
to accomplish this is to return the weapon to the original aiming point
on the target. Ensure that it is securely held in place. While holding the
weapon steady, adjust the elevation knob until the horizontal cross hair
intersects the bullet hole made by the first shot. Then adjust the windage
knob until the vertical cross hair intersects the original bullet hole. The
rifle scope should now be closely aligned with the bore of the weapon.
It is advisable to fire additional shots as some fine adjustments may be
required to insure that the firearm is perfectly zeroed.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ELEvATION AND WINDAGE TARGET TURRETS (3-12x44 & 6-24x50 MODELS)
Selected models of Bushnell Elite Tactical Riflescope with illuminated reticle feature target style adjustment turrets, which provide
audible and visual references. The turrets can be rotated in either direction to make appropriate adjustments.
Each turn of the turret provides an audible “click” which coincides with a movement of the visible reference point on the turret knob.
Additionally, clicks can be felt by your fingers as the turret knob moves. Each “click” represents .1 mil of reticle movement.
Rotate the elevation turret knob counterclockwise to move the reticle plane up, or clockwise to move it down. Rotate the windage dial
counterclockwise to move the reticle plane right, or clockwise to move it left. These Bushnell Tactical Riflescopes provide 5 mils of
adjustment per complete revolution of the turret.
After adjustments have been made, you can reset the turret to zero by following the procedure below:
REMOVING THE TARGET TURRETS
Using the included Allen wrench (hex key), loosen the turret bolt (A) by turning it counter-clockwise while firmly holding the turret in
place. You can either remove the bolt entirely (B), or just loosen it enough to be able to pull up on the turret and rotate it freely in either
direction (make sure the adjustment itself does not change-you don’t want to loose your zero setting).
RESETTING THE DIALS TO ZERO
Once the turret bolt is loose (or removed), and you are able to pull up the elevation turret and rotate it freely, line up the “0” on the
adjustment scale with the index line, then push the turret back down into place (C). Be careful not to lose any clicks when pushing the
turret back down, which might affect your targeting at the next use. Replace the turret bolt and use the Allen wrench to tighten it (turn
clockwise) until the turret is securely in place. Repeat this process with the windage turret.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Adjustment Scale
Index Line
C
B
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ELEvATION AND WINDAGE FINGER TOUCh ADJUSTMENTS (1-6.5x24 MODELS)
1-6.5x24 models of the Bushnell Elite Tactical Riflescope with illuminated reticle feature finger-adjustable, audible-click elevation
and windage adjustments. To adjust the elevation or windage:
1. Remove the covers from the Elevation and Windage Adjustments.
2. Grasp the Adjustment Knob and turn it in the appropriate “UP” (and/or “R”) direction indicated by the arrows. Each “click”
will change the bullet impact by .1 mil or approximately .360 inches at 100 yd. One full revolution of the turret will move the
reticle 10 mils.
RESETTING THE ADJUSTMENT SCALE RING
This step is not necessary, but, for future reference, you may want to realign the zero marks on the Adjustment Scale Rings with
the index dots. Simply pull the finger adjustment knob fully to the up position so that it disengages the turret splines- it should
rotate freely without any audible clicks. Then rotate it back to “0” and re-seat so that the knob re-engages.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ELEvATION AND WINDAGE T-LOK™ TURRETS (ET18524)
The model# ET18524 Bushnell Elite Tactical Riflescope features T-Lok™ (locking) turrets, which provide audible and visual references.
When a turret is lifted (elevated) into the upward position it can be rotated in either direction to make appropriate adjustments.
Each turn of the turret provides an audible “click” which coincides with a movement of the visible reference point on the turret knob.
Additionally, clicks can be felt by your fingers as the turret knob moves. Each “click” represents .1 mil. After adjustments are made,
the turret can be pushed back into the downward position to prevent movement, or left elevated and ready for further adjustments if
preferred.
With the turrets pulled fully upward, rotate the elevation turret knob counterclockwise to move the reticle plane up, or clockwise to move
it down. Rotate the windage dial counterclockwise to move the reticle plane right, or clockwise to move it left. These Bushnell tactical
riflescopes provide 10 mils of adjustment per complete revolution of the turret. .
After adjustments have been made, you can reset the turret to zero by following the steps below (see photos on next page):
1. Ensure the turret is in the lock position.
2. Use a coin or flathead screwdriver to remove the turret screw found on top of the turret knob, being careful not to displace the
o-ring found under the turret knob.
3. Remove the turret knob and return it to the turret, with the “zero” mark on the knob lining up with the vertical index line on the
turret.
4. Return turret screw to top of knob and tighten down, making sure the turret knob is in the locked position so the turret knob does
not turn while tightening the screw.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ELEvATION AND WINDAGE T-LOK™ TURRETS (ET18524)
STEP 2
STEP 1
STEP 4
STEP 3
13
Download from Www.Somanuals.com. All Manuals Search And Download.
USING ThE MIL DOT RETICLE (ET3124F / ET6245F)
Your Bushnell riflescope contains a mil-dot reticle (1st focal plane), the most accurate means of range estimation using a manual
optical device. These mil dots also allow precise leads for moving targets and exact compensation for shooting in a crosswind.
RETICLE DESCRIPTION
The middle of this reticle contains four evenly spaced mil-dots arrayed outward vertically and horizontally from the center. Actually, because
the very center dot was left out to allow clear aiming, the reticle represents five mils in any direction -- ten vertical mils -- as shown in the
illustration. Note that the most outward dot is replaced by the edge of the heavier reticle line.
One mil is the space from center-dot to center-dot. One-half and one-quarter mils are easy to estimate mentally; with practice, you can
measure tenths of mils for the most exact ranging.
RANGING WITH YOUR MIL-DOT RETICLE
The mil is an angular measurement -- 1/6400th of a circle -- which equals almost precisely one yard at 1000 yards, or one meter at 1000 meters.
This proportional relationship makes possible a simple formula to compute distances:
The Measured Object’s Width or Height in Yards x 1000
=
Range in Yards
Object’s Width or Height in Mils
This formula works equally well with meters, but don’t mix meters and yards: Measure the object in yards to find the distance in yards, use
meters to yield distances in meters.
Looking through your scope, select an object at the distance you want to range -- an object whose width or height you know or can estimate
accurately. Man-made objects of uniform size, such as fenceposts, are best, but any object of known dimensions will do. Measure the object’s
14
Download from Www.Somanuals.com. All Manuals Search And Download.
height or width carefully in mils, compute it according to the formula and you will find its range. Support your rifle and be precise when
measuring objects; any measuring error causes an error in the computed range. Equally, a mistake in estimating the object size results in a
proportional range error.
Here’s an example: A coyote is sunning himself in a snowfield beside a fencepost; having crossed the fence earlier, you know that the post is
four feet high, or 1.33 yards. The fencepost measures 2.5 mils in your reticle.
1.33 yards x 1000
2.5 mils
1330
2.5
=
=
532 Yards
CALCULATING HOLDS FOR WIND AND MOVING TARGETS
Your horizontal mil dots provide a precise way of holding for crosswinds and target
movement. Just look in your cartridge’s wind drift and moving target tables to determine
the exact holds for different distances. The example table (see pg. 17) lists one-mil widths
from 100 to 500 yards, so you can calculate how many mils to hold right or left when firing
in a crosswind, or engaging a moving target.
1 Mil
One mil is the distance between centers of dots. It’s easy to measure in half-mils or
even quarter-mils but with practice you can measure tenths of a mil.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
The Mil Dot Reticle Measurement System in the First
Focal Plane Applies at any Magnification Level.
2 Mils at 3.5x
(100 yards)
2 Mils at 12x
(100 yards)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
USING ThE BTR-MIL™ BALLISTIC TACTICAL RETICLE (ET3124FJ / ET6245FJ)
The Bushnell BTR-Mil™ Ballistic Tactical Reticle is a hashmarked reticle that uses mrad based
subtension lines for ranging, holdover and windage corrections.The illuminated 1 mil diameter
circle with .1 mil center dot provides an unobstructed view of the target with 10 illumination
settings.
In order to facilitate accurate holdover and windage compensation, this reticle uses hash
marks spaced in 1 mil increments with .5 mil graduations. It provides a total of 10 mils of
holdover below the center dot on the vertical crosshair and a total of 10 mils of subtension
lines on the horizontal crosshair. There are also more precise subtensions of .2 mils on the
last mil hash on both outer ends of the horizontal crosshair and on the bottom of the vertical
crosshair. The BTR-Mil reticle features an illuminated center dot that spans approximately .1
mil and marks the imaginary intersection of the horizontal and vertical stadia lines. This dot
is enclosed by an illuminated ring that subtends 1 mil. The thickness of this illuminated ring
is .14 mils.
Because the BTR-Mil reticle is positioned in the first focal plane (FFP), reticle measurements
can be used with the scope set at any magnification.
To increase the brightness of the illuminated ring, set the brightness adjustment control
(located near the eyepiece-see pg. 5) to a higher number (opposite the white index dot).To turn
off the illumination and when storing the scope, set the dial to”OFF” To replace the battery,
remove the cap on the brightness adjustment control knob using a coin, and insert a CR2032
battery with the “+” mark facing up (pg. 19, Fig. 2).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
USING ThE BTR-1 TACTICAL RETICLE IN A FIRST FOCAL PLANE SCOPE (ET1624F)
Elite Tactical model ET1624F with the BTR-1 Tactical Reticle is designed to be sighted-in at 100 yards (or meters), and provides hold
over points out to 600 meters.This reticle is calibrated for use with 223 Rem/5.56 ammunition loaded with 55-62 grain bullets. Because
the BTR-1 reticle is located in the first focal plane (FFP) position in this model, it will be accurate for all targets at any magnification
setting. It also features an illumination control dial with 11 brightness settings, including 2 positions for use with night vision units.
how To Use the Reticle:
Once zeroed at 100 yards/meters, the center dot of the BTR-1 reticle is used for shots out to 200 meters, based on the 5.56/.223 Rem
caliber. Below the center dot, you will find a series of four upside down “T’s” that represent 300, 400, 500, and 600 meter ranges.
The “T’s” are used as a bracketing system to best fit a 12”x18” target. When acquiring your target, find the best fit bracket and send
your shot. With the reticle in the first focal plane your shot can be taken at any magnification range. The versatility of the reticle can be
clearly seen as the center horseshoe dot shrinks down to a single aiming point on low power, perfect for close range shooting scenarios.
Illuminated Reticle Features
The BTR-1 reticle is illuminated.The “third knob” along with elevation and windage turrets is a brightness adjustment control (not a side
focus knob), numbered from 0 to 11 (see Fig. 1, next page). To increase the brightness, set the control to a higher number (opposite
the white index dot). To turn off the illumination and when storing the scope, set the dial to any of the “Off” positions (dots) between
each numbered illumination setting. To replace the battery, remove the cap on the brightness adjustment control knob using a coin, and
insert a CR2032 battery with the “+” mark facing up (Fig. 2).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 1
100 METERS/YARDS
300 METERS
400 METERS
Fig. 2
500 METERS
600 METERS
Note: the scope should be zeroed at 100 Meters/yards
19
Download from Www.Somanuals.com. All Manuals Search And Download.
USING ThE BTR-1 TACTICAL RETICLE IN A SECOND FOCAL PLANE SCOPE ( ET1624SF)
Elite Tactical model ET1624SF with the BTR-1 Tactical Reticle is designed to be sighted-in at 100 meters/yards, and provides hold
over points out to 600 meters. This reticle is calibrated for use with 223 Rem/5.56 ammunition loaded with 55-62 grain bullets. The
reticle design allows accurate aiming points out to 600 meters. It also features an illumination control dial with 11 brightness settings,
including 2 positions for use with night vision units.
how To Use the Reticle:
Once zeroed at 100 yards or meters, the center dot of the BTR-1 reticle is used for shots out to 200 meters, based on the 5.56/.223
Rem caliber. Below the center dot, you will find a series of four upside down “T’s” that represent 300, 400, 500, and 600 meter ranges.
The “T’s” are used as a bracketing system to best fit a 12”x18” target. When acquiring your target, find the best fit bracket and send
your shot. With the reticle in the second focal plane, the scope must be set at 6.5x magnification to insure the accuracy of the holdover
points.
Illuminated Reticle Features
The BTR-1 reticle is illuminated.The “third knob” along with elevation and windage turrets is a brightness adjustment control (not a side
focus knob), numbered from 0 to 11 (see Fig. 1, next page). To increase the brightness, set the control to a higher number (opposite
the white index dot). To turn off the illumination and when storing the scope, set the dial to any of the “Off” positions (dots) between
each numbered illumination setting. To replace the battery, remove the cap on the brightness adjustment control knob using a coin, and
insert a CR2032 battery with the “+” mark facing up (Fig. 2).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 1
100 METERS/YARDS
300 METERS
400 METERS
Fig. 2
500 METERS
600 METERS
Note: the scope should be zeroed at 100 Meters/yards
21
Download from Www.Somanuals.com. All Manuals Search And Download.
USING ThE BTR-2 TACTICAL RETICLE IN A FIRST FOCAL PLANE SCOPE (ET1624J / ET18524)
The BTR-2 reticle in first focal plane is an excellent choice for shooters needing maximum flexibility in a riflescope. This reticle in
the first focal plane combines the close range benefits of a red dot sight with the long range capabilities offered by mrad based
ranging reticle. The center horseshoe provides an unobstructed aiming point that is effective in both CQB scenarios and if targets are
encountered at longer ranges. At high magnification (6.5x or 8.5x) the mil hash vertical stadia offers 10 mils of elevation. Additionally
the horizontal stadia can be used for windage holds or to range 10” targets out to 800 meters. (See horizontal stadia detail, right).
The reticle also features an illumination control dial with 11 brightness settings, including 2 positions for use with night vision units.
how To Use the Reticle:
1. Sight in at 100 meters/yds on any magnification setting.
2. Determine distance to target. For the best accuracy in determining distance, utilize a Bushnell Laser Rangefinder (Scout DX 1000
ARC, G Force 1300 ARC).
3. Set the scope to any magnification and determine holdovers in mils based on the ballistics of your weapon.
Illuminated Reticle Features
The BTR-2 reticle is illuminated. The “third knob” along with elevation and windage turrets is a brightness adjustment control (not a
side focus knob), numbered from 0 to 11 (Fig. 1, p.21). To increase the brightness, set the control to a higher number (opposite the
white index dot). To turn off the illumination and when storing the scope, set the dial to any of the “Off” positions (dots) between each
numbered illumination setting. To replace the battery, remove the cap on the brightness adjustment control knob using a coin, and
insert a CR2032 battery with the “+” mark facing up (Fig. 2, p.21).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Center dot measures .3 mils at highest power setting (6.5x or 8.5x, depending on model)
BTR-2 @ 6.5x
BTR-2 @ 1x
23
Download from Www.Somanuals.com. All Manuals Search And Download.
USING ThE BTR-2 TACTICAL RETICLE IN A SECOND FOCAL PLANE SCOPE (ET1624SJ)
The BTR-2 reticle in second focal plane is an excellent choice for shooters needing maximum flexibility in a riflescope.This reticle in the
second focal plane combines an illuminated red dot with a mil hash platform. The center horseshoe provides an unobstructed aiming
point that is effective in both CQB scenarios and if targets are encountered at longer ranges. At 6.5 magnification power the mil hash
vertical stadia offers 10 mils of elevation, with .5 mil hash marks in between. Additionally the horizontal stadia can be used for windage
holds or to range 10” targets out to 800 meters. (See horizontal stadia detail, right). The reticle also features an illumination control dial
with 11 brightness settings, including 2 positions for use with night vision units.
how To Use the Reticle:
1. Sight in at 100 yds at the 6.5x magnification setting.
2. Determine distance to target. For the best accuracy in determining distance, utilize a Bushnell Laser Rangefinder (Scout DX 1000
ARC, G Force 1300 ARC).
3. Ensure that the scope is set at 6.5x magnification and determine holdovers in mils based on the ballistics of your weapon.
Illuminated Reticle Features
The BTR-2 reticle is illuminated. The “third knob” along with elevation and windage turrets is a brightness adjustment control (not a
side focus knob), numbered from 0 to 11 (Fig. 1, p.21). To increase the brightness, set the control to a higher number (opposite the
white index dot). To turn off the illumination and when storing the scope, set the dial to any of the “Off” positions (dots) between each
numbered illumination setting. To replace the battery, remove the cap on the brightness adjustment control knob using a coin, and
insert a CR2032 battery with the “+” mark facing up (Fig. 2, p.21).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Your Bushnell Elite Tactical riflescope, though amazingly tough, is a precision instrument that deserves reasonably cautious care.
1. When cleaning the lenses, first blow away any dry dirt and dust, or use a soft lens brush. Fingerprints and lubricants can be wiped off
with lens tissue, or a soft clean cloth, moistened with lens cleaning fluid. Microfiber cleaning cloths are also recommended.
WARNING: Unnecessary rubbing or use of a coarse cloth may cause permanent damage to the lens coatings.
2. All moving parts of the scope are permanently lubricated. Do not try to lubricate them.
3. No maintenance is needed on the scope’s outer surface, except to occasionally wipe off dirt or fingerprints with a soft cloth.
4. Use lens covers whenever it is convenient.
STORAGE
•
Avoid storing the scope in hot places, such as the passenger compartment of a vehicle on a hot day. The high temperature could
adversely affect the lubricants and sealants. A vehicle’s trunk, a gun cabinet or a closet is preferable.
Never leave the scope where direct sunlight can enter either the objective or the eyepiece lens. Damage may result from the
concentration (burning glass effect) of the sun’s rays.
•
26
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX: MIL DOT RANGING & HOLDOVER EXAMPLES
USING MIL DOT RETICLES FOR RANGING
The Equations:
Size of target in yards X 1000
Size of Target in Mils
= Range in Yards
= Range in Yards
= Range in Meters
Size of target in inches X 27.778
Size of target in Mils
Size of target in inches X 25.4
Size of target in Mils
Example 1: Looking through the riflescope, I located a preset target that has a known size of 12”x12” square. By using the Mil Dots I
measured the target to have a Mil reading of 1. What is my distance to the target?
Known size of target: 12”x 12”
Mil Reading: 1Mil
12 X 27.778
1 Mil
= 333.33 Yards
27
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX: MIL DOT RANGING & HOLDOVER EXAMPLES
Example 2: Take the same size target but now the Mil reading is .75 (from crosshair intersection to bottom of first Mil Dot).
Known size of target: 12”x 12”
Mil Reading: .75 Mil
12 X 27.778
= 444.44 Yards
.75 Mil
CONvERTING TRAJECTORy DATA TO MIL hOLDOvERS
To calculate holdovers you must first obtain your round’s trajectory data. Look at the ammunition manufacturer’s website, in a
manufacturer’s brochure, or use a ballistic software program. You will need the Bullet Path data for a 100-yard zero, in hundred-yard
increments.
The following ballistic information example refers to the Federal .308 168-gr. BTHP Match Round and a 100-yard zero. The left column
lists the cartridge’s trajectory in inches at 100-yard increments. The next column contains the mil-size in inches at these same
distances. Divide the trajectory by the mil size at each distance to find the holdover in Mils.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX: MIL DOT RANGING & HOLDOVER EXAMPLES
FEDERAL .308 168-GR BThP hOLDOvERS FOR A MIL-DOT RETICLE
(Cartridge Table Example)
Distance
100 Yards
200 Yards
300 Yards
400 Yards
500 Yards
Trajectory
0
1 Mil Size
0 Mils
Actual holdover
0 Mils
4.5”
7.2 Mils
10.8 Mils
14.4 Mils
18.0 Mils
.62 Mils
Trajectory
15.9”
35.5”
64.6”
1.47 Mils
2.46 Mils
3.58 Mils
Mil Size at given Distance
29
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX: MIL DOT RANGING & HOLDOVER EXAMPLES
USING MIL DOT RETICLES FOR hOLDOvER
MIL vALUE
IN INChES
Once you know how to range your target with a Mil Dot reticle, and using the previous
example, you can use the reticle instead of the turrets to make adjustments with holdover. For
example, your range tells you that the 12” target is 300 yards away, (12”*27.778) / (1.1Mil).
Based on the Federal .308 Win ballistic info in the previous example, you will need to hold 1.47
Mils down on the vertical crosshair and fire.
yARDS
100
200
300
400
500
600
700
800
900
1000
3.6
7.2
10.8
14.4
18.0
21.6
25.2
28.8
32.4
36.0
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ELITE® LIFETIME LIMITED WARRANTy
We are so proud of our Bushnell® ELITE® Tactical Riflescopes that their materials and workmanship are warranted to be free of defects for the life of the ELITE Tactical Riflescope.The warranty
is available to any owner of the ELITE Tactical Riflescope. No receipt or warranty card is required. This warranty does not cover damages caused by misuse or improper handling, installation or
maintenance of the riflescope.
At our option, we will repair or replace any defective ELITE Tactical Riflescope, which shall be your sole remedy under this warranty. In no event shall we be liable for transportation costs to us, costs
of removal or reinstallation of the riflescope, or incidental or consequential damages. Some states do not allow the exclusion of limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. No agent, representative, dealer or unauthorized employee of Bushnell has the authority to increase or alter the obligation of this warranty. Any return
made under this warranty must be accompanied by the items listed below:
1. Name and address for product return
2. An explanation of the defect
3. You are responsible for transport of the defective product, but we will pay for shipping the repaired or replacement product back to you anywhere in the continental United States.
4. Product should be well packed in a sturdy outside shipping carton, to prevent damage in transit, to the following address:
In U.S.A. Send To:
Bushnell Outdoor Products
Attn.: Repairs
In Canada Send To:
Bushnell Outdoor Products
Attn.: Repairs
9200 Cody
Overland Park, Kansas 66214
25A East Pearce Street, Unit 1
Richmond Hill, Ontario L4B 2M9
For products purchased outside the United States or Canada please contact your local dealer for applicable warranty information.
In Europe you may also contact Bushnell at:
Bushnell Germany GmbH
European Service Centre
Mathias-Brüggen-Str. 80
D-50827 Köln
GERMANY
Tel: +49 221 995568-0
Fax: +49 221 995568-20
This warranty gives you specific legal rights.
You may have other rights which vary from country to country.
©2013 Bushnell Outdoor Products
31
Download from Www.Somanuals.com. All Manuals Search And Download.
For further questions or additional information please contact:
Bushnell Outdoor Products
9200 Cody, Overland Park, Kansas 66214
(800) 423-3537
©2013 Bushnell Outdoor Products
Download from Www.Somanuals.com. All Manuals Search And Download.
|