Bushnell Battery Charger PP2010 User Manual

BatteryChargers  
AA RECHARGER  
POWERCHARGER  
Quick Start Guide  
Model # PP2020/PP2010  
04-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW THE BATTERYCHARGERS WORK  
The PowerCharger (PP2020) with internal power source (Lith-Ion battery) and  
the AA Recharger (PP2010) with removable power source (AA NiMh batteries)  
store electrical energy, so it can be used to recharge your portable electronic  
devices whenever you’re away from your home or campsite. Press the orange  
lid latch button on the side of the battery charger to access the Input and  
Output ports as shown below.  
OUTPUT-Used for charging your device(s)  
from the BatteryCharger’s internal battery  
(once charged via AC wall charger)  
INPUT-Used for charging the BatteryCharger’s  
internal battery from wall charger.  
FROM WALL CHARGER  
USB PORT  
FROM BatteryCharger  
(standard USB plug)  
OUTPUT PORT  
(standard USB plug)  
TO BatteryCharger  
INPUT PORT  
TO PORTABLE DEVICE  
(micro USB plug)  
CHARGING PORT*  
(micro USB plug)  
OUTPUTS  
* Use USB charging cable included with your  
device if this connector is not compatible.  
PP2020  
PP2010  
Field Light INPUT  
OUTPUT  
Lid Latch  
Button  
INPUT  
Field Light  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
CHARGING THE BATTERYCHARGER FROM THE WALL CHARGER  
1. (Model PP2010 only) Press the front battery pod grip (A) in until it clicks,  
then pull the battery pod (B) out of the bottom of the battery charger.  
Insert the 4 supplied AA NiMh rechargeable batteries if they are not  
already in place.  
2.  
3.  
Press the lid latch button and pull open the top of the BatteryCharger.  
Connect the USB cable to the micro-USB INPUT port from the USB port  
on the supplied AC charger (see packing list), and plug it into a wall outlet  
(100-240v).  
4.  
Press the Power button at the center of the PowerSync Power Gauge (C).  
All four LEDs on the Power Gauge (Fig. 1) will light up (for 10 min.) when  
the BatteryCharger’s internal battery has been fully charged (you may  
leave it connected to the charger overnight without risk of overcharging),  
and you’re ready to connect and charge your device.  
CHARGING YOUR DEVICE FROM THE BATTERYCHARGER  
Press the power button at the center of the PowerSync Power Gauge (C)  
to check the BatteryCharger’s charge status, then connect the supplied  
USB cable from the OUTPUT port of the BatteryCharger to your device to  
recharge it. If your device uses a non-standard type of connector, use the  
cable that came with it to connect to the BatteryCharger’s OUTPUT port.  
Check the charge indicator on your device to determine when it’s ready  
to use. The NiMh AA batteries inside the PP2010 may also be removed and  
used to power any device that operates on AA batteries (unless the use of  
rechargeable batteries is not recommended).  
STORING & TRANSPORTING THE BATTERYCHARGER  
Close the top lid when storing or transporting the BatteryCharger, to help  
keep dirt and debris out of the USB ports.  
PowerSync  
Power Gauge  
C
NiMh AA Battery Pod  
B
(PP2010 only)  
Power  
Button  
Battery Pod Grip  
A
WARNING: INSERT ONLY NiMh AA  
BATTERIES IN THE PP2010. NEVER  
ATTEMPT TO CHARGE ALKALINES  
OR LITHIUMS.  
(front side)  
(PP2010 only)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
UNDERSTANDING THE POWERSYNC POWER GAUGE  
The 4 LED charge indicators behind the Power Gauge (C) allow you to monitor  
the status of the BatteryCharger’s internal battery. While the battery is  
charging from the AC wall charger, the LEDs will light up in sequence to show  
the charge level as shown in Fig. 1. The LED indicating the current battery  
level will blink rapidly while charging. When charging is complete, all LEDs  
remain on for 10 min., then shut off until the Power button is pressed.  
Blinking  
Fig. 1  
Charging In  
from AC  
>25%  
>50%  
>75%  
>90%  
FULL  
While the BatteryCharger is charging your connected device (Power button  
must be pressed), the LEDs will monitor the BatteryCharger’s battery level as  
shown in Fig. 2, with a single LED blinking once every 15 sec. (shows active  
charging but conserves battery power).  
Slowly Blinking  
Fig. 2  
Charging Out  
to Device  
<25%  
<50%  
<75%  
<90%  
FULL  
You can also check the current level of the BatteryCharger’s battery charge  
anytime by pressing the Power button, even when it is not connected to the  
charger or an external device. The LEDs will glow steadily to indicate the  
charge level % as shown in Fig.3. , then shut off after 10 seconds.  
Blinking  
Fig. 3  
Checking  
Charge Level  
<25%  
>25%  
>50%  
>75%  
FULL  
The Field Light will glow during charging. You can also press  
the power button at any time to turn it on to help insert the  
USB cable into the Output port when you’re charging at night.  
Field Light  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
TECHNICAL SPECIFICATIONS  
Model  
Weight  
Size  
PP2020 PowerCharger  
PP2010 AA Recharger  
9.3 oz / 167 g  
7.9 oz / 153 g  
5.0 x 3.1 x 0.9 in.  
approx. 5 hrs.  
5.9 x 3.3 x 1.1 in.  
approx. 8 hrs.  
Charge Time (Wall  
Charger)  
Power Output  
5 volts, 1 amp (1000 mA)  
High Capacity Lith Ion (20 Whr)  
n/a  
5 volts, 1 amp (1000 mA)  
n/a  
Internal Battery Type  
Removable Batteries  
(included)  
4x NiMh rechargeable AA (2000ma)  
USB Inputs / Outputs  
Operating Temp. Range  
Storage Temp. Range  
1 / 2*  
1 / 1  
-4 ~ 112o F (-20~44o C)  
-4 ~ 140o F (-20~60o C)  
-4 ~ 112o F (-20~44o C)  
-4 ~ 140o F (-20~60o C)  
Recommended  
Cell Phones (inc Smartphones)/3x,  
MP3 Players/4x, Digital Cameras/7x,  
Tablet/1x Note: Tablets and other  
Cell Phones (inc Smartphones)/1x, MP3  
Players/2x, Digital Cameras/2.5x  
Note: Tablets and other devices have  
Devices/# of Charges**  
(from fully charged  
internal battery)  
devices have higher power requirements higher power requirements and may  
and may not attain a full charge from  
the BatteryCharger battery.  
not attain a full charge from the  
BatteryCharger battery.  
* Two devices may be charged simultaneously. They will not charge any slower than if only one device was connected,  
however the PowerCharger’s internal battery charge will be depleted more rapidly.  
** Rechargeable batteries in electronic devices charge at different rates, depending on many factors including temperature, age and circuit  
design. Bushnell provides examples of charges per device, based on typical product use and are not intended to be specific to any single device.  
After pressing orange lid latch button,  
carabiner clip can be opened for easy  
attachment to backpacks, belt loops, etc.  
Press clip back into place and secure latch  
before transporting.  
WARNING: MODEL PP2010 IS DESIGNED TO RECHARGE ONLY NiMh (Nickel Metal  
Hydride) AA RECHARGEABLE BATTERIES. USE ONLY THE SUPPLIED NiMh BATTERIES  
OR COMPARABLE REPLACEMENTS. NEVER ATTEMPT TO CHARGE ALKALINE OR  
LITHIUM AA BATTERIES IN THE PP2010.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
ONE YEAR LIMITED WARRANTY  
Your Bushnell® POWERSYNC product is warranted to be free of defects in materials and workmanship for one year after the date of purchase.  
In the event of a defect under this warranty, we will, at our option, repair or replace the product, provided that you return the product  
postage prepaid. This warranty does not cover damages caused by misuse, improper handling, installation, or maintenance provided by  
someone other than a Bushnell Authorized Service Department.  
Any return made under this warranty must be accompanied by the items listed below:  
1.  
2.  
3.  
4.  
5.  
A check/money order in the amount of $10.00 to cover the cost of postage and handling  
Name and address for product return  
An explanation of the defect  
Proof of Date Purchased  
Product should be well packed in a sturdy outside shipping carton, to prevent damage in transit, with return postage prepaid  
to the address listed below:  
IN U.S.A. Send To:  
Bushnell Outdoor Products  
Attn.: Repairs  
IN CANADA Send To:  
Bushnell Outdoor Products  
Attn.: Repairs  
9200 Cody  
Overland Park, Kansas 66214  
25A East Pearce Street, Unit 1  
Richmond Hill, Ontario L4B 2M9  
For products purchased outside the United States or Canada please contact your local dealer for applicable warranty information. In  
Europe you may also contact Bushnell at:  
Bushnell Germany GmbH  
European Service Centre  
Mathias-Brüggen-Str. 80  
D-50827 Köln  
GERMANY  
Tél: +49 221 995568-0  
Fax: +49 221 995568-20  
This warranty gives you specific legal rights.  
You may have other rights which vary from country to country.  
©2013 Bushnell Outdoor Products  
FCC Compliance Statement  
This device complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE. These limits are  
designed to provide reasonable protection against harmful interference in a residential installation, and are more stringent thanoutdoor”  
requirements.  
Operation of this device is subject to the following conditions; (1) This device may not cause harmful interference, and (2) this device must  
accept any interference received, including interference that may cause undesired operation.  
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
The device does not contain any user-serviceable parts. Repairs should only be made by an Authorized Bushnell repair center. Unauthorized  
repairs or modifications could result in permanent damage to the equipment, and will void your warranty and your authority to operate  
this device under Part 15 regulations.  
The shielded interface cable which is provided must be used with the equipment in order to comply with the limits for a digital device  
pursuant to Subpart B of Part 15 of FCC Rules.  
Specifications and designs are subject to change without  
any notice or obligation on the part of the manufacturer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customer Service: (800) 423-3537  
©2013 Bushnell Outdoor Products  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Box Network Hardware 10 100BASE T Ethernet Extender over VDSL2 User Manual
Black Decker Glue Gun 632900 00 User Manual
Bosch Appliances Network Card D8125INV User Manual
Bravetti Food Processor EP109HA User Manual
Cal Flame Gas Grill KD6002 User Manual
Canon Projector SX800 User Manual
Canon Scanner 4507B002 User Manual
Casio Digital Camera MA1002 B 1104 User Manual
Chicago Electric Cordless Sander 67707 User Manual
Chromalox Electric Heater STAR 05A User Manual