Fire Alarm Systems | D9124 Addressable Fire Alarm Control Panel (FACP)
D9124 Addressable Fire Alarm Control
Panel (FACP)
24 VDC, 4 A power for initiation circuits and NACs;
12 VDC, 1.4 A power for system accessories
▶
Up to eight supervised or 32 unsupervised remote
annunciators
▶
One-man Fire Test Mode
▶
▶
Schedules (Skeds function) service reminder for local
systems
Low battery, AC power supply, and battery lead
supervision
▶
▶
Dual phone line monitor
The D9124 FACP controls complex alarm systems used in
schools, universities, manufacturing plants, and health care
facilities. Program it for fire, fire supervisory, intrusion, or
access control applications. Program it locally using the
D5200CE hand-held programmer or remotely using RPS
over telephone lines or local-area or wide-area networks
(LAN or WAN).
Five system power trouble conditions are selected by DIP
switches. They can be individually linked to a central
station, or grouped to activate a trouble relay, allowing a
single supervised address to monitor the power supply.
A pair of 12 V batteries provides standby power. Two
additional batteries provide standby power for initiating
devices and notification appliances. All four batteries are
housed within the panel enclosure.
The D9124 FACP is a modular assembly, installed in a red
steel enclosure, which can be surface- or flush-mounted.
The enclosure has keyed controller access making it
suitable for installation in public access areas.
Note
Batteries are not included in the D9124 and
must be purchased separately.
Central Station Communication
Events can be communicated to a central station by the
digital communicator or by adding an optional Ethernet
interface module. The optional Bosch D6500 or D6600
Functions
Alarm Verification
2
NetCom Receiver and Modem IIIa reporting format provide
The alarm verification feature reduces potential false alarms
by requiring a reset and a second alarm signal from the
device before the control panel raises an alarm condition.
individual point reporting to monitoring facilities.
The D5500 Remote Programming Software (RPS) allows
the following to be controlled from a central station:
Auxiliary and Standby Power
Resetting notification appliances
Activating or deactivating remote annunciation
Activating or deactivating relays
Supervising battery condition
Setting point status and armed status
Enabling or disabling reporting functions
Shunting reporting points during servicing
•
The 4 A, 24 VDC power supply charges the standby batteries
and powers auxiliary devices. The power supply responds
to low battery or battery disconnect conditions with a
Trouble LED and a Trouble Relay for sounders or lights.
•
•
•
•
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
D9124 Addressable Fire Alarm Control Panel (FACP) | 3
Technical Specifications
Category
Product ID
D192G
Product Description
Bell supervision module
POPEX module
Environmental Considerations
D8125
Relative Humidity:
Up to 85%; non-condensing
D8125MUX Zonex to dual multiplex interface
Temperature (operating):
+32°F to +122°F (0°C to +50°C)
D8128D
D8129
OctoPOPIT module
Inputs
Octo-relay module
D8130
Release module
Sensor Circuits:
Up to two 8125 POPEX modules,
119 addresses per module
D9127U
D9127T
D9131A
DX4020
POPIT module (no tamper)
POPIT module (tamper)
Parallel printer interface module
Ethernet interface module
Handheld programmer
Sensor Circuit Protection:
Power limited to 4 A; short circuit, reverse
polarity, thermal overload and current over-
load protection on-board
Sensor Loop Technology:
Four-wire addressable circuits
Programming D5200CE
Products
Mechanical Properties
RPS
Remote Programming Software
Remote Programming Software
Remote Programming Software
Color:
Red
RPS-LITE
RPS-INTL
Material:
16-gauge (1.5 mm) steel
Dimensions (H x W x D)
Enclosure Box:
36.1 in. x 22.1 in. x 3.2 in.
(92 cm x 56 cm x 8.1 cm)
Parts Included
Removable Door:
37.1 in. x 23.3 in. x 1.1 in.
(94 cm x 59 cm x 2.8 cm)
The D9124 Addressable Control Panel is shipped in three
boxes. One box contains:
Outputs
Quant.
Component
Off-board relays:
Up to 16 optional D8129 Relay Modules (eight re-
lay outputs per module)
1
D9412GLTB Control Panel (less terminal blocks)
On-board NACs:
Two; 1.8 A maximum per circuit
Another box contains:
Power Requirements
Quant.
Component
Current (operating)
Alarm + sensor load:
Idle:
1
D9101 Enclosure Assembly with Door
874 mA
The third box contains a D9100 Accessory Module Carrier
that includes the following:
412 mA
Power (auxiliary):
Power (primary):
24 VDC nominal at 1.8 A
120 VAC, 60 Hz, 360 VA
Quant.
Component
2
1
1
1
D192C Indicating Circuit Supervision Modules
D928 Dual Phone Line Switcher
D8125 POPEX Module (additional optional)
D9142LC 24 VDC Power Supply
Ordering Information
D9124 Addressable Fire Alarm Control
Panel (FACP)
Up to eight supervised or 32 unsupervised re-
mote annunciators
D9124
D113
The third box also contains:
Quant.
Component
Accessories
1
1
1
1
2
2
1
1
D1256 Fire Alarm Keypad
D1601 Transformer
D113 Battery Lead Supervision Module
Supervises wiring connections for two 12 V
batteriesconnectedtothesamesetofcharging
terminals.
Wiring Harness
Wiring Harness for the D8125 POPEX Module
560 Ω Resistors (for D192C Modules)
D161 Dual Modular Telephone Cords
D162 Dual Modular Telephone Cord
Literature pack
D122 Dual Battery Harness
Harness with circuit breaker. Connects two
batteries to a compatible control panel.
D122
D135A Low‑battery Disconnect Module
Disconnects the control panel from the battery
when the battery level drops to 9.5 VDC.
D135A
Download from Www.Somanuals.com. All Manuals Search And Download.
4 | D9124 Addressable Fire Alarm Control Panel (FACP)
Ordering Information
D127 Reversing Relay Module
Reports two separate alarm conditions to the
central station.
D127
D136
D136 Plug‑In Relay
Maximum rating is 1 A at 24 VDC or 2 A at
12 VDC. Available individually (D136) or in a
package of 25 (D136‑25).
D138 Mounting Bracket, Right Angle
Used to mount accessory modules in D8103,
D8108A, and D8109 enclosures.
D138
Americas:
Bosch Security Systems, Inc.
130 Perinton Parkway
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
Asia-Pacific:
Robert Bosch (SEA) Pte Ltd, Security Systems
11 Bishan Street 21
Represented by
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
5600 JB Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
Singapore 573943
Phone: +65 6258 5511
Fax: +65 6571 2698
© Bosch Security Systems Inc. 2010 | Data subject to change without notice
T1113332363 | Cur: en-US, V5, 4 Jul 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|