Security Escort
Technical Reference
Manual
EN
Security Escort
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual |
EN | 3
Remedy
Bosch Security Systems will replace
defective media or documentation, or
correct substantial program errors at no
charge, provided you return the item
with proof of purchase to Bosch Security
Systems within 90 days of the date of
delivery. If Bosch Security Systems is
unable to replace defective media or
documentation, or correct substantial
program errors, Bosch Security Systems
will refund the license fee. These are
your sole remedies for any breach of
warranty.
Because programs are inherently complex
and may not be completely free of
errors, you are advised to verify your
work. In no event will Bosch Security
Systems be liable for direct, indirect,
incidental, or consequential damages
arising out of the use of or inability
to use the program or documentation,
even if advised of the possibility of
such damages. Specifically, Bosch
Security Systems is not responsible for
any costs including, but not limited to,
those incurred as a result of lost
profits or revenue, loss of use of the
computer programs or data, the cost of
any substitute program, claims by third
parties, or for other similar costs.
Bosch Security Systems does not
represent that the licensed programs may
not be compromised or circumvented. In
no case shall Bosch Security Systems
liability exceed the amount of the
license.
Some states do not allow the exclusion
or limitation of implied warranties, or
limitation of liability for incidental
or consequential damages, so the above
limitation or exclusion may not apply to
you.
Bosch Security Systems retains all
rights not expressly granted. Nothing in
this license constitutes a waiver of
Bosch Security Systems rights under the
U.S. Copyright laws or any other Federal
or state law.
Should you have any questions concerning
this license, write to: Bosch Security
Systems, 130 Perinton Parkway, Fairport,
New York 14450.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Table of
Contents
EN | 4
3.3.7 Communications Port Monitor ... 42
3.3.8 Delay To Ignore Troubles That
Auto Reset .......................... 42
3.3.9 Transponder Communications Screen
.............................. 42
3.3.10 Transponder Current Status
Screen .............................. 45
Table of Contents
1.0 Security Escort System
Architecture.......................... 7
1.1 System Components............... 7
1.1.1 System Overview................. 7
1.1.2 Transmitter..................... 7
1.1.3 Receiver........................ 8
1.1.4 Alert Unit...................... 8
1.1.5 Transponder..................... 9
1.1.6 Central Console................. 9
1.1.7 Software Overview............... 9
1.2 System Operation............... 10
1.2.1 Alarm Sequence................. 10
1.2.2 Test Sequence.................. 12
2.0 Setting Up The System.......... 13
2.1 Initial System Configuration... 13
3.0 System Menus and Screens....... 13
3.1 File Menu...................... 13
3.1.1 Locate Transmitters............ 13
3.1.2 Maintenance Alarm Database..... 14
3.1.3 Operator Database.............. 14
3.1.4 Reports Database............... 14
3.1.5 Subscriber Database............ 14
3.1.6 Transponder Database........... 17
3.3.11 Transponder Parameter Change
Screen .............................. 47
3.3.12 Transponder Data View Screen . 48
3.3.13 Receiver Configuration Screen 49
3.3.14 Receiver Test Screen ......... 51
3.3.15 Network Status Screen ........ 52
3.3.16 System Status Screen ......... 53
3.3.17 System Preferences Screen .... 54
3.3.18 Transponder Comm Port Setup
Screen .............................. 57
3.3.19 Remote Comm Port Setup Screen 58
3.3.20 Remote Setup Screen .......... 59
3.3.21 Remote Connection Screen ..... 60
3.3.22 Phone Book Edit Screen ....... 61
3.3.23 Pager Setup Screen ........... 62
3.3.24 Send Pager Message Screen .... 63
3.4 Printer Menu .................. 63
3.4.1 Select Alarm Printer Screen ... 64
3.4.2 Select Report Printer Screen
Screen .............................. 64
3.4.3 Print History Screen .......... 64
3.4.4 Print File Screen ............. 64
3.5 Network Menu .................. 65
3.5.1 System Directories and Network
Address Screen ...................... 65
3.5.2 Network Socket Status Screen .. 67
3.5.3 Winsock Data Screen ........... 68
3.5.4 This Computer's Name and Address
Screen .............................. 68
3.6 About Menu .................... 68
3.6.1 About Screen .................. 69
4.0 Files Required For Security
3.1.7 Creating a New Transponder Entry.
............................... 19
3.1.8 Setting Receiver Parameters.... 20
3.1.9 Transmitter Change............. 26
3.1.10 Exit.......................... 26
3.2 Utilities Menu................. 26
3.2.1 Backup Screen.................. 26
3.2.2 Restore Screen................. 27
3.2.3 Security Preferences Screen.... 28
3.2.4 System Defaults Screen......... 31
3.2.5 System Labels Screen........... 31
3.2.6 Print System Reports Screen.... 31
3.2.7 Alarm Report Generation Screen. 32
3.2.8 Schedules Screen............... 33
3.2.9 Edit Schedule Times Screen..... 34
3.2.10 View Alarm Groups Screen...... 34
3.2.1 Alarm Groups Screen............ 35
3.2.12 Alarm Group State Screen...... 35
3.2.13 Current Check-in Status Screen 36
3.2.14 Clear Screen.................. 36
3.2.15 Output Verification........... 36
3.2.16 Synchronize System Time....... 36
3.3 Setup Menu..................... 36
3.3.1 Show History................... 36
3.3.2 History Filter Screen.......... 37
3.3.3 Popup Trouble Filter........... 39
3.3.4 Transponder Troubles........... 40
3.3.5 Mux Bus Point Troubles......... 41
3.3.6 Transmitter Supervision Monitor 41
Escort .............................. 70
5.0 Image Files ................... 71
5.1 Map File Generation and Scaling 71
5.2 Multiple Map Files ............ 72
5.3 Subscriber Images ............. 72
6.0 Security Escort Pager Setup ... 72
6.1 Dial-up Paging Modem Setup .... 73
6.2 Local Paging Setup ............ 73
6.3 Service and Security (Alarm)
Pager Setup ......................... 74
6.4 Subscriber (Individual) Pager
Setup .............................. 74
6.5 Alarm Area Setup .............. 75
6.6 Manual Pages .................. 75
7.0 Importing a Subscriber Database 76
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Figures
EN | 5
Figure 33: Edit Schedule Time Screen 34
Figure 34: View Alarm Groups Screen . 34
Figure 35: Alarm Groups Screen ...... 35
Figure 36: Alarm Group State Screen . 35
Figure 37: Current Check-in Status
Figures
Figure 1:Screen Box for Password Entry
............................ 10
Figure 2:Central Console Screen During
Alarm....................... 11
Figure 3:Console Screen Showing test
Icons....................... 12
Figure 4:File Menu.................. 13
Figure 5:Locate Transmitters........ 14
Figure 6:Maintenance alarm with Signal
Levels Shown in Icons"...... 14
Screen
.................. 36
Figure 38:Setup Menu................ 36
Figure 39: History Filter Screen .... 37
Figure 40: Pop-Up Alert Showing
Receiver not Responding .... 39
Figure 41: Pop-up Trouble Filter Screen
.................. 39
Figure 7:Edit Subscriber’s Advanced
Figure 42:Transponder Communications
Features Screen............. 14
Screen
.................. 42
Figure 8:Find Transponder’s Database
Figure 43:Transponder Current Status
Screen .................. 45
Figure 44:Transponder Parameter Change
Screen .................. 47
Figure 45:Transponder Data View Screen
.................. 48
Figure 46:Receiver Configuration Screen
.................. 49
Figure 47:Abort Button to Remove a
Device from the Setup Mode . 50
Record...................... 17
Figure 9:Blank Screen Resulting from
Selecting the Insert New
Button...................... 20
Figure 10:Select Point Screen with "All
Points" Selected............ 20
Figure 11:Select Point Screen with
"Receivers Only" Selected... 21
Figure 12:Drop-Down Menu for Selection
of Point Type............... 21
Figure 13:Data Entry After Selection of
Receiver Point Type......... 22
Figure 48: Confirmation of Successful
Setup Test ................. 50
Figure 49: Receiver Test Screen ..... 51
Figure 50: Network Status Screen .... 52
Figure 51: System Status Screen ..... 53
Figure 52: System Preferences Screen 54
Figure 53: Transponder Comm Port Setup
Figure 14:Data Entry after Selection of
Alert Unit Point Type....... 22
Figure 15:Data Entry after Selection of
Virtual Receiver Point Type. 22
Figure 16:Data Entry when Show Areas is
Selected ................... 22
Screen
.................. 57
Figure 17:Drop-Down Menu for Assigning
Alert Units to Receivers.... 23
Figure 18:Location Algorithm Selection
................... 23
Figure 19:Receiver floor level
selection................... 23
Figure 20:Save Changes Screen Box... 25
Figure 21:Utilities Menu............ 26
Figure 22:Backup Screen............. 26
Figure 23: Restore Screen............ 27
Figure 24: Restore Warning Message Box.
................... 27
Figure 25:Restore Save Old database
Message Box................. 28
Figure 26: Security Preferences Screen.
................... 28
Figure 27:System Defaults Screen.... 31
Figure 28: System Labels Screen...... 31
Figure 54:Remote Port Setup Screen.. 58
Figure 55: Remote Setup Screen ...... 59
Figure 56: Remote Connection Screen . 60
Figure 57: Phone Book Edit Screen ... 61
Figure 58: Pager Setup Screen ....... 62
Figure 59: Send Pager Message Screen 63
Figure 60: Printer menu ............. 63
Figure 61: Alarm Printer Screen ..... 64
Figure 62: Report Printer Screen .... 64
Figure 63: Print File Screen ........ 64
Figure 64: Common Open File Screen .. 65
Figure 65: Network Menu ............. 65
Figure 66: System Directories and
Network Address Screen ..... 65
Figure 67: Current Network Socket
Status Screen .............. 67
Figure 68: Winsock Data Screen ...... 68
Figure 69:This Computer's Name and IP
Address Screen ............. 68
Figure 29: Print System Reports Screen.
................... 31
Figure 30:Alarm Report Generation
Screen ................... 32
Figure 31:Schedule Screen........... 33
Figure 32: Holiday selection in the
Schedule Screen............. 33
Figure 70: About Menu ............... 68
Figure 71: About Screen ............. 69
Figure 72: Remote Setup Screen ...... 73
Figure 73: Pager Setup Screen ....... 74
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Tables
EN | 6
Figure 74: Subscriber Database Advanced
Screen ................... 74
Figure 75:Transponder Area Edit Screen
................... 75
Figure 76:Send a Pager Text Message
Screen ................... 75
Tables
Table 1: Importing a Subscriber
Database ................... 77
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 1.0 Security Escort
System Architecture
EN | 7
1.0 Security Escort
nearby receiver activate, as well as
the strobes and sirens on nearby alert
units.
System Architecture
The transmitters have a second feature,
the test mode. When the user is
indoors, in sight of an interior
receiver or outdoors, in sight of an
alert unit, pressing the test sequence
performs a test (see your transmitter
User’s Manual). If the test is
1.1 System Components
1.1.1 System Overview
The Security Escort System consists of
five basic components: transmitters,
receivers, alert units, transponders,
and the central console.
successful, a small green light flashes
on the interior receiver, or the strobe
on an alert unit flashes briefly. There
is no response at all if the test
fails. If the test fails, the user
should try again. If there is still no
response, the user should contact the
security office as soon as possible.
Every successful test is recorded in
the Subscriber Database in the central
console software and optionally printed
on the hardcopy printer. The Subscriber
Database contains all of the
The transmitter is a miniature, radio
transmitter, used to transmit either a
distress or a test signal. The
receivers are located throughout a
protected area and detect the radio
transmissions from transmitters. Alert
units are siren/strobe units activated
in the event of an alarm. Transponders
are devices that control groups of
receivers and alert units, connected to
them by wire. Each transponder relays
alarm and test signals from its
receivers to the central console. In
addition, the transponder tests for
device and wiring faults, and transmits
problem conditions to the central
console. The central console consists
of a computer (the master computer), an
optional backup computer (the slave
computer). Up to eight optional
information relating to each
subscriber, including the date and time
of the most recent test transmission.
It is possible to search the Subscriber
Database for individuals who have not
performed tests for a specified period
of time.
workstation computers can be used to
receive alarm and trouble signals from
the transponders, analyze the signals,
activate strobes and sirens on the
alert units, and produce a display for
the security dispatcher. Each of these
system elements is described more fully
below.
Security Transmitter
The Security Transmitter are unique in
the way that both tests and alarms are
processed. Outwardly, Security
Transmitters perform in the same manner
as normal transmitters during testing.
That is, strobes flash on alert units
and green lights flash on receivers to
confirm a successful test. However,
when a Security Transmitter is tested
within close proximity of a receiver,
the central console records not only
the user identity, and the date and
time (as with a normal user test) but
also the location of the officer at the
time of the test. These tests are
designated by the term security test on
the printout at the central console and
provide a convenient means of recording
security patrols. (To protect user
privacy, location information is not
printed out for regular subscribers
during tests.)
1.1.2 Transmitter
There are several types of transmitters
for personal use; those normally
assigned to system subscribers, one for
security personnel, and one for
maintenance personnel. Each transmitter
type serves a different purpose. All
versions of transmitters for personal
use produce alarm and test
transmissions.
Subscriber Transmitter
Each transmitter contains a unique
code, which is associated with the
subscriber at the time the transmitter
is assigned. In the event of an
emergency, press and hold the alarm
button(s) for 1 sec. to produce an
alarm (see your transmitter user
manual). Optionally, within
The Security Transmitters also differ
in the way that alarms are managed.
Unlike regular transmitters, no sound
is emitted from the transmitter itself,
no horns are activated on receivers,
and no strobes or sirens are activated.
approximately 2 sec., the sounders in a
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 1.0 Security Escort
System Architecture
EN | 8
The console in the security office
sounds an alert tone and displays the
alarm as usual except for a yellow
background and text advising that the
event is a silent alarm from a security
officer. This allows security personnel
to call for assistance without
Each receiver contains a radio receiver
to detect the transmissions from
transmitters, and microcomputers to
decode and interpret the received test
and alarm messages. In addition, the
microcomputers monitor to detect
tampering, and report such conditions
to the transponder.
attracting unwanted attention.
Maintenance Transmitter
Each receiver contains a sounder
similar to those in self-contained
smoke detectors. These sounders are
optionally activated if the receiver
has detected an alarm transmission.
The Maintenance Transmitter is used
exclusively for system set-up and
diagnosis. Maintenance alarms are used
during the system set-up to verify that
a receiver is functioning and is
properly identified in the Transponder
Database. The maintenance alarm is also
used to measure the received signal
strength of the receivers from any
location within the protected area. The
central console distinguishes the
Maintenance Transmitter by its unique
coded message and produces a printout
of the signal strengths reported by
receivers on each transponder.
Indoor receivers are typically mounted
on inside walls. They are housed in
small beige, rectangular units. Indoor
receivers have one red and one green
light. The green light is used to
indicate a successful test of a
transmitter. The red light is only
illuminated during certain system tests
and during alarms.
Outdoor receivers are contained in
small weatherproof boxes typically
mounted on the sides of buildings and
on light posts. Outdoor receivers do
not have the visible red and green
LED’s. Outdoors, the strobe lights on
the alert units flash to acknowledge
successful tests.
In the Test Mode, the Maintenance
Transmitter behaves like a normal
Subscriber Transmitter except that the
central console does not verify the
user ID portion of the transmitted
code. Unlike the Subscriber
Transmitters, all Maintenance
Transmitters are assumed to be valid.
In addition to its radio receiver, each
receiver also contains a transmitter
functionally similar to the hand held
transmitters. This transmitter can be
commanded by the central console to
transmit a test message to other nearby
receivers. This buddy checking is
performed periodically to verify that
the receiver sections of all receiver
units are functioning satisfactorily.
Point Transmitter
The Point Transmitter is used to
protect assets not people. It has a
magnetic reed switch and a supervised
loop that reports both open and shorted
states. The software can be programmed
to report alarms and troubles on any of
these conditions going off normal with
unique text identifying the condition.
These transmitters are supervised and
also optionally support the alarm
follower.
1.1.4 Alert Unit
An alert unit consists of two
components, a self-contained
strobe/siren unit and an electronic
driver unit. The latter may be housed
in either a metal indoor enclosure or
an outdoor enclosure (similar to the
outdoor receiver enclosure), depending
on the application. The strobe siren
units are always mounted in outdoor
locations. In addition to the function
of attracting attention in the event of
an emergency, the strobe unit is used
to acknowledge a successful test of a
transmitter.
1.1.3 Receiver
The receivers are located throughout
the protected area, including building
interiors. Inside buildings, the
spacing of these devices depends on the
building construction and the locating
precision required. Outdoors, spacing
depends on terrain and foliage
conditions and building obstructions.
The procedure for location of receivers
is contained in The Security Escort
Installation Guide.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 1.0 Security Escort
System Architecture
EN | 9
The alert unit has back-up battery
power in addition to AC power. The
alert unit driver contains a
microprocessor, which communicates with
the transponder for strobe and siren
commands, status reports, and trouble
indications. The troubles monitored are
tamper, loss of AC power, and low
battery.
1.1.6 Central Console
The central console consists of one to
eight IBM PC compatible computers
running the Security Escort software
within the Microsoft Windows
environment. One computer serves as the
main controller for the entire Security
Escort System (the master computer) and
a second serves as an optional backup
(the slave computer). The other
computers serve as workstations for the
operators of the software. The slave
and workstation computers can be used
for administrative functions such as
adding subscribers or performing
routine system tests without
1.1.5 Transponder
The transponder is a device controller
for up to 64 devices; any combination
of receivers and alert units. The
devices are connected to the
transponder by means of 8 four wire
multiplex busses, two wires for power
and two wires for data. Each bus is
capable of supporting up to eight
devices. The Security Escort System
supports up to 255 transponders.
interfering with the operation of the
master computer.
In the event of an alarm from a
transmitter, the console displays the
name of the individual to whom the
transmitter is assigned, and the
location from which the transmission
was made. The location information is
shown graphically on a map of the
protected area. Other information about
the subscriber, such as address, home
address, phone number, and any
Each receiver and alert unit is
identified to its transponder by a
multiplex address that is set during
system installation using a multi-
position switch on the receiver or
alert unit circuit board. Transponders
communicate on the data bus with
individual multiplex devices by issuing
commands, which contain the receiver or
alert unit’s multiplex address. Note
that a given transponder may have up to
eight devices with the same binary
multiplex address, one on each bus.
Thus, the complete identification of a
particular device must include the
transponder with which it is associated
(1 to 255), the bus on which it is
located (0 to 7), and its binary
multiplex address (0 to 7).
disabilities may also be shown.
Both the main computer and the backup
record all messages sent between the
central console and the transponders,
providing redundancy of records.
1.1.7 Software Overview
The central console contains all of the
operating software and all of the
databases required by the Security
Escort System. The Security Escort
System Operations Manual describes that
portion of the system software, which
affects system operators (in most
cases, the Security Department
personnel). This Technical Manual
discusses only the software functions
that are specific to installation and
maintenance of the system.
When a receiver or alert unit detects a
reportable event (alarm, test, tamper,
loss of AC power, and so on) it goes
into an Off Normal state. To quickly
locate any devices which might be in
the Off Normal state, global commands
(which are interpreted simultaneously
by all of its devices) are issued by
the transponder approximately ten times
per second. These global commands are
followed by commands to specific
devices to determine the nature of the
Off Normal condition and, in the case
of an alarm or test, to obtain the
Transmitter Identification Number,
Transmitter Battery Condition, and
Received Signal Strength. This
All operations on the central console
computers are password access
controlled. The Logout option on the
Main Menu bar produces a screen for
Passwords may have different authority
levels, assigned by installation
company personnel or the Security
Department’s key operator.
information is used by the central
console to identify the subscriber
transmitting the alarm (test) and to
determine the subscriber’s location.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 1.0 Security Escort
System Architecture
EN | 10
1.2.1 Alarm Sequence
Figure 1: Screen Box for Password
Transmitter
Entry
When a user of the Security Escort
System activates an alarm with the
transmitter, multiple identical packets
of digital data are transmitted from
the hand-held transmitter to nearby
receivers. Each packet contains a
unique device identification code, an
alarm type indication, the transmitter
battery condition, and a check
Operations not accessible at a given
authority level appear in gray rather
than black on the central console. The
installation and maintenance portion of
the Security Escort Software is
sequence. Multiple packets are employed
to assure successful receipt of the
message by the receivers.
Receiver
designed to facilitate set-up and
modification of the system and to
provide rapid diagnosis of system
problems, usually with only one person
being required. From the central
console, simple commands can be used to
scan all devices on a particular
transponder for their current status.
Devices can be enabled or disabled from
the central console and the on-board
transmitter of one receiver can be
activated to test an adjacent receiver
in order to confirm that its radio
receiver section is operating properly
(buddy check).
The receiver is continuously listening
for radio signals that might be alarm
or test data from transmitters. If the
incoming message is determined to be
valid, representing either an alarm or
a test from a transmitter, the peak
amplitude of the received signal is
recorded.
Transponder Scanning
The transponder continually scans all
of its receivers to see if any of them
received a valid transmission. Once a
transponder determines that one or more
of its receivers received a
transmission, it directs a message to
those receivers, to determine the
specifics of the transmission.
The Security Escort Software also
continually monitors the status of each
transponder to insure it is functioning
correctly. All communications between
the central console and a transponder
require acknowledgments to verify
message integrity. Each transponder
must transmit a message periodically,
to assure the central console that the
transponder is still operating
properly. Should a transponder fail to
transmit either a routine status report
or any other message to the central
console, the central console sends a
query to the transponder requesting a
message be returned. If there is no
response after six attempts at
Receiver’s Response
The receivers respond to these messages
with the identification code of the
transmitter that sent the alarm or
test, the alarm or test type, and the
amplitude of the signal received from
the transmitter.
Transponder Data Collection and
Response
The transponder next constructs a
message for the central console
containing the receiver addresses, for
all receivers responding to the event
and signal levels of the receptions,
the alarm or test type and the
transmitter identification number. The
transponder then verifies that the
communications channel is free and
transmits the information to the
central console. If the communication
channel is busy, the transponder delays
a random period of time and tries
again.
communications, a pop-up alert appears
on the central console.
1.2 System Operation
The following sections describe the
basic operation of the Security Escort
System during alarm, test, and various
other routine and emergency situations.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 1.0 Security Escort
System Architecture
EN | 11
Central Console Response
During Alarm
After acknowledging the alarm
transmission from the first
transponder, the central console begins
its alarm analysis while collecting the
alarm data from all other transponders,
which had receivers that detected the
alarm. The Subscriber Database is
checked to determine the appropriate
reaction to the alarm. If the
transmitter is assigned to a valid
subscriber and it is not designated as
a security or watchman device, the
central console commands the
transponders to turn on the appropriate
alert units. Depending on the settings
selected in the Security Preferences
Screen, this enables only the strobe
portion of the alert unit, or both the
strobe and siren. If the transmitter is
unassigned, or has been disabled by
selection of that option in the
Subscriber Database, no commands will
be issued to activate the alert units.
Note:
An option in the Security
Preferences Screen allows
unauthorized transmitters (not
programmed in the database) to be
treated like authorized
transmitters. For example, strobes
and/or sirens can be activated in
the case of an alarm transmission
(if they are also set to be
activated for authorized
The central console also writes the
time, location, and identity
information to the hardcopy printer and
writes a complete record of all
activities to the hard disks on both
the primary and backup computers.
Operator’s Response
The operator reacts to the alarm by
acknowledging the event with a
keystroke or click of the mouse, which
silences the alert sound from the
central console. This silences only the
central console enunciator, not the
outdoor sirens or interior horns. The
operator then directs response
personnel to the scene and awaits their
indication that the problem was
resolved.
transmitters).
The central console computes the
location of the transmitter by
comparing the signal strengths measured
by the receivers which detected the
transmission.
A partial map of the protected area is
displayed on the central console,
centered on the computed location, and,
a yellow circle is drawn to assist the
operator in guiding the response
personnel to the probable source of the
transmission. Other data drawn from the
Subscriber Database is added to the
central console display to assist in
the response to the alarm. In addition,
the central console enunciator is
activated to alert the operator to the
event.
When the response personnel advise the
operator that the problem is under
control, the operator enters his
password into a box on the central
console. This step causes the central
console to send commands to the
transponders to silence the sirens and
horns and extinguish the strobes and
LED’s. A reset of the system is
accomplished with another key stroke or
a mouse click on the Reset button on
the screen.
Figure 2: Central Console Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 1.0 Security Escort
System Architecture
EN | 12
Multiple Alarms
the database, but disabled, do not
receive a flashing green light or
flashing strobe that would indicate a
successful test.
Receivers can handle multiple separate
alarm or test events at the same time.
If the receiver’s event buffer is full
but contains test events, it discards
the test records in favor of an
incoming alarm. Similarly, the
transponder event buffer can hold
multiple events and it also replaces
test events with alarm events when its
buffer is full.
Central Console Response
The central console responds to the
report of a test from a transmitter by
collecting the data from each
transponder reporting the event, and
recording the locations of the
receivers that detected the
To assure that simultaneous alarms are
detected, the multiple identical
packets sent by the transmitters are
randomly spaced over approximately one
second. Only one of the packets must be
detected to produce an alarm. Thus a
collision between the transmissions of
two or more transmitters is virtually
eliminated. In addition, unless the
transmitters are in the same location,
they detect different groups of
transmission. In this case, however, it
does not calculate a location estimate.
It simply records the data on the
primary and backup computers’ hard
disks, prints the identity of the
subscriber, date and time on the
hardcopy printout, and displays generic
test icons on the central console in
positions corresponding to the
locations of receivers hearing the
transmission.
receivers. The central console is
capable of processing 30 concurrent
alarms. When there is more than one
active alarm, the central console
displays data for the first to be
received and also indicates the total
number received and the identity of the
individuals transmitting them. The
operator can click on the name of an
individual to see the data for a
particular alarm.
In the case of test transmissions from
Security Transmitters or Watchman
Transmitters, the central console
determines the closest receiver to the
transmission and creates a guard tour
event which becomes a part of the Guard
Tour Report.
Figure 3: Console Screen Showing
test Icons
1.2.2 Test Sequence
Transmitter
When the user of the Security Escort
System activates a test transmission,
multiple identical packets of digital
data are transmitted. In this case, the
digital data in the transmitted packets
contain a test code rather than an
alarm code.
Receiver
The receiver responds to a test
transmission the same as to an alarm
transmission by decoding the radio
signals, and measuring signal levels.
Transponder Data Collection and
Response
The transponder collects data on a test
event in the same manner as for an
alarm event, it does not command the
LED (green for test confirmation) to
flash until it has been commanded to do
so by the central console. Transmitters
not in the Subscriber Database, or in
Operator’s Response
There is no response required of the
operator in the case of a test
transmission.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 2.0 Setting Up The
System
EN | 13
If this computer runs other programs
at the same time, Security Escort is
running, set the Not Always Top
2.0 Setting Up The System
2.1 Initial System Configuration
The default password is PPP. The
default password, the Master password,
and passwords for all system operators
added by referring to the Operators
Database in the Security Escort
To program the ID Receiver to
automatically enter the transmitter
Operations Manual should be changed.
To generate the map file for the
screen display, refer to Section 5.1
To set the names of the subscriber
classes, see System Default Screen
in the Security Escort Operations
Manual.
To setup the transponder COMM ports
refer to the Section 3.3.18
To program the transmitters into the
Subscriber Database, refer to the
Security Escort Operations Manual.
To setup the system COMM ports refer
3.0 System Menus and
Screens
To set the function of the system
COMM ports and setup remote access,
3.1 File Menu
Figure 4: File Menu
To program the system configuration,
To program the system responses to
To program the system responses to
After communications to the
transponders are established for any
transponder that uses a Proxim Radio
to communicate, program the Uses
Proxim Radio field in the
Transponder Parameter Change Screen.
If all alarms are to be silent,
program the Run Silent field. (See
3.1.1 Locate Transmitters
This selection allows the operator to
display the last reported location of
the transmitter assigned to the
indicated individual or asset. When the
individual or asset is selected from
the list, the time of the last
supervision report is shown (or None is
displayed if no supervision report was
received from that transmitter). On the
map, the last report location is shown.
If this system has master and slave
computers, set the Default Master
Computer and Default Slave Computer.
If using pager access in this
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 14
Signal Levels Shown in Icons"
Figure 5: Locate Transmitters
3.1.2 Maintenance Alarm Database
3.1.3 Operator Database
Maintenance Transmitters, when
activated in the Test or Alarm Mode,
generate a series of multiple data
packets like Subscriber Transmitters,
however, a special code in each packet
identifies the transmitter as a
Maintenance Transmitter.
The Operator Database contains the
information on the individuals who are
authorized to operate the system, their
authority levels, and passwords. See
the Security Escort Operations Manual.
3.1.4 Reports Database
The receiver responds to a maintenance
alarm or test transmission in the same
way it responds to a subscriber alarm
or test, unless the receiver is put in
the Setup Mode. The transponder then
reports the Maintenance Transmitter
identification number and all signal
levels to the central console which
creates the location estimate and
processes the data as it would for a
normal alarm.
The Reports Database contains the
information on alarms that were
previously processed by the system.
Alarm data and maps showing the
operators view can be recalled. See the
Security Escort Operations Manual.
3.1.5 Subscriber Database
The Subscriber Database contains the
information on the transmitters that
are assigned in the system. See the
Security Escort Operations Manual. When
the Advanced button is pressed in the
Subscriber Database Edit Screen, the
Edit Subscriber’s Advanced Features
Note:
All Maintenance Transmitters are
assumed to be valid so there is no
need for the central console to
check for the identification number
in the Subscriber Database.
The Edit Subscriber’s Advanced Features
Screen is used to set up special
transmitters that monitor fixed
locations, subscriber pager access,
parameters for point transmitters, the
virtual fence for a wandering alarm,
the alarm group for arming of the
transmitter, and check-in requirements
for this transmitter.
The central console does not generate
an audible alert for the operator and
does not create an alarm display on the
main central console. Because they can
be set to graphically display received
signal levels, maintenance alarms are
very useful in verifying that the
system coverage exists at any location
in the protected area and that receiver
redundancy is adequate.
Figure 7: Edit Subscriber’s
Advanced Features Screen
Figure 6: Maintenance alarm with
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 15
Fixed Location Transmitter
This section is used only when this
transmitter is mounted in a fixed
location (it does not move). When this
transmitter transmits an alarm, it is
always reported at the programmed
location.
Floor Level
This is the floor level where this
alarm is located for a fixed location
transmitter.
Map X Position
This is the X coordinate of the map
position where this alarm is located
for a fixed location transmitter.
Map Y Position
This is the Y coordinate of the map
position where this alarm is located
for a fixed location transmitter.
Locate
Phone Number
When clicked, the Edit Subscriber’s
Advanced Features Screen disappears and
the cursor changes to a cross hair.
Moving the cursor to a point on the map
and clicking the left mouse button
scrolls the map to that point at the
center of the screen.
This phone number is dialed to send a
pager message to this subscriber.
Typically, this is a different phone
number than the one that is manually
dialed to access this pager. The phone
number is assigned by the paging
service.
When the map is showing the desired
alarm location, move the cross hair to
the exact location of the alarm to be
reported and click the right mouse
button. The Edit Subscriber’s Advanced
Features Screen reappears and the
selected location is entered into the X
and Y coordinates.
Pager Password
This is the password to be sent to the
paging service when a page is sent to
this subscriber. Leave blank if not
required (typically the pager password
is not required). The pager password is
assigned by the paging service.
If while the cross hair cursor is
displayed, you want to exit without
changing any coordinate values, press
the [ESC] key and the Edit Subscriber’s
Advanced Features Screen reappears.
Pager ID
This is the ID that identifies the
pager to receive the pager message
(many times this value is the last
seven digits that are manually dialed
to access this pager). The pager ID is
assigned by the paging service.
Map Number
Defines which bitmap is displayed for
the fixed location of this transmitter.
The default map is zero, which
corresponds to bitmap MAP0.EDB stored
in the Escort sub-directory. Map 1
would be MAP1.EDB. There can be 100
maps per Security Escort System (0 to
99).
Pager Group
These are the pager groups that this
subscriber is a member of. This
subscriber can be a member of up to
three different pager groups.
Pager Confirmation Not Required
If checked, the confirmation pager
message is not sent to this pager if
alarm is acknowledged by an
acknowledgement transmitter.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 16
Enable Reed Switch
Disable Open Loop
If checked, the reed switch input of
this transmitter is enabled and causes
an alarm. Otherwise, the reed switch
If selected, an open loop on this
transmitter does not cause an Alarm or
Trouble Report to display. To enable
input is disabled. The alarm group this this option, the transmitter’s class
transmitter is assigned to must be
armed, for this input to cause an
alarm, which is displayed. If no alarm
group is assigned, the transmitter is
always armed. To enable this option,
the transmitter’s class must be set to
point type.
must be set to point type.
Alarm on Open Loop
If selected and the alarm group this
transmitter is assigned to is armed, an
open loop on this transmitter causes an
Alarm Report to display. The alarm
group this transmitter is assigned to
must be armed for this input to cause
Optional Text
This is optional text that can be added an alarm, which is displayed. If no
to the location text when this input
reports an alarm. To enable this
option, the transmitter’s class must be this option, the transmitter’s class
set to point type.
alarm group is assigned, the
transmitter is always armed. To enable
must be set to point type.
Disable Shorted Loop
Trouble on Open Loop
If selected, a shorted loop on this
transmitter does not cause an alarm or
trouble report to display. To enable
this option, the transmitter’s class
must be set to point type.
If selected, an open loop on this
transmitter causes a Trouble Report to
display. To enable this option, the
transmitter’s class must be set to
point type.
Alarm on Shorted Loop
Alarm When Armed, Trouble When Disarmed
on Open Loop
If selected and the alarm group this
transmitter is assigned to is armed, a
shorted loop on this transmitter causes
an Alarm Report to display. For this
input to cause an alarm, the alarm
group this transmitter is assigned to
must be armed, which is displayed. If
no alarm group is assigned, the
If selected and the alarm group this
transmitter is assigned to is armed, an
open loop on this transmitter causes an
Alarm Report to display. If selected
and the alarm group this transmitter is
assigned to is disarmed, an open loop
on this transmitter causes a Trouble
Report to display. If no alarm group is
assigned, the transmitter is always
armed. To enable this option, the
transmitter’s class must be set to
point type.
transmitter is always armed. To enable
this option, the transmitter’s class
must be set to point type.
Trouble on Shorted Loop
If selected, a shorted loop on this
transmitter causes a Trouble Report to
display. To enable this option, the
transmitter’s class must be set to
point type.
Fixed Location and Pager Text
This is the text that displays as the
location of the alarm for fixed
location transmitters and on pagers
reporting this alarm.
Alarm When Armed, Trouble When Disarmed
on Shorted Loop
Transponder Name
If selected and the alarm group this
transmitter is assigned to is armed, a
Select the transponder with the area
that defines the area for a wandering
shorted loop on this transmitter causes (virtual fence) alarm. Refer to
an Alarm Report to display. If selected Transponder Area for the operation and
and the alarm group this transmitter is setup of the wandering alarm (virtual
assigned to is disarmed, then a shorted fence alarm).
loop on this transmitter causes a
Trouble Report to display. If no alarm
group is assigned, the transmitter is
always armed. To enable this option,
the transmitter’s class must be set to
point type.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 17
Transponder Area
Requires Check-in
When this checkbox is checked, this
Wandering Alarm - Create a protected
area by placing a virtual monitor fence transmitter activates once each day
around an area of the main map. These
areas are defined in the transponder
database. If this transmitter is
constrained to remain within one of
these defined areas, first select the
defining transponder in the Transponder
Name field. Then select the desired
area from this dropdown list of the
transponder’s area names.
during the check-in schedule time. At
the end of the check-in period, if the
subscriber fails to check-in, a Failed
to Check-in Report is generated and
presented to the operator. This report
contains all of the people who failed
to check-in with their first address
line and phone number. All subscribers
in the report must be checked on to
make sure they are not in need of
assistance, as this may be a life-
threatening situation. A printed report
may be generated.
For the wandering alarm to work, the
supervision period must also be
programmed for this transmitter.
Specific transmitters are marked in the
Subscriber Database to be constrained
within a specific fenced area defined
by this option. If the transmitters
leave their defined area, the system
reports this as a wandering alarm and
continues to monitor and track the
location of the transmitter until the
alarm is canceled from the screen in
the normal way. However, these tracking
updates can only occur every
If the transmitter is not a point type,
the transmitter can generate alarms and
therefore a test transmission is used
for the check-in.
If the transmitter is a point type, any
non-trouble transmission serves as a
check-in.
One of the ten schedules must be
selected as the check-in schedule to
define the check-in period.
supervision transmission period (not on
an accelerated rate like a tracking
alarm).
Done
Click this button when all changes are
complete to return the main Subscriber
Database Edit Screen.
The Security Escort System computes the
location of the transmitters when they
broadcast automatic supervision
transmissions periodically.
3.1.6 Transponder Database
The Transponder Database is established
at system set-up and contains all
necessary configuration data for each
transponder, receiver, and alert unit.
It describes the basic structure of the
installation, including all device
names, locations, types, multiplex
addresses, and so on. This information
is used by the central console to
generate alarm and test displays on the
central console and in determining
which alert units are activated.
Because of the basic location accuracy
and the floor-to-floor accuracy of the
system, there is a potential for some
false alarms. If false alarms are a
problem, check the Filter Virtual Fence
checkbox in the Edit Security
Preferences Screen. If you do this, two
successive location calculations
indicate the transmitter moved outside
the protected area before an alarm was
generated. The downside of this is a
delay in the reporting of a wandering
alarm of one extra transmitter
supervision period.
Alarm Group
This is the alarm group that controls
the arm/disarm status of this
transmitter. Select the desired alarm
group from the dropdown list. This
alarm group must be armed for this
transmitter to cause an alarm, which is
displayed. If no alarm group is
assigned, the transmitter is always
armed.
Figure 8: Find Transponder’s
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 18
Zero is not allowed as a transponder
address.
Database Record
Comm Port Index
This indicates which central console
communications port to use to
communicate with this transponder. The
Transponder Comm Port Setup Screen
selects the specific physical port that
this index refers.
Radio ID
This is the identification number for
the radio interface unit, if the
transponder communicates to the central
console by a radio link. (This feature
is currently not implemented.)
Access the Transponder Database from
the File Menu on the Main Menu bar. The
following paragraphs describe the
elements of the Find Transponder’s
Database Record Screen.
Isolate From All Other Transponders For
Location
When checked, this transponder is
isolated from all other transponders
for location considerations. This is
used when distant transponders
sometimes hear an alarm and throw off
the alarm location calculation. If this
checkbox is checked, it indicates that
this transponder is protecting an area
that is independent of all other
transponders in the system. When an
alarm is reported and receivers on this
transponder have the best reception,
only the receivers on this transponder
are considered for the location of this
alarm. If another transponder has the
best reception, then the receivers on
this transponder are ignored for the
location of this alarm.
Transponder
This box contains the names of the
transponders. Clicking the arrow to the
right of this box displays a drop-down
list. The names of each transponder in
the system display, allowing easy
selection for review or editing.
The transponder names are assigned
during set-up and used to indicate the
physical location of the transponder or
the region of the protected area
covered by a particular transponder.
Created, Modified, Modify Oper
The system software automatically
creates these three fields to the right
of the Find Transponder’s Database
Record Screen. They represent the date
the transponder was first entered into
the Transponder Database, the date of
the last change of any entry for this
transponder, and the identity of the
operator who made the last change
(determined from the password entered
to make the change).
Ignore Communications Failure
This checkbox allows communications
failures to be ignored for this
transponder. It is used during a new
installation for transponders that are
not yet fully on line. During system
maintenance when a transponder is out
of service for a while, it is used so
that the communications failure
messages do not flash on the screen and
distract the operator. Checking this
checkbox causes the system to ignore
communication failure. Therefore, if
communications fail with this
transponder, the area this transponder
protects is not protected and alarms
from subscribers in that area are
missed without the operator’s
Transponder ID
This is a number assigned to the
transponder at system set-up. It is
used by the central console to identify
the transponder during all
communications between the central
console and the transponder. The number
must agree with the transponder
address, which is set during final
installation by switches on the
transponder circuit board.
knowledge. This checkbox should not be
checked in a live system.
Note:
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 19
Insert New
Next
Clicking this button displays a new
Edit Subscriber’s Advanced Features
Screen. This is used to enter a new
transponder to the database.
Clicking this button changes the
displayed transponder to the next
transponder in the database.
End of File
Edit Data
Clicking this button changes the
displayed transponder to the last
transponder in the database.
Clicking this button allows the
currently displayed transponder’s
database record to be edited.
Mux Point Data
Kill Transponder
The lower portion of the Find
Clicking this button deletes the
displayed transponder’s database
record. If the transponder is deleted.
its data is permanently deleted and
cannot be recovered.
Transponder’s Database Screen provides
information on each of the devices
controlled by the transponder selected
in the Transponder field. Two digits
represent each receiver or alert unit
address; the first is the number of the
multiplex bus on which the device is
mounted (0 to 7) and the second is the
multiplex point address assigned to the
particular device. On each of the eight
multiplex busses up to eight devices
may be installed, but each device must
be assigned a unique multiplex point
address (0 to 7). More than one device
can have a particular multiplex point
address, but only if on different
busses. The multiplex point addresses
are assigned by switch settings on the
device (receiver or alert unit) circuit
boards. These multiplex point address
settings are also a part of the
Transponder Database. The multiplex
address shown in the Transponder
Delete Point
Clicking this button deletes the
displayed point only from the displayed
transponder’s database record. If the
point is deleted, its data is
permanently deleted and cannot be
recovered.
Copy
Clicking this button copies the
displayed transponder’s database record
into a new transponder record. This
allows similarly configured
transponders to be programmed once,
then copied into a new record.
Note:
It is not possible to edit the
transponder ID itself. If this
should be necessary, the Copy button
can be used to produce another
Transponder Database entry
Database and the multiplex address set
on the device circuit board must agree.
The Transponder Setup Screen s used to
verify multiplex address settings.
duplicating the first, but with the
transponder ID blank. The new
transponder ID can be entered, the
new data saved by using the Save
button, and the old transponder
entry can be deleted by using the
Kill Transponder button.
It is a good idea to create an
entry in the Transponder
Database for each transponder
in the system before entering
the data for each device so
that all transponders appear in
the drop-down menus.
3.1.7 Creating a New Transponder Entry
Print
The creation and modification of the
Transponder Database requires special
authority levels usually assigned only
to installation company personnel.
Clicking this button prints the
displayed transponder’s database
record.
Beginning
The Insert New button creates a new
Transponder Database Screen, ready for
entry of data.
Clicking this button changes the
displayed transponder to the first
transponder in the database.
Previous
Clicking this button changes the
displayed transponder to the previous
transponder in the database.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 20
The System Design Layout Sheets
prepared in advance by the installation
manager should contain the necessary
information for assigning the
transponder name and ID, the comm port
or radio ID, as well as the names and
multiplex addresses for all receivers
and alert units connected to each
transponder.
Show Areas
If selected, the lower half of the
Transponder Database’s Screen shows the
area’s database values.
Area Number
Each Transponder can have up to 80
areas defined (prior to version 2.04 of
the software only 40 areas could be
defined). Area numbers range from 0 to
79. Use the Locate button to define the
area graphically on the map.
The System Design Layout Sheets also
contain the text used to indicate the
receiver locations and designates the
alert units driven by each receiver.
Point Number
Each receiver and alert unit connected
to the transponder has a unique point
number assigned during the system
design process. This number corresponds
to a specific bus number and point
multiplex address number. The multiplex
address, set by means of switches on
the device (receiver or alert unit)
itself, must correspond with the point
number assigned in the Transponder
Database. For instance, a device
programmed with multiplex address
location 3 and on bus 5 is point number
29. This relationship is displayed in
the table that displays anytime a ? box
is clicked with the mouse. Clicking on
any number in the table automatically
enters that number into the Point
Number field on the Transponder
Figure 9: Blank Screen Resulting
from Selecting the Insert New
Button
Database Screen and closes the table
screen.
3.1.8 Setting Receiver Parameters
If the Transponder Database already
contains the transponder, the Edit
button is used to allow completion or
modification of the data.
Trouble Type Text
This is the text that is shown in the
Trouble Screen when the remote key
input on the transponder goes active
(shorted).
Trouble Tamper Text
This is the text that is shown in the
Trouble Screen when the remote key
input on the transponder goes into
trouble (open).
Trouble Response Text
This is the text that is shown in the
Trouble Screen as the response test.
The actions the responding individual
should take.
Figure 10: Select Point Screen with
"All Points" Selected
Show Points
If selected, the lower half of the
Transponder Database’s Screen shows the
point’s (receiver, virtual receiver, or
alert unit’s) database values.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 21
A third number, the point number is
+, -, Bus + and Bus -
unique to a particular device. Point
numbers range from 0 to 63. There is a
one-to-one correspondence between a
point number and a point multiplex
address/bus number pair. The point
number assignment is presented in a
table displayed whenever the ? box to
the right of the Point Number field is
clicked.
These buttons, just below the Point
Number field, allow you to quickly
advance the device selection by one
location, either one point location (+
or -) or one bus number (Bus + or Bus -
). This is useful when a task requires
proceeding from device to device, as
during system setup or check out. The ?
box is used to display all devices to
facilitate quick selection of a
Figure 11 illustrates a quick way to
select a particular device without
having to translate between the two
numbering systems. Three buttons at the
bottom of this screen allow the user to
display all possible device numbers
(whether or not the particular
transponder has a device assigned to
the number) or, to display only
locations populated by receivers or
only locations populated by alert
units.
particular device. It is most useful
when diagnosing a problem with a
particular device.
Point Type
The Point Type field indicates the type
of device (receiver, virtual receiver,
or alert unit) located at the location
currently selected in the Point Number
field. Once the Point Number field
contains the proper value, the device
type is set by selecting from the
options in the drop-down menu that
appears when the arrow to the right of
the Point Type field is clicked.
When the Point Number button in the
table is clicked, the Point Number
table disappears and that point number
automatically appears in the Point
Number field of the Transponder
Database Screen. The bus number and
point address are also changed to
reflect the selection
Figure 11: Select Point Screen with
"Receivers Only" Selected
Figure 12: Drop-Down Menu for
Selection of Point Type
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 22
Use the receiver selection when there
is a physical receiver connected at
this bus location.
The virtual receiver is intended to
compensate in cases where there is a
receiver imbalance. For example, if a
building with a dense population of
receivers is adjacent to a fence with
few receivers and an alarm occurs
between them, the alarm location can
pull towards the building. The virtual
receiver references two other physical
receivers that must be on the same
transponder. Only if both of the
referenced receivers receive an alarm
transmission, is the virtual receiver
added to the alarm as if a physical
receiver heard the alarm at the average
receive level of the two referenced
receivers. The virtual receiver’s
location and sensitivity can be
Figure 13: Data Entry After
Selection of Receiver Point
Type
Use the alert unit selection when there
is an alert unit connected at this bus
location.
adjusted the same as a physical
Figure 14: Data Entry after
Selection of Alert Unit Point
Type
receiver. After a virtual receiver is
added, verify the surrounding areas to
make sure they were not adversely
affected. In no event, should a virtual
receiver be utilized as a cost savings
measure to avoid the installation of an
actual receiver.
Figure 16: Data Entry when Show
Areas is Selected
Use the virtual selection when there is
no physical device connected at this
bus location. Starting with version
2.03 of the Security Escort software,
you can add virtual receivers in the
Transponder Database. A virtual
receiver is added at one of the 64
points allowed per transponder.
However, there is no physical hardware
used.
Figure 15: Data Entry after
Selection of Virtual Receiver
Point Type
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 23
Alert 1, Alert 2, Alert 3, and Test
Selection
Each receiver can be assigned up to
three alert units that are activated if
it is one of the receivers reported by
the transponder as part of an alarm
event. Each receiver can also be
assigned one alert unit that is
activated to confirm test
transmissions. These alert units do not
need to be connected to the same
transponder as the receiver. The
Transponder field contains the
transponder to which the designated
alert unit is connected and the Point
field contains the point number of the
alert unit on that transponder.
Changing the algorithm setting for a
receiver only affects the location when
the alarm is close to this receiver and
it hears the alarm the strongest. The
stronger the pull the more the alarm is
pulled towards the receiver, with
linear having no extra pull.
The test boxes similarly designate the
alert unit, if any, whose strobe unit
is activated in the event of a test
transmission from a transmitter.
The algorithm setting is only available
if the Enable algorithm tweaks field is
checked in the System Preferences
Screen. Also Security Escort Software
version 2.03 and higher, allows
individual receiver sensitivity to be
set in the Transponder Database.
Receivers can be adjusted from 50% to
149% of their normal sensitivity using
the SA% field.
To assign alert units to each receiver,
use the drop-down menus to the right of
the boxes labeled Alert 1, Alert 2, and
Alert 3 to select the transponder of
the designated alert unit. Type point
number into the Point field.
Floor Level
Figure 17: Drop-Down Menu for
Assigning Alert Units to
Receivers
This selects the physical floor level a
receiver is mounted at or a virtual
receiver acts like it is mounted at. It
is very important that this setting is
correct for the operation of the
location algorithm.
Figure 19: Receiver floor level
selection
Algorithm
Starting with version 2.03 of the
Security Escort Software, there are
five different location algorithms that
can be selected on an individual
receiver basis in the transponder
database. Classic (original Escort
algorithm), linear, low pull, medium
pull, and strong pull. By default, when
a receiver is set for outside or tunnel
it uses the linear algorithm; all other
receivers use the low pull algorithm.
The receiver that hears the alarm
transmission the strongest determines
the algorithm used for this alarm.
Receiver 1 and Receiver 2
These are the two receivers, on the
same transponder, that a virtual
receiver assumes the average of. Both
receivers must receive a signal before
the virtual receiver reports it also
received a signal that is the average
of the other two receivers signals. The
location algorithm and sensitivity
adjust work the same for a virtual
receiver as for a physical receiver.
Figure 18: Location Algorithm
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 24
The SA% option is only available if the
Enable algorithm tweaks field is
checked in the System Preferences
Screen. Also in the Transponder
Database the Algorithm dropdown list
allows selection of Default, Classic,
Linear, Low, Medium, or Strong pull
location algorithms for each
transmitter. The point reporting the
best reception level determines the
actual algorithm used for the location
on any event. If programmed for
Default, the algorithm used is Linear
for points programmed as outdoor or
tunnel. All other points use Low. If
the point reporting the best reception
level is not programmed for the Default
algorithm, the location calculation
uses the algorithm programmed.
Location
This block contains the text to be
displayed on the Alarm Screen if this
receiver is one of those closest to the
alarm source. The description is
developed with the guidance of the
security personnel who must respond to
an alarm. It is vital that the
description be clear and unambiguous to
them.
To enter a location description, place
the cursor in the Location field, click
the mouse, and begin typing. Receiver
and alert unit location names are
important because they are used for
directing response to an alarm and aid
service personnel in identifying the
device in the event of a problem. The
Problem Reports displayed on the
central console and printed by the
hardcopy printer contain the device
location descriptions that are entered
in the Location field.
Map
Defines which bitmap to display for
this receiver or area when an alarm is
closest to it. The default map is 0,
which corresponds to bitmap MAP0.EDB
stored in the Security Escort sub-
directory. Map 1 is MAP1.EDB. There can
be 100 maps per Security Escort System
(0 to 99).
SA%
Security Escort Software version 2.03
and higher allow individual receiver
sensitivity to be set in the
Transponder Database. Receivers can be
adjusted from 50% to 149% of their
normal sensitivity. No physical
receiver changes or upgrades are
required. This setting should only be
changed if there are known location
accuracy problems in the area of this
receiver. Settings of 50 to 99
desensitize the receiver to 50% to 99%
of the actual received signal strength.
Settings of 1 to 49 increase the
sensitivity to 101% to 149% of the
actual received signal strength. Try
changing the sensitivity of receivers
one at a time while testing the alarm
location response. For example, if
alarms are being pulled towards a
particular receiver, lower its
Video Switcher
Selects a system serial port programmed
in the Remote Setup Screen displaying
the most likely area the alarm is
located on the CCTV monitors near the
central console. The string activates a
macro in the video switcher that
selects the appropriate camera and
controls any required zoom and tilt
actions. Up to 40 characters can be
entered. Control characters can be
entered as [^][A] for control A.
Pager Group
The pager group that is paged if the
alarm location is determined to be in
this area.
sensitivity in 10% increments and
retest. If the area can be corrected
using this method, verify the
surrounding areas to make sure they
have not been adversely affected.
Generally, it is better if the
correction is done in small steps while
verifying the adjacent areas, rather
than trying to correct the entire error
in one step.
Floor
Determines the floor number that this
area is defined for. The areas on
floors above and below this one can be
defined differently. For an area to be
selected when an alarm is received, the
location determined by the central
console must be located within the
defined area and must be located on the
designated floor.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 25
If the area being defined is a virtual
monitor “fence” area for Wandering
Alarms, the monitor fence (area
boundary) should be drawn at least 7.62
m (25 ft.) past the area to be
protected to reduce potential false
alarms.
Virtual Fence Area
If this checkbox is checked, this area
is not used for a normal alarm area
location. This area is only used to
define a virtual fence. Specific
transmitters in the Subscriber Database
can reference this transponder and
area. When they reference this area and
the system locates the transmitter
position outside the area, a Wandering
(Virtual Fence) Alarm is generated.
This alerts the operator and shows the
position of the transmitter.
If the cross hair cursor is displayed
and you want to exit without changing
any coordinate values, press the [ESC]
key and the Edit Transponder’s Database
Record Screen reappears.
Cut
Locate
Clicking this button copies the
displayed point or area data to a
clipboard and returns all values to
their defaults.
When clicked, the Edit Transponder’s
Database Record Screen disappears and
the cursor changes to a cross hair.
Moving the cursor to a point on the map
and clicking the left mouse button
scrolls the map so the point is at the
center of the screen and all previously
defined receivers and areas are shown
with numerical labels.
Copy
Clicking this button copies the
displayed point or area data to a
clipboard. Displayed values are not
changed.
Paste
When the map is showing the location of
the desired receiver, move the cross
hair to the exact location of the
receiver and click the right mouse
button. The Edit Transponder’s Database
Record Screen reappears and the
selected location is entered into the X
and Y coordinates.
Clicking this button copies the
clipboard values to the displayed point
or area data. The values on the
clipboard are not changed and can be
copied to more points or areas.
Save
Clicking this button saves all changes
to the database.
When the map shows the desired
location, move the cross hair to the
exact location of the first point of
the polygon that describes the boundary
of the area and right click. Move the
cursor to the second point of the
polygon and again right click. The
computer draws a straight line between
the first and second points. Repeat
this process drawing all sides of the
polygon to define the area. To close
the polygon, place the last point on
top of the first point. The polygon can
have up to nineteen sides and no two
lines of the polygon may cross each
other. If you try to create more than
nineteen sides, the computer
Cancel
Clicking this button closes the screen.
displays giving you another chance to
save the changes by clicking the Yes
button.
Figure 20: Save Changes Screen Box
automatically closes the polygon with
the nineteenth side. When the polygon
is closed, it can be crosshatched to
make it more visible. After the polygon
is complete, double click the left
mouse button to return to the Edit
Transponder’s Database Record Screen.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 26
3
.1.9 Transmitter Change
Figure 22: Backup Screen
Refer to the Security Escort Operations
Manual.
3.1.10 Exit
Click this button to close the Security
Escort application. Enter your password
at the prompt to verify you have the
authority to shut down the program.
3.2 Utilities Menu
Figure 21: Utilities Menu
Operators
This is the database of all individuals
with passwords to operate the system
software and acknowledge alarms.
Subscriber
This database contains all the
transmitters assigned in the system.
Transponders
This database contains the
transponders, receivers, virtual
receivers, and alert units
configurations.
Reports
This database contains all the Alarm
Reports and related alarm map screens.
Master Database Drive
Store the backup files in the Security
Escort Master Database path. See the
System Directories and Network Address
Screen.
3.2.1 Backup Screen
Use this screen to make backups for all
the databases. Only the databases with
a checkmark are backed up. Preferably,
all databases should be backed up at
once. Only when they do not fit on one
floppy disk should you save individual
databases to one floppy; then switch
floppy disks and repeat the procedure
to save the rest of the files. As
insurance against database problems,
make multiple backups to different
disks frequently. Store at least one
backup copy in a different location
from this system and remember to keep
this copy current.
Slave Database Drive
Store the backup files in the Security
Escort Slave Database path. See the
System Directories and Network Address
Screen.
Local Database Drive
Store the backup files in the same sub-
directory on this computer where the
Security Escort System components are
stored (typically C:\ESCORT).
Cartridge Disk Drive
Store the backup files in the
Backup/restore to disk cartridge path
field assigned in the System
Preferences Screen. This path can point
to a cartridge disk drive, a local hard
disk, or a network disk drive.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 27
Floppy A
Master Database Drive
Store the backup files on the floppy
disk in floppy disk drive A.
Store the backup files in the Security
Escort Master Database directory. See
the System Directories and Network
Address Screen.
Backup
When the Backup button is clicked, all
the databases selected with a checkmark
are saved to the destination selected
on the right.
Slave Database Drive
Store the backup files in the Security
Escort Slave Database directory. See
the System Directories and Network
Address Screen.
3.2.2 Restore Screen
Use this screen to restore previously
made database backups to the system
databases. On the left, select the
database to be restored. The right
indicates where this database backup is
currently located. Click the Restore
button to replace the existing database
file with the backup. This process also
rebuilds the database and its index
tables which corrects most database
structure problems.
Local Database Drive
Store the backup files in the same sub-
directory where on this computer the
Security Escort System components are
stored (typically C:\ESCORT).
Cartridge Disk Drive
Store the backup files in the
Backup/restore to disk cartridge path
field assigned in the System
Preferences Screen. This path may point
to a cartridge disk drive, a local hard
disk, or a network disk drive.
Figure 23: Restore Screen
Floppy A
Store the backup files on the floppy
disk in floppy disk drive A.
Clear Entire File
If the database is selected and the
Restore button is clicked, the entire
database is cleared of all records.
This selection must be used with
extreme caution. Hold down the [SHIFT]
and [CTRL] keys when opening the screen
to enable the Clear Entire File option.
Restore
When the Restore button is clicked, the
database selected is restored from the
destination selected on the right.
This message box is a reminder that if
changes to the system databases were
made since the backup was made, the
changes are lost. Therefore those
changes must be redone to the restored
database.
Operators
The database of all individuals with
passwords to operate the system
software and acknowledge alarms.
Subscriber
This database contains all transmitters
assigned in the system.
Transponders
This database contains the
transponders, receivers, virtual
receivers, and alert units
configurations.
Reports
This database contains all the alarm
reports and related alarm map screens.
Figure 24: Restore Warning Message
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 28
Box
This message box indicates the restore
was completed. The previous database
file is renamed with an .OLD extension
and saved in the Security Escort sub-
directory. Only the most recent
database of each type is retained.
Turn On Alarm Strobes
Figure 25: Restore Save Old database
Message Box
Checking this option causes the strobe
lights on the alert units and
transponders to flash in the event of
an alarm.
Display Unauthorized Alarms
This checkbox determines if
unauthorized alarms are displayed on
the central console. Unauthorized
alarms are those triggered by
transmitters not currently registered
in the Subscriber Database. These could
be transmitters that were removed from
the database because they were lost or
stolen, transmitters not yet issued, or
transmitters issued to subscribers at
another Security Escort System.
Typically, this checkbox should not be
checked.
3.2.3 Security Preferences Screen
The Security Preferences Screen
controls those aspects of the Security
Escort System operation that are
determined by the security director.
Sound Unauthorized Alarms
Turn On Outside Sounders
This checkbox determines if
This checkbox is used to activate or
deactivate the sirens on alert units
and transponders. Some security
directors prefer that all alarms be
silent, others choose to employ sirens.
Checking this option causes the sirens
on the alert units to sound in the
event of an alarm. Temporarily
unauthorized alarms are to be sounded
on the horns of the receivers and the
sirens of the alert units and
transponders. The option is not
available unless the Display
Unauthorized Alarms field is selected.
Typically, this checkbox should not be
checked.
deactivating the sounders is necessary
during maintenance.
Filter Virtual Fence
If the virtual fence option is used,
check this box to reduce the number of
the false alarms generated. If the box
is checked, the actual alarms are
delayed by the supervision period of
the transmitter.
Figure 26: Security Preferences
Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 29
No Point Text If Area Text
Installer Alarms Silent
This checkbox affects the location text If this checkbox is checked, alarms
shown on the Alarm Screen. If this
checkbox is checked and the alarm is
determined to be within a predefined
area, only the area text is displayed
(any receiver location text is
suppressed). Typically, this checkbox
should be checked.
transmitted by transmitters issued to
installation company representatives
and visitors are to be silent. The
operator at the central console is
alerted, but the sirens of the alert
units or the horns in the receivers are
not sounded. Typically, this checkbox
is checked.
Output includes Subscriber ID
Alarm Voice Output
If this checkbox is checked, any time
the system prints or displays text for
an alarm or test the subscriber’s ID
number is displayed. Otherwise, the
subscriber’s ID is not shown.
If this checkbox is checked, predefined
sound (.WAV) files can be played at the
alarm console for specific alarm types.
Typically, this checkbox is not
checked.
Output includes Transmitter ID
Show Personal Data
If this checkbox is checked, any time
the system prints or displays text for
an alarm or test the transmitter ID
number is displayed. Otherwise, the
transmitter ID is not shown. Typically,
this checkbox would not be checked.
If this checkbox is checked, personal
height, build, hair, and eye color data
displays on the alarm screen.
No Receiver Icons
If this checkbox is checked, individual
receiver icons are not shown on the
alarm map display. Typically, this
checkbox is checked.
Limit Alarms to 1 Transponder
This box should not be checked. It is
used only in a system where all
transponders operate on areas separate
from each other. It prevents all
interactions between receivers on
different transponders. Typically this
is undesirable and there is now a
selection on an individual transponder
basis to accomplish this feature.
Show Tests On The Map
If this checkbox is checked, tests from
Subscriber’s Transmitter appear on the
normal map screen as OK or FAIL icons.
This signifies a successful test by a
valid subscriber or an attempted test
transmission from a transmitter not in
the Subscriber Database. This option
does not affect the display the
Option 2
This checkbox is for a future option
and at this time it has no function.
Leave this checkbox unchecked.
subscriber receives from a receiver or
alert unit’s strobe. Typically, this
checkbox is checked.
Require Alarm Report
All Pager Confm Not Reqd
If this checkbox is checked, the
operator is prompted to complete an
Alarm Report when the alarm is reset
from the screen. If the responding
officer is required to complete the
report or if no system report is
desired, this box should not be
checked. If the operator should
complete the report, check this box.
If checked, the confirmation pager
message is not sent to any of the pager
if the alarm is acknowledged by an
acknowledgement transmitter.
Option 4
This checkbox is for a future option
and at this time has no function. Leave
this checkbox unchecked.
Security Alarms Silent
Option 5
If this checkbox is checked, alarms
transmitted by Security or Watchman
Transmitters are to be silent. This
alerts the operator at the central
console, but does not sound the sirens
of the alert units or the horns in the
receivers.
This checkbox is for a future option
and at this time has no function. Leave
this checkbox unchecked.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 30
End Of Shift Reminder
Auto Silence Alarm In X Seconds
A check in this box causes a prompt to
appear on the central console each 5
min. for 30 min. prior to the end of
each shift if there are Incident
Reports that were not yet completed.
Responding officers should complete
Alarm Reports before the end of their
shift.
This box determines the length of time
that the sirens and horns sound before
being automatically silenced by the
central console. When the sounders are
automatically silenced in this way, the
central console remains in its Alarm
Mode. The numerical value is in seconds
and it can be set between 0 and 9999.
Typically, this value is set to prevent
violating local noise ordinances. It
defaults to 240 seconds (4 minutes.).
First, Second, Third Shift Reminder
The entries in these fields are the
times (24-hr. clock) at which the
central console prompts the operator
that one or more Incident Reports have
not been completed. Prompts are given
only if the End of Shift Reminder field
is selected.
Recall Operator In X Seconds
This box determines the length of time
before a recall alert is issued to the
operator at the central console when an
alarm displays. If neither the mouse
nor any key was actuated for the
Database Find Level
specified length of time, the central
console resounds the alarm sound once.
This feature prevents inadvertently
ignoring an active alarm event. The
numerical value is in seconds that can
be set between 0 and 240. Typically
this would be set to 60 seconds.
This is the minimum receive level (1 to
255) that must be heard before the
system automatically enters the
transmitter in the Subscriber Locate
Screen. It determines the distance the
subscriber’s transmitter must be within
the specified ID capture receiver (set
in the System Preferences Screen)
before the system recognizes the test.
On Outside Tests Flash Strobe For X
Seconds
The entry in this box controls the
approximate length of time the strobe
on an alert unit flashes to signify a
successful transmitter test. The value
is in seconds, and can be set between 0
and 15. Typically, it is set to 5
seconds.
Locate Test Level
This is the minimum receive level (1 to
255) that must be heard before the
system accepts a test generated by a
transmitter other than a guard, to be
printed with a location. It determines
the distance the transmitter must be
from a receiver before the system
recognizes the test and prints the
location. If the transmitter is too far
away from the receiver, that receiver’s
green light does not display, and the
guard knows to move closer to the
receiver for the test to register.
Man Down Delay Timer X Seconds
This value controls the time that a
transmitter must be in a man down
condition before a man down alarm
displays. Typically, it is set to 10
seconds. Setting this value too short
causes inadvertent man down alarms to
be generated.
Guard Tour Level
Man down jitter timer ‘X’ Seconds
This is the minimum receive level (1 to
255) that must be heard before the
system accepts a test generated by the
guard’s transmitter to be entered as a
location in the Guard Tour Report. It
determines the distance the guard’s
transmitter must be from a receiver
before the system recognizes the test
and creates the guard tour entry. If
the guard is too far away from the
receiver, that receiver’s green light
does not display and the guard knows to
move closer to the receiver for the
test to register.
This value controls the time that a
transmitter will not be considering any
man down alarm if man down alarm is
received immediately after restore and
before jitter time expire. This setting
will not be used in normal system.
Auto Reset Comm Ports ‘X’ Hours
This value controls the time that all
the comm ports in the system will be
automatically reset after configured
duration. This setting is used only if
any communication failure is observed
and should not be used unnecessarily.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 31
Guard Tour Minutes
3.2.5 System Labels Screen
This setting controls the time spacing,
in minutes, for entries of the guard’s
current location in the automatically
generated Guard Tour Report. If set to
15 min., an entry is generated each 15
min. the guard’s transmitter is within
range of the system.
The alarm type definitions are modified
to the customer’s requirements in
Figure 28: System Labels Screen
Pop-up Trouble Box Contact Information”
Each yellow Pop-up Trouble Box appears
on the central console advises the
operator of system problems and
contains specific instructions. Entries
in this text box are displayed in the
System Trouble Reported Screen whenever
a system problem occurs that requires
attention. This information usually
includes the name and telephone number
of the designated Security Escort
maintenance technicians.
3.2.4 System Defaults Screen
This screen allows the names for each
class of subscribers to be changed to
match the Security Escort System.
3.2.6 Print System Reports Screen
This screen allows System Reports to be
printed now, scheduled for printing
each night at midnight, or weekly on
Sunday at midnight. To print a report
or reports, check the left-hand box for
each report desired and click Print.
Check Midnight report or Sunday only
checkbox to automatically schedule that
report at those times.
Titles entered into the Subscriber Name
field in the Subscriber Database are
entered here. The system alphabetizes
the Subscriber Database entries by last
name. When a title is entered after the
last name, the entry is alphabetized
incorrectly by title. Entering the
titles used prevents this problem.
Figure 29: Print System Reports
Screen
The labels for the four Information
label fields, in the Subscriber
Database, are also changeable here.
Figure 27: System Defaults Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 32
Daily Test Report
Weekly Maintenance Test Report
Report of testing by classes of
subscriber for the last 24 hrs. broken
down by hour.
Report of maintenance testing for the
last seven days broken down by hour.
Subscriber Check-in Report
Low Battery Report
Report of all subscribers that failed
to check-in during the last scheduled
check-in period.
Report of all subscriber transmitters
currently reporting low battery.
Not Testing Report
Supervision Location Report
Report of all subscriber transmitters
Report of all supervision enabled
that have not tested their transmitters subscribers and their last known
within the last 28 days.
location.
Receivers Not Heard From Report
Print
Report of all receivers that have not
heard transmissions recently. This
could indicate a problem with that
receiver’s ability to hear alarm and
test transmissions.
Clicking this button prints all reports
that are checked in the left-hand check
boxes.
Print Report Now
Daily Trouble Report
Reports with these check boxes checked
are printed when the Print button is
checked.
Report of all the troubles currently
being reported by transponders,
receivers, and alert units.
Midnight Report
Guard Tour Report
Reports are automatically generated
each midnight for all reports that are
checked in the Midnight Report check
boxes.
This selection does not generate a
printed report. However, the Midnight
report and Sunday only checkboxes must
be checked to write a file of the guard
tour information. Another application
like Microsoft Excel can sort and print
the desired reports.
Sunday Report
Reports are automatically generated
each Sunday at midnight for all reports
that are checked in the Sunday Report
check boxes.
Guard Tour Exception Report
The Guard Tour Exception Reports
collected within the last day. Not
currently implemented.
3.2.7 Alarm Report Generation Screen
This dialog allows the alarm reports to
be generated in CSV format.
New Alarm Reports
Alarm reports for all of the new alarms
received by the system.
Figure 300: Alarm Report Generation
Screen
Fail To Test Letters
Notices to all of the subscribers that
have not tested within the last 28
days. Not currently implemented.
Weekly Subscriber Test Report
Report of subscriber testing for the
last seven days broken down by hour.
Weekly Security Test Report
Report of security personnel testing
for the last seven days broken down by
hour.
Weekly Watchman Test Report
Report of watchman personnel testing
for the last seven days broken down by
hour.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 33
To print an alarm report, you may
directly enter the date or press the
ellipsis (…) button in from date, to
date box and select from time, to time
from the respective dropdowns. An alarm
report can also be printed based on the
subscriber details. Select the
Subscriber ID, Subscriber Name,
Transmitter ID or Subscriber Type from
the dropdowns to generate an alarm
report.
This schedule defines the check-in
times
One of the ten schedules can be used to
define the check-in times for those
subscribers that must check-in. Click
on the schedule for the check-in
schedule, highlighting it. Then check
this checkbox, to set the selected
schedule as the check-in schedule. Both
the arm time and disarm time must be
programmed for every day the check-ins
The alarm report can be sorted by Alarm must take place. The arm time is the
Time, Transmitter ID, Subscriber Name, start of the check-in schedule and it
Problem Type, Subscriber Type, by using must occur before the disarm time that
marks the end of the check-in schedule
for that day.
the Sort By dropdown. You can change
the report name and file location by
pressing the … button. Clicking the
Export button saves the generated
report to specified file. Clicking the
Cancel button cancels the report
generation and exits from the Alarm
Report Generation dialog.
Edit Schedule Times
Clicking this button displays the Edit
Schedule Times Screen so the day of
week arm and disarm schedule times can
be edited.
View Alarm Groups
3.2.8 Schedules Screen
Clicking this button displays the View
Alarm Groups Screen. This screen shows
the alarm groups assigned to the
selected schedule and their current
arming state.
This selection informs management of
the ten-time of day/day of week
schedules and holidays. The top portion
of the display shows the ten-time-of-
day/day-of-week schedules that Security
Escort supports. For each schedule,
there is an indication the schedule is
currently active or armed (ACT);
otherwise, the schedule is disarmed
(OFF).
Ignore Holidays for this Schedule
Each schedule can use the holiday dates
as exceptions. If the Ignore Holidays
checkbox is checked or the indicated
holiday dates, the schedules are
activated (armed) that entire day. If
the Ignore Holidays checkbox is not
checked, the normal action of the
schedules take place on the holiday
dates.
Figure 311: Schedule Screen
You may directly enter the date or
press the … button. The holiday dates
do not accept wildcards so you must
enter an entire date.
Figure 32 shows a list of holidays that
can be used as exceptions to the one or
more of the ten schedules.
Figure 322: Holiday selection in the
Schedule Screen
For each day-of-the-week, the arm time
(time the schedule becomes active) and
disarm time (time the schedule becomes
inactive) are displayed. To edit the
arm and disarm times, click Edit
Schedule Times. Double clicking the
number of the schedule allows you to
name the schedules.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 34
If both the disarm time and the arm
Ellipsis (…)
time are programmed and the disarm time
occurs before the arm time (normal –
eight-to-five day), from midnight to
the programmed disarm time the schedule
is active (armed). From the disarm time
to the arm time, the schedule is off
(disarmed). From the arm time to the
end of the day, the schedule is active
(armed).
Clicking this button displays a
calendar where you can graphically
select a date.
Remove >>
Clicking this button removes the
selected date from the holiday dates
list.
<< Add
If both the disarm time and the arm
time are programmed and the arm time
occurs before the disarm time, from
midnight to the programmed arm time the
schedule is off (disarmed). From the
arm time to the disarm time, the
schedule is active (armed). From the
disarm time to the end of the day, the
schedule is off (disarmed).
Clicking this button adds the date
shown to the holiday dates list.
3.2.9 Edit Schedule Times Screen
This screen allows the arming and
disarming times to be programmed for
each of the days of the week. All times
are expressed in 24-hr. time (00:00 to
23:59). Each schedule has one arm time
and one disarm time for each of the
seven days of the week.
Arm Time
This is the time the schedule becomes
active (on or armed) for the selected
day of the week. Times are expressed in
24-hr. time (00:00 to 23:59).
If both the arm time and disarm time
are programmed to 00:00, the schedule
is active (armed) for the entire day.
Disarm Time
If the arm time is 00:00 and the disarm
time is programmed, from midnight to
the programmed disarm time, the
schedule is active (armed) and from the
disarm time to the end of the day the
schedule is off (disarmed).
This is the time the schedule goes off
(disarmed) for the selected day of the
week. Times are expressed in 24-hr.
time (00:00 to 23:59).
Day of the Week
If the disarm time is 00:00 and the arm
time is programmed, from midnight to
the programmed arm time the schedule is
off (disarmed) and from the arm time to
the end of the day the schedule is
active (armed).
Select the day you want to change the
time. The arm time and disarm time are
programmed separately for each day of
the week. You must individually select
each day of the week and set the
desired times.
Figure 333: Edit Schedule Time Screen
3.2.10 View Alarm Groups Screen
Figure 34 shows the alarm groups
assigned to the selected schedule and
their current arming state. The on and
off states indicate the alarm group is
under manual control. Auto is under
control of the selected schedule. The
alarm group is armed if the schedule is
active.
Figure 344: View Alarm Groups Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 35
Off (disarmed)
Clicking this button disarms the alarm
group. The alarm group remains off
(disarmed) until it is manually changed
in this screen to On or Automatic by
schedule.
On (armed)
Clicking this button arms the alarm
group. The alarm group remains on
(armed) until it is manually changed in
this screen to Off or Automatic by
Schedule.
Automatic by Schedule
Clicking this button assigns the alarm
group’s arming state to be controlled
by the indicated schedule. When the
schedule is active (on or armed), the
alarm group is armed. When the schedule
is off (disarmed), the alarm group is
disarmed. Any number of alarm groups
can be assigned to the same schedule.
3.2.1 Alarm Groups Screen
This selection allows setup and
arm/disarm control of the 99 alarm
groups. Any number of point
transmitters can be assigned to an
alarm group in the Subscriber
Database’s Advanced Screen. Each
transmitter can only be assigned to one
alarm group.
First
Clicking this button takes you to alarm
group 1.
An alarm group can be manually armed
and disarmed or assigned to a schedule
to automatically arm and disarm the
alarm group.
Previous
Clicking this button takes you to the
next lower alarm group from the one
displayed. It does not wrap around. It
is disabled at alarm group 1.
Figure 355: Alarm Groups Screen
Next
Clicking this button takes you to the
next higher alarm group from the one
displayed. It does not wrap around. It
is disabled at alarm group 99.
Last
Clicking this button takes you to alarm
group 99.
3.2.72 Alarm Group State Screen
This selection displays a list of the
alarm groups that are armed and have
one or more transmitters (points)
faulted. The points are presented
because they were not restored when
their automatic schedule armed or there
was an alarm while the alarm group was
on.
Alarm Group Name
Enter a descriptive name to identify
the function of the points in this
alarm group.
Alarm Group #
This is the number of the alarm group
(1 to 99).
Arming State of this Alarm Group
The Off, On, and Automatic by schedule
fields control the arming state of this
alarm group.
Figure 366: Alarm Group State Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 36
Acknowledge
Clicking this button closes the screen
if it was selected from the menu.
If the screen appeared automatically at
the end of the check-in period because
some subscribers failed to check-in,
you must enter your password to
acknowledge the screen and remove it
from this computer’s (and all other
computer workstations) screens.
3.2.94 Clear Screen
When selected, clears the map of any
icons and returns to the default map
display.
Print Report
3.2.105 Output Verification
Clicking this button prints the
displayed data to the report printer.
When selected, the system is scanned to
verify that all alarm outputs are in
the correct state. Any output found in
the wrong state is corrected.
Acknowledge
Clicking this button closes the screen
if it was selected from the menu. If
the screen appears automatically at the
arm time of an alarm group’s automatic
schedule because they were not restored
when their automatic schedule armed or
there was an alarm while the alarm
group was on, you must enter your
password to the acknowledge the screen
and remove it from this computer’s (and
all other computer workstations)
screens.
3.2.116 Synchronize System Time
Selecting this option on the master
computer causes the time on the slave
and all of the workstation computers to
be updated to the master computer’s
time.
3.3 Setup Menu
3.3.1 Show History
When selected, the default map display
is replaced by a scrolling text display
showing the most recent events that
occurred in the system. The events
displayed can be selected in the
History Filter Screen under the Setup
Menu. After Show History is selected,
this selection changes to Show Map.
3.2.83 Current Check-in Status Screen
This selection displays a list of the
subscribers that are required to check-
in and failed to do so during the last
check-in period. Also shown are their
addresses, phone numbers, and the last
time they checked in.
Figure 377: Current Check-in Status
Screen
Print Report
Figure 388: Setup Menu
Clicking this button prints the
displayed data to the report printer.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 37
History Screen
This option selects the events
displayed on the computer screen when
Show History is selected.
Printer
This option selects the events sent to
the printer.
3.3.2 History Filter Screen
This screen selects the classes of
events recorded (sent to) for specific
output devices. The Select Destination
box selects the History Screen,
printer, history files, and system
serial ports. Notice when this
History Archive File A
This option selects the events sent to
the a_audit.txt file stored in the
Security Escort sub-directory
(typically C:\escort\a_audit.txt ).
There is a minimum set of events that
cannot be disabled, so they are always
recorded.
selection is changed, the checked items
also change. There is a different set
of events output for each destination
selected. For each destination, the
events to be output must be
History Archive File B
individually configured.
This option selects the events sent to
the b_audit.txt file stored in the
Security Escort sub-directory
(typically C:\escort\b_audit.txt ).
System Serial Port 1
This option selects the events sent to
the System Serial Port 1. System Serial
Port 1 is assigned a physical comm port
in the Remote Comm Port Setup Screen
and the History Filter Output field
must be set in the Remote Setup Screen.
System Serial Port 2
This option selects the events sent to
the System Serial Port 2. System Serial
Port 2 is assigned a physical comm port
in the Remote Comm Port Setup Screen
and the History Filter Output field
must be set in the Remote Setup Screen.
Transponder Restriction
Figure 399: History Filter Screen
This option selects a transponder for
the following restrictions:
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 38
Operator Database Changes
No Restriction: This selection
typically is left at this setting at
all times. The output is not
restricted by an individual
transponder.
Records all changes to the operator
database.
Subscriber Database Changes
Records all changes to the subscriber
database.
Only From Transponder Selected: The
selected events are only output if
they were reported from the
Transponder Database Changes
transponder selected in the
Records all changes to the transponder
database.
Transponder Restriction above.
All from Transponder Selected: All
events are reported from the
transponder selected in the
Transponder Restriction above. The
selected events are reported from
all other transponders in the
system.
Spare 2
Not currently implemented. Leave
unchecked.
Report Database Changes
Records all changes to the Alarm Report
Database.
Alarms
Communications Failure
Outputs the information about an alarm
including location, but not the
transponder and receiver levels. This
is the data typically sent to a
printer.
Records all communication failures and
restorals.
Transponder Communication
Records all communications to
transponders. This selection is only
used for engineering diagnostics.
Leaving this item selected generates a
significant amount of history and fills
up the hard disk drive quickly. Leave
this item unchecked.
Points, Reporting Alarm
Outputs the transponder and receiver
levels for an alarm. Typically, this is
the data too detailed to send to a
printer and is used for diagnostics,
not normal system operation.
Supervision Monitor
Tests, Single Line
Reports changes in the supervision
status for all transmitters that are
being supervised.
Outputs the simple information about a
test. Typically, this is the data
normally sent to a printer.
RF Point Troubles
Tests Including Point Info
Outputs all troubles reported by RF
points. Check this item to monitor
problems with RF points.
Outputs the transponder and receiver
levels for a test. This is the data
usually too detailed to send to a
printer and is used for diagnostics,
not normal system operation. If this
option is selected, Test, Single Line
above, would not be selected for the
same output device.
Transponder Maps
Outputs all transponder status maps.
This selection is only used for
diagnostics. Leave this item unchecked.
Receive Level Maps
Transmitter Low Battery
Outputs all maintenance alarm receive
level maps. This selection is only used
for diagnostics. Leave this item
unchecked.
Outputs low battery reports received
from transmitters.
Operator Activity Log
Database Errors
Outputs all other operator activity
(audit trail) not covered by specific
event selections.
Outputs all reported database errors.
This item is checked.
Preferences Changes
Transponder Troubles
Outputs all changes made to system
preference selections.
Outputs all reported transponder
troubles. This item is checked for
devices used to monitor problems.
Database Backup and Restore
Records all database backup and restore
activity.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 39
When the transponder finds a device
reporting a trouble condition, it
Point Troubles
Outputs all reported receiver and alert
unit troubles. This item is checked for
devices used to monitor problems.
communicates the problem and the device
identity to the central console. This
generates a brief alert tone, displays
a pop-up message for the operator, and
sends an optional pager message. The
message indicates the nature of the
trouble and instructs the operator on
the proper course of action. The status
of the device is recorded in the
Transponder Current Status (See Section
event is recorded on the hard disks of
both the main and backup computers and
on the printout.
Login Changes
Reports all new system operator login
and logout activity.
Network Communications
Records all communications between
networked computers. This selection is
only used for engineering diagnostics.
Leaving this item selected generates a
significant amount of history and fills
up the hard disk drive very quickly and
may bog down the system during high
traffic times. Always leave this item
unchecked.
Figure 40: Pop-Up Alert Showing
Receiver not Responding
Modem Communications
Records all communications to the modem
for remote communications and pager
access. This selection is only used for
diagnosing pager communication
problems. Leave this item unchecked.
Analyze Alarms
This option outputs data allowing an
engineer to evaluate how well the
location algorithm is performing. Leave
this item unchecked.
Master Computer Switch
Records when the master and slave
computers switch roles.
Transponder Data View
Allows the data created by the
Transponder Data View Screen to be
output. This selection is only used for
engineering diagnostics. Leave this
item unchecked.
Printer Output
Selects which trouble categories cause
pop-up messages to appear on the
central console or be sent to the
service pager. The troubles described
below are always recorded in the
Transponder Current Status Screen, but
might or might not produce a pop-up
display or pager message, depending on
the selections made.
Allows the data being sent to the
printer to be sent to other outputs.
This item is unchecked.
3.3.3 Popup Trouble Filter
The Security Escort System contains
many built-in self testing features.
Each transponder tests the condition of
the receivers and alert units connected
to it.
Figure 411: Pop-up Trouble Filter
Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 40
transmission is received by
one or more of the receivers
attached to the transponder,
the transponder activates any
alert units attached to it as
well as the horns and red
LED’s on any of its receivers
which detected the alarm
transmission. Since the
transponder does not have
access to the Subscriber
Database, it must assume that
all transmitters are valid, so
even unauthorized (not in the
Subscriber Database)
transmitters produce audible
alarm indications (if the
System is set for audible
alarms in the Set Security
Preferences Screen).
3.3.4 Transponder Troubles
Popup
The central console also attempts to
reestablish communications by
All troubles with these checkboxes
checked present a popup screen to the
operator when the respective trouble
becomes active.
continually requesting transmissions
from the transponder and listening on
the communications channel. When
communications are restored with the
central console, the transponder
transmits any alarm and trouble
conditions that occurred during the
communications loss, and control of the
horns, LED’s, strobes, and sirens
reverts to the central console.
Pager
All troubles with these checkboxes
checked send a page to the service
pager when the respective trouble
becomes active.
Communications Failure
This approach to managing a
To continually assure that
communications loss assures that alarm
events can not go undetected even if
the central console is out of operation
temporarily.
communications between the central
console and each transponder are
functioning properly, each transponder
is required to send a message to the
central console periodically. If there
is no response from the transponder,
the central console displays a
AC Loss
The transponder senses when it loses AC
power and reports the condition to the
central console. After a few seconds
delay, the central console, displays a
pop-up alert and records the condition
in the audit file. See Section 3.3.10
Communications Failure warning on the
central console and records the
condition in the audit file.
If a transponder determines it lost
communications with the central
console, it assumes control of the
outputs of the devices connected to it
and transmits I’M OK messages until it
is acknowledged by the central console.
Low Battery
Periodically during normal operation,
the transponder tests its battery. If
the test fails, it immediately reports
the condition to the central console.
After a few seconds delay, the central
console displays a pop-up alert and the
condition is recorded in the audit
file.
If during this loss of
communications, an alarm
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 41
Tamper
Tamper
The transponder immediately senses and
reports the actuation of its tamper
Whenever the cover is removed from a
receiver or alert unit, the on-board
switch. The central console immediately microprocessor detects the tamper and
displays a pop-up alert and records the it is reported to the transponder.
condition in the audit file. Tamper
Reports are not delayed by the pop-up
trouble and pager delay.
Tamper reports are not delayed by the
pop-up trouble and pager delay.
No Response
Remote Key Activation
Whenever a receiver fails to respond to
a command from the transponder, a No
Response message is sent by the
The transponder immediately senses and
reports the activation (shorting) of
its remote key input when it is enabled transponder to the central console.
in the Transponder Parameter Screen.
The central console displays a pop-up
alert and records the condition in the
audit file.
This can occur if a multiplex bus wire
is cut or a device is damaged.
Jamming
Each receiver monitors the level of
radio energy being received at all
times. If the level exceeds a preset
threshold, for a preset length of time,
the on-board microprocessor reports
jamming.
Remote Key Tamper
The transponder immediately senses and
reports the fault (open) of its remote
key input when it is enabled in the
Transponder Parameter Screen. The
central console immediately displays a
pop-up alert and records the condition
in the audit file.
Output Device Error
The transponder generates this message
when it commands a receiver or alert
unit to activate or deactivate an
output device (siren, strobe, horn, or
LED) and the device fails to respond
correctly.
Transponder Startup
The transponder reports to the central
console when it first starts up. This
can be caused by a technician turning
the transponder on or by a watchdog
failure of the on board microprocessor.
The central console immediately
Bad Checksum
This message is generated by the
transponder and sent to the central
console whenever the transponder
detects message errors in the
communications between receivers and
alert units.
displays a pop-up alert and records the
condition in the audit file.
Bus Faults
When the transponder is unable to
communicate to any receivers or alert
units on one or more of its multiplex
busses, it immediately reports the
condition to the central console. The
central console reports the condition
by means of a pop-up alert if the
condition persists more than a few
seconds. The condition is also recorded
in the audit file.
3.3.6 Transmitter Supervision Monitor
Known Transmitters
To continually monitor the status of
all transmitters programmed in the
database that send periodic supervision
transmissions. If any monitored
transmitters stop sending supervision
transmissions, a pop-up trouble is
displayed.
3.3.5 Mux Bus Point Troubles
AC Loss
Unknown Transmitters
To monitor for periodic supervision
transmissions from transmitters not
programmed in the database a pop-up
trouble displays if transmissions from
transmitters not programmed in the
database are received.
The microprocessor of the alert unit
detected the absence of AC power. Loss
of AC power affects only the strobe and
siren functions of the alert unit.
Batteries provide backup power for the
strobes and sirens. The logic and
communications functions derive their
power from the multiplex bus.
Monitored Periods
This is the number of supervision
intervals that are consecutively missed
before a pop-up screen reports a
specific transmitter stopped reporting
supervision transmissions.
Low Battery
The alert unit tested for a low battery
condition and the test failed.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 42
3.3.7 Communications Port Monitor
Comm Port Overload
A pop-up trouble screen displays if the
communications traffic to the
transponders exceeds the system is
capability.
Network Comm Failure
A pop-up trouble screen displays if the
communications between the master and
slave computers fails.
3.3.8 Delay To Ignore Troubles That
Auto Reset
Network Comm Failure
A pop-up trouble screen displays if the
communications between the master and
slave computers fails.
Pop-up Trouble and Pager Delay
The delay in seconds before a trouble
displays on the computer screen. If a
restoral for a trouble is received
before a trouble is displayed (this
delay expires), the trouble and the
restoral’s ignored. Tamper troubles are
not delayed.
Map Commands
Diagnostic map commands are used to
determine the status of all devices
(connected to the selected transponder)
with a single command. Maps are
displayed on the History Screen as an
array of rows and columns,
corresponding to point addresses and
bus numbers. The status of a particular
device is shown by a “1” or “0” (zero)
with “1” signifying the true state. The
map location, corresponding to a device
that is not responding to the
3.3.9 Transponder Communications Screen
From the central console, it is
possible to perform detailed diagnostic
tests using the Transponder
Communications Screen. From this
screen, the operator can request maps
indicating the status of each device
connected to a given transponder, and
can control individual devices, turning
LED’s, horns, strobes, and sirens on
and off. The Transponder Communications
Screen appears on the right when it is
opened, allowing the History Screen to
be viewed while the screen is open.
This makes it possible to view the
results of map commands issued from the
console.
transponder, contains a “1” when a Not
Responding Map is selected.
Similarly, a “1” is displayed in
response to a Tamper Map in locations
that correspond to devices in a
tampered state. All other locations
display a “0” (zero), “a” — (if there
is no device assigned to the location),
or a “x”, there is a device connected
to the system at that address, but it
is not in the Transponder Database.
Figure 422: Transponder
Communications Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 43
Device Type Map
Horn – Siren Map
Unlike all other types of map, the
device type map has two characters in
each possible device location. The
right most character indicates the
device type. A “5” indicates a
receiver, “3” indicates an alert unit,
and “7” indicates that the Transponder
Database shows a device in that
Requests a map of all the points that
have their horn or sirens on, on this
transponder. The Horn – Sirens Map
button displays a map with “1” in the
locations corresponding to points which
have their outputs on. A “0” (zero)
indicates that the output is off.
Green LED Map
location but it is not currently
communicating with the transponder. The
left character indicates the following:
“0” (zero), the device is in its normal
state, “1”, the device is off normal,
and “x” there is a device connected to
the system at that address, but it is
not in the Transponder Database.
(Usually this results from an error
during data entry in the Transponder
Database.)
Requests a map of all the points on
this transponder that have their Spare
outputs – Green LED on. The Green LED
Map button displays a map with “1” in
the locations corresponding to points
which have their outputs on. A “0”
(zero) indicates that the output is
off.
Jamming
Requests a map of all the receivers
that are currently reporting RF jamming
to the system. The Jamming button
displays a map with “1” in the
locations corresponding to receivers
that are reporting jamming. A “0”
(zero) indicates that the receiver is
not jammed.
Not Responding Map
Requests a map of all the points that
are not responding (missing) to the
system on this transponder. The
Received Transmission Map button
produces a map display with one in the
locations corresponding to receivers
that are missing from the system. A “0”
(zero) indicates that the point is
responding. An “x” indicates there is a
device connected to the system at that
address, but it is not in the
Tamper
Requests a map of all the points that
are currently reporting a tamper
condition to the system. The Tamper
button displays a map with “1” in the
locations corresponding to points that
are reporting tamper. A “0” (zero)
indicates points that are not tampered.
Transponder Database.
Received Transmission Map
As a means of self-diagnosis, the
system software periodically reviews
the receivers, that have not received
an alarm or test transmission. This
list is printed as a part of the daily
System Status Report and is a tool for
assessing the health of the system. The
Received Transmission Map button
produces a map display with “1” in the
locations corresponding to receivers
which received transmissions. Each time
this map is read, the Received
AC Loss
Requests a map of all the alert units
that are currently reporting an AC
power failure to the system. The AC
Loss button displays a map with “1” in
the locations corresponding to alert
units that are reporting AC Loss.
Restarted
Requests a map of all the points that
are powered up or had a watchdog
failure to the system. The Restarted
button displays a map with “1” in the
locations corresponding to points that
are restarted.
Transmission Map image is cleared in
the transponder.
Strobe – Red LED Map
Requests a map of all the points on
this transponder that have their Strobe
– Red LED on. The Strobe – Red LED Map
button displays a map with “1” in the
locations corresponding to points which
have their outputs on. A “0” (zero)
indicates that the output is off.
Dropped
Requests a map of all the receivers
that have dropped one or more
receptions due to high traffic. The
Dropped button displays a map with “1”
in the locations corresponding to
receivers that dropped one or more
transmissions.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 44
Spare
Out Of Service Map
This is a future option. Not
implemented at this time.
The Out Of Service Map shows those
points (receivers or alert units) that
are currently out of service. Points
may be taken out of service and
Low Battery Map
Requests a map of all the alert units
that are currently reporting a Low
Battery to the system. The Low Battery
Map button displays a map with “1” in
the locations corresponding to points
that are reporting Low Battery.
returned to service by selecting the
point using MUX Bus Point Screen in the
bottom right corner of the screen and
clicking the Point Out Of Service or
Point In Service button. Points can be
selected by typing in the point number
or by using the [+] and [-] buttons, or
the [?] button.
I’m OK Check, I’m OK Release Control
Buttons
Point Out Of Service
These buttons are used to diagnose and
correct communications problems between
the central console and the
transponder. The system software
requires that each transponder send a
message to the central console
periodically if no other communications
have taken place. These messages are
called I’m OK messages. If for some
reason the communications link between
the central console and the transponder
fails, the transponder recognizes the
fact when its I’m OK transmissions are
not acknowledged by the central
Clicking this button takes the
currently selected point out-of-
service. That point no longer responds
to the system, as if it was
disconnected. Use this function with
caution.
Point In Service
Clicking this button restores the
currently selected point to an in-
service condition. That point returns
to normal function.
Transponder Outputs
console. When the transponder has
retried transmitting an I’m OK message
or any other message six times without
acknowledgment, it assumes control of
the outputs (LED’s, horns, strobes, and
sirens) on devices connected to it and
modifies the message to indicate that
it is still OK and has taken control.
These messages are transmitted once per
minute until communications are
Requests the current state of the siren
and strobe outputs on the transponder.
Reset Transponder
Clicking this button resets the
transponder as if it was just powered
up. Any test or alarm processing that
was in progress at the time is lost.
Horn - Siren
reestablished.
If this checkbox is checked, the horn
output of a receiver or the siren
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not changed.
The I’m OK Check button requests that
the transponder send an I’m OK message.
This is used to determine if a
transponder has taken control of its
outputs. The I’m OK Release Control
button generates a command to the
transponder to release control back to
the central console. Normally, the
central console automatically generates
a Release Control message upon the re-
establishment of communications
Green LED
If this checkbox is checked, the green
LED output of a receiver or the spare
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not change.
following a failure.
Strobe – Red LED
If this checkbox is checked, the red
LED output of a receiver or the strobe
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not changed.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 45
Off
Status Screen
When clicked, the checked horn-siren,
green LED and strobe-red LED outputs
are turned off for the selected point
on the selected transponder. If the
output does not change, click On Output
Command and click Off again.
On Output Command
When clicked, the checked horn-siren,
green LED, and strobe-red LED outputs
are turned on for the selected point on
the selected transponder. If the output
does not change, click Off and then
click On Output Command again.
Transponder
Selects the transponder you desire to
communicate with.
Transponder
Selects the transponder you want to see
the status of.
Previous
Returns to the previous transponder.
Next
Total Alarms Received
The total number of alarm messages
received by the central console from
this transponder since the data was
last reset (using the Reset Transponder
Troubles button).
Advances to the next transponder.
Bus X Point Y
This field displays the current bus
number and point number. The actual
point number may be entered in the
field to the right.
Total Tests Received
The total number of test messages
received by the central console from
this transponder since the data was
last reset (using the Reset Transponder
Troubles button).
?
Opens up the Select Point Screen.
+
Advances to the next point.
-
Total Troubles Processed
The total number of trouble messages
received by the central console from
the transponder and processed (see
Total Troubles Shed) since the data was
last reset (using the Reset Transponder
Troubles button).
Returns to the previous point.
Unlimited Retries
When this box is checked, the central
console continues trying to send
commands to a transponder even if the
commands are not being acknowledged.
(Normally, the central console would
cease after six retries and declare a
communication failure.) When this
screen is closed, the system reverts to
the normal six retries.
Total Troubles Shed
During certain rare occurrences, the
communication traffic on the
transponder links becomes excessive and
threatens to increase the system
response time to tests and alarms. This
can happen if faults are reported at a
very high rate. To avoid slow response
in such situations, the central console
may go into a load shedding mode in
which it ceases to record and display
Trouble Reports until the
communications traffic subsides. The
Total Troubles Shed box indicates the
number of trouble messages that were
not processed since the last reset
(using Reset Transponder Troubles
button).
3.3.10 Transponder Current Status
Screen
This screen, accessible from the Main
Menu under the Setup selection,
provides a history of communications
involving the transponder selected in
the transponder box. It also provides
several buttons, that can be used to
diagnose problems with the transponder
and any of its receivers or alert
units.
Figure 433: Transponder Current
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 46
Successful Incoming Messages
Auto Scan
The total number of messages
successfully received from this
transponder.
The auto scan function performs the
above stress test proceeding from one
transponder to the next after one of
each type of map is requested and
received. After the last map type and
before proceeding to the next
transponder, a command is issued to
refresh the transponder data so that
when an auto scan is proceeded through
all transponders, all transponder and
point troubles are updated. Auto scan
is terminated by removing the check in
the Auto Scan box or by closing the
screen using the Cancel button.
Incoming Format Errors
The number of messages received from
this transponder where format error was
detected. This field is yellow if 1.5%
or more of the messages had errors. A
high level of message errors indicates
a serious communication problem.
Incoming Retried Messages
The total number of messages
successfully received from this
Transponder that indicated they were
retried. This field is yellow if 1.5%
or more of the messages are retried. A
high level of retried messages
indicates a serious communication
problem.
Current Troubles
This window displays all current
troubles for this transponder. In the
Current Transponder Status Screen,
there is a low battery and a tamper
condition being reported for this
transponder. This window also displays
the restoration to a normal condition
when it occurs. When the fault is
corrected, clicking the Acknowledge
button eliminates any Restoration
Reports. Conditions, which were not
rectified, remain in the window.
Total Outgoing Messages
The total number of messages sent to
this transponder from the central
console.
Outgoing Retried Messages
The total number of message retries to
this transponder. This field is yellow
if 1.5% or more of the messages are
retried. A high level of retried
messages indicates a serious
Not Responding Map
To assist in diagnosing problems with
the receivers and alert units
associated with a transponder, several
commands can be issued from the central
console to requesting information from
the transponder. This button requests a
map of all the devices on this
communication problem.
Outgoing Failed Messages
This is total number of messages that
could not to be delivered to this
transponder. This field is yellow if
there are any failed messages. Outgoing
failed messages cause the central
console to display an alert message
that communications have failed.
transponder (receivers or alert units)
that are not responding to the system.
The current troubles list is
automatically updated.
Jamming Map
Stress Test
This button requests a map of all the
receivers on this transponder that are
reporting a jamming condition to the
system. The Current Troubles list is
automatically updated.
This checkbox causes the central
console to continually request maps
from the transponder. When in this
mode, the central console sends a new
map request as soon as it receives a
map from the transponder, rotating
through the map types. This test is
used when diagnosing communications
problems to create artificially high
traffic on the communication link
without interfering with the processing
of alarms and tests. The stress test
ceases when the checkbox is cleared, or
this screen is closed by clicking the
Cancel button.
Previous
Returns to the previous transponder.
Next
Advances to the next transponder.
Out of Service Map
This button requests a map of all
devices on this transponder (receivers
or alert units) that were manually
taken out of service to the system. The
current troubles list is automatically
updated.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 47
Tamper Map
Run Silent
This button requests a map of all the
devices on this transponder (receivers
or alert units) that are reporting a
tamper condition to the system. The
current troubles list is automatically
updated.
If checked, the receivers and alert
units on this transponder do not sound
an alarm. This includes alarms received
during a communications failure with
the central console.
Optional Parameter
Acknowledge
This is a future option, leave
unchecked.
Clicking this button removes all
restored troubles from the current
troubles list.
Loop Communications
When this option is checked, the
communications to the transponders are
wired in a loop. The output from the
computer goes to the input of the first
transponder. The output from the first
transponder goes to the input of the
second transponder, and so on until the
output from the last transponder in the
loop goes to the input of the computer.
This form of communications allows
fiber optic communications to be used
(with third party fiber to RS-232
converters).
AC Loss Map
This button requests a map of all the
alert units on this transponder that
are reporting an AC loss condition to
the system. The current troubles list
is automatically updated.
Refresh Data
Clicking this button updates all of the
transponder level data in this screen.
It does not update the device troubles
(use stress test or auto scan to update
the device troubles).
Enable Remote Key
Reset Transponder Troubles
If checked, the remote key supervised
input on this transponder is enabled;
otherwise, it is ignored.
The Reset Transponder Troubles button
is used to reset all of the alarm, test
and message counters to zero, and to
remove any restoration reports.
Uses Proxim Radio
Only check this item if a Proxim radio
is used to communicate to the central
console.
Low Battery Map
This button requests a map of all the
alert units on this transponder that
are reporting a low battery condition
to the system. The current troubles
list is automatically updated.
Comm Fail to Siren Out
If this item is checked, the siren
output on this transponder activates
when a communications failure is
detected at the central console.
3.3.11 Transponder Parameter Change
Screen
Verbose Point Reports
This screen allows parameters stored in
the transponder’s EEPROM memory to be
viewed and changed.
If checked, alarm and test reports
include average levels and packet count
information. This extra information is
for diagnostic proposes only and is not
required for system operation. Since
the additional data increases the
system traffic load leave this item
unchecked.
Figure 444: Transponder Parameter
Change Screen
Test Min Level
This is the minimum receive level (1 to
255) a receiver must see before the
green light displays acknowledging a
successful test. Leave this item at
default (128).
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 48
Test Differential
3.3.12 Transponder Data View Screen
This is the minimum difference in
receive level (1 to 255) a receiver
must be less than the loudest receiver
hearing a test before the green light
displays acknowledging a successful
test. Leave this item at default (64).
This screen is for engineering
evaluation of a transponder only.
Figure 455: Transponder Data View
Screen
Alarm Min Level
This is the minimum receive level (1 to
255) a receiver must see before the
sounder and red light is displayed for
an alarm. Leave this item at default
(1).
Alarm Differential
This is the minimum difference in
receive level (1 to 255) a receiver
must be less than the loudest receiver
hearing an alarm before the sounder and
red light are displayed for an alarm.
Leave this item at default (255).
Byte
These are future options, leave at
default (0).
Spare
This is a future option (leave
unchecked).
Test Transmitter Type
Test Receiver 1
Test Receiver 1
Transmit Delay
Transmit Point
Load Delay
Tamper Load
These parameters are used for
engineering system load testing only.
Do not use in a live system, as they
can generate more traffic than a system
can handle; therefore, actual alarms
may be missed. Leave them at default.
Transponder
Selects the transponder the data is
presented for.
Previous
Returns to the previous transponder in
the system.
Next
Advances to the next transponder in the
system.
Send Change
Sends the changes made to the selected
transponder. Changes are not made to
the transponder EEPROM memory unless
this button is clicked.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 49
3.3.13 Receiver Configuration Screen
Once the receiver and alert unit data
for a transponder is entered into the
Transponder Database, this screen is
used to verify that each receiver is
working and is properly addressed in
the database. This setup tool
identifies errors in the address switch
settings of receivers and alert units,
as well as data entry errors in the
Transponder Database.
RAM Point Info
Views the RAM image of point
information.
RAM Point Stat
Views the RAM image of point status.
RAM Point Trouble
Views the RAM image of point trouble.
RAM EE Mstat Batt
Views the RAM and EEPROM images of
transponder status and battery
condition.
Figure 466: Receiver Configuration
Screen
RAM EE Buss Fault
Views the RAM and EEPROM images of
transponder MUX bus fault condition.
RAM Counters
Views the RAM image of the process
registers.
Save EE
Saves the current RAM image to the
EEPROM memory on the transponder.
EE Point Info
Views the EEPROM image of point
information.
EE Point Stat
Views the EEPROM image of point status.
EE Point Trouble
Views the EEPROM image of point
trouble.
Bus Micro Revision
Views the bus micro revision for the
connected points.
Last MUX Message
Views the last MUX bus message
received.
Put This Receiver In Setup Mode
EE counters
This button initiates the setup process
by causing both the red and green LED’s
of the selected receiver illuminate.
The red and green LED flash. On the
central console, the screen changes
presenting an abort setup for this MUX
Point button. This screen allows
proceeding to the next device in the
event that one receiver is not set up
properly.
Views the EEPROM image of the process
registers.
Clear EE
Clears the EEPROM memory on the
transponder and resets the transponder.
Previous
Returns to the previous transponder in
the system.
The next step is using a Maintenance
Transmitter to transmit an alarm while
standing near the receiver.
Next
Advances to the next transponder in the
system.
Note
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 50
The central console also confirms the
successful setup with an audible and
The illuminated LED’s indicate to
the service person standing near the
device that the receiver is actually
the one currently in the setup mode.
If the LED’s of the designated
receiver are not illuminated, there
is probably an error in the switch
settings of the receiver or an error
in the address in the Transponder
Database. To help resolve such
problems, the person at the central
console can command any device to
illuminate its LED’s and/or sound
its horn.
text message. The abort setup for this
MUX Point button disappears and is
replaced by Test On This MUX Point
Successful button. Click this button to
conclude the test on this point (see
Figure 488: Confirmation of
Successful Setup Test
If the receiver in the Setup Mode
detects the maintenance alarm and if
the received signal is the strongest of
all receivers, the horn on the receiver
sounds briefly and the LED’s go off.
This indicates the receiver is
functioning properly and the receiver’s
address is set correctly in the
Transponder Database and on the
receiver’s switches.
Figure 477: Abort Button to Remove a
Device from the Setup Mode
Auto Advance
If this box is checked, the central
console automatically selects the
receiver with the next higher point
address.
Horn - Siren
If this checkbox is checked, the horn
output of a receiver or the siren
output of an alert unit is turned on if
On is clicked, or off if Off is
clicked. If this checkbox is not
checked, the state of this output does
not change.
Green LED
If this checkbox is checked, the green
LED output of a receiver or the spare
output of an alert unit is turned on if
On is clicked, or off if Off is
clicked. If this checkbox is not
checked, the state of this output does
not change.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 51
Red LED - Strobe
Reset Point
If this checkbox is checked, the red
LED output of a receiver or the strobe
output of an alert unit is turned on if
On is clicked, or off if Off is
clicked. If this checkbox is not
checked, the state of this output does
not change.
Clicking Reset Point causes the
microprocessors on this point to reset
as if they were just powered up. A
receiver should not be reset in a
working system, as it can cause
receptions to be lost.
Ambient
Off
Clicking Ambient causes the system to
interrogate the current ambient levels
of all receivers on this transponder.
When clicked, the checked Horn-Siren,
Green LED, and Red LED - Strobe outputs
are turned off for the selected point
on the selected transponder. If the
output does not change, click On and
then click Off again.
Revision
Clicking Revision causes the system to
interrogate the RF micro revision
levels of all receivers on this
transponder.
On
When clicked, the checked Horn-Siren,
Green LED and Red LED - Strobe outputs
are turned on for the selected point on
the selected transponder. If the output
does not change, click Off and then
click On again.
Jamming
A receiver monitors the ambient level
during normal operation. If the ambient
level rises above the jamming setting
and jamming trouble, it is reported to
the central console. The receiver’s
jamming level can be adjusted by
selecting the appropriate setting
(shown in hexadecimal levels) and
clicking the Jamming button.
Ambient
The Ambient value is shown above Auto
Advance displaying the current ambient
level at the receiver. To get an
updated ambient reading, select the
point, click the Transmit button, and
click the Ambient button.
Jam Map
Clicking Jam Map causes the system to
interrogate the jamming setting levels
of all receivers on this transponder.
RF Micro Version
The receiver’s RF micro revision level
is shown below Auto Advance. To get an
updated reading, click the Revision
button.
3.3.14
Receiver Test Screen
Use this screen to set up and monitor
four receivers and listen to one
receiver transmitting with its Buddy
Check Transmitter. Normally, the
function is for engineering evaluation
of new transmitter and receiver
designs, but it can be used to test
receiver boards and locations in a
working system.
Antenna
Normally, a receiver automatically
switches between its diversity antennas
during normal operation (leave the
default selection on a working system
at this setting). The receiver can be
forced to use only the left or right
antenna, or always switch by selecting
the appropriate setting and clicking
the Antenna button.
Figure 499: Receiver Test Screen
Ant Map
Clicking Ant Map causes the system to
interrogate the current antenna
switching settings of all receivers on
this transponder.
Transmit
Clicking Transmit causes this receiver
to send one test transmission.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 52
Transponder
Run Test
Select the transponder for the
transmitting point and each receiving
point. They can be on the same or
different transponders.
The test only runs when this box is
checked. To stop the test and retain
the test values, uncheck this box.
Spacing
Transmitting Point
This slows the test by forcing this
number of seconds between test
transmissions. Normally, this setting
is left at the default of 0.
Select the point (receiver) on the
selected transponder to generate the
transmissions.
Total Transmissions
Stop Test and Reset Counters
The total number of times the
designated receiver transmitted the
test message.
Clicking this button stops the test and
resets all values.
Close Screen, Does Not Stop Test
Missed all Receivers
Clicking this button closes this screen
The total number of times that the test but does not stop the test from
transmission, was not heard by any of
the designated receivers.
running. Reopening the screen displays
the current progress of the test. The
test should not be left running unless
there is a specific need, as it
Enable Rec
This box must be checked for this
receiver to monitor the test
transmissions.
generates both RF and system traffic.
3.3.15
Network Status Screen
This screen shows the status of
communications on the network, modem,
and system serial ports.
Point
Select the point (receiver) on this
transponder to monitor the test
transmissions.
Figure 500: Network Status Screen
Hits
The number of times this receiver
successfully heard the test
transmission.
Misses
The number of times this receiver
failed to hear the test transmission.
Highest
The left-hand box displays the highest
receive level at which the test
transmission was heard. The right-hand
box displays the greatest number of
packets heard from a single test
transmission.
Successful Incoming Messages
Average
This value is the number of messages
that the system successfully received
on this communications port.
The left-hand box displays the average
receive level at which the test
transmission was heard. The right-hand
box displays the average number of
packets heard from a single test
transmission.
Incoming Communication Errors
This value is the number of messages
that the system detected errors in, on
this communications port. If displayed
in yellow, this value is more than 1.5%
of the Successful Incoming Messages.
Lowest
The left-hand box displays the lowest
receive level at which the test
transmission was heard. The right-hand
box displays the least number of
packets heard from a single test
transmission.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 53
Incoming Retried Messages
Successful Pager Messages
This value is number of successful
receptions that indicated that they
retried by the sending application. If
displayed in yellow, this value is more
than 1.5% of the Successful Incoming
Messages.
This value is the number of successful
pager messages sent.
Failed Pager Attempts
This value is the number of times a
pager message dial-out was
unsuccessful.
Total Outgoing Messages
Reset Status
This value is total number of outgoing
messages sent on this port.
Pressing this button resets all values
shown in this screen.
Outgoing Retried Messages
Refresh Data
This value is number of outgoing
messages that were retried because the
receiving application did not
acknowledge them. If displayed in
yellow, this value is more than 1.5% of
the Total Outgoing Messages.
Pressing this button refreshes all
values shown in this screen. The values
are not automatically updated when the
screen is left open.
3.3.16
System Status Screen
Receiver Buffer Max
This screen shows the status of
internal system queues and
communications on the serial ports
assigned to transponders.
This value is maximum number of bytes
received on this serial port, but not
yet processed by the system. If
displayed in yellow, more than 50% of
the queue was in use.
Figure 511: System Status Screen
Transmit Buffer Max
This value is maximum number of bytes
processed by the system, but not yet
transmitted on this serial port. If
displayed in yellow, more than 50% of
the queue was in use.
Buffer Overflow
This is the number of times a byte was
lost by the software for a serial port
because the input buffer overflowed.
Bytes were placed into the input buffer
faster than the system could process
them.
Maximum Retry Messages
Hardware Overrun
This value is maximum number of
This is the number of times a byte was
lost by the hardware for a serial port
because it was not fast enough to
unacknowledged messages in queue to be
sent to all transponders in the system.
If displayed in yellow, more than 50%
of the queue was in use at this value.
process the byte into the input buffer.
Total Remote Access Connections
Maximum Alarm Messages
This value is the total number of times
a remote access connection was
successful.
This value is the maximum number of
alarms that the system processed at it
busiest time. If displayed in yellow,
more than 50% of the maximum was in
use.
Total Wrong Access Code Attempts
This value is the number of times a
remote access connection was attempted
and rejected because a valid remote
access code was not received.
Maximum Trouble Messages
This value is the maximum number of
troubles in the queue yet to be
displayed. If displayed in yellow, more
than 50% of the queue was in use.
Last Remote Access Time
This is the time and date of the last
successful remote access attempt.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 54
Maximum Low Battery Messages
Overload Level
This value is the maximum number of
transmitters with low batteries yet to
be displayed. If displayed in yellow,
more than 50% of the queue was in use.
This is a measure of the amount of time
peak traffic on this serial port was
greater than the system’s ability to
handle it. The system automatically
sheds non-essential tasks when this
value rises.
Maximum Test Strobe Messages
This value is the maximum number of
test strobes in use at one time. If
displayed in yellow, more than 50% of
the queue was in use.
Overload Count
This is a measure of the number of
times peak traffic on this serial port
was greater than the system’s ability
to handle it. The system automatically
sheds non-essential tasks when this
value rises.
Max Man Down Messages
This value is the maximum number of
transmitters timing man down events, at
one time. If displayed in yellow, more
than 50% of the queue was in use.
Reset Status
Pressing this button resets all values
in this shown in this screen.
Supervision Monitors
This value is the current number of
transmitters being monitored for
supervision transmissions.
Refresh Data
Pressing this button refreshes all
values shown in this screen. The values
are not automatically updated when the
screen is left open.
Max Spooler Bytes
This value is the maximum number of
bytes spooled for the printer at one
time. If displayed in yellow, more than
50% of the queue was in use.
3.3.17 System Preferences Screen
The Set System Preferences Screen under
the Setup Menu contains a number of
settings that govern the behavior of
the Security Escort System.
Max Report Spooler Bytes
This value is the maximum number of
bytes spooled for the printer for Guard
Tour Reports at one time. If displayed
in yellow, more than 50% of the queue
was in use.
Figure 52: System Preferences Screen
Max Receiver Buffer
This value is the maximum number of
bytes received from transponders on
this serial port, but not yet processed
by the system. If displayed in yellow,
more than 50% of the queue was in use.
Max Transmit Buffer
This value is the maximum number of
bytes processed by the system, but not
yet transmitted to the transponders on
this serial port. If displayed in
yellow, more than 50% of the queue was
in use.
Hardware Overrun
This is the number of times a byte was
lost by the hardware for a serial port
because it was not fast enough to
process the byte into the input buffer.
Force Map Background Erase
Buffer Overflow Count
Use this checkbox to erase the map
screen. It should only be checked if
there are problems with icons not being
cleared properly from the screen;
otherwise, it causes the screen to
flicker.
This is the number of times a byte was
lost by the software for a serial port
because the input buffer overflowed.
Bytes were placed into the input buffer
faster than the system could process
them.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 55
Run Buddy Check
Display Maintenance Alarm
This checkbox enables and disables the
buddy check feature of the system.
Normally, when a maintenance alarm is
received from a maintenance transmitter
the red light on all receivers hearing
the transmission flashes for 5 seconds.
If this box is checked, the receiver
with the loudest reception level turns
on both the red and green lights for 5
seconds.
When checked, the central console
periodically issues a command (by the
transponders) to each receiver, to
activate its on-board transmitter. The
console then compares the signals
received from neighboring receivers to
the results of earlier buddy checks,
identifying receivers that appear to
have changed sensitivity.
Sound Maintenance Alarm
If this box is checked, the receiver
with the loudest reception level on a
maintenance alarm turns on its sounder
for 5 seconds. Normally, this box is
not checked.
Day Month Format
Checking this box causes all dates to
be presented in day month year format
rather than the month day year format
used in North America.
Disable Idle Processing
Normally, this software registers with
Windows to return to the Security
Escort System if there is any idle
time. The Security Escort System can
use it to speed up its response to
serial communications and other
background tasks. If checked, the
software is not registered for the idle
time. Normally, this box is not
checked. Windows NT and 2000 can show
the amount of time each application
(task) is taking. When this checkbox is
not checked, it may appear that
Security Escort System is hogging the
processor resources. This is not true
because the Security Escort System is
only taking the time that Windows gives
it through the idle process. To prove
this, check this checkbox. The amount
of time the Security Escort System
needs drops dramatically and the
Security Escort System continues to
operate normally (same communications
responses are slowed by several hundred
milliseconds).
High Speed Buddy Check
Checking this box allows the buddy
check to run as fast as it can.
Normally, only one buddy check
transmission is sent each minute.
Show Maintenance Levels
Checking this box causes the central
console to display the signal strength
measured by each receiver as a number
(from 1 to 15) inside the Receiver icon
when maintenance alarms are displayed;
otherwise, the floor number is
displayed.
Show Test Levels
This checkbox causes signal strength
levels to appear on the receiver icons
when displaying tests on the Main Map
Screen; otherwise, the green Test icons
are displayed.
Enable Algorithm Tweaks
When checked, this checkbox causes the
map scale, alarm spot size, and depth
settings to be displayed in this
screen. It also controls the display of
the SA% and algorithm settings in the
Transponder Edit Screen.
No Buddy Check Delay
If checked, the software does not
impose the hour between buddy checks
from the same receiver. Normally, this
box is not checked and should not be
checked for live systems.
Pager Communications
Normally, this box is not checked. If
checked, the communications to the
dial-up wide area paging system through
the modem displays on the History
Screen. This function is only used to
diagnose communications problems to the
paging system.
No Password To Exit
If checked, the software exits without
asking for a password. Normally, this
box is not checked.
No Password on Reentry
If checked, the software does not ask
for a password when the user switches
to another program and then switches
back to the still running Security
Escort. Normally, this box is not
checked.
Monitor Communications
Normally, this box is not checked. If
checked, the communications to the
modem displays on the History Screen.
This function is only used to diagnose
communications problems with the modem.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 56
identification number of a transmitter
can be automatically entered into the
Subscriber Database. This is used for
entering transmitters when first
issuing them to subscribers and for
transmitter exchanges.
No Password Timeout
If checked, the software does not ask
for a password after the screen saver
has run. Normally, this box is not
checked.
Bring to Front on Alarm
This automatic capture of the
If checked, the software jumps to the
front when a new alarm occurs.
Normally, this box is checked.
Transmitter Identification Number is
accomplished by performing certain
procedural steps (See the Security
Escort Operators Manual) and then using
the transmitter to make a test
Bring to Front on Trouble
If checked, the software jumps to the
front when a Trouble Screen pops-up.
Normally, this box is checked.
transmission in close proximity to a
designated receiver, usually located
close to the central console. By
capturing the Transmitter
Control Room Output to Siren
Identification Number in this manner,
keystroke errors are avoided during
database entries and changes. The
receiver chosen for this purpose is
designated as the ID capture receiver.
To assign the ID capture receiver, its
transponder name and its point number
are selected using the two boxes
labeled transponder and point in the
middle of the Set System Preferences
Screen.
If checked, any time there is an
unacknowledged alarm, the siren output
on the Control Room Output indicated
operates.
Control Room Output to Strobe
If checked, any time there is an
unacknowledged alarm, the strobe output
on the Control Room Output indicated
operates.
Control Room Output to Spare
Control Room
If checked, any time there is an
The Security Escort System can activate
an output to call attention when there
is an alarm that was received and no
operator responded to the system yet.
To assign the control room output,
select the Transponder Name it is
connected to and its point number.
unacknowledged alarm, the spare output
on the Control Room Output operates.
Not Always Top Window
If the Security Escort System is
intended to be the only application
running on this computer, leave this
checkbox unchecked. This prevents other
applications from taking over the
screen. Security Escort System is
always present. If Security Escort
System is to be run on a computer with
other applications, check this box and
Security Escort System shares the
computer’s display like all other
Windows applications. After checking
this box, stop and restart the Security
Escort System for this feature to take
effect. This checkbox is unchecked by
default.
Alarm Zone
Four alarm zones allow the selection of
which alarms from specific transmitters
are reported on this workstation. This
workstation displays the alarms only
for the alarm zones that are checked.
Each transmitter can be assigned to one
or more alarm zones and when that
transmitter generates an alarm (if this
workstation has one or more of the same
alarm zones checked), that alarm is
displayed. The system defaults to all
alarms displayed on all workstations.
Excel Test History Files
Map Scale %’
Do not check this box in a live
Security Escort System. It is for
diagnostic engineering testing only.
This value changes the scale the maps
are presented with. It is not intended
for normal operations but is typically
used for testing to allow more of the
map to be seen. The setting may range
from 30% to 400%. The Enable Algorithm
Tweaks checkbox must be checked for
this to be displayed.
Optional Parameter
These parameters are not currently used
in the system. Leave unchecked.
ID Receiver - Assigning a Receiver For
Automated Transmitter Exchanges
The Security Escort System contains a
feature where the transmitter
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 57
Alarm Spot Size
Medium Depth
This setting changes the size of the
yellow dot that marks the calculated
location of the alarm. The settings
This setting controls the involvement
of receivers in the alarm location
calculation only when the Medium
range from 19 to 76 (half to double the Algorithm is being used. The setting
default alarm dot size). It is best to
set the size of the alarm spot so it
represents a diameter of 15.24 m (50
ft.) on the displayed map (this is the
area where the transmission of the
alarm most likely took place). The
Enable Algorithm Tweaks checkbox must
be checked for this to be displayed.
can range from zero to six (it defaults
to two). When set to zero only, the
receivers that are closer to the actual
location of the alarm considered in the
location calculation. As the setting is
raised, more distant receivers are
included in the alarm calculation.
Typically, lower settings are better
than higher settings. Change this
setting if there are known problems
with the location using the Medium
Algorithm. The Enable Algorithm Tweaks
checkbox must be checked for this to
display.
Linear Depth
This setting controls the involvement
of receivers in the alarm location
calculation only when the Linear
Algorithm is being used. The setting
can range from zero to six (it defaults
to two). When set to zero, only the
Strong Depth
receivers closer to the actual location This setting controls the involvement
of the alarm are considered in the of receivers in the alarm location
location calculation. As the setting is calculation only when the Strong
raised, more distant receivers are
included in the alarm calculation.
Typically, lower settings are better
than higher settings. Change this
setting if there are known problems
with the location using the Linear
Algorithm. The Enable Algorithm Tweaks
checkbox must be checked for this to
display.
Algorithm is being used. The setting
can range from zero to six (it defaults
to two). When set to zero only. the
receivers that are closer to the actual
location of the alarm are considered in
the location calculation. As the
setting is raised, more distant
receivers are included in the alarm
calculation. Typically, lower settings
are better than higher settings. Change
this setting if there are known
Low Depth
This setting controls the involvement
of receivers in the alarm location
calculation only when the Low Algorithm
is being used. The setting can range
from zero to six (it defaults to two).
When set to zero only, the receivers
that are closer to the actual location
of the alarm are considered in the
location calculation. As the setting is
raised, more distant receivers are
included in the alarm calculation.
Typically, lower settings are better
than higher settings. Change this
setting if there are known problems
with the location using the Low
problems with the location using the
Strong Algorithm. The Enable Algorithm
Tweaks checkbox must be checked for
this to display.
3.3.18 Transponder Comm Port Setup
Screen
This screen connects the Comm port
indexes set for each transponder in the
Transponder Database to the physical
Comm ports on the computer.
Figure 533: Transponder Comm Port
Setup Screen
Algorithm. The Enable Algorithm Tweaks
checkbox must be checked for this to
display.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 58
Network Port
This port connects the master and slave
computers of the Security Escort
System. If this system has only a
single computer, this setting should be
set to none.
Modem Port
This port typically connects to the
modem for remote access and pager dial
out.
If set in the Remote Setup Screen, use
this port without a modem for direct
connection to a computer that is always
on line.
System Serial 1
COM
This is a general-purpose serial port.
Its function is set up in the Remote
Setup Screen.
The actual physical Comm port over
which communications to the transponder
are carried.
System Serial 2
Carrier Det
This is a general-purpose serial port.
Its function is set up in the Remote
Setup Screen.
If checked, verify there is no carrier
on the communications port before
communicating. This setting is normally
unchecked.
COM
The actual physical Comm port over
which these communications are carried.
No CTS
If checked, do not monitor the “clear
to send” before communicating. This
setting is normally checked.
Baud
The speed at which characters are
transmitted on this serial port. This
setting must match the baud rate of the
device connected at the other end of
this serial connection. This setting
should always be at the highest speed
both connected devices have in common.
Modem connections are typically much
more efficient, if the baud rate is set
significantly faster than the modems
rated speed (for a 28.8 modem, set the
baud rate to 57600 or 115200). The
default setting is 9600 baud.
Mon Power
If checked, monitor the ring indicator
pin to indicate a remote power supply
used on this Comm link did not fail.
This setting is normally unchecked.
3.3.19 Remote Comm Port Setup Screen
This screen connects the network,
modem, and system serial ports to the
physical Comm ports on the computer and
sets their baud rate.
CR/LF
Figure 544: Remote Port Setup Screen
Appends carriage return and line feed
characters at the end of each string
transmitted (default). Only functions
with the system serial ports (ignored
on the network and modem ports).
CR Only
Appends a carriage return character at
the end of each string transmitted.
Only functions with the system serial
ports (ignored on the network and modem
ports).
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 59
LF Only
Master Computer Answers
Appends a line feed character at the
end of each string transmitted. Only
functions with the system serial ports
(ignored on the network and modem
ports).
Allows the master computer to answer a
remote access after the programmed
number of rings. If the master does not
answer, the slave answers after the
programmed number of rings plus two.
3.3.20 Remote Setup Screen
Slave Computer Answers
This screen sets up the remote access
and system serial port parameters.
Allows the slave computer to answer a
remote access after the programmed
number of rings. If the slave does not
answer, the master answers after the
programmed number of rings plus two.
Generally, it is better to have the
master computer answer remote access
calls.
Figure 555: Remote Setup Screen
Direct Connect Port
The modem port is not connected to a
modem. This setting allows a direct
serial connection to another computer.
This additional computer does not
display alarms, but otherwise behaves
like a slave computer.
Answering Machine Override
If checked, an answering machine is
connected to this phone line. If the
answering machine answers a remote
access call, hang up and redial. When
another call is received within 1 min.
of the last ring of a previous call,
the Security Escort System answers on
the first ring, overriding the
Default Master Computer
This computer is either the only
computer in the system or on startup
this computer defaults to the Master
computer in a live Security Escort
System.
answering machine.
Pulse Dial
Default Slave Computer
If checked, use pulse dial on all
outgoing calls; otherwise, tone dialing
(default) is used.
This computer, on startup, defaults to
the slave computer in a live Security
Escort System.
Answer On Ring
Workstation Computer
Program the number of rings on which to
answer. If there is an answering
machine on this phone line, set the
number of rings to at least two greater
than the number of rings the answering
machine answers. Also check the
This computer is in a live Security
Escort System It can be used for all
operator functions. It cannot control
the system like the master and slave
computers.
Answering Machine Override checkbox.
Remote Computer
Dialing Prefix
This computer is not in a live Security
Escort System. It is used only for
remote access. For this setting to be
enabled, all transponder Comm ports and
the network port must be set to none.
On outgoing calls enter the dialing
prefix, if any.
Password
This is the password that is used to
gain remote access to the Security
Escort System. If the first five
characters of the password match the
remote systems password, read only
access is allowed. If all twelve
characters match, you can change system
parameters remotely.
Emergency Answer Only
Allows the master computer to answer a
remote access only after ten rings. If
the master does not answer, the slave
answers after twelve rings.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 60
Password Verify
Figure 566: Remote Connection Screen
For verification, reenter the same
password as above.
Disabled
If selected, this system serial port is
disabled (default).
History Filter Output
If selected, this system serial port
sends out whatever items are selected
in the History Filter Screen.
Video Switcher Control
Set the modem port and speed in the
If selected, this system serial port
sends out the strings programmed in the
Video Switcher field of the Transponder
Database Edit Screen’s Area data. Also
see Video Switcher Restore.
Remote Comm Port Setup Screen. The
speed selected should be greater than
the speed of the modem and the same as
the speed selected for the remote
system. Use the Backup command under
the Utilities Menu to create a database
backup to floppy. In the Remote Setup
Screen, assign a password and set which
computer (master or slave) is to answer
and the number of rings to answer on.
Also copy the map file from the live
Security Escort System. The map is in
the Escort sub-directory and is named
MAP0.EDB. There also may be other maps
under the names MAP1.EDB, MAP2.EDB, and
so on.
Remote System Control
If selected, this system is controlled
by another system through a proprietary
protocol. This setting can only be used
when two systems are specifically
designed to work together.
Video Switcher Restore
This string is output on any system
serial port programmed for Video
Switcher Control when all alarms are
restored. This string is output to the
video switcher to reset it to the
default displays. Up to twenty
characters can be entered. Control
characters can be entered as [^][A] for
control A.
Modem Init
This is the initialization string
output to the modem to set it up for
all communications except paging.
Normally, this setting does not need to
change. To allow changes to this
string, hold down the [SHIFT] and
[CTRL] keys when this screen first
opens. This string is specific to each
modem model. The default string should
work with most modems.
Modem Reset
This is the reset string output to the
modem. Normally, this setting does not
need to change. To allow changes to
this string, hold down the [SHIFT] and
[CTRL] keys when this screen is first
opened. This string is specific to each
modem model. The default string should
work with most modems.
3.3.21 Remote Connection Screen
This screen sets up the remote access
parameters that allow remote connection
to a live Security Escort System.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 61
In the Security Escort System used for
remote access
Dial
Selecting the desired Security Escort
System and then clicking this button
attempts to connect the selected
Security Escort System. This selection
is only available on the remote
computer; it is not available on a live
Security Escort system.
This screen sets up the remote access
parameters that allow remote connection
to a live Security Escort System.
Program all Comm port indexes in the
Transponder Comm Port Setup Screen to
none. In the Remote Comm Port Setup
Screen, set the network port to none
and set the modem to the Comm port of
the modem. The speed selected should be
greater than the speed of the modem and
the same as the speed selected for the
live system being called. In the Remote
Setup Screen, set the
Answer
This option is only available in a live
Security Escort System. Click this
button manually answers an incoming
call from a remote Security Escort
System.
master/slave/remote setting to remote.
In the Remote Connection Screen select
the Insert button and enter a name,
password, phone number, and three-
character file extension for this
system’s database files. Using a disk
written with the Backup command of the
system you desire access to, restore
the database files. Select the system
you just entered from the dropdown list
box in the Remote Connection Screen.
Exit the Remote Connection Screen and
select Restore Screen under the
Utilities Menu. Restore from the backup
floppy to each databases. When done,
you should also store a copy of the map
file in the Escort sub-directory under
the name MAP0.xxx, (where xxx is the
three-character file extension entered
earlier). After this is done, click
Dial to call the remote system. If
five, eight, or twelve characters of
the password match, you can enter.
Disconnect
Clicking this button drops a remote
connection. This can be done either on
the live system or the remote access
system.
Cancel
Clicking this button closes this screen
but does not disconnect a remote access
connection. At this point, you can
navigate the menus and screens on the
remote system as if you were at the on-
site slave computer system. To drop the
connection, return to this screen and
click Disconnect.
3.3.22 Phone Book Edit Screen
This screen edits existing entries and
adds new phone book entries for remote
system access.
Figure 577: Phone Book Edit Screen
Insert New
Clicking this button presents a blank
Phone Book Edit Screen to enter a new
remote access Security Escort System.
Edit
Selecting the desired Security Escort
System and then clicking this button
allows the existing Security Escort
System data to be edited.
System Name
Delete
This is a reference name for the
Security Escort System to be accessed
remotely. Use to select the desired
system to be accessed in the Remote
Connection Screen.
Selecting the desired Security Escort
System and then clicking this button
deletes the data for the selected
Security Escort System.
Phone Number
The phone number to be dialed to access
the Security Escort System. Enter a
comma for each 2 sec. pause desired.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 62
Access Password
Pager ID
This is the password used to gain
access to the remote Security Escort
This is the ID that identifies the
specific pager this message is to be
System. On the live system being dialed sent to. Many times it is the last
into, set the remote password in the
Remote Setup Screen. If the first five
characters of the password match, the
remote system allows read only access.
If all twelve characters match, you can
change system parameters remotely.
seven digits of the phone number you
would manually dial to access this
pager. The paging company assigns this
value.
Character Limit
This is the maximum number of
characters allowed per page. Typically,
this is set to 80 characters. The
Security Escort System truncates the
pager message at this number of
characters. The paging company assigns
this value.
Verify Password
For verification, retype the password
entered into Access Password.
3 Character System ID
Enter a unique three character ID that
is used as an extension to the map and
database files for accessing this
Security Escort System.
Pages Per Call
This is the maximum number of pager
messages allowed per phone call.
Typically, this is set to four pages
per call. When this number of messages
is sent and there are more messages to
be delivered, the Security Escort
System hangs up and redials the paging
service to deliver the remaining
messages. The paging company assigns
this value.
3.3.23
Pager Setup Screen
This screen sets up remote pager access
for troubles (service) and alarms
(security).
Figure 588: Pager Setup Screen
Pager Group
This is the group of up to eight pagers
this message is sent to. You can
program the individual pager as well as
a group of pagers. The pager group is
sent the page before the individual.
Baud Rate
This is the baud rate used to
communicate with the paging computers.
The paging company assigns this value.
System Name
This identifies the Security Escort
System when multiple Security Escort
Systems report to the same service
pager. Keep this field as short as
possible since these characters, plus a
space, are sent before each trouble
message and are included in the
character limit. If not desired, leave
blank.
Automatically Send Selected Troubles
If checked, send the troubles selected
in the pop-up Trouble Filter Screen to
the service pager.
Phone Number
Phone number to be dialed to access the
paging service. This phone number is
usually different from the number you
manually dial to send a page. The
paging company assigns this value.
System Phone
This presents phone numbers to call in
response to the service page. Only use
if required since these characters,
plus a space, are sent before each
trouble message. They are included with
the system name in the character limit.
If not desired, leave blank.
Password
This is the password that must be sent
to the paging service to send the page.
If not required, leave this field
blank. Usually a password is not
required. The paging company assigns
this value.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 63
Send Installer Demo Alarms
If checked, demo alarms are sent to the
security pager.
Send All Other Alarms
If checked, all actual alarms are sent
to the security pager.
Security Pager Confm Not Reqd
If checked, the confirmation pager
message is not sent to the security
pager when the alarm is acknowledged by
an acknowledgement transmitter.
Cancel Page If Alarm Reset
If checked, the alarm page is canceled
Enter Text to be Sent
if the alarm is reset before it can be
Enter the text to be sent to the pagers
in the large text box at the top of the
screen.
communicated to the paging service.
Send Page a Second Time, 2 Minute Delay
If checked, an alarm page is sent a
second time to the security pager. Do
this in case the pager was in an area
where pages could not be heard when the
first page was sent.
Send Service
Causes the entered message to be sent
to the service pager and service pager
group.
Send Security
Do not resend Alarm page
Causes the entered message to be sent
to the security pager and security
pager group.
If checked, a pager message is sent to
the security person only once till the
alarm is cancelled or acknowledged.
Stop all Pages
Modem Init
Causes all pages currently queued
(automatic or manual) to be aborted and
deleted. Use with caution.
This is the initialization string sent
to the modem to set it up for pager
communications. Normally, this setting
does not need to change. To allow
changes to this string, hold down the
[SHIFT] and [CTRL] keys when this
screen first opens. This string is
specific to each modem model. The
default setting should work with most
modems.
Pager Group
To send a page to all members of a
group, enter the pager group number
here (1 to 99).
Send to Group
Click this button to send the text
entered to the indicated pager group.
3.3.24 Send Pager Message Screen
Allows manually entered messages to be
sent to the service or security pagers.
Service and security pagers are
configured in the Pager Setup Screen.
Individuals and group pager assignments
are set up in the Subscriber Database.
Select Individual
Use this drop down list to select an
individual to page.
Send to Individual
Click this button to send the text
entered to the indicated individual.
Figure 599: Send Pager Message Screen
3.4 Printer Menu
The printer menu allows the alarm and
report printers to be setup and
enabled. You can also print the
contents of the history screen and
files.
Figure 600: Printer menu
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 64
3.4.2 Select Report Printer Screen
Screen
The report printer is used to print all
reports as they are requested
automatically or by the operator.
Typically, the report printer is a page
at a time printer like a laser printer.
Figure 622: Report Printer Screen
3.4.1 Select Alarm Printer Screen
The alarm printer is used to print all
real time event data (alarm, tests,
troubles and so on) as they happen.
Typically, the alarm printer is a
continuous form printer and not a page
at a time printer such as a laser
printer.
Figure 611: Alarm Printer Screen
Enable Printer
Check this checkbox to allow the system
to send the reports to the selected
report printer.
Print to File
Check this checkbox to create file
copies of all reports. This option is
independent of the report printer,
which can also be used at the same
time.
Enable Printer
Check this checkbox to allow the system
to send the real time events to the
selected alarm printer.
Select
Click this button to present the
Window’s System Printer Selection
Screen. This screen is used to select
the report printer from all of the
printers that are installed on this
computer.
Hold Printer Data
Check this checkbox to force the system
to hold the data and not send it to the
selected alarm printer. This is not
recommended operation, but it allows a
page at a time printer to be used as an
alarm printer. Use the Print button to
force the data to print on demand.
Print
Click this button to print the data
that is currently held in Security
Escort’s report printer buffer.
Select
Formfeed
Click this button to present the
Window’s System Printer Selection
Screen. This screen is used to select
the alarm printer from all of the
printers that are installed on this
computer.
Click this button to send a formfeed to
the report printer.
3.4.3 Print History Screen
This selection prints the current data
in the History Screen buffer to the
report printer.
Print
Click this button to print the data
that is currently held in Security
Escort’s alarm printer buffer.
3.4.4 Print File Screen
Enter the name of the file to be
printed or click the Browse button to
open the Common Open File Screen. Then
click the Print button to print the
file to the report printer.
Formfeed
Click this button to send a formfeed to
the alarm printer.
Figure 633: Print File Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 65
This is the standard Windows Common
Open File Screen that is used for
selecting the file to be printed. It
works the same as any other Window’s
standard application.
Figure 644: Common Open File Screen
Databases are not shared: If not
checked, the master and all the slave
and workstation computers share the
same database files. This box must only
be checked if each computer has its own
copy of the databases stored locally.
In normal operation, this box is
typically unchecked. If this box is
checked, the databases must be manually
updated using backup and restore every
time changes are made to the database.
3.5 Network Menu
This is the network menu used to set up
and monitor the TCP/IP network and the
computer’s file paths.
Show connection pop-ups: If checked,
shows a pop-up message box whenever a
network connection is initiated or
released with another computer.
Unchecking this box stops the message
boxes from displaying. In normal
operation, this box is typically
unchecked.
Figure 655: Network Menu
Show all error pop-ups: If checked,
shows a pop-up message box whenever a
network error is reported. Unchecking
this box stops the message boxes from
displaying. In normal operation, this
box is typically unchecked.
3.5.1 System Directories and Network
Address Screen
Disable auto reconnect: If checked,
the system does not automatically
attempt to reconnect a lost connection
each minute. Unchecking this box allows
the system to automatically reconnect a
lost connection. In normal operation,
this box should be unchecked.
Use this screen to set up the Network
IP addresses and ports and related
options. File paths can also be set up.
Figure 666: System Directories and
Network Address Screen
Auto synchronize time: If checked, the
master computer automatically
synchronizes the time on the slave and
workstation computers once each night.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 66
Option 6: This checkbox currently has
no function and should be left
unchecked.
Remote Control Listening Port
The Security Escort will be listening
on this port to communicate with the
OPC Server.
Master’s Network Address: The IP
address of the master computer. There
is no need to program the IP addresses
of the workstation computers into the
Security Escort software since they
always establish the connection with
the master and the slave. The Security
Escort system requires a fixed IP
address for the master computer.
A separate OPC Server is created to
communicate between the OPC Client and
the Security Escort system. The OPC
Server holds the alarm and trouble
messages and sends the same to the
available client once it is connected.
The OPC server will send the status of
the Security Escort to the OPC Client.
The OPC sever also acknowledges and
deletes alarm and trouble messages from
OPC Client. If the connection between
OPC Server and Security Escort goes
down, the OPC server will try to
reconnect with SE. Once the connection
to the SE becomes active, the SE will
send all the available alarms to the
OPC server. The OPC server in turn
sends the alarm back to OPC client;
hence the OPC client may display some
duplicate alarms.
Master's Network Listen Port: A unique
number that indicates the Security
Escort System software is attempting to
set up a connection. Other software
uses different port numbers, allowing
the Network Interface Card to be shared
with other network applications.
Typically, this is set to 4561.
Learn address button. Clicking this
button on the master computer
automatically programs the master’s IP
address in the Master’s Network
Address. If the computer has more than
one Network Interface Card (NIC), you
must verify the correct IP address was
selected by comparing this address to
the IP address that was programmed in
the network control panel TCP/IP
protocol for the master computer’s
network card. If the address is not
correct, manually edit it to the IP
address programmed in the network
control panel TCP/IP protocol for the
master computer’s network card.
Clicking this button on the slave
computer automatically programs the
slave’s IP address in the Slave’s
Network Address field.
Master Database Path: The path this
slave or workstation computer uses to
access the shared database files on the
master computer. This path may have a
different drive letter on the different
slave and workstation computers. They
are typically on the master computer
but they may be on a file server or any
other network accessible drive.
Note:
With version 2.04 of the software it
is possible to use UNC path names
rather than mapping drive letters.
Therefore, the path to the master
computer’s database is
Slave’s Network Address: The IP
address of the slave computer. There is
no need to program the IP addresses of
the workstation computers into the
Security Escort software since they
always establish the connection with
the master and the slave. The Security
Escort System requires a fixed IP
address for the optional slave
computer.
Autobackup to the slave database: If
checked, the slave computer backs up
all databases in the Master Database
Path to the Slave Database Path each
night at 3:00 AM.
Slave Database Path: The path this
master or workstation computer uses to
access the hot backup database files on
the slave computer. This path may have
a different drive letter on the
different master and workstation
computers. They are usually on the
slave computer, but they may be on a
file server or any other network
accessible drive. Typically, they would
not be stored on the same computer as
the Master Database Path so a single
failure would not prevent access to
both the master and slave database
files.
Slave’s Network Listen Port: A unique
number that indicates the Security
Escort software is attempting to set up
a connection. Other software use
different port numbers, allowing the
NIC to be shared with other network
applications. Typically, this is set to
4561.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 67
Note:
With version 2.04 of the software it
is possible to use UNC path names
rather than mapping drive letters.
Therefore, the path to the master
computer’s database is
Local Escort Path: The path on this
workstation the Security Escort was
installed in. Typically, it is
C:\ESCORT.
Backup/Restore to Disk Cartridge Path
When backing up or restoring the
databases to a disk cartridge use this
path.
Subscriber Image File Path
The Security Escort System software can
display an image for each subscriber on
the alarm screen. This parameter tells
the software the path to where the
Successful Incoming Messages
image files are stored. The default is
This value is the number of messages
the system successfully received on
this socket.
C:\ESCORT\IMAGES.
Subscriber Image Extension
The subscriber images can be in JPEG or
Windows Bitmap format. All images in a
system must be in the same format. For
the JPEG format, enter the Windows
extension JPG. For the Bitmap format,
enter the Windows extension BMP.
Incoming Communication Errors
This value is the number of messages
the system detected errors in, on this
socket. If displayed in yellow, this
value is more than 1.5% of the
Successful Incoming Messages.
Subscriber Image Scaling %
Incoming Retried Messages
When the display is set to 640 by 480
pixels and subscriber images are being
displayed, this parameter controls the
image size. This value can range from
10% to 100% and should be adjusted
while viewing alarms to get the desired
image size. When the display is set to
800 by 600 or larger (recommended),
this parameter has no effect.
This value is the number of successful
receptions that indicated that the
sending application retried. If
displayed in yellow, this value is more
than 1.5% of the Successful Incoming
Messages.
Total Outgoing Messages
This value is the total number of
outgoing messages that were sent on
this socket.
3.5.2 Network Socket Status Screen
This screen shows diagnostic
information for the selected TCP/IP
socket.
Outgoing Retried Messages
This value is number of outgoing
messages that must be retried because
the receiving application did not
acknowledge them. If displayed in
yellow, this value is more than 1.5% of
the Total Outgoing Messages.
Figure 677: Current Network Socket
Status Screen
Receive Buffer Max
This value is the maximum number of
bytes that were received on this serial
port, but not yet processed by the
system. If displayed in yellow, more
than 50% of the queue was in use.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 68
Transmit Buffer Max
3.5.4 This Computer's Name and Address
Screen
This value is the maximum number of
bytes that were processed by the
system, but not yet transmitted on this
socket. If displayed in yellow, more
than 50% of the queue was in use.
This screen show the computer’s network
name and current IP address.
Figure 699: This Computer's Name and
IP Address Screen
Reset Status
Pressing this button resets all values
shown in this screen.
Refresh Data
Pressing this button refreshes all
values shown in this screen. The values
are not automatically updated when the
screen is left open.
3.5.3 Winsock Data Screen
This screen shows information about the
Windows Winsock support. This is only
used for diagnostic purposes.
3.6 About Menu
Figure 688: Winsock Data Screen
Figure 700: About Menu
Demo Manual Alarm, Subscriber 1
For demonstration only, it cannot be
used in a live system. Causes the
system to display an alarm from the
subscriber with transmitter ID number
one. In the System Preferences Screen,
check Enable Demo Selections to enable
these demo alarm and trouble
selections. The transponder
communication ports and network
communication ports must also be
disabled and the operator of the system
must login at Installer or Installer
Master authority level.
Demo Lanyard Alarm, Subscriber 2
For demonstration only, it cannot be
used in a live system. Causes the
system to display a lanyard alarm from
the subscriber with transmitter ID
number two.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
EN | 69
Demo Man Down Alarm, Subscriber 3
Demo Maintenance Test
For demonstration only, it cannot be
used in a live system. Causes the
For demonstration only, it cannot be
used in a live system. Simulates a test
system to display a man down alarm from from a maintenance transmitter.
the subscriber with transmitter ID
number three. The man down alarm is
delayed by the programmed man down
delay (usually 10 seconds).
3.6.1 About Screen
The About Screen presents the version
information, copyright data, and
internal processing timers.
Demo Man Down Restoral, Subscriber 3
Figure 711: About Screen
For demonstration only, it cannot be
used in a live system. Restores a
previous man down alarm from the
subscriber with transmitter ID number
two, if it has not timed out and is not
being displayed.
Demo Test Subscriber 1
For demonstration only, it cannot be
used in a live system. Simulates a test
from the subscriber with transmitter ID
number one.
Demo Test Subscriber 2
For demonstration only, it cannot be
used in a live system. Simulates a test
from the subscriber with transmitter ID
number two.
Demo Test Subscriber 3 with low battery
For demonstration only, it cannot be
used in a live system. Simulates a test
from the subscriber with transmitter ID
number three. This test also reports
low battery.
Demo Troubles
For demonstration only, it cannot be
used in a live system. Simulate
troubles from a transponder. Point
troubles are simulated for AC loss,
tamper, and no response. Transponder
troubles are simulated for remote key
and remote key tamper. The individual
troubles can be enabled or disabled in
the pop-up Trouble Filter Screen. The
trouble delay in the pop-up Trouble
Filter Screen also affects these
troubles. For demo purposes, it should
be set to zero.
Software Version
At the top of the screen, the software
version and the date and time that it
was compiled is displayed.
Free Disk Space
This shows the free disk space on the
“C” drive of this computer.
Total Disk Space
This shows the total disk space on the
“C” drive of this computer.
Demo Trouble Restoral
For demonstration only, it cannot be
used in a live system. Simulates
trouble restorals for all the troubles
sent in Demo Troubles.
Tick Time
The amount of time spent in the tick
time processor per pass.
Idle Time
Demo Maintenance Alarm
The amount of time spent in the Idle
Time processor per pass.
For demonstration only, it cannot be
used in a live system. Simulates an
alarm from a maintenance transmitter.
Alarm Time
The amount of time spent to process
each Alarm Report from a transponder.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 4.0 Files Required
For Security Escort
EN | 70
Test Time
The amount of time spent to process
4.0 Files Required For
Security Escort
each Test Report from a transponder.
Other Time
The following files must be in the same
directory as ESC32.EXE (default
c:\escort):
The amount of time spent to process
each trouble and other message reports
from a transponder.
Esc32.exe: the main program
Alarm Location
Bwcc32.dll: support for the Screen
The amount of time spent to compute an
alarm location.
appearance
Tick Passes Hour
Cdrvdl32.dll: communications support
Cdrvhf32.dll: communications support
Cdrvxf32.dll: communications support
Commsc32.dll: communications support
W32mkde.exe: the database manager
The number of passes through the Tick
Time processor that occurred in an
hour.
Idle Passes Hour
The number of passes through the Idle
Time processor that occurred in an
hour.
W32mkrc.dll: support for the
database manager
Serial Number
Wbtrcall.dll: support for the
Displays the serial number of this
Security Escort System installation as
read from the software key.
database manager
Wbtrv32.dll: support for the
database manager
Maximum Users
Lfbmp70n.dll: support for the screen
Displays the maximum number of users
this Security Escort System
images
installation allows. This number is
programmed into the software key.
Lfcmp70n.dll: support for the screen
images
Max Transponders
Ltkrn70n.dll: support for the screen
Displays the maximum number of
images
transponders this Security Escort
System installation allows. This number
is programmed into the software key.
Ltfil70n.dll: support for the screen
images
Max Workstations
Wprefers.edb the workstation
preferences file
Displays the maximum number of
workstations this Security Escort
System installation allows. This number
is programmed into the software key.
The map of the facility is a
standard Windows .BMP (bitmap) file.
It must be stored in the same
directory as ESC32.EXE and be named
"Map0.edb."
Reset Max
Resets all of the max timers.
Map0.edb: map bitmap file
Note:
The following files are the system
databases stored at the Master
Database path:
Operator.edb: the System
Operators Database
Preferen.edb: System Preferences
settings
Reports.edb: Alarm Reports
database
Subscrib.edb: Database of the
Subscribers/ Transmitters
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 5.0 Image Files
Transpon.edb: Database of the
EN | 71
System Configuration
5.0 Image Files
5.1 Map File Generation and
Scaling
Gprefers.edb the Global
Preferences file
Note:
The Security Escort maps are standard
Windows bitmap files (.BMP). Map0.edb
is the default map file, usually the
ground floor in multiple map systems.
The map must be saved in the Security
Escort subdirectory (typically
c:\Escort). These maps can be created
from scratch using any Windows paint
program; however, it is best to scan in
an existing site map. Commercial copy
centers usually have scanners that can
handle larger drawing sizes.
The following sound files should be
in the Windows\media directory:
SEtroubl.wav: trouble sound
SEalarm.wav: alarm sound
Note:
These are sample images for demo and
test. The following files should be
in the \IMAGES directory, which is a
sub-directory to the ESC32.EXE
directory (default
If an AutoCad file is available, have
AutoCad export a bitmap for the best
looking maps that require the least
work to make presentable. If the scale
of the exported map is too large or too
small, re-export the map at the
corrected scale rather than scaling the
map in a graphic editor. Scaling a
bitmap file directly produces a file
that requires a significant amount of
manual effort to make presentable.
c:\escort\images):
Image1.jpg: sample subscriber
image
Image2.jpg: sample subscriber
image
Image3.jpg: sample subscriber
image
Save the scanned image as a Windows
bitmap file (.BMP) with 256 colors (8
bit color). High Color (16 bit) or True
Color (24 bit) can also be used, but
the file sizes is much larger and the
maps are slower to load and may require
more system RAM. It should be scaled so
that the entire map file is at least
800 by 600 pixels (covers the entire
Windows screen). The Security Escort
software auto scrolls the map;
therefore, it is not a problem if the
map is larger than the screen. The map
should not be too large. There should
be enough area of the map on the screen
when an alarm is shown, so there is no
question where in the facility the
alarm is located from a quick review of
the map. A good rule-of-thumb is 100
pixels represents 15.24 m (50 ft.) or
greater.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 6.0 Security Escort
Pager Setup
EN | 72
Screen the path to the images is set in
subscriber image file path (default
location of the images is
5.2 Multiple Map Files
For a multi-story building, the maps
for each floor must have the same
resolution. Each map must be vertically
aligned with all the floors above and
below it. Therefore, the maps have the
same origin (0,0 = upper left corner).
Typically, you would do the map for the
ground floor, then make the maps for
the other floors by editing copies of
the ground floor map.
"C:\ESCORT\IMAGES", but they can be
located anywhere). The three-character
file extension of the image files is
set in Extension (default is JPG).
Subscriber images can also be saved in
Windows bitmap (.BMP); however, this
format requires significantly more disk
storage.
Only when the display is set to 640 by
480 (not recommended) the images
Where transponders from multiple
systems report into the same computer,
the map(s) for each system is separate
and assigned unique map numbers from
the other maps on that same computer.
The origin for the maps for each system
is 0,0 = upper left corner. Therefore,
the location of the receivers in the
transponder database only consider this
system’s map without respect to the
maps for any other systems being
display on top of the map and the
Scaling % (10 to 200) controls the size
of the image (try different settings to
control the image size in the alarm
screen). Under the Files Menu in the
Subscriber Database Screen, select the
desired subscriber and click Edit data.
The image file is the name of file that
has this subscriber’s image. For
example, if the subscriber’s image is
stored in a file with the name
handled by the same computer.
The maps must be named Map0.edb,
Map1.edb through Map99.edb. Where
Map0.edb is the default map file,
usually the ground floor. The Security
Escort software shows the default map
if there is no other events being
processed at a given time.
Image1.jpg, enter Image1 in this box.
You should have a minimum of a 1 MB
video card to display subscriber’s
images. Go to the Windows 95 (Windows
98, Windows NT) Task bar and click the
Start button. Select Settings Control
panel Display. Click the Settings
tab. In the Color palette control you
can select 256 color, High Color (16
bit) or True Color (24 bit). Set the
system to High Color or True Color (256
color is likely to produce undesirable
results). When in doubt, set to High
Color. In the same screen, Desktop area
can be set to 640 by 480, 800 by 600,
or 1024 by 768 pixels. When the display
is set to 640 by 480 (not recommended),
the images are displayed on top of the
map and therefore limit how much of the
map displays. The 1024 by 768 setting
may require too much memory for most
video cards and show more of the map,
decreasing the size of the map details.
Most video cards can be set to 800 by
600 and when in doubt this setting
should be selected. If you cannot
choose these settings, your video card
or monitor setting may be incorrect,
refer to the system documentation to
correct.
Assign the desired map number to an
area or point in the transponder
database. Assign the map for a fixed
location transmitters in the Subscriber
Database Advanced Screen.
5.3 Subscriber Images
Display subscriber images. This
software does not capture the
subscriber images; it displays images
that were previously captured by some
other means. The subscriber image can
be captured using a digital camera,
video capture board and so on. The
source of the image is not critical. We
have not identified, nor do we require
a specific manufacturer of the image
capture equipment. The images must be
saved individually in JPG format. The
images should not be larger that 160
pixels wide and 160 pixels high. If
they are, they are scaled and therefore
they may loose image quality. Under the
Setup Menu in the System Preferences
6.0 Security Escort Pager
Setup
With version 1.10 and higher, Security
Escort supports:
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 6.0 Security Escort
Pager Setup
EN | 73
For dial-up paging systems, the paging
company assigns the phone number and
Pager ID. Typically, the pager ID is
the last seven digits dialed to access
the pager from a phone.
Up to 256 individual alphanumeric
pagers; grouped into 99 groups of
eight.
Both dial up and local serial port
connected paging systems, in the
same system, at the same time.
Service pages page the members of the
service group first, followed by the
single service pager.
Service pages that can activate a
group of eight service pagers in
addition to a single pager.
Alarm pages page the members of the
alarm area paging group first (if any),
followed by the alarm group, and
finally the single alarm pager.
Alarm pages that can activate a
group of eight alarm pagers in
addition to a single pager. All
alarms located in an alarm area can
page an additional group of eight
pagers specific to that area.
6.1 Dial-up Paging Modem Setup
All dial-up pager access is through the
modem. The baud rate set up in the
Remote Comm Port Setup Screen under the
Setup Menu for the modem port is for
remote access to the Security Escort
System and not for pager dial-up
Manual pages sent to any individual
pager or pager group.
All paging system communication
using the TAP or PET protocols. This
is true for both the dial-up and
local serial port connected paging
systems. Currently there is no
support for any other pager
protocols.
access. Leave this baud rate at the
correct setting for remote access.
6.2 Local Paging Setup
The local paging system is accessed
through a system serial port. Assign
System Serial Port 1 or 2 to the
computer port to be used in the Remote
Comm Port Setup Screen under the Setup
Menu. Also configure the baud rate to
match the local paging system
The system does not support numeric
only or vibrate only pagers.
At this time, the only local paging
system tested is TEKK model: PT-400
(Tekk Inc., 226 N. W. Parkway, Kansas
City, MO, Phone (816) 746-1098, Fax
(816) 746-1093).
(typically 9600 baud).
In the Remote Setup Screen, assign
System Serial Port 1 or 2 as the
destination for Local Service Pages,
Local Security Pages, or All Local
Pages.
Set the DIP switch for TAP Mode,
9600N81, Switch 6 off, all other
switches on.
The pager ID to be used for each pager
is the seven-digit CAP code that is on
a label on the back of the pager (such
as 0991001). A three-digit code must be
appended to the end of the CAP code.
For example, 0991001ERF where E is the
Message Encoding Type, R is the RF data
rate, and F is the Function Code.
Message Encoding Type (E) must be a “1”
for alphanumeric coding.
RF data rate (R) is “5” for 512 BPS,
“1” for 1200 BPS, or “2” for 2400 BPS.
Many systems use 512 BPS for more
reliable transmissions.
Figure 722: Remote Setup Screen
Function Code (F) may be set to one
through four for a specific function
code or zero for the default (recommend
the Function Code be set to zero).
For an alphanumeric pager communicating
at 512 BPS, the pager ID in our example
is 0991001150.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 6.0 Security Escort
Pager Setup
EN | 74
If service or alarm pages are enabled,
either the paging group or individual
pager must be filled in. They may both
be filled in if desired.
The baud rate assignments in this
screen affect only the dial-up paging
access through the modem (get the
desired baud rate from the paging
company). These baud rate selections
have no effect on local paging systems
or remote system access. Remember that
dial-up pages may be routed to
different paging companies and they may
require different baud rates. Set the
baud rate to the highest baud rate
common to all of the paging companies
to be accessed.
6.3 Service and Security (Alarm)
Pager Setup
Pager access is setup in the Pager
Setup Screen under the Setup Menu.
Refer to the Pager Setup Screen for the
details not covered here.
The character limit (characters per
page), pages per call affect all pages
of the indicated type (local and dial-
up). These fields must be set to the
lowest setting for any of the routes
that may be used. Remember that dial-up
pages may be routed to different paging
companies and they may have different
restrictions.
Figure 733: Pager Setup Screen
6.4 Subscriber (Individual)
Pager Setup
In the Subscriber Database, select the
record for the desired individual.
Press Edit data then press Advanced.
The screen displays.
The pager ID is required for all
individual pagers dial-up and local. If
the phone number and password are
assigned, the page is sent over the
modem connection. If the phone number
and password fields are blank, the page
is routed to the local paging system.
If you do not desire this individual to
have pager support, leave the phone
number, password, and pager ID fields
blank.
For both the service and security
pagers, an individual pager (phone
number, password, and pager ID) can be
assigned. The pager ID is required for
all individual pagers, dial-up and
local. If the phone number and password
are assigned, the page is sent over the
modem connection. If the phone number
and password fields are both blank, the
page is routed to the local paging
system. If you do not desire an
individual pager, leave the phone
number, password, and pager ID fields
blank.
Both the service and security pagers
also support paging groups. If a group
number is programmed in the pager group
field, all the members of that group
are paged for every service or alarm
page.
Figure 744: Subscriber Database
Advanced Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 6.0 Security Escort
Pager Setup
EN | 75
The default alarm pager group defined
in the Pager Setup Screen is paged
after the pager group assigned to an
area. If a pager group is not assigned
to an area or the alarm location is not
within a defined area, only the default
pager group is paged.
If the pager information is entered,
this individual may be assigned to
three paging groups. Each group accepts
eight members maximum. Remember, it
takes time to communicate with a paging
service; therefore, only add members to
a group if they need to be there.
Otherwise, you may slow the paging
report to people that must respond.
6.6 Manual Pages
Select the Send Pager Message Screen
under the Setup Menu to send manual
pages.
Type the desired message in the large
text box on the top.
To send the page to all members of
the default service pager group,
click Send Service.
A pager group may contain
members accessed by the local
paging system and members that
require dial-up access. Dial-up
access typically takes much
longer and it may slow pages to
the local paging system.
To send the page to all members of
the default security pager group,
click Send Security.
To send the page to all members of a
specific pager group, enter the
desired group number in the pager
group field and click Send to group.
6.5 Alarm Area Setup
In the Transponder Database under the
File Menu, select the transponder with
the desired programmed alarm area. Then
click Edit data. Click Show areas and
select the area desired.
To send the page to an individual,
click the down arrow to display a
list of the individuals that are
programmed in this system. Select
the desired individual by clicking
on their name with the left mouse
button, then click Send to
The pager group field may be programmed
with a pager group that is paged if
this area is the most likely location
of an alarm. This pager group is the
first group paged to allow quick
individual.
response by those individuals charged
with responding to an alarm in this
area. Each area may be assigned a pager
group that can be the same or different
from other alarm areas.
Figure 766: Send a Pager Text Message
Screen
Figure 755: Transponder Area Edit
Screen
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual |
EN | 76
7.0 Importing a
Subscriber Database
This section describes the file format
required to import data into the
Subscriber Database. There is no way to
undo this operation, therefore, DO A
DATABASE BACKUP FIRST and verify the
updated data before the changed
database is placed in service. If there
are problems, restore the Subscriber
Database from the backup.
The file of new data record entries
must be in tab delimited text format.
It must be placed in the Security
Escort subdirectory (typically
C:\Escort) and be named TABMERGE.DAT.
The data fields must be in the
following order, delimited by the
horizontal tab character (decimal 8),
and the record must be terminated with
a carriage return (decimal 13). If a
data field has no data, store the
terminating tab character for that
field. The total number of characters
in all the fields of a record must be
255 characters or less, including the
tab and carriage return characters.
After the TABMERGE.DAT file is stored
in the Security Escort subdirectory,
start ESC32.EXE, enter the Subscriber
Database, and click the DATA MERGE
button. Be patient, it may take a
while. Watch for the disk activity to
stop. After the data is successfully
merged, it is a good idea to remove the
TABMERGE.DAT file to disable the DATA
MERGE feature.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 7.0 Importing a
Subscriber Database
EN | 77
Table 1:Importing a Subscriber Database
Data Fields in
Required Order
Excel
Column
Restrictions
Subscriber Name
A
B
C
This field can be up to 30 characters. This field can contain any
printable ASCII character except the “?”.
Subscriber ID
This field can be up to twelve characters. This field can contain
only ALPHA, numeric and the dash ASCII characters.
This field can be up to sixteen characters. This field can contain
only numeric, “#”, “*”, “(“, “)”, comma and the dash ASCII
characters.
Here Phone
Number
Here Address 1
Here Address 2
Here City
D
E
F
G
H
I
This field can be up to 30 characters. This field can contain any
printable ASCII character except the “?’.
This field can be up to 30 characters. This field can contain any
printable ASCII character except the “?”.
This field can be up to twenty characters. This field can contain
any printable ASCII character except the “?”.
This field can be up to three characters. This field can contain
only ALPHA ASCII characters.
This field can be up to ten characters. This field can contain only
ALPHA, numeric and the dash ASCII characters.
This field can be up to sixteen characters. This field can contain
only numeric, “#”, “*”, “(“, “)”, comma and the dash ASCII
characters.
Here State
Here Zip
Away Phone
Number
Away Address 1
Away Address 2
Away City
J
K
L
M
N
O
P
Q
R
S
T
U
V
This field can be up to 30 characters. This field can contain any
printable ASCII character except the ‘?’.
This field can be up to 30 characters. This field can contain any
printable ASCII character except the “?”.
This field can be up to twenty characters. This field can contain
any printable ASCII character except the “?”.
This field can be up to 3 characters. This field can contain only
ALPHA ASCII characters.
This field can be up to 10 characters. This field can contain only
ALPHA, numeric and the dash ASCII characters.
This field can be up to 254 characters. This field can contain any
printable ASCII character except the “?”.
This field can be up to 254 characters. This field can contain any
printable ASCII character except the ‘?”.
This field can be up to 254 characters. This field can contain any
printable ASCII character except the “?”.
This field can be up to 254 characters. This field can contain any
printable ASCII character except the “?”.
This field can be up to 16 characters. This field can contain only
numeric, “#”, “*”, “(“, “)”, comma and the dash ASCII characters.
This field can be up to 6 characters. This field can contain only
numeric, and ALPHA ASCII characters.
This field can be up to 10 characters. This field can contain only
numeric ASCII characters.
0 Unclassified, 1 Commuter, 2 Faculty, 3 Resident, 4 Security, 5
Staff, 6 Installer, 7 Out of Service, 8 Watchman, 9 Visitor, 10
Point type, 11 Acknowledgement. This field should contain only
numeric ASCII characters.
Away State
Away Zip
Supplemental
Text Field 1
Supplemental
Text Field 2
Supplemental
Text Field 3
Supplemental
Text Field 4
Pager Phone
Number
Pager Password
Pager Pager ID
Subscriber Type
Handicapped Type W
0 No handicap, 1 Blind, 2 Deaf, 3 Handicapped, 4 Wheel chair. This
field should contain only numeric ASCII characters.
Transmitter ID
Away Name
X
Y
Z
This field may be up to 9 characters. This field should contain only
numeric ASCII characters.
This field can be up to 30 characters. This field can contain any
printable ASCII character except the “?”.
This field can be up to 30 characters. This field can contain any
printable ASCII character that is valid for a file name.
Image Filename
Height Feet
Height Inches
AA
AB
0-7, This field should contain only numeric ASCII characters.
0-11, This field should contain only numeric ASCII characters.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | 7.0 Importing a
Subscriber Database
EN | 78
Table 1:continued
Data Fields in
Required Order
Excel
Column
Restrictions
Build Code
Hair Color
Eye Color
AC
AD
AE
0 Medium, 1 Slim, 2 Large. This field should contain only numeric
ASCII characters.
0 Brown, 1 Auburn, 2 Black, 3 Blond, 4 Brunet, 5 Grey, 6 Red. This
field should contain only numeric ASCII characters.
0 Brown, 1 Blue, 2 Green, 3 Hazel, 4 Grey. This field should contain
only numeric ASCII characters.
Pager Group A
Pager Group B
Pager Group C
Fixed Floor
Level
AF
AG
AH
AI
0-99, This field should contain only numeric ASCII characters.
0-99, This field should contain only numeric ASCII characters.
0-99, This field may contain only numeric ASCII characters.
0 Basement5, 1 Basement4, 2 Basement3, 3 Basement2, 4 Basement1, 5
Tunnel, 6 Basement, 7 Ground, 8 Outside, 9 Floor 1, 10 Floor 2, 11
Floor 3, 12 Floor 4, 13 Floor 5, 14 Floor 6, 15 Floor 7, 16 Floor 8,
17 Floor 9, 18 Floor 10, 19 Floor 11, 20 Floor 12, 21 Floor 13, 22
Floor 14, 23 Floor 15, 24 Floor 16, 25 Floor 17, 26 Floor 18, 27
Floor 19, 28 Floor 20, 29 Floor 21, 30 Floor 22, 31 Floor 23, 32
Floor 24, 33 Floor 25, 34 Floor 26, 35 Floor 27, 36 Floor 28, 37
Floor 29, 38 Floor 30, 39 Floor 31, 40 Floor 32, 41 Floor 33, 42
Floor 34, 43 Floor 35, 44 Floor 36, 45 Floor 37, 46 Floor 38, 47
Floor 39. This field should contain only numeric ASCII characters.
Fixed Map X
Location
Fixed Map Y
Location
Fixed Bitmap
Number
Supervision
Interval
AJ
AK
AL
AM
This field can contain only numeric ASCII characters.
This field can contain only numeric ASCII characters.
0-99 This field can contain only numeric ASCII characters.
0 None, 1 is 90 Second Supervision, 2 is 30 Second Supervision, 3 is
1 Hour Supervision. This field can contain only numeric ASCII
characters.
Alarm Group
Shorted Loop
Open Loop
Status
Enable Magnetic
Reed
AN
AO
AP
AQ
AR
0-99, This field can contain only numeric ASCII characters.
This field can contain only numeric ASCII characters.
This field can contain only numeric ASCII characters.
Encoded value. Do not change.
This field can contain only numeric ASCII characters.
Fixed Location
Text
Magnetic Reed
Text
Shorted Loop
Text
Open Loop Text
AS
AT
AU
AV
This field can be up to 254 characters. This field can contain any
printable ASCII character except the “?”.
This field can be up to 30 characters. This field can contain any
printable ASCII character except the “?”.
This field can be up to 30 characters. This field can contain any
printable ASCII character except the “?”.’
This field can be up to 30 characters. This field can contain any
printable ASCII character except the “?”.
Status Flags
Modify Op
Test Time
Last Transmitter AZ
Change
AW
AX
AY
Encoded value. Do not change.
0-30000, this field can contain only numeric ASCII characters.
Encoded 32-bit time value. Do not change.
Encoded 32-bit time value. Do not change.
Spare Date
Last Fail To
Test Letter
BA
BB
Encoded 32-bit time value. Do not change.
Encoded 32-bit time value. Do not change.
Created
BC
BD
BE
BF
BG
BH
BI
BJ
Encoded 32-bit time value. Do not change.
Encoded 32-bit time value. Do not change.
Encoded 32-bit time value. Do not change.
This field should be blank.
This field should be blank.
This field should be blank.
Modified
Low Battery
Spare2
Spare3
Spare4
Spare5
Number Of Tests
This field should be blank.
This field may contain only numeric ASCII characters.
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Index
EN | 79
Arm Time .....................................................................34
Arming State of this Alarm Group................................35
Auto Advance ...............................................................50
Auto Scan .....................................................................46
Auto Silence Alarm In X Seconds ................................30
Auto synchronize time ..................................................66
Autobackup to the slave database .............................66
Automatic by Schedule.................................................35
Automatically Send Selected Troubles.........................62
Average.........................................................................52
3
3 Character System ID..................................................62
A
Abort setup for this MUX Point ...................................50
About menu ..................................................................68
About Screen ................................................................69
AC Loss............................................................40, 41, 43
AC Loss Map................................................................47
Access Password...........................................................62
Acknowledge..........................................................36, 47
Add ...............................................................................34
Alarm............................................................................56
Central Console response to .....................................11
Central Console screen display of.............................11
Maintenance..............................................................14
Multiple, simultaneous..............................................12
Sequence of occurrences...........................................10
Alarm Differential.........................................................48
Alarm Group.................................................................17
Alarm Group #..............................................................35
Alarm Group Name ......................................................35
Alarm Group State Screen............................................35
Alarm Groups ...............................................................35
Alarm Location.............................................................70
Alarm Min Level ..........................................................48
Alarm on Open Loop....................................................16
Alarm on Shorted Loop ................................................16
Alarm Pager Setup........................................................74
Alarm Spot Size............................................................57
Alarm Time...................................................................69
Alarm type definitions ..................................................31
Alarm Voice Output .....................................................29
Alarm When Armed, Trouble When Disarmed on Open
Loop..........................................................................16
Alarm when armed, trouble when disarmed on shorted
loop...........................................................................16
Alarm Zone...................................................................57
Alarms ..........................................................................38
Alert..............................................................................23
Alert Unit
B
Backup..........................................................................27
Backup Screen..............................................................26
Backup/Restore to Disk Cartridge Path ........................67
Bad Checksum..............................................................41
Baud..............................................................................59
Baud Rate .....................................................................62
Beginning......................................................................19
Bring to Front on Alarm ...............................................56
Bring to Front on Trouble.............................................56
Buddy Check ................................................................55
Buffer Overflow............................................................53
Buffer Overflow Count.................................................54
Bus -..............................................................................21
Bus +.............................................................................21
Bus fault........................................................................41
Bus Micro Revision......................................................49
Bus X Point Y...............................................................45
Byte...............................................................................48
C
Cancel.....................................................................25, 61
Cancel Page If Alarm Reset..........................................63
Carrier Det....................................................................58
Cartridge.......................................................................67
Cartridge Disk Drive...............................................26, 27
Central Console ..............................................................9
Function of..................................................................9
Response to Alarm....................................................11
Central Console Response ............................................12
Character Limit ..........................................................62
Classic algorithm ..........................................................23
Clear EE........................................................................49
Clear Entire File............................................................27
Clear Screen..................................................................36
Close Screen, Does Not Stop Test................................52
COM.............................................................................58
Comm Fail to Siren Out................................................48
Comm Port Index..........................................................18
Comm Port Overload....................................................42
Communications
Function of..................................................................8
Alert Unit Point Type ...................................................22
Alert Units To Receivers ..............................................23
Algorithm......................................................................23
All from Transponder Selected..................................38
Ambient ........................................................................51
Analyze Alarms ............................................................39
Answer..........................................................................61
Answer On Ring ...........................................................60
answering machine........................................................60
Answering Machine Override.......................................60
Ant Map........................................................................51
Antenna.........................................................................51
Area Number ................................................................20
failure of ...................................................................40
Stress test of..............................................................46
Communications Failure...............................................38
Computer
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Index
EN | 80
Master.......................................................................59
Remote......................................................................59
Slave .........................................................................59
Workstation ..............................................................59
Console screen showing "Test" Icons...........................12
Contact Information......................................................31
Control Room ...............................................................57
Control Room Output to Siren......................................56
Control Room Output to Spare .....................................56
Control Room Output to Strobe....................................56
Copy .......................................................................19, 25
CR Only........................................................................59
CR/LF...........................................................................59
Created..........................................................................18
CTS Control................................................................58
Current Check-in Status................................................36
Current Troubles...........................................................46
Cut ................................................................................25
Edit Data.......................................................................19
Edit Schedule Times.....................................................34
Edit Schedule Times.....................................................33
Edit Subscriber’s Advanced Features Screen ...............15
EE counters...................................................................49
EE Point Info ................................................................49
EE Point Stat.................................................................49
EE Point Trouble ..........................................................49
Ellipsis (…) ..................................................................34
Emergency Answer Only..............................................59
Enable Algorithm Tweaks ............................................55
Enable Printer ...............................................................64
Enable Rec....................................................................52
Enable Reed Switch......................................................16
Enable Remote Key ......................................................48
End of File ....................................................................19
End Of Shift Reminder .................................................30
Excel Test History Files................................................56
Exit ...............................................................................26
D
F
Daily Test Report..........................................................32
Daily Trouble Report....................................................32
Database Backup and Restore ......................................38
Database Errors ............................................................39
Database Find Level .....................................................30
Databases are not shared...............................................65
dates..............................................................................55
Day Month Format .......................................................55
Day of the Week...........................................................34
Default Master Computer .............................................59
default password...........................................................13
Default Slave Computer................................................59
Delete............................................................................61
Delete Point ..................................................................19
Demo Alarm .................................................................68
demo alarms..................................................................63
Demo Test ....................................................................69
Demo Troubles .............................................................69
Device Type Map .........................................................43
Dial...............................................................................61
Dialing Prefix ...............................................................60
Dial-up paging modem setup........................................73
Direct Connect Port ......................................................59
Disable auto reconnect..................................................65
Disable Idle Processing ................................................55
Disable Open Loop.......................................................16
Disable Shorted Loop ...................................................16
Disabled........................................................................60
Disarm Time.................................................................34
Disconnect ....................................................................61
Display Maintenance Alarm .........................................55
Display Unauthorized Alarms.......................................28
Done.............................................................................17
Dropped........................................................................43
Fail To Test Letters.......................................................32
Failed Pager Attempts...................................................53
File Menu......................................................................13
Filter virtual fence.........................................................28
First...............................................................................35
Fixed Location and Pager Text.....................................16
Fixed Location Transmitter.......................................15
Floor .............................................................................24
Floor Level .............................................................15, 23
Floppy A.......................................................................27
Force Map Background Erase ......................................55
Formfeed.......................................................................64
Free Disk Space............................................................69
G
Green Led ...............................................................44, 50
Green Led Map.............................................................43
Guard Tour Exception Report ......................................32
Guard Tour Level .........................................................30
Guard Tour Minutes .....................................................30
Guard Tour Report .......................................................32
H
Hardware Overrun ..................................................53, 54
High Speed Buddy Check.............................................55
Highest..........................................................................52
History Archive File A..................................................37
History Archive File B..................................................37
History Filter Output.....................................................60
History Filter Screen.....................................................37
History Screen ..............................................................37
Hits ...............................................................................52
Hold Printer Data..........................................................64
Horn - Siren ............................................................44, 50
Horn – Siren Map .........................................................43
E
Edit ...............................................................................61
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Index
EN | 81
I
Alert Unit..................................................................41
Transponder..............................................................40
Low Battery Map....................................................44, 47
Low Battery Report ......................................................32
Low Depth ....................................................................57
Low pull algorithm .......................................................23
Lowest ..........................................................................52
I’m Ok Check ...............................................................44
I’m OK message ...........................................................44
I’m Ok Release Control................................................44
ID Receiver...................................................................56
Idle Passes Hour ...........................................................70
Idle Processing Disable ................................................55
Idle Time ......................................................................69
Ignore Communications Failure....................................18
Ignore Holidays for this Schedule.................................33
Image File Path.............................................................67
Importing a Subscriber Database..................................76
Incoming Communication Errors............................52, 67
Incoming Format Errors................................................46
Incoming Retried Messages..............................46, 53, 67
Insert New.........................................................19, 20, 61
Installer Alarms Silent ..................................................29
Isolate From All Other Transponders For Location......18
M
Maintenance "Alarm" ...................................................14
Maintenance Alarm.................................................14, 55
Maintenance Transmitter ..........................................8, 49
Use in setup mode.....................................................49
Man Down Delay Timer X Seconds.............................30
map ...............................................................................61
Map...............................................................................24
Device type, interpreting...........................................43
Status, commanding and interpreting........................42
Map File Generation.....................................................71
Map File Scaling...........................................................71
Map Number.................................................................15
Map Scale %.................................................................57
Map X Position.............................................................15
Map Y Position.............................................................15
Master Computer ..........................................................59
Master Computer Answers............................................59
Master Computer Switch ..............................................39
Master Database Drive ...........................................26, 27
Master Database Path ...................................................66
Master’s Network Address ........................................66
Master's Network Listen Port ...................................66
Max Man Down Messages............................................54
Max Receiver Buffer ....................................................54
Max Report Spooler Bytes............................................54
Max Spooler Bytes .......................................................54
Max Transmit Buffer ....................................................54
Max Transponders........................................................70
Max Workstations.........................................................70
Maximum Alarm Messages ..........................................53
Maximum Low Battery Messages.................................54
Maximum Retry Messages............................................53
Maximum Test Strobe Messages ..................................54
Maximum Trouble Messages........................................53
Maximum Users............................................................70
Medium Depth..............................................................57
Medium pull algorithm .................................................23
Midnight Report ...........................................................32
Missed all Receivers.....................................................52
Misses...........................................................................52
modem ..........................................................................55
Modem Communications..............................................39
Modem Init .............................................................60, 63
Modem Port..................................................................58
Modem Reset................................................................60
Modified .......................................................................18
Modify Oper .................................................................18
Mon Power ...................................................................58
J
Jam Map .......................................................................51
Jamming..................................................................43, 51
Jamming Map ...............................................................47
Jamming of Receiver ....................................................41
K
Kill Transponder...........................................................19
Kill Transponder button................................................19
Known Transmitters .....................................................41
L
Last ...............................................................................35
Last MUX Message ......................................................49
Last Remote Access Time ............................................53
Learn address button .................................................66
LF Only.........................................................................59
Limit Alarms to 1 Transponder.....................................29
Linear algorithm ...........................................................23
Linear Depth.................................................................57
Load Delay ...................................................................48
Load Shedding..............................................................46
Local Database Drive .............................................26, 27
Local Escort Path .......................................................67
Local paging setup........................................................73
Locate ...........................................................................15
Locate ...........................................................................25
Locate Test Level .........................................................30
Locate Transmitters ......................................................13
Location........................................................................24
Estimate of................................................................11
Text to be displayed................................................24
Location Algorithm.......................................................23
Login Changes..............................................................39
Loop Communications..................................................47
low battery....................................................................69
Low Battery
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Index
EN | 82
Monitor Communications.............................................55
Monitored Periods ........................................................42
Multiple Map Files .......................................................72
Multiplex Point
Address, explanation of ............................................19
Removing from service.............................................44
Multiplex Receiver .............................................8, 10, 12
For automatic ID# capture........................................56
Multiplex Receiver Parameters.....................................20
MUX Bus Point Troubles.............................................41
Out Of Service Map......................................................44
Outgoing Failed Messages............................................46
Outgoing Retried Messages ..............................46, 53, 67
Output Device Error .....................................................41
Output includes Subscriber ID......................................29
Output includes Transmitter ID ....................................29
Output Verification.......................................................36
Overload Count.............................................................54
Overload Level .............................................................54
P
N
Page to individuals........................................................63
Pager.............................................................................40
Send Message ...........................................................63
Pager Communications.................................................55
Pager Group......................................................24, 62, 63
Pager Group..................................................................15
Pager ID........................................................................62
Pager ID........................................................................15
Pager Password.............................................................15
Pager Setup...................................................................73
Pager Text Manual........................................................63
Pages Per Call...............................................................62
paging modem setup .....................................................73
paging service...............................................................62
password.................................................................10, 13
Password.......................................................9, 56, 60, 62
Password Verify............................................................60
Paste.............................................................................25
Personal Transmitter.......................................................7
Automatic capture of ID# .........................................56
Disabled....................................................................12
Maintenance................................................................8
Security......................................................................7
Subscriber...................................................................7
Watchman category ..................................................11
Phone Book Edit Screen...............................................61
Phone Number ........................................................15, 62
Point..............................................................................52
Point In Service ............................................................44
Point Number................................................................20
Point Out Of Service.....................................................44
Point Transmitter ............................................................8
Point Troubles ..............................................................39
Point Type ..............................................................21, 22
Points, Reporting Alarm ...............................................38
Popup............................................................................40
Pop-up Trouble And Pager Delay.................................42
Pop-up Trouble Filter Screen........................................40
Power Loss
Network Comm Failure ................................................42
Network Communications ............................................39
Network Port ................................................................58
Network Status Screen..................................................52
New Alarm Reports ......................................................32
Next ................................................19, 35, 45, 47, 48, 49
No Buddy Check Delay................................................56
No CTS ........................................................................58
No Password on Reentry...............................................56
No Password Timeout...................................................56
No Password To Exit....................................................56
No Point Text If Area Text...........................................29
No Receiver Icons ........................................................29
No Response
From Multiplex Device.............................................41
No Restriction .............................................................38
Not Always Top Window.............................................56
Not Responding Map..............................................43, 47
Not Testing Report .......................................................32
Number
Area ..........................................................................20
Point..........................................................................20
O
Off ..........................................................................45, 51
Off (disarmed) ..............................................................35
On.................................................................................51
On (armed)....................................................................35
On Output Command....................................................45
On Outside Tests Flash Strobe For X Seconds.............30
Only From Transponder Selected .............................38
Open Loop Alarm.........................................................16
Open Loop Disable.......................................................16
Open Loop Trouble ......................................................16
Operator Activity Log...................................................38
Operator Database ........................................................14
Operator Database Changes..........................................38
Operator’s Response.....................................................11
Option 2........................................................................29
Option 4........................................................................29
Option 5........................................................................29
Optional Parameter.................................................47, 56
Optional Text................................................................16
Other Time....................................................................70
Out of Service Map.......................................................47
Alert Unit..................................................................41
Transponder..............................................................40
Preferences Changes.....................................................38
Previous..........................................19, 35, 45, 47, 48, 49
Print ..............................................................................32
Print ..............................................................................19
Print ..............................................................................64
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Index
EN | 83
Print ..............................................................................64
Print Report ..................................................................36
Print Report Now..........................................................32
Print System Reports Screen.........................................31
Print to File...................................................................64
Printer ...........................................................................37
Printer Output ...............................................................39
Pulse Dial......................................................................60
Put This Receiver In Setup Mode.................................49
Reset Point....................................................................51
Reset Status.......................................................53, 54, 68
Reset Transponder ........................................................44
Reset Transponder Troubles.........................................47
Restarted.......................................................................43
Restore..........................................................................27
Restore save old database message box........................28
Restore Screen..............................................................27
Restore to Disk Cartridge Path .....................................67
Restore warning message box.......................................28
Revision........................................................................51
RF Micro Version.........................................................51
RF Point Troubles.........................................................38
Run Buddy Check.........................................................55
Run Silent .....................................................................47
Run Test........................................................................52
R
Radio ID .......................................................................18
RAM Counters..............................................................49
RAM EE Buss Fault .....................................................49
RAM EE Mstat Batt .....................................................49
RAM Point Info............................................................49
RAM Point Stat ............................................................49
RAM Point Trouble......................................................49
Recall Operator In X Seconds ......................................30
Receive Level Maps .....................................................38
Received signal strength ...............................................10
Checkbox for displaying...........................................55
Received Transmission Map.........................................43
Receiver..............................................................8, 10, 12
Configuration............................................................49
Receiver 1.....................................................................23
Receiver 2.....................................................................23
Receiver Buffer Max ..............................................53, 68
Receiver Configuration Screen.....................................49
Receiver floor level selection .......................................23
Receiver Parameters .....................................................20
Receiver Point Type .....................................................22
Receiver Sensitivity Adjust...........................................24
Receiver Test Screen ....................................................51
Receiver’s Response.....................................................10
Receivers Not Heard From Report ...............................32
Red Led - Strobe...........................................................51
Reed Switch..................................................................16
Refresh Data ...............................................47, 53, 54, 68
remote access................................................................61
Remote Computer.........................................................59
remote connection.........................................................61
Remote Connection Screen...........................................60
Remote Key Activation.................................................41
Remote Key Tamper.....................................................41
Remote Port Setup Screen ............................................58
Remote Setup Screen....................................................59
Remote System Control ................................................60
Remove.........................................................................34
Report
S
SA%..............................................................................24
Save ..............................................................................25
Save Changes Screen....................................................25
Save EE ........................................................................49
Scaling ..........................................................................67
Schedules......................................................................33
Security Alarms Silent ..................................................29
security pager................................................................63
Security Pager Setup.....................................................74
Security Preferences .....................................................28
Unauthorized Transmitters........................................11
Security Preferences Screen..........................................28
Security Transmitter ....................................................7
Select ............................................................................64
Select Point Screen .......................................................21
Send All Other Alarms..................................................63
Send Change.................................................................48
Send Installer Demo Alarms.........................................63
Send Page a Second Time, 2 Minute Delay..................63
Send Pager Message Screen .........................................63
Send Security................................................................63
Send Service .................................................................63
Send to Group...............................................................63
Send to Individual.........................................................63
Sensitivity Adjust..........................................................24
Serial Number...............................................................70
service pager.................................................................62
Service Pager Setup......................................................74
Setup menu ...................................................................37
Shift Reminder..............................................................30
Shorted Loop Alarm .....................................................16
Shorted Loop Disable ...................................................16
Shorted Loop Trouble...................................................16
Show all error pop-ups...............................................65
Show Areas.............................................................20, 22
Show connection pop-ups...........................................65
Show History ................................................................36
Show Maintenance Levels ............................................55
Show Map.....................................................................36
End of shift reminder for ..........................................30
Trouble, filtering.......................................................39
Report Database Changes.............................................38
Reports Database..........................................................14
Require Alarm Report...................................................29
Requires Check-in ........................................................17
Reset Max.....................................................................70
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Index
EN | 84
Show Personal Data....................................................29
Show Points..................................................................20
Show Test Levels..........................................................55
Show Tests On The Map ..............................................29
Slave Computer ............................................................59
Slave Computer Answers..............................................59
Slave Database Drive..............................................26, 27
Slave Database Path ...................................................67
Slave’s Network Listen Port .........................................66
Slave's Network Address ..............................................66
Software Overview .........................................................9
Software Version ..........................................................69
Sound Maintenance Alarm ...........................................55
Sound Unauthorized Alarms.........................................28
Spacing .........................................................................52
Spare.......................................................................44, 48
Spare 2..........................................................................38
Stop all Pages ...............................................................63
Stop Test and Reset Counters.......................................52
Stress test......................................................................46
Strobe – Red Led..........................................................45
Strobe – Red Led Map..................................................43
Strong Depth.................................................................58
Strong pull algorithm....................................................23
Subscriber Check-in Report..........................................32
Subscriber Database .....................................................14
Subscriber Database Changes.......................................38
Subscriber Image Extension .........................................67
Subscriber Image File Path...........................................67
Subscriber Image Scaling .............................................67
Subscriber Images.........................................................72
Subscriber Transmitter....................................................7
Subsriber Database .......................................................76
Successful Incoming Messages.........................46, 52, 67
Successful Pager Messages...........................................53
Sunday Report ..............................................................32
Supervision Monitor.....................................................38
Supervision Monitors....................................................54
Synchronize System Time ............................................36
System defaults Screen .................................................31
System ID .....................................................................62
System Labels Screen ...................................................31
System Name..........................................................62, 63
System Operation..........................................................10
System Overview............................................................7
System Phone................................................................63
System Preferences
Tamper Map .................................................................47
Test.........................................................................23, 55
Sequence of occurrences during ............................12
Test Differential............................................................48
Test Min Level..............................................................48
Test On This MUX Point Successful............................50
Test Receiver................................................................48
Test Time......................................................................70
Test Transmitter Type...................................................48
Tests Including Point Info.............................................38
Tests, Single Line .........................................................38
This schedule defines the check-in times......................33
Tick Passes Hour ..........................................................70
Tick Time .....................................................................69
tone dialing ...................................................................60
Total Alarms Received .................................................45
Total Disk Space...........................................................69
Total Outgoing Messages .................................46, 53, 67
Total Remote Access Connections ...............................53
Total Tests Received ....................................................45
Total Transmissions......................................................52
Total Troubles Processed .............................................45
Total Troubles Shed .....................................................46
Total Wrong Access Code Attempts.............................53
Transmit........................................................................51
Transmit Buffer Max ..............................................53, 68
Transmit Delay .............................................................48
Transmit Point ..............................................................48
Transmitter
Point............................................................................8
Transmitter .................................................................10
Transmitter....................................................................12
Transmitter
Location....................................................................13
Transmitter Low Battery...............................................38
Transmitting Point ........................................................52
Transponder..........................................18, 38, 45, 48, 52
Communications Screen ...........................................42
Database ...................................................................17
Creating new entry................................................19
Function of..................................................................9
Identification Number ............................................18
Removing from Database..........................................19
Troubles....................................................................40
Transponder Area .........................................................17
Transponder Comm Port Setup.....................................18
Transponder Comm Port Setup Screen.........................58
Transponder Communication........................................38
Transponder Communications Screen ..........................42
Transponder Current Status Screen ..............................45
Transponder Data Collection And Response..........10, 12
Transponder Data View................................................39
Transponder Data View Screen ....................................48
Transponder Database Changes................................38
Transponder ID ..........................................................18
Transponder Maps........................................................38
Transponder Name .......................................................16
Setting......................................................................54
System Preferences Screen ...........................................54
System Serial ................................................................58
System Serial Port.........................................................37
System Status Screen....................................................53
T
Tamper....................................................................41, 43
Transponder..............................................................41
Tamper Load ................................................................48
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Escort | Technical Reference Manual | Index
EN | 85
Transponder Outputs ....................................................44
Transponder Parameter Change Screen........................47
V
Verbose Point Reports..................................................48
Verify Password............................................................62
Video Switcher .............................................................24
Video Switcher Control ................................................60
Video Switcher Restore ................................................60
View Alarm Groups......................................................34
View Alarm Groups......................................................33
virtual fence ..................................................................28
virtual fence alarm ........................................................16
Virtual Fence Alarm .....................................................25
Virtual Fence Area........................................................25
virtual receiver..............................................................23
Virtual Receiver Point Type .........................................22
Transponder Scanning ..................................................10
Transponder Startup .....................................................41
Transponder Troubles...................................................39
Trouble .........................................................................56
Current device status.................................................46
Emergency contact text box for ................................31
Trouble on Open Loop .................................................16
Trouble on Shorted Loop..............................................16
Trouble Response Text.................................................20
Trouble Tamper Text....................................................20
Trouble Type Text........................................................20
Troubles........................................................................62
Turn On Alarm Strobes ................................................28
Turn On Outside Sounders ...........................................28
W
Weekly Maintenance Test Report.................................32
Weekly Security Test Report........................................32
Weekly Subscriber Test Report ....................................32
Weekly Watchman Test Report....................................32
Wondering Alarm.........................................................25
Workstation Computer..................................................59
U
Uninstalling the Security Escort program.....................13
Unknown Transmitters..................................................41
Unlimited Retries..........................................................45
Uses Proxim Radio .......................................................48
Utilities Menu...............................................................26
Bosch Security Systems | 6/12 | 38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems
130 Perinton Parkway
Fairport, NY 14450-9199
Customer Service: (800) 289-0096
Technical Support: (888) 886-6189
© 2003 Bosch Security Systems
38947D
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Belkin Network Router F5D7233 User Manual
Bodum Food Processor 11038 User Manual
Bosch Power Tools Saw CS20 User Manual
Bose Home Theater System AM312515 Rev03 User Manual
Briggs Stratton Pressure Washer 020274 1 User Manual
Brother DVR DVR N4 User Manual
Brother Printer FAX 8250P User Manual
Bryant Furnace 396JAZ User Manual
Carrier DVD Player 50TCA04 A07 User Manual
Casablanca Fan Company Outdoor Ceiling Fan 6643050 User Manual