PCM2000
Configuration Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION I: APPLICATION CONFIGURATIONS
SETUP FOR CONFIGURATION 1: PAGE PORT CONTACT CLOSURE - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 1:
PAGE PORT CONTACT CLOSURE - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
In this configuration, the PCM unit responds to a contact closure on pins 2 & 5 of the TEL LINE jack on the PCMTIM module shorting the
+5V source to its ground.When the closure is removed, the page ends.Audio is provided to the system through a separate pair of leads on
pins 3 & 4 of the TEL LINE jack on the PCMTIM module. Pins 1 & 6 are not used in this configuration.
Note:The audio pair (page port) must pass DTMF in order to select a zone.
The required setup includes PCMTIM - PCMCPU - PCMZPM - PCMPS2. Modules must be assembled, from left to right, in this order.
INSTALLATION:
STEP 1:Assembling Modules PCMTIM to PCMCPU and to PCMZPM (see Illustration on page 38)
•
Plug the 6-pin power connector from the PCMCPU module to the PCMTIM module jack (J2). Be sure that the locking ridge faces head-
er wall. (Green wire to the top.)
•
Plug the 26-pin ribbon cable from the PCMCPU module to the PCMTIM module 26-pin connector (J1). Be sure to align the polarizing
tab in slot. (Pin 1 red stripe to the top.)
•
•
Place the modules together and dress the connector cables away from the sheet metal so they will not get pinched.
Push the two units together while aligning the locking tabs in the PCMTIM module to the locking slots in the PCMCPU module. Slide
the two units until the faces of both units are even.
•
•
Secure the two units together by tightening a screw into the screw clamp tab in the back of the PCMTIM.
Follow the same steps to add the PCMZPM module.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: Connecting Paging Port/Contact Closure from theTelephone System to the PCMTIM Module
•
Take the page port audio pair from the telephone system and wire it to the RJ11 TEL-LINE jack to pins 3 & 4 (red and green); and the
contact closure pair to pins 2 & 5 (black and yellow).
•
Use a 4- or 6-pin modular cord to connect the RJ11 to the TEL-LINE input on the PCMTIM module.
STEP 3: Switch Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module for Page Port Contact Closure configuration: switches 2, 3 & 7 ON (to the
right) and switches 1, 4, 5 & 6 OFF (to the left).
•
•
•
•
Set the SYS-ID DIP switches on the PCMCPU module to the OFF position (to the left).
Set the RUN-PROGRAM switch on the PCMCPU module to the RUN mode (up).
Set the Talk Back DIP switches on the PCMZPM module to the OFF position (to the left) for all zones.
Set the OUTPUT switch on the PCMZPM module to the HI-PWR position (down).
STEP 4: Testing your System
•
Connect power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw ter-
minals observing polarity.
•
•
•
•
At this point all the power LEDs should be lit on each module.
Access the page port from the phone system and verify access tones (double beep) in handset.
At this point, the system should be functioning properly.
Disconnect Power Supply.
STEP 5: Connecting the Paging Amplifier
•
Locate the terminals on the PCMCPU module labeled PA IN/RT and wire to the TIP and Ring (T & R) input on the Bogen paging amplifi-
er (either TPU-Series, GS-Series or Classic Series.)
•
Locate the terminals on the PCMCPU module labeled PA OUT/RT and wire to COMMON and either the 25 or 70V output on the
paging amplifier.
STEP 6: Connecting 25/70V AC Speakers
•
Locate the terminals on the PCMZPM module labeled ZONE A.These terminals have two connections marked + and -.Wire your
speakers for ZONE ONE to these terminals. Observe polarity (-) to common (+) to selected tap setting.
•
Follow the same procedure for the terminals labeled ZONE B for ZONE TWO, and the terminals labeled ZONE C for ZONE THREE.
STEP 7: Testing your System
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals, observing polarity.
•
•
•
•
Connect the Bogen amplifier to the AC power outlet (120V AC, 60Hz).
Set the volume on your Bogen amplifier to a 1/2 turn.
Access the paging from the telephone system and listen (on the handset) for the confirmation tone (double beep).
Dial 01 to access ZONE ONE and listen (on the handset and also to the speakers) for a pre-announce tone (single beep) followed by
your page (audio).
•
•
Follow the same steps for ZONES TWO (02) and THREE (03).
Set the Bogen amplifier to the desired volume level.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 2: PAGE PORTVOX CIRCUIT - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 2:
PAGE PORTVOX CIRCUIT - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
This configuration is for Page Ports without Contact Closures.A dry audio pair connected to pins 3 & 4 of the TEL LINE jack on the
PCMTIM module is used to detect audio and activate the system. Paging ends when theVOX timer or default timer times out. Pins 1, 2, 5 &
6 are not used in this configuration.
Note:The audio pair (page port) must pass DTMF in order to select a zone.
The required setup includes: PCMTIM - PCMCPU - PCMZPM - PCMPS2. Modules must be assembled, from left to right, in this order.
INSTALLATION:
STEP 1: Assembling Modules PCMTIM to PCMCPU and to PCMZPM
•
Follow the same procedure described previously on page 5, step 1.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: Connecting Paging Port/VOX from theTelephone System to the PCMTIM Module
•
Take the page port (VOX) audio pair from the telephone system and wire it to the RJ11 TEL-LINE jack in the PCMTIM module to pins
3 & 4 (red and green).
•
Use a 4- or 6-pin modular cord to connect the RJ11 to the TEL-LINE input on the PCMTIM module.
STEP 3: Switch Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module for Page PortVOX configuration: switches 1 & 7 ON (to the right) and
switches 2, 3, 4, 5 & 6 OFF (to the left).
•
•
•
•
Set the SYS-ID DIP switches on the PCMCPU module to the OFF position (to the left).
Set the RUN-PROGRAM switch on the PCMCPU module to the RUN mode (up).
Set the Talk Back DIP switches on the PCMZPM module to the OFF position (to the left) for all zones.
Set the OUTPUT switch on the PCMZPM module to the HI-PWR position (down).
STEP 4: Testing your System
Follow the same procedure described previously on page 5, step 4.
STEP 5: Connecting the Paging Amplifier
Follow the same procedure described previously on page 5, step 5.
STEP 6: Connecting 25/70V AC Speakers
Follow the same procedure described previously on page 5, step 6.
STEP 7: Testing your System
•
•
•
•
Follow the same procedure described previously on page 5, step 7.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 3: LOOP STARTTRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 3:
LOOP START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
In this configuration, the PCM unit supplies a 48V talk battery and loop current detection from pins 3 & 4 of the TEL LINE jack on the
PCMTIM module to the loop start trunk in the telephone system.There are two modes of operation for loop start trunk.
(1) When the unit detects a loop resistance between TIP and RING, it activates.When the loop opens, the page ends. Pins 1, 2, 5 & 6 are not
used in this configuration. Note: Default andVOX timers are not used in this mode.
(2) The unit will operate as in mode one, except it will also provide a one-second hook flash after the expiration of theVOX and/or Default
timers. Operation in this mode will enable the unit to automatically disconnect itself from the loop start trunk of the PBX.This will prevent
the paging system from being locked up indefinitely in the event a telephone is accidentally left off hook after a page has been completed.The
feature codes are 014 to inhibit and 015 to enable this feature.The default feature code is 014 (OFF).
The required setup includes PCMTIM - PCMCPU - PCMZPM - PCMPS2. Modules must be assembled, from left to right, in this order.
INSTALLATION:
STEP 1: Assembling Modules PCMTIM to PCMCPU and to PCMZPM
•
Follow the same procedure described previously on page 5, step 1.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: Connecting Loop StartTrunk from theTelephone System to the PCMTIM Module
•
Take the loop start trunk pair from the telephone system and wire it to the RJ11 TEL-LINE jack in the PCMTIM module to pins 3 and 4
(red and green).
•
Use a 4 or 6-pin modular cord to connect the RJ11 to the TEL-LINE input on the PCMTIM module.
STEP 3: Switch Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module for Loop Start Trunk configuration: switches 3, 4 & 5 ON (to the right) and
switches 1, 2, 6 & 7 OFF (to the left).
•
•
•
•
Set the SYS-ID DIP switches on the PCMCPU module to the OFF position (to the left).
Set the RUN-PROGRAM switch on the PCMCPU module to the RUN mode (up).
Set the Talk Back DIP switches on the PCMZPM module to the OFF position (to the left) for all zones.
Set the OUTPUT switch on the PCMZPM module to the HI-PWR position (down).
STEP 4: Testing your System
•
Connect power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw ter-
minals observing polarity.
•
•
•
•
Power LEDs should be lit on each module.
Access the Loop Start Trunk from the phone system and verify access tones (double beep).
At this point, the system should be functioning properly.
Disconnect Power Supply.
STEP 5: Connecting the Paging Amplifier
Follow the same procedure described previously on page 5, step 5.
STEP 6: Connecting 25/70V AC Speakers
Follow the same procedure described previously on page 5, step 6.
STEP 7: Testing your System
•
•
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals observing polarity.
•
•
•
•
Connect the Bogen amplifier to the AC power outlet (120V AC 60Hz).
Set the volume on your Bogen amplifier to a 1/2 turn.
Access the Loop Start Trunk from the telephone system and listen (on the handset) for the confirmation tone (double beep).
Dial 01 to access ZONE ONE and listen (on the handset and also to the speakers) for a pre-announce tone (single beep) followed by
your page (audio)
•
•
Follow the same steps for ZONES TWO (02) and THREE (03).
Set the Bogen amplifier to the desired volume level.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 4: GROUND START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 4:
GROUND START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
In this configuration, the PCM unit supplies a 48V talk battery and loop current detection from pins 3 & 4 of the TEL LINE jack on the
PCMTIM module to the ground start trunk in the telephone system.There are two modes of operation for ground start trunk.
(1) When the ground start trunk grounds Ring, the unit responds by closing the connection to Tip, which completes the access procedure.
When the loop is opened, the page ends. Pins 1, 2, 5 & 6 are not used in this configuration. Note: Default andVOX timers are not used
in this mode.
(2) The unit will operate as in mode one, except it will also provide a one-second hook flash after the expiration of theVOX and/or Default
timers. Operation in this mode will enable the unit to automatically disconnect itself from the ground start trunk of the PBX.This will pre-
vent the paging system from being locked up indefinitely in the event a telephone is accidentally left off hook after a page has been complet-
ed.The feature codes are 014 to inhibit and 015 to enable this feature.The default feature code is 014 (OFF).
The required setup includes PCMTIM - PCMCPU - PCMZPM - PCMPS2. Modules must be assembled, from left to right, in this order.
INSTALLATION:
STEP 1: Assembling Modules PCMTIM to PCMCPU and to PCMZPM
•
Follow the same procedure described previously on page 5, step 1.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: Connecting the Ground StartTrunk from theTelephone System to the PCMTIM Module
•
Take the ground start trunk pair from the telephone system and wire it to the RJ11 TEL-LINE jack in the PCMTIM module to pins 3 and
4 (red and green).
•
•
Use a 4 or 6-pin modular cord to connect the RJ11 to the TEL-LINE input on the PCMTIM module.
Use a 24-gauge solid wire to connect the GND ST terminal on the PCMTIM module to the PBX ground.This is typically the AC ground
for the PBX system.
STEP 3: Switch Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module for Ground Start Trunk configuration: switches 2, 4 & 5 ON (to the right)
and switches 1, 3, 6 & 7 OFF (to the left).
•
•
•
•
Set the SYS-ID DIP switches on the PCMCPU module to the OFF position (to the left).
Set the RUN-PROGRAM switch on the PCMCPU module to the RUN mode (up).
Set the Talk Back DIP switches on the PCMZPM module to the OFF position (to the left) for all zones.
Set the OUTPUT switch on the PCMZPM module to the HI-PWR position (down).
STEP 4: Testing your System
•
Connect power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw ter-
minals observing polarity.
•
•
•
•
At this point all the power LEDs should be lit on each module.
Access the Ground Start Trunk from the phone system and verify access tones (double beep).
At this point, the system should be functioning properly.
Disconnect Power Supply.
STEP 5: Connecting the Paging Amplifier
Follow the same procedure described previously on page 5, step 5.
STEP 6: Connecting 25/70V AC Speakers
Follow the same procedure described previously on page 5, step 6.
STEP 7: Testing your System
•
•
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals observing polarity.
•
•
•
•
Connect the Bogen amplifier to the AC power outlet (120V AC 60Hz).
Set the volume on your Bogen amplifier to a 1/2 turn.
Access the Ground Start Trunk from the telephone system and listen (on the handset) for the confirmation tone (double beep).
Dial 01 to access ZONE ONE and listen (on the handset and also to the speakers) for a pre-announce tone (single beep) followed by
your page (audio).
•
•
Follow the same steps for ZONES TWO (02) and THREE (03).
Set the Bogen amplifier to the desired volume level.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 5: STATION LEVEL/CENTREX - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 5:
STATION LEVEL/CENTREX - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS
In this configuration, the PCM unit responds to a 90V AC 20Hz ringing signal in pins 3 & 4 of the TEL LINE jack on the PCMTIM module and
answers after the first full ring.As soon as it answers, the default timer is started.The default timer determines the maximum length of any
page.When a paging zone is selected, theVOX timer (if enabled) is started.ThisVOX timer repeatedly resets as long as audio is detected on
the line. If no audio is detected within theVOX time period, the page will end. If audio continues to be detected, the default timer will con-
trol the page length. Pins 1, 2, 5 & 6 are not used in this configuration.
Note: In this configuration, the unit will also respond to CPC pulses (interruption of loop current) disconnecting the line.
The required setup includes PCMTIM -PCMCPU - PCMZPM - PCMPS2. Modules must be assembled, from left to right, in this order.
INSTALLATION:
STEP 1: Assembling Modules PCMTIM to PCMCPU and to PCMZPM
•
Follow the same procedure described previously on page 5, step 1.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: Connecting the Station Level/Centrex from theTelephone System to the PCMTIM Module
•
Take the Station Level/Centrex pair from the telephone system and wire it to the RJ11 TEL-LINE jack in the PCMTIM module to pins 3
and 4 (red and green).
•
Use a 4 or 6-pin modular cord to connect the RJ11 to the TEL-LINE input on the PCMTIM module.
STEP 3: Switch Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module for Station Level/Centrex configuration: switch 6 ON (to the right) and
switches 1, 2, 3, 4, 5 & 7 OFF (to the left).
•
•
•
•
Set the SYS-ID DIP switches on the PCMCPU module to the OFF position (to the left).
Set the RUN-PROGRAM switch on the PCMCPU module to the RUN mode (up).
Set the Talk Back DIP switches on the PCMZPM module to the OFF position (to the left) for all zones.
Set the OUTPUT switch on the PCMZPM module to the HI-PWR position (down).
STEP 4: Testing your System
•
Connect power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw ter-
minals observing polarity.
•
•
•
•
At this point all the power LEDs should be lit on each module.
Access the Station Level/Centrex line from the phone system and verify access tones (double beep).
At this point, the system should be functioning properly.
Disconnect Power Supply.
STEP 5: Connecting the Paging Amplifier
Follow the same procedure described previously on page 5, step 5.
STEP 6: Connecting 25/70V AC Speakers
Follow the same procedure described previously on page 5, step 6.
STEP 7: Testing your System
•
•
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals observing polarity.
•
•
•
•
Connect the Bogen amplifier to the AC power outlet (120V AC 60Hz).
Set the volume on your Bogen amplifier to a 1/2 turn.
Access the Station Level/Centrex port from the telephone system and listen (on the handset) for the confirmation tone (double beep).
Dial 01 to access zone ONE and listen (on the handset and also to the speakers) for a pre-announce tone (single beep) followed by
your page (audio).
•
•
Follow the same steps for ZONES TWO (02) and THREE (03).
Set the Bogen amplifier to the desired volume level.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 6: EXTENDED PAGING SYSTEM
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 6:
EXTENDED PAGING SYSTEM
This illustration shows the wiring between a master assembly and a satellite assembly in a PCM system with a satellite assembly for one-way paging.
As described previously, the required setup for one-way basic configuration includes: PCMTIM, PCMCPU, PCMZPM, and the power supply
PCMPS2. For PCM systems with satellites (more than 9 zones), the number of modules and power supplies will increase as follows:
# ZONES
# PCMTIM
# PCMCPU
# PCMZPM*
# PCMPS2
1 to 9
1
1
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
1 to 3
4 to 6
7 to 9
1
2
3
4
5
6
7
8
9
10 to 18
19 to 27
28 to 36
37 to 45
46 to 54
55 to 63
64 to 72
73 to 81
82 to 90
91 to 99
10 to 12
13 to 15
16 to 18
19 to 21
22 to 24
25 to 27
28 to 30
31 to 33
10
11
10
11
Notice that for every 9 zones, one additional PCMCPU and one additional PCMPS2 are needed.
* 1 PCMZPM for every 1-3 paging zones.
INSTALLATION:
STEP 1: Assembling Master Modules PCMTIM to PCMCPU and to PCMZPM
•
Follow the same procedure described previously on page 5, step 1.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: Assembling Satellite Modules PCMCPU to PCMZPM (see Illustration on page 38)
•
Plug the 6-pin power connector from the PCMZPM module to the PCMCPU module jack (J2.) Be sure that the locking ridge faces the
header wall. (Green wire to the top).
•
Plug the 26-pin ribbon cable from the PCMZPM module to the PCMCPU module 26-pin connector (J1). Be sure to align the polarizing
tab in slot. (Pin 1 red stripe to the top).
•
•
The satellite systems are usually installed below the the master assembly and must be within 3 feet of each other.
Use an RCA cable to connect the PCMCPU modules from DATA LINK to DATA LINK RCA connectors. (See drawing.)
STEP 3: Switch Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module to match the paging output access from the telephone system based on the
type of telephone interface used. (See step 3 on page 5 if using Page Port Contact Closure; page 7 for Page PortVOX; page 9 for Loop
Start Trunk; page 11 for Ground Start Trunk; or page 13 for Station Level/Centrex.)
•
•
Set the SYS-ID DIP switches on the master PCMCPU module to the OFF position (to the left).
Set the SYS-ID DIP switches on the first satellite PCMCPU module to the following configuration: Switch 1 to the ON position (to the
right). Switches 2, 3, & 4 to the OFF position (to the left). See SYS-ID switch settings chart on page 38 for additional satellite systems.
Set the RUN-PROGRAM switch on the PCMCPU module to the RUN mode (up).
Set the TALK BACK switches on the PCMZPM modules to the OFF position (to the left) for all zones.
Set the OUTPUT switch on all the PCMZPM modules to the HI-PWR position (down).
•
•
•
STEP 4: Testing your System
•
Connect one PCMPS2 power supply to each PCMCPU module either by the power jack 12V DC input or wire it to the 12V DC screw
terminals, observing polarity.
•
•
•
•
At this point all the power LEDs should be lit on each module.
Access the paging from the phone system and verify access tones (double beep).
At this point, the system should be functioning properly.
Disconnect Power Supply.
STEP 5: Connecting the Paging Amplifier
•
Locate the terminals on both PCMCPU modules labeled PA OUT/RT and wire them to the COMMON and 25V or 70V output on the
Bogen paging amplifier (either TPU-Series, GS-Series or Classic Series).
•
Locate the terminals on the PCMCPU modules labeled PA IN/RT and wire to the TIP and RING input on the Bogen paging amplifier.At
this point, the amplifier is connected in parallel to the master PCMCPU module and the satellite PCMCPU module.
STEP 6: Connecting 25/70V AC Speakers
Follow the same procedure described previously on page 5, step 6.
STEP 7: Testing your System
•
•
Follow the same procedure described previously on page 5, step 7.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 7:TWO-WAY TALK BACK PAGING SYSTEM
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 7:
TWO-WAY TALK BACK PAGING SYSTEM
This configuration is essentially the same as the one-way paging system described previously.The main difference between the one-way con-
figuration and this configuration is that the centralized high-power amplifier is connected to the PCMTBM module instead of the PCMCPU
module.The required setup includes: PCMTIM - PCMCPU - PCMTBM - PCMZPM - PCMPS2. Modules must be assembled, from left to right,
in this order.
Notes: Talk Back is only available in High-Power Zones with 25/70V AC speakers.The paging access output from the tele-
phone system must support two-way communications.
INSTALLATION:
STEP 1: Assembling Modules PCMTIM to PCMCPU to PCMTBM and to PCMZPM (see Illustration on page 38)
•
Plug the 6-pin power connector from the PCMCPU module to the PCMTIM module jack (J2.) Make sure that the locking ridge faces
header wall. (Green wire to the top).
•
Plug the 26-pin ribbon cable from the PCMCPU module to the PCMTIM module 26-pin connector (J1). Make sure to align the polarizing
tab in slot. (Pin 1 red stripe to the top).
•
•
Place the modules together and dress the connector cables away from the sheet metal so they will not get pinched.
Push the two units together while aligning the locking tabs in the PCMTIM module to the locking slots in the PCMCPU module. Slide
the two units until the faces of both units are even.
•
•
Secure the two units together by tightening a screw into the screw clamp tab in the back of the unit.
Follow the same steps to add the PCMTBM module and the PCMZPM modules.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: ConnectingTelephone System Paging Output to the PCMTIM
•
Refer to paging access modes described previously in Step 2 on pages 5 (paging port/contact closure), 7 (paging port/VOX), 9 (loop start
trunk), 11 (ground start trunk), or 13 (station level/Centrex).
STEP 3: Switch Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module to match the paging output access from the telephone system based on the
type of telephone interface used. (See step 3 on page 5 if using Page Port Contact Closure; page 7 for Page PortVOX; page 9 for Loop
Start Trunk; page 11 for Ground Start Trunk; or page 13 for Station Level/Centrex.)
•
•
•
•
Set the SYS-ID DIP switches on the PCMCPU to the OFF position (to the left).
Set the RUN-PROGRAM switch on the PCMCPU to the RUN mode (up).
Set the TALK BACK switches for the zones requiring two-way talk back to the ON position (right) on the PCMZPM module.
Set the OUTPUT switch on the PCMZPM module to the HI-PWR position (down).
STEP 4: Testing your System
•
Connect power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw ter-
minals observing polarity.
•
•
•
At this point all the power LEDs should be lit on each module.
Access the paging from the phone system and verify access tones (double beep) in handset.
Speak into the handset and listen.You should be able to hear the Talk Back Relay clicking back and forth inside the PCMTBM module.
(You must be near the PCM unit to hear it.)
•
•
At this point, the system should be functioning properly.
Disconnect Power Supply.
STEP 5: Connecting the Paging Amplifier
•
Locate the terminals on the PCMTBM module labeled PA OUT/RT and wire to the COMMON and either 25 or 70V output on the
Bogen paging amplifier (either TPU-Series, GS-Series or Classic Series).
•
Locate the terminals on the PCMTBM module labeled PA IN/RT and wire to the TIP and RING input on the Bogen paging amplifier.
STEP 6: Connecting 25/70V AC Speakers
Follow the same procedure described previously on page 5, step 6.
STEP 7: Testing your System
•
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals observing polarity.
•
•
•
•
Connect the Bogen amplifier to the AC power outlet (120V AC 60Hz).
Set the volume on your Bogen amplifier to a 1/2 turn.
Access the paging from the telephone system and listen (on the handset) for the confirmation tone (double beep).
Dial 01 to access ZONE ONE and listen (on the handset and also to the speakers) for a pre-announce tone (single beep).At this point
you should be able to hear audio from the location where the speaker for ZONE ONE is installed.
The volume and delay controls on the PCMTBM module control the audio back into the handset.Adjust these controls for best opera-
tion.
•
•
Set the Bogen amplifier to the desired volume level.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 8:TWO-WAY TALK BACK EXTENDED PAGING SYSTEM
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 8:
TWO-WAY TALK BACK EXTENDED PAGING SYSTEM
This configuration is essentially the same as the two-way paging system described previously on page 17.The main difference is the addition
of a satellite assembly.
The required setup includes: PCMTIM - 2 PCMCPU - PCMTBM - 4 PCMZPM - 2 PCMPS2
Note: Talk Back is only available in High-Power Zones with 25/70V AC speakers.
The paging access output from the telephone system must support two-way communications.
INSTALLATION:
STEP 1: Assembling Master Modules PCMTIM to PCMCPU to PCMTBM and to PCMZPM
•
Follow the same procedure described previously on page 17, step 1.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: Assembling Satellite Modules PCMCPU to PCMZPM
Follow the same procedure described previously on page 15, step 2.
STEP 3: Switch Settings
•
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module to match the paging output access from the telephone system based on the
type of telephone interface used. (See step 3 on page 5 if using Page Port Contact Closure; page 7 for Page PortVOX; page 9 for Loop
Start Trunk; page 11 for Ground Start Trunk; or page 13 for Station Level/Centrex.)
•
•
Set the SYS-ID DIP switches on the master PCMCPU module to the OFF position (to the left).
Set the SYS-ID DIP switches on the first satellite PCMCPU module to the following configuration: switch 1 to the ON position (to the
right), switches 2, 3, & 4 to the OFF position (to the left). See additional SYS-ID settings on page 38.
Set the RUN-PROGRAM switch on each PCMCPU to the RUN mode (up).
Set the TALK BACK switches on the PCMZPM modules to the ON position (to the right) for all zones.
Set the OUTPUT switch on each PCMZPM module to the HI-PWR position (down).
•
•
•
STEP 4: Testing your System
•
Connect one PCMPS2 power supply to each PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals, observing polarity.
•
•
•
•
At this point all the power LEDs should be lit on each module.
Access the paging from the phone system and verify access tones (double beep).
At this point, the system should be functioning properly.
Disconnect Power Supply.
STEP 5: Connecting the Paging Amplifier
•
Locate the terminals on the PCMTBM module labeled PA OUT/RT and wire to the COMMON and either 25 or 70V output on the
Bogen paging amplifier (either TPU-Series, GS-Series or Classic Series).
•
Locate the terminals on the PCMTBM module labeled PA IN/RT and wire to the TIP and RING input on the Bogen paging amplifier.
STEP 6: Connecting 25/70V AC Speakers
Follow the same procedure described previously on page 5, step 6.
STEP 7: Testing your System
•
•
Connect a PCMPS2 power supply to each PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals observing polarity.
•
•
•
•
Connect the Bogen amplifier to the AC power outlet (120V AC 60Hz).
Set the volume on your Bogen amplifier to a 1/2 turn.
Access the paging from the telephone system and listen (on the handset) for the confirmation tone (double beep).
Dial 01 to access ZONE ONE and listen (on the handset and also to the speakers) for a pre-announce tone (single beep).At this point,
you should be able to hear audio from the location where the speaker for ZONE ONE is installed.
The volume and delay controls on the PCMTBM module, control the audio back into the handset.Adjust these controls for best opera-
tion.
•
•
Set the Bogen amplifier to the desired volume level.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 9: 3-ZONE - ONE-WAY PAGING - LOW-POWER SYSTEM - DEDICATED AMPLIFIERS OR SELF-AMPLIFIED SPEAKERS
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 9:
3-ZONE - ONE-WAY PAGING - LOW-POWER SYSTEM - DEDICATED AMPLIFIERS OR SELF-AMPLIFIED SPEAKERS
Low-Power System is a switch-selectable feature that allows the system designer to use dedicated amplifiers or self-amplified speakers on the
zone outputs.The PCMZPM module that is to be used as a low-power module will switch only low-level signals to the zone outputs for use
with dedicated amplifiers or self-amplified speakers. Note that its output switch is set to LO PWR. In this example, three TPU100B amplifiers
are used but amplified speakers can be substituted.
Note: Low-Power Systems do not support two-way paging.
INSTALLATION:
STEP 1: Assembling Modules
•
Follow the same procedure described previously on page 5, step 1.
Note: Do NOT connect the PCMPS2 (power supply) at this point.
STEP 2: ConnectingTelephone System Paging Output to the PCMTIM
•
Refer to paging access modes described previously in Step 2 on pages 5 (paging port/contact closure), 7 (paging port/VOX), 9 (loop start
trunk), 11 (ground start trunk), or 13 (station level/Centrex).
STEP 3: Switch Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module to match the paging output access from the telephone system based on the
type of telephone interface used. (See step 3 on page 5 if using Page Port Contact Closure; page 7 for Page PortVOX; page 9 for Loop
Start Trunk; page 11 for Ground Start Trunk; or page 13 for Station Level/Centrex.)
•
•
•
Set the SYS-ID switches on the PCMCPU to the OFF position (to the left).
Set the TALKBACK switches on the PCMZPM to the OFF position (to the left) for all zones.
Set the LO PWR / HI PWR OUTPUT switch on the PCMZPM to the LO PWR position (up).
STEP 4: Connecting the Paging Amplifiers
•
Locate the terminals on the PCMZPM module labeled ZONE A and connect to the TIP and RING terminals of the amplifier(s) for
ZONE A.
•
Follow the same procedure for ZONE B and ZONE C.
STEP 5: Connecting Self-Amplified Speakers
Locate the terminals on the amplifiers labeled COM and 25V or 70V AC and connect the speakers related to that particular zone.
STEP 6: TestingYour System
•
•
Follow the same procedure described previously on page 5, step 7.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 10: 6 ZONES - ONE-WAY PAGING - MIXED HIGH- AND LOW-POWER ZONES -
25/70V AC OR SELF-AMPLIFIED SPEAKERS
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 10:
6 ZONES - ONE-WAY PAGING - MIXED HIGH- AND LOW-POWER ZONES -
25/70V AC OR SELF-AMPLIFIED SPEAKERS
High- and Low-Power Mixed System is a non-programmable feature that lets the system designer use a dedicated amplifier or self-amplified
speaker per zone and at the same time use a centralized amplifier for zones requiring less than 250 watts of power*.The PCMZPM module
to be used as a low-power module must have all three zones with dedicated amplifiers or self-amplified speakers and have its output switch
set to Low-Power.The other PCMZPM module will be used as a high-power module and its output switch must be set to High-Power. In this
example, three TPU100B amplifiers are used on the second PCMZPM low-power module.
Note: Low-Power Systems do not support two-way paging.
INSTALLATION:
STEP 1: Assembling Modules
•
Follow the same procedure described previously on page 5, step 1.
Note: Do NOT connect PCMPS2 (power supply) at this point.
STEP 2: ConnectingTelephone System Paging Output to the PCMTIM
•
Refer to paging access modes described previously in Step 2 on pages 5 (paging port/contact closure), 7 (paging port/VOX), 9 (loop start
trunk), 11 (ground start trunk), or 13 (station level/Centrex).
STEP 3: Switch and Control Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module to match the paging output access from the telephone system based on the
type of telephone interface used. (See step 3 on page 5 if using Page Port Contact Closure; page 7 for Page PortVOX; page 9 for Loop
Start Trunk; page 11 for Ground Start Trunk; or page 13 for Station Level/Centrex.)
•
•
•
•
Set the SYS ID switches on the PCMCPU module to the OFF position (to the left).
Set the TALK BACK switches on the PCMZPM module to the OFF position (to the left) for all zones.
Set the LO PWR / HI PWR OUTPUT switch on the first PCMZPM High-Power module to the HI PWR OUTPUT position (down).
Set the LO PWR / HI PWR OUTPUT switch on the second PCMZPM Low-Power module to the LO PWR OUTPUT position (up).
STEP 4: Connecting Amplifiers
•
•
Locate the terminals on the PCMCPU module labeled PA IN/RT and wire it to the TIP and RING (T & R) input on the amplifier.
Locate the terminals on the PCMCPU module labeled PA OUT/RT and wire it to the COMMON and either 25 or 70V AC output on
the amplifier.
•
Locate the terminals on the second PCMZPM module Low-Power module labeled ZONE A and connect the amplifier to the TIP and
RING terminals. Follow the same procedure for ZONE B and ZONE C.
STEP 5: Connecting 25/70V AC Speakers
Follow the same procedure described previously on page 5, step 6.
STEP 6: TestingYour System
•
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals observing polarity.
•
•
•
•
Connect the Bogen amplifiers to the AC power outlet (120V AC 60Hz).
Set the volume on your Bogen amplifiers to a 1/2 turn.
Access the Paging from the telephone system and listen (on the handset) for the confirmation tone (double beep).
Dial 01 to access ZONE ONE and listen (on the handset and also to the speakers) for a pre-announce tone (single beep) followed by
your page (audio).
•
•
Follow the same steps for ZONES TWO (02) through SIX (06).
Set the Bogen amplifiers to the desired volume level.
* Older PCM systems only have a 150W capacity.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 11: MICROPHONE OVERRIDE
B L
W
Y
B K
G
R
24
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 11:
MICROPHONE OVERRIDE
Microphone Override is a feature that lets the system designer take priority over all paging functions and make a system-wide page to all
speakers.
In addition to the PCM modules, setup requires a BogenVAR1 (voice-activated relay), PRS40C (12V DC power supply) and an MBS1000 or
DDU250 (desktop microphone).
The Override feature includes a quad beep pre-announce tone which can be enabled or inhibited.
INSTALLATION:
STEP 1: Assembling Modules and Connecting the Amplifier
•
Refer to step 1 on pages 5 and 17.
STEP 2: Connecting the Paging Amplifier
Follow the same procedure described previously on page 5 or 17, step 5.
STEP 3: Connecting Optional Equipment
•
•
•
Attach a 6-pin RJ11 modular jack to the wall next to the PCM2000 unit.
Connect the first audio output terminal from the top of theVAR1 (right screw terminals) to the RJ11 modular jack terminalY (yellow).
Connect the second audio output terminal from the top of theVAR1 to the N.O. contact of theVAR1.
Connect the fifth screw terminal from the top of theVAR1 (see drawing) to the RJ11 modular jack terminal BK (black).
Connect the relay terminals (normally open contacts) from theVAR1 (two bottom right screw terminals) to the RJ11 modular jack ter-
minals W (white) and BL (blue).
•
•
•
•
•
•
Connect the MBS1000 or DDU250 microphone leads to theVAR1 (left screw terminals): red to third screw, black to fifth screw, and
shield to fourth screw.
Do not use the white and green wires from the MBS1000 or DDU250 unless you want to use them instead of the normally open con-
tacts on theVAR1.
Connect a 6-pin RJ11 modular cable between the RJ11 modular jack (previously attached to the wall next to the PCM2000) and the
Override RJ11 input on the PCMTIM module.
Connect the PRS40C power supply to theVAR1 (two top left screw terminals) observing polarity or use the mini-plug and connect it
into the mini-jack at the bottom.
STEP 4: Switch and Control Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module to match the paging output access from the telephone system based on the
type of telephone interface used. (See step 3 on page 5 if using Page Port Contact Closure; page 7 for Page PortVOX; page 9 for Loop
Start Trunk; page 11 for Ground Start Trunk; or page 13 for Station Level/Centrex.)
•
•
Set the Line/MIC switch on theVAR1 to the MIC position.
Set the Mic volume control on theVAR1 at 50%.
STEP 5: TestingYour System
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals observing polarity.
•
•
•
•
Connect the Bogen amplifier to the AC power outlet (120V AC 60Hz).
Set the volume on your Bogen amplifier a half turn.
Access the paging from the telephone system and listen (on the handset) for the confirmation tone (double beep).
Dial 01 to access ZONE ONE and listen (on the handset and also to the speakers) for a pre-announce tone (single beep) followed by
your page (audio).
•
•
•
•
Follow the same steps for ZONES TWO (02) and THREE (03).
Access the emergency override by pressing the talk bar on the MBS1000 or sliding the DDU250 switch.
You should hear a quad beep pre-announce tone followed by your all-call/emergency page.
Adjust theVAR1 and PCM2000 controls for optimal operation.
NOTE: You will not be able to access individual zones using the Override feature, it is for All-Call Emergency only to all
zones.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 12: DFT120 &TAMB WIRING DIAGRAM - LOOP START TRUNK, GROUND START TRUNK OR STATION LEVEL
B L
W
Y
B K
G
R
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 12:
DFT120 &TAMB WIRING DIAGRAM - LOOP STARTTRUNK, GROUND STARTTRUNK, OR STATION LEVEL
In this configuration, the telephone output is connected to the Bogen Telephone Access Module model TAMB; the TAMB module is connected
to the Bogen Digital Feedback Terminator model DFT120; and the DFT120 is connected to the PCM2000 system. The TAMB module is acti-
vated by the telephone system and, at the same time, the DFT120 is activated by the TAMB’s normally open contacts. Using digital technolo-
gy, the DFT120 stores the DTMF tones and the paging audio.When the TAMB closed contacts are removed from the DFT120, the DFT120
activates the PCM2000 system also using normally open contacts, and plays the page (audio). In addition to the above equipment, you will
also need a PRSASAC power supply and two RJ11 modular boxes.
INSTALLATION:
STEP 1: Assembling Modules and Connecting the Amplifier
•
Refer to step 1 on pages 5 and 17.
STEP 2: Connecting the Paging Amplifier
Follow the same procedure described previously on page 5 or 17, step 5.
STEP 3: Connecting an Analog Line or Ground StartTrunk from theTelephone System to theTAMB
Take the Analog Line or Ground Start trunk pair from the telephone system and wire it to the TAMB terminals T & R.
STEP 4: Connecting theTAMB Module to the DFT120
•
•
•
Using a 6-pin RJ11 modular jack, connect terminals labeled PT & PR from the TAMB to the modular jack terminals R (red) and G
(green).
•
•
Connect terminals labeled N.O. & COM from the TAMB to the modular jack terminalsY (yellow) and BK (black).
Connect a 6-pin RJ11 modular cable from the RJ11 jack to the AUDIO IN jacks on the DFT120. Place the switch labeled DL/LS to the
DL (Dry Loop) position.
•
•
Connect terminals labeled +24/48 & -24/48 from the TAMB to the PRSASAC power supply. Use pins 1 & 2 labeled 24V DC / 450 mA.
Connect the DFT120 power supply (supplied with the unit) to the DFT120.
STEP 5: Connecting the DFT120 to the PCMTIM Module
•
•
•
Attach a 6-pin RJ11 modular jack to the wall next to the PCM2000 unit.
Connect terminals 3 & 4 from the DFT120 jack labeled AUDIO OUT, to the RJ11 modular jack terminals R (red) and G (green).
Connect terminals 2 & 5 from the DFT120 jack labeled AUDIO OUT (PLAY contact) to the RJ11 modular jack terminalsY (yellow) and
BK (black).
•
Connect a 6-pin RJ11 modular cable between the RJ11 modular jack and the TEL LINE RJ11 input on the PCMTIM module.
STEP 6: Switch and Control Settings
•
•
Set the switches 1, 2 & 4 to ON (to the right) and 3 & 5 to OFF (to the left) on the TAMB.
Set the switches 2, 3, & 7 to ON (to the right) and 1, 4, 5 & 6 to OFF (to the left) on the PCMTIM module for Paging Port Contact clo-
sure operation.
STEP 7: TestingYour System
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals observing polarity.
•
•
•
•
Connect the PCMPS2, PRSASAC, and the DFT120 power supplies and the amplifier to the AC power outlet 120V AC 60Hz.
Set the volume on your Bogen amplifier to a half turn.
Adjust the DFT120 AUDIO OUT volume control to 50%. (You may need to readjust this control higher or lower later, after the test.)
Access the paging from the telephone system.The RECORD LED on the DFT120 must be lit showing that the DFT120 is already
recording.
•
•
•
Dial 01 to record ZONE ONE DTMF tone followed by a test page. (Notice that you will not hear audio coming from the speakers at
this point.)
Hang-up the handset.The PLAY LED on the DFT120 must light showing that the DFT120 is playing the page and you must be able to
hear the page.
If the page is too low, adjust the control for optimal operation.
Note: Unlike the previous Digital FeedbackTerminator (DFT30), the DFT120 will accept a Loop StartTrunk or Page Port
directly connected to the unit.Therefore, when connecting to a Loop StartTrunk, aTAMB is not required. (See DFT120
manual for complete instructions.)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 13: EMERGENCY VOICE ANNOUNCEMENT OVERRIDE
B L
W
Y
B K
G
R
28
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 13:
EMERGENCY VOICE ANNOUNCEMENT OVERRIDE
Voice Announcement Override is a non-programmable feature that lets the caller take priority over all paging functions and make a system-
wide emergency voice announcement page to all speakers. In addition to the PCM modules, this option requires a ProHold (digital announc-
er) and a normally open momentary switch supplied by the user.
The Override feature includes a quad beep pre-announce tone which can be enabled or inhibited through programming.
INSTALLATION:
STEP 1: Assembling Modules and Connecting the Amplifier
•
Refer to step 1 on pages 5 and 17.
STEP 2: Connecting the Paging Amplifier
Follow the same procedure described previously on page 5 or 17, step 5.
STEP 3: Connecting Optional Equipment
•
•
•
Attach a 6-pin RJ11 modular jack to the wall next to the PCM2000 unit.
Connect the audio output from the ProHold labeled Line 600 using the supplied RCA cable to the RJ11 modular jack terminalsY (yel-
low) and BK (black).
•
•
•
Using the supplied stereo mini-plug, connect it to the TRIG input connector of the ProHold Digital Announcer. At the end of this cable,
you will see 3 bare wires labeled TIP, BARREL and RING.
Connect the TIP wire to one of the terminals on the normally open connections of the customer-supplied switch and the other switch
terminal to the RJ11 modular jack terminal BL (blue).
Connect the BARREL wire to the RJ11 modular jack terminal BL (blue). At this point you should have two wires connected to the BL
(blue) terminal.
•
•
Connect the RING wire to the RJ11 modular jack terminal W (white).
Connect a 6-pin RJ11 modular cable between the RJ11 modular jack and the Override RJ11 input on the PCMTIM module.
STEP 4: Switch and Control Settings
•
Set the TEL-INT-SEL DIP switches on the PCMTIM module to match the paging output access from the telephone system based on the
type of telephone interface used. (See step 3 on page 5 if using Page Port Contact Closure; page 7 for Page PortVOX; page 9 for Loop
Start Trunk; page 11 for Ground Start Trunk; or page 13 for Station Level/Centrex.)
STEP 5: TestingYour System
•
Connect the power supply PCMPS2 to the PCMCPU module to either the power jack 12V DC input or wire it to the 12V DC screw
terminals, observing polarity.
•
•
•
•
Connect the Bogen amplifier to the AC power outlet (120V AC 60Hz).
Set the volume on your Bogen amplifier to a half turn.
Insert a pre-recorded normal bias audio tape into the ProHold cassette compartment.
Once the ProHold announcer has downloaded the audio and the LOAD light goes "OFF", press the normally open customer supplied
switch once and listen for the all-call announcement.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP FOR CONFIGURATION 14: DTMF MICROPHONE ZONE PAGING
SUHRE
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 14:
DTMF MICROPHONE ZONE PAGING
This section will describe the configuration for the use of a Shure microphone Model 885TT with DTMF dialing capabilities and the MODULINK five-
conductor coil-cord model ALM-1.
In addition to the PCM2000 system and associated amplifiers, the model numbers and components required for this configuration are:
1- Shure Microphone model 885TT
1- Shure MODULINK coil cord model ALM-1
1- XLR connector
1- 680 ohms ¼-watt resistor
Paging with a DTMF Shure condenser microphone is a non-programmable feature that lets the caller use a Shure 885TT microphone to page
one-way to specific zones or all zones.
Note:The Shure microphone model 885TT requires a modification in order to operate properly with the PCM2000 zone
paging modules.
SHURE 885TT MODIFICATION:
STEP 1: Disassembling the Microphone
•
•
•
Remove the cable, if attached, to the microphone using a paper clip.
Remove the four Phillips-head screws from the back of the microphone.
Hold the microphone with its back toward you and the cable connector down, and carefully separate the case back slightly from the
front.
•
Pivot the case back to the right taking care not to damage any internal leads or components.
STEP 2: Detaching the Case Back and Rear Printed Circuit Board
•
•
•
With the partially disassembled microphone face down on a flat surface and with the cable entry toward you, locate the multi-pin con-
nector on the left side between the center board and the rear board.
Carefully pry the rear board away from the connector on the centerboard.You may need a small flathead screwdriver to separate the
terminal pins connected to the rear board and the connector attached to the center board.
Lift the microphone case back and the rear board away from the center board.
STEP 3: Modification
•
•
•
Locate pin 5 on the solder side of the J303 phone jack (cable entry) and cut the trace around pin 5, disconnecting it from ground.
Locate the black wire connected from the microphone switch to the first printed circuit board and unsolder it from the board.
Solder the black wire disconnected previously from the first P.C. board to pin 5 on the soldered side of the J303 phone jack (cable
entry).
•
Locate transistor Q303 on the component side and clip or unsolder the collector lead.
STEP 4: XLR Connector Setup
•
•
An XLR connector (not included) is recommended.
Solder the XLR connector to the Shure microphone coil cord MODULINK model ALM-1 as follows:
•
•
Solder a 680-ohm resistor across pins 1 and 2
Solder-shielded wire to pin 1, red and black wires to pin 2, and yellow to pin 3.
STEP 5: Reassembling
Reassemble the microphone by reversing the steps of disassembly.
OPERATION:
•
•
•
•
•
•
•
Connect the XLR connector to MIC socket.
Press and keep pressed the microphone switch.
Dial the two digits to access the zone desired or dial 00 for all-call.
Make a page.
Release the microphone switch.
Repeat procedure to page again.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 15:
SINGLE AMPLIFIER BACKGROUND MUSIC LINE-LEVEL SIGNAL
Single amplifier BGM operation is a programmable feature that lets the PCM2000 use the paging amplifier to provide high-power BGM to the
25/70V AC speakers when the paging system is idle.
INSTALLATION:
STEP 1: ConnectingTelephone System Paging Output to the PCMTIM
•
Refer to paging access modes described previously in Step 2 on pages 5 (paging port/contact closure), 7 (paging port/VOX), 9 (loop start
trunk), 11 (ground start trunk), or 13 (station level/Centrex).
STEP 2: Connecting the BGM Source
Connect the BGM source output to the PCMTIM module terminals labeled BGM SOURCE IN/RT.
STEP 3: PCMCPU Switch Settings
•
•
Remove the switch lock on the PCMCPU module and place the PROGRAM/RUN switch to the PROGRAM position (down), the green
LED will illuminate.
STEP 4:Testing the System
•
Access the PCM2000 system (either use a single 2500-series line telephone or butt set or dial the paging access number from the tele-
phone system).You will hear 3 beep tones indicating access to the programming mode.
•
Dial 019 follow by the ( # ) key.You will hear a short double beep if the programming was accepted and stored in the system.
STEP 5: Prepare System for Operation
•
Hang up the programming phone and then place the PROGRAM/RUN switch in the RUN position.The green LED will go out. Replace
the switch lock.
Music Source
PCM
TIM
Bogen TP30D
S1
S2
S3
S4
S5
S6
S7
TEL
INT
SEL
POWER
UP
BAND MSCAN
M1
M4
M2
M5
M3
M6
0
1
TP30D DIGITAL TUNER
POWER
DOWN MONO
ME
BOGEN
TONE VOLUME
BGM SRC
VOLUME
NIGHT RING
TEL
LINE
OVER RIDE
IN
BGM
SRC
RT
NC
COM
RLY ONE
RLY TWO
NO
NC
COM
NO
GND ST
32
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION 16:
RELAY DRIVER OUTPUT
PCM
ZPM
ZONE A
ZONE B
ZONE C
OFF ON
TALKBACK
SUPRESSION DIODES
POWER
LPBGM
VOLUME
BGM
OUT
IN
RELAY
RELAY
RELAY
ZONE A
ZONE B
ZONE C
GLOBL BGM
LO PWR
OUTPUT
HI PWR
IN
LOCAL
BGM
RT
+
ZONE A
-
+
ZONE B
ZONE C
-
+
-
RD A
RD B
RD C
POWER
SUPPLY
12VDC
RD COM
-
+
Each PCMZPM module has three relay driver outputs - RD A, RD B, and RD C - one for each speaker zone.
When a zone is activated, its relay driver is shorted to RD COM through an open collector transistor.These drivers can be used to activate
external relays to provide greater power capacity or to operate external equipment.The power supply for these relays must be 12V DC or
less.The total sink current per driver can not exceed 100mA.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION II - PROGRAMMING
SYSTEM PROGRAMMING
System programming lets you set certain PCM options and tone features using the DTMF keys of a telephone. It also lets you program pag-
ing zone groups and signaling zone groups.
All programming is accomplished through the TEL LINE jack on the PCMTIM module regardless of the telephone interface used.
Note:To simplify initial programming, it is recommended that you use the Loop StartTrunk configuration with a single-line
2500-series telephone or your Butt Set connected to theTEL LINE input.
You do not need to program the system to set the zones.The system is ready from the factory to access individual zones
and All-Call.
To program the PCM2000 system, follow these instructions:
PCM
CPU
S1
SYS
ID
S2
S3
S4
0
1
POWER
RUN
PROGRAM
1. Remove the switch lock on the PCMCPU module and place the PROGRAM/RUN switch to the PROGRAM position (down).The green
LED will illuminate.
2.Access the PCM2000 system (either use a single 2500-line telephone or butt set or dial the paging access number from the telephone sys-
tem).
3.You will hear 3 beep tones indicating access to the programming mode.
4. Dial the Feature Code for the option you wish to program. (See Feature Codes and Defaults list.)
Note:After you have entered a Feature Code (and any other data), you must press the [#] key to enter it into the system.
If the system accepts the code (and data), you will hear a short double beep confirming that the data has been stored in
the system.
Continue with the next Feature Code immediately after the confirming double beep.
If the information is not accepted, you will hear a busy tone. In this case, you should hang-up, check the code and the data, then re-access the
system and try again.
5. Once you have finished programming, you must first hang-up the programming phone and then place the Program/Run switch in the Run
position.The green LED will go out. Replace the switch lock.
Remember to press the [#] key after you enter a Feature Code.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURE CODES AND DEFAULTS
Feature
Feature Code
Additional Data
Default
Privacy Beep
Inhibit
006
007
Enable
Enable
Pre-announceTone
Inhibit
003
004
005
Beep
Chime
Chime
Inhibit
ConfirmationTone
Inhibit
001
Enable
002
Emergency O/RTone
Inhibit
008
009
Inhibit
Enable
Enable
All-Call
Inhibit
Enable
010
011
DialingTime-out
Inhibit
Enable
012
013
Enable
Inhibit
Trunk Disconnect
Inhibit
Enable
014
015
1 Amp BGM
Inhibit
018
019
050
051
*01
Inhibit
Enable
DefaultTimer
VOXTimer
Zone Group
00-99
0-9
Zones Numbers
03 (See Note 1 - p. 37)
6 (See Note 2 - p. 37)
No Zones
"
"
"
"
*32
EM/SC
Zone Group
No Tone
*92
020
021
022
023
024
025
026
027
028
029
Zone Numbers
All-Call
Follow Contact
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
Chime
3-Second Tone
Quad Beep
Night Ring
Zone Group
No Tone
Simulated Ring
Chime
Code Call
Zone Group
Inhibit
*93
030
031
032
Zone Numbers
Zone Numbers
All-Call
Ring
*94
040
041
042
043
044
045
All-Call
Inhibit
Pattern
Echo
1 Play
1 Repeat
1 Play
2 Repeat
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock Set
Clock Sync.
060
067
068
069
HHMM
HHMM
00:00
(See Note 3 - p. 37)
Inhibit
Inhibit
Enable
TimeTrigger 1
Zone Group
Inhibit
Enable
*81
110
111
112
113
114
115
116
117
118
119
Zone Numbers
HHMM
No Zones
Inhibit
(See Note 3 - p. 37)
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
8-Second Tone
Chime
3-Second Tone
TimeTrigger 2
Zone Group
Inhibit
Enable
*82
120
121
122
123
124
125
126
127
128
129
Zone Numbers
HHMM
No Zones
Inhibit
(See Note 3 - p. 37)
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
8-Second Tone
Chime
3-Second Tone
TimeTrigger 3
Zone Group
Inhibit
Enable
*83
130
131
132
133
134
135
136
137
138
139
Zone Numbers
HHMM
No Zones
Inhibit
(See Note 3 - p. 37)
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
8-Second Tone
Chime
3-Second Tone
TimeTrigger 4
Zone Group
Inhibit
Enable
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
8-Second Tone
*84
140
141
142
143
144
145
146
147
148
Zone Numbers
HHMM
No Zones
Inhibit
(See Note 3 - p. 37)
3-Second Tone
TimeTrigger 5
Zone Group
Inhibit
Enable
*85
150
151
152
153
154
155
156
157
158
159
Zone Numbers
HHMM
No Zones
Inhibit
(See Note 3 - p. 37)
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
8-Second Tone
Chime
3-Second Tone
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TimeTrigger 6
Zone Group
*86
160
161
162
163
164
165
166
167
168
169
Zone Numbers
HHMM
No Zones
Inhibit
(See Note 3 - below)
Inhibit
Enable
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
8-Second Tone
Chime
3-Second Tone
TimeTrigger 7
Zone Group
Inhibit
Enable
*87
170
171
172
173
174
175
176
177
178
179
Zone Numbers
HHMM
No Zones
Inhibit
(See Note 3 - below)
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
8-Second Tone
Chime
3-Second Tone
TimeTrigger 8
Zone Group
Inhibit
Enable
*88
180
181
182
183
184
185
186
187
188
189
999
Zone Numbers
HHMM
No Zones
Inhibit
(See Note 3 - below)
2-Second Tone
3-Second Tone
4-Second Tone
5-Second Tone
6-Second Tone
7-Second Tone
8-Second Tone
Chime
3-Second Tone
Reset Default
SetupTone (in Program Mode Only)
Turn On
Turn Off
000
Hang Up
Notes to Feature Codes
Note 1- These 2 digits represent time in 10s of seconds, i.e., "01" = 10 seconds, "02" = 20 seconds, "03" = 30 seconds, etc. Entering "00" will
inhibit timer operation
Note 2 - This single-digit indicatesVOX delay time in seconds, i.e., "1" = 1 second, "2" = 2 seconds, etc. Entering "0" will inhibitVOX timer
operation.
Note 3 - Entering the Feature Code without additional time data will enable feature using previously programmed time data.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SYS-ID SWITCH SETTINGS CHART FOR ADDITIONAL SATELLITE SYSTEMS
Zone #’s
S1
S2
S3
S4
Master
1-9
0
0
0
0
Satellite
1
2
10-18
19-27
28-36
37-45
46-54
55-63
64-72
73-81
82-90
91-99
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
1
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
3
4
5
6
7
8
9
10
APPENDIX
Module Assembly
Align polarizing tab in slot
Align connectors
so locking ridge
faces header wall.
LOCKING
TAB
LOCKING
TAB
LOCKING
SLOT
ALIGN
CONNECTORS
SO LOCKING
RIDGE FACES
HEADER WALL
6-pin Connector
Ribbon Cable Connector
ALIGN
POLARIZING
TAB IN SLOT
LOCKING
TAB
SCREW
CLAMP
TAB &
SLOT
LOCKING
SLOT
Completed Assembly
PCM
ZPM
PCM
TBM
PCM
CPU
PCM
TIM
S/N
E
M
A
D
I
N
K
O
R
E
A
38
Download from Www.Somanuals.com. All Manuals Search And Download.
50 Spring Street, Ramsey, NJ 07446 U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|