Lift-Off®
B A G L E S S
U S E R ’ S G U I D E
3750/6595 SERIES
3
Safety Instructions
Product Diagram
Assembly
4
4-6
6-8
Operations / Special Tools
Maintenance
9-13
Troubleshooting
14
15
Replacement Parts
15
Consumer Services
16
Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
ꢀ
Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
Turn off all controls before plugging or
unplugging vacuum cleaner.
Use extra care when cleaning stairs.
When using an electrical appliance,
basic precautions should be observed,
including the following:
ꢀ
READ ALL INSTRUCTIONS
BEFORE USING YOUR
UPRIGHT VACUUM.
Always connect to a polarized outlet (left slot is
wider than right). Unplug from outlet when not
in use and before conducting maintenance.
ꢀ
ꢀ
ꢀ
Unplug before attaching the turbo brush.
Do not pick up flammable materials (lighter
fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapors.
ꢀ
ꢀ
Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
Do not use vacuum cleaner in an enclosed
space filled with vapors given off by oil
base paint, paint thinner, some moth
proofing substances, flammable dust, or
other explosive or toxic vapors.
Do not pick up hard or sharp objects such
as glass, nails, screws, coins, etc.
Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
WARNING: To reduce the risk of
fire, electric shock, or injury:
ꢀ
Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
Do not leave vacuum cleaner unattended
when it is plugged in.
Unplug from outlet when not in use and
before servicing.
Do not use outdoors or on wet surfaces.
Do not allow children to operate vacuum
cleaner or use as a toy.
Close attention is necessary when used by
or near children.
Do not use for any purpose other than
described in this User’s Guide.
Use only manufacturer’s recommended
attachments.
Do not use with damaged cord or plug.
If appliance is not working as it should,
has been dropped, damaged, left outdoors,
or dropped into water, have it repaired at
an authorized service center.
Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
appliance over cord. Keep cord away from
heated surfaces.
Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
Do not handle vacuum cleaner or plug with
wet hands.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Do not use without filters in place.
Use only on dry, indoor surfaces.
Keep appliance on a level surface.
ꢀ
WARNING: The Power Cord on this product
contains lead, a chemical known to the State
of California to cause birth defects or other
reproductive harm. WASH HANDS AFTER
HANDLING.
ꢀ
ꢀ
ꢀ
SAVE THESE INSTRUCTIONS
FOR FUTURE USE.
ꢀ
THIS APPLIANCE HAS A
POLARIZED PLUG.
To reduce the risk of electric shock, this
ꢀ
ꢀ
ꢀ
appliance has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a proper
outlet. Do not change the plug in any way.
Do not put any object into openings. Do
not use with any opening blocked; keep
openings free of dust, lint, hair, and
anything that may reduce air flow.
This model is for household use only.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Comfort Grip
Handle
Cord Clip
Dusting Brush/
Upholstery Tool
Hose Clip
Release Button
Stretch Hose
Quick Release
Cord Wrap
Upper
Tank
Knob
Power
Switch
Brush On/Off
Switch
Crevice
Tool
Carrying
Handle
Detachable
Canister
Louvers/Filter Frame
Hepa
Media
Post-
Motor
Filter
Upper Tank Filter
(Inside Louvers)
Telescoping
Extension Wand
Upper Tank
Hose Grip
Power
Cord
Dirt Container
Lock ’n
Seal™ Lever
Pre-Motor Filter
Handle Release Pedal
Hose
Grip Base
Headlight
Height
Adjustment
Knob
CAUTION:
Furniture
Protection
Guard
Powerfoot
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
Download from Www.Somanuals.com. All Manuals Search And Download.
How To Use This Guide
WARNING:
This User’s Guide has been designed to help you get the
most satisfaction from your BISSELL Lift-Off. You’ll find
assembly and operating instructions, safety precautions, as well
as maintenance and troubleshooting instructions. Please read
this Guide thoroughly before assembling your vacuum cleaner.
Plastic film can be dangerous.
To avoid danger of suffocation,
keep away from babies
and children.
Pay particular attention to the product diagram, assembly
instructions, and part names. Locate and organize all parts
before assembly. Familiarize yourself with the parts and where
they fit. Following this User’s Guide will greatly enhance your
ability to get the most performance from your BISSELL Lift-Off
for many years.
How To Put It Together
The only tool you’ll need to assemble your vacuum cleaner
is a screwdriver.
Attach Handle To Vacuum
Locate the vacuum Handle and remove the screw packet
taped to the base of the Handle.
1.
Stand the vacuum upright and slide the base of the Handle
firmly into the grooves at the top of the vacuum body.
2.
Check to be sure the Handle is fitted to the vacuum
body. If there is a gap in front, continue to push firmly
3.
until the Handle is flush.
Insert two of the screws from the screw packet into the
existing holes. Tighten securely with a screwdriver.
4.
Attach Vacuum Hose and Tools
Position the Hose Assembly on the back of the canister
as shown.
1.
Attach the Hose with the remaining two screws from the
packet. Tighten securely with a screwdriver.
2.
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Vacuum Hose and Tools Continued
Slide the end of the Hose Grip onto the Hose Grip Base.
Place the Hose into the Hose Clip.
3.
4.
NOTE: The Powerfoot will not operate effectively
unless the Hose is firmly attached to the base.
Combination
Tool
Snap the Telescoping Extension Wand, Crevice Tool, and
Combination Tool into the storage clips as shown.
Telescoping
Wand
Crevice Tool
How To Use Your BISSELL Lift-Off
Power Cord Quick Release
CAUTION:
The Power Cord is stored at the side of the Detachable
Canister, wrapped around two Cord Wraps. A molded clip
on the polarized plug allows it to be fastened to the
Power Cord during storage.
Before using your vacuum, make
sure that the Dirt Container and
Upper Tank are in locked position
and that all filters (Upper Tank,
Pre-Motor and Post-Motor) are in
place. Do not operate your vacuum
without these filters.
Unclip polarized plug from Power Cord.
1.
Rotate the Upper Cord Wrap toward floor and slip the
Power Cord off.
2.
Quick Release
Cord Wrap
Plug the polarized plug into a polarized outlet.
3.
4.
To keep the Power Cord out of your way while cleaning,
place it in the Cord Clip, located near the top of
the Handle.
Power Switch/Brush Switch
The Power Switch is located just below the handle on the front of
the Detachable Canister. Push the rocker switch “ON” (I) to
vacuum, and “OFF” (O) when cleaning is complete.
The Brush Switch is located just below the handle on the front of
the Detachable Canister next to the Power Switch. This switch
turns the Rotating Brush on and off. The Brush Switch should be
in the “ON” (I) position for normal carpet cleaning. You may want
to turn the Brush Switch “OFF” (O) for bare floor cleaning or other
delicate surfaces.
Brush
Power
Note: Your BISSELL Lift Off vacuum is equipped
with a special internal switch that turns the
Rotating Brush off whenever the unit is in the
Upright position.
Handle Positions
Upright – For storage and above floor cleaning with tools.
1.
Normal Cleaning – Press the Handle Release Pedal with
your foot to recline.
2.
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Height Adjustment
Tip:
The Powerfoot on your BISSELL Lift-Off can be adjusted to clean
several floor surfaces.
Before cleaning
under low
furniture, check
area first for
objects that
might harm the
unit or block the
Vacuum Hose.
NOTE: For optimal cleaning performance, adjust to
the lowest practical setting. If your cleaner is
difficult to push, adjust to the next higher setting.
Place Handle in Upright Position.
1.
Turn Height Adjustment Knob to desired setting.
2.
Lowest Setting – For bare floors.
Medium Settings – For short and medium pile carpets.
Highest Setting – For plush pile carpet.
NOTE: You may also adjust the setting while in
the Normal Cleaning Position.
Special Tools
Your BISSELL Lift-Off is not only a powerful floor vacuum cleaner,
it’s also a versatile stairs and above floor vacuum when you select
one of the special tools.
Note: The tools can be used with the vacuum in the
Upright Position or with the Detachable Canister.
Detach the Vacuum Hose by grasping the Hose Grip and
lifting to separate from the Hose Grip Base.
1.
Attach tools by firmly pushing onto Vacuum Hose or
Telescoping Extension Wand.
2.
Combination Dusting Brush/Upholstery Tool:
Two types of cleaning tools are included in one attach-
ment: rotate for desired tool.
ꢀ Use Brush side to dust furniture, blinds, books,
lamps, shelves, and baseboards.
ꢀ Use Upholstery side for curtains, draperies, cush-
ions, fabrics.
Crevice Tool:
Use in tight narrow spaces.
Stair Cleaning Tool:
Use for stairs, area rugs, and other small carpeted
areas. This tool can also be used for bare floors.
CAUTION:
Always place vacuum cleaner
on floor in its fully Upright
Position and make sure it is
locked into place before
removing Canister or when
using tools. Placing the Lift
Off in its full Upright Position
automatically stops the
rotating brush.
Telescoping Extension Wand:
Use with desired attachment for a longer reach.
To extend the Wand, twist the collar to “Unlock”
position and push away from you. Twist the collar to
the “Lock” position to lock into place. To retract,
twist to unlock, pull toward you and twist to relock.
All items may not be included with your model. More
tools are available; to order please refer to page 15.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning With The Detachable Canister
Release
Button
The Detachable Canister feature makes it possible to easily take
the powerful cleaning action of your BISSELL Lift-Off to stairways,
auto interiors, and other hard-to-reach areas of your home.
Before detaching the Canister, your Lift-Off must be in its fully
Upright Position. You do not need to turn off the power first.
Press the Release Button at the top of the Canister
Handle and lift the Canister to remove.
1.
Detach the Vacuum Hose from the Hose Grip Base at the
back of the Canister.
2.
Attach the desired tool(s) to the Hose Grip at the end of
the Vacuum Hose.
3.
When you’re done, remove the tool(s) and reconnect the
Hose to the Hose Grip Base.
4.
Return the Canister to the Powerfoot by aligning the “feet”
5.
on the front with the bumps on the foot of the Upright
Vacuum. Push the Canister toward the vacuum frame until
it “clicks” into place.
NOTICE:
While vacuuming, certain
carpets and low humidity
conditions may generate small
static discharges. The discharges
are entirely harmless and are
not associated in any way with
the main power supply.
Power Cord Storage
When you are done using your BISSELL Lift-Off, return it to the
Upright position and store the Power Cord.
Turn vacuum cleaner off (O).
1.
Unplug Power Cord by grasping the polarized plug (NOT
2.
3.
4.
the cord) and disconnect from outlet.
Loop Power Cord around Cord Wraps on side of
the Canister.
Clip molded plug to Power Cord to secure.
CAUTION:
Do not press the Release Button
while using the Carrying Handle to
transport the vacuum cleaner. The
Canister could detach causing
the rest of the vacuum to fall.
Transporting Cleaner
To move your vacuum cleaner from room to room, put
the Handle in the Upright Position, tilt the cleaner back
on its rear wheels and push forward.
1.
2.
Carrying
Handle
The cleaner can also be moved by using the Carrying
Handle on the Detachable Canister.
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Maintain Your BISSELL Lift-Off
To maintain maximum cleaning performance, the following
maintenance steps must be performed:
WARNING:
To
Empty the Dirt Container when the dirt reaches the “Full”
line on the side.
reduce the risk of electric
shock, turn Power Switch
OFF and disconnect
1.
polarized plug from
Check the Upper Tank and Pre-Motor Filters monthly and
clean and replace as needed.
electrical outlet before
performing maintenance or
troubleshooting checks.
2.
Replace the HEPA Media Post-Motor Filter every
3.
six months.
NOTE: More frequent filter cleaning may be
necessary if you are vacuuming new carpet, fine
dust, or have allergy concerns.
Tip:
For maximum
Follow the instructions on the following pages to
perform these simple maintenance steps.
cleaning performance,
check and clean or
replace all filters
as suggested.
Empty Dirt Container
The Dirt Container needs to be emptied when the dirt reaches the
“Full” line on the side of the Container.
Unplug cleaner from electrical outlet.
Full Line
1.
Lock Position
Slide the Lock ‘n Seal Lever to the “Unlock” position.
Unlock
Position
2.
Grasp handle and pull the Dirt Container straight out to
remove from vacuum.
3.
Empty dirt into garbage container.
4.
Put the Dirt Container back in the vacuum and slide the
lever to the “Lock” position.
5.
Note: The Dirt Container may be washed in
warm water with a mild detergent. Make
sure it is completely dry before using again.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning The Upper Tank & Filter
Use only BISSELL Replacement Filters in your BISSELL Lift-Off.
Upper Tank Filter 203-1085
Unplug the cleaner from electrical outlet.
1.
The Upper Tank Filter can be reached by removing the
Dirt Container, reaching underneath the Upper Tank and
2.
turning the rim of the Filter Frame to unlock. Pull straight
down to remove. Brush the dirt off the Louvers and
Upper Tank Filter.
The foam Upper Tank Filter may be removed and hand
washed in cold water with mild detergent. Rinse well
3.
then air dry thoroughly before replacing.
The Upper Tank and Louvers may also be wiped clean
4.
with a damp cloth.
Note: For easier access, the entire Upper Tank
may be removed by turning the knob on the
back of the cleaner to unlock and pulling the
entire tank straight out.
Upper
Tank
Knob
Cleaning The Pre-Motor and Post-Motor Filters
Use only BISSELL Replacement Filters in your BISSELL Lift-Off®.
Pre-Motor Filter 203-1073
HEPA Media Post-Motor Filter #3091
Unplug the cleaner from electrical outlet.
1.
Pre-Motor Filter
The Pre-Motor Filter protects the motor from dirt particles.
It is located in the slide out tray underneath the Dirt
2.
Container. If the filter becomes dirty, pull out the tray, lift
out the filter and clean. This filter may be hand washed in
cold water with mild detergent. Rinse well and air dry
thoroughly before replacing.
Hepa Media
Post-Motor Filter
The HEPA Media Post-Motor Filter assists in the filtration
process to return clean air to the room. It is located
3.
behind the door on the back of the cleaner. If the filter
becomes dirty, open the door, remove the filter and
replace. The HEPA Media Filter is not washable.
WARNING:
Do not operate cleaner
with damp or wet
filters or without all
filters in place.
Download from Www.Somanuals.com. All Manuals Search And Download.
Check Rotating Brush and Drive Belt
You should check your vacuum cleaner’s Rotating Floor Brush and
Drive Belt regularly for wear or damage. You should also clean the
brush and brush ends of strings, hair, and carpet fibers. These can
wrap around the brush and hamper its ability to effectively clean
your carpet. Also remove any debris that has accumulated under
the brush cover.
CAUTION:
To reduce the risk of
injury from moving
parts, turn off vacuum
cleaner and disconnect
Power Plug from
Unplug cleaner from electrical outlet.
1.
electrical outlet.
Remove Detachable Canister from vacuum cleaner.
2.
Recline Handle and turn vacuum cleaner over so bottom
side is up.
3.
Remove the six screws as shown with a Phillips
head screwdriver. Lift the Brush Cover off.
4.
Grasp Rotating Floor Brush at both ends and lift.
5.
Clean strings, hair and other debris from Rotating Floor
brush, paying particular attention to brush ends.
6.
Clean strings, hair and other debris from Motor Pulley
and Drive Belt areas.
7.
Check Drive Belt carefully for wear, cuts or
stressed areas.
8.
Motor Pulley
Air Passageway
Check Air Passageway for obstructions. Remove debris
from this area.
9.
Download from Www.Somanuals.com. All Manuals Search And Download.
Replace Drive Belt
Use only BISSELL Style 8 Replacement Belts (#3200) in your BISSELL Lift-Off.
Unplug cleaner from electrical outlet.
1.
With Rotating Floor Brush removed from vacuum cleaner (Steps 1-5
of Check Rotating Floor Brush and Drive Belt), grasp old Drive Belt
2.
and remove from Motor Pulley. Discard old Drive Belt.
Place new Drive Belt over Motor Pulley and stretch other end over
Rotating Floor Brush in the space between the bristles.
3.
Place ends of Rotating Floor Brush down into slots on sides as shown.
4.
Turn Rotating Floor Brush by hand several times in the direction of
Motor Pulley. If properly installed, Drive Belt will center itself on
Rotating Brush crown.
5.
6.
Reposition Brush Cover and screws. Tighten screws securely.
Replace Light Bulb
Use only BISSELL Replacement Bulb (#203-1007) in your BISSELL Lift-Off.
Unplug cleaner from electrical outlet.
1.
Remove Detachable Canister and recline Handle of vacuum.
2.
Using a screwdriver, remove the one screw as shown and lift off the lens.
3.
Remove the bulb from the socket by pushing in gently and turning it
towards brush. Install the new bulb by pushing it gently into the
socket and turning away from brush.
4.
5.
Reposition lens and secure with the one screw.
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Clogs
Low suction or poor pickup may be due to a clog in the vacuum cleaner. If
you notice a change in the sound of the motor or a reduction in the spinning
action, check for clogs.
Unplug cleaner from electrical outlet.
1.
Empty Dirt Container.
2.
Check Upper Tank for build up or clogs.
Suction
Inlet
3.
Remove the Upper Tank and check the suction inlet for a clog.
4.
Check the clear panel on the back of the Canister for a clog. If there
5.
is an obstruction, remove the screws to remove the panel and clear
this area.
Clear
Panel
Grasp the Hose Grip and lift to separate from the suction opening.
Check for a clog in the Base or the Hose.
6.
If the clog persists, follow the instructions for Checking the Rotating
Brush on page 1x1 and inspect the Air Passageway for obstructions.
7.
Suction
Opening
Air Passageway
Thermal Protector
An internal thermal protector has been designed into your cleaner to protect
it from overheating. When the thermal protector activates, the main
vacuum motor will stop operating. If this happens, proceed as follows:
Turn the cleaner OFF (O) and unplug from electrical outlet.
1.
CAUTION:
To reduce the risk of
injury from moving
parts, turn off vacuum
cleaner and disconnect
Power Plug from
Check the Upper Tank area, Pre-Motor Filter and
Post-Motor Filter for dirt accumulation.
2.
Refer to the "Clearing Clogs" section.
3.
electrical outlet.
When the motor cools for approximately 30 minutes, the
thermal protector automatically resets and cleaning may continue. If
the thermal protector continues to activate after following the above
steps, your cleaner may need servicing. Call BISSELL Consumer
Services, or visit the website.
4.
Note: The thermal protector controls the main vacuum
motor only, not the brush motor. If the thermal protector
activates, the brush will continue to operate normally;
however, there will be no suction.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Vacuum cleaner won't run.
Possible Causes
Remedies
Power cord not firmly plugged in
Blown household fuse or breaker
Thermal protector activated
Check electrical plug
Check/replace fuse - Reset breaker
Allow cleaner to cool for 30 minutes, see pg. 13
1
2
3
1
2
3
No Power at Rotating Floor Brush.
Possible Causes
Remedies
Canister is not securely seated
Remove Canister and replace, making sure that
it “clicks” into place
1
1
Brush Switch turned to “Off”
Make sure Brush Switch is in “On” position
2
2
Vacuum cleaner or Tools won't pick up dirt.
Possible Causes
Remedies
1
Incorrect Height Adjustment
Adjust Powerfoot to correct height setting
1
Hose not attached to suction opening
Crack or hole in Hose
2 Grasp Hose Grip and firmly push onto the base
3 Check Hose and replace if needed
2
3
Drive Belt broken, worn or off motor pulley
Reposition or replace Drive Belt, see pg. 11-12
4
4
Rotating Floor Brush bristles worn
Replace brush
5
5
6 Rotating Floor Brush jammed
6 Remove brush and clean debris from brush ends
Clog in vacuum
Follow instructions on pg. 13 for clearing clogs
7
7
Dirt Container full
Empty Dirt Container
8
8
Dirt Container or Upper Tank not installed properly
Position correctly and lock in place
9
9
10 Filters are dirty
Check and clean Upper Tank, Pre-Motor and
Post-Motor Filters
10
Vacuum cleaner is difficult to push.
Possible Causes
Remedies
Incorrect Height Adjustment
Adjust Powerfoot to correct height setting
1
1
Visible dirt escaping from cleaner.
Possible Causes
Remedies
Dirt Container full
Empty Dirt Container
1
2
Filters missing or installed incorrectly
Check Upper Tank, Pre-Motor and Post-Motor
Filters for correct installation
2
3
Dirt Container installed incorrectly
3 Pull out and re-insert Dirt Container correctly
If suggested solutions do not correct the problem, call:
WARNING:
BISSELL Consumer Services
To reduce the risk of injury
from moving parts and/ or
electrical shock, turn Power
Switch OFF and disconnect
polarized plug from electrical
outlet before performing
troubleshooting checks.
1-800-237-7691
Monday - Friday 8 a.m. — 10 p.m. ET
Saturday
9 a.m. — 8 p.m. ET
or visit the BISSELL website - www.bissell.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts – BISSELL Lift-Off Series
You may purchase replacement parts from your retailer, by calling BISSELL
Consumer Services or by visiting our website. To locate a retailer near
you, or to place an order using Visa, MasterCard, Discover or American
Express, call
1
4
2
5
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
3
6
Or visit our Website - www.bissell.com
Item Part No.
Part Name
Style 8 Drive Belt (2-Pack)
Headlight Bulb
1
2
3200
203-1007
7
8
3
4
5*
6
7
8
9
10
11
203-1063
203-1099
203-6624
203-6625
203-6633
203-6619
203-1085
203-1073
3091
Crevice Tool
Dusting Brush/Upholstery Tool
Stair Cleaning Tool
Telescoping Extension Wand
Vacuum Hose
Brush Roll
Upper Tank Filter
10
11
9
Pre-Motor Filter
HEPA Media Post-Motor Filter
*May not be included with every model.
BISSELL Consumer Services
For information about repairs or replacement parts, or
questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please
contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare,
Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge
from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not
covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact
BISSELL Consumer Services.
Website or E-mail:
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR
DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.
©2003 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea.
Part Number 010-5519
Rev 7/03
Visit our website at:
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|