Wireless G+ MIMO
ADSL2+ Modem Router
�������
User Manual
����
F5D9630-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing the Belkin ADSL Modem with High-Speed
Mode Wireless G Router (the Router). In minutes you will be able to
share your Internet connection and network your computers with your
new Router. The following is a list of features that make your Router an
ideal solution for your home or small office network. Please be sure to
read through this User Manual completely, and pay special attention to
Appendix B entitled “Important Factors for Placement and Setup”.
1
2
3
•
Share one high-speed Internet connection with all the computers
in your home
4
•
Share resources, such as files and hard drives among all the
connected computers in your home
5
•
•
•
•
Share a single printer with the entire family
Share documents, music, video, and digital pictures
Store, retrieve, and copy files from one computer to another
Simultaneously play games online, check Internet email, and chat
6
7
Advantages of a Wireless Network
Here are some of the advantages of setting up a Belkin Wireless
8
Network:
9
•
Mobility – you’ll no longer need a dedicated “computer room”—
now you can work on a networked laptop or desktop computer
anywhere within your wireless range
10
•
•
•
Easy installation – Belkin’s Easy Installation Wizard makes setup
simple
Flexibility – set up and access printers, computers, and other
networking devices from anywhere in your home
Easy Expansion – the wide range of Belkin networking products let
you expand your network to include devices such as printers and
gaming consoles
•
•
No cabling required – you can spare the expense and hassle of
retrofitting Ethernet cabling throughout the home or office
Widespread industry acceptance – choose from a wide range of
interoperable networking products.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Placement of your Wireless G Plus MIMO ADSL2+
Modem Router
Important Factors for Placement and Setup
Your wireless connection will be stronger the closer your computer is
to your Router. Typical indoor operating range for wireless devices is
between 100 and 200 feet.
In the same way, your wireless connection and performance will
degrade somewhat as the distance between your Router and
connected devices increases. This may or may not be noticeable to
you. As you move further from your Router, connection speed may
decrease. Factors that can weaken signals simply by getting in the way
of your network’s radio waves are metal appliances or obstructions,
and walls.
If you have concerns about your network’s performance that might
be related to range or obstruction factors, try moving the computer
to a position between five and 10 feet from the Router in order to see
if distance is the problem. If difficulties persist even at close range,
please contact Belkin Technical Support.
Note: While some of the items listed below can affect network
performance, they will not prohibit your wireless network from
functioning; if you are concerned that your network is not operating at
its maximum effectiveness, this checklist may help.
1. Router Placement
Place your Router, the central connection point of your network, as
close as possible to the center of your wireless network devices. To
achieve the best wireless network coverage for your “wireless clients”
(i.e., computers enabled by Belkin Wireless Notebook Network Cards,
Wireless Desktop Network Cards, and Wireless USB Adapters):
•
Ensure that your Router’s networking antennas are parallel to each
other, and are positioned vertically (toward the ceiling). If your
Router itself is positioned vertically, point the antennas as much as
possible in an upward direction.
•
•
In multistory homes, place the Router on a floor that is as close
to the center of the home as possible. This may mean placing the
Router on an upper floor.
Try not to place the Router near a cordless 2.4GHz phone.
The Router is designed to be placed on a desktop. All of the cables exit
from the rear of the Router for better organization and utility. The LED
indicators are easily visible on the front of the Router to provide you with
information about network activity and status.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1
2
2. Avoid Obstacles and Interference
Avoid placing your Router near devices that may emit radio “noise,”
such as microwave ovens. Dense objects that can inhibit wireless
communication include:
•
•
•
•
•
Refrigerators
Washers and/or dryers
Metal cabinets
Large aquariums
Metallic-based UV tinted windows
3
4
If your wireless signal seems weak in some spots, make sure that
objects such as these are not blocking the signal’s path (between your
computers and Router).
5
6
3. Cordless Phones
If the performance of your wireless network is impaired after attending
to the above issues, and you have a cordless phone:
7
•
Try moving cordless phones away from your Router and your
wireless-enabled computers.
8
•
Unplug and remove the battery from any cordless phone that
operates on the 2.4GHz band (check manufacturer’s information).
If this fixes the problem, your phone may be interfering.
If your phone supports channel selection, change the channel
on the phone to the farthest channel from your wireless network.
For example, change the phone to channel 1 and move your
Router to channel 11. See your phone’s user manual for detailed
instructions.
9
•
•
10
If necessary, consider switching to a 900MHz or 5GHz cordless phone.
4. Choose the “Quietest” Channel for your Wireless Network
In locations where homes or offices are close together, such as
apartment buildings or office complexes, there may be wireless
networks nearby that can conflict with yours. Use the Site Survey
capabilities found in the Wireless Utility of your wireless adapter to
locate any other wireless networks that are available (see your wireless
adapter’s user manual), and move your Router and computers to a
channel as far away from other networks as possible.
•
Experiment with more than one of the available channels, in
order to find the clearest connection and avoid interference from
neighboring cordless phones or other wireless devices.
•
For Belkin wireless networking products, use the detailed Site
Survey and wireless channel information included with your
wireless network card. See your network card’s user guide for
more information.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
These guidelines should allow you to cover the maximum possible area
with your Router. Should you need to cover an even wider area, we
suggest the Belkin Wireless Range Extender/Access Point.
5. Secure Connections, VPNs, and AOL
Secure connections typically require a user name and password, and
are used where security is important. Secure connections include:
•
Virtual Private Network (VPN) connections, often used to connect
remotely to an office network
•
The “Bring Your Own Access” program from America Online (AOL),
which lets you use AOL through broadband provided by another
cable or DSL service
•
•
Most online banking websites
Many commercial websites that require a user name and password
to access your account
Secure connections can be interrupted by a computer’s power
management setting, which causes it to “go to sleep.” The simplest
solution to avoid this is to simply reconnect by rerunning the VPN or
AOL software, or by re-logging into the secure website.
A second alternative is to change your computer’s power
management settings so it does not go to sleep; however, this may
not be appropriate for portable computers. To change your power
management setting under Windows, see the “Power Options” item in
the Control Panel.
If you continue to have difficulty with Secure Connections, VPNs, and
AOL, please review the steps above to be sure you have addressed
these issues.
For more information regarding our networking products, visit our website
USA:
877-736-5771
310-898-1100 ext. 2263
0845 607 77 87
1800 235 546
UK:
Australia:
New Zealand:
Singapore:
0800 235 546
800 616 1790
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
1
2
Product Features
Product Features
In minutes you will be able to share your Internet connection and
network your computers. The following is a list of features that make
your new Belkin Wireless G Plus MIMO ADSL2+ Modem Router an
ideal solution for your home or small office network.
3
4
Works with Both PCs and Mac® Computers
The Router supports a variety of networking environments including
Mac OS® 8.x, 9.x, X v10.x, Linux®, Windows® 98, Me, NT®, 2000, XP,
and Vista™, and others. All that is needed is an Internet browser and
a network adapter that supports TCP/IP (the standard language of the
Internet.
5
6
Web-Based Advanced User Interface
7
You can set up the Router’s advanced functions easily through your
web browser, without having to install additional software onto the
computer. There are no disks to install or keep track of and, best of all,
you can make changes and perform setup functions from any computer
on the network quickly and easily.
8
9
NAT IP Address Sharing
10
Your Router employs Network Address Translation (NAT) to share the
single IP address assigned to you by your Internet Service Provider
while saving the cost of adding IP addresses to your Internet service
account.
SPI Firewall
Your Router is equipped with a firewall that will protect your network
from a wide array of common hacker attacks including IP Spoofing,
Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero
length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear
Drop Attack, ICMP defect, RIP defect, and fragment flooding.
Integrated 10/100 4-Port Switch
The Router has a built-in, four-port network switch to allow your wired
computers to share printers, data and MP3 files, digital photos, and
much more. The switch features automatic detection so it will adjust to
the speed of connected devices. The switch will transfer data between
computers and the Internet simultaneously without interrupting or
consuming resources.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
Universal Plug and Play (UPnP)
UPnP is a technology that offers seamless operation of voice
messaging, video messaging, games, and other applications that are
UPnP-compliant.
Support for VPN Pass-Through
If you connect to your office network from home using a VPN
connection, your Router will allow your VPN-equipped computer to
pass through the Router and to your office network.
Built-In Dynamic Host Configuration Protocol (DHCP)
Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes
for the easiest possible connection of a network. The DHCP server
will assign IP addresses to each computer automatically so there is no
need for a complicated networking setup.
Setup Assistant
The Setup Assistant, second generation of Belkin’s renowned Easy
Install Wizard, takes the guesswork out of setting up your Router. This
automatic software determines your network settings for you and sets
up the Router for connection to your Internet Service Provider (ISP). In
a matter of minutes, your Router will be up and running on the Internet.
Note: Setup Assistant software is compatible with Windows 2000 and
XP. If you are using another operating system, the Router can be set
up using the Alternate Setup Method described in this User Manual
(see page 22).
Integrated Wireless G Plus MIMO Access Point
Wireless G Plus MIMO is an exciting new wireless technology.
It employs MIMO (Multiple Input Multiple Output) smart-antenna
technology that achieves data rates above the standard 802.11g
throughput. Actual throughput is typically lower than the connected
data rate and will vary depending on your networking environment.
MAC-Address Filtering
For added security, you can set up a list of MAC addresses (unique
client identifiers) that are allowed access to your network. Every
computer has its own MAC address. Simply enter these MAC
addresses into a list using the Web-Based Advanced User Interface
and you can control access to your network.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Knowing your Router
1
2
Package Contents
•
•
•
•
•
•
•
•
Belkin Wireless G Plus MIMO ADSL2+ Modem Router
Quick Installation Guide
Belkin Setup Assistant Software CD
RJ11 Telephone Cord
3
RJ45 Ethernet Networking Cable
ADSL (Asymmetric Digital Subscriber Line) Microfilter*
Power Supply
4
5
User Manual in CD
6
*ADSL microfilter varies by country. If it’s not included, you will need to
purchase one.
7
System Requirements
8
•
An active ADSL service with a telephone wall jack for connecting
the Router
•
•
•
At least one computer with an installed network interface adapter
TCP/IP networking protocol installed on each computer
9
No other DHCP server on your local network assigning IP
addresses to computers and devices
10
•
Internet browser
Setup Assistant Software System Requirements
•
A PC running Windows® 2000 or XP
•
Minimum 500MHz processor and 128MB RAM
•
Internet browser
Internet Connection Settings
The Setup Assistant contains a database of Internet Service Providers
(ISPs) in each country to help you set up your Router quickly. If your
ISP is not on the list, please collect the following information from your
ISP before setting up the Router:
•
Internet connection protocol: _________ (PPPoE, PPPoA, Dynamic
IP, Static IP)
•
Multiplexing method or Encapsulation: _________ (LLC or VC MUX)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Knowing your Router
•
•
Virtual circuit: VPI (Virtual Path Identifier) __________
(a number between 0 and 255)
VCI (Virtual Channel Identifier) __________
(a number between 1 and 65535)
•
•
For PPPoE and PPPoA users: ADSL account user name ________
and password _______________
For static IP users: IP Address ___ . ___ . ___ . ___
Subnet Mask ___ . ___ . ___ . ___
Default Gateway Server ___ . ___ . ___ .
•
IP address for Domain Name Server ___ . ___ . ___ . ___ (If given
by your ISP)
The Network Status Display
The Router has been designed to be placed on a desktop. All of the
cables exit from the rear of the Router for better organization and
utility. The Network Status Display is easily visible on the FRONT of
the Router to provide you with information about network activity
and status. See the Network Status Display Guide for more detailed
information.
Front Panel
(1)
(2)
(3)
(4) (5)
1. Power LED
When you apply power to the Router or restart it, a short period of time
elapses while the Router boots up. When the Router has completely
booted up, the Power LED becomes a GREEN light, indicating the
Router is ready for use.
OFF
Router is OFF
Green
Red
Router is ON
Router failed to start
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Knowing your Router
1
2
2. LAN Status LEDs
These LAN Status LEDs are labeled 1–4 and correspond to the
numbered ports on the rear of the Router. When a computer is properly
connected to one of the LAN ports on the rear of the Router, the LED
will light. Solid GREEN means a computer or a network-enabled device
is connected. When information is being sent over the port, the LED
blinks rapidly. ORANGE indicates a 10Base-T connection.
3
4
Orange
Ethernet link is up and 10Base-T
device connected
5
Orange - blinking
Green
10Base-T device is transmitting or
receiving data
Ethernet link is up and 100Base-T
device is connected
6
Green - blinking
100Base-T device is transmitting or
receiving data
7
8
3. WLAN Status LED
9
The WLAN Status LED is solid GREEN when you enable the wireless
LAN function. It flashes when the Router is transmitting or receiving
data wirelessly.
10
Green
WLAN is up and connected
Transmitting or receiving data
Green - blinking
4. ADSL LED
The ADSL LED flashes GREEN during negotiation with your ISP. It stays
GREEN when the Router is connected properly to your ADSL service.
OFF
Green - blinking Negotiating connection
Green ADSL link is up and connected
No ADSL connection
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Knowing your Router
5. Internet LED
The Internet LED shows you when the Router is connected to the
Internet. When the LED is OFF, the Router is NOT connected to the
Internet. When the LED is solid GREEN, the Router is connected to
the Internet. When the LED is blinking, the Router is transmitting or
receiving data from the Internet.
OFF
No Internet connection
Green
Connected to the Internet
Green - blinking Transmitting or receiving data
Red
Failed to connect to the Internet
Back Panel
(6)
(9) (8)
(7)
6. DSL Line
This port is for connection to your ADSL. Connect your ADSL to this
port.
7. Ethernet Ports
The Ethernet ports are RJ45, 10/100 auto-negotiation. The ports are
labeled 1 through 4. These ports correspond to the numbered LEDs on
the front of the Router. Connect your network-enabled computers or
any networking devices to one of these ports.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Knowing your Router
1
2
8. Reset Button
The “Reset” button is used in rare cases when the Router may function
improperly. Resetting the Router will restore the Router’s normal
operation while maintaining the programmed settings. You can also
restore the factory default settings by using the “Reset” button. Use
the restore option in instances where you may have forgotten your
custom password.
3
4
a.
Resetting the Router
Push and hold the “Reset” button for one second, then
release it. When the “Power/Ready” light becomes solid
again, the reset is complete.
5
6
b.
Restoring the Factory Defaults
Press and hold the “Reset” button for at least five seconds,
then release it. When the “Power/Ready” light becomes solid
again, the restore is complete.
7
8
9. Power Plug
9
Connect the included DC power supply to this inlet. Using the wrong
type of power adapter may cause damage to your Router.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
Verify the contents of your box. You should have the following:
•
•
•
•
•
•
Belkin Wireless G Plus MIMO ADSL2+ Modem Router
RJ11 Telephone Cord
RJ45 Ethernet Networking Cable
Power Supply
Belkin Setup Assistant Software CD
User Manual
Setup Assistant
Belkin has provided our Setup Assistant software to make installing
your Router a simple and easy task. You can use it to get your
Router up and running in minutes. The Setup Assistant requires that
your Windows 2000 ,XP or Vista computer be connected directly to
your ADSL and that the Internet connection is active and working
at the time of installation. If it is not, you must use the “Alternate
Setup Method” section of this User Manual to configure your Router.
Additionally, if you are using an operating system other than Windows
2000,XP, or Mac OS X you must set up the Router using the “Alternate
Setup Method” section of this User Manual.
Step 1A: Hardware Connections – Follow the Quick Installation
Guide (QIG)
Brand-New Setup
Follow these steps if you are not replacing an existing modem. If you
are replacing an existing modem, skip to the next section, “Replacing
an Existing Modem or Modem Router”, starting on page 13
1A.1 Unpack your new Router from the box and place it next to your
computer. Raise the Router’s antennas.
1A.2 Retrieve the yellow RJ45 cable that was included with your
Router. First, connect one end to any yellow port labeled “Wired
Computers” on the back of your Router. Then, connect the other
end to the networking port on the back of your computer.
1A.3 Retrieve the included gray RJ11 phone cord. Connect one end
to the gray port labeled “DSL” on the back of your Router. Then
connect the other end to your ADSL connection (either a wall jack
or an ADSL splitter).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
1
2
Note: Some ADSL connections require a microfilter. Your ADSL provider
can tell you if you need one. Belkin includes a microfilter in regions
known to use them. You may or may not have received one in your box.
1A.4 Plug your Router’s power supply into the black port labeled
“Power”
on the back of your Router . Wait 30 seconds for the
3
Router to start up. Look at the front panel of the Router. Make
sure one of the “LAN” and the “POWER” LED’s are both lit up. If
they are not, recheck your connections.
4
Step 1B: Replacing an Existing Modem or Modem Router
Follow these steps if you currently have a modem or a modem router
that you will be replacing with your new Router.
5
6
1B.1 Unpack your new Router from the box and place it next to
your old modem. Raise the Router’s antennas. Unplug your old
modem’s power cord.
7
1B.2 Locate the cable that connects your old modem to your
computer. Unplug that cable from your old modem, and plug it
into any yellow port labeled “Wired Computers” on the back of
your new Router.
8
9
1B.3 Locate the cable that connects your old modem to the ADSL wall
jack. Unplug it from your old modem and then connect it to the
gray port labeled “DSL” on the back of your Router.
10
1B.4 Plug your Router’s power supply into the black port labeled
“Power” on the back of your Router.
1B.5 Wait 30 seconds for the Router to start up. Look at the front
panel on the Router. Make sure one of the “LAN” and the
“POWER” icons are lit. If they are not, recheck your connections.
Step 2: Set Up the Router – Run the Setup Assistant Software
2.1 Shut down any programs that are running on your computer at this
time. Turn off any firewall or Internet-connection-sharing software
on your computer.
2.2 Insert the CD into your computer. The Setup Assistant will
automatically appear on your computer’s screen within 15
seconds. Click on “Go” to run the Setup Assistant. Follow the
instructions there.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
Note for Windows Users: If the Setup Assistant does not start up
automatically, select your CD-ROM drive from “My Computer” and
double-click on the file named “SetupAssistant” to start the Setup
Assistant.
NOTE TO MAC® USERS: Double-click on the “Easy Install” icon to start
the Setup Assistant. Then, follow the prompts to complete the setup.
2.3 Select Country. Select your country from the drop-down box.
Click “Begin” to continue.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
1
2
2.4 Confirmation Screen. Verify that you have completed all QIG steps
by checking the box to the right of the arrow. Click “Next” to
continue.
3
4
5
6
7
8
2.5 Progress Screen. Setup Assistant will show you a progress screen
each time a step in the setup has been completed.
9
10
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
2.6 Checking Settings. The Setup Assistant will now examine your
computer’s network settings and gather information needed to
complete the Router’s connection to the Internet.
2.7 Verifying Hardware Connections. The Setup Assistant will now
verify your hardware connection.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
1
2
2.8 Naming your Wireless Network. The Setup Assistant will display the
default wireless network name or Service Set Identifier (SSID). This
is the name of your wireless network to which your computers or
devices with wireless network adapters will connect. You can either
use the default or change it to something unique. Write down this
name for future reference. Click “Next” to continue.
3
4
5
6
7
8
9
10
2.9 Requesting Internet Account Info (if needed). If your Internet
account requires a login and password, you will be prompted with
a screen similar to the illustration below. Select your country or ISP
from the drop-down boxes.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
2.10 Configuring the Router. The Setup Assistant will now configure
your Router by sending data to the Router and restarting it. Wait
for the on-screen instructions.
Note: Do not disconnect any cable or power off the Router while the
Router is rebooting. Doing so will render your Router inoperable.
2.11 Checking Internet Connection. We are almost done. The Setup
Assistant will now check your connection to the Internet.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
1
2
3
4
5
6
7
Congratulations
8
You have finished installing your new Belkin Router. You will see the
Congratulations screen when your Router can connect to the Internet.
You can begin surfing by opening your browser and going to any
website.
9
10
You can use the Setup Assistant to set up your other wired and
wireless computers to connect to the Internet by clicking “Next”. If
you decide to add computers to your Router later, select “Exit the
Assistant” and then click “Next”.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
Troubleshooting
If the Setup Assistant is not able to connect to the Internet, you will see
the following screen. Follow the on-screen instructions to go through
the troubleshooting steps.
2.12 Optional: Assistance Connecting Other Computers
This optional step will help you to connect additional wired and wireless
computers to your network. Follow the on-screen instructions.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting and Configuring your Router
1
2
Congratulations
Once you have verified that your other wired and wireless computers
are properly connected, your network is set up and working. You can
now surf the Internet. Click “Next” to take you back to the main menu.
3
4
5
6
7
8
9
10
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
Step 1: Hardware Connections – Follow the Quick Installation
Guide
See the QIG or Step 1A/B: Hardware Connections from the previous
section.
Step 2: Set your Computer’s Network Settings to Work with a
DHCP Server
See the section in this User Manual called “Manually Configuring
Network Settings” for directions.
Step 3: Configuring the Router Using the Web-Based Advanced
User Interface
Using your Internet browser, you can access the Router’s Web-Based
Advanced User Interface. In your browser, type “192.168.2.1” (do
“Enter” key.
Logging into the Router
You will see the Router’s home page in your browser window. The
home page is visible to any user who wants to see it. To make any
changes to the Router’s settings, you have to log in. Clicking the
“Login” button or clicking on any one of the links on the home page
will take you to the login screen. The Router ships with no password
entered. In the login screen, leave the password blank and click the
“Submit” button to log in.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
1
2
Logging out of the Router
One computer at a time can log into the Router for the purposes of
making changes to the settings of the Router. Once a user has logged
in to make changes, there are two ways that the computer can be
logged out. Clicking the “Logout” button will log the computer out. The
second method is automatic. The login will time out after a specified
period of time. The default login time-out is 10 minutes. This can be
changed from one to 99 minutes. For more information, see the section
in this manual titled “Changing the Login Time-Out Setting”.
3
4
5
Understanding the Web-Based Advanced User Interface
The home page is the first page you will see when you access the
Advanced User Interface (UI). The home page shows you a quick view
of the Router’s status and settings. All advanced setup pages can be
reached from this page.
6
7
8
9
10
1. Quick-Navigation Links
You can go directly to any of the Router’s advanced UI pages by
clicking directly on these links. The links are divided into logical
categories and grouped by tabs to make finding a particular setting
easier to find. Clicking on the purple header of each tab will show you
a short description of the tab’s function.
2. Home Button
The “Home” button is available in every page of the UI. Pressing this
button will take you back to the home page.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
3. Help Button
The “Help” button gives you access to the Router’s help pages. Help
is also available on many pages by clicking “more info” next to certain
sections of each page.
4. Login/Logout Button
This button enables you to log in and out of the Router with the press
of one button. When you are logged into the Router, this button will
change to read “Logout”. Logging into the Router will take you to a
separate login page where you will need to enter a password. When
you are logged into the Router, you can make changes to the settings.
When you are finished making changes, you can log out of the Router
by clicking the “Logout” button. For more information about logging
into the Router, see the section called “Logging into the Router”.
5. Internet-Status Indicator
This indicator is visible in all pages of the Router, indicating the
connection status of the Router. When the indicator says “Connected”
in blue, the Router is connected to the Internet. When the Router is not
connected to the Internet, the indicator will read “No Connection” in
RED. The indicator is automatically updated when you make changes
to the settings of the Router.
6. Version Info
Shows the firmware version, boot-code version, hardware version, and
serial number of the Router.
7. LAN Settings
Shows you the settings of the Local Area Network (LAN) side of the
Router. Changes can be made to the settings by clicking on any one
of the links (IP Address, Subnet Mask, DHCP Server) or by clicking the
“LAN” quick-navigation link on the left side of the screen.
8. Internet Settings
Shows the settings of the Internet/WAN side of the Router that
connects to the Internet. Changes to any of these settings can be
made by clicking on the links or by clicking on the “Internet/WAN”
quick-navigation link on the left side of the screen.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
1
2
Step 4: Configuring your Router for Connection to your Internet
Service Provider (ISP)
The “Internet/WAN” tab is where you will set up your Router to
connect to your ISP. The Router is capable of connecting to virtually
any ISP’s system provided you have correctly configured the Router’s
settings for your ISP’s connection type. Your ISP connection settings
are provided to you by your ISP. To configure the Router with the
settings that your ISP gave you, click “Connection Type” (A) on the
left side of the screen. Select the connection type you use. If your ISP
gave you DNS settings, clicking “DNS” (B) allows you to enter DNS
address entries for ISPs that require specific settings. Clicking “MAC
Address” (C) will let you clone your computer’s MAC address or type
in a specific WAN MAC address, if required by your ISP. When you
have finished making settings, the “Internet Status” indicator will read
“connection OK” if your Router is set up properly.
3
4
5
6
7
8
9
10
Connection Type
From the “Connection Type” page, you can select one of these five
connection types based on the instruction provided by your ISP:
•
•
•
•
•
PPPoE
PPPoA
Dynamic IP (1483 Bridged)
Static IP (IPoA)
Modem Only (Disable Internet Sharing)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
Select the type of connection you use by clicking the radio button (1)
next to your connection type and then clicking “Next” (2).
Setting your ISP Connection Type to PPPoE or PPPoA
PPPoE (Point-to-Point Protocol over Ethernet) is the standard method
of connecting networked devices. It requires a user name and
password to access the network of your ISP for connecting to the
Internet. PPPoA (PPP over ATM) is similar to PPPoE, but is mostly
implemented in the UK. Select PPPoE or PPPoA and click “Next”. Then
enter the information provided by your ISP, and click “Apply Changes”
to activate your settings.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
1
2
1. User Name - Enter the user name (assigned by your ISP).
2. Password - Enter your password (assigned by your ISP).
3. Retype Password - Confirm the password (assigned by your ISP).
3
4. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier. (VCI) parameter here (assigned by your ISP).
4
5. Encapsulation - Select your encapsulation type (supplied by your
ISP) to specify how to handle multiple protocols at the ATM transport
layer.
5
6
VC-MUX: PPPoA Virtual Circuit Multiplexer (null encapsulation) allows
only one protocol running per virtual circuit with fewer overheads.
7
LLC: PPPoA Logical Link Control allows multiple protocols running
over one virtual circuit (more overhead).
8
6. MTU – Enter the MTU value for your ISP.
9
7. Dial on Demand - By selecting “Dial on Demand”, your Router will
automatically connect to the Internet when a user opens up a web
browser.
10
8. Idle Time (Minutes) - Enter the maximum idle time for the Internet
connection. After this time has been exceeded, the connection will be
terminated.
9. Use Static Default Route – Check this box and use the static
IP address your ISP assigns for your line. Use this option only if
instructed by your ISP.
Click “Apply Changes/Next” to save and activate your settings. To
go back to the original settings before saving, click “Clear Changes”;
or click any of the quick-navigation links for other options. Your new
settings will not be saved unless you click “Apply Changes/Next”.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
Setting your Connection Type to Dynamic IP (1483 Bridged)
This connection method bridges your network and ISP’s network
together. The Router will obtain an IP address automatically from your
ISP’s DHCP server.
(1)
(2)
1. VPI/VCI - Enter your VPI and VCI parameter here. These identifiers
are assigned by your ISP.
2. Encapsulation - Select LLC or VC MUX your ISP uses.
Click “Apply Changes/Next” to save and activate your settings. To
go back to the original settings before saving, click “Clear Changes”;
or click any of the quick-navigation links for other options. Your new
settings will not be saved unless you click “Apply Changes/Next”.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
1
2
Setting your ISP Connection Type to Static IP (IPoA)
This connection type is also called “Classical IP over ATM” or “CLIP”,
which comprises a fixed IP address that your ISP provides for your
Router to connect to the Internet.
3
(1)
(2)
(3)
(4)
(5)
4
5
6
7
8
1. WAN IP Address – Enter an IP address assigned by your ISP for the
Router WAN interface.
2. WAN Subnet Mask - Enter a subnet mask assigned by your ISP.
9
3. Default Gateway - Enter a default gateway IP address. If the Router
cannot find the destination address within its local network, it will
forward the packets to the default gateway assigned by your ISP.
10
4. VPI/VCI - Enter your VPI and VCI parameter here. These identifiers
are assigned by your ISP.
5. Encapsulation - Select LLC or VC MUX your ISP uses.
Click “Apply Changes/Next” to save and activate your settings. To
go back to the original settings before saving, click “Clear Changes”;
or click any of the quick-navigation links for other options. Your new
settings will not be saved unless you click “Apply Changes/Next”.
Setting your Connection Type to Modem Only (Disable Internet
Sharing)
In this mode, the Router simply acts as a bridge passing packets
across the DSL port. It requires additional software to be installed on
your computers in order to access the Internet.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
(1)
(2)
1. VPI/VCI - Enter your VPI and VCI parameter here (assigned by your ISP).
2. Encapsulation - Select LLC or VC MUX your ISP uses.
Click “Apply Changes” to save and activate your settings. To go back
to the original settings before saving, click “Clear Changes”; or click
any of the quick-navigation links for other options. Your new settings
will not be saved unless you click “Apply Changes/Next”.
Setting Custom Domain Name Server (DNS) Settings
A “Domain Name Server” is a server located on the Internet that translates
addresses. Many Internet Service Providers (ISPs) do not require you to
enter this information into the Router. The “Automatic from ISP” box (1)
should be checked if your ISP did not give you a specific DNS address.
If you are using a static IP connection type, then you may need to enter
a specific DNS address and secondary DNS address for your connection
to work properly. If your connection type is dynamic or PPPoE, it is likely
that you do not have to enter a DNS address. Leave the “Automatic
from ISP” box checked. To enter the DNS address settings, uncheck
the “Automatic from ISP” box and enter your DNS entries in the spaces
provided. Click “Apply Changes” (2) to save the settings.
(1)
(2)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
1
2
Using Dynamic DNS
The Dynamic DNS service allows you to create an alias dynamic IP
address to a static host name in any of the many domains DynDNS.org
offers, allowing your network computers to be more easily accessed
from various locations on the Internet. DynDNS.org provides this
service, for up to five host names, free to the Internet community.
3
The Dynamic DNSSM service is ideal for a home website, file server, or
to make it easy to access your home PC and stored files while you’re
at work. Using the service can ensure that your host name always
points to your IP address, no matter how often your ISP changes it.
When your IP address changes, your friends and associates can always
locate you by visiting yourname.dyndns.org instead.
4
5
6
To register free for your Dynamic DNS host name, please visit
7
Setting up the Router’s Dynamic DNS Update Client
8
You must register with DynDNS.org’s free update service before using
this feature. Once you have your registration, follow the directions
below.
9
1. Select “DynDNS.org” from the drop-down box. Click “Apply
10
Changes”.
(1)
(2)
(3)
(4)
2. Enter your DynDNS.org user name in the “User Name” field (1).
3. Enter your DynDNS.org password in the “Password” field (2).
4. Enter the DynDNS.org domain name you set up with DynDNS.org in
the “Domain Name” field (3).
5. Click “Apply Changes” to update your IP address.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Setup Method
Whenever your IP address assigned by your ISP changes, the Router
will automatically update DynDNS.org’s servers with your new
IP address. You can also do this manually by clicking the “Apply
Changes” button (4).
(1)
(2)
(3)
(4)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
Using the Web-Based Advanced User Interface
Using your Internet browser, you can access the Router’s Web-Based
Advanced User Interface. In your browser, type “192.168.2.1” (do not
key.
3
4
5
You will see the Router’s home page in your browser window.
6
Viewing the LAN Settings
7
Clicking on the header of the LAN tab (1) will take you to the LAN tab’s
header page. A quick description of the functions can be found here.
To view the settings or make changes to any of the LAN settings, click
on “LAN Settings” (2) or to view the list of connected computers, click
on “DHCP client list” (3).
8
9
10
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
Changing LAN Settings
All settings for the internal LAN setup of the Router can be viewed and
changed here.
1. IP Address
The “IP address” is the internal IP address of the Router. The default
IP address is “192.168.2.1”. To access the advanced setup interface,
type this IP address into the address bar of your browser. This address
can be changed if needed. To change the IP address, type in the new
IP address and click “Apply Changes”. The IP address you choose
should be a non-routable IP. Examples of a non-routable IP are:
192.168.x.x (where x is anything between 0 and 255)
10.x.x.x (where x is anything between 0 and 255)
2. Subnet Mask
There is no need to change the subnet mask. This is a unique,
advanced feature of your Belkin Router. It is possible to change the
subnet mask if necessary; however, do NOT make changes to the
subnet mask unless you have a specific reason to do so. The default
setting is “255.255.255.0”.
3. DHCP Server
The DHCP server function makes setting up a network very easy
by assigning IP addresses to each computer on the network
automatically. The default setting is “On”. The DHCP server can be
turned OFF if necessary; however, in order to do so you must manually
set a static IP address for each computer on your network. To turn off
the DHCP server, select “Off” and click “Apply Changes”.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
4. IP Pool
The range of IP addresses set aside for dynamic assignment to the
computers on your network. The default is 2–100 (99 computers). If
you want to change this number, you can do so by entering a new
starting and ending IP address and clicking on “Apply Changes”. The
DHCP server can assign 100 IP addresses automatically. This means
that you cannot specify an IP address pool larger than 100 computers.
For example, starting at 50 means you have to end at 150 or lower so
as not to exceed the 100-client limit. The starting IP address must be
3
4
lower in number than the ending IP address.
5
5. Lease Time
6
The length of time the DHCP server will reserve the IP address for
each computer. We recommend that you leave the lease time set to
“Forever”. The default setting is “Forever”, meaning that any time
a computer is assigned an IP address by the DHCP server, the IP
address will not change for that particular computer. Setting lease
times for shorter intervals such as one day or one hour frees IP
addresses after the specified period of time. This also means that a
particular computer’s IP address may change over time. If you have set
any of the other advanced features of the Router such as DMZ or client
IP filters, these are dependent on the IP address. For this reason, you
will not want the IP address to change.
7
8
9
10
6. Local Domain Name
The default setting is “Belkin”. You can set a local domain name
(network name) for your network. There is no need to change this
setting unless you have a specific advanced need to do so. You can
name the network anything you want such as “MY NETWORK”.
Viewing the DHCP Client List Page
You can view a list of the computers (known as clients), which are
connected to your network. You are able to view the IP address (1) of
the computer, the host name (2) (if the computer has been assigned
one), and the MAC address (3) of the computer’s network interface
card (NIC). Pressing the “Refresh” (4) button will update the list. If
there have been any changes, the list will be updated.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
Configuring the Wireless Network Settings
The “Wireless” tab lets you make changes to the wireless network
settings. From this tab you can make changes to the wireless network
name or Service Set Identifier (SSID), operating channel, encryption
security settings, and configure the Router to be used as an access
point.
Wi-Fi® Multimedia (WMM®) Settings
Enabling the WMM allows you to prioritize the data packets of your
network. The prioritization categories are voice, video, best effort,
and background. A WMM-enabled device delivers scheduled access.
It reserves network resources based on the 802.1d tags of Wi-Fi
multimedia applications.
Voice
6,7
4,5
0,3
1,2
Highest
Lowest
Video
Best Effort
Background
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
Changing the Wireless Network Name (SSID)
To identify your wireless network, a name called the SSID is used.
The SSID is your network name. The default network name of the
Router is “Belkin Wireless G Plus MIMO”. Your network name will look
something like “Belkin_G Plus_MIMO_ADSL”. You can change this to
anything you choose, or you can leave it unchanged. Keep in mind, if
you decide to change your wireless network name, and there are other
wireless networks operating in your area, your network name needs to
be different from other wireless networks that may be operating in your
area. To change the SSID, type in the SSID that you want to use in the
SSID field (1) and click “Apply Changes” (2). The change is immediate.
If you make a change to the SSID, your wireless-equipped computers
may also need to be reconfigured to connect to your new network
name. Refer to the documentation of your wireless network adapter for
information on making this change.
3
4
5
6
7
Note: Please periodically check for new Router firmware updates
from the “Utilities > Firmware update” page. Newer firmware can fix
problems, add wireless features, and/or improve wireless performance
(see page 51).
8
9
10
Changing the Wireless Channel
There are a number of operating channels from which you can
choose—in the United Kingdom (and most of Europe) and Australia,
there are 13. In other countries, there are other channel requirements.
Your Router is configured to operate on the proper channels for the
country in which you reside. The channel can be changed if needed. If
there are other wireless networks operating in your area, your network
should be set to operate on a channel that is different than the other
wireless networks.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
Using the Wireless Mode Switch
This switch allows you to set the Router’s wireless modes. There are
several modes.
Note: Some modes may require firmware updates to be enabled.
1) 802.11g + 802.11b
Setting the Router to this mode will allow 802.11g- and 802.11b-
compliant devices to join the network. 802.11g devices will operate at
the 802.11b speed only
2) 802.11g only
Setting the Router to this mode will allow only 802.11g-compliant
devices to join the network, keeping out 802.11b devices.
Using the Broadcast SSID Feature
Note: This advanced feature should be employed by advanced users
only. For security, you can choose not to broadcast your network’s
SSID. Doing so will keep your network name hidden from computers
that are scanning for the presence of wireless networks. To turn off
the broadcast of the SSID, remove the check mark from the box next
to “Broadcast SSID”, and then click “Apply Changes”. The change is
immediate. Each computer now needs to be set to connect to your
specific SSID; an SSID of “ANY” will no longer be accepted. Refer to
the documentation of your wireless network adapter for information on
making this change.
Changing the Wireless Security Settings
Your Router is equipped with the latest security standard called Wi-Fi
Protected Access™ 2 (WPA2™). It also supports the legacy security
standard called Wired Equivalent Privacy (WEP). By default, wireless
security is disabled. To enable security, you will need to determine
which standard you want to use. To access the security settings, click
“Security” on the “Wireless” tab.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
3
4
5
The Router features WPA2, which is the second generation of the WPA™-
based 802.11i standard. It offers a higher level of wireless security by
combining advanced network authentication and stronger Advanced
Encryption Standard (AES) encryption methods.
6
7
WPA2 Requirements
IMPORTANT: In order to use WPA2 security, all your computers and
wireless client adapters must be upgraded with patches, driver, and client
utility software that supported WPA2. At the time of this User Manual’s
publication, a couple security patches are available, for free download,
from Microsoft®. These patches work only with the Windows XP operating
system. Other operating systems are not supported at this time.
8
9
10
For Windows XP computers that do not have Service Pack 2 (SP2), a file
from Microsoft called “Windows XP Support Patch for Wireless Protected
microsoft.com/?kbid=826942
For Windows XP with Service Pack 2, Microsoft has released a free
download to update the wireless client components to support WPA2
default.aspx?scid=kb;en-us;893357
IMPORTANT: You also need to ensure that all your wireless client cards/
adapters support WPA2, and that you have downloaded and installed
the latest driver. Most of the Belkin wireless cards have driver updates
networking.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
Setting WPA/WPA2-Personal (PSK)
Like WPA security, WPA2 is available in both WPA2-Personal (PSK)
mode and WPA2-Enterprise (RADIUS) mode. Typically, WPA2-Personal
(PSK) is the mode that will be used in a home environment, while
WPA2-Enterprise (RADIUS) is implemented in a business environment
where an external radius server distributes the network key to the
clients automatically. This guide will focus on WPA2-Personal (PSK)
usage. Please refer to the User Manual for more information about
wireless security and different types of wireless security.
1. After you’ve set up your Router, go to the “Security” page under
“Wireless” and select “WPA/WPA2-Personal (PSK)” from the “Security
Mode” drop-down menu.
2. For “Authentication”, select “WPA-PSK”, “WPA2-PSK”, or “WPA-
PSK + WPA2-PSK”. This setting will have to be identical on the
wireless clients that you set up. “WPA-PSK + WPA2-PSK” mode
will allow the Router to support clients running either WPA or WPA2
security.
3. For “Encryption Technique”, select “TKIP”, “AES”, or “TKIP+AES”.
This setting will have to be identical on the wireless clients that you set
up.
4. Enter your pre-shared key (PSK). This can be from eight to 63
characters and can be letters, numbers, or symbols. This same
key must be used on all of the wireless clients that you set up. For
example, your PSK might be something like: “Smith family network
key”. Click “Apply Changes” to finish. You must now set all wireless
clients to match these settings.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
IMPORTANT: Make sure your wireless computers are updated to work
with WPA2 and have the correct settings to get proper connection to
the Router.
3
Setting WPA Security
Note: To use WPA security, your wireless network cards must be
equipped with software that supports WPA. At the time this User
Manual was published, a security patch from Microsoft is available for
free download. This patch works only with Windows XP.
4
5
Your Router supports WPA-PSK (no server). WPA-PSK uses what is
known as a pre-shared key as the security key. A pre-shared key is
basically a password that is between eight and 39 characters long. It
can be a combination of letters, numbers, or characters. Each client
uses the same key to access the network. Typically this is the mode
that will be used in a home environment.
6
7
8
Setting WPA-PSK
9
1. From the “Security Mode” drop-down menu, select “WPA-PSK (no
server)”.
10
2. For “Encryption Technique”, select “TKIP” or “AES”. This setting will
have to be identical on the clients that you set up.
3. Enter your pre-shared key. This can be from eight to 39 characters
and can be letters, numbers, or symbols. This same key must be used
on all of the clients that you set up.
4. Click “Apply Changes” to finish. You must now set all clients to
match these settings.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
WPA-Enterprise (RADIUS) is a configuration wherein a radius server
distributes the keys to the clients automatically. This is typically used
in a business environment.
Setting WPA-Enterprise (RADIUS) Settings
If your network uses a radius server to distribute keys to the clients,
use this setting.
1. From the “Security Mode” drop-down menu, select “WPA/WPA2—
Enterprise (RADIUS)”.
2. Select “WPA-RADIUS” in the “Authentication” field.
3. In the “Encryption Technique” field, select “TKIP”. This setting will
have to be identical on the clients that you set up.
4. Enter the IP address of the radius server into the “Radius Server”
fields.
5. Enter the radius key into the “Radius Key” field.
6. Enter the key interval. Key interval is how often the keys are
distributed (in packets).
7. Click “Apply Changes” to finish. You must now set all clients to
match these settings.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
Setting WPA2-Enterprise (RADIUS) Settings
If your network uses a radius server to distribute keys to the clients,
use this setting.
1. From the “Security Mode” drop-down menu, select “WPA/WPA2—
Enterprise (RADIUS)”.
3
2. Select “WPA2-RADIUS” in the “Authentication” field.
3. In the “Encryption Technique” field, select “AES”. This setting will
have to be identical on the clients that you set up.
4
4. Enter the IP address of the radius server into the “Radius Server”
fields.
5
5. Enter the radius key into the “Radius Key” field.
6
6. Enter the key interval. Key interval is how often the keys are
distributed (in packets).
7
7. Click “Apply Changes” to finish. You must now set all clients to
match these settings.
8
9
10
Setting WEP Encryption
Note to Mac users: The “Passphrase” option will not operate with
Apple® AirPort®. To configure encryption for your Mac computer, set
the encryption using the manual method described in the next section.
1. Select “128-bit WEP” or “64-bit WEP” from the drop-down menu.
2. After selecting your WEP encryption mode, you can enter you WEP
key manually by typing in the hex WEP key manually, or you can type
a passphrase in the “PassPhrase” field and click “Generate” to create
a WEP key from the passphrase. Click “Apply Changes” to finish. You
must now set all of your clients to match these settings.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
3. Encryption in the Router is now set. Each of your computers on
your wireless network will now need to be configured with the same
passphrase. Refer to the documentation of your wireless network
adapter for information on making this change.
Using a Hexadecimal Key
A hexadecimal key is a mixture of numbers and letters from A–F and
0–9. 64-bit keys are 10 digits long and can be divided into five two-
digit numbers. 128-bit keys are 26 digits long and can be divided into
13 two-digit numbers.
For instance:
AF 0F 4B C3 D4 = 64-bit key
C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key
In the boxes below, make up your key by writing in two characters
between A–F and 0–9. You will use this key to program the encryption
settings on your Router and your wireless computers.
Note to Mac users: Original Apple AirPort products support 64-bit
encryption only. Apple AirPort 2 products can support 64-bit or 128-bit
encryption. Please check your product to see which version you are
using. If you cannot configure your network with 128-bit encryption, try
64-bit encryption.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
Wireless Bridge
Wireless bridging or Wireless Distribution System (WDS) is used to
connect wireless routers and access points (APs) together to extend a
network.
3
Click on the drop-down menu next to “Bridge Mode” to select either:
4
5
6
7
8
9
10
Disabled: To disable wireless bridging (default).
Manual: To enter the wireless MAC address(es) of the APs to which to
bridge, manually.
1. Wireless channels must match between the Router and AP.
2. Security settings (WEP) must match between the Router and AP.
3. If MAC filtering is enabled, the user must be sure to add the WLAN
MAC address(es) of the Router/AP in order to allow communication with
each other.
4. If using a network protected by WPA, the SSID on both APs must be
the same.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
Configuring the Firewall
Your Router is equipped with a firewall that will protect your network
from a wide array of common hacker attacks including:
•
•
•
•
•
•
•
•
•
•
•
•
IP Spoofing
Land Attack Ping of Death (PoD)
Denial of Service (DoS)
IP with zero length
Smurf Attack
TCP Null Scan
SYN flood
UDP flooding
Tear Drop Attack
ICMP defect
RIP defect
Fragment flooding
The firewall also masks common ports that are frequently used to
attack networks. These ports appear to be “stealth” meaning that for all
intents and purposes, they do not exist to a would-be hacker. You can
turn the firewall function off if needed; however, it is recommended that
you leave the firewall enabled. Disabling the firewall protection will not
leave your network completely vulnerable to hacker attacks, but it is
recommended that you leave the firewall enabled.
Configuring Internal Forwarding Settings
The Virtual Servers function will allow you to route external (Internet)
calls for services such as a web server (port 80), FTP server (Port 21),
or other applications through your Router to your internal network.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
Since your internal computers are protected by a firewall, computers
outside your network (over the Internet) cannot get to them because
they cannot be “seen”. A list of common applications has been
provided in case you need to configure the Virtual Server function for
a specific application. If your application is not listed, you will need to
contact the application vendor to find out which port settings you need.
3
4
5
6
7
8
9
Choosing an Application
Select your application from the drop-down list. Click “Add”. The
settings will be transferred to the next available space in the screen.
Click “Apply Changes” to save the setting for that application. To
remove an application, select the number of the row that you want to
remove then click “Clear”.
10
Manually Entering Settings into the Virtual Server
To manually enter settings, enter the IP address in the space provided
for the internal (server) machine, the port(s) required to pass (use a
comma between multiple ports), select the port type (TCP or UDP),
and click “Apply Changes”. You can only pass one port per internal IP
address. Opening ports in your firewall can pose a security risk. You
can enable and disable settings very quickly. It is recommended that
you disable the settings when you are not using a specific application.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
Setting Client IP Filters
The Router can be configured to restrict access to the Internet, e-mail,
or other network services at specific days and times. Restriction can be
set for a single computer, a range of computers, or multiple computers.
To restrict Internet access to a single computer for example, enter the
IP address of the computer you wish to restrict access to in the IP
fields (1). Next, enter “80” in both the port fields (2). Select “Both” (3).
Select “Block” (4). You can also select “Always” to block access all
of the time. Select the day to start on top (5), the time to start on top
(6), the day to end on the bottom (7), and the time to stop (8) on the
bottom. Select “Enable” (9). Click “Apply Changes”. The computer at
the IP address you specified will now be blocked from Internet access
at the times you specified. Note: Be sure you have selected the correct
time zone under “Utilities> System Settings> Time Zone”.
Setting MAC-Address Control
The MAC-address filter is a powerful security feature that allows you
to specify which computers are allowed on the network. Any computer
attempting to access the network that is not specified in the filter list
will be denied access. When you enable this feature, you must enter a
name for the user and the MAC address of each client on your network
to allow network access. Next, click “Add” to save the settings.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
3
4
Enabling the Demilitarized Zone (DMZ)
5
The DMZ feature allows you to specify one computer on your network
to be placed outside of the firewall. This may be necessary if the
firewall is causing problems with an application such as a game or
video conferencing application. Use this feature on a temporary basis.
The computer in the DMZ is NOT protected from hacker attacks.
6
7
8
9
10
To put a computer in the DMZ, enter the last digits of its IP address in
the IP field and select “Enable”. Click “Apply Changes” for the change
to take effect. If you are using multiple static WAN IP addresses, it is
possible to select which WAN IP address the DMZ host will be directed
to. Type in the WAN IP address you wish the DMZ host to direct to,
enter the last two digits of the IP address of the DMZ host computer,
select “Enable” and click “Apply Changes”.
Blocking an ICMP Ping
Computer hackers use what is known as “pinging” to find potential
victims on the Internet. By pinging a specific IP address and receiving
a response from the IP address, a hacker can determine that something
of interest might be there. The Router can be set up so it will not
respond to an ICMP ping from the outside. This heightens your
Router’s security level.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
To turn off the ping response, select “Block ICMP Ping” (1) and click
“Apply Changes”. The Router will not respond to an ICMP ping.
Security Log
The security log shows detailed system-monitoring information. Users
can click the “Save” button to store the log as a text file for later
reference purposes. The “Refresh” button refreshes the page with any
new logs and the “Clear” button clears the page of any existing logs.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
Utilities
The “Utilities” screen lets you manage different parameters of the Router
and perform certain administrative functions.
3
4
5
6
7
Restarting the Router
Sometimes it may be necessary to restart or reboot the Router if it begins
working improperly. Restarting or rebooting the Router will NOT delete
any of your configuration settings.
8
9
10
Restarting the Router to Restore Normal Operation
1. Click the “Restart Router” button.
2. The following message will appear. Click “OK”.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
3. The following message will appear. Restarting the Router can take
up to 60 seconds. It is important not to turn off the power to the
Router during the restart.
4. A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router will be restarted. The Router home
page should appear automatically. If not, type in the Router’s address
(default = 192.168.2.1) into the navigation bar of your browser.
Restoring Factory Default Settings
Using this option will restore all of the settings in the Router to the
factory (default) settings. It is recommended that you back up your
settings before you restore all of the defaults.
1. Click the “Restore Defaults” button.
2. The following message will appear. Click “OK”.
3. The following message will appear. Restoring the defaults includes
restarting the Router. It can take up to 60 seconds. It is important not
to turn the power to the Router off during the restart.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
4. A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router’s defaults will be restored. The
Router home page should appear automatically. If it does not, type in
the Router’s address (default = 192.168.2.1) into the navigation bar of
your browser.
3
Saving a Current Configuration
You can save your current configuration by using this feature. Saving
your configuration will allow you to restore it later if your settings are
lost or changed. It is recommended that you back up your current
configuration before performing a firmware update.
4
5
6
7
8
1. Click “Save”. A window called “File Download” will open. Click
“Save”.
9
10
2. A window will open that allows you to select the location where you
want to save the configuration file. Select a location. You can name
the file anything you want, or use the default name “Config”. Be sure
to name the file so you can locate it yourself later. When you have
selected the location and name of the file, click “Save”.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
3. When the save is complete, you will see the window below. Click
“Close”.
The configuration is now saved.
Restoring a Previous Configuration
This option will allow you to restore a previously saved configuration.
1. Click “Browse”. A window will open that allows you to select the
location of the configuration file. All configuration files end with a “.bin”.
Locate the configuration file you want to restore and double-click on it.
2. You will be asked if you want to continue. Click “OK”.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
3. A reminder window will appear. It will take up to 60 seconds for the
configuration restoration to complete. Click “OK”.
3
4
4. A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router’s configuration will be restored.
The Router’s home page should appear automatically. If not, type in
the Router’s address (default = 192.168.2.1) into the navigation bar of
your browser.
5
6
7
Updating the Firmware
From time to time, Belkin may release new versions of the Router’s
firmware. Firmware updates contain feature improvements and fixes to
problems that may have existed. When Belkin releases new firmware,
you can download the firmware from the Belkin update website and
update your Router’s firmware to the latest version.
8
9
10
Checking for a New Version of Firmware
The “Check Firmware” (1) button allows you to instantly check for a
new version of firmware. When you click the button, a new browser
window will appear informing you that either no new firmware is
available or that there is a new version available. If a new version is
available, you will have the option to download it.
Downloading a New Version of Firmware
If you click the “Check Firmware” button and a new version of
firmware is available, you will see a screen similar to the one below:
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1. To download the new version of firmware, click “Download”.
A window will open that allows you to select the location where you
want to save the firmware file. Select a location. You can name the file
anything you want, or use the default name. Be sure to locate the file in
a place where you can locate it yourself later. When you have selected
the location, click “Save”.
2. When the save is complete, you will see the following window. Click
“Close”.
3. The download of the firmware is complete. To update the firmware,
follow the next steps in “Updating the Router’s Firmware”.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
Updating the Router’s Firmware
1. In the “Firmware Update” page, click “Browse”. A window will open
that allows you to select the location of the firmware update file.
3
4
5
6
7
2. Browse to the firmware file you downloaded. Select the file by
double-clicking on the file name.
8
The “Update Firmware” box will now display the location and name of
the firmware file you just selected. Click “Update”.
9
10
3. You will be asked if you are sure you want to continue. Click “OK”.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
4. You will see one more message. This message tells you that the
Router may not respond for as long as one minute as the firmware is
loaded into the Router and the Router is rebooted. Click “OK”.
5. A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router firmware update will be complete.
The Router home page should appear automatically. If not, type in the
Router’s address (default = 192.168.2.1) into the navigation bar of your
browser.
Changing System Settings
The “System Settings” page is where you can enter a new
administrator password, set the time zone, enable remote
management, and turn on and off the NAT function of the Router.
Setting or Changing the Administrator Password
The Router ships with NO password entered. If you wish to add a
password for greater security, you can set a password here. Write
down your password and keep it in a safe place, as you will need it if
you need to log into the Router in the future. It is also recommended
that you set a password if you plan to use the remote management
feature of your Router.
C
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
The login time-out option allows you to set the period of time that you
can be logged into the Router’s advanced setup interface. The timer
starts when there has been no activity. For example, imagine you have
made some changes in the advanced setup interface, then left your
computer alone without clicking “Logout”. Assuming the time-out is set
to 10 minutes, 10 minutes after you leave, the login session will expire.
You will have to log into the Router again to make any more changes.
The login time-out option is for security purposes and the default is
set to 10 minutes. Note: Only one computer can be logged into the
Router’s advanced setup interface at one time.
3
4
5
Setting the Time and Time Zone
6
The Router keeps time by connecting to a Simple Network Time
Protocol (SNTP) server. This allows the Router to synchronize the
system clock to the global Internet. The synchronized clock in the
Router is used to record the security log and control client filtering.
Select the time zone that you reside in. You have the option to select
a primary and a backup NTP server to keep your Router’s clock
synchronized. Select your desired NPT server from the drop-down box,
or simply keep it as is.
7
8
9
If you reside in an area that observes daylight saving, then place a
check mark in the box next to “Enable Daylight Saving”. The system
clock may not update immediately. Allow at least 15 minutes for the
Router to contact the time servers on the Internet and get a response.
You cannot set the clock yourself.
10
Enabling Remote Management
Before you enable this advanced feature of your Belkin Router, MAKE
SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote
management allows you to make changes to your Router’s settings
from anywhere on the Internet. There are two methods of remotely
managing the Router. The first is to allow access to the Router from
anywhere on the Internet by selecting “Any IP address can remotely
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
manage the Router”. By typing in your WAN IP address from any
computer on the Internet, you will be presented with a login screen
where you need to type in the password of your Router.
The second method is to allow a specific IP address only to remotely
manage the Router. This is more secure, but less convenient. To use
this method, enter the IP address you know you will be accessing the
Router from in the space provided and select “Only this IP address
can remotely manage the Router”. Before you enable this function, it is
STRONGLY RECOMMENDED that you set your administrator password.
Leaving the password empty will potentially open your Router to
intrusion.
Advanced Feature: The “Remote Access Port” option allows you to
configure the desired “Remote Access Port for Remote Management”
feature. The default access port is set to port 80.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web-Based Advanced User Interface
1
2
Enabling/Disabling UPnP
UPnP (Universal Plug-and-Play) is yet another advanced feature offered
by your Belkin Router. It is a technology that offers seamless operation
of voice messaging, video messaging, games, and other applications
that are UPnP-compliant. Some applications require the Router’s
firewall to be configured in a specific way to operate properly. This
usually requires opening TCP and UDP ports, and in some instances,
setting trigger ports. An application that is UPnP-compliant has the
ability to communicate with the Router, basically “telling” the Router
which way it needs the firewall configured. The Router ships with the
UPnP feature disabled. If you are using any applications that are UPnP-
compliant, and wish to take advantage of the UPnP features, you can
enable the UPnP feature. Simply select “Enable” in the “UPnP Enabling”
section of the “Utilities” page. Click “Apply Changes” to save the
change.
3
4
5
6
7
8
9
10
Enabling/Disabling Auto Firmware Update
This innovation provides the Router with the built-in capability to
automatically check for a new version of firmware and alert you that
the new firmware is available. When you log into the Router’s advanced
interface, the Router will perform a check to see if new firmware is
available. If so, you will be notified. You can choose to download the
new version or ignore it.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Manually Configuring Network Settings
Manually Configuring Network Settings
Set up the computer that is connected to the cable or DSL modem
FIRST using these steps. You can also use these steps to add
computers to your Router after the Router has been set up to connect
to the Internet.
Manually Configuring Network Settings in Mac OS up to 9.x
1. Pull down the Apple menu. Select “Control Panels” and select
“TCP/IP”.
2. You will see the TCP/IP control panel. Select “Ethernet Built-In” or
“Ethernet” in the “Connect via:” drop-down menu (1).
3. Next to “Configure” (2), if “Manually” is selected, your Router will
need to be set up for a static IP connection type. Write the address
information in the table below. You will need to enter this information
into the Router.
4. If not already set, at “Configure:”, choose “Using DHCP Server”.
This will tell the computer to obtain an IP address from the Router.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Manually Configuring Network Settings
1
2
5. Close the window. If you made any changes, the following window
will appear. Click “Save”.
3
4
Restart the computer. When the computer restarts, your network
settings are now configured for use with the Router.
5
6
Manually Configuring Network Settings in Mac OS X
1. Click on the “System Preferences” icon.
7
8
2. Select “Network” (1) from the “System Preferences” menu.
9
10
3. Select “Built-in Ethernet” (2) next to “Show” in the Network menu.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Manually Configuring Network Settings
4. Select the “TCP/IP” tab (3). Next to “Configure” (4), you should see
“Manually” or “Using DHCP”. If you do not, check the PPPoE tab (5)
to make sure that “Connect using PPPoE” is NOT selected. If it is, you
will need to configure your Router for a PPPoE connection type using
your user name and password.
5. If “Manually” is selected, your Router will need to be set up for a
static IP connection type. Write the address information in the table
below. You will need to enter this information into the Router.
6. If not already selected, select “Using DHCP” next to “Configure” (4),
then click “Apply Now”.
Your network settings are now configured for use with the Router.
Manually Configuring Network Settings in Windows 2000, NT, or XP
1. Click “Start”, “Settings”, then “Control Panel”.
2. Double-click on the “Network and dial-up connections” icon
(Windows 2000) or the “Network” icon (Windows XP).
3. Right-click on the “Local Area Connection” associated with your
network adapter and select “Properties” from the drop-down menu.
4. In the “Local Area Connection Properties” window, click “Internet
Protocol (TCP/IP)” and click the “Properties” button. The following
screen will appear:
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Manually Configuring Network Settings
1
2
5. If “Use the following IP address” (2) is selected, your Router will
need to be set up for a static IP connection type. Write the address
information the table below. You will need to enter this information into
the Router.
3
4
5
6
6. If not already selected, select “Obtain an IP address automatically”
(1) and “Obtain DNS server address automatically” (3). Click “OK”.
7
Your network settings are now configured for use with the Router.
8
Manually Configuring Network Settings in Windows 98 or Me
9
1. Right-click on “My Network Neighborhood” and select “Properties”
from the drop-down menu.
10
2. Select “TCP/IP -> settings” for your installed network adapter. You
will see the following window.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Manually Configuring Network Settings
3. If “Specify and IP address” is selected, your Router will need to be
set up for a static IP connection type. Write the address information in
the table below. You will need to enter this information into the Router.
4. Write the IP address and subnet mask from the “IP Address” tab (3).
5. Click the “Gateway” tab (2). Write the gateway address down in the
chart.
6. Click the “DNS Configuration” tab (1). Write the DNS address(es) in
the chart.
7. If not already selected, select “Obtain IP address automatically” on
the IP address tab. Click “OK”.
Restart the computer. When the computer restarts, your network
settings are now configured for use with the Router.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended Web Browser settings
1
2
Recommended Web Browser Settings
In most cases, you will not need to make any changes to your web
browser’s settings. If you are having trouble accessing the Internet or
the Web-Based Advanced User Interface, then change your browser’s
settings to the recommended settings in this section.
3
Microsoft® Internet Explorer 4.0 or Higher
4
1. Start your web browser. Select “Tools” then “Internet Options”.
5
6
7
8
9
10
2. In the “Internet Options” screen, there are three selections: “Never
dial a connection”, “Dial whenever a network connection is not
present”, and “Always dial my default connection”. If you can make
a selection, select “Never dial a connection”. If you cannot make a
selection, go to the next step.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended Web Browser settings
3. Under the “Internet Options” screen, click on “Connections” and
select “LAN Settings…”.
4. Make sure there are no check marks next to any of the displayed
options: “Automatically detect settings”, “Use automatic configuration
script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in
the “Internet Options” page.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended Web Browser settings
1
2
Netscape® Navigator® 4.0 or Higher
1. Start Netscape. Click on “Edit” then “Preferences”.
2. In the “Preferences” window, click on “Advanced” then select
“Proxies”. In the “Proxies” window, select “Direct connection to the
Internet”.
3
4
5
6
7
8
9
10
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem:
Setup Assistant CD does not automatically start.
Solution:
If the CD-ROM does not start the Setup Assistant automatically, it
could be that the computer is running other applications that are
interfering with the CD drive.
1. If the Setup Assistant Welcome screen does not appear within 15-
20 seconds, open up your CD-ROM drive by double-clicking on the
“My Computer” icon that is located on your desktop.
2. Next, double-click on the CD-ROM drive that the Setup Assistant
CD has been placed in to start the installation.
3. The Setup Assistant should start within a few seconds. If, instead,
a window appears showing the files on the CD, double-click on the
icon labeled “SetupAssistant”.
4. If the Setup Assistant still does not start, reference the section
titled “Manually Configuring Network Settings” (page 62) of this
User Manual for an alternative setup method).
Problem:
Setup Assistant cannot find my Router.
Solution:
If the Setup Assistant is not able to find the Router during the
installation process, please check the following items:
1. If the Setup Assistant is not able to find the Router during the
installation process, there may be third-party firewall software
installed on the computer attempting to access the Internet.
Examples of third-party firewall software are ZoneAlarm, BlackICE
PC Protection, McAfee Personal Firewall, and Norton Personal
Firewall. If you do have firewall software installed on your
computer, please make sure that you properly configure it. You
can determine if the firewall software is preventing Internet access
by temporarily turning it off. If, while the firewall is disabled,
Internet access works properly, you will need to change the firewall
settings to function properly when it is turned on. Please refer to
the instructions provided by the publisher of your firewall software
for instructions on configuring the firewall to allow Internet access.
2. Unplug power to the Router for 10 seconds, and then plug the
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1
2
power back into the Router. Ensure that the Router’s “Power”
LED is on; it should be solid GREEN. If not, check to make sure
that the AC adapter is connected to the Router and plugged into
a wall outlet
3. Ensure that you have a cable connected between (1) the
network (Ethernet) port on the back of the computer and (2) one
of the “Connections to your computers” ports on the back of the
Router.
3
4
Note: The computer should NOT be connected to the port
labeled “DSL Line” on the back of the Router.
5
4. Try shutting down and restarting your computer, then rerunning
the Setup Assistant.
6
If the Setup Assistant is still unable to find the Router, reference
the section titled “Manually Configuring Network Settings” for
installation steps.
7
Problem:
8
Setup Assistant cannot connect my Router to the Internet.
Solution:
9
If the Setup Assistant is not able to connect the Router to the
Internet, please check the following items:
10
1. Use the troubleshooting suggestions within the Setup Assistant.
2. If your ISP requires a user name and password, make sure that
you have typed in your user name and password correctly.
Some user names require that the ISP’s domain may be at
the end of the name. Example: “myname@myisp.com”. The
“@myisp.com” part of the user name may need to be typed as
well as your user name.
If you continue to have no Internet connection, reference the
section titled “Manually Configuring Network Settings” (page xx of
this User Manual for an alternative setup method).
Problem:
•
The Setup Assistant completed installation, but my web browser
doesn’t work.
•
I am unable to connect to the Internet. The “ADSL” LED on my
Router is off, and the “Internet” LED is blinking.
Solution:
If you cannot connect to the Internet, and the “ADSL” LED is off,
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
and the “Internet” LED is blinking, the problem may be that your
modem and Router are not connected properly.
1. Make sure the network cable between the modem and the
Router is connected. The cable should be connected at one
end to the Router’s “DSL Line” port, and at the other end to the
network port on your modem.
2. Unplug the cable or DSL modem from its power source for three
minutes. After three minutes, plug the modem back into its
power source. This may force the modem to properly recognize
the Router.
3. Unplug the power to your Router, wait 10 seconds, and then
reconnect the power. This will cause the Router to reattempt
communication with the modem. If the “ADSL” LED on the
Router is not lit after completing these steps, please contact
Belkin Technical Support.
4. Try shutting down and restarting your computer.
Problem:
•
•
The Setup Assistant completed installation, but my web browser
doesn’t work.
I am unable to connect to the Internet. The “ADSL” LED on my
Router is on, and the “Internet” LED is blinking.
Solution:
1. If you cannot connect to the Internet, the “ADSL” LED is on,
and the “Internet” LED is blinking, the problem may be that your
connection type may not match the ISP’s connection.
2. If you have a “static IP address” connection, your ISP must
assign you the IP address, subnet mask, and gateway address.
Please refer to the section entitled “Alternate Setup Method” for
details on changing this setting.
3. If you have a “PPPoE” connection, your ISP will assign you a
user name and password and sometimes a service name. Make
sure the Router’s connection type is configured to PPPoE and
the settings are entered properly. Please refer to the section
entitled “Alternate Setup Method” for details on changing this
setting.
4. You may need to configure your Router to meet the specific
requirements of your ISP. To search our knowledge base for
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1
2
type in “ISP”.
If you are still unable to access the Internet after verifying these
settings, please contact Belkin Technical Support.
Problem:
3
•
The Setup Assistant completed, but my web browser doesn’t work.
•
I am unable to connect to the Internet. The “ADSL” LED on my
Router is blinking, and the “Internet” LED is solid.
4
Solution:
5
1. If the “ADSL” LED is blinking, and the “Internet” LED is solid,
but you are unable to access the Internet, there may be third-
party firewall software installed on the computer attempting to
access the Internet. Examples of third-party firewall software are
ZoneAlarm, BlackICE PC Protection, McAfee Personal Firewall,
and Norton Personal Firewall.
6
7
2. If you do have firewall software installed on your computer,
please make sure that you properly configure it. You can
determine if the firewall software is preventing Internet access
by temporarily turning it off. If, while the firewall is disabled,
Internet access works properly, you will need to change the
firewall settings to function properly when it is turned on.
8
9
3. Please refer to the instructions provided by the publisher of your
firewall software for instructions on configuring the firewall to
allow Internet access.
10
If you are still unable to access the Internet after disabling any
firewall software, please contact Belkin Technical Support.
Problem:
I can’t connect to the Internet wirelessly.
Solution:
If you are unable to connect to the Internet from a wireless
computer, please check the following items:
1. Look at the lights on your Router. If you’re using a Belkin Router,
the lights should be as follows:
• The “Power” LED should be on.
• The “ADSL” LED should be on, and not blinking.
• The “Internet” LED should be on, and not blinking.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
* The “WLAN Status” LED should be on, not blinking.
2. Open your wireless utility software by clicking on the icon in the
system tray at the bottom, right-hand corner of the screen.
3. The exact window that opens will vary depending on the model
of wireless card you have; however, any of the utilities should
have a list of “Available Networks”—those wireless networks it
can connect to.
Does the name of your wireless network appear in the results?
Yes, my network name is listed—go to the troubleshooting solution
titled “I can’t connect to the Internet wirelessly, but my network
name is listed”.
No, my network name is not listed—go to the troubleshooting
solution titled “I can’t connect to the Internet wirelessly, and my
network name is not listed”.
Problem:
I can’t connect to the Internet wirelessly, but my network name is
listed.
Solution:
If the name of your network is listed in the “Available Networks” list,
please follow the steps below to connect wirelessly:
1. Click on the correct network name in the “Available Networks”
list.
2. If the network has security (encryption) enabled, you will need to
enter the network key. For more information regarding security,
see the section entitled “Changing the Wireless Security
Settings”.
3. Within a few seconds, the tray icon in the lower, left-hand corner
of your screen should turn green, indication of a successful
connection to the network.
Problem:
I can’t connect to the Internet wirelessly, and my network name is
not listed.
Solution:
If the correct network name is not listed under “Available Networks”
in the wireless utility, please attempt the following troubleshooting
steps:
1. Temporarily move computer, if possible, five to 10 feet from the
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1
2
Router. Close the wireless utility, and reopen it. If the correct
network name now appears under “Available Networks”, you
may have a range or interference problem. Please see the
suggestions discussed in the section titled “Placement of your
Wireless G Plus MIMO ADSL2+ Modem Router” of this User
Manual.
3
2. Using a computer that is connected to the Router via a network
cable (as opposed to wirelessly), ensure that “Broadcast SSID”
is enabled. This setting is found on the Router’s wireless
“Channel and SSID” configuration page.
4
5
If you are still unable to access the Internet after completing these
steps, please contact Belkin Technical Support.
6
Problem:
•
•
•
•
My wireless network performance is inconsistent.
Data transfer is sometimes slow.
Signal strength is poor.
7
8
Difficulty establishing and/or maintaining a Virtual Private Network
(VPN) connection.
9
Solution:
Wireless technology is radio-based, which means connectivity and
the throughput performance between devices decreases when
the distance between devices increases. Other factors that will
cause signal degradation (metal is generally the worst culprit) are
obstructions such as walls and metal appliances. Note also that
connection speed may decrease as you move farther away from the
Router.
10
In order to determine if wireless issues are related to range, we
suggest temporarily moving the computer, if possible, five to 10 feet
from the Router.
Changing the wireless channel—Depending on local wireless traffic
and interference, switching the wireless channel of your network
can improve performance and reliability. The default channel the
Router is shipped with is channel 11; you may choose from several
other channels depending on your region. See the section on page
XX [insert the correct pg no.] entitled “Changing the Wireless
Channel” for instructions on how to choose other channels.
Limiting the wireless transmit rate—Limiting the wireless
transmit rate can help improve the maximum wireless range and
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
connection stability. Most wireless cards have the ability to limit
the transmission rate. To change this property, go to the Windows
Control Panel, open “Network Connections” and double-click on
your wireless card’s connection. In the properties dialog, select
the “Configure” button on the “General” tab (Windows 98 users
will have to select the wireless card in the list box and then click
“Properties”), then choose the “Advanced” tab and select the rate
property.
Wireless client cards are usually set to automatically adjust the
wireless transmit rate for you, but doing so can cause periodic
disconnects when the wireless signal is too weak; as a rule, slower
transmission rates are more stable. Experiment with different
connection rates until you find the best one for your environment.
Note that all available transmission rates should be acceptable for
browsing the Internet. For more assistance, see your wireless card’s
user manual.
Problem:
I am having difficulty setting up Wired Equivalent Privacy (WEP)
security on my Belkin Router.
Solution:
1. Log into your Router.
Open your web browser and type in the IP address of the Router.
(The Router’s default is 192.168.2.1.) Log into your Router by
clicking on the “Login” button in the top right-hand corner of the
screen. You will be asked to enter your password. If you never set a
password, leave the “Password” field blank and click “Submit”.
Click the “Wireless” tab on the left of your screen. Select the
“Encryption” or “Security” tab to get to the security settings page.
2.Select “128-bit WEP” from the drop-down menu.
3. After selecting your WEP encryption mode, you can type in your
hex WEP key manually, or you can type in a passphrase in the
“Passphrase” field and click “Generate” to create a WEP key
from the passphrase. Click “Apply Changes” to finish. You
must now set all of your clients to match these settings. A hex
(hexadecimal) key is a mixture of numbers and letters from A-F
and 0-9. For 128-bit WEP, you need to enter 26 hex keys.
For example:
C3 03 0F AF 4B B2 C3 D4 4B C3 D4 E7 E4 = 128-bit key
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1
2
4.Click “Apply Changes” to finish. Encryption in the Router is now
set. Each of your computers on your wireless network will now
need to be configured with the same security settings.
WARNING: If you are configuring the Router from a computer with
a wireless client, you will need to ensure that security is turned on
for this wireless client. If this is not done, you will lose your wireless
connection.
3
4
Note to Mac Users: Original Apple AirPort products support 64-
bit encryption only. Apple AirPort 2 products can support 64-bit or
128-bit encryption. Please check your Apple AirPort product to see
which version you are using. If you cannot configure your network
with 128-bit encryption, try 64-bit encryption.
5
6
Problem:
7
I am having difficulty setting up Wired Equivalent Privacy (WEP)
security on a Belkin client card.
8
Solution:
The client card must use the same key as the Router. For instance,
if your Router uses the key 00112233445566778899AABBCC, then
the client card must be set to the exact same key.
9
10
1. Double-click the Signal Indicator icon to bring up the “Wireless
Network” screen.
2. The “Advanced” button will allow you to view and configure more
options of your card.
3. Once the “Advanced” button is clicked, the Belkin Wireless LAN
Utility will appear. This Utility will allow you to manage all the
advanced features of the Belkin Wireless Card.
4. Under the “Wireless Network Properties” tab, select a network
name from the “Available Networks” list and click the
“Properties” button.
5. Under “Data Encryption”, select “WEP”.
6. Ensure that the check box “The key is provided for me
automatically” at the bottom is unchecked. If you are using this
computer to connect to a corporate network, please consult
your network administrator if this box needs to be checked.
7. Type your WEP key in the “Network key” box.
Important: A WEP key is a mixture of numbers and letters from A-F
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
and 0-9. For 128-bit WEP, you need to enter 26 keys. This network
key needs to match the key you assign to your Router.
For example:
C3 03 0F AF 4B B2 C3 D4 4B C3 D4 E7 E4 = 128-bit key
8. Click “OK”, and then “Apply” to save the settings.
If you are not using a Belkin wireless client card, please consult the
manufacturer’s user manual for that wireless client card.
Problem:
Do Belkin products support WPA?
Solution:
Note: To use WPA security, all your clients must be upgraded
to drivers and software that support it. At the time of this FAQ
publication, a security patch download is available, for free, from
Microsoft. This patch works only with the Windows XP operating
system.
You also need to download the latest driver for your Belkin 802.11g
Wireless Desktop or Notebook Network Card from the Belkin
support site. Other operating systems are not supported at this
time. Microsoft’s patch only supports devices with WPA-enabled
drivers such as Belkin 802.11g products.
the following products:
F5D7000, F5D7001, F5D7010, F5D9010, F5D9050, F5D7230-4,
F5D7231-4, F5D7130, F5D9230-4
Problem:
I am having difficulty setting up Wireless Protected Access (WPA)
security on my Belkin Router for a home network.
Solution:
1. From the “Security Mode” drop-down menu, select “WPA-PSK
(no server)”.
2. For “Encryption Technique”, select “TKIP” or “AES”. This setting
will have to be identical on the clients that you set up.
3. Enter your pre-shared key. This can be from eight to 63
characters and can be letters, numbers, symbols, or spaces.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1
2
This same key must be used on all of the clients that you set up.
For example, your PSK might be something like: “Smith family
network key”.
4. Click “Apply Changes” to finish. You must now set all clients to
match these settings.
3
Problem:
I am having difficulty setting up Wireless Protected Access (WPA)
security on a Belkin wireless client card for a home network.
4
Solution:
5
Clients must use the same key that the Router uses. For instance,
if the key is “Smith Family Network Key” in the Router, the clients
must also use that same key.
6
1. Double-click the Signal Indicator icon to bring up the “Wireless
Network” screen. The “Advanced” button will allow you to view
and configure more options of your card.
7
2. Once the “Advanced” button is clicked, the Belkin Wireless
Utility will appear. This Utility will allow you to manage all the
advanced features of the Belkin Wireless Card.
8
9
3. Under the “Wireless Network Properties” tab, select a
network name from the “Available Networks” list and click the
“Properties” button.
10
4. Under “Network Authentication”, select “WPA-PSK (no server).
5. Type your WPA key in the “Network key” box.
Important: WPA-PSK is a mixture of numbers and letters from A-Z
and 0-9. For WPA-PSK you can enter eight to 63 characters. This
network key needs to match the key you assign to your Router.
6. Click “OK, then “Apply” to save the settings.
I am NOT using a Belkin client card for a home network and I
am having difficulty setting up Wireless Protected Access (WPA)
security.
Solution:
If you are not using a Belkin Wireless Desktop or Wireless Notebook
Network Card that is not equipped with WPA-enabled software, a
file from Microsoft called “Windows XP Support Patch for Wireless
Protected Access” is available for free download. Download the
patch from Microsoft by searching the knowledge base for Windows
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
XP WPA.
Note: The file that Microsoft has made available works only with
Windows XP. Other operating systems are not supported at this
time. You also need to ensure that the wireless card’s manufacturer
supports WPA and that you have downloaded and installed the
latest driver from their support site.
Supported Operating Systems:
• Windows XP Professional
• Windows XP Home Edition
1. Under Windows XP, click “Start > Control Panel > Network
Connections”.
2. Right-click on the “Wireless Networks”. Ensure the “Use
Windows to configure my wireless network settings” check box
is checked.
3. Under the “Wireless Networks” tab, click the “Configure” button.
4. For a home or small business user, select “WPA-PSK” under
“Network Administration”.
Note: Select WPA (with radius server) if you are using this computer
to connect to a corporate network that supports an authentication
server such as a radius server. Please consult your network
administrator for further information.
5. Select “TKIP” or “AES” under “Date Encryption”. This setting will
have to be identical to the Router that you set up.
6. Type in your encryption key in the “Network key” box.
Important: Enter your pre-shared key. This can be from eight to 63
characters and can be letters, numbers, or symbols. This same key
must be used on all of the clients that you set up.
7. Click “OK” to apply settings.
What’s the difference between 802.11b, 802.11g, 802.11a, and
draft 802.11n?
Currently there are four levels of wireless networking standards, which
transmit data at very different maximum speeds. Each is based on
the designation for certifying network standards. The most common
wireless networking standard, 802.11b, transmits information at
11Mbps; 802.11a and 802.11g work at 54Mbps; and draft 802.11n
works at 108Mbps. See the following chart for more detailed
information.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1
2
Wireless Comparison Chart
3
4
11Mbps
link rate /
Baseline
5x faster
than
802.11b*
10x faster
than
802.11b*
10x faster
than
802.11b*
15x faster
than
802.11b*
Speed*
5
Common
household
devices
Common
household
devices
Common
household
devices
Common
household
devices
Common
household
devices
6
such as
such as
such as
such as
such as
cordless
phones and
microwave
ovens may
interfere
with the
cordless
phones and
microwave
ovens may
interfere
with the
cordless
phones and
microwave
ovens may
interfere
with the
cordless
phones and
microwave
ovens may
interfere
with the
cordless
phones and
microwave
ovens may
interfere
with the
7
8
unlicensed
band
unlicensed
band
unlicensed
band
unlicensed
band
unlicensed
band
2.4GHz
2.4GHz
2.4GHz
2.4GHz
2.4GHz
9
10
Compatible with
draft 802.11n**
and 802.11b/g
Compatible with Compatible with Compatible with Compatible with
802.11g
802.11b/g
802.11b/g
802.11b/g
typically
100–200 ft.
indoors
Up to
400ft*
Up to
700ft*
Up to
1000ft*
Up to
1,400 ft.
Better
coverage
and
consistent
speed at
range
Leading
edge—
best
coverage
and
Common—
widespread
use for
Internet
sharing
Mature—
legacy
technology
Enhanced
speed and
coverage
throughput
**Distance and connection speeds will vary depending on your networking environment.
**This Router is compatible with products based on the same version of the draft 802.11n
specifications and may require a software upgrade for best results.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Technical Support
Belkin Technical Support
For latest software updates or if you have any further questions
regarding installation of this product, please visit
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
1
2
FCC Statement
DECLARATION OF CONFORMITY WITH FCC RULES FOR
ELECTROMAGNETIC COMPATIBILITY
We, Belkin Corporation, of 501 West Walnut
Street, Compton, CA 90220, declare under our sole
responsibility that the product,
3
4
F5D9630-4
5
to which this declaration relates,
complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
6
7
8
Caution: Exposure to Radio Frequency Radiation.
The radiated output power of this device is far below the FCC radio
frequency exposure limits. Nevertheless, the device shall be used in such a
manner that the potential for human contact during normal operation
is minimized.
When connecting an external antenna to the device, the antenna shall be
placed in such a manner to minimize the potential for human contact during
normal operation. In order to avoid the possibility of exceeding the FCC radio
frequency exposure limits, human proximity to the antenna shall not be less
than 20cm (8 inches) during normal operation.
9
10
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try and correct the interference by one
or more of the following measures:
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
•
•
•
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications to this device that
are not expressly approved by Belkin Corporation may void the user’s authority to operate the
equipment.
Canada-Industry Canada (IC)
The wireless radio of this device complies with RSS 139 & RSS 210 Industry Canada. This Class
B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada.
Europe-European Union Notice
Radio products with the CE 0560 or CE alert marking
comply with the R&TTE Directive (1995/5/EC) issued by the
Commission of the European Community.
Compliance with this directive implies conformity to the following European Norms (in brackets
are the equivalent international standards).
•
•
•
EN 60950 (IEC60950) – Product Safety
EN 300 328 Technical requirement for radio equipment
ETS 300 826 General EMC requirements for radio equipment.
To determine the type of transmitter, check the identification label on your Belkin product.
Products with the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage
Directive (72/23/EEC) issued by the Commission of the European Community. Compliance
with these directives implies conformity to the following European Norms (in brackets are the
equivalent international standards).
•
•
•
•
•
EN 55022 (CISPR 22) – Electromagnetic Interference
EN 55024 (IEC61000-4-2,3,4,5,6,8,11) – Electromagnetic Immunity
EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics
EN 61000-3-3 (IEC610000) – Power Line Flicker
EN 60950 (IEC60950) – Product Safety
Products that contain the radio transmitter are labeled with CE 0560 or CE alert marking
and may also carry the CE logo.
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to dispose of your
waste equipment by handing it over to a designated collection point for the recycling of waste
electrical and electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and ensure
that it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling, please
contact your local city office, your household waste disposal service or the shop where
you purchased the product.
Belkin Corporation Limited Lifetime Product Warranty
What this warranty covers.
Belkin Corporation warrants to the original purchaser of this Belkin product that the product
shall be free of defects in design, assembly, material, or workmanship.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
1
2
What the period of coverage is.
Belkin Corporation warrants the Belkin product for the lifetime of the product.
What will we do to correct problems?
Product Warranty.
Belkin will repair or replace, at its option, any defective product free of charge (except for shipping
charges for the product).
What is not covered by this warranty?
3
All above warranties are null and void if the Belkin product is not provided to Belkin Corporation
for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin Corporation
determines that the Belkin product has been improperly installed, altered in any way, or tampered
with. The Belkin Product Warranty does not protect against acts of God (other than lightning)
such as flood, earthquake, war, vandalism, theft, normal-use wear and tear, erosion, depletion,
obsolescence, abuse, damage due to low voltage disturbances (i.e. brownouts or sags), non-
authorized program, or system equipment modification or alteration.
4
5
How to get service.
6
To get service for your Belkin product you must take the following steps:
1. Contact Belkin Corporation at 501 W. Walnut St., Compton CA 90220, Attn: Customer Service,
or call (800)-223-5546, within 15 days of the Occurrence. Be prepared to provide the following
information:
7
a. The part number of the Belkin product.
b. Where you purchased the product.
c. When you purchased the product.
8
d. Copy of original receipt.
2. Your Belkin Customer Service Representative will then instruct you on how to forward your
receipt and Belkin product and how to proceed with your claim.
9
Belkin Corporation reserves the right to review the damaged Belkin product. All costs of shipping
the Belkin product to Belkin Corporation for inspection shall be borne solely by the purchaser.
If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment
to Belkin Corporation, Belkin may designate, in its sole discretion, an equipment repair facility to
inspect and estimate the cost to repair such equipment. The cost, if any, of shipping the equipment
to and from such repair facility and of such estimate shall be borne solely by the purchaser.
Damaged equipment must remain available for inspection until the claim is finalized. Whenever
claims are settled, Belkin Corporation reserves the right to be subrogated under any existing
insurance policies the purchaser may have.
10
How state law relates to the warranty.
THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN CORPORATION, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED,
INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE
LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above
limitations may not apply to you.
IN NO EVENT SHALL BELKIN CORPORATION BE LIABLE FOR INCIDENTAL, SPECIAL,
DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT
LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY
BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
This warranty gives you specific legal rights, and you may also have other rights, which may
vary from state to state. Some states do not allow the exclusion or limitation of incidental,
consequential, or other damages, so the above limitations may not apply to you.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless G+ MIMO
ADSL2+ Modem Router
Free Tech Support*
You can find additional support information on our website www.belkin.com
through the tech-support area. If you want to contact technical support by phone,
please call the number you need from the list below*.
*Local rates apply
Country
Number
Internet adress
AUSTRIA
0820 200766
BELGIUM
07 07 00 073
CZECH REPUBLIC
DENMARK
FINLAND
239 000 406
701 22 403
00800 - 22 35 54 60
08 - 25 54 00 26
0180 - 500 57 09
00800 - 44 14 23 90
06 - 17 77 49 06
800 8534
FRANCE
GERMANY
GREECE
HUNGARY
ICELAND
IRELAND
0818 55 50 06
02 - 69 43 02 51
34 20 80 85 60
0900 - 040 07 90
81 50 0287
ITALY
LUXEMBOURG
NETHERLANDS
NORWAY
€0.10 per minute
POLAND
00800 - 441 17 37
707 200 676
PORTUGAL
RUSSIA
495 580 9541
0800 - 99 15 21
902 - 02 43 66
07 - 71 40 04 53
08 - 48 00 02 19
0845 - 607 77 87
SOUTH AFRICA
SPAIN
SWEDEN
SWITZERLAND
UNITED KINGDOM
OTHER COUNTRIES
+44 - 1933 35 20 00
Belkin Ltd.
Belkin B.V.
Belkin GmbH
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
Boeing Avenue 333
1119 PH Schiphol-Rijk
Netherlands
+31 (0) 20 654 73 00
+31 (0) 20 654 73 49 fax
Hanebergstrasse 2
80637 Munich
Germany
+49 (0) 89 14 34 05 0
+49 (0) 89 14 34 05 100 fax
+44 (0) 1933 31 2000 fax
Belkin SAS
130 rue de Silly
92100 Boulogne-Billancourt
France
Belkin Iberia
Belkin Sweden
Knarrarnäsgatan 7
164 40 Kista
Avda. Cerro del Aguila 3
28700 San Sebastián de los Reyes
Spain
Sweden
+33 (0) 1 41 03 14 40
+33 (0) 1 41 31 01 72 fax
+34 91 625 80 00
+34 902 02 00 34 fax
+46 (0) 8 5229 1870
+46 (0) 8 5229 1874 fax
© 2007 Belkin International, Inc. All rights reserved. All trade names are
registered trademarks of respective manufacturers listed. Mac, Mac OS, Apple, and AirPort are trademarks
of Apple Computer, Inc., registered in the U.S. and other countries. Windows, Microsoft, and NT are either
registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
P75125uk_A
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Belkin DVD Player PF31 User Manual
Black Box Switch LB9306A User Manual
Blanco Indoor Furnishings 157 149 User Manual
Blue Sea Systems Air Conditioner PN 8408 User Manual
Bosch Appliances Home Security System AR18 09 B014 User Manual
Bosch Power Tools Impact Driver 1194AVSR User Manual
Cadco Convection Oven OV 250 User Manual
Califone Headphones 2924AVG User Manual
Carrier Refrigerator Miracool User Manual
C Crane Portable Radio PR D4VW User Manual