Audiovox Remote Starter PRO 9276C User Manual

Model PRO-9276C  
Owner’s Manual  
7 Channel Remote Car Starter  
FEATURES :  
2 Five Button Programmable RF Transmitters  
Seven Channel Receiver (capable of accepting 4 transmitters)  
Code Hopping Technology  
External SuperheterodyneReceiver Antenna w/PushButton Switch &  
LED  
Safe Start RF Control (Double Push Of RF Transmitter)  
Selectable Automatic Timed Start Mode  
( + ) and ( - ) Keyless Entry Outputs  
On-Board Start Relay  
On-Board Accessory Relay  
3 On-Board Ignition Relays  
On-Board Parking Light Relay  
Ignition 2 & 3 Relay Selectable On or Off During Cranking  
Ground Output While Running / Shock By-Pass / GM VAT Output  
(relay required)  
Tach Signal Learning Circuit  
Two ( + ) and Two ( - ) Safety Shutdown Circuits  
Alarm By-Pass Output  
Channel 3 Output for Remote Trunk Release (relay required)  
Channel 4, 5, 6, & 7 Output to Control Optional Accessories  
Selectable Steady or Flashing Parking Lights for Run Indication  
Selectable Run Times  
Selectable Door Lock Output Pulse Timing  
Optional Illuminated Entry Output (Relay Required)  
Vehicle Horn Activation Output For R/S Annunciation  
External Activation Control Input  
Turbo Timer Mode  
OPTIONS:  
Telematic Upgrade Ready  
Plug In Flash Logic By-Pass Capable  
Remote Power Window Control  
Remote Garage Door Interface  
Multiple Vehicle Capable  
WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle  
starting device. A running engine produces dangerous carbon monoxide fumes  
which can be harmful or fatal if prolonged exposure occurs. DO NOT remote  
start the vehicle if the car is garaged.  
128-8785  
1 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To activate the optional accessory, press and hold the trunk/key button on the keychain  
transmitter for four seconds.  
NOTE: The feature that has been added to channel 3 will always be activated using the  
same transmitter button that remotely starts the vehicle. There is no way to  
move the channel 3 function to a different transmitter button.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 4)  
This system has an additional feature that can be connected to a number of different  
optional accessories. Some of the more common uses for this channel are:  
Can Be Set Up To Activate Rear Window Defogger During Remote  
Start If Vehicle Is So Equipped  
Remote Window Closure  
Rear Hatch Release  
Right Or Left Slider Doors in An Equipped Van  
To activate the optional accessory, press the option button on the keychain transmitter.  
The optional accessory will immediately engage.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 5)  
This system has an additional feature that can be connected to a number of different  
optional accessories. Some of the more common uses for this channel are:  
Remote Trunk Release  
Remote Window Closure  
Rear Hatch Release  
Right Or Left Slider Doors in An Equipped Van  
To activate the optional accessory, press the option button on the keychain transmitter.  
The optional accessory will immediately engage.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 6)  
This system has an additional feature that can be connected to a number of different  
optional accessories. Some of the more common uses for this channel are:  
Rear Hatch Release  
Right Or Left Slider Doors in An Equipped Van  
Driver Priority Settings In Vehicles So Equipped  
To activate the optional accessory, press the option button on the keychain transmitter.  
The optional accessory will immediately engage.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 7)  
This system has an additional feature that can be connected to a number of different  
optional accessories. Some of the more common uses for this channel are:  
Rear Hatch Release  
Right Or Left Slider Doors in An Equipped Van  
Driver Priority Settings In Vehicles So Equipped  
Second Driver Priority Settings In Vehicles So Equipped  
To activate the optional accessory, press the option button on the keychain transmitter.  
The optional accessory will immediately engage.  
NOTE:  
If your system utilizes the transmitter shown, the second option button may  
be configured to operate additional accessories. Please consult your  
installing retailer for more information concerning the options available.  
Page 3  
128-8785  
3 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PUSH-BUTTONLEDRECEIVERVALET/OVERRIDE/SAFETYCONTROLSWITCH  
The Push-Button LED switch located in the receiver allows you to temporarily disable the  
remote starting function of the system. This recommended whenever the vehicle is being  
serviced. To place the system in the service mode:  
1) With the system disarmed/unlocked, and the ignition switch off Press and Hold the  
Push-Button, found on the windshield receiver, in.  
2) Turn the ignition switch on, off, on, off, on, off.  
3) The LED begins to flash two short flashes followed by one long flashes and  
continues this pattern until returned to normal mode of operation.  
This puts the unit into the R/S Override mode indicating that the remote start is in the  
service mode and will not start from RF or any other input Posse or otherwise.  
To Exit R/S Override Mode  
1) With the system disarmed, Press and Hold the Push-Button, found on the windsheild  
receiver, in.  
2) Turn the ignition switch on, off, on, off, on, off.  
3) The LED turns off indicating that the R/S unit is fully functional one again.  
TURBO TIMER MODE  
This system provides a means to cool down the vehicles turbo charger, if so equipped, by  
allowing the vehicle to continue to run for a prescribed period of time every time the  
vehicle's engine is turned off. This feature requires the system to be set up for turbo timer  
during installation. Consult with your installation center to be certain this feature was  
activated and how long the vehicle will continue to run, 3, 5, or 10 minutes after the ignition  
switch is turned off.  
To activate the turbo timer:  
Anytime the engine is running for more than 15 seconds:  
1) Place the gear selector in park.  
2) Set the parking, (hand), brake.  
3) Be certain your foot is off the brake pedal.  
4) Press the receiver's program/Push-Button switch 2 times within 5 seconds.  
The parking lights will flash two times indicating the mode was successfully entered.  
If your parking lights flashed four times, this indicates the turbo mode was on and is now  
turned off.  
With the turbo timer mode selected on, after you've arrived at your destination, while the  
engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch  
to the off position. The engine will continue to run the allotted time according to the  
selection during installation.  
If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle's  
brake, or release the parking brake, or activate the transmitter's start button two times in  
succession. Any of these will cause the engine to turn off.  
REMOTE STARTING THE VEHICLE  
The system WILL NOT start the vehicle if any one of the following conditions exists:  
1. The Vehicle Hood Is Opened.  
2. The Gear Selector Is In Any Gear Other Then Park.  
3. The Brake Is Depressed.  
4. The System is in the Remote Start Override mode  
Page 4  
128-8785  
4 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle  
starting device. A running engine produces dangerous carbon monoxide  
fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT  
remote start the vehicle if the car is garaged.  
To Remote Start The Vehicle:  
Press and release the trunk/key button of your keychain transmitter two times within 2  
seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15 or 20  
minutes. As a visual indication, the parking lights will flash or turn on dependent on the  
programming set up by your installation center.  
When you arrive at your vehicle, unlock it with the key or by pressing and releasing the  
trunk/key button of your keychain transmitter. Enter the vehicle and turn the ignition key to  
the on position.  
CAUTION! Do not turn the key to the start position. This will cause the starter motor to  
engage with the already running engine which could result in damage. Step  
on the brake pedal to disengage the remote start unit. The vehicle will continue  
to run but now on it's own power.  
NOTE: The engine will stop running before the expiration of the pre-programmed run timer  
or if you complete any of the following:  
1. Press and release the trunk/key button of your keychain transmitter two times within 2  
seconds.  
2. Depress the brake pedal.  
3. Open the hood.  
4. Place the system in the Remote Start Override mode.  
5. Race the engine to above 4000 RPM.  
OPERATING ON AUTOMATIC START UP TIMER MODE  
The system has the ability to automatically start the vehicle every 2 or 4 hours over a 48  
hour period. This feature is especially useful in cold climates where the only means to  
keep the engine and engine fluids warm is to periodically start the engine.  
WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle  
starting device. A running engine produces dangerous carbon monoxide  
fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT  
remote start the vehicle if the car is garaged.  
TO BEGIN THE AUTOMATIC START UP TIMER  
1. Turn the ignition key on then off.  
2. Within 10 seconds, activate the RF start command two times. (Push the second channel  
button of your keychain transmitter 4 times).  
The parking lights will flash 4 times indicating the timed start mode is activated.  
The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-  
programmed time (5, 10, 15 or 20 minutes), and then shut off. This will continue for 48  
hours.  
NOTE: The automatic start up timer can also be initiated from the keychain transmitter.  
To do this:  
1. Start the vehicle using the keychain transmitter by pressing and releasing the trunk/key  
button transmitter button 2 times.  
2. Shut off the vehicle using the keychain transmitter by pressing and releasing the trunk/  
key transmitter button 2 times.  
Page 5  
128-8785  
5 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Within 10 seconds of step 2, activate the RF start command two times. (Push the trunk/  
key button of your keychain transmitter 4 times).  
The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is  
activated.  
CANCELING THE AUTOMATIC START UP TIMER  
To cancel the automatic start up timer do one of the following;  
1. Start the vehicle manually with the use of the ignition key and depress the brake pedal.  
2. Remote start the vehicle using your keychain RF transmitter.  
3. Shut off the vehicle using the keychain transmitter by pressing and releasing the trunk/  
key transmitter button 2 times.  
TELEMATIC UPGRADE:  
This system has the ability to have a telematic upgrade module connected to it. This is an  
upgrade that can give you control of certain functions of your vehicle from a Telephone, or  
in some cases a computer interface. Please check with your installation center for most  
recent Telematic Upgrades. If you had a Telematic Upgrade installed, the manual supplied  
with the upgrade unit will provide a operators manual advising of the features of the system  
and means available to control these features of your vehicle.  
PROGRAMMED TRANSMITTER NOTIFICATION (PTN)  
Every time after Disarm when the ignition key is turned on, the unit's LED will report the  
number of transmitters programmed into the system. This safety feature will alert you if  
an unauthorized transmitter has been programmed into your vehicle's security system  
without your knowledge. Typical from the factory, there will be a 2 flash, pause,  
repeated 3 times indicating that two transmitters are programmed into the system. If you  
note additional flashes, there may heve been an additional transmitter added without  
your knowledge or authorization. If you notice a change in the transmitter LED report  
pattern, you can correct this by looking up how to erase and reprogram your transmit-  
ters found in the transmitter programming guide. This reprogram operation will erase all  
unauthorized or unwanted transmitters.  
FUNCTION SETTING CHART  
To be completed by installer:  
Door Lock Timer  
Parking Lights  
Run Time  
1 Sec.  
Steady  
5 Min  
On  
3.5 Sec.  
Pulsed  
10 Min  
Off  
1 Sec/Dbl 1 Sec.  
15 Min  
20 Min  
Accy Lock  
Accy Unlock  
Dr. Door  
All Doors  
Off  
NOTE: Two step unlock is an option and may not have been installed.  
Page 6  
128-8785  
6 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE LEFT BLANK INTENTIONALLY  
Page 7  
128-8785  
7 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2010 Audiovox Electronics Corporation, Hauppauge, NY 11788  
128-8785  
128-8785  
8 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com Network Card 100 PCI User Manual
Acer Computer Monitor X263W User Manual
ACTiSYS Battery Charger CAM 6500 User Manual
Amana Furnace GUD X User Manual
Asus Car Video System MS226H User Manual
Audiovox Automobile Alarm PRO9246ft3 User Manual
Ayre Acoustics Stereo Amplifier K 5XEMP User Manual
Baldor Outboard Motor BSC 7107 DC User Manual
BB Electronics Model Vehicle ESR901 User Manual
BC Speakers Portable Speaker DE1000 User Manual