TABLE OF CONTENTS
SPECIAL NOTES ON LCD MONITORS........................................................ 1
INFORMATION FOR YOUR SAFETY AND COMFORT............................... 2
UNPACKING.................................................................................................. 5
ATTACHING / REMOVING THE BASE......................................................... 6
SCREEN POSITION ADJUSTMENT............................................................. 6
WALL MOUNTING (OPTIONAL)................................................................... 7
CONNECTING THE POWER CORD ............................................................. 8
SAFETY PRECAUTION................................................................................. 8
CLEANING YOUR MONITOR........................................................................ 8
POWER SAVING ........................................................................................... 9
DDC................................................................................................................ 9
CONNECTOR PIN ASSIGNMENT................................................................. 10
STANDARD TIMING TABLE......................................................................... 12
INSTALLATION ............................................................................................. 13
USER CONTROLS......................................................................................... 14
HOW TO ADJUST A SETTING ..................................................................... 15
TROUBLESHOOTING ................................................................................... 19
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
INFORMATION FOR YOUR SAFETY AND COMFORT
Safety instructions
Read these instructions carefully. Keep this document for future reference. Follow all warnings and
instructions marked on the product.
CAUTION for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to the power supply unit:
Install the power supply unit before connecting the power cord to the AC power outlet.
Unplug the power cord before removing the power supply unit from the product.
If the system has multiple sources of power, disconnect power from the system by unplugging all power
cords from the power supplies.
CAUTION for accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the
equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug
the power cord from the electrical outlet.
Warnings
y
y
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously
damaged.
y
y
Slots and openings are provided for ventilation to ensure reliable operation of the product and to
protect it from overheating. These openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product
should never be placed near or over a radiator or heat register, or in a built-in installation unless proper
ventilation is provided.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind
onto or into the product.
y
y
To avoid damage of internal components and to prevent battery leakage, do not place the product on
a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment which will probably cause
unexpected short current or damage rotor devices, HDD, Optical drive, and even exposure risk from
lithium battery pack.
Safe listening
Follow these instructions, suggested by hearing experts, to protect your hearing.
y
y
y
y
y
Gradually increase the volume until you can hear it clearly and comfortably and without distortion.
After setting the volume level, do not increase it after your ears adjust.
Limit the amount of time listening to music at high volume.
Avoid turning up the volume to block out noisy surroundings.
Turn the volume down if you can’t hear people speaking near you.
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel when:
y
y
y
y
y
the power cord or plug is damaged, cut or frayed liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need for service
the product does not operate normally after following the operating instructions
Note: Adjust only those controls that are covered by the operating instructions, since improper
adjustment of other controls may result in damage and will often require extensive work by a
qualified technician to restore the product to normal condition.
LCD Pixel Statement
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless, some pixels may
occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not
constitute a malfunction.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use. Users are also at risk of
physical injury after long hours of working in front of a computer. Long work periods, bad posture, poor work
habits, stress, inadequate working conditions, personal health and other factors greatly increase the risk of
physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis or other
musculoskeletal disorders. The following symptoms may appear in the hands, wrists, arms, shoulders, neck
or back:
y
y
y
y
y
numbness, or a burning or tingling sensation
aching, soreness or tenderness
pain, swelling or throbbing
stiffness or tightness
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort and/or pain related to computer
use, consult a physician immediately and inform your company’s health and safety department.
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest, or raising your sitting
height to achieve maximum comfort. Observe the following tips:
y
y
y
refrain from staying too long in one fixed posture
avoid slouching forward and/or leaning backward
stand up and walk around regularly to remove the strain on your leg muscles
y
take short rests to relax your neck and shoulders
y
y
y
avoid tensing your muscles or shrugging your shoulders
install the external display, keyboard and mouse properly and within comfort able reach
if you view your monitor more than your documents, place the display at the center of your desk to
minimize neck strain
EN-
3
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly
focused screens, very small typefaces and low-contrast displays could stress your eyes. The following
sections provide suggestions on how to reduce eyestrain.
Eyes
y Rest your eyes frequently.
y Give your eyes regular breaks by looking away from the monitor and focusing on a distant point.
y Blink frequently to keep your eyes from drying out.
Display
y Keep your display clean.
y Keep your head at a higher level than the top edge of the display so your eyes point downward
when looking at the middle of the display.
y Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability
and graphics clarity.
y Eliminate glare and reflections by:
Š
Š
Š
Š
Š
Š
placing your display in such a way that the side faces the window or any light source
minimizing room light by using drapes, shades or blinds
using a task light
changing the display’s viewing angle
using a glare-reduction filter
using a display visor, such as a piece of cardboard extended from the display’s top front edge
y Avoid adjusting your display to an awkward viewing angle.
y Avoid looking at bright light sources, such as open windows, for extended periods of time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing and productive:
y Take short breaks regularly and often.
y Perform some stretching exercises.
y Breathe fresh air as often as possible.
y Exercise regularly and maintain a healthy body.
Warning! We do not recommend using the product on a couch or bed. If this is unavoidable, work
for only short periods, take breaks regularly, and do some stretching exercises.
For more information and help in recycling, please visit the following websites: Worldwide:
EN-
4
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
UNPACKING
Please check the following items are present when you unpack the box, and save the packing materials in
case you will need to ship or transport the monitor in future.
LCD Monitor
15-pin D-Sub Cable
DVI Cable
AC Power Cord
(Only Dual-Input Model)
User Manual
Quick Start Guide
EN-
5
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
ATTACHING / REMOVING THE BASE
Install:
Align the release button on the bottom of the monitor with the corresponding slots on the bottom of the base.
SCREEN POSITION ADJUSTMENT
In order to optimize the best viewing position, you can adjust the tilt of the monitor by using both of your
hands to hold the edges of the monitor as shown in the figure below.
The monitor can be adjusted to 15 degrees up or 5 degrees down as indicated by arrow below.
EN-
6
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
WALL MOUNTING (OPTIONAL)
To obtain a wall-mounting kit, contact your local dealer, Refer to the instructions that come with the base
mounting kit.
Screw holes (100 mm X 100 mm)
* For use only with UL Listed Wall Mount Bracket
EN-
7
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
CONNECTING THE POWER CORD
y Check first to make sure that the power cord you use is the correct type required for your area.
y This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V
AC voltage areas. No user-adjustment is required.
y Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet.
y For unit using at 120 V AC:
y Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V.
y For unit using at 220/240 V AC (outside of U.S.):
y Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The cord set should have the
appropriate safety approvals for the country in which the equipment will be installed.
SAFETY PRECAUTION
y Avoid placing the monitor, or any other heavy object, on the power cord to avoid damage to the cable.
y Do not expose the monitor to rain, excessive moisture, or dust.
y Do not cover the ventilation slots or openings of the monitor. Always put the monitor in a place where
there is adequate ventilation.
y Avoid placing the monitor against a bright background or where sunlight or other light sources may
reflect on the face of the monitor. Place the monitor just below eye level.
y Handle with care when transporting the monitor.
y Refrain from giving shock or scratch to the screen, as screen is fragile.
CLEANING YOUR MONITOR
Please carefully follow the below guidelines when cleaning the monitor.
y Always unplug the monitor before cleaning.
y Use a soft cloth to wipe the screen and cabinet front and sides.
EN-
8
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
POWER SAVING
The monitor will be driven into Power Saving” mode by the control signal from the display controller, as
indicated by the amber-color power LED.
State
ON
LED Light
Blue
Power Saving Mode
Amber
The power saving states will be kept until a control signal has been detected or the keyboard or mouse is
activated. The recovery time from Active OFF state back to ON state is around 5 seconds.
DDC
To make your installation easier, the monitor is able to Plug and Play with your system if your system also
supports DDC protocol. The DDC (Display Data Channel) is a communication protocol through which the
monitor automatically informs the host system about its capabilities, for example, supported resolutions and
corresponding timing. The monitor supports DDC2B standard.
EN-
9
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
CONNECTOR PIN ASSIGNMENT
15-Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
Red
PIN NO.
9.
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
+5V
Green
10.
Logic Ground
Monitor Ground
DDC-Serial Data
H-Sync
Blue
11.
Monitor Ground
DDC-return
R-Ground
G-Ground
B-Ground
12.
13.
14.
V-Sync
15.
DDC-Serial Clock
EN-
10
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
24-Pin Color Display Signal Cable
PIN
1.
Meaning
PIN
13.
14.
15.
16.
17.
18.
Meaning
TMDS Data3+
+5V Power
TMDS Data2-
TMDS Data2+
TMDS Data 2/4 Shield
TMDS Data4-
2.
3.
GND(return for +5V hsync.vsync)
Hot Plug Detect
4.
5.
TMDS Data4+
DDC Clock
TMDS Data0-
6.
TMDS Data0+
7.
DDC Data
19.
TMDS Data 0/5
8.
9.
Analogue Vertical Sync
TMDS Data1-
20.
21.
22.
23.
24.
TMDS Data5-
TMDS Data5+
10.
11.
12.
TMDS Data1+
TMDS Clock Shield
TMDS Clock+
TMDS Data 1/3 Shield
TMDS Data3-
DDC TMDS Clock-
EN-
11
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
HDMI 19pin Connector
Pin No.
Pin Function
Pin No.
Pin Function
T.M.D.S Clock Ground
T.M.D.S Clock-
NC
1
2
T.M.D.S Data 2+
11
T.M.D.S Data 2 Ground
T.M.D.S Data 2-
12
13
14
15
16
17
18
19
3
4
T.M.D.S Data 1+
NC
5
T.M.D.S Data 1 Ground
T.M.D.S Data 1-
Clock line (SCL)
Data line (SDA)
Ground
6
7
T.M.D.S Data 0+
8
T.M.D.S Data 0 Ground
T.M.D.S Data 0-
+5V
9
Hot Plug Detect
10
T.M.D.S Clock+
EN-
12
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
STANDARD TIMING TABLE
To reduce the need for adjustment for different modes, the monitor has default setting modes that are most
commonly used as given in the table below. For optimum adjustment, the user is suggested to perform the
Auto Setup under Windows “Full Screen” pattern or using the pattern in the floppy disk provided. The only
condition to store as a user mode is the new display information must have 1 KHz difference for horizontal
frequency or 1 Hz for vertical frequency or the sync signal polarities are different from the default modes.
Display Mode
VGA 640x480
Hor. Frequency Vert. Frequency Pixel Frequency SYNC Polarity
(kHz)
(MHz)
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
108.000
108.000
135.000
106.500
146.250
154.000
28.322
30.240
57.283
80.000
13.500
27.000
74.176
74.176
148.500
(H/V)
(Hz)
VESA
31.469
37.861
37.500
35.156
37.879
48.077
46.875
48.363
56.476
60.023
67.500
63.981
79.976
55.935
65.290
74.038
31.469
35.000
49.725
60.150
15.730
31.470
33.720
44.960
67.500
59.940
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.069
75.029
75.000
60.020
75.025
55.887
59.954
59.950
70.087
66.667
74.500
74.720
29.970
59.940
29.970
59.940
60.000
-/-
-/-
-/-
SVGA 800x600
XGA 1024x768
+/+
+/+
+/+
+/+
-/-
-/-
+/+
+/+
+/+
+/+
-/+
-/+
+/-
-/+
-/-
SXGA 1152x864
SXGA 1280x1024
WXGA+ 1440x900
WXGA+ 1680x1050
WUXGA 1920x1200 RB
720x400
VGA TEXT
Macintosh
640x480
832x624
-/-
1024x768
-/-
Video
NTSC
-/-
NTSC 480P
1080i
-/-
+/+
+/+
+/+
720P
1080P
EN-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
INSTALLATION
To install the monitor to your host system, please follow the steps as given
below:
Steps
1. 1-1 Connect Video Cable
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the VGA video cable to the computer.
1-2 Digital Cable (Only Dual-Input Model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to
the computer's port.
2. Connect power cord
Connect the power cord to the monitor, then to a properly grounded AC outlet.
3. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer.
This sequence is very important.
4. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose
the problem.
EN-
14
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
USER CONTROLS
Front Panel Controls
1.Power Switch:
To turn ON or OFF the power.
2.Power LED:
Lights up to indicate the power is turned ON.
3.Empowering / Exit:
1) When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu).
2) When OSD menu is in off status, press this button to select scenario mode.
4.Auto Adjust button / Exit:
1)When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu).
2)When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function.
The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus.
5. < / >
Press < or > to select the desired function. Press < or > to change the settings of the current function.
6.MENU / ENTER:
Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON.
EN-
15
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press < or > to select the desired function.
3. Press the MENU-button to select the function that you want to adjust.
4. Press < or > to change the settings of the current function.
5. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-4.
y
P/X Series OSD behave
When user press “MENU” button on front bezel
A. Acer eColor Management
If selected to “Acer eColor Management” item, will appear the Acer eColor” OSD
B. USER
If selected to “USER” item, will appear the Standard OSD
I. Only Analog Input Model
II. Only Dual Input ModeI
EN-
16
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
ADJUSTING THE PICTURE
The descriptions for function control LEDS
A. Acer eColor Management
Main Menu
icon
Sub Menu
icon
Sub Menu item
Description
N/A
N/A
N/A
User mode User defined. Settings can be fine-tuned to suit any situation
Optimal balance of brightness and contrast prevent
Text mode
eyestrain. The most comfortable way to read onscreen text
Standard mode Default Setting. Reflects native display capability
Graphic mode Enhances colors and emphasize fine detail
N/A
N/A
Displays scenes in clearest detail. Pictures and
Movie mode
photographs appear in vibrant colors with sharp detail
B. USER
Main Menu
icon
Sub Menu
icon
Sub Menu item
Description
Adjust the contrast between the foreground and background
of the screen image
Contrast
Brightness
ACM
Adjust the background brightness of the screen image
ACM (Adaptive Contrast Management)A CM ON/OFF
Switch, default "OFF"
Adjust picture Focus
(available in analog mode only)
Focus
Adjust picture Clock
(available in analog mode only)
Clock
EN-
17
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
Main Menu
icon
Sub Menu icon
Sub Menu item
H. Position
Description
Adjust the horizontal position.
(available in Analog mode only)
Adjust the vertical position.
(available in Analog mode only)
V. Position
N/A
N/A
Warm
Cool
Set the color temperature to warm white.
Set the color temperature to cool white.
User /Red
User /Green
User /Blue
Adjusts Red/Green/Blue intensity
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
English
繁體中文
Deutsch
Français
Español
Italiano
Multi-language selection.
EMEA version OSD only
简体中文
日本語
Suomi
Nederlands
Русский
H. Position
V. Position
Adjust the horizontal position of the OSD.
Adjust the vertical position of the OSD.
OSD Timeout
Analog
Adjust the OSD timeout.
N/A
N/A
N/A
Select input signal from analog (D-Sub)
Select input signal from digital(DVI)
(only Dual-Input Model)
Digital (only Dual
Input Model)
DDC/CI
Turn ON/OFF DDC/CI support
Show the resolution, H/V frequency and input port of
current input timing.
N/A
N/A
N/A
Information
Clear each old status of Auto-
configuration and set the color temperature to Cool.
Reset
Exit
Save user adjustment and OSD disappear.
EN-
18
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
Acer eColor Management OSD
User
mode
Text
mode
Standard
mode
Movie
mode
Graphic
mode
Operation instructions
Acer eColor Management
Step 1:
Press “
Key” to open the Acer eColor Management OSD and access the scenario modes
Step 2: Press “<” or “>” to select the mode
Step 3: Press “Auto Key” to confirm the mode and run Auto Adjust
Features and Benefits
Mode
Standard
Text
Features
Benefits
Default settings
Reflects native display capability
Optimal balance of brightness and
contrast prevents eyestrain
The most comfortable way to read onscreen
text
Enhances colors and emphasizes fine
detail
Pictures and photographs appear in vibrant
colors with sharp detail
Graphics
Movie
Presents great visuals, even in unsuitably-lit
environments
Displays scenes in clearest detail
User defined
User
Settings can be fine-tuned to suit any situation
EN-
19
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
TROUBLESHOOTING
Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can
self-diagnose the problem.
(VGA Mode)
Problems
Current Status
LED ON
Remedy
y Using OSD, adjust brightness and contrast to maximum or
reset to their default settings.
y Check the power switch.
LED OFF
y Check if AC power cord is properly connected to the
No Picture
monitor.
y Check if video signal cable is properly connected at the
LED displays amber
color
back of monitor.
y Check if the power of computer system is ON.
y Check if the specification of graphics adapter and monitor is
in compliance which may be causing the input signal
frequency mismatch.
Unstable Picture
y Using OSD, adjust RESOLUTION, CLOCK,
CLOCK-PHASE, H-POSITION and VPOSITION with
non-standard signals.
Abnormal Picture
Display is missing,
center shift, or too small
or too large in display
size
y Using OSD, in case of missing full-screen image, please
select other resolution or other vertical refresh timing.
y Wait for a few seconds after adjusting the size of the image
before changing or disconnecting the signal cable or
powering OFF the monitor.
(DVI Mode)
Problems
Current Status
Remedy
y Using OSD, adjust brightness and contrast to maximum or
LED ON
reset to their default settings.
y Check the power switch.
LED OFF
y Check if AC power cord is properly connected to the
No Picture
monitor.
y Check if video signal cable is properly connected at the
LED displays amber
color
back of monitor.
y Check if the power of computer system is ON.
EN-
20
Download from Www.Somanuals.com. All Manuals Search And Download.
X263W
ENERGY STAR is a government program (public/private partnership) that gives people the power to
protect the environment in a cost effective way and without sacrificing quality or product features.
Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy
efficiency guidelines set by the US Environmental Protection Agency (EPA) and the US Department
of Energy (DOE). In the average home, 75% of all electricity used to power home electronics is
consumed while the products are turned off. ENERGY STAR qualified home electronic products in
the off position use up to 50% less energy than conventional equipment. More information refers to
As an ENERGY STAR partner, Acer Inc. has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
Note: The statement above is applicable only to Acer LCD Monitor with an ENERGY STAR
logo.
This product has been shipped enabled for power management:
z
z
z
Activate display’ Sleep mode within 15 minutes of user inactivity.
Activate computer’s Sleep mode within 30 minutes of user inactivity.
Wake the computer from Sleep mode by pushing power button.
EN-
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Acer Computer (Shanghai) Limited
3F, No. 168 Xizang medium road, Huangpu District,
Shanghai, China
Declaration of Conformity
We,
Acer Computer (Shanghai) Limited
3F, No. 168 Xizang medium road, Huangpu District,
Shanghai, China
Contact Person: Mr. Easy Lai
Tel: 886-2-8691-3089 Fax: 886-2-8691-3000
E-mail: [email protected]
Hereby declare that:
Product:
25.5”W LCD Monitor
Acer
Trade Name:
Model Number: X263W
SKU Number:
X263Wxxx (“x” = 0~9, a ~ z, A ~ Z or Blank)
Is compliant with the essential requirements and other relevant provisions of the following EC
directives, and that all the necessary steps have been taken and are in force to assure that
production units of the same product will continue comply with the requirements.
EMC Directive 89/336/EEC, amended by 92/31/EEC and 93/68/EEC as
attested by conformity with the following harmonized standards:
-. EN55022:1998 + A1:2000 + A2:2003, AS/NZS CISPR22:2002, Class B
-. EN55024:1998 + A1:2001 + A2:2003
-. EN61000-3-2:2000, Class D
-. EN61000-3-3:1995 + A1:2001
Low Voltage Directive 2006/95/EC as attested by conformity with the
following harmonized standard:
-. EN60950-1:2001
RoHS Directive 2002/95/EC on the Restriction of the Use of certain
Hazardous Substances in Electrical and Electronic Equipment
_______________________________
Easy Lai / Director
Acer Computer (Shanghai) Limited
Nov. 13, 2007
Date
Download from Www.Somanuals.com. All Manuals Search And Download.
Acer America Corporation
333 West San Carlos St., San Jose
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
25.5”W LCD Monitor
X263W
Model Number:
SKU Number:
X263Wxxx
(“x” = 0~9, a ~ z, or A ~ Z)
Name of Responsible Party:
Address of Responsible Party:
Acer America Corporation
333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
Download from Www.Somanuals.com. All Manuals Search And Download.
|