AMERICAST® BRAND
SELF RIMMING
™
Installation
Instructions
LAKELAND™ KITCHEN SINKS
SERIES 7193
Thank you for selecting American-Standard...the benchmark of fine quality
for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Certified to comply with ANSI A112.19.4.M
U.S. Patent No. 4,664,982
Other patents pending.
CAN/C.S.A. B-45
Observe local plumbing and building codes.
Refer to American Standard roughing-in information for
specific dimensions for each model.
CUTOUT DIMENSIONS FOR SINKS:
Below are the dimensions needed to determine the cutout size for your
installation. Select the correct diagram for your application and refer to the
instructions below.
BEFORE YOU BEGIN...
Unpack new sink and inspect carefully for damage.
Replace the sink in its original packing carton to
protect it until you are ready to begin installation.
Recommended Tools & Materials
Locate and mark center lines of sink on countertop.
Silicone Sealant
Putty Knife
Pipe Wrench
Channel Locks
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Drill
Provide proper clearance under the countertop for the faucet supply lines and
the structural parts of the cabinet.
Basin Wrench
Saber Saw
Tubing Cutter
Tape Measure
Hacksaw
By using the diagrams below and measuring your sink, draw the outline of
the sink onto the countertop. This is not the cutting outline.
Refer to the diagram for your sink and draw a line the required distance in
from the sink outline. Cut on this line.
Mineral Spirits
COUNTERTOP CUTOUT FOR
COUNTERTOP CUTOUT FOR
UNDERCOUNTER INSTALLATIONS
NEW INSTALLATIONS
33"
(838mm)
27-3/8"
(695mm)
CUTOUT
1" R (25mm) TYP.
1-5/8" (16mm)
SINK
22"
(559mm)
2-5/16" R (19mm) TYP.
16-7/8"
(429mm)
SUPPORT
CLIPS
OUTLINE
5/8"
(16mm)
CUTTING LINE
COUNTERTOP MOUNTED FAUCET
MODEL 7193 UNDER COUNTER MOUNT
LAKELAND SINGLE BOWL
LAKELAND SINGLE BOWL
MODEL 7193 SELF RIMMING
COUNTERTOP CUTOUT FOR
REPLACEMENT INSTALLATIONS
29-1/2"
(749mm)
33"
(838mm)
CUTOUT
1" R (25mm) TYP.
3/4" R (19mm) TYP.
22"
(559mm)
20-1/2"
(521mm)
5/8" to 1-5/8"
(16 to 41mm)
SUPPORT
CLIPS
SINK
OUTLINE
5/8"
(16mm)
CUTTING LINE
SINK MOUNTED FAUCET
MODEL 7193 UNDER COUNTER MOUNT
LAKELAND SINGLE BOWL
LAKELAND SINGLE BOWL
MODEL 7193 SELF RIMMING
CAUTION:
1. Recommended Minimum Countertop Thickness Wood 19mm (3/4") Marble and Solid Surface 12mm (1/2")
2. Prior to cutting countertop ensure that the faucet shank has sufficient length to attach the mounting nut after
the shank goes through both the countertop and the sink deck. The deck is 10mm (3/8") thick.
NOTE: Undercounter Installations of sinks should be done by trained and experienced installers due to the materials (such
as marble, hard synthetics, etc.). Contact your countertop distributor for best method of cutting the opening.
IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN
THE RANGE OF TOLERANCES ESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS.
©AMERICAN STANDARD INC. 2005
791393-100 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS FOR UNDERCOUNTER MOUNTED SINK
WITH COUNTERTOP MOUNTED FAUCET.
1
2
5
Apply a bead of sealant to
the edge of the sink. Hold
the sink against the
Countertop
Countertop
Cutout
Edge
Perimeter
of sink
Sealant
under-side of the
countertop and rotate the
clips to hold the sink in
place. Snug the screws to
hold the sink. Attach all the
additional clips.
Cutout
12mm
(1/2")
Drill a clearance hole inside the cutout line
as marked on the countertop.
Support Clip
6
7
Countertop
Countertop
Perimeter
of sink
Sink
Surface
Cutout
Cut opening on cut line inside the perimeter of sink.
Mount the faucet and drain assembly
on the sink or countertop following
the manufacturer's instructions.
Note - Formica countertop installation only is illustrated.
Contact your countertop distributor for the best method of
cutting other materials such as marble, hard synthetics, etc.
3
Countertop
Template
Countertop
Sink
Surface
Cutout
Cut faucet holes in the countertop and remove the template.
CAUTION
PROPER FIT
Faucet
Prior to beveling the
Connect supply lines to faucet finger tight, and
carefully bend to engage with the supply stops.Tighten
connections to faucet for secure seal.
Escutcheon
countertop edge, be sure that
the faucet escutcheon does
not extend onto the curved
portion of the countertop.
Countertop
4
8
CUTOUT
Trap
B
SUPPORT
CLIPS
A
Single Bowl
Attach at least eight of the support clips to the underside
of the countertop as shown below. The location of the
clips should be as shown in the sink diagram. The wood
screws are for use in wood, plywood, or particle board
(drill appropriate pilot hole). The inserts supplied are for
use in marble or hard synthetic material.
Connect drain assembly hand tight to check alignment. It
may be necessary to cut off part of the tailpiece (area "A")
or part of the horizontal leg of the trap (area "B").
Secure joint for watertight assembly.
3
791393-100 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS FOR UNDERCOUNTER MOUNTED SINK
WITH SINK TOP MOUNTED FAUCET.
Countertop
1
2
7
Drill a clearance
hole inside the
cutout line as
marked on the
countertop.
Perimeter
of sink
Trap
B
A
Single Bowl
Cutout
Cut opening on cut line inside the perimeter of the template.
Note - Formica
Countertop
Connect drain assembly hand tight to check alignment. It
may be necessary to cut off part of the tailpiece (area "A") or
part of the horizontal leg of the trap (area "B").
countertop installation
only is illustrated. Contact
your countertop
Perimeter
of sink
distributor for the best
method of cutting other
materials such as marble,
hard synthetics, etc.
Secure joint for watertight assembly.
CARE AND CLEANING...
Cutout
For all porcelain enamel surfaces, regular, gentle care is best. The
recommended way to preserve the finish, avoid scratches, and clean
porcelain enamel fixtures is to rinse them with detergent and water.
Generally, any of the light duty liquid dishwashing detergents, such as
Palmolive or Dawn, work well. In areas where the water is hard, a heavy duty
CUTOUT
3
4
liquid laundry detergent such as liquid Tide will work better.
Product names listed herein are trademarks of American Standard Inc.unless otherwise noted.
®
Palmolive is a registered trademark of Colgate-Palmolive Co.
SUPPORT
CLIPS
®
®
Tide and Dawn are registered trademarks of Procter and Gamble.
®
AMERICAST LIMITED LIFETIME WARRANTY
If an American-Standard Americast® brand product is found to be defective in
materials or workmanship, after inspection by an authorized American-Standard
representative, American-Standard will repair or, at its option, exchange the product
for a similar model. This warranty extends for the lifetime of the product, so long as it
remains in use in its original place of installation, except that the warranty applies to
a bathing vessel’s slip-resisting surface only for the first year after the product’s initial
installation.
This warranty applies only to the original purchaser and installation of these
products.
This warranty does not apply to whirlpool components or to faucets, drains,
mounting rims, grab bars or other accessories. If manufactured or supplied by
American-Standard, such whirlpool components and accessories are covered under
separate limited warranties.
This warranty does not apply to local building code compliance. Since local
building codes vary considerably, the purchaser of this product should check with a
local building or plumbing contractor to assure local code compliance before
installation.
This warranty shall be void if the Americast® brand product has been moved
from its initial place of installation; if it has been subjected to faulty maintenance,
abuse, misuse, accident or other damage; if it was not installed in accordance with
American-Standard’s instructions; or if it was modified in a manner inconsistent with
the product as shipped by American-Standard.
American-Standard's option to repair or exchange the product under this
warranty does not cover any labor or other costs of removal or installation, nor shall
American-Standard be responsible for any other incidental or consequential
damages attributable to a product defect or to the repair or exchange of a
defective product, all of which are expressly excluded from this warranty.
(Some states or provinces do not allow the exclusion or limitation of implied
warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that
vary from state to state or from province to province, in which case this warranty
does not affect such statutory rights.
Attach at least eight of the support clips to the underside
of the countertop as shown below. The location of the
clips should be as shown in the sink diagram. The wood
screws are for use in wood, plywood, or particle board
(drill appropriate pilot hole). The inserts supplied are for
use in marble or hard synthetic material.
Countertop
Cutout
Apply a bead of sealant to
the edge of the sink. Hold
the sink against the
under-side of the
countertop and rotate the
clips to hold the sink in
place. Snug the screws to
hold the sink. Attach all
the additional clips.
Edge
Sealant
12mm
(1/2")
Support Clip
Countertop
5
6
Mount the faucet and drain
assembly on the sink or
countertop following the
manufacturer's instructions.
Sink
Surface
For service under these warranties, it is suggested that a claim be made through
the contractor or dealer from or through whom the product was purchased, or that a
service request (including a description of the product model and of the defect) be
sent to the following address:
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
Connect supply lines to
faucet finger tight, and
carefully bend to
engage with the supply
stops.Tighten
connections to faucet for
Countertop
In Mexico:
In Canada:
American Standard
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
secure seal.
Sink Surface
Under counter
4
791393-100 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|