Cook, Hold, Smoke Oven
Simple Control
Models:
767-SK
1767-SK
1000-SK-I
1000-SK/II
1767-SK
767-SK
• InstallatIon
• operatIon
1000-SK-I
shown with optional
1000-SK/II
• MaIntenance
burgundy exterior
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE: 262.251.3800 • 800.558.8744 USA/CANADA FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
MN-29760 • 12/11
p r i n t e d i n u .s .a .
Download from Www.Somanuals.com. All Manuals Search And Download.
DELIVErY
UNPAcKINg
1. Carefully remove the
appliance from the
carton or crate.
This Alto-Shaam appliance has been
thoroughly tested and inspected to ensure only
the highest quality unit is provided. Upon
receipt, check for any possible shipping damage
and report it at once to the delivering carrier.
See Transportation Damage and Claims section
located in this manual.
®
®
NOTE: Do not discard the
carton and other
packaging material
until you have
This appliance, complete with unattached
items and accessories, may have been delivered
in one or more packages. Check to ensure that all
standard items and options have been received
with each model as ordered.
inspected the unit
for hidden damage
and tested it for
proper operation.
2. Read all instructions in this manual carefully
Save all the information and instructions
packed with the appliance. Complete and return
the warranty card to the factory as soon as
possible to ensure prompt service in the event of a
warranty parts and labor claim.
before initiating the installation of this appliance.
DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of the
appliance and is to be provided to the owner
or manager of the business or to the person
responsible for training operators. Additional
manuals are available from the Alto-Shaam
Tech Team Service Department.
This manual must be read and understood
by all people using or installing the equipment
model. Contact the Alto-Shaam Tech Team Service
Department if you have any questions concerning
installation, operation, or maintenance.
3. Remove all protective plastic film, packaging
materials, and accessories from the appliance
before connecting electrical power. Store any
accessories in a convenient place for future use.
NOTE: All claims for warranty must include the
full model number and serial number of
the unit.
simple control smokers • installation/operation/service manual - pg. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAfETY PrOcEDUrES
AND PrEcAUTIONS
Knowledge of proper procedures is essential to the
safe operation of electrically and/or gas energized
equipment. In accordance with generally accepted
product safety labeling guidelines for potential
hazards, the following signal words and symbols
may be used throughout this manual.
1. This appliance is intended to cook, hold
or process foods for the purpose of human
consumption. No other use for this appliance is
authorized or recommended.
2. This appliance is intended for use in commercial
establishments where all operators are
familiar with the purpose, limitations, and
associated hazards of this appliance. Operating
instructions and warnings must be read and
understood by all operators and users.
DANgEr
Used to indicate the presence of
a hazard that WILL cause severe
personal injury, death, or substantial
property damage if the warning
included with this symbol is ignored.
3. Any troubleshooting guides, component views,
and parts lists included in this manual are for
general reference only and are intended for use
by qualified technical personnel.
wArNINg
4. This manual should be considered a permanent
part of this appliance. This manual and all
supplied instructions, diagrams, schematics,
parts lists, notices, and labels must remain with
the appliance if the item is sold or moved to
another location.
Used to indicate the presence of
a hazard that CAN cause personal
injury, possible death, or major
property damage if the warning
included with this symbol is ignored.
cAUTION
Used to indicate the presence of a
hazard that can or will cause minor or
moderate personal injury or property
damage if the warning included with
this symbol is ignored.
NOTE
For equipment delivered for use
in any location regulated by the
following directive:
DO NOT DISPOSE OF ELECTRICAL
OR ELECTRONIC EQUIPMENT WITH
OTHER MUNICIPAL WASTE.
cAUTION
Used to indicate the presence of a hazard that
can or will cause minor personal injury, property
damage, or a potential unsafe practice if the
warning included with this symbol is ignored.
NOTE: Used to notify personnel of
installation, operation, or
maintenance information that is
important but not hazard related.
simple control smokers • installation/operation/service manual - pg. 2
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
cAUTION
DANgEr
ALTERATION, ADJUSTMENT,
SERVICE, OR MAINTENANCE COULD
RESULT IN SEVERE INJURY, DEATH,
OR CAUSE PROPERTY DAMAGE.
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN
IN OPERATION. TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
IMPROPER INSTALLATION,
READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.
DANgEr
DO NOT store or use gasoline or other
flammable vapors or liquids in the
vicinity of this or any other appliance.
cAUTION
TO PREVENT PERSONAL INJURY,
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
SITE INSTALLATION
The Alto-Shaam
1. The oven must be installed on a stable and
®
cook and hold oven
must be installed
in a location that
will permit the
oven to function
for its intended
purpose and to allow
adequate clearance
for ventilation,
proper cleaning, and
maintenance access.
level surface.
2. DO NOT install this appliance in any area
where it may be affected by any adverse
conditions such as steam, grease, dripping
water, high temperatures, or any other
severely adverse conditions.
3. DO NOT store or use any flammable liquids or
allow flammable vapors in the vicinity of this
oven or any other appliance.
4. This appliance must be kept free and clear of
any combustible materials.
5. This appliance must be kept free and clear
of any obstructions blocking access for
maintenance or service.
cLEArANcE rEQUIrEMENTS
back
3" (76mm)
top
2" (51mm)
1" (25mm)
each side
simple control smokers • installation/operation/service manual - pg. 3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SITE INSTALLATION
767-SK
1767-SK
28-5/8" (726mm)
11-5/8"
(295mm)
28-5/8" (726mm)
11-5/8"
(295mm)
Electrical
Connection
Electrical
Shown with
Connection
optional bumper
Shown with
optional bumper
32-3/4" (832mm)
31-3/4" (807mm)
25-11/16" (651mm)
Cord Length
120V - 5 ft. (1524mm)
230V - 8 ft. (2438mm)
25-11/16" (651mm)
31-5/8" (802mm)
24-1/8" (612mm)
23-5/8" (600mm)
26-5/8" (676mm)
*31-11/16" (804mm) - with optional 2-1/2" casters
*35-1/16" (890mm) - with optional 5" casters
*33-13/16" (858mm) - with optional 6" legs
24-1/8" (613mm)
23-5/8" (600mm)
26-5/8" (676mm)
*60-11/16" (1540mm) - with optional 3-1/2" (89mm) casters
*62-1/8" (1577mm) - with optional 6" (152mm) legs
wEIghT
cAPAcITY PEr cOMPArTMENT
MODEL
767-SK
NET WEIGHT
197lb (89 kg)
SHIP WEIGHT
225 lb (102 kg)
450 lb (204 kg)
100 lb (45 kg) maximum
1767-SK
355 lb (161 kg) est.
volume maximum: 53 quarts (67 liters)
simple control smokers • installation/operation/service manual - pg. 4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SITE INSTALLATION
1000-SK-I
1000-SK/II
25-1/16" (636mm)
25-1/16" (636mm)
Electrical
Connection
Electrical
Connection
Shown with
optional bumper
Shown with
optional bumper
22-1/2" (572mm)
32-1/4" (819mm)
Cord Length
230V - 8 ft.
(2438mm)
22-1/2"
(572mm)
31-5/8" (802mm)
20-1/2"
(521mm)
23-1/2" (597mm)
26-7/8" (683mm)
20-1/2"
(521mm)
*38-1/2" (977mm) - with optional 2-1/2" casters
*41-15/16" (1064mm) - with optional 5" casters
*41-7/8" (1063mm) - with optional 6" legs
24-1/8" (613mm)
23-1/2" (597mm)
*74-1/4" (1885mm) - with optional 3-1/2" (89mm) casters
*75-1/2" (1917mm) - with optional 6" (152mm) legs
wEIghT
cAPAcITY PEr cOMPArTMENT
MODEL
NET WEIGHT
377 lb (171 kg)
203 lb (92 kg) est.
SHIP WEIGHT
1000-SK-I
1000-SK/II
445 lb (202 kg) est.
282 lb (101 kg) est.
120 lb (54 kg) maximum
volume maximum: 60 quarts (76 liters)
simple control smokers • installation/operation/service manual - pg. 5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SITE INSTALLATION
OPTIONS AND AccESSOrIES
MODEL >
767-SK
1767-SK
1000-SK-I
1000-SK/II
Bumper, Full Perimeter
Carving Holder
5010371
5010371
5009767
5009767
prime rib
HL-2635
HL-2635
HL-2635
HL-2635
steamship (cafeteria) round
4459
4459
4459
4459
Casters - 2 rigid, 2 swivel w/brake
5" (127mm)
3-1/2" (89mm)
2-1/2" (64mm)
5004862
standard
5008022
standard
5008017
––
standard
5008017
––
5004862
standard
5008022
Door Lock with Key
LK-22567
LK-22567
LK-22567
LK-22567
Drip Pan with Drain, 1-11/16" (43mm deep)
Drip Pan without Drain 1-7/8" (62mm deep)
Drip Pan without Drain 4" (101mm deep)
14831
––
––
14831
––
––
5005616
11906
15929
5005616
11906
15929
Legs, 6" (152mm), Stemmed (set of four)
Pan Grid, Wire - 18" x 26" paN iNsert
Security Panel with key lock
5011149
PN-2115
5004750
5011149
PN-2115
5004750
5011149
PN-2115
5011592
5011149
PN-2115
5005776
Shelf, Stainless Steel
flat wire, reach-in
rib rack
SH-2324
SH-2743
SH-2324
SH-2743
SH-2325
SH-29474
SH-2325
SH-29474
Stacking Hardware
5004864
––
––
5004864
Wood Chips, bulk pack
Apple 20 lb (9 kg)
Cherry 20 lb (9 kg)
Hickory 20 lb (9 kg)
Maple 20 lb (9 kg)
WC-22543
WC-22541
WC-2829
WC-22545
WC-22543
WC-22541
WC-2829
WC-22545
WC-22543
WC-22541
WC-2829
WC-22545
WC-22543
WC-22541
WC-2829
WC-22545
fAcTOrY INSTALLED OPTIONS
MODEL >
767-SK
1767-SK
1000-SK-I
1000-SK/II
Door
solid
standard
available
standard
available
standard
available
standard
available
window
Door Swing
right hand
left-hand
standard
available
standard
available
standard
available
standard
available
Exterior Color Options
stainless steel
burgundy
standard
available
available
standard
available
available
standard
available
available
standard
available
available
custom color
simple control smokers • installation/operation/service manual - pg. 6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SITE INSTALLATION
STAcKINg INSTrUcTIONS
1) If the two appliances were shipped together from the factory, the top unit will have the casters
already removed. A stacking kit will be included with the shipment.
If casters need to be removed: lay the unit on its back, and remove the set screw on each caster. Pull the casters
out of the unit.
2) while appliance is laid on its back, insert one stacking post in each of the four corners of the
upper unit. Secure the stacking posts using one screw and two flat washers that come with the
stacking kit.
Note: The flange on the stacking posts must face the outside of the unit.
3) remove the four top mounting screws from the lower unit. Place the upper appliance, which has
the stacking posts installed, on top of the bottom unit. center the top unit from front to back.
re-install the four screws through the flange of the four stacking posts.
STACKING
POSTS
CASTER SET SCREW
TOP
MOUNTING
SCREWS
TOP
MOUNTING
SCREWS
Stacking configurations - 767-SK
Stacking configurations - 1000-SK/II
767-SK with 767-SK, 750-TH/III,
750-TH-II, 767-SK/III, or 750-S
1000-SK/II with 1000-SK/II,
1000-TH/III, or 1000-S
simple control smokers • installation/operation/service manual - pg. 7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SITE INSTALLATION
A number of adjustments are associated with
initial installation and start-up. It is important
that these adjustments be conducted by a qualified
service technician. Installation and start-up
adjustments are the responsibility of the dealer
or user. These adjustments include but are not
limited to thermostat calibration, door adjustment,
leveling, electrical hook-up and installation of
optional casters or legs.
rESTrAINT rEQUIrEMENTS
—MOBILE EQUIPMENT
wArNINg
rISK Of ELEcTrIc ShOcK.
Appliance must be secured
to building structure.
Any appliance that is not furnished with a power
supply cord but that includes a set of casters
must be installed with a tether. Adequate means
must be provided to limit the movement of this
appliance without depending on or transmitting
stress to the electrical conduit. The following
requirements apply:
LEVELINg
Level the oven
from side-to-side and front-to-back
with the use of a spirit level. For ovens installed
with casters, it is important that the installation
surface be level due to the probability of frequent
oven repositioning.
1. Casters must be a maximum height of 6" (152mm).
2. Two of the casters must be the locking type.
We recommend checking the level of the oven
periodically to make certain the floor has not
shifted nor the oven moved.
3. Such mobile appliances or appliances on mobile
stands must be installed with the use of a flexible
connector secured to the building structure.
NOTE: Failure to properly level this oven can
cause improper function and will result
in the uneven baking with products
consisting of semi-liquid batter.
A mounting connector for a restraining device is
located on the upper back flange of the appliance.
A flexible connector is not supplied by nor is it
available from the factory.
simple control smokers • installation/operation/service manual - pg. 8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SITE INSTALLATION
DrIP TrAY INSTALLATION INSTrUcTIONS
b
c
a
d
Item Description
Qty
1
1
2
3
4
Double-Sided Tape
Drip Tray Holder
8-32 x 1/4" Phil Screw
Drip Tray
1
3
1
1. Poke holes through double-sided tape a which is attached to the back of drip tray holder b.
2. Remove backing on double-sided tape a.
3. Put screws c through holes and attach drip tray holder b to unit.
4. Optional, but strongly recommended - apply a line of food-grade silicone caulk along top edge
of drip tray holder b to seal.
5. Place drip tray d in drip tray holder b.
wArNINg
fAILUrE TO PrOPErLY INSTALL
ThE DrIP TrAY cAN Or wILL
cAUSE MAJOr EQUIPMENT
DAMAgE AND wILL rESULT IN
A LEAKAgE hAZArD ThAT cAN
cAUSE PErSONAL INJUrY.
simple control smokers • installation/operation/service manual - pg. 9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
ELEcTrIcAL cONNEcTION
The appliance must be installed by a qualified
service technician. The oven must be properly
grounded in accordance with the National
Electrical Code and applicable local codes.
REGARDING INTERNATIONAL STANDARD UNITS:
If the unit is not equipped with flexible cord and
plug, an all-pole country approved disconnection
device which has a contact separation of at least
3mm in all poles must be incorporated in the fixed
wiring for disconnection. When using a cord
without a plug, the green/yellow conductor shall
be connected to the terminal which is marked with
the ground symbol. If a plug is used, the socket
outlet must be easily accessible. If the power cord
needs replacement, use a similar one obtained
from the distributor.
Plug the unit into a properly grounded receptacle
ONLY, positioning the unit so that the plug is
easily accessible in case of an emergency. Arcing
will occur when connecting or disconnecting the
unit unless all controls are in the “OFF” position.
Proper receptacle or outlet configuration or
permanent wiring for this unit must be installed
by a licensed electrician in accordance with
applicable local electrical codes.
For CE approved units: To prevent an electrical
shock hazard between the appliance and other
appliances or metal parts in close vicinity, an
equalization-bonding stud is provided. An
equalization bonding lead must be connected to
this stud and the other appliances / metal parts
to provide sufficient protection against potential
difference. The terminal is marked
DANgEr
To avoid electrical shock, this
appliance MUST be adequately
with the following symbol.
grounded in accordance with local
electrical codes or, in the absence of
local codes, with the current edition
of the National Electrical Code ANSI/
NFPA No. 70. In Canada, all electrical
connections are to be made in
hard wired models:
Hard wired models must be equipped with a
country certified external allpole disconnection
switch with sufficient contact separation.
accordance with CSA C22.1, Canadian
Electrical Code Part 1 or local codes.
If a power cord is used for the connection of the
product an oil resistant cord like H05RN or H07RN
or equivalent must be used.
NOTE: CE approved appliances must be
connected to an electrical circuit that is
protected by an external GFCI outlet.
DANgEr
ENSURE POWER SOURCE
MATCHES VOLTAGE STAMPED
ON APPLIANCE NAMEPLATE.
DANgEr
APPLIANCES WITH NO CORD
PROVIDED BY FACTORY MUST
BE EQUIPPED WITH A CORD OF
SUFFICIENT LENGTH TO PERMIT
THE APPLIANCE TO BE MOVED
FOR CLEANING.
ELECTRICAL CONNECTIONS MUST
BE MADE BY A QUALIFIED SERVICE
TECHNICIAN IN ACCORDANCE WITH
APPLICABLE ELECTRICAL CODES.
simple control smokers • installation/operation/service manual - pg. 10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
ELEcTrIcAL cONNEcTION
ELEcTrIcAL - 767-SK
vOLTaGE
PHaSE
cycLE/Hz
aMPS
kW
cOrD & PLuG
120
1
60
16.0
1.9
nema 5-20p
20a - 125v plug
208-240 (agcy) 1
60
60
60
15.9
15.5
12.3
3.3
3.2
2.9
no cord
or plug
at 208
1
at 240
1
230
1
50/60
12.2
2.8
cee 7/7
220-230v plug
ELEcTrIcAL - 1767-SK
vOLTaGE
PHaSE
cycLE/Hz
aMPS
kW
cOrD & PLuG
208-240 (agcy) 1
60
60
60
30.8
31.0
24.6
6.4
6.5
5.9
no cord
or plug
at 208
1
at 240
1
230
1
50/60
24.3
5.6
no cord or plug
ELEcTrIcAL - 1000-SK-I
vOLTaGE
PHaSE
cycLE/Hz
aMPS
kW
cOrD & PLuG
208-240 (agcy) 1
60
60
60
31.4
30.7
24.3
6.5
6.4
5.8
no cord
or plug
at 208
at 240
1
1
230
1
50/60
24.1
5.5
no cord or plug
ELEcTrIcAL - 1000-SK/II
vOLTaGE
PHaSE
cycLE/Hz
aMPS
kW
cOrD & PLuG
208-240 (agcy) 1
60
60
60
15.7
15.3
12.1
3.3
3.2
2.9
no cord
or plug
at 208
1
at 240
1
230
1
50/60
12.2
2.8
cee 7/7
220-230v plug
Wire diagrams are located inside the bonnet of the unit.
simple control smokers • installation/operation/service manual - pg. 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPErATINg INSTrUcTIONS
USEr SAfETY INfOrMATION
The Alto-Shaam cook and hold oven is intended
for use in commercial establishments by qualified
operating personnel where all operators are
familiar with the purpose, limitations, and
associated hazards of this appliance. Operating
instructions and warnings must be read and
understood by all operators and users.
cAUTION
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN
IN OPERATION. TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
STArT-UP OPErATION
BEfOrE INITIAL USE:
PrEhEATINg:
Always preheat the oven for a minimum of 20
minutes before cooking product. Follow the
operating instructions indicated on the next page
of this manual.
Interior oven surfaces must be heated to remove
surface oils and the accompanying odor produced
during the first use of the oven.
1. Wipe all wire shelves, side racks and the full
oven interior with a clean, damp cloth. Install
the oven side racks, oven shelves, wood chip
tray, and external drip tray. Shelves are
installed with the curved edge toward the back
of the oven. Insert the drip pan on the interior
bottom surface of the oven.
DANgEr
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
2. Close the oven doors, press the power switch
to the ON position, and set the thermostat to
300°F (149°C).
SEVErE DAMAgE Or
ELEcTrIcAL hAZArD
cOULD rESULT.
3. Allow the oven to cycle for approximately 2
hours or until no odor is detected.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
cOOKINg OVEN chArAcTErISTIcS:
DANgEr
The oven is equipped with a special, high heat
density, heating cable. Through the Halo Heat
concept, the heating cable is mounted against
the walls of the cooking cavity to provide an
evenly applied, thermostatically controlled,
heat source. The design and operational
DIScONNEcT UNIT frOM
POwEr SOUrcE BEfOrE
cLEANINg Or SErVIcINg.
characteristics of the oven eliminate the need
for a moisture pan or a heat circulating fan.
Through even heat application, the quality of a
food product is maintained for many hours.
simple control smokers • installation/operation/service manual - pg. 12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPErATINg INSTrUcTIONS
5. Load wood chip container.
1. Push power switch to ON (I) position.
Control will display 0°F or 0°C.
Take one container load of dry wood chips and soak the
chips in water for 15 to 20 minutes. Shake excess water off
wood chips. Remove wood chip container from the interior
back panel of the smoker. Place the moistened chips in the
wood chip container and replace the container in the oven.
2. Set the holding temperature.
• Rotate the hold knob to the desired holding
temperature. The set temperature will appear in
.
the Digital Display
and the temperature
140F
display button will illuminate.
6. Set the Smoke Timer.
• The holding indicator light will illuminate while
The Smoke Timer activates the heating element located
within the wood chip container. When the wood chip
container is full and the smoking timer is turned clockwise
as far as it will turn, the wood chips will smoke for
approximately forty-five minutes to
in hold mode.
• Holding temperature range:
60° to 205°F (16 to 96°C)
3. Set the cooking temperature.
one hour.
• Rotate the cook knob to the desired temperature.
• To set the Smoke Timer, turn the smoking timer knob
past the required length of time, then immediately
bring it back to the correct setting.
The set temperature will appear in the Digital
.
Display
and the temperature display
250F
button will illuminate.
• Smoke Indicator Light will illuminate.
• The cooking indicator light will illuminate while
• Keep the oven door completely closed during the
in cook mode.
smoking cycle.
• Cooking temperature range:
Notes:
200° to 325°F (94 to 160°C)
• When the oven temperature reaches the set
• Note: Cooking mode not active unless timer
temperature, the heat indicator light will turn off.
is running.
• Press and hold the Temperature Display Button
4. Set timer.
for 3 seconds at any time to display the Actual oven
• Press Up or Down arrows when cook knob is set
.
temperature
.
190F
to begin cooking.
• Press Up or Down arrows to adjust the
To toggle between fahrenheit (°F) and celsius (°C):
time while cooking.
Press the Temperature Display Button at any time to display the
• Note: Hold timer button for 3 seconds
alternate temperature.
when in cook mode to cancel timer (display
----
The factory default is Fahrenheit. To change to Celsius:
shows
).
1. Press and hold the Temperature Display Button and the
5. PREHEAT oven for 30 minutes before
loading food. The heat indicator light will illuminate
and will remain lit as long as the oven
is calling for heat.
Down Arrow Key for 5 seconds.
.
2. The control will show
for 3 seconds to verify
C
selection and then show the temperature in ºC.
3. Repeat to toggle to Fahrenheit.
6. Load the oven with food and adjust cooking timer
as needed.
Note: With a power failure, factory test, etc., the control will retain
the ºC or ºF setting selected by the user when power is restored.
Heat
Indicator Light
Cooking
Indicator Light
Smoke
Indicator Light
Holding
Indicator Light
Digital
Display
I
o
Up/Down
Arrow Keys
On/Off
Power Switch
Hold Knob
Cook Knob
Smoke Timer
Temperature
Display Button
Time Key
simple control smokers • installation/operation/service manual - pg. 13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPErATINg INSTrUcTIONS
general holding guideline
hOLDINg TEMPErATUrE rANgE
fAhrENhEIT
Chefs, cooks and other specialized food service
personnel employ varied methods of cooking.
Proper holding temperatures for a specific food
product must be based on the moisture content of
the product, product density, volume, and proper
serving temperatures. Safe holding temperatures
must also be correlated with palatability in
determining the length of holding time for a
specific product.
MEAT
BEEF ROAST — Rare
BEEF ROAST — Med/Well Done
cELSIUS
130°F
54°C
155°F
68°C
BEEF BRISKET
CORN BEEF
PASTRAMI
160° — 175°F
160° — 175°F
160° — 175°F
130°F
71° — 79°C
71° — 79°C
71° — 79°C
54°C
PRIME RIB — Rare
STEAKS — Broiled/Fried
RIBS — Beef or Pork
VEAL
140° — 160°F
160°F
60° — 71°C
71°C
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
71° — 79°C
71° — 79°C
71° — 79°C
71° — 79°C
Halo Heat maintains the maximum amount
of product moisture content without the addition
of water, water vapor, or steam. Maintaining
maximum natural product moisture preserves the
natural flavor of the product and provides a more
genuine taste. In addition to product moisture
retention, the gentle properties of Halo Heat
maintain a consistent temperature throughout the
cabinet without the necessity of a heat distribution
fan, thereby preventing further moisture loss due to
evaporation or dehydration.
HAM
PORK
LAMB
POULTrY
CHICKEN — Fried/Baked
DUCK
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
71° — 79°C
71° — 79°C
71° — 79°C
71° — 79°C
TURKEY
GENERAL
fISh/SEAfOOD
FISH — Baked/Fried
LOBSTER
160° — 175°F
160° — 175°F
160° — 175°F
71° — 79°C
71° — 79°C
71° — 79°C
SHRIMP — Fried
BAKED gOODS
When product is removed from a high
BREADS/ROLLS
120° — 140°F
49° — 60°C
temperature cooking environment for immediate
transfer into equipment with the lower temperature
required for hot food holding, condensation can
form on the outside of the product and on the inside
of plastic containers used in self-service applications.
Allowing the product to release the initial steam
and heat produced by high temperature cooking
can alleviate this condition. To preserve the safety
and quality of freshly cooked foods, however, a
maximum of 1 to 2 minutes must be the only time
period allowed for the initial heat to be released
from the product.
MIScELLANEOUS
CASSEROLES
DOUGH — Proofing
EGGS —Fried
FROZEN ENTREES
HORS D'OEUVRES
PASTA
160° — 175°F
80° — 100°F
150° — 160°F
160° — 175°F
160° — 180°F
160° — 180°F
160° — 180°F
180°F
71° — 79°C
27° — 38°C
66° — 71°C
71° — 79°C
71° — 82°C
71° — 82°C
71° — 82°C
82°C
PIZZA
POTATOES
PLATED MEALS
SAUCES
140° — 165°F
140° — 200°F
140° — 200°F
160° — 175°F
60°— 74°C
60° — 93°C
60° — 93°C
71° — 79°C
SOUP
VEGETABLES
Most Halo Heat holding equipment is provided
with a thermostat control between 60° and 200°F
(16° to 93°C). If the unit is equipped with vents,
close the vents for moist holding and open the vents
for crisp holding.
THE HOLDING TEMPERATURES LISTED ARE SUGGESTED GUIDELINES ONLY. ALL
FOOD HOLDING SHOULD BE BASED ON INTERNAL PRODUCT TEMPERATURES.
ALWAYS FOLLOW LOCAL HEALTH (HYGIENE) REGULATIONS FOR ALL INTERNAL
TEMPERATURE REQUIREMENTS.
simple control smokers • installation/operation/service manual - pg. 14
Download from Www.Somanuals.com. All Manuals Search And Download.
cArE AND cLEANINg
cLEANINg AND PrEVENTIVE MAINTENANcE
PrOTEcTINg STAINLESS STEEL SUrfAcES
cLEANINg AgENTS
It is important to guard against corrosion
in the care of stainless steel
Use non-abrasive cleaning products designed for
use on stainless steel surfaces. Cleaning agents
must be chloride-free compounds and must not
contain quaternary salts. Never use hydrochloric
acid (muriatic acid) on stainless steel surfaces.
Always use the proper cleaning agent at the
manufacturer's recommended strength.
surfaces. Harsh, corrosive,
or inappropriate chemicals
can completely destroy the
protective surface layer
of stainless steel. Abrasive
pads, steel wool, or metal implements will abrade
surfaces causing damage to this protective coating
and will eventually result in areas of corrosion.
Even water, particularly hard water that contains
high to moderate concentrations of chloride, will
cause oxidation and pitting that result in rust
and corrosion. In addition, many acidic foods
spilled and left to remain on metal surfaces are
contributing factors that will corrode surfaces.
Contact your local cleaning supplier for
product recommendations.
cLEANINg MATErIALS
The cleaning function can usually be accomplished
with the proper cleaning agent and a soft, clean
cloth. When more aggressive methods must be
employed, use a non-abrasive scouring pad on
difficult areas and make certain to scrub with the
visible grain of surface metal to avoid surface
scratches. Never use wire brushes, metal scouring
pads, or scrapers to remove food residue.
Proper cleaning agents, materials, and
methods are vital to maintaining the appearance
and life of this appliance. Spilled foods should be
removed and the area wiped as soon as possible
but at the very least, a minimum of once a day.
Always thoroughly rinse surfaces after using a
cleaning agent and wipe standing water as quickly
as possible after rinsing.
cAUTION
TO PROTECT STAINLESS STEEL
SURFACES, COMPLETELY AVOID
THE USE OF ABRASIVE CLEANING
COMPOUNDS, CHLORIDE BASED
CLEANERS, OR CLEANERS
CONTAINING QUATERNARY SALTS.
NEVER USE HYDROCHLORIC ACID
(MURIATIC ACID) ON STAINLESS
STEEL. NEVER USE WIRE
BRUSHES, METAL SCOURING
PADS OR SCRAPERS.
simple control smokers • installation/operation/service manual - pg. 15
Download from Www.Somanuals.com. All Manuals Search And Download.
cArE AND cLEANINg
EQUIPMENT cArE
8. Remove excess water with sponge and wipe dry
with a clean cloth or air dry. Leave doors open
until interior is completely dry. Replace side
racks and shelves.
Under normal circumstances, this
oven should provide you with long
and trouble free service. There
is no preventative maintenance
required, however, the following
Equipment Care Guide will
9. Wipe door gaskets and control panel dry with a
clean, soft cloth.
maximize the potential life and trouble free
operation of this oven.
The cleanliness and appearance of this equipment
will contribute considerably to operating efficiency
and savory, appetizing food. Good equipment that
is kept clean works better and
10. Interior can be wiped with a sanitizing solution
after cleaning and rinsing. This solution must
be approved for use on stainless steel food
contact surfaces.
11. To help maintain the protective film coating on
polished stainless steel, clean the exterior of the
cabinet with a cleaner recommended for stainless
steel surfaces. Spray the cleaning agent on a
clean cloth and wipe with the grain of the
stainless steel.
lasts longer.
cLEAN DAILY
1. Disconnect unit from power
source and let cool.
12. Clean any glass with a window cleaner.
2. Remove all detachable items
such as wire shelves, side racks,
and drip pans. Clean these
items separately.
Always follow appropriate state or local health
(hygiene) regulations regarding all applicable cleaning
and sanitation requirements for equipment.
cLEAN ThE DOOr VENTS
3. Wipe the interior metal surfaces of the oven with a
paper towel to remove loose food debris.
Door vents need to be inspected and cleaned
as required.
4. Clean the interior metal surfaces of the cabinet
with a damp clean cloth or sponge and any good
commercial detergent.
chEcK OVErALL cONDITION Of
OVEN ONcE A MONTh
Check the oven once a month for physical damage and
loose screws. Correct any problems before they begin
to interfere with the operation of the oven.
NOTE: Avoid the use of abrasive cleaning
compounds, chloride based cleaners, or
cleaners containing quaternary salts. Never
use hydrochloric acid (muriatic acid) on
stainless steel.
DANgEr
5. Spray heavily soiled areas with a water soluble
degreaser and let stand for 10 minutes, then
remove soil with a plastic scouring pad.
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
6. Wipe control panel, door vents, door handles, and
door gaskets thoroughly since these areas harbor
food debris.
SEVErE DAMAgE Or
ELEcTrIcAL hAZArD
cOULD rESULT.
7. Rinse surfaces by wiping with sponge and clean,
warm water.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
DANgEr
DO NOT USE OVEN IF CONTROLS ARE NOT
PROPERLY FUNCTIONING
ENSURE POWER SOURCE
MATCHES VOLTAGE STAMPED
ON APPLIANCE NAMEPLATE.
Refer to the Trouble Shooting Guide located in this
manual or call an authorized service technician.
simple control smokers • installation/operation/service manual - pg. 16
Download from Www.Somanuals.com. All Manuals Search And Download.
SANITATION
Food flavor and aroma are usually so closely related that
The most accurate method of measuring safe temperatures
it is difficult, if not impossible, to separate them. There
is also an important, inseparable relationship between
cleanliness and food flavor. Cleanliness, top operating
efficiency, and appearance of equipment contribute
considerably to savory, appetizing foods. Good equipment
that is kept clean, works better and lasts longer.
of both hot and cold foods is by internal product
temperature. A quality thermometer is an effective tool for
this purpose, and should be routinely used on all products
that require holding at a specific temperature.
A comprehensive sanitation program should focus on
the training of staff in basic sanitation procedures. This
includes personal hygiene, proper handling of raw foods,
cooking to a safe internal product temperature, nd the
routine monitoring of internal temperatures from receiving
through service.
Most food imparts its own particular aroma and many
foods also absorb existing odors. Unfortunately, during
this absorption there is not distinction between GOOD
and BAD odors The majority of objectionable flavors and
odors troubling food service operations are caused by
bacteria growth. Sourness, rancidity, mustiness, stale or
other OFF flavors are usually the result of germ activity.
Most food-borne illnesses can be prevented through
proper temperature control and a comprehensive
program of sanitation. Both these factors are important
to build quality service as the foundation of customer
satisfaction. Safe food handling practices to prevent food-
borne illness is of critical importance to the health and
safety of your customers.
The easiest way to insure full, natural food flavor is
through comprehensive cleanliness. This means good
control of both visible soil (dirt) and invisible soil
(germs). A through approach to sanitation will provide
essential cleanliness. It will assure an attractive
appearance of equipment, along with maximum efficiency
and utility. More importantly, a good sanitation program
provides one of the key elements in the prevention of
food-borne illnesses.
HACCP, an acronym for Hazard Analysis (at) Critical
Control Points, is a quality control program of operating
procedures to assure food integrity, quality, and safety.
Taking steps necessary to augment food safety practices
is both cost effective and relatively simple. While HACCP
guidelines go far beyond the scope of this manual,
additional information is available by contacting:
A controlled holding environment for prepared foods is
just one of the important factors involved in the prevention
of food-borne illnesses. Temperature monitoring and
control during receiving, storage, preparation, and the
service of foods are of equal importance.
CENTER FOR FOOD SAFETY AND APPLIED
NUTRITION FOOD AND DRUG ADMINISTRATION
1-888-SAFEFOOD
INTERNAL FOOD PRODUCT TEMPERATURES
HOT FOODS
40° TO 140°F
70° TO 120°F
140° TO 165°F
DANGER ZONE
CRITICAL ZONE
SAFE ZONE
(4° TO 60°C)
(21° TO 49°C)
(60° TO 74°C)
COLD FOODS
ABOVE 40°F
36° TO 40°F
DANGER ZONE
SAFE ZONE
(ABOVE 4°C)
(2° TO 4°C)
FROZEN FOODS
ABOVE 32°F
0° TO 32°F
DANGER ZONE
CRITICAL ZONE
SAFE ZONE
(ABOVE 0°C)
(-18° TO 0°C)
0°F or below
(-18°C or below)
simple control smokers • installation/operation/service manual - pg. 17
Download from Www.Somanuals.com. All Manuals Search And Download.
SErVIcE
TrOUBLE ShOOTINg chEcKLIST
Error
code Description
Possible cause
Cavity air sensor reading < 5°F. Verify sensor integrity.
See sensor test instructions below.
E-10 cavity air sensor shorted
E-11 cavity air sensor open
Cavity air sensor reading > 517°F. Verify sensor integrity.
See sensor test instructions below.
Product probe is shorted
E-20
Product probe reading < 5°F. Verify sensor integrity.
See sensor test instructions below.
Oven will cook in time only
Product probe is open
E-21
Product Probe reading > 517°F. Verify sensor integrity.
See sensor test instructions below.
Oven will cook in time only
E-30 Under temperature
Unit has not reached set-point for more than 90 minutes.
Unit has been higher than 25°F above the maximum cavity set-point for
more than 2 minutes. Note: Holding Cabinets with this error code are
more than 145°F higher than the maximum set-point.
E-31 Over temperature
E-50 Temp. measurement error
E-51 Temp. measurement error
E-60 real time clock error
E-61 real time clock error
Contact factory.
Contact factory.
Data set to factory default. Ensure that date and time are correct if applicable.
Contact factory.
Refer to wiring diagram for the particular model and ensure dip switches on
the control match the settings called out on the WD. If the dip switch settings
are correct according to the print replace the control.
configuration connector
E-70
error (DIP switch)
Voltage below 90 VAC on a 125 VAC unit, or below 190 VAC on a
208-240 VAC unit. Correct voltage.
E-78 Voltage low
E-79 Voltage high
E-80 EEPrOM Error
Voltage over 135 VAC on a 125 VAC unit, or over 250 VAC on a
208-240 VAC unit. Correct voltage.
Ensure that all temperatures and times are properly set.
Contact factory if problem persists.
E-81 EEPrOM Error
E-82 EEPrOM Error
E-83 EEPrOM Error
E-85 EEPrOM Error
Contact factory.
Contact factory.
Contact factory.
All timers, if previously on, are now off. Possible bad EEPROM.
Stored HACCP memory corrupted. HACCP Address reset to 1. Possible bad
EEPROM. Contact factory if problem persists.
E-86 EEPrOM Error
E-87 EEPrOM Error
E-88 EEPrOM Error
E-90 Button stuck
E-dS Datakey error
Stored offsets corrupted. Offsets reset to 0. Control may need a recalibration.
Possible bad EEPROM. Contact factory if problem persists.
All timer set-points are reset to 1 minute. Timers, if previously on, are now
off. Possible bad EEPROM.
A button has been held down for >60 seconds. Adjust control. Error will
reset when the problem has been resolved.
Datakey digital signature incompatible. Cycle power, and install compatible
Datakey if error persists.
E-dT Datakey error
Datakey incompatible with control. Install compatible Datakey.
Install Datakey and cycle power to control to clear error.
E-dU Datakey unplugged
Note: If in doubt, always cycle the power to the control and contact factory if the problem persists.
To test probe and air sensor:
Test probe and air sensor by placing sensor in ice water bath and using an ohmmeter set on the ohm scale. The
reading should be 100 ohms resistance. If it is more than 2 ohms higher or lower, sensor needs to be replaced.
simple control smokers • installation/operation/service manual - pg. 18
Download from Www.Somanuals.com. All Manuals Search And Download.
SErVIcE
SErVIcE VIEw - single compartment (1000-SK/II Shown)
A
34
35
36
1
DETAIL A
37
2
3
6
4
31
33
7
30
5
29
28
27
A
32
26
25
24
23
22
8
9
21
10
11
18
20
15
14
19
12
18
17
16
13
Part numbers and drawings are subject to change without notice.
DANgEr
DANgEr
LOcK-OUT Or POST
BrEAKEr PANEL UNTIL
SErVIcE wOrK hAS
BEEN cOMPLETED.
DIScONNEcT UNIT frOM
POwEr SOUrcE BEfOrE
cLEANINg Or SErVIcINg.
simple control smokers • installation/operation/service manual - pg. 19
Download from Www.Somanuals.com. All Manuals Search And Download.
SErVIcE PArTS LIST - single compartment
MODEL >
767-SK
1000-SK/II
ITEM
1
2
3
4
5
6
7
8
DEScrIPTION
PArT NO. QTY PArT NO. QTY
A
TOP COVER
PLUG, HOLE 3/8"
1011872
PG-25574
PG-28439
BU-3964
GS-23622
IN-2003
1
1
6
1
1
1
1
6
1
2
2
2
2
1
1
1
1
6
2
10
1
1
1
2
1
1
1
2
2
2
2
3
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
2
2
2
1
2
2
2
33
1
2
1011534
PG-25574
PG-28439
BU-3964
GS-23622
IN-2003
1
1
6
1
1
1
1
6
1
2
2
2
2
1
1
1
1
6
2
6
1
1
1
2
1
1
1
2
1
2
—
3
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
2
2
2
1
2
2
2
29
1
2
PLUG, DOME, 187" HOLE
BUSHING, STRAIGHT, STRAIN RELIEF
GASKETS, ADHESIVE,.125X.375 [linear ft]
INSULATION
REAR TRIM, SPOT
RIVET, BLIND, #44, STNLS
SWITCH COVER
5014137
RI-2100
5014204
RI-2100
9
11133
11133
10
11
12
13
14
15
SIDE PANEL
1011871
CR-34646
CS-24874
CS-24875
1010394
5010391
1010584
1010585
SC-2072
HG-22338
SC-2073
5011828
5011829
GS-22951
SC-2071
HD-27080
13947
1011619
CR-34646
CS-24874
CS-24875
1009941
5009716
1010189
1010188
SC-2072
HG-22338
SC-2073
5013154
5013155
GS-22952
SC-2071
HD-27080
13947
CONNECTOR-5 CONDUCTOR
CASTER, 1.5" STEM, RIGID 5"
CASTER, 1.5" STEM, 5" SWIVEL WITH BRAKE
BOTTOM PANEL
DRIP TRAY KIT
- DRIP TRAY
- DRIP TRAY BRACKET
SCREW, 10-32 X 3/4", NF PHIL, FLAT M/S, 18-8 S/S
HINGE, 1-3/8" OFFSET, PAIR, CHROME
SCREW, 10-32 X 1-1/2", NF, PHIL,FLAT M/S,18-8 S/S
DOOR ASSEMBLY, RH
DOOR ASSEMBLY, LH
16
17
18
19
DOOR GASKET
20
21
22
23
24
25
26
SCREW, 10-32 X 3/4" PHILLIPS PAN HD
HANDLE, OFFSET MAGNETIC LATCH
SHIM, HANDLE
DRIP PAN WELD
14831
5005616
SH-2325
SH-29474
SR-2266
—
SHELF, WIRE S/S
SHELF, RIB RACK
SH-2324
SH-2743
SR-28405
1010813
KN-26568
SW-34769
PE-29361
CC-34488
TT-34910
TR-34539
TR-34540
CB-34945
SC-22924
WS-22297
WS-22302
NU-22770
1010409
4652R
SIDE RACKS
PAN SLIDES
KNOB
27
28
29
30
31
32
KN-26568
SW-34769
PE-29383
CC-34488
TT-34910
TR-34539
TR-34540
CB-34945
SC-22924
WS-22297
WS-22302
NU-22770
1011813
4652R
SWITCH, ROCKER, 20A
PANEL OVERLAY
CONTROL
THERMOSTAT, COOK
TIMER, 1 HR, 208-240V
TIMER, 1 HR, 120V
33
34
35
36
37
CABLE HARNESS
SCREW, HHCS, M6 X 20
WASHER, FLAT, M6, DIN 125
WASHER, M6 SPLIT LOCK S/S 18-8
NUT, THREADED INSERT, M6
ELEMENT COVER, SMOKE
CHIP TRAY WELD
BRACKET, PILOT LIGHT
NON-PRODUCT PROBE SEAL
BRACKET, SENSOR MOUNTING
BACK CASING
SMOKE HEATER PLATE WELD
BLOCK, SENSOR
BLOCK, TERMINAL, PORCELAIN
BRACKET, CHIP TRAY
BUSHING, BLACK, 5/8" SNAP
CONNECTOR
38*
39*
40*
41*
42*
43*
44*
45*
46*
47*
48*
49*
50*
1004360
1006871
1008272
1010393
5003782
BK-27878
BK-33546
BT-29217
BU-3611
CR-34559
FA-3973
FA-34524
LI-3951
1004360
1006871
1008272
1011878
5003782
BK-27878
BK-33546
BT-29217
BU-3611
CR-34559
FA-3973
FA-34524
LI-3951
FAN, BOX, 120V
FAN BOX, 208-240V, 230V
PILOT LIGHT, 208-240V
PILOT LIGHT, 120V
51*
LI-3027
LI-3027
52*
53*
54*
55*
56*
57*
58*
59*
60*
61*
NUT, HEX M4-0.7 18-8
NU-22286
NU-2296
NU-2437
PR-34494
SC-2239
SC-23154
SC-2425
SC-2459
SW-3528
WS-22300
NU-22286
NU-2296
NU-2437
PR-34494
SC-2239
SC-23154
SC-2425
SC-2459
SW-3528
WS-22300
NUT, HEX #8-32
NUT, 1/4-20 HEX S/S
SENSOR, OVEN TEMPERATURE
SCREW, 6-32 X 1/2", NC PHIL, FLAT
SCREW, 8-32 X 2" SLOT PAN HEAD 18-8 S/S
SCREW, 8-32 X 1/2" PHIL SCREW
SCREW, 8-32 x 1/4" PHIL
SWITCH, TOGGLE, VOLTAGE
WASHER, M4 SPLIT LOCK S/S 18-8
*not shown
simple control smokers • installation/operation/service manual - pg. 20
Download from Www.Somanuals.com. All Manuals Search And Download.
SErVIcE
EXTErIOr VIEw - double compartment (1000-sK-i Shown)
B
40
1
5
41
39
2
38
42
3
37
43
31
4
36
35
7
6
DETAIL A
34
8
33
32
30
A
9
29
28
10
27
11
26
25
12
24
13
20
23
16
22
17
15
14
21
20
19
Part numbers and drawings are
subject to change without notice.
18
DANgEr
DANgEr
BrEAKEr PANEL UNTIL
SErVIcE wOrK hAS
BEEN cOMPLETED.
LOcK-OUT Or POST
DIScONNEcT UNIT frOM
POwEr SOUrcE BEfOrE
cLEANINg Or SErVIcINg.
simple control smokers • installation/operation/service manual - pg. 21
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTErIOr PArTS LIST - double compartment
MODEL >
1767-SK
1000-SK-I
ITEM
1
2
3
4
5
6
7
8
DEScrIPTION
PArT NO. QTY PArT NO. QTY
B
TOP COVER
PLUG, HOLE 3/8"
1011872
PG-25574
SC-23670
NU-2215
GS-23622
BT-26884
BU-3964
5014223
IN-2003
1
2
4
4
1
1
1
1
2
2
1
2
2
2
2
1
1
12
2
20
2
1
4
2
2
1
1
1
2
4
4
4
3
1
1
1
1
1
1
1
3
4
1
2
2
1
2
1
2
2
1
1
1
1
1
2
8
4
2
1
2
2
4
2
12
4
6
16
34
1
2
1011534
PG-25574
SC-23670
NU-2215
GS-23622
BT-26884
BU-3964
5014293
IN-2003
1
2
4
4
1
1
1
1
2
2
1
3
2
2
2
1
1
12
2
20
2
2
4
2
2
1
1
1
2
4
—
4
3
1
1
1
1
1
1
1
3
4
1
2
2
1
2
1
3
3
1
2
1
3
1
2
8
4
2
1
2
2
4
3
12
6
8
20
41
1
2
SCREW, 10-32 X 1/2", NF PHIL, FLAT
NUT, 10-32 UNF HEX MS, 18-8 SST
GASKETS, ADHESIVE, .125 X .375 [linear ft]
BRACKET, TETHER
BUSHING, STRAIGHT, STRAIN RELIEF
REAR TRIM
9
INSULATION
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
ELEMENT COVER, SMOKER
SWITCH COVER
CONNECTOR-5 CONDUCTOR
SIDE PANEL
CASTER, 1.5" STEM, RIGID 5"
CASTER, 1.5" STEM, 5" SWIVEL WITH BRAKE
BOTTOM PANEL
MIDDLE BONNET ASSEMBLY
SCREW, 10-32 X 3/4", NF PHIL, FLAT M/S, 18-8 S/S
HINGE, 1-3/8" OFFSET, PAIR, CHROME
SCREW, 10-32X1-1/2", NF, PHIL, FLAT M/S,18-8 S/S
DRIP PAN WELD
1010409
11133
1011813
11133
CR-34646
1012652
CS-24874
CS-24875
1010394
5013052
SC-2072
HG-22338
SC-2073
14831
CR-34646
1011533
CS-24874
CS-24875
1009941
5013230
SC-2072
HG-22338
SC-2073
5005616
5012859
SC-2071
HD-27080
13947
DOOR ASSEMBLY
5011828
SC-2071
HD-27080
13947
SCREW, 10-32 X 3/4" PHILLIPS PAN HD
HANDLE, OFFSET MAGNETIC LATCH
SHIM, HANDLE
DRIP TRAY KIT
- DRIP TRAY
5010391
1010584
1010585
SH-2743
SR-28405
1010813
SH-2324
KN-26568
SW-34769
PE-29361
CC-34488
TT-34910
TR-34539
CB-34945
5014319
FA-34524
PG-28439
SC-22924
WS-22297
WS-22302
NU-22770
4652R
5009716
1010189
1010188
SH-29474
SR-2266
—
- DRIP TRAY BRACKET
SHELF, RIB RACK
27
28
SIDE RACK
PAN SLIDES, 230V ONLY
SHELF, WIRE S/S
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44*
45*
46*
47*
48*
49*
50*
51*
52*
53*
54*
55*
56*
57*
58*
59*
60*
61*
62*
63*
64*
65*
66*
67*
68*
SH-2325
KN-26568
SW-34769
PE-29383
CC-34488
TT-34910
TR-34539
CB-34945
5014319
FA-34524
PG-28439
SC-22924
WS-22297
WS-22302
NU-22770
4652R
KNOB
SWITCH, ROCKER, 20A
PANEL OVERLAY
CONTROL
THERMOSTAT, COOK
TIMER, 1 HR
CABLE WIRE HARNESS
ELECTRIC CHASSIS
FAN, BOX, 208-240V, 230V
PLUG, DOME, 187" HOLE
SCREW, HHCS, M6 X 20, W/NO MARKING
WASHER, FLAT, M6, DIN 125
WASHER, M6 SPLIT LOCK S/S 18-8
NUT, THREADED INSERT, M6
CHIP TRAY WELD
BRACKET, PILOT LIGHT
NON-PRODUCT PROBE SEAL
BRACKET, SENSOR MOUNTING
AIR SHIELD
1004360
1006871
1008272
1011925
5003782
5014325
BK-27878
BK-33546
BT-29217
BU-3378
BU-3611
CR-34559
LI-3951
1004360
1006871
1008272
1011925
5003782
5014315
BK-27878
BK-33546
BT-29217
BU-3378
BU-3611
CR-34559
LI-3951
SMOKE HEATER PLATE WELD
CABLE INSULATION
BLOCK, SENSOR
BLOCK, TERMINAL, PORCELAIN
BRACKET, CHIP TRAY
BUSHING, SNAP 1-1/8"
BUSHING, BLACK, 5/8" SNAP
CONNECTOR
PILOT LIGHT
NUT, HEX M4-0.7 18-8
NU-22286
NU-2296
NU-2437
PR-34494
RI-2100
NU-22286
NU-2296
NU-2437
PR-34494
RI-2100
NUT, HEX #8-32
NUT, 1/4-20 HEX S/S
SENSOR, OVEN TEMPERATURE
RIVET, BLIND, #44, S/S
SCREW, 6-32 X 1/2", NC PHIL, FLAT
SCREW, 8-32 X 2" SLOT PAN HEAD 18-8 S/S
SCREW, 8-32 X 1/2" PHIL SCREW
SCREW, 8-32 X 1/4" PHIL
SWITCH, TOGGLE, VOLTAGE
WASHER M4 SPIT LOCK S/S 18-8
SC-2239
SC-23154
SC-2425
SC-2459
SW-3528
WS-22300
SC-2239
SC-23154
SC-2425
SC-2459
SW-3528
WS-22300
*not shown
simple control smokers • installation/operation/service manual - pg. 22
Download from Www.Somanuals.com. All Manuals Search And Download.
SErVIcE
ELEcTrONIc cOMPONENTS - 767-sK, 120V shown
6
3
1
2
4
5
7
8
13
11
9
10
12
Part numbers and drawings are subject to change without notice.
ITEM
DEScrIPTION
PArT NO. QTY ITEM
DEScrIPTION
CONNECTOR, FERRULE #18
ELEMENT SMOKE, 208-240V, 230V
ELEMENT, SMOKE, 120V
PArT NO. QTY
1
2
3
4
5
6
STAR LOCK WASHER
WS-2467
SC-2190
5014097
BU-3419
CR-34830
CD-3397
CD-3922
BK-3019
SC-2365
1
1
1
1
3
1
1
1
2
9
CR-34827
EL-35022
EL-35023
CR-34638
LI-3951
2**
1**
1**
2
GROUND SCREW
10
ELECTRIC CHASSIS
BUSHING, 3/8 BLACK HOLE
CONNECTOR, FERRULE #12
CORDSET, 120V
11
12
CONNECTOR, qUICK DISCONNECT
PILOT LIGHT, WHITE, 110V
BUSHING, 1/2 HOLE
1
13
BU-3006
FI-33225
SC-2459
1
CORDSET, 230V
14*
15*
LINE FILTER (230V ONLY)
1
7
8
T-BLOCK
SCREW, LINE FILTER (230V ONLY)
2
SCREW, 6-32 X 1-1/4 ROUND HD
*not shown
**quantity per compartment
DANgEr
DANgEr
LOcK-OUT Or POST
BrEAKEr PANEL UNTIL
SErVIcE wOrK hAS
BEEN cOMPLETED.
DIScONNEcT UNIT frOM
POwEr SOUrcE BEfOrE
cLEANINg Or SErVIcINg.
simple control smokers • installation/operation/service manual - pg. 23
Download from Www.Somanuals.com. All Manuals Search And Download.
SErVIcE
MID BONNET ASSEMBLY - 1767-SK shown
2
3
1
5
6
4
7
8
16
9
10
15
11
12
14
13
Part numbers and drawings are subject to change without notice.
ITEM
DEScrIPTION
MID-BONNET SPOT ASSB
CONTROL
PArT NO. QTY ITEM
DEScrIPTION
PArT NO. QTY
1
2
3
4
5
6
7
8
5012422
CC-34488
NU-2296
1
1
2
2
2
1
1
1
9
NUT, HEX #8-32
NU-2296
1004360
LI-3951
2
1
1
2
2
3
1
1
10
11
12
13
14
15
16
BRACKET, PILOT LIGHT MTG
PILOT LIGHT, WHITE, 250V
CONNECTOR-5 CONDUCTOR
SCREW, 8-32 X 1/2", PHIL
KNOB, T-STAT CONTROL
NUT, M4-0.7 HEX 18-8
WASHER, M4 SPLIT LOCK S/S 18-8
CONNECTOR
WS-22300
CR-34559
CB-34945
TT-34910
TR-34539
CR-34646
SC-2425
KN-26568
SW-34769
PE-29441
CABLE, WIRE HARNESS
THERMOSTAT,COOK
TIMER, 1HR, 208/240V
SWITCH, ROCKER, 125-277V,20A
OVERLAY, MID BONNET CONTROL
cABLE hEATINg KITS
#4878
120V
#4881
208-240V
230V
cABLE hEATINg KIT >
(one kit required per cavity)
ITEM
DEScrIPTION
QTY
QTY
210 FT.
12
CB-3045
CR-3226
IN-3488
BU-3105
BU-3106
ST-2439
NU-2215
SL-3063
TA-3540
CABLE HEATING ELEMENT
112 FT.
RING CONNECTOR
INSULATION CORNER
SHOULDER BUSHING
CUP BUSHING
6
1 FT.
1 FT.
12
6
6
12
STUD
6
12
12
HEX NUT
24
INSULATING SLEEVE
ELECTRICAL TAPE
6
12
1 ROLL
1 ROLL
DANgEr
DANgEr
LOcK-OUT Or POST
BrEAKEr PANEL UNTIL
SErVIcE wOrK hAS
BEEN cOMPLETED.
DIScONNEcT UNIT frOM
POwEr SOUrcE BEfOrE
cLEANINg Or SErVIcINg.
simple control smokers • installation/operation/service manual - pg. 24
Download from Www.Somanuals.com. All Manuals Search And Download.
simple control smokers • installation/operation/service manual - pg. 25
Download from Www.Somanuals.com. All Manuals Search And Download.
simple control smokers • installation/operation/service manual - pg. 26
Download from Www.Somanuals.com. All Manuals Search And Download.
simple control smokers • installation/operation/service manual - pg. 27
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSPORTATION DAMAGE and CLAIMS
All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments
become the property of the consignee.
Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases,
the carrier is assumed to be responsible for the safe delivery of the merchandise, unless negligence can be
established on the part of the shipper.
1. Make an immediate inspection while the equipment is still in the truck or immediately after it is moved to the receiving area.
Do not wait until after the material is moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until you have made a proper count and inspection of all merchandise received.
3. Note all damage to packages directly on the carrier’s delivery receipt.
4. Make certain the driver signs this receipt. If he refuses to sign, make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the following on the delivery receipt:
Driver refuses to allow inspection of containers for visible damage.
6. Telephone the carrier’s office immediately upon finding damage, and request an inspection. Mail a written confirmation of the
time, date, and the person called.
7. Save any packages and packing material for further inspection by the carrier.
8. Promptly file a written claim with the carrier and attach copies of all supporting paperwork.
We will continue our policy of assisting our customers in collecting claims which have been properly filed and actively pursued.
We cannot, however, file any damage claims for you, assume the responsibility of any claims, or accept deductions in payment
for such claims.
LIMITED WARRANTY
Alto-Shaam, Inc. warrants to the original purchaser only that any original part that is found to be defective in material or workmanship will, at
Alto-Shaam's option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part.
The parts warranty period is as follows:
For the refrigeration compressor on Alto-Shaam Quickchillers™, five (5) years from the date of installation.
For the heating element on Halo Heat® cooking and holding ovens, as long as the original purchaser owns the oven. This
excludes holding only equipment.
For all other parts, one (1) year from the date of installation or fifteen (15) months from the shipping date, whichever occurs first.
The labor warranty period is one (1) year from the date of installation or fifteen (15) months from the shipping date, whichever occurs first.
Alto-Shaam will bear normal labor charges performed during standard business hours, excluding overtime, holiday rates or any
additional fees.
To be valid, a warranty claim must be asserted during the applicable warranty period. This warranty is not transferable.
THIS WARRANTY DOES NOT APPLY TO:
1. Calibration.
2. Replacement of light bulbs, door gaskets, and/or the replacement of glass due to damage of any kind.
3. Equipment damage caused by accident, shipping, improper installation or alteration.
4. Equipment used under conditions of abuse, misuse, carelessness or abnormal conditions, including but not limited to, equipment
subjected to harsh or inappropriate chemicals, including but not limited to, compounds containing chloride or quaternary salts, poor water
quality, or equipment with missing or altered serial numbers.
5. Damage incurred as a direct result of poor water quality, inadequate maintenance of steam generators and/or surfaces affected by water
quality. Water quality and required maintenance of steam generating equipment is the responsibility of the owner/operator.
6. Damage caused by use of any cleaning agent other than Alto-Shaam's Combitherm® Cleaner, including but not limited to damage due to
chlorine or other harmful chemicals. Use of Alto-Shaam's Combitherm® Cleaner on Combitherm® ovens is highly recommended.
7. Any losses or damage resulting from malfunction, including loss of product, food product, revenue, or consequential or incidental
damages of any kind.
8. Equipment modified in any manner from original model, substitution of parts other than factory authorized parts, removal of any parts
including legs, or addition of any parts.
This warranty is exclusive and is in lieu of all other warranties, express or implied, including the implied warranties of merchantability and
fitness for a particular purpose. In no event shall Alto-Shaam be liable for loss of use, loss of revenue or profit, or loss of product, or for any
indirect, special, incidental, or consequential damages. No person except an officer of Alto-Shaam, Inc. is authorized to modify this warranty
or to incur on behalf of Alto-Shaam any other obligation or liability in connection with Alto-Shaam equipment.
Effective November 1, 2011
RECORD THE MODEL AND SERIAL NUMBER OF THE APPLIANCE FOR EASY REFERENCE.
ALWAYS REFER TO BOTH MODEL AND SERIAL NUMBER IN ANY CONTACT WITH ALTO-SHAAM REGARDING THIS APPLIANCE.
Model: ______________________________________________ Date Installed: ______________________________________________________
Voltage: ______________________________________________ Purchased From: ___________________________________________
Serial Number: _____________________________________________________________________________________________________________
G
G
G
W164 N9221 Water Street P.O. Box 450 Menomonee Falls, Wisconsin 53052-0450 U.S.A.
PHONE: 262.251.3800 • 800.558-8744 USA/CANADA FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
PRINTED IN U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|