Beko Dishwasher DL1243 User Manual

��

Dishwasher

DL1243

�

��

�

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

1 Know your dishwasher

/ specification

6 Operating the dishwasher 20

7 How to clean your machine 20

Hot Air Drying

Upper spray arm

Lower spray arm

2 Warning and safety

information

Electrical Safety

Children’s Safety

General

Recycling

Energy and water saving

What should not be washed in your

dishwasher

8 Before calling service

/ Trouble shooting

3 Before first use

Electrical requirements

4 Installation

Warning

This appliance must be earthed

Important

Fitting a different plug

Water inlet hose connection

Drain Hose Connection

5 How to use

Water hardness & regeneration

settings

Water Hardness Level Adjustment

Table

Adding Dishwasher Salt

Detergent use

Filling detergent dispenser

Rinse aid

Loading the dishwasher

Folding plate support rods

Movable Cutlery Basket

Upper basket with variable height

setting

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Know your dishwasher / specification

��

Salt Indicator Light

On / Off Indicator Light

& Progress Indicator Lights

Programme Starting Point

Time Delay Indicator

Time Delay Button

On / Off Button

Start / Stop Button

Half Load Button

Programme Knob

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Specification

Load Capacity

Height

: 12 Place settings

: 850 mm

Width

: 598 mm

Depth

: 598 mm

Depth/Height

(without worktop)

Net weight

: 570 mm / 820 mm

: 44 kg

Supply voltage

Fuse currrent

Total power

: 220-240 V ~ 50 Hz

: 13 A

: 1900-2200 W

: 1800 W

Heater power

Pump powers

Diameter of plates for :

Upper basket

Lower basket

: 125/30 W

: 25 cm max.

: 31 cm max.

Because we continually strive to improve our products, we may change our

specifications and designs without prior notice.

Note for Testing Institutes

The necessary information for performance testing will be provided upon request.

The request can be done by e-mail through:

[email protected]

Please do not forget to write the model code ,stock code and serial number

information of the appliance besides your contact information in the e-mail.

The model code, stock code and serial number information can be found on the

rating label, which is placed on the side of the door.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Warning and safety information

Never allow your children to play on or

sit onto the front door when the front

door is open.

Electrical Safety

The dishwasher should only be

operated on the voltage specified. For

electrical safety, only earthed plugs

and sockets should be used. Always

use the fused plug provided with the

appliance. The user is responsible

for meeting these basic safety

requirements. The life of your machine

and your safety depend on you using

an electrical installation compliant to

standards.

After unpacking your machine, keep

the packing material out of children’s

reach.

Warning !

Long cutlery, such as ladles and

long knives, etc must be placed

horizontally on top of the full cutlery

basket or on the racks to prevent

accidental injury.

Do not use an extension cable.

When disconnecting your machine

from the mains supply, always pull from

the plug. Never pull the cord itself.

General

This dishwasher has been designed to

clean your dirty dishes at home.

Never use chemical solvents in your

machine; this may lead to explosion

risk.

Children’s Safety

Never allow your children to play with

your dishwasher.

Never use materials other than

specially produced softening salts in

the salt dispenser of your machine.

Dishwasher detergents contain irritants

and abrasives. These ingredients might

have caustic effects in the eyes, mouth

and throat.

Never use materials other than

specially produced detergents and

rinse-aids in the detergent and rinse

aid dispensers of your machine.

They can be extremely dangerous if

swallowed. Avoid contact with skin

and eyes. Check that the detergent

receptacle is empty after completion of

the wash cycle.

Please dispose of the packaging

material and old appliances carefully.

Please ensure old machines do not

become a threat to child safety. It is

known that children lock themselves

in unused machines. To avoid such a

problem it is advised that you cut the

mains cable off and break the door

latch so it does not lock.

Keep detergents out of children’s

reach and do not put detergent in the

machine until right before you start the

washing programme.

The water in your dishwasher is not

suitable for drinking, for this reason

do not allow your children near your

machine when the front door is open.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

The door of your machine is designed

to support the weight of a full basket

when the lower basket is pulled all the

way out. Never place any other load

on the door, otherwise the machine

may tip over.

human health due to the presence of

hazardous substances.

Energy and water saving

Scrape excess food from the dishes

before loading. Start your dishwasher

after fully loading the machine. Do not

use the pre-wash programme unless

required. Make your programme

After using the dishwasher always

close the door as an open door can be

a hazard.

selection as per the programme chart

and quick reference guide supplied.

Do not open the door whilst the

appliance is in operation.

What should not be washed in

your dishwasher

Recycling

Do not wash items soiled with cigarette

ash, candle/paint wax, dyes, chemicals

etc. since these may damage your

machine

Please help us to protect our

environment. Packing materials and

some parts of your machine are

produced using recyclable materials.

These materials are marked up with

recycling symbol and material type

information (>PE<, >PS<, >POM< …).

These raw materials should not be

mixed with general refuse and should

be given to recycling centers.

We suggest you contact your local

authority for disposal information and

facilities available.

Do not wash forks, knives and spoons

with wooden or bone handles, items

stuck together with adhesives,

plastic items not resistant to high

temperatures. Copper, tin items and

aluminium ware in your dishwasher.

As with hand washing, some “on-

glaze” decorated china, aluminum or

silver have a tendency to discolour or

fade. Also, certain types of glassware

and crystals may lose their shine and

become opaque in time.

This product bears the

selective sorting symbol

for waste electrical and

electronic equipment

(WEEE).

A chemical reaction can occur between

silver cutlery and stainless steel

cutlery. As a precaution, do not wash

together.

This means that this product must

be handled pursuant to European

Directive 2002/96/EC in order to be

recycled or dismantled to minimize its

impact on the environment. For further

information, please contact your local

or regional authorities.

Iron and cast iron objects can rust and

stain other items.

Pay special attention to whether or not

the item you wash in the dishwasher is

dishwasher-proof.

Electronic products not included in the

selective sorting process are potentially

dangerous for the environment and

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

If in doubt, contact the manufacturer of

the item.

Installation

When deciding on where to install

your new dishwasher, ensure that the

position of your dishwasher makes it

easy and quick for you to place the

dishes in the dishwasher and also to

take them out and store away after the

dishwashing is completed.

Do not overload your dishwasher or

do not load items other than those

mentioned in this manual.

Before first use

After unpacking your dishwasher,

check the machine against any

Avoid placing the dishwasher where

the ambient temperature is likely to fall

below. 5 degrees C. (41° F)

possible transportation damage. Never

install and use damaged machines. If

your machine is damaged contact your

retailer. Always have your machine

installed by qualified electrician/

When positioning your appliance, take

care not to damage your flooring, pipes

wall coverings etc. Do not move the

appliance by pulling by the door or

handle

plumber to ensure correct installation.

Any repairs and maintenance work

on this dishwasher should be carried

out by authorised service staff only.

Unauthorised repairs are not only

dangerous, but also lead to the

cancellation of your warranty.

Electrical requirements

Before you insert the plug into the wall

socket make sure that the voltage and

the frequency shown in the rating label

corresponds to your electricity supply.

If your dishwasher has an Internal

Lighting; incase of a defect broken

lamps can be changed by an

authorized service technican.

We recommend that this appliance be

connected to the mains supply via a

suitable switched and fused socket in a

readily accessible position.

Make sure the electricity and water

connections of your dishwasher are

in compliance with the instructions for

assembly as stated in the relevant part

of this booklet.

If the supply cord or the mains lead

is damaged please do not replace it

yourself. The supply cord or the mains

lead must be replaced by a Beko

Authorised Service Agent or a similarly

qualified person.

It is recommended that the

dishwasher is operated on the

Economy programme with prewash

before loading with dishes.

Before the first wash, add 1 Litre of

water to the salt container of your

machine.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

3. Connect the brown (live) wire to

the terminal in the plug marked ‘L’

or coloured red.

Warning

This appliance must be

earthed

If the fitted moulded plug is not suitable

for your socket, then the plug should

be cut off and an appropriate plug

fitted.

Destroy the old plug, which is cut off as

a plug with a bared cord could cause a

shock hazard if inserted into a socket

elsewhere in the house.

With the alternative plugs a 13A fuse

must be fitted either in the plug or

adaptor or in the main fuse box. If in

doubt contact a qualified electrician.

��

The moulded plug on this appliance

incorporates a 13A fuse. Should the

fuse need to be replaced an ASTA

approved BS1362 fuse of the same

rating must be used. Do not forget

to refit the fuse cover. In the event of

losing the fuse cover, the plug must

not be used until a replacement fuse

cover has been fitted. Colour of the

replacement fuse cover must be the

same colour as that visible on the

pin face of the plug. Fuse covers are

available from any good electrical

store.

�

��

Important

Fitting a different plug

As the colours of the wires in the

mains lead of this appliance may not

correspond with the coloured markings

identifying the terminals on your plug,

proceed as follows:

1. Connect the green - yellow or

green (earth) wire to the terminal

in the plug marked ‘E’ or with the

symbol

or coloured green

and yellow or green.

2. Connect the blue (neutral) wire to

the terminal in the plug marked ‘N’

or coloured black.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Water inlet hose connection

Make sure your plumbing is suitable to

install your new dishwasher. If in doubt

contact a qualified plumber.

Drain Hose Connection

Fit the drainage hose of your machine

to the drainage pipe without bending.

Secure your hose firmly to the waste

pipe to avoid it coming off during the

washing process.

The appliance must be connected

to the water mains using the new

hose set supplied with your new

dishwasher. Old hose sets must not

be re-used.

The waste pipe must only be

connected into the foul drains and not

surface water drainage system.

The water pressure coming from

the water mains supply must be a

minimum of 0.3 and a maximum of 10

bars.

The hose should be placed between

50 cm and 110 cm from the floor level

and must not be extended otherwise

the machine may not empty the waste

water.

Connect the straight end to your water

mains supply

Ensure plastic filter

and black rubber seal is in place.

Please turn on the tap and check for

leakages after connecting the hose.

We recommend the tap is turned off

when the machine is not being used.

If you only have one cold water

feed (For example for your washing

machine) don’t worry, a Y adaptor

will provide you with the additional

cold water feed you need for your

dishwasher. Y adaptor is available from

most DIY stores.

��

�

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

tap and a drain.

Installation of dishwasher

Remove all packaging before

positioning the machine.

When inserting the machine, ensure

that the water inlet and drain hoses are

not linked or squashed.

See the following diagram. Ensure

there is a clearance each side of the

machine to allow slight side ways

movement for servicing.

Care must be taken to ensure that

the appliance does not stand on the

electrical supply cable.

Note:

Good levelling is essential for correct

closure and sealing of the door.

If there is already enough space, you

don’t need to remove the worktop to

install it under the counter.

Make sure your dishwasher is perfectly

level using the adjustable feet.

Position the machine next to a water

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

When the appliance

is correctly levelled,

the door will not catch

on the inner liner

on either side of the

cabinet.

If the door does

not close correctly,

loosen or tighten

the adjustable feet,

until the machine is

perfectly level.

��

�

5 How to use

Water hardness & regeneration settings

The dishwasher requires lime free water. Hard water leaves watermarks on your

dishes. Your dishwasher has a special water softening system to remove the

hardness of the tap water. Setting this system correctly will increase the washing

effectiveness.

To find out the hardness level of water in your area, contact your local Water

Board or Determine water hardness level by the help of test strip provided.

If you move to a different location, the level of water hardness will possibly

be different. It is essential to reset the water hardness in order to obtain

optimum washing efficiency.

��

�

��

�

��

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

To Adjust the Water Hardness;

1. Move the programme selection key to position 1 when the machine is turned

off.

2. Press Start/Pause/Cancel button.

3. Press On/Off button while keeping the Start/Pause/Cancel button pressed

to turn the machine on. Do not release the Start/Pause/Cancel button until

“Water Hardness Level” set appears on the indicator of the machine (See. Water

Hardness Level Adjustment Table).

4. The default “Water Hardness Level” will remain lit on the panel of the machine

for about 5 seconds. Release the Start/Pause/Cancel button after the default

“Water Hardness Level” appears.

5. To adjust the new Water Hardness Level, move the programme selection key

to the position that is suitable for your water supply. (See. Water Hardness Level

Adjustment Table)

**Programme selection key rotates in 5 steps regardless of the number of the

programme contained on the machine.

6. Press “Start/Pause/Cancel” key once to store the level you have selected.

7. Press the On/Off key to turn off your machine.

Water Hardness Level Adjustment Table

If the hardness level of the water that you use is above 80 °dF (French standard

for water hardness) or if you are using well water, then it is recommended to use

filter and water purification devices.

If the hardness level of the water that you use is below 9°dF (French standard

for water hardness), there is no need to use salt in your dishwasher. If this is the

case, “No Salt Warning Indicator” (if any) illuminates continuously on the panel of

your machine.

If the water hardness adjustment is set to level 1, the “No salt warning indicator”

will illuminate continuously although it is not necessary to use salt. If you use salt

under this condition, salt will not be consumed and the lamp will not illuminate.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Adding Dishwasher Salt

Only use special pelletized dishwasher

salt in your machine to soften the hard

water. Never use other types of salts

including table salt, animal feeding salt,

sea salt, culinary salt. These types of

salt do not dissolve in water easily and

will damage your appliance beyond

repair.

Detergent use

Any brand of powder, gel and tablet

detergents that have been designed for

household dishwashers, may be used.

Keep detergents in a cool and dry

place and out of the reach of children.

Detergent must be added to the

container before each use.

When you run the dishwasher, the

Water softener will be full of water.

Therefore, adding softening salt

should always be done immediately

before you start the dishwasher.

Detergent overdose may cause

scratches on your dishes and there

may be traces of detergent left in your

machine.

Three types of detergent are available

•

Phosphate and containing

chlorine.

��

�

•

Phosphate containing no chlorine

Neither containing phosphate nor

chlorine

Caution : Only fill with salt just before

starting one of the complete washing

programmes to prevent any grains of

salt causing corrosion. Ensure 1 Litre

of water has been added. You can put

approximately 2 kg softening salt in the

Water softener.

New compact powders are generally

phosphate-free. As phosphates have

water softening properties, we suggest

you add salt to the salt container even

if the hardness of your water is as low

as a 6 clarke degrees.

To fill the container with softening

salt, remove the lower rack first and

unscrew the cap of the water softener

turning anti clockwise.

In hard water areas if a phosphate free

detergent is used, white marks on the

dishes and glasses may be observed.

It may be prevented by increasing the

amount of detergent.

Using the funnel provided will make

filling easier.

Detergents without chlorine have less

bleaching effect. Coloured stains may

not be completely removed. This may

After you fill the container, screw cap

tightly back into place turning clockwise be prevented by increasing the amount

until you hear a click sound.

of detergent, using a programme with

a higher wash temperature or using a

detergent with chlorine.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Warning!

Two-in-one and three-in-one

detergents

dishwasher. Always place the

tablets in the detergent dispenser

of the detergent holder.

You will obtain the best results from

your dishwasher if you use separate

detergent, rinse aid and water-

softening salt.

Using three-in-one detergent,

softening salt and rinse aid.

•

These detergents will not give you

the same drying performance that

you can obtain by using separate

detergent, salt and rinse aid. To

increase the drying performance:

Put your appliance’s rinse aid

setting at “1” and apply rinse aid.

When the rinse aid is used up,

add more rinse aid to the rinse aid

dispenser.

If you use combined detergents

with a rinse aid setting higher

than 1, hand contact may leave

rainbow-coloured water stains on

the washed items and inside the

machine.

Detergent manufacturers also produce

combined detergents known as ‘two-in-

one’ and ‘three-in-one’.

Three-in-one: These products contain

detergent, rinse aid and water-

softening salt.

Two-in-one: These products contain

detergent and either rinse aid or water-

softening salt.

In general, you will obtain satisfactory

results from combined detergents only

under specific usage conditions. These

detergents contain predetermined

amounts of rinse aid and/or softening

salt. This means that you cannot adjust

the amount of water-softening salt

and rinse aid required to suit the water

hardness level in your home.

•

If you use combined detergents

without adding salt, lime scale may

form especially on glasses. To

avoid lime scale formation:

Put your appliance’s water

softener setting at “1” and add salt.

When the salt is used up, add

more salt to the water softener.

You should bear the following points in

mind when using such detergents:

Using two-in-one detergent:

Be sure to check the specifications detergent and softening salt

•

of the product you are using and

whether it is a combined product

or not.

Follow the instructions on the

packet when using these products.

The use of these products at the

correct appliance settings will

ensure economical use of salt and/

or rinse aid.

•

These detergents do not contain

rinse aid so you need to use the

rinse aid setting as described

in the manual, making sure that

there is rinse aid in the rinse

aid dispenser with every wash

and that you refill the rinse aid

dispenser with rinse aid every time

it is empty.

•

If the detergent is in tablet form,

never place these in the internal

section or cutlery basket of the

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Using two-in-one detergent and

rinse aid

hardness shown in the manual.

Put the rinse aid setting at the

correct level.

•

These detergents will not give you

the same drying performance that

you can obtain by using separate

detergent, salt and rinse aid. To

increase the drying performance:

Put your appliance’s rinse aid

setting at “1” and apply rinse aid.

When the rinse aid is used up,

add more rinse aid to the rinse aid

dispenser.

If you use combined detergents

with a rinse aid setting higher

than 1, hand contact may leave

rainbow-coloured water stains on

the washed items and inside the

machine.

•

These detergents do not contain

softening salt so you need to use

the softening setting as described

in the manual, making sure that

there is salt in the water softener

with every wash and that you refill

the water softener with salt every

time it is empty.

Filling detergent dispenser

If the dishwasher is considerably full

and the dishes are relatively dirty, fill

the main container (A) up to 25cm³

level. If the dishwasher is not quite full

and the dishes are only slightly soiled,

fill the main container (A) only up to

15cm³ level.

If your dishes are kept unwashed for

a long time and the food particles are

stuck on the dishes also fill the small

container (B) up to 5cm³. Depending

on the degree of soiling and the

water hardness in your area it may be

necessary to add more detergent.

Important warning

Should you encounter a problem that

has previously never occured after you

start using these detergents, contact

the detergent manufacturer directly.

You will find contact details on the

packet.

Powder and gel detergents are poured

into the dispenser.

If you stop using this kind of

detergent:

•

Ensure that the salt and rinse aid

dispensers are full.

If you are using tablet detergent read

the manufacturer’s recommendations

on the packaging in order to determine

where the tablets should be placed

inside the dishwasher (detergent

dispenser, cutlery basket, etc.)

•

Put the water hardness setting at

the highest level and run a wash

cycle with the appliance empty.

After washing while empty, return

the water hardness setting to the

correct level for your mains water

•

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

After you put in the detergent, shut the

container lid (D) and ensure you hear

the clicking sound.

During the wash programme the

detergent will dispense automatically

and the lid (D) will remain open when

the programme finishes.

regulator (C).

The dispenser regulator (C) may be set

between levels 1 and 6 (6 being the

maximum amount of rinse aid usage).

Your machine is pre-set at the factory

to level 4.

According to the finish and drying

results obtained, adjust the dose of

rinse aid by means of the six position

selector. (Position 1: minimum dose,

Position 6: maximum dose.) Gradually

increase the dose if there are drops of

water or lime spots on the dishes after

washing. Reduce it if there are sticky

whitish streaks on the dishes.

Do not use detergent when using the

pre-wash programme.

Detergent residues

Regular use of low temperature

washes and/or short duration

programmes can lead to undissolved

detergent residue build up. We

recommend to carry out a service wash

at the highest temperature possible

every 3 - 4 months with the dishwasher

empty and without using detergent. It

is not recommended to carry it out with

auto programme.

Filling the rinse aid dispenser

Open the rinse aid dispenser lid by

pressing the button as shown in the

diagram.

Fill up with rinse aid until the container

is full to level of ’max’ mark .

Put the lid (E) on and ensure you hear

the clicking sound.

Rinse aid

Use only rinse aid intended for

household dishwashers.

Remember to CLOSE the lid after

every refill.

Make sure you clean any rinse aid that

you might have spilled.

The rinse aid is specially formulated

to be used in the dishwashers for the

prevention of watermarks and scale on

dishes and to increase the efficiency

of the washing and drying processes.

Therefore, make sure that

��

there is adequate amount of rinse

aid in the rinse aid dispenser of your

machine.

��

You can adjust the amount of rinse

aid used during the wash programme

by turning the rinse aid dispenser

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Loading the dishwasher

Loading the dishwasher correctly will

increase the washing, drying and

energy performance of your machine.

Examine the information given in this

section and the information stated

in the Programme chart and quick

reference card given with the manual.

Remove any large scraps of food

from the dishes before placing in the

dishwasher to avoid clogging the filters.

There are three separate baskets, in

which you can put your dishes.

Place large or heavily soiled items in

the lower basket, and small, light or

delicate articles in the upper basket.

Put forks, small and medium size

knives and spoons in the cutlery

basket.

��

�

Place tall, narrow items in the middle of

the racks.

�

Long-stemmed glasses should lean

against the basket, the racks, or the

supports not against the dishes.

The shelves on the rack are made

height adjustable to accommodate tall

items.

When loading your dishwasher please

ensure tall glasses (and/or wine

glasses) rest against the sides of the

upper basket. Do not allow tall glasses

to rest against each other since they

may be damaged during washing if not

properly supported.

Always arrange saucepans, cups and

glasses etc. upside down.

You can fold the racks in the upper

basket when you need more space for

larger items.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Folding plate support rods

There are four separate “folding plate

support rods” in the lower basket of

your dishwasher designed to allow

you more space to accommodate

saucepans and large bowls in the

lower basket. You can either fold each

section (1,2,3,4) individually or, all at

once, to create a large empty space.

Simply press the handgrips (A) and

fold them down”

Movable Cutlery Basket

Designed to allow free placement of

the dishes according to their size, the

movable cutlery basket can slide over

the tines to the left (A) and right (B)

side.

�

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Folding Tines

There are “folding tines” in the upper

rack to allow you more space to

accommodate glasses or cups. To

adjust the flexible tines, gently press

the handgrip and lay the tines down

toward the center of the rack. Pull tines

up to fold them up again.

�

Upper basket with variable

height setting

The upper basket is equipped with a

lifting mechanism which enables you

to change the height of the basket

without having to remove it from the

dishwasher, even if it is fully loaded.

The height of the upper basket was

set to its lowest position at the factory.

To lift the upper basket to the “high”

(A) position, hold it on one side and

carefully pull it upwards. To lift the

opposite side of the basket, hold it and

pull it upwards in the same manner (A).

�

To lower the upper rack, hold and

press in the rack lever on one side

and carefully lower the rack without

releasing the lever (B). Repeat the

procedure with the lever on the

opposite side of the basket. Make sure

that both levers catch at the same

height.

�

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Operating the dishwasher

•

Turn the water tap on. Open the

door of the machine.

Check that the upper and lower

arms can rotate freely.

door, as steam and water will escape.

Then after putting in the item, close

the door. The dishwasher will resume

operation.

•

Add the detergent

Close the door of the machine

Push in the on/off button and

check that the programme

indicator lights come on.

Hot Air Drying

Hot Air Drying ensures your dishes are

dried efficiently.

•

Check the salt and rinse aid level

indicator lights before you start the

machine. If necessary add salt and

rinse aid.

•

Select the required programme by

referring to the programme chart.

Choose the desired programme

Press start / stop button and check

that the start / stop indicator light

comes on.

Unloading dishwasher

Dishes should be allowed to cool for

about 15 - 30 minutes after the end of

the programme.

! Do not open the dishwasher door

whilst the appliance is in operation.

However, in case the door is opened

while the machine is working, then

a safety mechanism ensures the

machine immediately stops. Water may

be very hot, so be careful.

You will improve drying results by

leaving the dishwasher door ajar for

at least 15-30 minutes as soon as the

programme finishes.

! Care must be taken if opening the

door, as steam and water will escape.

! Care must be taken when opening

the door, as steam will escape.

•

Press the on/off button after the

programme is completed. The

indicator lights will go off.

Unload the baskets - we

First unload the lower, then the upper

rack. This prevents drops of water from

falling onto the full lower basket when

the dishes in the upper basket are

being removed.

•

recommend to turn off the water

tap when not in use

! Just after the dishwasher has started

the selected programme, if you find

that you want to put in another item to

be washed, open the door carefully.

Care must be taken if opening the

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

7 How to clean your machine

Cleaning your machine at regular

intervals ensures longer product life

and reduces the risk of recurring

problems. Clean spray arms and in

particular filters at least once a week

! Always unplug the appliance and turn

off the water supply before cleaning.

��

To clean the door seal, use a neutral

detergent and a damp cloth. To clean

the control panel, use only slightly

damp cloth.

��

! Do not use abrasive detergents.

If the appliance is not going to be used

for a long period of time, switch off,

turn off the water clean and leave the

door ajar.

How to clean the filters and spray

arms filters

For the efficient operation of your

dishwasher, check the filters and the

spray arms regularly.

There are three different filters in your

machine

Main filter

Coarse filter

Micro filter

To remove the coarse and micro

filter assembly to clean, turn it anti

clockwise as far as it goes and lift it up.

Then press the two tongues inwards

and pull out the coarse filter.

Pull the main filter off.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

Clean all three filters under running tap

water with a brush.

Upper spray arm

Turn the nut anti clockwise and remove

both the nut and the spray arm.

Reinsert the main filter in its place.

Flush away food particles under

running water.

Put the spray arm back on and screw

on the nut turning clockwise until a

clicking sound is heard.

Place the coarse filter into the micro

filter. Ensure the marks align properly.

Turn the coarse filter clockwise until

you hear a clicking sound.

Lower spray arm

It is important that you fit the filters

correctly.

Remove the spray arm from its slot

by releasing the catches and pulling it

upwards.

Caution: the dishwasher must not

be used without filters.

Flush away the food particles under

running water.

Reinsert the spray arm back into its

original position.

Incorrect repositioning of the filters

will produce poor washing results.

Cleaning of the filters is vital to

ensure correct operation of the

machine.

_{Download from Www.Somanuals.com.}G_AlB_{l Manuals Search And Download.}

8 Before calling service / Trouble shooting

Before calling service check the following & Trouble shooting guide supplied on

the following page.

�

��

�

��

TROUBLE SHOOTING GUIDE

SYMPTOMS

POSSIBLE CAUSES

SOLUTIONS

Insufficient amount of

detergent

Increase the amount of detergent, especially when

washing full loads, or in hard water.

Increase water softener dosage. Use additional

detergent, increase rinse agent dosage.

Hard water.

Check the nozzle holes in the spray arms. They may

be blocked with a soil particle. Check and clean them

periodically.

Spray arms need cleaning

Spotting /

filming / poor

cleaning results

Follow instructions for use for proper loading

procedures. Place dishes so water spray reaches all

soiled surfaces. Do not overcrowd the baskets since

this will block the water spray.

Improper loading.

Insufficient water fill.

Check mains water pressure

Remove any accumulated or deposited foods. Check

and clean them periodically.

Filter system needs cleaning.

Oversudsing - Prewashing withRinse items thoroughly before putting them in the

a liquid dishwashing detergent.dishwasher to remove dishwashing detergent.

Check to be sure water action is not blocked by

Water not reaching surfaces, dishes. Check filter system for accumulated or

dishwasher overcrowded.

deposited food or detergent. Load dishwasher

correctly. Keep filter system clean.

Small particles

(food or

Insufficient water fill.

Check mains water pressure

detergent) left

on items

Use powder detergent within one to two months after

purchase. Open one box at a time. Always close

pouring spout after each use. Store in a cool, dry

place.

Powder detergent stored

too long or under adverse

conditions.

Rinse aid supply depleted.

Add rinse aid to the dispenser.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remove spots with silver polish. Rewash. Wash soon

after use, or pre-wash items if they will not be washed

right away. Do not overload cutlery basket. Avoid

spilling or pouring detergent directly on flatware. Make

sure dispenser cup is properly closed.

Prolonged contact with salty

or highly acidic foods or

with undissolved or highly

concentrated detergent.

Pitting of

stainless steel

items

Load so that all items are properly tilted for good

drainage. Avoid nesting of dishes and/or silverware.

Improper loading.

Dishes not dry

Rinse aid supply depleted.

Add liquid rinse aid .

The condition may not always be preventable. To

minimize the possibility of etching, use minimum

amount of detergent.

A water or chemical reaction

with some glassware. Usually

caused by some combination

of soft or softened water and

alkaline washing solutions

reacting with the glassware.

Can be accelerated by poor

rinsing, overloading and

Scratches on

glassware

Use of the appropriate programme.

Use of a rinse aid may also help.

excessive temperature.

If using powder detergent,

there may be dampness in the

dispenser.

Make sure dispenser is dry before adding powder

detergent. Start dishwasher immediately.

If using gel detergent, the

detergent may be left in

dispenser too long before

using.

Start dishwasher soon after adding gel detergent. Do

not allow detergent to dry out in dispenser.

Detergent

cakes in

detergent

dispenser.

Do not overfill. Cover should close tightly. Check

cover for fit.

Faulty cover.

Improper loading.

Do not place large items in front of dispenser.

Use detergent within one to two months of purchase.

To assure freshness, buy detergent as needed and

no more than one or two at a time. Store in a cool, dry

place.

Old detergent.

Chipping and

breakage of

dishes/glasses

Load with care following the instructions for use.

Place glassware so it does not touch the other dishes.

Remove from dishwasher carefully.

Improper loading.

Use the pre-wash cycle at least once a day until a

load accumulates, or hand rinse dishes before loading

dishwasher.

Dishes washed only every two

or three days.

Odour in

dishwasher

A dirty filter system may

contribute to a bad odour.

Clean filter system.

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Loss of frozen food in freezers

or fridge/freezers. (Food loss

insurance is often included within

your household contents insurance

policy, or may be available

Guarantee for Refrigeration,

Cooking Appliances, Washing

Machines & Dishwashers.

separately from your retailer).

Important notes.

Your new Beko product is guaranteed

against the cost of breakdown repairs

for one year from the date of the

original purchase.

•

Your Beko product is designed and

built for domestic household use

only.

•

The guarantee will be void if the

product is installed or used in

commercial or non-residential

domestic household premises.

The product must be correctly

installed, located and operated in

accordance with the instructions

contained in the User Instructions

Booklet provided.

What is covered?

•

Repairs necessary as a result

of faulty materials, defective

components or manufacturing

defect.

•

The cost of functional replacement

parts, but excluding consumable

items.

The labour costs of a Beko

approved repairer to carry out the

repair.

Professional installation

by a qualified Electrical

Domestic Appliance Installer is

recommended for all Washing

Machines, Dishwashers and

Electric Cookers

What is not covered?

•

Transit, delivery or accidental

damage or misuse and abuse.

Cabinet or appearance parts,

including knobs, flaps, handles or

container lids.

•

Gas Cookers must only be

installed by a Gas safe (or BORD

GAIS) registered Gas Installer.

The guarantee is given only within

the boundaries of the United

Kingdom and the Republic of

Ireland.

•

Accessories or consumable items

including but not limited to, ice

trays, scrapers, cutlery baskets,

filters and light bulbs.

Repairs required as a result of

unauthorised repair or inexpert

installation that fails to meet the

requirements contained in the user

instruction book.

•

The guarantee is applicable

only to new products and is not

transferable if the product is

resold.

•

Beko disclaims any liability for

incidental or consequential

damages.

The guarantee does not in anyway

diminish your statutory or legal

rights.

•

Repairs to products used on

commercial or non-residential

household premises.

Download from Www.Somanuals.com. All Manuals Search And Download.

•

The product guarantee does not

cover damages to plates,glass

ware, cutlery, crockery and also

damage to the product itself as

a result of using these “Three-in-

one”, “Two-in-one” detergents.

Before requesting service please

check the trouble-shooting guide

in the Operating Instructions as a

charge may be levied where no fault

is found even though your product

may still be under guarantee.

Please keep your purchase receipt

or other proof of purchase in a

safe place; you will need to have it

should the product require attention

under guarantee.

Service once the manufacturers

guarantee has expired.

If you have purchased an extended

guarantee please refer to the

instructions contained within the

extended guarantee agreement

document. Otherwise please call the

appropriate number above where

service can be obtained at a charge.

You should also complete the details

below; it will help us assist you when

requesting service. (The model

number is printed on the Instruction

Booklet and the serial number is

printed on the Rating Label affixed to

the appliance)

Should you experience any difficulty

in obtaining service please contact the

Beko Customer Help-Line.

Model No:

Tel: 0845 6004911

Serial No:

e-mail: [email protected]

Retailer:

Date of purchase:

Beko plc, Beko House, Caxton Way,

Watford, Herts, WD18 8UF

www.beko.co.uk

For service under guarantee simply

telephone the appropriate number

below

UK Mainland & Northern Ireland

Fridges & Freezers

Electric Cookers

0845 6004903

0845 6004902

Gas&Dual Fuel Cookers 0845 6004905

Washing Machines

& Dishwashers

0845 6004906

Republic of Ireland

All Refrigeration, All Cookers

01 862 3411

Washing Machines & Dishwashers

17 9426 0100 Revision: AA-04/12

Download from Www.Somanuals.com. All Manuals Search And Download.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

��

3Com Network Router 3CRWDR200A 75 User Manual
3M Tablet Accessory 10700 User Manual
A4 Tech Mouse Wireless 1 Wheel Mouse User Manual
Acnodes Computer Hardware FES7611 User Manual
ACTiSYS Network Card ACT IR210L User Manual
ADC Network Card UltraWAVE CDMA Pico BS Plus User Manual
Akai Clock Radio AR215P User Manual
American Audio Stereo Amplifier 4295 User Manual
Atlantis Land Switch A07 ES4704BD User Manual
Behringer Musical Instrument PMH660M PMH880S User Manual