™
REFERENCE MANUAL
©2001 ALESIS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents/Safety Warnings
CONTENTS
Introduction
2
IMPORTANT SAFETY INSTRUCTIONS......................................................3
Safety symbols used in this product
3
5
Instructions de Sécurité Importantes (French)
Information to the User for Class A Digital Device (FCC Part 15, Class A) 7
CE Declaration of Conformity
8
ABOUT THE M1 ACTIVE MK2 ...............................................................9
Unpacking and Inspection
Inside your new speakers
About Nearfield monitoring
9
10
15
SPEAKER INSTALLATION.................................................................... 17
Avoiding reflections in the studio
Stereo nearfield placement of the M1 Active Mk2
Connections
17
20
26
28
Setting the Input Level control
SURROUND SOUND ............................................................................ 31
About surround sound
31
32
33
34
Center speakers in music mixes
Placement of the center M1 Active Mk2 speaker in the studio
Placement of rear surrounds
Mixing for discrete six channel reproduction: matched vs. specialized speakers
37
TROUBLESHOOTING ...........................................................................39
Troubleshooting Index
Maintenance
39
40
SPECIFICATIONS ................................................................................42
Enclosure
42
42
43
43
43
43
Transducers
Crossover section
Amplifier Section
Acoustic Section
General
INDEX.............................................................................................. 44
ALESIS LIMITED WARRANTY..............................................................45
M1 Active Mk2 Reference Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents/Safety Warnings
INTRODUCTION
Thank you for purchasing the Alesis M1 Active Mk2 Biamplified Reference
Monitors. To take full advantage of the M1 Active Mk2’s operation, and to
enjoy long and trouble-free use, please read this user’s manual carefully. We
value any comments you may have about this monitor system, this manual,
your Alesis dealer or our factory service. Please take a minute now to fill out
your warranty card and tell us what you think.
HOW TO USE THIS MANUAL
This manual is divided into the following sections describing the various
features of the M1 Active Mk2. Though we recommend you take time to read
through the entire manual once carefully, those having general knowledge
about monitors should use the table of contents to reference specific
functions.
Chapter 1: About the M1 Active Mk2. Engineering specifications and
reasons why nearfield monitors have become so popular.
Chapter 2: Speaker Installation. This chapter explains how to connect the
M1 Active Mk2s to a mixer or other line-level source and discusses proper
speaker placement for stereo operation.
Chapter 3: Surround Sound. If you are using the M1 Active Mk2 speakers in
a multichannel surround sound setup, you’ll find helpful setup and operation
information here.
Chapter 4: Troubleshooting. This chapter contains troubleshooting tips and
service information should problems occur.
✪
When something important appears in the manual, an icon (like the
one on the left) will appear in the left margin. This symbol indicates
that this information is vital when operating the M1 Active Mk2s.
2
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents/Safety Warnings
IMPORITNASNTTRUSCATFIOENTYS
SAFETY SYMBOLS USED IN THIS PRODUCT
This symbol alerts the user that there are important operating and
maintenance instructions in the literature accompanying this unit.
PLEASE FOLLOW THESE PRECAUTIONS WHEN USING THIS
PRODUCT:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a damp cloth. Do not spray any liquid cleaner onto the
speakers or rear panel, as this may damage the speakers, controls or cause
a dangerous condition.
7. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. When the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
M1 Active Mk2 Reference Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents/Safety Warnings
10. Protect the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Use only attachments or accessories specified by the manufacturer.
12. Use only with a cart, stand, bracket, rack, or table designed for use with
professional audio or music equipment. In any installation, make sure
that injury or damage will not result from cables pulling on the apparatus
and its mounting. If a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as when
the power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. This product may be capable of producing sound levels that could cause
permanent hearing loss. Do not operate for a long period of time at a high
volume level or at a level that is uncomfortable. If you experience any
hearing loss or ringing in the ears, you should consult an audiologist.
4
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents/Safety Warnings
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES (FRENCH)
SYMBOLES UTILISÉS DANS CE PRODUIT
Ce symbole alèrte l’utilisateur qu’il existe des instructions de fonctionnement et
de maintenance dans la documentation jointe avec ce produit.
Ce symbole avertit l’utilisateur de la présence d’une tension non isolée à l’intérieur de
l’appareil pouvant engendrer des chocs électriques.
VEUILLEZ SUIVRE CES PRÉCAUTIONS LORS DE
L’UTILISATION DE L’APPAREIL:
1. Lisez ces instructions.
2. Gardez ces instructions.
3. Tenez compte de tous les avertissements.
4. Suivez toutes les instructions.
5. N’utilisez pas cet allareil à proximité de l’eau.
6. Ne nettoyez qu’avec un chiffon humide. Ne pas vaporiser de liquide nettoyant sur l’appareil,
cela pourrait abîmer les contrôles de la face avant ou engendrer des conditions dangeureuses.
7. Installez selon les recommandations du constructeur.
8. Ne pas installer à proximilé de sources de chaleur comme radiateurs, cuisinière ou autre
appareils (don’t les amplificateurs) produisant de la chaleur.
9. Ne pas enlever la prise de terre du cordon secteur. Une prise murale avec terre deux broches
et une troisièrme reliée à la terre. Cette dernière est présente pour votre sécurité. Si le cordon
secteur ne rentre pas dans la prise de courant, demandez à un électricien qualifié de
remplacer la prise.
10. Evitez de marcher sur le cordon secteur ou de le pincer, en particulier au niveau de la prise,
et aux endroits où il sor de l’appareil.
11. N’utilisez que des accessoires spécifiés par le constructeur.
12. N’utilisez qu’avec un stand, rack ou table conçus pour l’utilisation d’audio professionnel ou
instruments de musique. Dans toute installation, veillez de ne rien endommager à cause de
câbles qui tirent sur des appareils et leur support.
13. Débranchez l’appareil lors d’un orage ou lorsqu’il n’est pas utilisé pendant longtemps.
14. Faites réparer par un personnel qualifié. Une réparation est nécessaire lorsque l’appareil a
été endommagé de quelque sorte que ce soit, par exemple losrque le cordon secteur ou la
prise sont endommagés, si du liquide a coulé ou des objets se sont introduits dans l’appareil,
si celui-ci a été exposé à la pluie ou à l’humidité, ne fonctionne pas normalement ou est
tombé.
15. Cet appareil produit de la chaleur en fonctionnement normal. Si cet appareil est utilisé dans
un rack, veillez à sa bonne ventilation lors de son utilisation. Ne pas faire fonctionner dans
un rack fermé. S’il y a d’autres appareils dans le rack générant beaucoup de chaleur,éloignez
les. Ne pas intercaler cetappareil entre deux appareils produisant beaucoup de chaleur.
16. Ce produit, utilisé avec un amplificateur et un casqueou des enceintes, est capable de
produite des niveaux sonores pouvant engendrer une perte permanente de l’ouïe. Ne
l’utilisez pas pendant longtemps à un niveau sonore élevé ou à un niveau non confortable. Si
vous remarquez une perte de l’ouïe ou un bourdonnement dans les oreilles, consultez un
spécialiste.
M1 Active Mk2 Reference Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents/Safety Warnings
BEIM BENUTZEN DIESES PRODUKTES BEACHTEN SIE
BITTE DIE FOLGENDEN SICHERHEITSHINWEISE: (GERMAN)
1. Lesen Sie die Hinweise.
2. Halten Sie sich an die Anleitung.
3. Beachten Sie alle Warnungen.
4. Beachten Sie alle Hinweise.
5. Bringen Sie das Gerät nie mit Wasser in Berührung.
6. Verwenden Sie zur Reinigung nur ein weiches Tuch. Sprühen Sie keine flüssiger Reinigerauf
die Oberfläche, dies könnte zur Beschädigung der Vorderseite führen und auch weitere
Schäden verursachen.
7. Halten Sie sich beim Aufbau des Gerätes an die Angaben des Herstellers.
8. Stellen Sie das Gerät nich in der Nähe von Heizkörpern, Heizungsklappen oder anderen
Wärmequellen (einschließlich Verstärkern) auf.
9. Verlegen Sie das Netzkabel des Gerätes niemals so, daß man darüber stolpern kann oder daß
es gequetscht wird.
10. Benutzen Sie nur das vom Hersteller empfohlene Zubehör.
11. Verwenden Sie ausschließlich Wagen, Ständer, Racks oder Tische, die speziell für
professionelle Audio- und Musikinstrumente geeignetsind. Achten Sie immer darauf, daß
die jeweiligen Geräte sicher installiert sind, um Schäden und Verletzungen zu vermeiden.
Wenn Sie einen Rollwagen benutzen, achten Sie darauf, das dieser nicht umkippt, um
Verletzungen auszuschließen.
12. Ziehen Sie während eines Gewitters oder wenn Sie das Gerät über einen längeren Zeitraum
nicht benutzen den Netzstecher aus der Steckdose.
13. Die Wartung sollte nur durch qualifiziertes Fachpersonal erfolgen. Die Wartung wird
notwendig, wenn das Gerät beschädigt wurde oder aber das Stromkabel oder der Stecker,
Gegenstände oder Flüssigkeit in das Gerät gelangt sind, das Gerät dem Regen oder
Feuchtigkeit ausgesetzt war und deshalbnicht mehr normal arbeitet oder heruntergefallen
ist.
14. Bei normalem Betrieb des Gerätes kommt es zu Wärmeentwicklungen. Wenn Sie das Gerät
in einem Rack eingebaut haben, sollte während des Betriebes die Zufuhr von Kühlluft stets
gewährleitstet sein. Arbeiten Sie nie beigeschlossenem Rack. Bei mehreren Rackgeräten
sollten diese mit einem geringen abstand voneinander eingebaut werden. Stapeln Sie dieses
Gerät nicht zwischen Geräten mit hoher Wärmeentwicklung.
15. Dieses Produkt kann in Verbindung mit einem Verstärker und Kopfhörern oder
Lautsprechern Lautstärkepegel erzeugen, die anhaltende Gehörschäden verursachen.
Betreiben Sie es nicht über längere Zeit mit hoher Lautstärke oder einem Pegel, der Ihnen
unangenehm is. Wenn Sie ein Nachlassen des Gehörs oder ein Klingeln in den Ohren
feststellen, sollten Sie einen Ohrenarzt aufsuchen.
6
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents/Safety Warnings
INFORMATION TO THE USER FOR CLASS A DIGITAL
DEVICE (FCC PART 15, CLASS A)
This equipment has been tested and found to comply with the limits for a
class A digital device pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause interference to radio
communications. Operation of this equipment in a residential area is likely to
cause interference in which case the user will be required to correct the
interference at his own expense.
The user is cautioned that changes and modifications made to the equipment
without the approval of manufacturer could void the user’s authority to
operate this equipment.
Use only shielded and grounded cables with this equipment to ensure
compliance with FCC Rules.
INDUSTRY CANADA (DIGITAL APPARATUS)
INTERFERENCE-CAUSING EQUIPMENT STANDARD
ICES-003 ISSUE 2
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
M1 Active Mk2 Reference Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents/Safety Warnings
CE DECLARATION OF CONFORMITY
This product conforms to current applicable CE standards for safety. For a
detailed description of the standards used, please see the web site Alesis.com.
8
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About the M1 Active Mk2
CHAPTER 1
ABOUT THE M1 ACTIVE MK2
UNPACKING AND INSPECTION
Your M1 Active Mk2 Biamplified Reference Monitors were packed carefully
at the factory, and the shipping carton was designed to protect the speakers
during shipping. Please retain this container in the highly unlikely event that
you need to return the speakers for servicing.
The shipping carton should contain the following items:
• This instruction manual
• M1 Actives with the same serial numbers as shown on the shipping
cartons
• Two AC power cords (NEMA to CEE type)
• Alesis warranty card
• Two pieces of adhesive-backed non-skid foam
✪
It is important to register your purchase; if you have not already
filled out your warranty card and mailed it back to Alesis, please
take the time to do so now.
The M1 Active Mk2s are designed as mirror-imaged pairs. If you have
received a pair where the tweeters are both on the same side, contact your
dealer immediately.
M1 Active Mk2 Reference Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
About the M1 Active Mk2
INSIDE YOUR NEW SPEAKERS
✪
If you’re in a hurry to get started, skip ahead to Chapter 2,
“Speaker Installation”, for connection and placement tips.
ABOUT POWERED MONITORS
The M1 Active Mk2s combine a speaker and amplifiers in the same compact
cabinet. Powered monitors are growing in popularity over the traditional
separate amplifier and speakers for a number of reasons, convenience and
ease of hookup being only one of them. You can connect a powered speaker
directly to any line-level source (normally, the control room output of a
mixer) simply by connecting a patch cord.
Another benefit is improved sound quality. With careful design, the speaker,
amplifier and electronic crossover can be optimised for each other. The M1
Active Mk2s are biamplified, meaning that low frequencies and high
frequencies are handled not only by separate speakers (the tweeter and the
woofer), but by separate amplifiers. A pair of M1 Active Mk2s contain a total
of four power amplifiers. Because of the increased efficiency of
biamplification, these are much louder than a single-channel power amplifier
of the same wattage feeding a passive crossover, as in other designs. New
technology makes it possible to make these high-wattage amplifiers small
enough to fit inside the speaker cabinet, with very little weight or size gain.
Since the M1 Active Mk2s are self-powered, DO NOT connect them to
the speaker output of another amplifier (such as a powered mixer or hi-
fi receiver). Connect them only to the line-level outputs of such devices
(+4 dBu nominal, +24 dBu maximum).
10
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About the M1 Active Mk2
TONE
Tonally, every effort has been made to create a powered monitor that is as
linear as possible, representing a flat frequency response from 50Hz to 20KHz
2dB. (see p. 21) Additionally, the use of electronic crossovers within the
critical upper midrange frequencies has reduced phase and time delay
anomalies often associated with passive crossovers. By including discrete
woofer and tweeter amplifiers and application-specific electronic high and
low pass crossover filters in the same enclosure the tonal accuracy of the M1
Active Mk2 will always remain constant.
ABOUT THE DRIVERS
The M1 Active Mk2’s 6.5” woofer cone is made of proprietary non-woven
carbon fiber. This material is 25% lighter than polypropylene with twice the
stiffness for quicker transient response in the low-to-midbass region and
vastly improved midrange intelligibility (over polypropylene at 2000 Hz).
The non-woven carbon fiber cone, along with the closed cell synthetic rubber
surround, are both nearly impervious to ozone, direct sunlight, heat and
humidity. Therefore, after an initial break-in period, the sound should remain
virtually unchanged for the life of the product.
Alesis’ proprietary-design tweeter features a special wave guide baffle to
improve polar response, a silk dome, and low viscosity ferrofluid formulated
specifically to retain the best balance of transient response to power handling.
The shielded tweeter utilizes a vented pole piece with a separate rear
chamber to lower the free air resonance. The low 2000Hz crossover point of
this tweeter produces a very widely dispersed, low-distortion signal within
the critical midrange frequencies. It is these frequencies which are often the
most problematic to get “right” during a mix. The tweeter is designed for an
optimal response for non-fatiguing, long term, high level, nearfield
mixdowns. This design results in a flat, linear mix when played back on home
or car systems from appropriate distances.
MAGNETIC SHIELDING
Your M1 Active Mk2s are at home in recording environments wherein video
is a major component. They are magnetically shielded for use in fairly close
proximity (3” minimum) to a computer monitor or video screen. (Non-
shielded components can make the colors of a screen “smear” or appear out
of focus if the speaker is too close.) Magnetic shielding was designed into
both the woofer and the tweeter from the beginning so that the system
exhibits about low magnetic leakage. Shielding of both the woofer and the
tweeter is accomplished by the use of a second opposing-field-oriented
“bucking” magnet.
M1 Active Mk2 Reference Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
About the M1 Active Mk2
THE M1 ACTIVE MK2 BI-AMPLIFIERS & ELECTRONIC
CROSSOVERS
The M1 Active Mk2 uses a 75W woofer amp and a 25W tweeter amp along
with 4th order high and low pass electronic crossover filters centered at
2000Hz. Electronic crossovers, which separate the frequencies before being
sent to the amplifiers, have fewer phase problems and less power loss than
the traditional passive crossover used after the amplifier. Fourth-order filters
are steep (24 dB per octave), which minimizes the interaction between woofer
and tweeter near the crossover point. Additionally, the high pass (tweeter)
section of this system employs an electronic time alignment circuit. Thus the
“launch” of frequencies from both the woofer and the tweeter will originate
at exactly the same time.
There are several advantages to using built-in amplifiers and active
(electronic) crossovers versus a passive network system, most of which have
been previously enumerated in Vance Dickason’s “Loudspeaker Design
Cookbook”:
• Lower intermodulation distortion due to amplifier operation over a more
narrow bandwidth. Also, clipping caused by low frequency overload is
reduced, being limited to only one driver within a two driver system.
• Increased dynamic range. The M1 Active Mk2’s 75W and 25W amplifiers
in their bi-amp setup will clip at about the same levels as one 200W
amplifier operating into a passive crossover.
• Improved transient response.
• Better amplifier/speaker coupling for woofers.
• Better crossover performance working into a constant impedance load.
• Better subjective sound quality than high level (passive) networks.
• Easier control over driver sensitivity differences.
• Easier manipulation of phase, time delay, resonance, and various kinds of
shaping, contouring and equalization.
• Specifically in the case of the M1 Active Mk2, the wide, mid-frequency
polar response of the tweeter can be utilized down to a low 2000 Hz
thereby mating more cohesively with the 6.5" non-woven carbon fiber
(NWCF) woofer. This low crossover point is only possible through the use
of a steep, electronic fourth-order (24 dB per octave rolloff) high pass filter.
12
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About the M1 Active Mk2
THE M1 ACTIVE MK2 POWER SUPPLY
The M1 Active Mk2 employs a regulated switching power supply. This type
of supply has previously only been available in amplifiers sold at the very
high end of the Pro Audio market.
Most power amp customers are familiar with the large transformer and
output capacitors in high quality amplifiers. These large components are
used to keep the amplifier’s supply rails as close to DC as possible. For
traditional supplies, bigger is better.
But by using Pulse Width Modulation (PWM) and output voltage feedback in
the M1 Active Mk2, we have the equivalent of near-infinite transformer and
output capacitors, but at a fraction of the cost. PWM provides protection
from line voltage surges that would otherwise destroy the amplifier. No
user-replaceable fuse is required because nuisance tripping is eliminated.
And finally, PWM practically eliminates hum because the line frequency (60
Hz) transformer is replaced with a very high frequency (130,000 Hz)
transformer.
The regulated supply rails increase the amplifier dynamic range and reduce
clipping distortion under heavy loading. The compact size of the supply does
not significantly reduce the internal air volume of the speaker cabinet. And
lastly, full power can be maintained even with low or “flat-topped” line
voltages.
Note, however, that this switching supply is NOT a universal voltage
type that may be used with any input voltage in any country simply by
changing the cord. If you wish to use the M1 Active Mk2s in a country
whose line voltage is other than 120 volts AC, they must be internally
modified or used with a step-down transformer.
THE CABINET AND PORT DESIGN
The M1 Active Mk2 cabinet construction employs vinyl composite material
laminated to a .625” MDF (medium density fiberboard) core for the four sides
and the rear. The front panel is 1” thick MDF, to withstand the greater
demands of the drivers mounted on it. The entire cabinet is braced
extensively in random fashion to dissipate intramodal vibration.
M1 Active Mk2 Reference Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
About the M1 Active Mk2
WHY THE TWEETERS ARE OFFSET
The M1 Active Mk2 speakers have been developed as a mirror-imaged pair
with dual front mounted ports and an offset tweeter. In some applications,
an extremely wide dispersion tweeter, such as used in the M1 Active Mk2,
will exhibit response dips if mounted exactly on center. Wave-guide style
tweeters, used in other products, purposely limit dispersion and thus can be
center mounted. But as hi-end audiophile speaker companies have found, a
high quality dome tweeter, offset in the cabinet toward the stereo “image
center” (between the left and right speakers) will have a flatter characteristic
frequency and power response. This (flat power response) more closely
characterizes the way humans hear.
On a horizontal polar response curve of the M1 Active Mk2, with the cabinet
placed vertically, the tweeter response at one meter stays essentially
symmetrical on either side of the cabinet’s centerline. This is because the
angle subtended between the cabinet-centerline-to-tweeter-centerline (.5”),
and the nominal nearfield listening distance (1 meter or 39.375”), is only 1.27
degrees. Thus, acoustically speaking, the offset tweeter design has no
negative effects, only the positive of smoothing the frequency response in the
2KHz-4KHz range.
In the tradition of the Alesis Superport design, which uses the energy from
the back of the speaker to enhance bass performance, the M1 Active Mk2s use
dual, front baffle mounted, long folded ports. The dual ports on the M1
Active Mk2 are also non-symmetrical with relation to their distances from the
woofer. In developing the M1 Active Mk2, Alesis engineers determined that
dual ports, offset to the outside of the stereo image center gave the most
coherent and extended low bass augmentation. The ports are flared on the
front baffle to provide smooth and quiet exit airflow while inside they are cut
with a 45° angle and faced toward the amplifier’s internal heat sink. This
arrangement aids in keeping the internal amps working at a more constant
temperature. At the same time, this 45° angle increases the port’s air entry
efficiency.
14
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About the M1 Active Mk2
ABOUT NEARFIELD MONITORING
In the early days of recording, most recording studios used big monitor
speakers almost exclusively. Unfortunately, they also required high powered
amplifiers and expensive acoustic treatment (often poorly done) of the entire
control room. Still, a well-constructed big monitoring system really was
impressive to listen to, a fact not overlooked by the studio owners who
wanted to impress the record company executives who paid for the big
studio's time. These big systems had big level control knobs, and clients
enjoyed "cranking-up" the volume. Fortunately, recording engineers and
producers eventually learned that this was not the best way to accurately mix
music because it wasn't the way most people listened to their radios, cassettes
and CD players. Also, big monitor systems and the costs for the required
control room acoustic treatments were going through the roof (no pun
intended), particularly beyond the budget limits of smaller project and home
studios which were growing in numbers. A new way of accurate monitoring
was needed: nearfield monitoring.
Nearfield monitors, by their definition, are intended for mounting close to the
listener. The idea here is to improve the direct acoustic path between the
speaker and the listener by making it shorter, thereby giving less opportunity
for the always present indirect (reflected) sounds to get back in and muddle
things up. With nearfield monitoring, the surrounding acoustic environment
becomes a much less significant factor in establishing the monitor system's
sound character.
A good set of small monitors properly placed in a reasonably non-reverberant
room and properly powered will yield surprisingly accurate results at budget
prices. Carried to another studio, the same monitor should also provide
repeatable results. In fact, some recording engineers carry their own speakers
around because they know how they will sound in almost any room. Now,
even the big studios use smaller speakers to augment their big monitoring
systems, and nearfield monitors have become proven tools in the recording
business.
M1 Active Mk2 Reference Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
About the M1 Active Mk2
16
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
CHAPTER 2
SPEAKER INSTALLATION
Like any speaker system, your M1 Active Mk2 speakers will work best when
properly positioned in a suitable acoustic environment. Achieving proper
speaker placement is usually straightforward, but even with nearfield
monitors, speaker placement and the acoustics of the listening room itself are
too often overlooked and can become significant contributors to an inaccurate
and uninspiring monitoring environment.
AVOIDING REFLECTIONS IN THE STUDIO
While nearfield monitors are more forgiving of the surrounding room
acoustics, it is always prudent to optimize the listening environment
whenever possible. First, the user should be aware of the effect that the size
of the listening room can have on low frequency response. In general, the
smaller the room, the stronger the bottom end will be, although placement
within a larger room can also make a difference. This has to do with the way
low-frequency waves travel in closed spaces. If you find your monitor
system to be either light or heavy on the bottom, try moving them around
within your listening room.
You should avoid locating your M1 Active Mk2s near reflective surfaces such
as glass, tile, large open walls or table tops. Still, many rooms used for
recording have these surfaces, so the best way to deal with them is to place
the monitors out in the room away from reflective walls, windows and
sizable objects. Even with these reflective surfaces separated from the
monitoring position, typical mixing situations usually still have the top
surface of the mixing board to deal with.
Unfortunately, the board itself can be a major source of reflections and the
additional acoustic conduction into the board can affect your monitor's
amplitude and phase response. Speaker placement on the console's meter
bridge allows two different acoustic paths between the speakers and the
recording engineer, which results in undesirable comb filtering effects and
poor imaging. The first path is the direct one, and the second is via a
reflection off the mixer main control panel:
M1 Active Mk2 Reference Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
Direct Path
Monitors placed on the console’s meter bridge can directly radiate
back onto the console control panel causing a strong delayed
reflection at the listening position
This kind of speaker placement also couples acoustic energy from the
speaker's cabinet more readily into the console's chassis. Both conditions
should be reduced by placing the speakers on their own stands acoustically
detached from, and slightly behind, the console as shown below. In this
location, the reflective path off the console's control panel is now blocked by
the meter bridge.
Random
Reflections
Moving the monitors to a position behind the meter bridge causes
the bridge to block the offending reflective path
18
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
Careful consideration should also be given to the physical spacing between
the speakers. Alesis recommends that the distance between the speakers for
stereo applications equal the distance between the listener and either speaker.
In other words, the listener and the two speakers are at the three corners of a
triangle having equal- length sides. The illustration below shows this
concept. Note that both speakers are turned in somewhat, so that the prime
listening position is directly in front of each speaker. Applications that
require monitoring by more than one engineer are accommodated by a
smaller rotation of the cabinets. This will widen the prime listening position
somewhat.
Right Monitor
Left Monitor
The speakers and
listener should be at
the three corners of
a triangle having
equal length sides
Prime Listening Position
NOTE: On some mounting surfaces the vinyl finish of the M1 Active
Mk2’s cabinet may cause it to slip too easily. Included with this
reference manual packet are two pieces of adhesive backed non-skid
foam. If necessary, apply the pad to either the bottom (for vertical
placement) or cabinet side nearest the ports (for horizontal placement).
If you plan on using the M1 Active Mk2s in both modes, simply cut the
pad in half and apply to both the bottom and the side nearest the
ports).
M1 Active Mk2 Reference Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
STEREO NEARFIELD PLACEMENT OF THE
M1 ACTIVE MK2
NOTE: We recommend that the M1 Active Mk2 speakers be placed with the
tweeters to the inside, not the outside, of the listening triangle.
The “classic” studio monitor layout used to be that the tweeters be placed to
the outside of a horizontally-oriented speaker. In the past, this configuration
was actually beneficial in time aligning the tweeter with the woofer if the
cabinets were not toed-in toward the listener. However, this configuration is
highly prone to comb filtering effects if the listener’s head is moved from
side-to-side while mixing. This “comb filtering” causes the mid-to-high
frequency tones to get louder, then softer, then louder again as you move
your head from side-to-side, making it very confusing when trying to mix
with precision.
Some people still believe that stereo separation is “improved” with tweeters
to the outside, but this is advice left over from the early days (the sixties) of
stereo recordings when “correct” stereo often meant a complete hard right or
hard left placement of an instrument (or singer). As stereo mixing techniques
changed toward placing the vocalist (for example) in the center, the old
“tweeters-out” orientation would indeed widen the image if one’s head were
kept in the exact center position. But this set-up proves to be very tiring, very
quickly for the recording engineer. And, to others who are listening to the
mix from either side of the engineer, the sound will seem to be coming
primarily from the speaker closest to them.
Fortunately, recording techniques have changed radically since the sixties.
Engineers have learned to how to “place” an instrument or singer within the
mix so that an accurate re-creation of the actual instrument and vocal
positioning (left-to-right and front-to-back) is achieved. In the M1 Active
Mk2, advances in crossover design technologies and improvements in the off-
axis response of tweeter domes and woofer cone materials and profile have
made the requirement for tweeters to be placed to the outside of the cabinet
obsolete. In fact, using a non-toed-in, tweeters-out orientation with a
modern, wide dispersion design like the M1 Active Mk2 will increase the
likelihood of hearing unwanted first reflections and a variety of phase
anomalies in your mix.
20
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
HORIZONTAL PLACEMENT RECOMMENDATION
Traditionally, proper horizontal placement of speaker systems slightly behind
(not on) a meter bridge accomplished two purposes: it allowed both woofer
and tweeter to be at ear level, and many times, it permitted the recording
engineer to see over the speakers and into the studio.
Horizontal placement is a recommended arrangement with the M1 Active
Mk2 because the left and right mirror-imaged pair permits a symmetrical
alignment of drivers and ports. This will be conducive to a balanced mix. See
Figure 2 below.
Proper tweeter orientation is toward the stereo image center (the middle) as
shown. Ports are always faced toward the bottom side of the cabinet. This set-
up will promote a strongly focused center image such as for the vocalist. And
because the (vocal) image width will be narrower than if the speakers are
placed vertically, it will be possible to place the vocalist with great precision
at stage center. In this orientation there will be much less chance of first
reflections from either sidewalls or the console coloring your mix.
M1 Active Mk2 Reference Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
VERTICAL PLACEMENT RECOMMENDATION
Vertical placement of the M1 Active Mk2 as shown in Figure 3 is highly
recommended. This position will simulate the soundfield that will be heard in
most consumers’ homes and (to a great extent) their cars. For this reason,
even if the M1 Active Mk2s are positioned horizontally for all of the mixing,
the vertical position should always be used in the final "playback check"
mode. (See next section)
There are a couple of possible drawbacks to vertical placement of a nearfield
monitor relating mostly to room interaction effects. Vertical placement allows
the M1 Active Mk2s to portray your mix with the widest and deepest
soundstage possible, so many people in the control room have an image of
the “sweet spot”. However, this wide a dispersion pattern in a control room
with walls in too-close proximity to the speakers can add strong reflections to
the sound you hear, muddying your mix. Page 29 shows the control room
placement/ distance recommendations, which should help you determine if
your available recording space would work well with the M1 Active Mk2s set
up vertically.
22
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
PLAYBACK CHECK MODE (VERTICAL MID-FIELD)
After you’ve got your mix just right it’s always good practice to perform a
“playback check” by standing the M1 Active Mk2s vertically and making the
listening triangle larger. The purpose of the playback check is to simulate
what your masterpiece will sound like in a “typical” home listening
environment. It is in this configuration that the imaging specificity of your
mix can best be evaluated. Generally, in the playback check mode you want
to arrange the speakers in the same equilateral listening triangle that you do
in a nearfield setup, but instead of each side of the triangle being about 3 feet
long, the distances between stereo speakers and to your listening position
should be between 7 and 12 feet.
When setting the left and right speakers vertically, place the tweeters toward
the center with the ports toward the outside. In this vertical position, the M1
Active Mk2 becomes a “line source” speaker which is the most common
home set up. (A 12” three-way with woofer on bottom, midrange in the
center and tweeter at the top is a line source, as are most forms of tower
speakers.) When the M1 Active Mk2 is set vertically in its “column”
configuration, the horizontal dispersion (left and right) of the speaker is
widest, and the vertical dispersion (up and down) is narrowest.
Unfortunately a vertical setup will also increase room effects, so there are
minimum recommended setup distances from side and back walls: the
speakers should be a minimum of 2.5 feet from the side walls and 3 feet from
the rear walls. See the illustration on page 26.
After you’ve got the requisite distances from the side and back walls, it’s
often helpful to adjust the 7 to 12 foot equilateral listening triangle distances.
What you want to find is the maximum distance that you can separate the
two speakers while still holding a solid center image. If you get this
placement correct and you’ve done a good job in the mix, you should be
rewarded with a soundstage that accurately places the musicians in the width
and depth perspective in which they were recorded. The sound should be
very similar to what you heard at your mixing board, with possibly a little
more ambience contributed by the listening room.
The “other” playback check mode, sometimes considered of greater
importance than the home environment, is to listen to your mix over a car
audio system. Bear in mind that an expertly designed car audio system can
approach the imaging and soundstaging capabilities of an optimally setup
studio or living room, but most times this is NOT the case. The inherent
limitations of an always-off-axis listening position and the variables of
speaker placement, bass coupling (boost) in the small interior and numerous
other factors make the car environment highly suspect. So, understand the
sonic capabilities (and deficiencies) of your (or other) car audio systems, and
evaluate your mix accordingly.
M1 Active Mk2 Reference Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
PLUGGING THE PORTS TO ADJUST FOR ROOM ACOUSTICS
The low frequency response of the M1 Active Mk2s can be custom tailored by
plugging the ports. If the speakers must be placed less than one foot from a
front wall, or if they are too close to a corner, then the bass may become
exaggerated and inaccurate.
follows:
The rules of thumb for these situations are as
a) less than 1 foot from a front wall but away from any corner:
plug one port
b) less than 1 foot from a front wall and a corner:
plug both ports
The “plug” can be wad of cloth to completely block the port(s) or a more
porous material like fiberfill which will give less bass attenuation. The bass
output of the M1 Active Mk2 is thus easily variable depending on in-room
positioning and/or personal preference.
If the M1 Active Mk2s are to be used in a system with a subwoofer, the
proper blend of the two systems is critical if low-bass accuracy is to be
maintained. Here again, your ear is your most important piece of test
equipment. If the subwoofer (such as the Alesis Point One) or preamplifier
has 80Hz high-pass filters built-in for connection to the other amplifiers, then
no port plugging is necessary. The proper match will have already been
taken care of electronically. In the absence of an 80Hz high-pass filter feeding
the M1 Active Mk2s, you’ll need to experiment with various degrees of port
plugging to minimize the cancellations and nodes that can occur from bass
sources placed several feet apart in a room. In practice we’ve found that a
single port plugged with cloth is usually the best compromise. See Figure 5
below. It shows the approximate bass attenuation that can be expected with
one port plugged.
24
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
M1 Active Mk2 Reference Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
CONNECTIONS
The M1 Active Mk2 has been designed to be as simple as possible to set up
and use. However, please follow the instructions to ensure that you get the
best possible performance from your monitors.
Before connecting the speakers, make sure the power switches of the
M1 Active Mk2s and any equipment they will be connected to are
turned OFF.
AC POWER CABLE
READ ALL SAFETY WARNINGS IN THE PREVIOUS SECTION OF THIS
MANUAL TO ENSURE SAFE OPERATION OF THESE UNITS. Connect the
M1 Active Mk2s to the specified power using the AC cables supplied. The
AC cables are removable. If the distance to your AC outlet is longer or
shorter than the supplied cable, you may substitute an approved standard
NEMA-to-CEE power cable of the correct length, available from most
electronics stores.
GROUNDING
CONNECT THE M1 ACTIVES TO A PROPERLY GROUNDED OUTLET ONLY.
DO NOT USE ADAPTERS WHICH REMOVE THE SAFETY GROUND
PROTECTION OR CUT OFF THE GROUNDING PRONG ON THE POWER
CORD. Proper grounding is essential for user safety and low noise. If
you experience 60-cycle hum in your sound system as a result of
different ground potentials between different units in your system,
plug all units into the same AC circuit (if the total power load allows)
and make sure other devices in the system are properly grounded
themselves. The M1 Active features balanced inputs, so if it is properly
connected to other balanced units, AC ground potentials will not affect
the audio. If you cannot get rid of ground loops, consult a professional
electrician familiar with sound system power designs.
USE CLEAN POWER
The M1 Active Mk2's internal power supply is designed to filter out most AC
line noise. However, it is still good practice to plug your sound equipment
into an AC circuit that is not shared with lighting dimmers, refrigerators, air
conditioning units, or other appliances that may induce noise into the power
system.
26
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
POWER SWITCH
The POWER switch is located on the back panel. A blue power indicator
lamp is on the front panel.
INPUT CONNECTIONS
Almost any conventional line-level source may be plugged into the M1 Active
Mk2’s LINE INPUT jack. The Line Input jack accepts both XLR and 1/4”
input plugs wired either balanced or single-ended (unbalanced). The best
connection is to use a high-quality XLR-to-XLR “mic cable” between the
output of the source (usually, the CONTROL ROOM OUTPUT of the console)
and the speakers. A conventional 1/4” “patch cord" mono TS-type plug will
also work for unbalanced sources which automatically ground the minus
input.
Polarity: Input connector wiring is printed to the left of the connector on the
back panel and is as follows:
+ Pin 2: tip (“hot”)
- Pin 3: ring (“cold”)
Shield Pin 1: sleeve (ground)
A positive voltage on the “hot” connector will cause the drivers to move
outwards.
Unbalanced Line Input
Balanced Line Input
Signal
Tip
Hot
Tip
Cold
Ring
Sleeve
Ground
Tip
Sleeve
Ground
Tip
Sleeve
Sleeve
Ring
Direct connection of unbalanced -10 dBV line level sources: Most
synthesizers, drum machines, effect devices, cassette decks and CD players
operate at this level. Their average signal level is about 1/3 of a volt. They
have a 2-conductor output jack that is either a 1/4" phone or "RCA phono"
type. These may be plugged directly into the M1 Active Mk2’s LINE IN jacks.
M1 Active Mk2 Reference Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
But do NOT plug the speaker output of an amplifier, receiver, or similar
device into the LINE INPUT jack. Use only line-level sources. Plugging
too loud of a signal into the LINE INPUT jack may damage the
electronics.
Balanced +4 dBu line level sources: Professional recording and processing
equipment typically provides a balanced, 3-conductor signal output that is a
higher voltage (1.24 volts nominal level) than most synthesizers and stereo
equipment. The LINE INPUT jacks are designed to handle these balanced
inputs.
Balanced sources often feature XLR outputs. Connect them with an XLR-to-
XLR cable. Many consoles (such as the Alesis Studio series) feature balanced
outputs on 1/4” jacks; you may use a TRS-to-TRS balanced phone cable, or an
XLR-to-1/4 inch phone TRS (tip-ring-sleeve) cable, as shown below. The
advantage of using an XLR on the speaker side is that it is a locking connector
and cannot be accidentally disconnected.
NOTE: Use high quality input connectors which conform to industry
standard sleeve dimensions. Some off-brand connectors, particularly cheap
1/4” TRS plugs, do not provide reliable connections because of slight
dimensional differences.
SETTING THE INPUT LEVEL CONTROL
In most cases, the INPUT LEVEL control should NOT be set at full
rotation. For best system dynamic range, follow the instructions
below.
The goal is to set the input level of the M1 Active Mk2s for the desired
listening level, when all the rest of the system is at its nominal operating level.
“Nominal” means its normal average level, expecting peaks from 8 to 15 dB
above that on occasion. For the best signal-to-noise ratio, everything before
the M1 Active Mk2 should be as loud as possible. The M1 Active Mk2s’
INPUT LEVEL control, being last in the signal chain, is the worst place to
make up gain lost earlier in the system.
28
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
TO SET THE LEVEL WITH A MIXER:
1. Turn on all system components (the M1 Active Mk2s last) and turn the M1
Active Mk2’s INPUT LEVEL control all the way down.
2. Play program through the mixer and raise the mixer’s fader levels until its
meter averages around “0 VU”.
3. Raise the Control Room Output to its nominal position (usually “2
o’clock” or 3/4 of the way up).
4. On one speaker, raise its INPUT LEVEL CONTROL for a comfortable
level in the engineer’s seat (if you have a sound pressure meter, 85 dB SPL
is a common standard for listening).
5. Match the level for the other speaker. Note that the numbers on the back
panel are only a rough guide; for precise left/right imaging, use pink
noise or test tones and a sound pressure meter.
The Input Level control has a 28 dB range with a center detent. The detent has
no particular meaning, but helps in adding a mental “reference position”
when attempting to set levels from in front of the speaker. With the control at
a maximum clockwise rotation, 2.0 volt input will produce full amplifier
output (102 dB SPL “A” weighted from two speakers at 1 meter).
For the technically-minded, here is an approximate chart of SPL levels for
various settings of the INPUT LEVEL control, measured at 1 meter from two
speakers simultaneously (all settings, especially near the extremes of the
range, are subject to a plus or minus 2 dB error):
Mark
-10 dBV
nominal
-- dB SPL
--
+4 dBu
nominal
-- dB SPL
--
0 (MIN)
1
2
3
57.0
63.5
69.0
75.5
4
5
68.2
71.0
80.2
83.0
6
7
73.0
78.0
85.0*
90.0
8
9
83.5
85.5*
86.5
95.5
97.5
98.5
10 (MAX)
* denotes recommended setting for control room use
M1 Active Mk2 Reference Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Installation
AVOIDING DAMAGE
The best protection against speaker failure is to mix at a reasonable listening
level. With a +4 dBu input and the input level control set to “6”, the M1
Active Mk2 speakers produce a sound pressure level (SPL) of 85 decibels at 1
meter, which is a good working level for mixing. At maximum output before
clipping, they can generate peak levels ≥ 118 dB SPL at one meter – a level
which may cause hearing loss after prolonged exposure. While the
biamplified design of the M1 Active Mk2 avoids the common “blown
tweeter” problem of conventional designs (when a broadband amplifier clips
on a bass note, it sends unusually high energy to the tweeter, which tries to
reproduce the square wave), it is not invulnerable. If you need higher power
levels, you are not using the speaker in a near-field application. For
extremely loud mid-field and far-field monitoring, we recommend the Alesis
Monitor Two speaker with a 300-watt per channel amplifier. Many studios
will check recordings on both systems, alternating to avoid ear fatigue and to
gain perspective on the mix.
30
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound
CHAPTER 3
SURROUND SOUND
ABOUT SURROUND SOUND
Surround sound is the term used for several different systems which use
multiple channels of playback in the listening room to recreate a truly three-
dimensional sound experience. The practice of recording music-only in
surround sound is a fairly recent innovation. Surround sound for video,
however, has been around for over ten years. With modern encoding
methods, multichannel audio may be delivered to consumers on standard
video tape, video discs, and even through broadcast, with the proper encoders
(devices which take multiple channels of audio and combine them into two
channels) and decoders (used at the receiving end to split the signal back into
multiple channels).
Systems are in use which use three (left, right, and surround), five (left,
center, right, left surround, right surround, often supplemented by a sixth
subwoofer channel), and more speakers. The original Dolby Surround of
the mid-eighties was a matrixed three-channel-only system. It had left, right
and a mono surround (rear) track, which was usually played through two
surround speakers. In 1987, Dolby Pro Logic, a four-channel matrix system,
was introduced. Pro Logic added a dedicated center channel to which most
dialog was assigned. The rear surround channel was still in mono. In 1996,
Dolby Digital (AC-3) and DTS, fully discrete six-channel audio delivery
platforms with separate left-rear and right-rear channels first became
available to consumers on laserdisc and, more recently, on DVD (Digital
Versatile Disc).
With so many listeners hearing music through their multimedia systems, it is
important for engineers to produce music on surround systems, even if
they’re not working for film or video applications. Powered monitors like the
Alesis M1 Active Mk2 Biamplified Reference Monitor have proven to be a
simple, cost-effective way to add five-channel surround to control rooms.
M1 Active Mk2 Reference Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound
CENTER SPEAKERS IN MUSIC MIXES
In video applications, with left, center and right channels all set to deliver
equal output, the ear tends to hear dialog as coming only from the center
channel. (It’s a psychoacoustic effect because all right and all left channel
signals are fed to the center.)
In Dolby Pro Logic, the center channel information is derived from sum and
difference information encoded in the left and right channels. The very
attributes that make this matrix-type system viable for video application
make it less desirable for music-only reproduction. In practice, there is a hard
center dialog channel but there is also a sort of phantom mono channel
developed between the left and center channel and the right and center
channel. This between-channel phantom mono image exists because so much
of the information contained in each channel (left and center or right and
center) is identical. Hence, mono. In the few music-only recordings encoded
in Dolby Pro Logic, the derived center channel could lead to some drastic
changes in spatial perception.
In developing the M1 Active Mk2s for use as left, center and right front
channel sources, we wanted them to be useable in both audio/video and
audio-only “matrix” type applications. We discovered two, already available
solutions to the large “wall-of-mono” effect produced by Dolby Pro Logic
when playing audio-only material. The first is easy. Most home audio Dolby
Pro Logic receivers will let you take the center channel out completely by
putting the receiver in the “phantom” (no center channel) mode. It preserves
the classic stereo effect of the front channels while adding rear surround.
This method works well with most stereo-only recordings which have no
surround encoding. But it’s much better if the rear channels have true matrix
(mono) surround (like applause) encoded in the mix.
The second method of using Dolby Pro Logic gets the center channel back
into the mix. Most of these same home audio receivers have an audio-only
surround mode which significantly attenuates the output of the center
channel in relation to the left and right. The audible benefit here is that the
mix sounds like a stereo only recording but the center image (like a vocalist)
becomes a hard center. There is no image wander, as the frequencies change,
for instance. And the classic listening “sweet spot” expands dramatically,
allowing for accurate soundstage and instrument placement when listening
far off-axis. (This attenuating of the center channel for audio only is also
employed by advanced professional matrixed decoders such as the Circle
Surround, Miles Technology and Lexicon units.)
32
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound
PLACEMENT OF THE CENTER M1 ACTIVE MK2 SPEAKER
IN THE STUDIO
The left, center and right speakers should all be placed in an arc so that the
distance of all drivers to the listener is identical (see page 29). The equilateral
listening triangle as described earlier for stereo (two-channel) playback
should be retained, with the center speaker placed vertically in the center,
exactly between the left and right (vertical) M1 Active Mk2s.
It does not matter what type of M1 Active Mk2 is used for the center speaker (tweeter
in or tweeter out). Since M1 Active Mk2s are sold as pairs, a 5-channel system
requires the purchase of a single speaker, breaking up a pair. Some dealers may
request that you purchase in pairs only; others may be able to arrange purchase of a
single unit. For the rear channels, we recommend a mirror-image pair, although this
is less critical than in the front.
As discussed above, for music-only recording the signal level to the center
channel will be attenuated over the levels of the left and right speakers. As a
starting point we would recommend that you set the center channel level
–6dB below the left and right channels. To get these levels fairly accurate a
white or pink noise source (such as from a test CD) is very helpful along with
an inexpensive sound level meter (such as the Radio Shack cat. no. 33-2050).
If you are recording audio-for-video, the center channel signal level should be
the same as left and right channels. The left, center, right speaker layout
configuration can remain the same as for an audio-only mix. With all front
speakers operating at equal levels, the “sweet spot” listening area will
become very large but the “wall-of-mono” effect mentioned above (in regards
to music) will be of little consequence since most of the dialogue will be
mixed specifically into the center channel.
M1 Active Mk2 Reference Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound
PLACEMENT OF REAR SURROUNDS
The following suggestions for optimal M1 Active Mk2 placement are derived
from several sources: 1) Standard industry practice for home installations as
recommended by the manufacturers of surround encoder/decoder units; 2)
recommendations developed by Tom Holman for setting up THX surround
theater sound systems, and 3) Alesis engineers’ experience fine-tuning the
performance of the SMS Monitoring System in order to find the mounting
configuration which results in the most natural and accurate surround
placement. With the many different playback systems in use, there is room
for interpretation of what the best placement is in a control room, but the
following represents a good starting point which you are free to change to
your taste.
Vertically, the M1 Active Mk2s should be placed on the side wall of the
control room, above your head, with the woofers on top, tweeters on the
bottom. The ideal location is to have the center of the speaker (between the
woofer and tweeter) at 80% of the floor-to-ceiling height. (For a standard 8
foot ceiling height the center line would be at 96” x 80% = 76.8” from the
floor.)
Recommended positioning of surround speakers
C
20%
3’min
80%
Horizontally, place the M1 Active Mk2s slightly behind the 90° position, at
110° on each side. Make sure that at the position used, there is still at least 3
feet to the back wall of your studio. If you do not have at least 3 feet to the
back of your studio, then the speakers will work better if placed diagonally in
the rear corner as shown on the next page.
34
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound
M1 Active Mk2 Reference Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound
WALL MOUNTING
Once your have located the general area for the horizontal and vertical
position, you need to find a wall stud. Attach shelving brackets or other
commercial speaker-mounting device into the wall stud, then attach the M1
Active Mk2s to the mount, allowing room for the rear-panel input and AC
connections.
The M1 Active Mk2s weigh 19.5 lbs., so it is vitally important that any
stand they’re resting on be securely mounted through the wall material
(usually 3/4” sheetrock, which by itself does not have the strength to
support the speakers) and into a wooden stud using hardened screws
or other fastener rated to hold at least two times that weight.
36
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound
MIXING FOR DISCRETE SIX CHANNEL REPRODUCTION:
MATCHED VS. SPECIALIZED SPEAKERS
While most speaker systems for monitoring music in surround use the same
speaker cabinet in all positions, both front and rear, keep in mind that most
consumer video surround installations use a different speaker in the rear
channels. These rear speakers typically do not have the same directionality or
wide frequency response of the M1 Active Mk2s. When mixing for film,
speakers with a broad ambient, non-directional response are used to mimic
the multi-speaker situation in most movie theatres. Keep this in mind when
making music mixes with full-range high-power speakers like the M1 Active
Mk2s as the surround speakers.
The difference between music surround and video surround playback has a
long history:
• Dolby Pro Logic, which works best with dipole (i.e., speakers splayed in
different directions out of phase) surround speakers, has been the
standard for surround sound in the home for 10 years.
• The most accepted home playback medium, VHS videotape, can only play
back (mono) surround in Dolby Pro Logic. VHS will not support Dolby
Digital or DTS.
• There are only two playback mediums, laser disc and DVD, that support
Dolby Digital (discrete) and DTS (discrete). After 20 years in existence,
laser disc has only a 2% market share. Some digital satellite broadcasters
have started broadcasting in Dolby Digital, but these discrete broadcasts
will be reserved for blockbuster movies initially.
• Discrete Dolby Digital, DTS and Sony’s SDDS are most commonly mixed
for theatrical release using surround, not monopolar (direct) monitors.
• Among the recording engineers who have recorded audio-only, the
consensus seems to be that the role of the surround speaker is to give the
listener a sense of immersion in the musical event. This is done by reserving
the rear channels for audience sounds, in the case of a live recording, or
perhaps by reproducing the reverberant acoustics of the recording
environment itself. Other engineer/producers prefer using five identical
full-range speakers and mixing primary instruments and vocals into the
surround channels.
So, our basic recommendation for mixing an audio-only six channel recording
is to intentionally limit the frequency response of the rear speakers using a
graphic equalizer or high-pass (100 Hz rolloff)/low pass (12 kHz rolloff) filter
on your mixer. This will help you get a rough idea of what a home system
playback will sound like.
This arrangement will also allow your mix to sound best over a well set up
car audio system. This is because professional installers have learned that a
mobile system performs best when they concentrate on producing a
soundstage across the front of the vehicle. They do this by placing high
quality drivers in the front of the vehicle which produce frequencies from the
M1 Active Mk2 Reference Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound
mid bass (about 80Hz) on up. In the rear go the subwoofers and sometimes,
small full range drivers which provide “fill”. So, in essence, today’s best car
audio systems are designed to produce an enveloping environment very
similar to that of a home theater.
The use of M1 Active Mk2s (or any monopolar speaker) as full-range
surrounds would be useful in the following cases:
• If the surround speakers are just as important as the fronts in achieving a
specialized effect, such as completely mixing the sax in the left rear only
and a flute in the right rear.
• If you know that your mix will always be played back on a monopolar
surround system.
• If the control room is completely damped with sound absorption on all
surfaces. (This renders the reverberant-field generating properties of a
bipole/dipole speaker ineffective.)
* Dolby Surround, Dolby Pro Logic, and Dolby Digital are trademarks of Dolby Laboratories, Inc.
38
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
CHAPTER 4
TROUBLESHOOTING
TROUBLESHOOTING INDEX
If you experience problems while using the M1 Active/Surround systems,
please use the following table to locate possible causes and solutions before
contacting Alesis Technical Support for assistance.
Symptom
Hum or buzz
Cause
Solution
Ground loop
Use balanced cables.
between source and Put M1 Actives on the
speaker
same AC power circuit
as the mixer.
No sound
Speaker
disconnected
Check input cable
connections
INPUT LEVEL down Turn up input control
on back panel
AC power not on
Blue LED on front
should be on. Check
switch and power
input cable.
Unfocused sound,
bass frequencies
muddy or missing
Inputs out of phase
Check + and -
connections from mixer
to input. Verify “pin 2
is hot”.
Subwoofer being
used improperly
Install port plugs when
using a subwoofer
Poor mix
Compare to
commercial CD of
similar style: time to
remix your track....
Distorted output
Power amp
overloading
speakers
Turn down level
Damaged speaker
components
Swap channel s to see if
the problem follows the
speaker; if so contact
Technical Support
M1 Active Mk2 Reference Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
MAINTENANCE
CLEANING
The cabinet surfaces of the M1 Active Mk2 are covered with a vinyl laminate.
Clean these surfaces when necessary with a lint-free cloth dampened in warm
soapy water. USE ONLY A DRY CLOTH ON THE BACK PANEL OF THE
POWER AMPLIFIER. Do not attempt to clean the cabinet with a brush (which
may damage the surface) or a sponge (which may leave small crumbs in the
texture).
Do not attempt to clean either of the drivers.
The M1 Active Mk2/Surround speakers require no periodic maintenance.
REFER ALL SERVICING TO ALESIS
We believe that the M1 Active Mk2 is one of the most reliable powered
monitors that can be made using current technology, and should provide
years of trouble-free use. However, should problems occur, DO NOT attempt
to service the unit yourself. Service on this product should be performed only
by qualified technicians. THERE ARE NO USER-SERVICEABLE PARTS
INSIDE.
SERVICE
Before sending the M1 Active Mk2s in for repair, make sure they are faulty
and that the problem isn't being caused by something else in the system.
Distortion or noise may be caused by a defective preamp, cable, equalizer etc.,
or a loose connection in the system. Connect the speakers to a system that is
known to be working properly to check whether the monitors have
malfunctioned.
OBTAINING REPAIR SERVICE
Before contacting Alesis, check all your connections, and make sure you’ve
read the manual.
Customers in the USA and Canada: If the problem persists, call Alesis USA
at 1-800-5-ALESIS and request the Technical Support department. Talk the
problem over with one of our technicians; if necessary, you will be given a
return order (RO) number and instructions on how to return the unit. All
units must be shipped prepaid and COD shipments will not be accepted.
For prompt service, indicate the RO number on the shipping label. Units
without an RO will not be accepted. If you do not have the original packing,
ship the M1 Active Mk2 in a sturdy carton, with shock-absorbing materials
such as styrofoam blocks or “bubble-pack” surrounding the unit. Make sure
40
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
the drivers will not be pressed on by the packing in shipment. Shipping
damage caused by inadequate packing is not covered by the Alesis warranty.
Tape a note to the top of the unit describing the problem, include your name
and a phone number where Alesis can contact you if necessary, as well as
instructions on where you want the product returned. Alesis will pay for
standard one-way shipping back to you on any repair covered under the
terms of this warranty. Next day service is available for a surcharge.
Field repairs are not normally authorized during the warranty period, and
repair attempts by unqualified personnel may invalidate the warranty.
Correspondence address for customers in the USA:
Alesis Product Support
1633 26th Street
Santa Monica, CA 90404
THIS IS NOT A SERVICE LOCATION. DO NOT SHIP UNITS TO THIS
ADDRESS.
Customers outside the USA and Canada:
Contact your local Alesis distributor for any warranty assistance. The Alesis
Limited Warranty applies only to products sold to users in the USA and
Canada. Customers outside of the USA and Canada are not covered by this
Limited Warranty and may or may not be covered by an independent
distributor warranty in the country of sale. Do not return products to the
factory unless you have been given specific instructions to do so.
M1 Active Mk2 Reference Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
SPECIFICATIONS
ENCLOSURE
MATERIALS AND CONSTRUCTION
Front baffle painted in metallic charcoal-gray, one inch (1”) thick MDF with
radiused edges to minimize diffraction. Sides and rear baffle covered in
metallic charcoal-gray vinyl laminate, over five-eighths inch (0.625”) thick
MDF.
Dual ports with 45° inlet and flared front baffle outlet allow precise, phase
accurate woofer-to-port frequency transition. Ports also aid in cooling
internally mounted primary amplifier heat sink.
Flush mount, rubber woofer trim ring allows consistent power response
characteristic at wide off-axis angles. Flush-mount tweeter plate assures
smooth off-axis response.
UL-approved fiberglass acoustical damping material damps internal mid-
frequency reflections from rear of woofer cone before entering port, lessening
IM distortion.
TRANSDUCERS
LOW FREQUENCY DRIVER:
6.5” (165mm) diameter dynamic driver with proprietary non-woven carbon
fiber (NWCF) cone and 1.5” diameter, long-wind voice coil.
Dampened linear rubber surround with moderate internal damping and
constant linear displacement Nomex spider. 5 mm X-max excursion
capability.
Dual magnet structure uses top magnet in opposed (“bucking”) configuration
for magnetic shielding.
HIGH FREQUENCY DRIVER:
1” silk soft-dome tweeter with special wave guide baffle.
Low-viscosity ferrofluid cooling extends power handling while retaining
impulse response capability.
Dual magnet structure uses top magnet in opposed (“bucking”) configuration
for magnetic shielding.
42
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
CROSSOVER SECTION
Crossover type:
4th-order, 24dB/octave Linkwitz-Riley @ 2000Hz
20kΩ balanced 10kΩ unbalanced
4th order optimal Q high pass filter at 48Hz with +3 dB
equalization
Input Impedance:
Low Frequency Filter:
AMPLIFIER SECTION
LOW FREQUENCY AMPLIFIER
Rated power output:
Distortion:
Slew rate:
75 watts, 6Ω load
<0.02% THD @ 30 watts/8Ω 20Hz-20kHz
19V/µsec
Signal-to-Noise ratio:
>110dB referenced to 60 watts @ 8Ω, “A” weighted,
1kHz
HIGH FREQUENCY AMPLIFIER
Rated Power Output:
Distortion:
25 watts, 4Ω load
0.025% THD @ rated power
9V/µsec
Slew rate:
Signal-to-Noise ratio:
>112dB @ rated output
ACOUSTIC SECTION
Free-Field Frequency Response:
Lower Cutoff Frequency:
Upper Cutoff Frequency:
2dB, 50Hz to 20KHz
40Hz -10dB
23.5KHz –10dB
Maximum Peak SPL per pair: ≥ 118dB SPL @ 1m
Maximum short term SPL:
80Hz to 3.0KHz ≥ 105dB SPL @ 1m
GENERAL
Power Consumption:
120 watts with musical program, loud mix
12 watts quiescent (idle)
AC Dropout Voltage:
120V AC version: 80V AC
240V AC versions: 160V AC
Weight:
Dimensions (H x W x D):
19.5 lbs. (8.9 kg) each
15” (38.1 cm) x 8.5” (21.6 cm) x 10” (25.3 cm)
M1 Active Mk2 Reference Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
1/4” input plugs, 27
AC cables, 26
AC power, 13, 26, 43
amplifiers, 10, 12, 43
balanced, 27
placement, 17
horizontal, 21
surround, 34
vertical, 22
Playback check mode, 23
Polarity, 27
biamplified, 10
center channel, 32
crossover, 11, 43
frequency response, 43
with ports plugged, 24
front baffle, 42
fuse, 13
ports, 14
plugging, 24
power supply, 13
reflections, 17, 20, 21
Safety, 3
service, 4, 40
spacing, 19
SPL, 29
subwoofer, 24
Surround sound, 31
time alignment circuit, 12
tweeter, 11, 42
mirror to inside, 20
offset, 14
Ground loop, 39
grounding, 26
INPUT LEVEL, 28
detent, 29
interference, 7
LINE IN, 27
Magnetic shielding, 11, 42
mounting, 19
nearfield, 15
warranty, 9, 45
woofer, 11, 42
XLR, 28
noise, 26
phase, 39
44
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ALESIS LIMITED WARRANTY
ALESIS CORPORATION ("ALESIS") warrants this product to be free of defects in material and
workmanship for a period of one (1) year for parts and for a period of one (1) year for labor from the date of
original retail purchase. This warranty is enforceable only by the original retail purchaser and cannot be
transferred or assigned.
The purchaser should complete and return the enclosed warranty card within 14 days of purchase.
During the warranty period ALESIS shall, at its sole and absolute option, either repair or replace free of
charge any product that proves to be defective on inspection by ALESIS or its authorized service
representative. In all cases disputes concerning this warranty shall be resolved as prescribed by law.
To obtain warranty service, the purchaser must first call or write ALESIS at the address and telephone
number printed below to obtain a Return Authorization Number and instructions concerning where to return
the unit for service. All inquiries must be accompanied by a description of the problem. All authorized
returns must be sent to ALESIS or an authorized ALESIS repair facility postage prepaid, insured and properly
packaged. Proof of purchase must be presented in the form of a bill of sale, canceled check or some other
positive proof that the product is within the warranty period. ALESIS reserves the right to update any unit
returned for repair. ALESIS reserves the right to change or improve design of the product at any time without
prior notice.
This warranty does not cover claims for damage due to abuse, neglect, alteration or attempted repair by
unauthorized personnel, and is limited to failures arising during normal use that are due to defects in material
or workmanship in the product.
THE ABOVE WARRANTIES ARE IN LIEU OF ANY OTHER WARRANTIES OR REPRESENTATIONS
WHETHER EXPRESS OR IMPLIED OR OTHERWISE, WITH RESPECT TO THE PRODUCT, AND
SPECIFICALLY EXCLUDE ANY IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR
MERCHANTABILITY OR OTHER IMPLIED WARRANTIES. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.
IN NO EVENT WILL ALESIS BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT OR OTHER
DAMAGES RESULTING FROM THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING,
AMONG OTHER THINGS, DAMAGE TO PROPERTY, DAMAGE BASED ON INCONVENIENCE OR ON
LOSS OF USE OF THE PRODUCT, AND, TO THE EXTENT PERMITTED BY LAW, DAMAGES FOR
PERSONAL INJURY. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
THIS CONTRACT SHALL BE GOVERNED BY THE INTERNAL LAWS OF THE STATE OF CALIFORNIA
WITHOUT REFERENCE TO CONFLICTS OF LAWS. This warranty gives you specific legal rights, and you
may also have other rights required by law which vary from state to state.
This warranty only applies to products sold to purchasers in the United States of America or Canada. The
terms of this warranty and any obligations of Alesis under this warranty shall apply only within the country
of sale. Without limiting the foregoing, repairs under this warranty shall be made only by a duly authorized
Alesis service representative in the country of sale. For warranty information in all other countries please refer
to your local distributor.
ALESIS
1633 26th Street
Santa Monica, California 90404
1-(800)-5-ALESIS
PLEASE SEND IN YOUR WARRANTY CARD
for more effective service and product update notices
Alesis Corporation 1633 26th Street, Santa Monica, CA 90404
© 2001 Alesis Corporation Specifications Subject To Change Without Notice 7-51-0092 2/01
M1 Active Mk2 Reference Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
46
M1 Active Reference Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|