Agri Fab Tiller 45 03084 User Manual

OWNER'S  
MANUAL  
MODEL NO.  
45-03084  
UNivERSAL TOW BEhiND TiLLER  
• Assembly  
• Operation  
• Customer Responsibilities  
• Service and Adjustment  
• Repair Parts  
CAUTION:  
Read Rules for  
Safe Operation  
and Instructions  
Carefully  
the fastest way to purchase parts www.speedepart.com  
Printed in U.S.A.  
FORM NO. 40566 (05/09/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
TO REMOvE UNiT FROM  
CARTON  
TO iNSTALL ThE TiLLER  
GAUGE WhEELS  
Cut from top to bottom all four corners of the carton  
and lay panels flat. (See Fig. 1)  
Remove the lag screw that holds the floating hitch to  
the packing skid.  
Disassemble and discard carton's wood top and side  
supports.  
Remove four hex bolt, hex nuts and flat washer from  
the hold down brackets at the rear of the carton.  
Remove and save the two Flat Washers and Cotter  
Pins from the rear axle. Reuse when attaching gauge  
wheels.  
Assemble Gauge Wheels onto the Rear Axle with the  
extended end of Hub facing inward. Secure with the  
Flat Washers and Cotter Pins which you removed from  
the axle during unpacking. (See fig. 2.)  
Discard all other packing hardware and hold down  
brackets.  
FiG. 2  
TO iNSTALL ThE TiLLER TiNE  
ASSEMBLiES  
Attach the floating hitch to the tractor's draw bar.  
(Refer to Operating Instructions on page 7.)  
Remove the preassembled 3/8" x 2" hex bolt and 3/8"  
nylock nut from the L.H. Tine Assembly. Slide the tine  
assembly onto the Transmission Axle on the left side  
of the tiller and secure with the hex bolt and nylock nut.  
(See fig. 3.) Repeat for the R.H. side.  
FiG. 1  
3/8" NYLOCK  
NUT  
Right hand (RH) and left hand (LH) are determined  
from the drivers position while seated on the tractor.  
We recommend that you remove the Mower Deck  
before using the Tiller. Refer to your Tractor Owner's  
Manual.  
FiG. 3  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
TO iNSTALL (WhEEL)  
WEiGhTS TO TiLLER  
NOTE: Weights are not furnished with the Tiller. 30 lb.  
tractor wheel weights may be purchased to mount to the  
Tiller if extra weight is required. (Refer to the Operation  
section of this manual.)  
Remove two Carriage Bolts and Nuts from each Tine  
Shield, located approximately 3-1/2" from the front  
edge. See fig. 4.  
Place (Wheel) Weights on Tine Shield and secure with  
long Bolts and Nuts furnished with the Weights. See  
fig. 4.  
FiG. 4  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
FiG. 5  
RECOIL START HANDLE - used to start the engine  
THROTTLE CONTROL - controls engine speed  
FUEL ShUT OFF - shuts of fuel to engine  
SAFETY SWITCH - prevents engine from starting while  
tine clutch lever is engaged  
LiFT hANDLE - selects tilling or transport position by  
moving gage wheels  
CHOKE CONTROL - used when starting a cold engine  
DEPTH STAKE - controls tilling/cultivating depth  
TINE CLUTCH LEVER - starts and stops tine rotation  
FLOATING HITCH - telescoping hitch limits shock loads  
to tractor  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tiller can result in foreign objects thrown into the eyes, which can  
result in severe eye damage. Always wear safety glasses or eye shields before starting  
your tiller and while tilling. We recommend a wide vision safety mask for over the  
spectacles or standard safety glasses.  
Repeat instructions in two preceding paragraphs until  
engine fires. When engine starts, move choke control  
gradually to RUN position.  
Allow engine to warm up for a few minutes before  
engaging tines.  
hOW TO USEYOUR TiLLER  
BEFORE STARTiNGYOUR TiLLER  
FiLL ThE ENGiNE WiTh OiL! Your tiller engine is  
shipped without oil or gasoline. Add oil and gas as  
instructed in the separate engine manual.  
ATTACHING TILLER TO TRACTOR  
(See Fig. 6)  
WARNING: Never fill fuel tank indoors, or  
with the engine running, or while the engine  
is hot. Do not smoke while filling tank.  
Rear wheel weights and tire chains can be used on  
tractor if additional traction is required for tilling.  
Place Tiller on ground level and back up tractor to it.  
Slide Floating Hitch of Tiller onto the tractor drawbar  
so that the hitch pin holes line up.  
STOPPINGYOUR TILLER  
TINES  
Insert hitch pin until it extends through bottom of  
Floating Hitch. Insert hair cotter pin into hitch pin.  
Raise tiller to transport position.  
Pull forward on tine clutch lever.  
ENGINE (Refer to separate engine manual.)  
Move throttle control to "STOP" position.  
Turn shut off to "OFF" position.  
Never use choke to stop engine.  
STARTiNGYOUR TiLLER  
(Refer to separate engine manual.)  
CAUTION: The muffler and adjacent areas  
are hot!  
Check oil and gas in Tiller engine.  
Attach spark plug wire to spark plug.  
Pull forward on tine clutch lever to disengage tines.  
A safety switch prevents engine from starting while  
tines are engaged.  
FIG. 6  
Turn shut off to "ON" position.  
Move choke lever on engine to CHOKE position.  
(A warm engine may not require choking.)  
Move throttle control lever on engine to FAST  
position.  
Grasp starter handle and pull rope out slowly until  
engine reaches start of compression cycle (rope will  
pull slightly harder at this point). Let the rope rewind  
slowly.  
BREAKING INYOUR TILLER  
Break-in your belts, pulleys and the control before you  
actually begin tilling.  
Start engine with tiller attached to tractor in transport  
position. Engage Tine Clutch Lever to start tine  
rotation. Allow tines to rotate for five minutes.  
Check tine operation and adjust if necessary. See  
"TINE OPERATION CHECK" in the Service and  
Adjustments section of this manual.  
Pull rope with a rapid, continuous, full arm stroke.  
Keep a firm grip on starter handle. Let rope rewind  
slowly. Do not let starter handle snap back against  
starter.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TRANSPORTINGYOUR TILLER  
AROUND THE YARD  
Pull forward on lift handle until it locks in the up,  
transport position.  
AROUND TOWN  
Disconnect spark plug wire.  
Drain fuel tank.  
Transport in upright position to prevent oil leakage.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
CUSTOMER RESPONSIBILITIES  
Refer to the engine manual for instructions on engine maintenance.  
MAINTENANCE SCHEDULE  
Fill in dates as you  
complete regular service.  
Service Dates  
Check Engine Oil Level  
Change Engine Oil  
X
X
X*  
Service air cleaner precleaner  
Service air cleaner cartridge  
Replace spark plug  
X**  
X**  
X
Clean cooling system  
X**  
Check valve clearance  
Check for loose fasteners  
X
X
Lubricate Tiller  
X
X
Lubricate Tiller Transmission  
*Change oil every 25 hours when operating the engine under heavy load or in high temperatures.  
*Clean more often under dusty conditions or when airborne debris is present. Replace air cleaner parts, if very dirty.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
CUSTOMER RESPONSIBILITIES  
ENGINE MAINTENANCE  
WARNING: Always stop engine and  
disconnect spark plug wire before cleaning,  
lubricating or before performing any repairs  
or maintenance.  
Check oil level before each use and every 8 hours.  
Maintain engine oil as instructed in the separate  
engine manual.  
Service air cleaner every 25 hours under normal  
conditions. Clean every few hours under extremely  
dusty conditions. Poor engine performance and  
flooding usually indicates that the air cleaner should  
be serviced. To service the air cleaner, refer to the  
separate engine manual.  
Spark plug replacement is recommended every 100  
hours or yearly. Check the engine manual for correct  
plug type and gap specifications.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: Shut off (disengage) the Tine  
Clutch Lever, the Tiller Engine and the Tractor  
Engine before making any repairs.  
TO REPLACE V-BELT  
Replace V-belt if it has been damaged considerably from  
slipping under heavy loads or if it show cracks or frayed  
edges. Refer to figures 11 and 12.  
IMPORTANT: Do not move or remove the belt guide.  
If the position of the belt guide is accidentally altered,  
return it to the correct setting (6-1/2" above the tine shield  
support plate).  
Remove the screw from the top of the belt guard.  
Remove the hex nut from the rear of the guard.  
Remove the belt guard to allow access to drive belt.  
Disengage tine clutch lever and remove belt.  
FiG. 12  
Reverse above procedures for installation of new belt.  
FiG. 11  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: Shut off (disengage) the Tine  
Clutch Lever, the Tiller Engine and the Tractor  
Engine before making any repairs.  
SPARE TINE DRIVE BOLTS  
The Tiller drive components are protected from  
damage by (shearable) Grade 5 hex bolts in the  
Tine Assemblies. The hex bolts drive the tines and  
hold them in the proper location. Should the Tine  
Assemblies strike or pick up a large hidden object  
or become jammed, the hex bolts will break and the  
drive components will not be damaged.  
TINE CARE  
For best results — Tine Blades should be kept  
reasonably sharp. The Tine Blade can be sharpened  
on a grinding wheel. Do not attempt to sharpen Tines  
while they are mounted to Tiller.  
Two extra tine hex bolts and nuts are included with  
the tiller. They are located in the Tiller Stake Support  
Bracket on the rear of the Tiller.  
The tine hex bolts are designed to be loose fit. Do not  
attempt to use a bolt or pin that is larger or harder  
than the original Grade 5 hex bolts.  
STORAGE  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
Immediately prepare your tiller for storage at the end of  
the season or if the unit will not be used for 30 days or  
more.  
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
If possible, store tiller indoors and cover it to protect  
from dust and dirt.  
Cover tiller with a suitable protective cover that does  
not retain moisture. Do not use plastic. Plastic cannot  
breathe, which allows condensation to form and will  
cause your unit to rust.  
CAUTION: Never store the tiller with  
gasoline in the tank inside a building, where  
fumes may reach an open flame or spark.  
Allow the engine to cool before storing in  
any enclosure.  
ENGiNE  
Follow the instructions in the "Service & Storage"  
section of the Engine Manual.  
WARNING: Never cover Tiller while  
engine and exhaust areas are still warm.  
TiLLER  
Clean entire tiller (See "CLEANING" in the Customer  
Responsibilities section of the manual).  
Inspect and replace belts, if necessary (See  
belt replacement instructions in the Service and  
Adjustments section of this manual.  
Lubricate as instructed in the Customer  
Responsibilities section of this manual.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLEShOOTiNG  
Follow the instructions in the "Service & Storage" section of the  
Engine Manual when performing any work on the Engine.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS FOR MODEL 45-03084 UNIVERSAL TOW BEHIND TILLER  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS FOR MODEL 45-03084 UNIVERSAL TOW BEHIND TILLER  
REF. PART NO. qTY.  
DESCRIPTION  
Engine (49 State)  
Engine (California)  
Guide - Belt  
Bolt, 5/16-18 x 1-1/2" Hex Head  
Set Screw, 5/16-18 x 5/16"  
Key, Square 1/4" x 2"  
Pulley  
Nut, 1/2-12 Nylock Jam  
Nut, 1/2-12 Hex Jam  
Spring, Depth Extension  
Hitch Bracket Assembly  
Bolt, 5/16-18 x 1" Hex Head  
Locknut, 5/16-18 Hex  
Lift Handle Assembly  
Screw, Self-Tapping 1/4" x 1/2"  
Washer, 5/16" Std. Wrt.  
Ring, Retainer  
REF. PART NO. qTY.  
DESCRIPTION  
Tine & Hub Assembly - RH  
Tine & Hub Assembly - LH  
Bolt, 3/8-16 x 2"  
Bolt, Hex 5/16-24 x 1"  
Pin, Hitch  
1
40993  
40997  
48346  
1
1
1
4
1
1
1
1
1
1
1
5
9
1
3
1
1
1
1
6
1
1
1
44  
45  
46  
47  
48  
49  
50  
HA20094  
HA20088  
43054  
47600  
HA5236  
43062  
1
1
4
1
1
1
2
1
1
8
2
2
1
2
1
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
43085  
HA115321  
HA11154  
HA20176  
48733  
HA124934  
HA19860  
64282  
43063  
43064  
64343  
48840  
Bolt, 3/8-16 x 1-1/2" Hex Head  
Wheel  
HA20918  
51 R74780828  
Bolt, 1/2-13 x 1-3/4" Hex Head  
Pivot Axle Assembly  
Bolt, 3/8-16 x 1" Carriage  
Strap Frame Extension  
Pin, Clevis  
Stake, Drag  
Bracket - Wheel Weight Support  
Decal, Danger  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
HA20670  
43350  
HA20725  
HA3433  
HA20690  
HA20932  
HA20940  
25830  
43081  
Plate, Fender Support  
HA20135  
HA20184  
HA20178  
47189  
24848  
HA23199  
24847  
47810  
41576  
18 Nut, Hex 5/16-18 Nylock  
Pulley, Input  
Bolt - Shoulder  
Nut, Hex Nylock 1/4-20  
Clutch Rod  
Switch, Safety Interlock  
Lever, Clutch  
5
1
2
1
1
1
3
2
1
1
2
1
2
1
6
1
1
5
1
4
2
1
1
1
1
Bolt - 3/8-16 x 1-3/4" Hex Head  
Bolt, 1/2-13 x 5-1/2" Hex Head  
Bolt, 5/16-18 x 1" Carriage  
Belt Guard (incl. #69)  
Washer  
Strap-Frame Extension Brace  
Nut, 1/2-13 Nylock  
Decal, Danger  
Decal  
Spacer  
Washer  
Nut, Hex 5/18-11 Nylock  
Spacer  
Bolt, Hex 5/8-11 x 7-1/2"  
Pin - 1/8" x 1-1/4" Cotter  
Rod - Lift  
Anchor - Adjustment  
Washer, 17/32" x 1-1/6" x .095" Flat  
Nut - 1/2-20 Hex Jam  
Washer, 13/16" x 1-1/2" x .134" Flat  
Pin - Hair Cotter  
Shield, Tine (LH)  
Shield, Tine (RH)  
Nut, 1/4-20 Hex  
Hitch Tube Assembly  
Washer, 5/8"  
62 R74760884  
63  
64  
65  
66  
67  
68  
69  
44326  
24849  
HA14306  
HA20691  
712-3083  
HA20938  
HA20942  
HA5713  
HA15200  
712-0261  
HA7974  
48278  
HA21362  
HA20170  
19 Nut, Hex Nylock 3/8-16  
1
2
1
4
Grip, Handle  
Rivet, Pop  
Belt Guide & Idler Mounting Bracket 70  
25 C-9M5732  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
HA20134  
HA9131  
43661  
Screw, 5/16-18 x 3/4" Self Tap  
71  
72  
73  
74  
75  
76  
77  
11 Bolt, 1/4-20 x 1" Hex Head  
HA20185  
24863  
HA20119  
24843  
HA20186  
24844  
24846  
HA11496  
HA20187  
43013  
64284  
43182  
1
1
1
1
1
1
1
1
1
7
1
4
1
1
1
Key, Woodruff No. 61  
Cover, Drive  
Transmission - Complete  
Chassis, Left  
Spring, Extension  
Chassis, Right  
Bracket, Idler  
43010  
HA20688  
HA19649  
78 HA120396  
79 HA124934  
80 HA456151  
Pulley, Idler  
V-Belt  
81  
82  
83  
84  
85  
HA20481  
HA22594  
HA22595  
43178  
Nut, 1/4-20 Hex Lock  
Module  
Hex Bolt, 5/16-18 x 3/4"  
Rear Guard Assembly - LH  
Pin - Hair Cotter 5/32"  
Rear Guard Assembly - RH  
HA20112  
714-0117  
HA20113  
HA20692  
86 R19212113  
40566  
1
1
Owner's Manual  
*Standard Hardware - Purchased Locally  
the fastest way to purchase parts www.speedepart.com  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS FOR MODEL 45-03084 UNIVERSAL TOW BEHIND TILLER  
REF.  
1
2
3
4
PART NO. qTY.  
DESCRIPTION  
HA20344  
43064  
HA20123  
HA20122  
43013  
2
8
2
2
Dust Cap  
Locknut, 5/16-18 *  
Flange & Bearing Assy  
Gasket, Flange  
5
17 Locknut, 1/4-20 Hex *  
6
7
8
9
HA20120  
HA20136  
HA20127  
HA20121  
43866  
1
1
1
1
Drive Housing & Bearing Assy - LH  
Gasket, Drive Housing  
Tine Shaft Assy  
Drive Housing & Bearing Assy - RH  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
15 Bolt, Hex 1/4-20 x 5/8" Grade 8  
HA20125  
HA20124  
HA20130  
HA20129  
HA20132  
HA20128  
HA20133  
HA20131  
HA20135  
43012  
2
2
1
4
1
1
1
1
1
2
4
1
2
3
Washer, Felt  
Seal, Rubber  
Plug, Transmission Oil  
Washer, Thrust  
Chain Assembly #40  
Chain Assembly #50  
Input Shaft Assembly  
Idler Shaft Assembly  
Ring, Retainer 5/8" Dia. Shaft  
Bolt - 1/4-20 x 3/4" Hex Head *  
Bearing  
HA20137  
HA20145  
HA20155  
HA20138  
Seal  
Bearing, Flange  
Cap, Bearing  
*Standard Hardware - Purchased Locally  
the fastest way to purchase parts www.speedepart.com  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
the fastest way to purchase parts www.speedepart.com  
REPAIR PARTS  
Agri-Fab, Inc.  
809 South Hamilton  
Sullivan, IL. 61951  
217-728-8388  
© 2001 Agri-Fab, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com Switch 4226T User Manual
Acer Computer Monitor M190E5 L0A User Manual
Adder Technology Computer Accessories CATX USBA DA User Manual
Addonics Technologies Computer Drive REDESP User Manual
AMC Water System FM DWS 1500 User Manual
Atlona Home Theater Server AT AV0808N User Manual
Atlona Printer AT HD V22M User Manual
Avocent Network Card LongView Wireless Installer User Manual
Axor Plumbing Product 42280000 User Manual
Axxess Interface Automobile Accessories OESWC 8113 RF User Manual