PPC-V106
Fanless Vehicle Mounted
Terminal with 10.4" TFT LCD
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class B
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a residential environment. This
equipment generates, uses and can radiate radio frequency energy. If not
installed and used in accordance with this user's manual, it may cause
harmful interference to radio communications. Note that even when this
equipment is installed and used in accordance with this user's manual,
there is still no guarantee that interference will not occur. If this equip-
ment is believed to be causing harmful interference to radio or television
reception, this can be determined by turning the equipment on and off. If
interference is occurring, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment to a power outlet on a circuit different from that
to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Warning! Any changes or modifications made to the
equipment which are not expressly approved by
the relevant standards authority could void your
authority to operate the equipment.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing List
Before you begin installing your card, please make sure that the following
materials have been shipped:
• PPC-V106 series panel PC
• Accessories for PPC-V106
- Warranty card
- Power cord:
For AC Model: US type AC power cord.
For DC Model: DC power inlet cable (180cm)
-"Drivers, Utilities and User Manual" CD-ROM
- Packet of screws
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
PPC-V106 User Manual
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information and Assistance
www.advantech.com.tw where you can find the latest informa-
tion about the product.
Step 2. Contact your distributor, sales representative, or Advantech's cus-
tomer service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
1. Input voltage rated:Input voltage rated :
AC model: 100-240 Vac, 50/60Hz, 2-1.5A.
DC model
Warning!
a. 19-36 Vdc
b. 11.2-18 Vdc
c. 40-58 Vdc
2. Use a 3 V @ 195 mA lithium battery
3. Packing: please carry the unit with both hands, han-
dle with care
4. Maintenance: to properly maintain and clean the sur-
faces, use only approved products or clean with a dry
applicator
5. CompactFlash: Turn off power before inserting or
removing CompactFlash storage card.
Contact information:
Our European representative:
Advantech Europe GmbH
Kolberger Straße 7
D-40599 Düsseldorf, Germany
Tel: 49-211-97477350
Fax: 49-211-97477300
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or let-
ting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE
THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR
ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE
EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED.REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED
BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUC-
TIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-
tech disclaims all responsibility for the accuracy of any statements contained
herein.
PPC-V106 User Manual
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch
zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen
oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit-
zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.
Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu
beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädi-
gung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten
in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-
lösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen
und von einer qualifizierten Servicestelle zu überprüfen:
a - Netzkabel oder Netzstecker sind beschädigt.
b - Flüssigkeit ist in das Gerät eingedrungen.
c - Das Gerät war Feuchtigkeit ausgesetzt.
d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert
oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batte-
rie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-
mahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des
Herstellers.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70dB(A) oder weiger.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
DISCLAIMER: This set of instructions is given according to IEC704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.
PPC-V106 User Manual
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Figure 4.1:Locating Jumpers on the PPC-V106 Mother-
board ................................................................. 21
Figure 4.2:Locating Connectors on the PPC-V106 Moth-
erboard.............................................................. 23
ix
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
PPC-V106 User Manual
x
Download from Www.Somanuals.com. All Manuals Search And Download.
xi
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
PPC-V106 User Manual
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
General Information
This chapter gives background
information on the PPC-V106 panel
PC.
Sections include:
• Introduction
• General Specifications
• LCD Specifications
• Dimensions
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 General Information
1.1 Introduction
PPC-V106 is fanless and comes with a VIA Eden low-power CPU for
higher reliability and performance. The ruggedized aluminum enclosure
without ventilation holes makes PPC-V106 waterproof and dust proof.
A variable power source suits vehicles such as forklifts and trucks, which
typically operate anywhere from 12 to 48 VDC.
PPC-V106 provides 10/100Base-T Ethernet, and expansion ability for
wireless transmissions, ex : 802.11g/b, GPS, GPRS and CDMA..etc..
Embedded OS support (WinCE.NET 4.2, WinXP Embedded), using OS
images can greatly shorten system development and troubleshooting.
1.2 General Specifications
General
•
Dimensions (W x H x D): 310 x 255 x 80 mm
• Weight: 3.5 kg
• Power supply:
AC model: 60 watts
Input voltage: 100-240 Vac, 50/60Hz, 2-1.5A
Output voltage: +5V@5A, +12V@3A
DC model: 75 watts
Input voltage: 19-36 Vdc , typical 24V DC.
Output voltage: +5V@8A, [email protected]
Optional DC model: 65 watts
Input voltage: 11.2-18 Vdc , typical 12 V DC.
Output voltage: +5V@7A, +12V@2A
Optional model: 75 watts
Input voltage: 40-58 Vdc , typical 48 V DC.
Output voltage: +5V@8A, [email protected]
• Disk drive housing: Space for one 2.5" HDD
• Front panel: IP65/NEMA4 compliant
• Enclosure: Ruggedized aluminum without ventilation holes
PPC-V106 User Manual
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard PC functions
• CPU: Embedded VIA Eden 800 MHz CPU
• BIOS: Award 256 KB Flash BIOS, supports Plug & Play, APM
• System Chipset: VIA CLE266 and VT8235 CD
• Front side bus: 133 MHz
• System Memory: Two 184-pin DIMM sockets, accepts up to 2 GB
DDR 266 SDRAM
• PCI bus master IDE interface: Supports two connectors. Each con-
nector has one channel and supports two IDE devices. Each channel
supports PIO modes 0 ~ 4, DMA mode 0 ~ 2, and Ultra DMA 33/66/
100 simultaneously. The secondary connector is designated for the CD-
ROM drive or CompactFlash card. BIOS supports IDE CDROM boot-
up
• Keyboard/mouse connector: Supports 1 standard AT Keyboard and a
PS/2 Mouse
• Serial ports: Three serial ports with two RS-232 ports (COM 1, COM
3), and one RS-232/422/485 port (COM2). All ports are compatible
with 16C550. UARTs, +5V/+12V power supply selectable
• Universal serial bus (USB) port: Supports up to two V2.0 USB ports,
Intel UHCI v1.1 compatible
• Mini PCI bus expansion slot: Accepts one type lll mini PCI bus card
• Solid State Disk: Supports one 50-pin socket for CompactFlash type I/
II (True IDE mode) or IBM MicroDrive HDD
• Watchdog timer: 63-level timer intervals automatically generates sys-
tem reset or IRQ11 when the system stops due to a program error or
EMI. Jumperless selection and software enabled/disabled
• Battery: 3.0 V @ 195 mA lithium battery
• Power management: Supports power saving modes including Normal/
Standby/Suspend modes. APM 1.2 compliant
VGA/Flat panel interface
• Chipset: Integrated in VIA CLE266
• Frame Buffer: Supports 8 / 16 / 32 / 64MB frame buffer using system
memory
• Display type: Simultaneously supports CRT and flat panel displays
(EL, LCD and gas plasma)
3
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio function
• Chipset: Integrated in VT8235CD South Bridge
• Audio controller: AC97 Ver. 2.0 compliant interface, Multi stream
Direct sound and Direct Sound 3D acceleration
• Stereo sound: 18-bit full-duplex codec
• Audio interface: Line out
PCI bus Ethernet interface
• Chipset: Realtek RTL8100C PCI local bus Ethernet controller
• Ethernet interface: Full compliance with IEEE 802.3u 100Base-T and
10 Base-T specifications. Includes software drivers and boot
ROM.(Support both RPL and PXE).
• 100/10Base-T auto-sensing capability
PCMCIA interface
• Chipset: R5C554
• Cardbus Controller: A PC card controller offers a single chip solution
as a bridge between the PCI bus and the Cardbus
• PCI bus interface: Complies with PCI Local Bus Specification 2.1,
and supports the 32-bit Cardbus (Card-32) and the 16-bit PC card
(Card-16) without external buffers
• Hot insertion and removal
Touchscreen (Optional)
Type
Analog Resistive
Infrared
Light Transmission
Controller
75%
91%
RS-232 interface
(uses COM4)
RS-232 interface
(Use COM4)
Power Consumption
Durability
<5 V@ 100 mA
above 10 million
Supports Win-
+5 V @ 150 mA
100,000 hrs
Software Driver
Supports Win-
dows 98/2000/ME/ dows and DOS
XP
PPC-V106 User Manual
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Environment
• Operating Temperature: 0 ~ 45° C (32 ~ 122° F)
• Storage Temperature: -20 ~ 60° C
• Relative Humidity: 10 ~ 95% @ 40° C (non-condensing)
• Shock: 10 G peak acceleration (11 msec duration)
• Certifications: EMC: CE, FCC. Safety: UL1950.
• Vibration: 5 ~ 500 Hz 1 G RMS Random vibration n (operating with
HDD)
1.3 LCD Specifications
• Display type: 10.4" TFT LCD
• Max. resolution: 800 x 600
• Colors: 256 K
• Dot size (mm): 0.264 x 0.264
2
• Luminance: 230 cd/m
• Temperature: 0 ~ 50° C
• *VR control: Brightness
• LCD MTBF: 50,000 hours
• Backlight lifetime: 20,000 hours
* The VR control is defined by hot key in DOS or BIOS mode as
below: Ctrl-Alt-F3, Ctrl-Alt-F4.
Note:
The color LCD display installed in the panel PC
is high-quality and reliable. However, it may
contain a few defective pixels which do not
always illuminate. With current technology, it is
impossible to completely eliminate defective
pixels. Advantech is actively working to improve
this technology.
5
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
2
System Setup
This chapter details system setup on the
PPC-V106 Panel PC.
Sections include:
• A Quick Tour of the Panel PC
• Installation procedures
• Running the BIOS Setup Program
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 System Setup
2.1 A Quick Tour of the Panel PC
Before you start to set up the panel PC, take a moment to become familiar
with the locations and purposes of the controls, drives, connectors and
ports, which are illustrated in the figures below.
When you place the panel PC upright on the desktop, its front panel
appears as shown in Figure 2-1
Figure 2.1: Front View of the Panel PC
When you look at the right side of the panel PC, you will see the holes for
mounting as shown in Fig. 2-2.
Figure 2.2: Right Side of Panel PC
PPC-V106 User Manual
8
Download from Www.Somanuals.com. All Manuals Search And Download.
When you turn the Panel PC around and look at its rear cover, you will
find VESA standard holes and others for mounting. There are no ventila-
tion holes, as shown in Figure 2-3.
Figure 2.3: Rear Side View of the Panel PC
The I/O section is at the bottom of the panel PC, as shown in Fig. 2-4.
1
2
3
Figure 2.4: Panel PC I/O (DC model)
9
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Installation Procedures
2.2.1 Connecting the Power Cord
There are two kinds of power supplies for the PPC-V106 series, AC and
DC.
For AC model :
The Panel PC can only be powered by an AC electrical outlet (100 ~ 250
volts, 50 ~ 60 Hz). Be sure to always handle the power cords by holding
plug ends only. Follow these procedures in order:
1.
Connect the female end of the power cord to the AC inlet of the
panel PC.
2.
Connect the 3-pin male plug of the power cord to an electrical out-
let.
For DC model :
Connect the 2 pin waterproof power cord to the DC inlet of the panel PC.
2.2.2 Connecting the Keyboard or Mouse
Before you start the computer, please connect the necessary mouse or
keyboard to the PS/2 mouse, keyboard port or serial ports.
2.2.3 Switching On the Power
When you look at the bottom of the panel PC, you will see the power
switch.
PPC-V106 User Manual
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Running the BIOS Setup Program
Your panel PC is likely to have been properly set up and configured by
your dealer prior to delivery. You may still find it necessary to use the
panel PC's BIOS (Basic Input-Output System) setup program to change
system configuration information, such as the current date and time or
your type of hard drive. The setup program is stored in read-only memory
(ROM). It can be accessed either when you turn on or reset the panel PC,
by pressing the "Del" key on your keyboard immediately after powering
on the computer.
The settings you specify with the setup program are recorded in a special
area of memory called CMOS RAM. This memory is backed up by a bat-
tery so that it will not be erased when you turn off or reset the system.
Whenever you turn on the power, the system reads the settings stored in
CMOS RAM and compares them to the equipment check conducted dur-
ing the power on self-test (POST). If an error occurs, an error message
will be displayed on screen, and you will be prompted to run the setup
program.
11
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Installing System Software
Recent releases of operating systems from major vendors include setup
programs which load automatically and guide you through hard disk
preparation and operating system installation. The guidelines below will
help you determine the steps necessary to install your operating system
on the panel PC hard drive.
Note:
Some distributors and system integrators may
have already pre-installed system software
prior to shipment of your panel PC.
If required, insert your operating system's installation or setup diskette
into the diskette drive until the release button pops out.
The BIOS of the panel PC supports system boot-up directly from the CD-
ROM drive. You may also insert your system installation CD-ROM into
the CD-ROM drive.
Power on your panel PC or reset the system by pressing the
"Ctrl"+"Alt"+"Del" keys simultaneously. The panel PC will automati-
cally load the operating system from the diskette or CD-ROM.
If you are presented with the opening screen of a setup or installation pro-
gram, follow the instructions on screen. The setup program will guide
you through preparation of your hard drive, and installation of the operat-
ing system.
If you are presented with an operating system command prompt, such as
A:\>, then you must partition and format your hard drive, and manually
copy the operating system files to it. Refer to your operating system user's
manual for instructions on partitioning and formatting a hard drive.
PPC-V106 User Manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Installing the Drivers
After installing your system software, you will be able to set up the Ether-
net, SVGA, audio, and touchscreen functions. All the drivers except the
CD-ROM drive driver are stored in a CD-ROM disc entitled "Drivers and
Utilities." The CD-ROM drive driver is stored in a floppy disk. Both the
CD-ROM and the floppy disk can be found in your accessory box.
To set up the CD-ROM function, insert the floppy disk with the CD-ROM
drive driver into the floppy disk drive and type "install" after the follow-
ing prompt is displayed on screen:
A: > INSTALL
Press "Enter", and the installation process will be completed in a few sec-
onds.
The standard procedures for installing the drivers are described in Chap-
ters 5, 6, 7, 8 respectively.
The utility directory includes multimedia programs. Refer to the
README.TXT file inside the VGA folders for more detailed informa-
tion.
The various drivers and utilities in the CD-ROM disc have their own text
files which help users install the drivers and understand their functions.
These files are a very useful supplement to the information in this man-
ual.
Note:
The drivers and utilities used for the PPC-V106
panel PCs are subject to change without notice. If
in doubt, check Advantech's website or contact
our application engineers for the latest informa-
tion regarding drivers and utlities.
13
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
PPC-V106 User Manual
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Hardware and
Peripheral Installation
This chapter details the installation of
the PPC-V106 panel PC hardware.
Sections include:
• Overview of Hardware Installation
and Upgrading
• Installing the 2.5" Hard Disk Drive
• Installing the Universal Arm
• Placing the Rubber Seal
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Hardware and Peripheral
Installation
3.1 Overview of Hardware Installation and Upgrading
The panel PC consists of a PC-based computer that is housed in a rugge-
dized aluminum enclosure. Any maintenance or hardware upgrades can
be completed after removing both panels..
Warning! Do not remove the ruggedized aluminum covers
until you have verified that no power is flowing
within the panel PC. Power must be switched off
and the power cord must be unplugged. Every
time you service the panel PC, you should be
aware of this.
3.2 Installing the 2.5" Hard Disk Drive (HDD)
You can attach one enhanced Integrated Device Electronics (IDE) hard
disk drive to the panel PC's internal controller which uses a PCI local-bus
interface. The advanced IDE controller supports faster data transfer and
allows the IDE hard drive to exceed 528 MB. The following are instruc-
tions for installation:
1.
Detach the HDD bracket by unscrewing the four screws (#2) on the
top of the HDD bracket.
2
Screw
1
2
1930030400-M3x4L
1933030500-M3x5L
PPC-V106 User Manual
16
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Place the HDD inside the HDD bracket and tighten four screws
(#1) from both sides of the HDD bracket.
HDD (Bottom up)
Pin 1
1
3.
The HDD cable (1 x 44-pin to 1 x 44-pin) is next to the HDD
bracket. Connect the HDD cable to the HDD. Make sure that the
red wire corresponds to Pin 1 on the connector, which is labelled on
the board. Plug the other end of the cable into the HDD, with Pin 1
on the cable corresponding to Pin 1 on the HDD.
3.3 Placing the Rubber Seal
To ensure that your PPC-V106 stays dry, the supplied rubber seal must be
placed correctly between the front bezel and back cover. Please note the
direction of the seal. The mark should be up.
Marked
Flat (UP)
UP
Figure 3.1: Placing the Rubber Seal
17
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 Installing the Universal Arm
1.
Press latches at the same time and then rotate support-1 until you
can see both of the screw holes.
2.
3.
Rotate support-2 until the angle is the same as support-1.
Use four M4x8L screws and attach the U-Arm with the PPC-V106.
The 4 stainless screws can be found in the universal arm's box.
4.
Use latches adjust the angle of PPC-V106 (every 14.4° on 360°).
Note: Support-1 can be on the right or left.
Latch
Support-1
Support-2
Screw-M4x8L
(x4)
PPC-V106
Figure 3.2: Universal Arm
PPC-V106 User Manual
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Jumper Settings and
Connectors
This chapter tells how to set up the
panel PC hardware, including instruc-
tions on setting jumpers and connecting
peripherals, switches and indicators. Be
sure to read all the safety precautions
before you begin the installation proce-
dures.
Sections include:
• Setting Jumpers
• CPU Installation
• CMOS Clear for External RTC (JP1)
• COM-port Interface
• VGA Interface
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Jumper Settings and Connectors
4.1 Setting Jumpers
You can configure your panel PC to match the needs of your application
by setting jumpers. A jumper is the simplest kind of electrical switch. It
consists of two metal pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect them. To “close” a
jumper, you connect the pins with the clip. To “open” a jumper you
remove the clip. Sometimes a jumper will have three pins, labeled 1, 2,
and 3. In this case, you would connect either pins 1 and 2 or pins 2 and 3.
open
open
closed
closed
closed 2-3
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your
application, contact your local distributor or sales representative before
you make any changes.
An arrow is used on the motherboard to indicate the first pin of jumpers.
PPC-V106 User Manual
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.1 Jumpers and Switches
The motherboard of the panel PC has a number of jumpers that allow you
to configure your system to suit your applications. The table below lists
the function of each of the boardís jumpers.
Table 4.1: Jumpers and their functions
Label
JP1
Function
CMOS clear for external RTC
LCD power connector
JP2
JP3
COM1 / COM2/ COM3 pin 9 output type setting
COM1 / COM2/ COM3 pin 9 output type setting
COM2 RS232/422/485 setting
Panel type setting (Reserved)
JP4
JP5
SW1
4.1.2 Locating Jumpers and Switches
Figure 4.1: Locating Jumpers on the PPC-V106 Motherboard
21
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.3 Connectors
Onboard connectors link the panel PC to external devices such as hard
disk drives or floppy drives. The table below lists the function of each of
the board ís connectors.
Table 4.2: Panel PC connectors
Label
CN1
Function
Power input connector
Flat panel display connector (Reserved)
LVDS connector
CN2
CN4
CN8
SIR connector (Reserved)
Inverter power connector
Print port connector
CN10
CN11
CN12
CN13
CN14
CN15
CN16
CN17
CN18
CN20
CN21
CN23
CN24
CN26
CN27
Line/Mic in connector (Reserved)
Line out connector
Internal Speaker connector (Reserved)
2.5 " IDE connector
Floppy drive connector (Reserved)
CFC connector
Slim type CD-ROM/IDE connector
USB 3
USB 4
COM4 connector
Mini PCI socket
COM 3 connector
Front panel connector
PPC-V106 User Manual
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 CMOS Clear for External RTC (JP1)
Warning: To avoid damaging the computer, always turn
off the power supply before setting “Clear
CMOS”. Set the jumper back to “Normal opera-
tion” before turning on the power supply.
Table 4.3: Clear CMOS / External RTC (JP1)
*Normal operation (default)
Clear CMOS
2
3
2
3
1
1
4.4 COM-port Interface
The panel PC provides three serial ports: COM1, COM 3 : RS-232 and
COM2: RS-232/422/485 (in one COM port connector).
4.4.1 COM2 RS-232/422/485 Setting (JP5)
COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode.
This is done via JP5 settings.
Table 4.4: COM2 RS-232/422/485 setting (JP5)
*RS-232
2
10
18
6
5
6
14
13
14
1
2
9
17
18
RS-422
RS-485
10
5
6
9
13
14
1
2
17
18
10
5
9
13
1
17
PPC-V106 User Manual
24
Download from Www.Somanuals.com. All Manuals Search And Download.
The IRQ and the address ranges for COM1, COM2, COM3 and COM4
are fixed.
However, if you wish to disable the port or change these parameters later
you can do this in the system BIOS setup. The table overleaf shows the
default settings for the panel PC’s serial ports.
COM1 and COM2 are one set. You can exchange the address range and
interrupt IRQ of COM1 for the address range and interrupt IRQ of
COM2. After exchanging:
COM1's address range is 2F8 ~ 2FF and its request IRQ is IRQ3.
COM2's address range is 3F8 ~ 3FF and its interrupt IRQ is IRQ4.
COM3 and COM4 are another set. You can exchange the address range
and interrupt IRQ of COM3 for the address range and interrupt IRQ of
COM4.
COM3’s address range is 3E8 ~ 3EF and its request IRQ is IRQ10.
COM4’s address range is 2E8 ~ 2EF and its request IRQ is IRQ5.
.
Table 4.5: Serial port default settings
Port
Address Range
Interrupt
COM1
COM2
COM3
COM4
3F8 ~ 3FF
2F8 ~ 2FF
3E8~3EF
2E8~2EF
IRQ4
IRQ3
IRQ10
IRQ 5
25
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4.2 COM1/COM2/COM3/ Pin 9 Output Setting (JP4)
Table 4.6: COM1/2/3 Pin 9 Output Setting(JP4)
Normal
(default)
11
9
7
5
3
1
2
12 10
8
7
6
5
4
3
+5 V output
11
9
1
12 10
8
7
6
5
4
3
2
1
+12 V output
11
9
12 10
8
6
4
2
NOTE:
Pins 1, 3 and 5 are for COM1
Pins 2, 4 and 6 are for COM2
Pins 7, 9 and 11 are for COM3
When enabling this function, you should remove a jumper from JP3 as
shown in table 4.7.
PPC-V106 User Manual
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4.7: JP3 Setting
Normal (default)
7
8
5
3
1
6
5
4
3
2
1
Remove jumper from pin
1 and 2 to make pin 9 on
COM1 a power output.
7
8
6
5
4
3
2
1
Remove jumper from pin
3 and 4 to make pin 9 on
COM2 a power output.
7
8
7
6
5
4
3
2
1
Remove jumper from pin
5 and 6 to make pin 9 on
COM3 a power output.
8
6
4
2
27
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
4.5 VGA Interface
The panel PC's AGP VGA interface can drive conventional CRT dis-
plays. It is also capable of driving a wide range of flat panel displays,
including electroluminescent (EL), gas plasma, passive LCD and active
LCD displays. The board has two connectors to support these displays
simultaneously: one for standard CRT VGA monitors, and one for flat
panel displays.
Pin assignments for the flat panel display connector, backlight connector
and other related connectors are shown in Appendix C.
4.5.1 LCD Panel Power Setting
The panel PC's AGP SVGA interface supports 5 V and 3.3 V LCD dis-
plays. The default setting is 3.3 V (connecting pin 2 and 3), but you can
use JP2 to change this to 5 V. (connecting pin 1 and 2).
PPC-V106 User Manual
28
Download from Www.Somanuals.com. All Manuals Search And Download.
5
VIA Chipset
This chapter provides information on
Intel chipset configuration
• Introduction
• Further information
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 VIA Chipset
5.1 Introduction
The PPC-V106 uses the combination of VIA CLE266 north bridge and
VT8235 CD south bridge.
The VIA CLE266 chipset is an innovative integrated graphics chipset
developed with DDR266 memory and optimized to support the VIA C3
and VIA Eden Series processors, adding intelligence to help manage and
prioritize multiple threads received from the microprocessor. VIA
CLE266 Combines a fully integrated video processing feature set, 2D/3D
graphics engine and ultra efficient VIA DDR memory controller, the VIA
CLE266 Chipset is designed to enable high quality digital video stream-
ing and DVD playback in a new generation of fanless, small form factor
PCs.
Important:
The following are examples only. You must follow
the instructions and pay attention to the instruc-
tions which then appear on your screen.
Note:
The CD-ROM drive is designated as "D" through-
out this chapter.
5.1.1 Installation 4-in-1 Driver for Windows 98/2000/XP
1.
2.
3.
Path: D:\PPC-V106\4in1\4in1443v.exe
Press "Next ìto proceed, then press "Finish".
Choose "Yes, I want to restart my computer", and press "Finish",
the system will reboot automatally
5.2 Further Information
For further information about the AGP/VGA installation in PPC-V106,
including driver updates, troubleshooting guides and FAQ lists, visit the
following web sites:
VIA website: www.via.com.tw
Advantech websites: www.advantech.com
PPC-V106 User Manual
30
Download from Www.Somanuals.com. All Manuals Search And Download.
6
AGP SVGA Setup
• Introduction
• Installation of SVGA Driver
-
-
for Windows 98/ME
for Windows 2000/XP
• Further Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 AGP SVGA Setup
6.1 Introduction
The PPC-V106 has an onboard integrated VGA chipset The specifica-
tions and features are described as follows:
6.1.1 Chipset
The VIA CLE266 boasts a complete integrated VIA 128-bit 2D/3D
graphics engine with a high quality video processing unit including
MPEG-2 decoding, video scaling and Alpha Blending.
6.1.2 Display memory
The integrated VGA chipset can support 8 / 16 / 32 / and 64 MB frame
buffer using system memory.
6.2 Installation of SVGA Driver
Important:
Note:
The following are examples only. You must fol-
low the instructions and pay attention to the
instructions which then appear on your screen.
The CD-ROM drive is designated as "D"
throughout this chapter.
PPC-V106 User Manual
32
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2.1 Installation for Windows 98/ME
1.
Click the 'Start' button in the task bar, click 'Run' and then select
'Setup.exe' from D:\PPC-S154\845G Graphics
Driver\WIN9X_ME\Setup.exe. The Install dialog will appear.
2.
3.
4.
Click 'Next' to continue.
Read License Agreement and click "Yes" to proceed.
When the 'Setup COMPLETE' message appears click 'Finish' to
restart PPC-V106.
5.
6.
After the system reboot, the screen show "Insert Disk", click "OK"
click "browse"
6.2.2 Installation for Windows 2000/XP
1.
Click the 'Start' button in the task bar, click 'Run' and then select
'Setup.exe' from D:\PPC-V106\VGA\2k_xp\Setup.exe. The Install
dialog will appear.
2.
3.
4.
click 'Next' to continue.
Read License Agreement and click "Yes" to proceed.
When the 'Setup COMPLETE' message appears click 'Finish' to
restart PPC-V106.
6.3 Further Information
For further information about the AGP/SVGA installation in your PPC-
V106, including driver updates, troubleshooting guides and FAQ lists,
visit the following web resources:
VIA website: www.via.com.tw
Advantech website:www.advantech.com
33
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
PPC-V106 User Manual
34
Download from Www.Somanuals.com. All Manuals Search And Download.
7
PCI Bus Ethernet Interface
This chapter provides information on
Ethernet configuration.
• Introduction
• Installation of Ethernet Driver
- for Windows 98/ME
- for Windows 2000/XP
• Further Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 PCI Bus Ethernet Interface
7.1 Introduction
The PPC-V106 is equipped with a high performance 32-bit Ethernet
chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD
standards. It is supported by major network operating systems. It is also
both 100Base-T and 10Base-T compatible.
The Ethernet port provides a standard RJ-45 jack. The network boot fea-
ture can be utilized by incorporating the boot ROM image files for the
appropriate network operating system. The boot ROM BIOS files are
combined with system BIOS, which can be enabled/disabled in the BIOS
setup.
7.2 Installation of Ethernet Driver
Before installing the Ethernet driver, note the procedures below. You
must know which operating system you are using in your PPC-V106, and
then refer to the corresponding installation flow chart. Then just follow
the steps described in the flow chart. You will quickly and successfully
complete the installation, even if you are not familiar with instructions for
Windows.
Important: The following are examples only. You must follow
the instructions and pay attention to the instruc-
tions which then appear on your screen.
Note:
The CD-ROM drive is designated as "D" through-
out this chapter.
PPC-V106 User Manual
36
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2.1 Installation for Windows 98/ME
1.
If the Operating System's New Hardware Wizard prompts you with
"New Hardware Found" for the "PCI Ethernet Controller", you
should click "Next" until "Finish" is clicked, without specifying
location of the driver. You will see "PCI Ethernet Controller" in the
Device Manager.
2.
You can then install or update the NDIS driver with the "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you with steps to install or
upgrade the driver.
b) setup -s: The InstallShield will complete the installation or upgrade
without prompting you for any instructions.
You need to reboot the system immediately after the Install shield
completes the installation/upgrade.
3.
4.
Do not click "Cancel" during New Hardware Wizard searches for
the driver.
4. You can remove RTLSetup utility from Add/Remove Program
Palette in Control Panel, the InstallShield will prompt you the steps
to remove the driver. After remove the driver, please restart the
system immediately.
7.2.2 Installation for Windows 2000/XP
After finishing the Windows 2000/XP installation, the system will auto-
matically detect the Ethernet hardware and install the Ethernet driver
from the drivers database from Windows 2000, Windows XP when the
system reboots.
It is recommended that you upgrade to the Intel driver provided with the
CD. To upgrade to this driver, use this path : D:\PPC-V106\Lan\setup.exe
37
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
2
8
Audio
• Introduction
• Installation of Audio Driver
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 Audio
8.1 Introduction
The ALC202 is an 18-bit, full duplex AC'97 2.2 compatible stereo audio
CODEC designed for PC multimedia systems, including host/soft audio
and AMR/CNR based designs. The ALC202 AC'97 CODEC supports
multiple CODEC extensions with independent variable sampling rates
and built-in 3D effects.
8.2 Installation of Audio Driver
Before installing the audio driver, please take note of the procedures
detailed below. You must know which operating system you are using in
your PPC-V106, and then refer to the corresponding installation proce-
dure.
Important:
The following are examples only. You must fol-
low the instructions and pay attention to the
instructions which then appear on your screen.
Note:
The CD-ROM drive is designated as "D"
throughout this chapter.
Run the setup.exe program to finish the installation.
Path : D:\PPC-V106\Audio\Setup.exe
PPC-V106 User Manual
40
Download from Www.Somanuals.com. All Manuals Search And Download.
9
USB 2.0
This chapter describes how to install
the USB 2.0 driver
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 USB 2.0
9.1 Installation of USB 2.0 Driver
Before installing the audio driver, please take note of the procedures
detailed below. You must know which operating system you are using in
your PPC-V106, and then refer to the corresponding installation proce-
dure
Important : The following Windows illustrations are exam-
ples only. You must follow the instructions and
pay attention to the instructions that appear on
your screen.
Note:
The CD-ROM drive is designated as "D"
throughout ths chapter.
9.2 Driver Installation for Windows XP
1.
Microsoft EHCI drivers for Windows XP are not included in this
package due to legal issues. Please install Microsoft Windows XP
Service Pack 1 before running the setup program. SETUP.exe will
redirect you to Microsoft Windows Update to download the driv-
ers, please make sure an internet connection is set up.
A. Select “Install USB 2.0 Host driver”
B. Click “Yes” and the setup program will connect to the Windows
Update web site.
2.
3.
SETUP.exe launches Microsoft Internet Explorer and opens http://
windowsupdate.microsoft.com. Click on the “Scan for updates” to
get the latest updates.
Microsoft Windows Update lists all available updates on the web-
site. It is recommended to download the Windows XP Service
Pack 1 since Microsoft EHCI drivers will be included.
PPC-V106 User Manual
42
Download from Www.Somanuals.com. All Manuals Search And Download.
9.3 Driver Installation for Windows 2000
1.
2.
Install Service Pack 3 or above before running the setup program.
Open the Device Manager and check if there is a “Universal Serial
Bus (USB) Controller” under “Other devices”.
3.
4.
Execute the setup program by double click on the “SETUP.exe” file
in \PPC-V106\USB2.0
The screen shows the VIA Software License Agreement. Please
read it FIRST and press “Yes” if wish to further proceed with the
driver installation.
5.
6.
7.
Press “Next”.
Select “Install USB Driver” and press “Next”.
The screen shows the Microsoft Software License Agreement.
Please read it FIRST and press “Yes” if wish to further proceed
with the driver installation.
8.
9.
Press “OK”.
Press “Print to File”.
10. Press “OK”.
11. Press “Finish” and the Microsoft EHCI drivers for Windows 2000
are now installed successfully.
Note: For driver uninstallation, you can remove the “Microsoft USB 2.0
Host Controller Driver” by selecting the “Uninstall” button. This will
completely remove the driver from the system.
43
Chapter9
Download from Www.Somanuals.com. All Manuals Search And Download.
9.4 Driver Installation for Windows ME / 98 / 98SE
1.
Open the Device Manager and check if there is a yellow exclama-
tion mark on any one of the “VIA Tech 3038 PCI to USB Universal
Host Controller” items.
2.
Execute the setup program by double click on the “SETUP.exe” file
in \PPC-V106\USB2.0
3.
4.
5.
Press “Next”.
Select “Install USB Driver” and press “Next”.
Press “Finish” and this will RESTART the computer system.
Please remember to SAVE all files before clicking the “Finish” but-
ton.
Note: For Driver Uninstallation, the user can remove the “Microsoft USB
2.0 Host Controller Driver” by selecting the “Uninstall” button. This will
completely remove the driver from the system.
9.5 Further Information
PPC-V106 User Manual
44
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Touchscreen
• Introduction
• Installation of Touchscreen Drivers
-
-
for Windows 98/ME
for Windows 2000/XP
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 Touchscreen
10.1 Introduction
10.1.1 General information
There are two kinds of touch screens for the PPC-V106 series, one is
resistive touch screens, the other for infrared touch screens.
The resistive touch screen incorporates advanced second-generation
resistive, impact-resistant technology, which allows 75% light transmis-
sion. There is also an antiglare surface for greatly enhanced visual resolu-
tion. It also has new and improved scratch-resistant features.
The resistive touch screen is manufactured from UL-recognized compo-
nents. When properly installed, the touchscreen's ball impact resistance
meets the UL 1950 standard. Its fire resistance meets the UL-746C, 19
mm (0.75") flame test standard. Systems incorporating the touchscreen,
controllers, and cables have been approved to FCC Class A and Class B
standards.
For more detailed information, please visit the following websites:
Advantech Co.,Ltd. reserves the right to alter the touchscreen at any time
without notice.
10.1.2 General specifications
Please refer to Chapter 1, Section 1.2 of this manual.
PPC-V106 User Manual
46
Download from Www.Somanuals.com. All Manuals Search And Download.
10.1.3 Environmental Specifications
Resistive T/S
Infrared T/S
-20 ~ 70° C
-40 ~ 85° C
Operating Temperature
Storage Temperature
-10 ~ 50° C
-40 ~ 71° C
Resistive T/S
90 RH at 35° C
Infrared T/S
0 ~ 95% noncondensing
Relative humidity
Operating
Storage
90 RH at 35° C for 240 0 ~ 95%
hours, non-condensing noncondensing
Chemical resistance: The active area of the resistive touchscreen is resis-
tant to the following chemicals when exposed for a period of one hour at
a temperature of 21° C (71° F):
Acetone, Methylene chloride, Methyl ethyl ketone, Isopropyl alcohol,
Hexane, Ammonia-based glass cleaners, Turpentine, Mineral spirits,
Foods and beverages.
10.2 Installation of Touchscreen Drivers
The touchscreen driver for Windows contains a native, 32-bit driver and a
32-bit control panel program for the PPC-V106 system.
To facilitate installation of the touchscreen driver, you should read the
instructions in this section carefully before you attempt installation.
Important:
The following are examples only. You must fol-
low the instructions and pay attention to the
instructions which then appear on your screen.
Note 1:
The CD-ROM drive is designated as "D"
throughout this chapter.
47
Chapter10
Download from Www.Somanuals.com. All Manuals Search And Download.
10.2.1 Installation of Resistive T/S driver for Windows
98/ME
To install the software to PPC-V106, your PPC-V106 must have Win-
dows 98/Me system running and installed PenMount Series Interface
control board already. If you have an older version of PenMount Win-
dows 98/Me driver installed in your PPC-V106, please remove it first.
1.
2.
You will find out "Unknown Device" when start the system, please
choose "Cancel"
Select from "D:\PPC-V106\Resistive touchScreen\Windows 98-Me
Driver V3.1\setup.exe" to install PenMount windows 98/ME driver
to system
3.
The screen display PenMount logo, copying "installation wizard"
and "PenMount Utilities" screen plus "welcome" message appears.
Selete "Next"
4.
5.
6.
The next screens is "Software License Agreement", select "Yes"
The next screens is "Information", select "Next"
The next screen is "Choose Destination Location". It is for setup
installing PenMount Utilities in the folder: C:\Program Files\Pen-
Mount\Win9x, select "Next" or modify the folder name you like to
use
7.
8.
9.
The next screen is "Select Program Folder", the default is set at
"PenMount Utilities", select "Next" or change it
The next screen is "Start Copying Files", select "Next" for starting
copy files to system
The next screen is "Setup Compelete", select "Finish"
10. The next screen is " Restarting Windows", select "Yes I want to
restart my computer now", and "OK"
PPC-V106 User Manual
48
Download from Www.Somanuals.com. All Manuals Search And Download.
10.2.2 Installation of Resistive T/S driver for Windows
2000/XP
To install the software to PPC-V106, your PPC-V106 must have Win-
dows 2000/XP system running and installed PenMount Series Interface
control board already. If you have an older version of PenMount Win-
dows 2000/XP driver installed in your PPC-V106, please remove it first.
Follow up the steps below to install the PenMount Window 2000/XP
driver.
1.
Select from "D:\PPC-V106\Resistive touchScreen\Windows 2000-
XP Driver V4.01\setup.exe" to install PenMount windows 2000/XP
driver to system
2.
3.
The screen displays copying "installation wizard" and "PenMount
Utilities" screen plus "welcome" message appears. Selete "Next"
The next screens is "Software License Agreement", select "I accept
the terms in the license" and "Next"
4.
5.
6.
The next screens is " Ready to install the Program", select "Install"
The next screen is "Hardware Installation" , select " Continue Anyway"
The next screen is "InstallShield Wizard Completed", Select "Finish"
10.2.3 Installation of Infrared T/S driver for Windows
2000/XP
Select from " D\PPC-V106\Elo IR Touchscreen\Win2K_XP\EloS-
etup.exe" to run the installation application.
10.3 Further Information
ELOtouch: www.elotouch.com
Advantech : www.advantech.com
Salt: www.salt.com.tw
49
Chapter10
Download from Www.Somanuals.com. All Manuals Search And Download.
PPC-V106 User Manual
50
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Programming the
Watchdog Timer
The PPC-V106 is equipped with a
watchdog timer that resets the CPU or
generates an interrupt if processing
comes to a standstill for any reason.
This feature ensures system reliability
in industrial standalone or unmanned
environments.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A Programming the Watchdog Timer
A.1 Programming the Watchdog Timer
To program the watchdog timer, you must write a program which writes I/
O port address 440 (hex). The output data is a time interval value. The
value range is from 01 (hex) to 3F (hex), and the related time interval is
from 1 sec. to 63 sec.
Data Time Interval
01 1 sec.
02 2 sec.
03 3 sec.
04 4 sec.
ï
ï
ï
ï
ï
ï
3F 63 sec.
After data entry, your program must refresh the watchdog timer by rewrit-
ing the I/O port 440 (hex) while simultaneously setting it. When you want
to disable the watchdog timer, your program should read I/O port 440
(hex).
The following example shows how you might program the watchdog
timer :
;-----------------------------------------------------------------------------------
; Enter the extended function mode , interruptible double-write |
;-----------------------------------------------------------------------------------
MOV DX,2EH
MOV AL,87H
OUT DX,AL
OUT DX,AL
PPC-V106 User Manual
52
Download from Www.Somanuals.com. All Manuals Search And Download.
;-----------------------------------------------------------------------------
; Configurate logical device 8, configuration register CRF6 |
;-----------------------------------------------------------------------------
MOV DX,2EH
MOV AL,07H ; point to Logical Device Number Reg.
OUT DX,AL
MOV DX,2FH
MOV AL,08H ; select logical device 8
OUT DX,AL
;
MOV DX,2EH
MOV AL,30H ;Set watch dog activate or inactivate
OUT DX,AL
MOV DX,2FH
MOV AL,01H ; 01:activate 00:inactivate
OUT DX,AL
;
MOV DX,2EH
MOV AL,F5H ; Setting counter unit is second
OUT DX,AL
MOV DX,2FH
MOV AL,00H
OUT DX,AL
;
MOV DX,2EH
MOV AL,F6H
OUT DX,AL
MOV DX,2FH
MOV AL,05H ; Set 5 seconds
OUT DX,AL
53
AppendixA
Download from Www.Somanuals.com. All Manuals Search And Download.
;------------------------------------------
; Exit extended function mode |
;------------------------------------------
MOV DX,2EH
MOV AL,AAH
PPC-V106 User Manual
54
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Pin Assignments
This appendix contains information on
PPC-V106’s pin assignments.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Pin Assignments
B.1 Inverter Power Connector (CN10)
Table B.1: Inverter power connector (CN10)
Pin
Signal
1
2
3
4
5
+12V
GND
1
2
3
4
5
ENAVEE
VBR
+5 V
B.2 Internal Speaker Connector (CN14)
1
2
3
4
Table B.2: Internal speaker connector (CN14)
Pin
Signal
1
2
3
4
Speaker out_L -
Speaker out_L +
Speaker out_R -
Speaker out_R +
PPC-V106 User Manual
56
Download from Www.Somanuals.com. All Manuals Search And Download.
B.3 Floppy Drive Connector (CN16) Reserved
Table B.3: Floppy drive connector (CN16)
Pin
Signal
Pin
Signal
1
2
3
VCC (+5 V)
INDEX
14
15
16
STEP
GND
VCC (+5 V)
WRITE
ENABLE
4
DRIVE
17
GND
SELECT
5
6
VCC (+5 V)
18
19
WRITE DATA
GND
DISK
CHANGE
7
8
9
NC
NC
NC
20
21
22
TRACK 0
GND
WRITE PRO-
TECT
10
11
12
13
MOTOR ON
NC
23
24
25
26
GND
READ DATA
GND
DIRECTION
DENSITY
SELECT
SIDE 1
SELECT
57
AppendixB
Download from Www.Somanuals.com. All Manuals Search And Download.
B.4 IDE Hard Disk Drive Connector (CN15)
Pin
Signal
Pin
Signal
1
IDE RESET #
DATA 7
2
GND
3
4
DATA 8
DATA 9
DATA 10
DATA 11
DATA 12
DATA 13
DATA 14
DATA 15
N/C
5
DATA 6
6
7
DATA 5
8
9
DATA 4
10
12
14
16
18
20
22
24
26
28
30
32
34
36
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
DATA 3
DATA 2
DATA 1
DATA 0
SIGNAL GND
HDD DREQ
IO WRITE
IO READ
HD READY
HDACK 0 #
IRQ14
GND
GND
GND
CABLE SELECT
GND
N/C
ADDR 1
N/C
ADDR 0
ADDR 2
HDD SELECT 1 #
GND
HDD SELECT 0 # 38
IDE ACTIVE 0 #
40
42
44
Vcc
VCC
GND
N/C
# low active
PPC-V106 User Manual
58
Download from Www.Somanuals.com. All Manuals Search And Download.
B.5 IR Connector (CN8) Reserved
1
2
3
4
5
Pin
Signal
1
2
3
4
5
+5V
X
IR_RX
GND
IR_TX
B.6 LVDS Connector (CN4)
Pin Signal
Pin Signal
1
GND
2
GND
N/A
3
LVDS_NO
LVDS_P0
LVDS_N1
LVDS_P1
LVDS_N2
LVDS_P2
LVDS_CN1
LVDS_CP1
VDDSAFE *
4
20
18
19
17
5
6
N/A
7
8
GND
N/A
9
10
12
14
16
18
20
11
13
15
17
19
GND
N/A
GND
N/A
4
2
3
1
VDDSAFE *
* VDDSAFE can
choose +5V or +12V
output via JP2
59
AppendixB
Download from Www.Somanuals.com. All Manuals Search And Download.
B.7 Flat Panel Display Connector (CN2) (Reserved)
Pin Signal
Pin Signal
1
VDDSAFE *
2
VDDSAFE *
3
GND
VDDSAFE *
Vcon
P0
4
GND
VDDSAFE *
GND
P1
40
38
39
37
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
4
2
3
1
GND
SHFCLK
FPDE
ENAVEE
GND
FPVS
FPHS
ENAVEE
* VDDSAFE can
choose +5V or +12V
output via JP2
PPC-V106 User Manual
60
Download from Www.Somanuals.com. All Manuals Search And Download.
B.8 COM1
1 2 3 4 5
6
9
7 8
Pin
Signal
1
2
3
4
5
6
7
8
9
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
RI
B.9 COM2
1 2 3 4 5
6
9
7 8
Pin
Signal
RS-232
DCD
RX
RS-422
TX-
TX+
RX+
RX-
GND
---
RS-485
DATA-
DATA+
---
1
2
3
4
5
6
7
8
9
TX
DTR
GND
DSR
RTS
CTS
RI
---
---
---
---
---
---
---
---
---
61
AppendixB
Download from Www.Somanuals.com. All Manuals Search And Download.
B.14 Parallel Port Connector (CN11)
Table B.4: Parallel Port Connector (CN8)
Pin
Signal
Pin
Signal
1
STROBE*
D1
2
D0
3
4
D2
5
D3
6
D4
7
D5
8
D6
9
D7
10
12
14
16
18
20
22
24
ACK*
PE
11
13
15
17
19
21
23
25
BUSY
SLCT
ERR*
SLCTINI*
GND
GND
GND
GND
AUTOFD*
INIT*
GND
GND
GND
GND
* low active
PPC-V106 User Manual
64
Download from Www.Somanuals.com. All Manuals Search And Download.
PPC-V106 User Manual
66
Download from Www.Somanuals.com. All Manuals Search And Download.
|