Overview
1
Display icons
Earpiece
In call
Standby
Access the main menu.
Display icons
It displays the connection between the handset
Phonebook
The ringer is off.
and the base.The more bars are shown, the
better the signal strength is.
Adjust the volume.
Phonebook
Call log
D205 only:Answering machine: it flashes when
there is a new message. It remains steadily
on when the telephone answering machine is
turned on.
End calls.
It remains steadily on when browsing incoming
calls in the call log.
Loudspeaker
(back side)
Turn the speaker on/off.
Mute/unmute the microphone.
Enter a pause.
Make and receive calls.
Make intercom call.
It indicates an outgoing call in the redial list.
Voice messages indicator: flashes for new
messages, is steady for reviewed messages.
*This is network dependent.
Lock/unlock the keypad.
It flashes when there is a new missed call or
when browsing new missed calls. It remains
steadily on when browsing the missed calls in
call log that are already read.
Make and receive calls through the speaker.
Loudspeaker
(back side)
In menu
Microphone
D205
It displays when you scroll up/down a list or
increase and decrease the volume.
Confirm / Enter the option menu. /Select
In text input
D200
Find
handset
Cancel
It flashes when receiving incoming call. It remains
steadily on during a call.
There are more digits on the right. Press
read.
to
Delete text
Up / down
Enter a space.
The speaker is on.
ECO+
The ECO+ mode is activated.
/
/
Exit menu.
Switch upper/lower case.
Find
handset
Connect
2
1
2
3
Multi-handset version
only.
Get started
3
Insert batteries
Charge your phone
Configure your phone
1 When using your phone for the first time, you see a
welcome message (country dependent).
2 Set the country and language if prompted.
3 Set the date and time.
Charge 8 hours
> 70%
10% - 40%
< 10%
• If the time is in 12-hour format, press
/
to select
[am] or [pm] (country dependent).
40% - 70%
Flashing: low battery
Scrolling: charging in progress
Enjoy
4
Phonebook
Call log
Record an announcement
(for D205 only)
Restore default settings
Add record
Call from the call log
You can reset your phone settings to the original
factory settings.
1 Press
.
1 Press
.
1 Press
.
1 Press
.
2 Select [Phonebook] > [Add new].
3 Follow on-screen instructions.
2 Select a record and press
.
2 Select [Answ. Machine] > [Announcement].
3 Follow on-screen instructions.
2 Select [Services] > [Reset], then press
confirm.
3 Follow on-screen instructions.
to
Save record
Call from the phonebook
1 Press
>
> [Save number].
Register additional handsets
1 Press
.
2 Follow on-screen instructions.
You can register additional handsets to the base
station.
2 Select a record and press
.
Delete record
Note
Direct access memory
1 Press
>
> [Delete].
1 Press
.
• You may recall the original PIN/passcode by
following this procedure.
You have 2 direct access memories (Keys 1 and 2).
To dial the saved phone number automatically, press
and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to [1_voicemail] (voice mail number) and
[2_info svc] (information service number) of your
network operator respectively (network dependent).
2 Follow on-screen instructions.
2 Select [Services] > [Register], then press
to confirm.
3 Press and hold on the base station for 5
seconds.
4 Enter the system PIN/passcode (0000).
Redial list
Call from the redial list
1 Press
2 Select a record and press
.
5 Press
to confirm the PIN/passcode.
.
»
Registration is complete in less than 2 minutes.
Save record
1 Press
>
> [Save number].
2 Follow on-screen instructions.
Delete record
1 Press
>
> [Delete].
2 Follow on-screen instructions.
Technical data
Battery
• Philips: 2 x AAA NiMH 1.2V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Adapter
Base and charger:
Philips:
Input:
MN-A102-U130
100-240V~
S003IB0600040
100-240V~
50/60 Hz 0.2 A
Output: 6V 400 mA
50/60 Hz 0.15 A
6V 400 mA
Phonebook with 50 entries
Call log with 20 entries
Talk time: 16 hours
Standby time: 180 hours
Note
• You can install a DSL (digital subscriber line) filter to
prevent noise and caller ID problems caused by the
DSL interference.
• You can find the Declaration of Conformity on
Frequently asked questions
No signal bar is displayed on the screen.
I have chosen a wrong language which I cannot
read, what do I do?
No display
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
• The phone is at a location with thick walls. Move
the base away from them.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays [Unregistered], register
your handset. (See the section on “Register
additional handsets”).
• Make sure the batteries are charged.
• Make sure there are power and phone
connections.
1 Press
2 Press
to go back to the standby screen.
to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages] > [Langue]
[Config. tel.] > [Sprache]
[Config. telef.] > [Lingua]
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger.The battery icon animates when charging.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the
power supply first and clean the contacts with a
damp cloth.
If I fail to pair (register) the additional handsets to
the base station, what do I do?
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.
Your base memory is full.Access
> [Services]
4 Select it to access the language options.
5 Select your own language.
> [Unregister] to unregister the unused handsets
and try again.
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Batteries are defective. Purchase new ones with
the same specifications.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
0168
When this crossed-out wheeled bin symbol
is attached to a product it means that the
product is covered by the European Directive
2002/96/EC.
2013 © WOOX Innovations Limited.
All rights reserved.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.
UMS_D200-205
05_EN_V2.0
WK13382
|