Philips Professional
&
Business Solutions
EN
User Manual
TYPE Nr.
BDH5031V.00
User Manual BDH5031V
When unplugging your Monitor, always grip the plug firmly and
pull straight out from the socket.
• It can result in fire or electric shock due to damaged power cord.
When moving your Monitor, remove the power plug, and cables,
and be sure to move it by using two people.
• Failure to follow this instruction can result in electric shock or per-
sonal injury.
Do not touch the power plug with wet hands when plugging or
unplugging it into the wall socket.
• It can result in a risk of electric shock.
1.2 INSTALLATION
Do not place this Monitor on an unstable cart, stand, or table.
• It may cause the product and cart to overturn, damaging equipment
or causing possible injury.
Do not use this product in the neighbourhood of a bath or show-
er.
• It can result in electric shock or fire.
Please place the Monitor set in such a way that the main plug can
be easily disconnected.
User Manual BDH5031V
Do not install the product where there is oil, smog, moist, or dust.
• It may cause malfunction.
Do not install the product where it will be exposed to the direct
sunlight, and the product should not be near heat sources such
as radiators, stoves, etc.
• It may cause malfunction.
For proper ventilation, separate the product from the wall, and
keep a distance of more than 10 cm (4 inches).
• Due to the increase of temperature inside the Monitor, it may cause fire.
Minimum distances around the apparatus for sufficient ventilation.
Due to the increase of temperature inside the Monitor, it may cause a fire.
If you wish to install this product on the wall or ceiling, refer to a
professional.
• Failure to do so may cause damage to product and injury to human.
User Manual BDH5031V
1.3 DURING USE
Do not open the cover (or back) because high voltage is present
within the Monitor enclosure.
• It may cause electric shock.
Never push any kind of objects into this product through open-
ings at the back of Monitor.
• It may cause fire or electric shock.
The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed
on the apparatus.
• Spilled liquids may cause electric shock or fire.
Do not allow children to play or hang on the Monitor.
• These actions may tip it over, causing personal injury.
Do not place a candle or lighted cigarette on the Monitor.
• If these fall into the inside of the Monitor, it may cause a fire or ex-
plosion.
User Manual BDH5031V
Do not disassemble batteries, and do not leave around in case
children swallow them.
• Heavy metal may contaminate environment, and can be harmful or
detrimental to human health. (If children swallow the batteries, go
to hospital and consult with a doctor.) Batteries could explode if fit-
ted incorrectly. Align the batteries according to the (+) and (-) indica-
tion inside the case.
Do not spray water onto the Monitor or wipe with damp cloth.
• It may cause an electric shock or fire.
Unplug the Monitor from the wall outlet when smoke or a
strange smell occurs, then refer to a service personnel.
• Leaving the Monitor on in this condition, may cause fire or electric
shock.
The plasma display panel consists of fine cells. Although the pan-
els are produced with more than 99.9 percent active cells, there
may be some cells that do not produce light or remain lit.
Do not allow a still picture to be displayed for an extended pe-
riod, as this can cause a permanent ghost image to remain on the
Plasma Display.
• Examples of still pictures include logos, video games, computer im-
ages, teletext and images displayed in 4:3 mode. The warranty does
not cover any damage caused by image retention.
Do not wipe the Monitor using a cloth damped with chemicals
(benzene, thinners, etc.).
• The Monitor appearance may be marred.
(Unplug the power plug and wipe with soft cloth.)
User Manual BDH5031V
Do not place heavy objects or heat sources on the power cord.
• It may damage the power cord, causing fire or electric shock.
Do not place any object or cover on the Monitor.
• In an event of improper ventilation, the Monitor will be overheated
causing fire.
When watching the Monitor, the distance between the Monitor
screen and your eye should be 5~7 times the diagonal size of the
Monitor.
• Watching the Monitor for a long time may hurt your eye sight.
When cleaning of the inside of the Monitor is required, consult a
qualified service personnel.
• When the Monitor is not cleaned for a long period of time, dust in it
may cause fire or malfunction.
When the Monitor is placed on a cart or table, the front side of
the Monitor should not project outward.
• Unbalance may cause the Monitor to drop, resulting in personal
injury or equipment malfunction and damage.
User Manual BDH5031V
2. CHECKING ACCESSORIES
2.1 SUPPLIED ACCESSORIES
Check to be sure that the following items are packed with your Plas-
ma panel.
1. Remote Control
2. Batteries
3. EDFU
4. VGA Cable
5. Ferrite Core
6. AC Power Cable
(UK, Europe)
1 UNIT
2 UNIT
1 UNIT
1 UNIT
1 UNIT
2 UNITS
P.MODE PICTURE FMT
AV
S.MODE
PIP
S.EFFECT PIXEL SHIFT
POSITION COLOR TEMP
PIP SOURCE
SWAP
RECALL
MENU
VOL
VOL
TIMER
STILL
MUTE
R-48F01
Remote Control
Batteries
EDFU
VGA Cable
Ferrite Core
Power Cable Europe
Power Cable UK
User Manual BDH5031V
CONTENTS
User Manual BDH5031V
3. PANEL CONTROLS
1
2
3.1 FRONT PANEL
* Items having the same name on the plasma display and the remote
control would function in exactly the same way.
1. Power control sensor
2. Power Stand by:
Red : Stand by
Green : ON
User Manual BDH5031V
DIGITAL
AUDIO
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
OPTICAL
VIDEO
AUDIO
AUDIO
SERVICE
MENU
MOVE
MENU
MOVE
2
3
4
5
6
1
DIGITAL
AUDIO
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
OPTICAL
VIDEO
AUDIO
AUDIO
SERVICE
14
7
8
9
10
11
12
13
3.2 REAR PANEL
1. Power cord input
2. AV button
7. HDMI INPUT
8. PC AUDIO INPUT
3. Menu button
Use this button to enter and exit the MENU.
4. Volume UP/DOWN buttons
9. PC INPUT (15 pin D-sub)
10. PC OUTPUT (15 pin D-sub)
11. COMPONENT A/V jacks
Use these buttons to change your TV’s volume or to 12. SCART, A/V INPUT/OUTPUT
move the cursor in the menu.
5. Move Buttons
13. External Speaker
14. AV3 INPUT
Use these buttons to navigate through the the On
Screen Display menu.
6. Main Power button
Use this button to switch TV to Stand By mode or TV
ON mode.
User Manual BDH5031V
4. REMOTE CONTROL
Note:
• Use two “AAA” batteries.
• Be sure to use replacement batteries of the same type as the original ones.
• The life of a battery depends on how much it has been used.
4.1 REMOTE CONTROL
Power button - while the AC power cord is connected, turn the dis-
play ON (Green light) or OFF (red light stand-by).
P.MODE PICTURE FMT
AV
P.MODE button - Whenever pressing the button, it cycles in the follow-
ing order. Normal Dynamic Cinema User
S.MODE
PIP
S.EFFECT PIXEL SHIFT
POSITION COLOR TEMP
PICTURE FMT button - Adjusts the size of the screen (Normal, 16:9,
etc).
AV button - Use this function to make video input selection. It changes
in the following sequence: AV 1 AV 2 AV 3 Component PC
HDMI.
PIP SOURCE
SWAP
RECALL
S.MODE button - Whenever pressing the button, it cycles in the follow-
ing order: Normal Movie Music News User.
MENU
VOL
S.EFFECT button - Press to use a spatial sound effect.
VOL
PIXEL SHIFT button - The whole screen shifts up/down, left/right at 25
sec interval to minimize image sticking.
PIP; POSITION; PIP SOURCE; SWAP - PIP buttons.
COLOR TEMP button - Change the colour mood of the panel.
RECALL button - Indicates the current state and resolution.
Menu button - Used to display a desired menu.
Volume buttons “ / ”
TIMER
STILL
MUTE
Timer button - Each time you press this button, a different input mode
appears. The sequence is as follows: 15Min. 30Min. 60Min.
90Min. 120Min. OFF
R-48F01
After the time is selected, it automatically becomes stand-by state.
STILL button - Press this button to freeze the picture.
Mute button - Mute sound.
User Manual BDH5031V
4.2 INSTALLING THE BATTERIES IN YOUR REMOTE CONTROL
1. Open the battery compartment on the back of the remote control.
2. Install two AAA-size batteries (not included) as shown. Make sure the
“+”and “-”terminals are oriented correctly.
3. Replace the cover.
4.3 WHEN USING REMOTE CONTROL
• Be sure not to allow the remote control to drop or to become wet.
• Keep it away from hot or moist locations.
User Manual BDH5031V
5. CONNECTING WITH AN EXTERNAL SOURCE
5.1 WATCHING DIGITAL BROADCASTS
• To watch digital broadcasts:
- Purchase a separate Digital Broadcasting Receiver (SET-TOP BOX).
- Connect the PDP to a Digital Broadcasting Receiver as shown left.
D
I
G
I
T
A
L
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
AU
D
I
O
A
O
P
T
I
C
L
VIDEO
AUDIO
AUDIO
SERVICE
MENU
MOVE
DIGITAL
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
AUDIO
PC OUT
OPTICAL
VIDEO
AUDIO
AUDIO
SERVICE
Component
Video
Audio
1. Connect a Digital Broadcasting Receiver to the PDP.
• Prepare A/V cables.
• Connect the cables from the digital TV Receiver output terminal to the
PDP (Component ) input terminal.
• When connecting the cables, be sure to match the cable colours.
2. Press the Power Buttons.
• Turn the PDP and the receiver ON.
3. Input Select.
• Select [Component] by pressing the “AV”button of the remote control
or using the button of the PDP unit.
Digital Broadcasting
Receiver
• When you press the “AV”button, you will see the OSD as shown. You
can move using “/“ and select desire input mode with “/“ but-
ton.
(Set-Top Box)
AV 1
Picture
Sound
Screen
Feature
Input
AV 2
AV 3
4. Select the Desired Channel and Function.
• Select the desired channel and function by using the remote control
of the Digital Broadcasting Receiver.
Component
PC
HDMI
Notes:
1) Possible digital broadcasting signals: 1080i, 720p, 576p, 576i, 480p, 480i.
2) What is a component? : Signals with which luminance and chrominance
are separated, producing a sharp picture.
3) If the Digital Broadcasting Receiver has PC output terminal or HDMI
output terminal, connect to ‘PC INPUT’ or ‘HDMI INPUT’ at the rear of the
panel of the PDP.
Move
Select
Exit
User Manual BDH5031V
5.2 WATCHING CABLE BROADCASTS
• To watch cable broadcasts, subscribe to your local cable TV broadcast-
ing, and then connect a cable Broadcasting Receiver to the PDP as
shown left.
1. Connect a Cable Broadcasting Receiver to the PDP.
• Prepare the A/V cable.
D
I
G
I
T
A
L
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
AU
D
I
O
A
O
P
T
I
C
L
VIDEO
AUDIO
AUDIO
SERVICE
• Connect the receiver (Output) to PDP (Video Input) as shown below.
MENU
MOVE
• N.B. : If both S-Video and Video/Audio (RCA) cables are connected to-
gether in AV3 input, S-Video always takes precedence. However, the left
and right audio leads should be connected for the sound even though you
would like to use S-Video as AV3 input.
2. Press the Power Buttons.
• Turn the PDP and the receiver ON.
3. Input Select.
• Select [AV 1 (Scart), AV 2 (Scart) or AV3 (S-Video)] by pressing the “AV”
button of the remote control or the in keypad of the PDP unit.
• When you press the “AV”button, you will see the OSD as shown. You
can move using “/“ and select desire input mode with “/“ but-
ton.
Video/Audio
4. Select the Desired Program and Function.
• Select the desired program and function by using the remote control
of the Cable Broadcasting Receiver.
S-Video
Video/
Audio
Notes:
1) If your local cable company re-transmits digital broadcasts, you may
watch normal broadcasts and digital broadcasts simultaneously. For
detailed information, refer to your local cable company.
2) Only AV1 provides ‘Monitor Out’ function.
3) AV1 full scart (RGB/CVBS).
4) AV2 half scart (CVBS).
Cable Broadcasting
Receiver
AV 1
Picture
Sound
Screen
Feature
Input
AV 2
AV 3
Component
PC
HDMI
Move
Select
Exit
User Manual BDH5031V
5.3 WATCHING SATELLITE BROADCASTS
• To watch satellite broadcasting, subscribe to Digital Satellite Broad-
casting, then connect the satellite Broadcasting Receiver to the PDP as
shown left.
D
I
G
I
T
A
L
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
AU
D
I
O
A
O
P
T
I
C
L
VIDEO
1. Connect a Satellite Broadcasting Receiver to the PDP.
• Prepare the A/V cable.
AUDIO
AUDIO
SERVICE
MENU
MOVE
• Connect the receiver (Output) to PDP (Video Input) as shown left.
• When connecting to an external AV source, be sure to match the col-
ours.
• N.B. : If both S-Video and Video/Audio (RCA) cables are connected to-
gether in AV3 input, S-Video always takes precedence. However, the left
and right audio leads should be connected for the sound even though you
would like to use S-Video as AV3 input.
2. Press the Power Buttons.
• Turn the PDP and the Satellite receiver ON.
3. Input Select.
• Select [AV 1 (Scart), AV 2 (Scart) or AV3 (S-Video)] by pressing the [AV]
button of the remote control or the in keypad of the PDP unit.
• When you press the “AV”button, you will see the OSD as shown. You
can move using “/“ and select desire input mode with “/“ but-
ton.
Video/Audio
S-Video
4. Select the Desired Program and Function.
• Select the desired program and function by using the Remote Control
of the Satellite Broadcasting Receiver.
Video/
Audio
Satellite Broadcasting
Receiver
AV 1
Picture
Sound
Screen
Feature
Input
AV 2
AV 3
Component
PC
HDMI
Move
Select
Exit
User Manual BDH5031V
5.4 WATCHING A DVD IMAGE
• Component Input is set to 480i/576i and 480p/576p mode.
• Connect the cable from the DVD Video output (Y, Pb/Cb, Pr/Cr) to the
Component Input at the back of PDP, and connect the cable from DVD
audio output (Left, Right) to the Audio Input at the back of PDP.
D
I
G
I
T
A
L
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
AU
D
I
O
A
O
P
T
I
C
L
VIDEO
AUDIO
AUDIO
SERVICE
1. Connect a DVD Player to the PDP.
MENU
MOVE
• Prepare the AV cable.
• Connect the DVD (Output) to the PDP (Component or Video Input) as
shown below.
• When connecting to an external AV source, be sure to match the col-
ours.
• N.B. : Video input can be via scart cable, S-Video, or Yellow phone. The red
and white plugs are for left and right audio to accompany the yellow video
lead or to be used with the S-Video lead to produce sound.
2. Press the Power Buttons.
• Turn the PDP and the DVD ON.
3. Input Select.
• Select [Component, AV1 (Scart), AV2 (Scart) or AV3 (S-Video)] by press-
ing the [AV] button of the remote control or the in keypad of the PDP
unit.
• When you press the “AV”button, you will see the OSD as shown. You
can move using “/“ and select desire input mode with “/“ but-
ton.
S-Video
Component
Video
Audio
Video/
Audio
Video/
Audio
DVD
DVD
DVD
4. Select the Desired Title and Function.
• Select the desired title and function by using the remote control of the
DVD.
AV 1
AV 2
AV 3
Picture
Notes:
Component
PC
Sound
Screen
Feature
Input
1) Y/Cb/Cr, which stands for component video DVD player’s output can also
be written as Y/B-Y/R-Y, Y/Pb/Pr depending on the kinds of DVD model.
2) The way of connecting the DVD to the PDP is as follows:
Y Y, Cb Pb, B-Y, Cr Pr, R-Y
3) The DVD output can be Video, S-Video or Component Video depending
on the DVD model. There are various output modes, so be sure to check
when you purchase it.
HDMI
Move
Select
Exit
4) When connecting S-Video and Video simultaneously, only S-Video will be
displayed on the screen as it takes precedence.
User Manual BDH5031V
5.5 WATCHING A VCR IMAGE
• Video can use either the video terminal or the S-video terminal.
1. Connect a VCR to the PDP.
• Prepare the AV cable.
D
I
G
I
T
A
L
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
AU
D
I
O
A
O
P
T
I
C
L
VIDEO
• Connect the Video (Output) to PDP (Video Input) as shown left.
AUDIO
AUDIO
SERVICE
MENU
MOVE
2. Press the Power Buttons.
• Turn the PDP and the VCR ON.
3. Input Select.
• Select [AV 1 (Scart), AV 2 (Scart) or AV 3 (S-Video)] by pressing the [AV]
button of the remote control or the in keypad of the PDP unit.
• When you press the “AV”button, you will see the OSD as shown. You
can move using “/“ and select desire input mode with “/“ but-
ton.
4. Select the Desired Title and Function.
• Select the desired title and function by using the remote control of the
VCR.
Notes:
Video/
Audio
1) When connecting a VCR, the S-Video terminal provides a better image
than the Video terminal.
2) When connecting to the Video terminal, connect 3 colour AV cables
(video, left audio, right audio) to the PDP; for the S-Video terminal, con-
nect the Audio terminal (Left, Right) in the same way, and connect the
S-Video cable (sold separately).
S-Video
Video/
Audio
3) When connecting the Video terminal and the S-Video simultaneously,
the S-Video terminal is selected. This can be checked by the [Recall] but-
ton of the remote control.
VCR
AV 1
Picture
Sound
Screen
Feature
Input
AV 2
AV 3
Component
PC
HDMI
Move
Select
Exit
User Manual BDH5031V
5.6 WATCHING A CAMCORDER/GAME CONSOLE IMAGE
• Enjoy images recorded by camcorder or the game console after con-
necting to the PDP.
1. Connect a Camcorder/Game Console to the PDP.
• Prepare the AV cable.
D
I
G
I
T
A
L
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
AU
D
I
O
A
O
P
T
I
C
L
VIDEO
AUDIO
AUDIO
SERVICE
• Connect the Video (Output) to the PDP (Video Input) as shown below.
• When connecting to an external AV source, be sure to match the col-
ours.
MENU
MOVE
2. Press the Power Buttons.
• Turn the PDP and the Camcorder/Game Console ON.
3. Input Select.
• Select [AV 1 (Scart), AV 2 (Scart) or AV 3] by pressing the [AV] button of
the Remote Control or the in keypad of the PDP unit.
• When you press the “AV”button, you will see the OSD as shown. You
can move using “/”and select desire input mode with “/”but-
ton.
Video/
Audio
4. Select Function.
• Select the function by using the remote control of camcorder or game
console.
S-Video
Video/
Audio
Notes:
1) When connecting the device, the S-Video terminal provides a better im-
age than the Video terminal.
2) When connecting to the Video terminal, connect 3 colour AV cables
(video, left audio, right audio) to the PDP; for the S-Video terminal, con-
nect the Audio terminal (Left, Right) in the same way, and connect the
S-Video cable (sold separately).
Game Console/Camcorder
AV 1
Picture
Sound
Screen
Feature
Input
AV 2
AV 3
Component
PC
HDMI
Move
Select
Exit
User Manual BDH5031V
5.7 CONNECTING PC (15 PIN D-SUB)
• This product supports resolutions of VGA, SVGA, XGA, WXGA, SXGA.
• Before connecting a PC to the PDP, be sure to adjust the resolution of
the PC.
1. Before Connecting to the PDP, Set the Resolution of the PC.
• Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen
of the PC.
• Choose the SETTINGS tab in the DISPLAY menu.
• In the SETTINGS menu, select 640 x 480, 800 x 600, 1024 x 768 or 1280
x 1024
2. Connect the PC to the PDP.
• Prepare the PC cable (D-sub 15 pin) and the PC audio cable.
• Connect the PC (Output) to the PDP (Input) as shown below.
• If using the audio cable for connection, put the ferrite core to the mid-
dle of the cable for preventing EMI.
D
I
G
I
T
A
L
D
I
G
I
T
A
L
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
COMPONENT
INPUT
PC OUT
AU
D
I
O
A
PC OUT
AU
D
I
O
A
O
P
T
I
C
L
O
P
T
I
C
L
VIDEO
VIDEO
AUDIO
AUDIO
AUDIO
AUDIO
SERVICE
SERVICE
MENU
MOVE
MENU
MOVE
Audio
15 PIN
D-sub
Output connect
Ferrite Core
User Manual BDH5031V
3. Press the Power Buttons.
• Turn on the PDP and the PC.
4. Input Select.
AV 1
• Select [PC] by pressing the AV button of the remote control or PDP
unit.
• When you press the “AV”button, you will see the OSD as shown. You
can move using “/”and select desire input mode with “/”but-
ton.
Picture
Sound
Screen
Feature
Input
AV 2
AV 3
Component
PC
HDMI
• N.B. : You cannot select PC if the picture in picture mode is on.
5. Enjoy Dynamic Ultra Screen Monitor by Using PC’s Keyboard or
Mouse.
Move
Select
Exit
Notes:
1) The resolution of the PC monitor is the best at 800 x 600 (SVGA) for SD
panel and at 1024 x 768 (XGA) for HD panel.
2) If there is a [Vertical Frequency] setting menu in the [Display] menu of
the PC, adjust the frequency to 60Hz.
3) If the PC resolution is too high, it may be hard to read letters.
Select a suitable resolution.
4) If the picture don’t fit with the size or position of the screen, select the
[Auto] function in the Screen Menu in order to make fit automatically.
Also, you can adjust the position of the picture with [H.position] and
[V.position] functions manually.
5) If the picture quality is not clear, select [Auto] function in the Screen OSD
menu. It will find the best quality by itself. If you are still unsatisfied in the
picture quality, please adjust [Phase] and [Frequency].
User Manual BDH5031V
5.8 CONNECTING HDMI
• This product supports resolution of VGA, SVGA, XGA, SXGA.
• Before connecting a PC to the PDP, be sure to adjust the resolution of PC.
• This product is supported by Plug and Play only at HDMI.
• This Plasma unit is compliant with HDMI 1.1 version.
D
I
G
I
T
A
L
INPUT
HDMI PC AUDIO PC IN
AV1
AV2
COMPONENT
INPUT
PC OUT
AU
D
I
O
A
O
P
T
I
C
L
VIDEO
AUDIO
AUDIO
SERVICE
1. Connect the HDMI to the PDP.
MENU
MOVE
• Prepare the HDMI cable.
• Connect the HDMI (Output) to the PDP (Input) as shown left.
2. Press the Power Buttons.
• Turn on the PDP and DVD or Game console.
3. Input Select.
• Select [HDMI] by pressing the AV button of the remote control or the
button on the PDP unit.
• When you press the “AV”button, you will see the OSD as shown. You
can move using “/”and select desire input mode with “/”but-
ton.
Notes:
HDMI input port receives only digital signal.
HDMI
Game Console
DVD
PC and HDMI Input Resolution Available in PDP
• Depending on graphic card, problems like no signal detected or line
noises can happen. If these problems happen, contact the graphic
card company for help.
AV 1
AV 2
AV 3
Picture
Sound
Screen
Feature
Input
Resolution
H Freq. (KHz)
31.469
V Freq. (Hz)
59.940
Remark
DOS
HDMI
PC
o
Component
PC
o
o
o
o
o
o
o
o
640 x 480
37.861
72.809
VESA
VESA
IBM
o
HDMI
37.500
75.000
o
720 x 400
800 x 600
31.469
70.087
o
35.156
56.250
VESA
VESA
VESA
VESA
o
37.879
60.317
o
1024 x 768
48.363
60.004
o
Move
Select
Exit
1280 x 1024
63.981
60.020
o
User Manual BDH5031V
5.9 CONNECT WITH THE DOLBY DIGITAL AMP.
If you connect the optical output to a Dolby digital AMP, you can listen
to better sound.
DIGITAL
INPUT
PC AUDIO
AV1
AV2
COMPONENT
INPUT
AUDIO
PC OUT
HDMI
PC IN
OPTICAL
VIDEO
AUDIO
AUDIO
SERVICE
Optical output
I
N
P
U
T
Dolby Digital AMP
Woofer
L
Center
R
Surround L
Surround R
User Manual BDH5031V
6. PICTURE
6.1 SELECTING PICTURE MODE
• Select the Picture mode that is appropriate depending on the kinds of
pictures, you enjoy.
P.MODE
1. Selecting Picture Mode.
• Press the “P.MODE”on the remote control.
• While pressing the “P.MODE”for the first time, the current picture
mode will be displayed.
2. Each Press of the Button Will Select One of Four Picture Modes.
• Each time you press the button, a different picture mode appears. The
sequence used is as follows:
Normal Dynamic Cinema User
* Normal: For a highly defined image in a normally bright room
* Dynamic: For a clear-cut image emphasizing high contrast for sports
viewing.
* Cinema: For a movie
* User: Allows the user to customise settings as desired.
3. Menu on the Screen will disappear.
• After selecting a desired picture mode, the menu on the screen will be
disappeared.
• If you want to customise the picture mode, refer to the following page.
Notes:
1) Normal, Dynamic, and Cinema modes are factory preset values.
2) When adjusting sub-menus while you are in Normal, Dynamic, and
Cinema modes, the Picture Mode will be automatically converted to User
Mode, and the adjustments will be made.
3) Selecting [Mode Reset] in the [Feature], menu will allow the Brightness,
Contrast, etc. to return to the factory preset values.
User Manual BDH5031V
6.2 CUSTOMIZING PICTURE
• You can adjust the colour tone and brightness to your preference.
1. Press the MENU Button.
Mode
Dynamic
• The MENU shown below will display on the screen.
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Select
Exit
2. Press the / button.
Mode
Dynamic
• After selecting [Picture] by the “/”buttons, press
the “”button. Then the sub menu of [Picture] will be
displayed.
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Adjust
Exit
3. Select the User Mode.
Mode
User
• Select [User] by the “/”buttons in the [Mode].
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Adjust
Exit
User Manual BDH5031V
4. Select User Mode Adjustments.
• While you are in [Picture Mode – User], press the
“/”buttons to select a specific adjustment item.
MENU
VOL
Mode
User
VOL
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Adjust
Exit
5. Picture Condition Adjustments.
• Press the “/”buttons to adjust the picture of your
preference.
Mode
User
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
50
50
8
• Noise Reduc. functions the noise reduction.
Sharpness
Colour
50
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Adjust
Exit
6. Press the “COLOR TEMP” button on the remote con-
trol.
• Pressing the “COLOR TEMP”button first time will display
the current setting for COLOR TEMP.
• Each time you press the button, a different colour temp appears.
The sequence used is as follows :
COLORTEMP
Mode
User
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
50
50
8
Sharpness
Colour
50
Colour Temp.
Noise Reduc.
Normal
On
Normal Warm Cool
Notes:
1) While you are in the PC or HDMI input mode, you can only adjust bright-
ness, contrast and colour temperature.
MENU
Move
Adjust
Exit
2) When you adjust Brightness, Contrast, and Colour in DTV mode or adjust
Brightness and Contrast in PC and HDMI mode, the picture is adjusted
finely.
3) The Tint control is used when the input signal is NTSC or Component. If
input signal is NTSC, Tint control is displayed in picture menu.
4) Selecting the colour temperature makes the mood : normal, warm or
cool.
User Manual BDH5031V
6.3 ADJUSTING SCREEN
• You can adjust screen size or aspect ratio a desired.
6.3.1 Adjusting with PICTURE FMT button
1. Press the PICTURE FMT Button.
• The current screen size will be displayed on the screen.
• Each time you press the PICTURE FMT button on the remote control, a
different screen size appears. The sequence used is as follows in case
of AV1, AV2 and AV3 modes :
PICTURE FMT
Auto 16:9 4:3 LB(16:9) LBS(16:9) 14:9 LB(14:9)
LBS(14:9) Auto
• N.B. : You cannot select screen size if the picture in picture mode is on.
Notes:
1) Displaying a picture in a 4:3 mode for a long time may cause phosphor
of the PDP to be burned. So avoid displaying a picture in 4:3 screen size
for a long time.
2) Under PC and HDMI inputs, only 16:9 and 4:3 are available.
3) Auto : Displays pictures of original picture size.
16:9 : 16:9 picture formats;
14:9 : 14:9 picture formats;
4:3 : 4:3 picture formats like an analog TV;
LB : Enlarges the screen as to fill the black part above and below the
picture;
LBS : Enlarges the screen, and shifts up as to see the subtitles in case you
are watching video with subtitles.
4) If the picture shows unclear image in the 480P component input source,
try to toggle the resolution from the DTV/DVD of the Screen Mode.
User Manual BDH5031V
6.3.2 Adjusting Screen in the MENU
• You can adjust the screen in the menu.
• This function is same to the [PICTURE FMT] of remote controller.
1. Press the MENU Button.
Mode
Dynamic
• The MENU screen as shown below will appear.
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Select
Exit
MENU
2. Press the “/” button.
VOL
VOL
Mode
16:9
• Press the “/”buttons to select “Screen”.
Picture
Sound
Screen
Feature
Input
H. position
V. position
Phase
91
50
32
50
Frequency
Auto
3. Press the Volume “/” buttons.
• Press the Volume “/”buttons to enter the sub menu MENU
VOL
VOL
DTV/DVD
640x480
“Screen”.
• While you are in “Screen”menu, press the “”or “”
button to select a desired item, and then, adjust the
value by pressing the “”or “”.
MENU
Move
Select
Exit
< In case of PC input >
Notes:
1) Screen Mode is different according to the input modes.
Input
Available Screen Mode
AV
16:9, 4:3, LB(16:9), LBS(16:9)
14:9, LB(14:9), LBS(14:9), Auto
Component
PC, HDMI
16:9, 4:3, LB(16:9), LBS(16:9)
14:9, LB(14:9), LBS(14:9)
16:9, 4:3
2) Other Screen adjustments
< Under PC mode >
[H. Position] : As the value increases, the screen moves to the right.
[V. Position] : As the value increases, the screen moves up.
[Phase] : Adjust phase.
[Frequency] : Adjust frequency.
[Auto] : Adjusting automatically the screen to optimum states.
< Under PIP mode >
[Alpha Blend] : Adjusting the translucent rate of the subpicture.
User Manual BDH5031V
6.4 WATCHING A STILL IMAGE
• You can view still images with this function. However, displaying the
same images such as still images for a long time may cause image
burn.
1. Press the “STILL” button.
STILL
• If you wish to freeze a picture, press the “STILL”button.
You can still hear the sound.
• Press “STILL”button again to cancel the “STILL”function.
Notes:
Still
1) Displaying the same images such as still images for a long time may
cause image burn (after-image lagging).
2) In this case, such “image burn” may become less noticeable if moving
images are later displayed for a long time.
3) However, an image burn may become a permanent one, damaging the
Plasma Display; therefore, avoid displaying the same images for a long
time.
4) Use the function [Anti Burn-in], while displaying still images for a long
period of time to minimize this effect. Anti Burn-in (on or off) is in the
Feature menu.
User Manual BDH5031V
6.5 WATCHING TWO PICTURES SIMULTANEOUSLY
• PIP (Picture-in-Picture) and P-by-P (Picture-by-Picture) modes allow
users to watch two pictures simultaneously.
Screen Adjustment of the Sub-picture
• Alpha Blend of the sub-picture can be adjusted on Screen Menu of
OSD.
PIP
POSITION C
• Alpha Blend is only available in PIP mode.
PIP SOURCE
SWAP
Alpha Blend - The adjustment of alpha blend allows the subpicture to
be translucent. The translucent rate is controlled with “/”buttons.
1. Engaging PIP mode.
• Press the ‘PIP’button once on the remote control to engage the Pic-
ture-in-Picture mode.
• By pressing the button repeatedly, it will show the following cycle.
• If switched to P-by-P (Picture-by-Picture) mode, the screen will be split
in half. The screen on the left side is the main picture, and the sub-pic-
ture will be on the right of the screen.
PIP
P by P
Main
Main
Main
Sub
Sub
<Using ‘Position’button>
2. Position of the Sub-picture.
Main
Main
• When PIP mode is engaged, the sub-picture can be displayed in one
of the four corners by using‚POSITION’button.
• Whenever pressing the button, the sub-picture will be cycling in the
following order.
• If you would like to move the sub-picture to specific position you de-
sire, use navigation keys.
Sub
Sub
Sub
Sub
Main
Main
<Using “/”and “/”button>
Sub
3. Swap the pictures.
• In order to swap between the main picture and sub-picture, press the
‘SWAP’button.
User Manual BDH5031V
4. Select the Input Source.
• Various signal sources can be displayed within the sub-picture under
PIP mode.
PIPSOURCE
• Once the PIP mode is on, you may change the input source of the sub-
picture by pressing the “SOURCE”button.
• Pressing the “SOURCE”button repeatedly will cycle through following
order:
AV1 AV2 AV3
5. Available PIP Input Combinations.
• Main-picture and sub-picture input combinations are listed below for
reference.
Main
AV1
(CVBS)
AV2
(CVBS)
AV3
(CVBS/S)
AV1
(RGB)
COMP
PC
X
HDMI
PIP
AV1
(CVBS)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
AV2
(CVBS)
X
AV3
(CVBS/S)
X
AV1
(RGB)
X
COMP
PC
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
HDMI
User Manual BDH5031V
7. SOUND
7.1 SELECTING SOUND MODE
• Enjoy various sound modes by selecting your favourite Sound Mode
depending on the kinds of moving pictures.
1. Select “SOUND MODE”.
S.MODE
• Press the “S.MODE”on the remote control.
• While pressing the “S.MODE”for the first time, the current sound mode
will be displayed.
2. Every Press of the Button Changes Modes.
• Each time you press the button, a different sound mode appears.
The sequence used is as follows:
Normal Movie Music News User
Normal : Suitable for watching any motion picture
Movie : Select this mode to simulate being at a movie theatre
Music : Ideal for listening to music
News : Allows human voice to be heard more clearly
User : Allows the user to adjust as desired.
3. MENU will Disappear.
• After selecting a desired Sound Mode, the on-screen menu will disap-
pear in about 2~3 seconds.
• Normal, Movie, Music and News modes are factory preset values.
If you want to customise the sound modes for your preference, refer to
the following page.
User Manual BDH5031V
7.2 CUSTOMIZING SOUND MODE
• This feature allows the user to adjust for their preference.
1. Press the MENU Button.
• The MENU screen as below will be displayed.
Mode
Dynamic
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Select
Exit
2. Press the “/” Button.
• Select [Sound] by the “/”buttons, then press the
“”button to display the following.
Balance
Effect
0
Picture
Sound
Screen
Feature
Input
Off
Off
AVL
Mode
Normal
Equalizer
MENU
Exit
Exit
MMoovvee
SSeelleecctt
3. Select SOUND BALANCE.
• Select “Sound-Balance”by the “/”buttons, then
adjust it.
Balance
Effect
0
Picture
Sound
Screen
Feature
Input
Off
Off
AVL
Mode
Normal
Equalizer
MENU
Move
Adjust
Exit
User Manual BDH5031V
4. Select the Effect Mode.
Balance
0
• Select [Effect] by pressing the “/”buttons, then se-
lect the desire sound effect by pressing the “”button.
• [Effect]: Used to emphasize stereo effect.
• BBE is the sound enhancement clarifying the sound
and outputs finest quality. And M.Voice is the function
that you can hear clearer voice.
Picture
Sound
Screen
Feature
Input
Effect
AVL
Off
Off
Mode
Equalizer
Normal
S.EFFECT
• Effect Mode also can be selected by pressing “S.EFFECT”
button on the remote controller.
Off BBE M.Voice
MENU
Move
Adjust
Exit
5. Select the Sound Mode.
• Select the Sound Mode by pressing the “/”but-
tons, then adjust it by pressing the “/”buttons.
MENU
VOL
Balance
Effect
0
VOL
Picture
Sound
Screen
Feature
Input
Off
Off
AVL
Mode
Normal
Normal Movie Music News User
Equalizer
Normal : Suitable for watching any motion picture
Movie : Select this mode to simulate being at a movie theater
Music : Suitable for listening to music
News : Allows human voice to be heard more clearly
User : Allows the user to adjust as desired.
MENU
Move
Adjust
Exit
Notes:
1) User Mode : Used as an equalizer with which the user can adjust the
sound frequency as desired.
2) If you modify the sound frequency in auto Sound Mode (News, Movie,
Music, etc.), it is automatically switched to the User Mode.
3) For a realistic sound effect, lower than 120Hz frequency sound and
greater than 12kHz frequency adjust the equalizer accordingly.
4) AVL function : This function adjusts volume to the set level automatically.
However, dependent on the sources, it may have different volume levels
because the sound sources have their own initially set up levels.
User Manual BDH5031V
8. INPUT SIGNAL
8.1 SELECTING INPUT SIGNAL
• Used to select INPUT signal of external device connected to the PDP.
1. Press the Input Signal Selecting Button.
AV 1
• Press the “AV”button on the remote control, or select the de-
Picture
Sound
Screen
Feature
Input
AV 2
AV
sire input signal using Keypad of the PDP unit.
• When you press the “AV”button, you will see the OSD as
shown. You can move using “/”and select desire input
mode with “/”button.
AV 3
Component
PC
HDMI
Move
Select
Exit
Notes:
1) If an external device is not connected or INPUT signal is not applied a
Warning Message (“No Signal”) will be displayed.
2) In this case, check if external device is connected and / or terminal con-
nection is properly fitted.
3) Also, you can select input using [INPUT SELECT] button in the keypad of
the PDP unit
User Manual BDH5031V
8.2 CHECKING THE CURRENT INPUT SIGNAL
• Press the [RECALL] button on the remote control, then displays basic
informations of the current input signal, Under this state, pressing the
[RECALL] button once more, additional informations about the current
input signal will be displayed on the OSD.
• Used to check the INPUT signal mode, current time, resolution, etc.
RECALL
1. Press the “RECALL” Button.
• Press the “RECALL”button on the Remote Control.
Component
PM 12:00
H:1920
V:1080
1. If you watch Component, PC, or HDMI:
Displays which input terminal is used, and indicates the input signal mode.
Indicates the mode and current time.
Component
PM 12:00
H:1920
V:1080
Indicates the horizontal and vertical resolution of the current
input signal
2. If you watch VCR image:
Displays the program number and input terminal, which is used.
Indicates the mode and current time.
AV1
PM 12:00
Displays the video system of input signal
Video PAL B/G
Notes:
1) “1920 x 1080” displayed in the INPUT signal is not the resolution of the
set, but the signal that is sent by the Digital Broadcasting Receiver.
User Manual BDH5031V
9. OTHER FUNCTIONS
9.1 MENU BACKGROUND, LANGUAGE, KEYBOARD LOCK SETTING
AND RC LOCK SETTING
• Used to select the translucent level of MENU background and lan-
guage used in MENU.
Mode
Dynamic
1. Press the MENU Button.
• The MENU screen will be displayed as below.
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Select
Exit
MENU
Background
Language
10
VOL
VOL
2. Press the “/” button.
• Select [Feature] by the “/”button.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Select
Exit
Background
Language
10
3. Select the menu Background.
• Select the MENU [Background] by pressing the “”
button.
• Adjust the translucent level of OSD background using
“/”buttons.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Adjust
Exit
User Manual BDH5031V
4. Select LANGUAGE by using the “/” button.
• Select [Language] by using the “/”button.
• Every press of the “”button while you are in the
[Language] mode would cycle through the different
languages.
Background
10
10
10
Language
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
Notes:
* When power is turned on the first time, ‘SELECT LANGUAGE’ mode will be
displayed, then, select the desired language by using “” button.
(Displayed only once)
50
MENU
Move
Adjust
Exit
Exit
Exit
5. Keyboard Lock Setting.
Background
Language
• Select [Keyboard Lock] by the “/”buttons.
• Whenever “”button is pressed, the lock mode would
cycle On and Off.
• While the Keyboard Lock is ON, if you have not turned
off the PDP, all of it’s keys will work normally. However,
after turning the PDP off, the PDP will not be turned on with the key-
pad on the PDP. Only by the remote controller, the PDP is turned on.
• At Stand-By state while the Keyboard Lock is ON, the LED of the
Plasma unit will be flickering in red.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Adjust
6. RC Lock Setting.
• Select RC Lock by the “/”buttons.
• In order to turn the RC Lock on, press “”button of remote controller
or keyboard.
• When RC Lock is On, you cannot make it Off using remote controller.
Please use the keyboard instead of remote controller to unlock.
• In case of that both Keyboard Lock and RC Lock are On, you can
unlock those only using RS-232 control. Please reference‚SICP User
Manual’for the usage of RS-232 control.
Background
Language
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Adjust
User Manual BDH5031V
9.2 MGDI PLUS (META GENUINE DIGITAL IMAGE)
• MGDI Plus is the image enhancement technology of which provides
more clear, realistic, and delicate images.
• MGDI Plus function can not be used In PC and HDMI modes.
1. Press the MENU Button.
Mode
Dynamic
• The MENU screen will be displayed as below.
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Select
Exit
Exit
Exit
MENU
2. Select Feature.
Background
Language
10
VOL
VOL
• Select [Feature] by the “/”button.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Select
3. MGDI Plus Setting.
Background
Language
10
• Enter the sub Menu by using the “”button.
• Select the [MGDI Plus] by pressing the “/”button.
• You can select [MGDI Plus] On or Off mode by using
the “”button.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Adjust
User Manual BDH5031V
9.3 AUTO POWER SETTING
POWER/STANDBY Indicator
Front panel LED lights
• When the AC power is on : Green.
• When the AC power is in the stand-by mode : Red.
1. Auto Power Setting.
Background
10
• Select the [Auto Power] by pressing the “/”button
from [Feature].
• You can select [Auto Power] ON and OFF mode by us-
ing the “”button.
Language
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Adjust
Exit
Auto Power
1) ON : When the AC power is ON, the Monitor will be turned on au-
tomatically without pressing the power button on the remote
control.
AC POWER ON
PDP SET ON
Automatically
2) OFF : When the AC power is ON, the Monitor will be turned on by
pressing the power button on the remote control or the keypad
of the front panel.
AC POWER ON
STAND-BY MODE
PDP SET ON
With the remote control or the keypad
of front panel.
3) If Keyboard Lock function is ON, this function is not operated.
User Manual BDH5031V
9.4 TIME SETTING
1. Press the MENU Button.
Mode
Dynamic
• The MENU screen will be displayed as below.
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Select
Exit
Exit
Exit
MENU
VOL
2. Select Feature.
• Select [Feature] by the “/”button.
Background
Language
10
VOL
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Select
3. Select Time Setting.
Background
Language
10
• Enter the sub menu by using the “”button.
• Select the [Time Setting] with the “/”button.
• Enter [Time Setting] by pressing the “”button.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Select
User Manual BDH5031V
• The “Current time”must be set up ahead of setting up other time
memories.
4. Off-Time setting.
• Select Functions by pressing the “/”button.
First, set [Clock]- current time, and then You can setup
off-time.
Time Setting
MENU
Clock
AM 11 : 50
Off
Picture
Sound
Screen
Feature
Input
VOL
VOL
Off Timer
Off Time
AM 12 : 00
• [Clock] : Adjust the desired hour and minute with
“/" button.
• [Off Time] Setting methods are same as [Clock] setting method.
• [Off Timer] : Setting [On] and [Off] of each Timer.
MENU
Move
Adjust
Exit
Time Setting Functions
This time memory function automatically turns the Monitor set “Off”at
a desired time. Once set up, this function works every day unless the set
time is counselled or the Monitor set is unplugged.
User Manual BDH5031V
9.5 ANTI BURN-IN
• Displaying a still image for a long time causes part image sticking on
the screen.
• The Anti Burn-In function minimises this effect.
1. Press the MENU Button.
Mode
Dynamic
• The MENU screen will be displayed as below.
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
Sharpness
Colour
60
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Select
Exit
Exit
Exit
MENU
2. Press the “/” button.
Background
Language
10
VOL
VOL
• Select [Feature] by the “/" button.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Select
3. Select Anti Burn-In.
Background
Language
10
• Enter the sub menu by using the “”button.
• Select the [Anti Burn-In] by pressing the “/”button.
• Press of the “”button while you are in the Anti Burn-
In.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Select
User Manual BDH5031V
4. Select Functions.
Anti Burn-In
• Every press of the “”button after select function by
the “/”button would switch between ON/OFF.
Pixel Shift
Off
Off
Off
Picture
Sound
Screen
Feature
Input
Low Bright
Image Invert
MENU
Move
Adjust
Exit
Notes:
* Pixel Shift : The whole screen shifts up/down, left/right at 25 sec interval
to minimize image sticking.
PIXELSHIFT
* Low Bright : When displaying a still picture or a fixed pattern for a long
time (5Min), the brightness level decreases to minimize image sticking,
and the initial default value of Low Bright is ‚On’ state.
* Image Invert : Inverting colour of the original image to minimisation im-
age sticking.
User Manual BDH5031V
9.6 MODE RESET
Mode
Dynamic
Picture
Sound
Screen
Feature
Input
Brightness
Contrast
40
80
8
• You can restore the values of the adjustment setting made in the
MENU back to factory settings.
Sharpness
Colour
60
1. Press the MENU Button.
• The MENU screen will be displayed as below.
Colour Temp.
Noise Reduc.
Normal
On
MENU
Move
Select
Exit
Background
Language
10
2. Select Feature.
• Select [Feature] by the “/”button.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
Off
MENU
VOL
MGDI plus
On
VOL
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
50
MENU
Move
Select
Exit
Background
Language
10
3. Mode Reset.
• Enter the sub Menu by using the “”button.
English
Off
Picture
Sound
Screen
Feature
Input
Keyboard Lock
RC Lock
• Select the [Mode Reset] by pressing the “/”button, then press the
“”button.
• A confirmation message will be displayed.
• To perform Mode Reset, press the “”button after
selecting [Yes] by the “/”button.
Off
MGDI plus
On
Auto Power
Time Setting
Anti Burn-In
Mode Reset
Operation hrs.
Off
• To return to MENU, press„MENU”button.
50
MENU
Move
Select
Exit
Are you Sure?
Picture
Sound
Screen
Feature
Input
No
When [Mode Reset] is completed:
Yes
1) When [Mode Reset] is completed, those values that have been set in the
User Mode of [Picture Mode] and [Sound Mode] will be returned to the
factory preset values.
2) Once reset, you can not undo.
3) The items in the [Screen] Menu are also reset.
4) Language, Program, Time, Volume, OSD Background, input mode, Key-
board Lock, RC Lock and Operation Hour are not reset.
MENU
Move
Select
Exit
User Manual BDH5031V
9.7 SETTING SLEEP TIMER
• Sleep Timer turns the PDP off after a preset time.
1. Press the “TIMER” Button.
TIMER
• Press the “TIMER”button on the Remote Control.
• Pressing the “TIMER”button first time will display the current
setting for Sleep Timer.
• To cancel the Sleep Timer, press the “TIMER”button to select ‘Off’.
Sleep Timer off Sleep Timer 15 Sleep Timer 30 Sleep Timer
Sleep Timer Off
60 Sleep Timer 90 Sleep Timer 120 Sleep Timer off
Notes:
1) On-screen information disappears if you do not take any action for
about two seconds after pressing the TIMER button.
2) If you turn the PDP off after setting TIMER, the setting is erased.
User Manual BDH5031V
10. SPECIFICATIONS
DISPLAY UNIT
Diagonal Size
Screen Aspect Ratio
System
127cm(50”)
16 : 9
PAL B/G, ,D/K, I/I, SECAM B/G, D/K, L/L’
HD Panel: 1365(H) X 768(V) dots
HD Panel: 0.81(H) X 0.81(V) mm
Display Resolution
Pixel Pitch
1240(W) X 753(H) X 100.5(D) mm
(without Stand)
Dimension
1240(W) X 817(H) X 370(D) mm
(with Stand)
43.2Kg
Weight (without stand)
Power Requirement
100 - 240V~, 50/60Hz
* Appearance and specifications of this product are subject to change for improving the prod-
uct without prior notice.
CONNECTION TERMINAL
ITEMS
VIDEO
AUDIO
HDMI Jack
HDMI INPUT
One 15 pin D-sub jack
One 15 pin D-sub jack
RCA jack
PHONE Jack
INPUT
OUTPUT
PC
EXTER-
NAL
INPUT
(LEFT/RIGHT)
(LEFT/RIGHT)
RCA OUTPUT
Component INPUT
AV 1, 2
One Y Pb/Cb, Pr/Cr RCA jack
SCART jack
(Video In/Out, RGB In-AV1,
Video In-AV2)
(LEFT/RIGHT)
(In/Out)
RCA jack
(LEFT/RIGHT)
AV 3
AUDIO FEATURES
20W (10W + 10W), 8 Ohm
AUDIO OUTPUT
|
