Palsonic TFTV765 User Manual

OWNER'S MANUAL  
76CM CORDLESS REMOTE LCD TV/MONITOR  
MODEL: TFTV765  
N111  
PALSONIC CORPORATION PTY LTD  
1 JOYNTON AVENUE  
WATERLOO NSW 2017 AUSTRALIA  
TEL: (02) 9313 7111  
FAX: (02) 9313 7555  
PALSONIC CUSTOMER SERVICE  
TELEPHONE  
AUSTRALIA: 1300 657 888  
Important Safety Cautions  
When any unusual situation occurs, turn off the power supply at once and  
remove the plug from the wall outlet. Contact a qualified service department  
in your local area.  
Water and moisture - Do not use this product near water - for example, near a  
bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a  
swimming pool, and the like. Do not use immediately after moving from a low  
temperature to high temperature environment, as this causes condensation,  
which may result in fire, electric shock, or other hazards.  
Heat sources - Keep the product away from heat sources such as radiators  
heaters, stoves other heat generating products (including amplifiers).  
requirement of environment temperature;  
-200C~500C for storage; 00C~400C for working.  
The vents and other openings in the cabinet are designed for ventilation. Do not  
cover or block these vents and openings since insufficient ventilation can cause  
overheating and/or shorten the life of the product.  
Do not place the product on a bed, sofa, rug or other similar surface, since they  
can block ventilation openings.  
This product is not designed for built-in installation; do not place the product in an  
enclosed place such as a bookcase or rack, unless proper ventilation is provided  
or the the manufacturer's instructions are followed.  
Unplug this product from the wall outlet before cleaning. Do not use liquid  
cleaners or aerosol cleaners. Use a damp cloth for cleaning.  
Do not place the product on an unstable trolley, stand, tripod or table. Placing  
the product on an unstable base can cause the product to fall, resulting in  
serious personal injuries as well as damage to the product. Use only a trolley,  
stand, tripod, and bracket or table recommended by the manufacturer or sold with  
the product.  
2
Identification of controls  
Front  
Remote sensor  
Indicator  
To enter into MENU  
Volume up  
Volume down  
Channel up  
Channel down  
Power on/Standby  
To select input signal  
4
Back  
Video  
input  
Antenna input  
VGA input  
Audio inputs  
Earphone  
jack  
HDTV YPbPr  
inputs  
S-video input  
PC audio  
line in  
DC input  
Speaker  
outputs  
HDTV Audio inputs  
DVD inputs  
5
Identification of controls  
(continued)  
Remote Control  
Power on/Standby  
Volume down  
Sound Mute  
Channel up  
Volume up  
Channel down  
To enter into MENU  
To exit OSD menu  
Colour/Sound  
system select  
Zoom select  
Sleep timer  
Clock/Timer setting  
Previous channel  
Auto correct picture  
Picture mode select  
On-screen display  
Channel select  
/
Input signal select  
Still picture  
OSD position select  
Adjusting Bass  
Adjusting Treble  
6
Open the battery cover.  
5m  
POWER  
CH  
CH  
VOL  
-
VOL  
+
MENU  
ENTER  
C.SYS  
ZOOM  
CLK  
DSP  
SLP  
AUTO.ADJ  
P.M  
1
2
5
8
0
3
4
7
6
9
Install two "AAA" batteries  
matching the +/-  
-
/
--  
AV  
OSD  
STILL POSITION Bass+  
Treb+  
Treb-  
Bass  
-
polarities of the battery  
to the +/- marks.  
Notes:  
There should be no obstacle between the TV  
and the transmitter.  
Use the remote control within the effective  
range as the above figure.  
If the remote control does not work, please  
check whether the batteries are exhausted  
or the polarity is wrong.  
Replace the battery  
cover.  
When direct sunlight, and incandescent  
lamp, fluorescent lamp or any other strong  
light shines on the REMOTE SENSOR of the  
TV the remote operation may be unstable.  
Installation  
Antenna installation/Adaptor connection  
Before using this equipment, please connect the AC power adaptor correctly.  
Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial  
must be used. The exact type and position of the aerial will depend upon your particular area.  
AC power adapter  
Notes:  
Turn off the power firstly when you connect a outdoor antenna to the Antenna input terminal.  
When installing an outside antenna system, extreme care should be taken to keep from touching  
power lines or circuits as contact with them might be fatal.  
In thunder and lighting weather, please disconnect the outdoor antenna to avoid thunder/lighting  
strike.  
8
Connecting video/audio equipment  
Yellow (video)  
Y
W
R
White (audio L/MONO)  
Red (audio R)  
To S-video  
input  
To audio  
inputs  
R
W
R
W
Y
To audio  
inputs  
To video  
input  
To audio  
outputs  
W
R
To audio  
outputs  
To video  
output  
Video equipment  
with S-video terminal  
Y
W
R
To ANT output  
Video equipment  
without S-video terminal  
To ANT output  
9
Installation  
(continued)  
Connecting DVD Player and speakers  
Red Black Red  
To YCbCr  
inputs  
To audio  
inputs  
B
R
R
W
G
To speaker  
To YCbCr  
To audio  
outputs  
outputs  
G
B
R
W
R
DVD Player  
W
R
White (audio L/MONO)  
Red (audio R, Cr)  
Green (Y)  
G
B
Blue (Cb)  
10  
Connecting YPbPr terminals  
To YPbPr  
inputs  
To audio  
inputs  
R
B
W
R
G
To YPbPr  
outputs  
To audio  
W outputs  
W
R
White (audio L/MONO)  
Red (audio R, Pr)  
Green (Y)  
B
R
R
G
G
B
Blue (Pb)  
SET TOP BOX  
(Or other equipment with YPbPr output terminals)  
11  
Installation  
(continued)  
Connecting VGA interface  
To LINE in  
To VGA input interface  
Equipment with  
VGA output interface  
To LINE out  
To VGA output  
interface  
12  
Elevation adjustment  
You can adjust the angle of the LCD TV/Monitor as follows.  
The elevation can be adjusted from -50 to +100.  
13  
There are four pages of MENU in TV, PC and YPbPr mode.  
In MENU operations, the CH / buttons are used to select  
item upwards or downwards; the VOL+/- buttons are used to  
adjust or confirm selected item.  
Menu Introduction  
Press MENU button in TV mode  
To adjust the picture's brightness.  
To adjust the picture's contrast.  
PICTURE SETTING  
-
-
-
-
-
50  
50  
50  
50  
50  
+
+
+
+
+
Brightness  
Contrast  
Color  
Sharpness  
Tint  
To adjust the picture's colour saturation.  
To adjust the picture's sharpness.  
<V-> or V+> key to change  
To adjust the picture's skin colour. (This item is  
available only in NTSC).  
Press  
MENU  
button  
SOUND  
To adjust the Bass.  
To adjust the Treble.  
To adjust the Balance.  
-
25  
25  
25  
+
Bass  
-
-
+
+
Treble  
Balance  
<V-> or V+> key to change  
Press  
MENU  
button  
To adjust colour system.  
SETUP  
To adjust sound system.  
Color sys  
AUTO  
BG  
Sound sys  
To select OSD menu language.  
To select OSD menu position.  
To set OSD background.  
Language  
Eng  
OSD position  
OSD background  
Upper Left  
Opaque  
<V-> or V+> key to change  
Press  
MENU  
button  
To start auto search.  
CHANNEL SETTING  
To enter into channel search menu.  
To enter into fine tuning menu.  
Auto search  
Search  
Fine Tune  
Change Prog  
Current Prog  
Change to Prog  
Skip  
To exchange current channel with  
the selected target channel.  
To display current channel number.  
To select a target channel to exchange with current  
channel.  
To skip or unskip, current channel.  
12  
15  
ON  
<V-> or V+> key to change  
14  
To adjust picture's brightness and contrast in  
PC mode. (not affect picture in TV or AV mode)  
Press MENU button in PC mode  
PICTURE SETTING  
-
-
-
-
-
-
-
+
+
+
+
+
+
+
25  
25  
25  
25  
25  
25  
25  
Brightness  
Contrast  
If the best picture can not be obtained after many  
times of auto correction, you can adjust these two  
items to obtain the best picture.  
Phase  
Frequency  
USER_R  
USER_G  
USER_B  
Color Temp  
Only when the "Color temp" is set to "User",  
these three items are adjustable.  
9300K  
<V-> or V+> key to change  
To adjust colour temperature between 9300K,  
7300K, 6500K, and User.  
Press  
MENU  
button  
PICTURE POSITION  
-
-
25  
25  
+
When the VGA input signal is nonstandard,  
adjust these two items until proper picture  
position is obtained.  
Horizontal  
Vertical  
Reset  
+
<V-> or V+> key to change  
To reset to factory settings.  
Press  
MENU  
button  
To adjust the Bass.  
To adjust the Treble.  
SOUND  
-
-
-
25  
+
+
+
Bass  
25  
25  
Treble  
Balance  
To adjust the Balance.  
<V-> or V+> key to change  
Press  
MENU  
button  
SETUP  
To select OSD menu language.  
To select OSD menu position.  
To set OSD background.  
Language  
Eng  
OSD position  
Upper Left  
Opaque  
OSD background  
<V-> or V+> key to change  
15  
Channel Preset  
To enter into CHANNEL SETTING menu  
1. Press MENU button repeatedly to display CHANNEL SETTING  
menu.  
2. Press CH or CH button to select item.  
3. Press VOL+ or VOL- button to confirm or adjust selected item.  
Auto Search  
Please enter into CHANNEL SETTING menu and select Auto Search  
item.  
Press VOL- or VOL+ button to start Auto Search and all active  
programs will be memorised.  
During the process of Auto Search, pressing  
Auto search..  
10  
VHFL  
MENU button will stop Auto Search.  
Press <Menu> to escape  
Please confirm the sound system is correct according to your area  
before Auto Searching.  
Manual Search  
Use manual search function if desired channels cannot be preset or if  
you would like to preset channels to specific position numbers one by  
one.  
Use 0~9 digit buttons or CH / buttons to  
select a position number firstly, then enter into  
CHANNEL SETTING menu and select Search  
Channel searching.. VHFL 10  
item. Press VOL+ button to enter Channel  
Press <V->/<V+> to search channel  
Press <P->/<P+> to shift band  
Search sub-menu, then press VOL+ or VOL- to  
start manual search.  
Press MENU button can exit Channel Search  
sub-menu.  
In area of inferior broadcast conditions where adjustment is necessary  
for a better picture and sound, use Fine tuning.  
/
Use 0~9 digit buttons or CH  
buttons to  
select the desired channel, then enter into  
CHANNEL SETTING menu and select Fine  
tune item. Press VOL+ button to enter into Fine  
tuning sub-menu, then press and hold VOL+ or  
VOL- to start Fine tuning.  
Fine Tuning..  
10  
VHFL  
Press <Menu> to change  
17  
Channel Preset  
(continued)  
CHANNEL SETTING  
Auto search  
Channel Skipping  
Search  
Fine Tune  
Change Prog  
Current Prog  
Change to Prog  
Skip  
You can skip unnecessary channels by using Skip function when you  
12  
15  
/
browse program by CH  
buttons.  
ON  
/
Use 0~9 digit buttons or CH  
buttons to select a unwanted channel  
firstly, then enter into CHANNEL SETTING menu and select Skip item.  
<V-> or V+> key to change  
Press VOL+/- button to select ON to skip this channel. Now this channel  
/
will be skipped when you browse channels with CH  
button.  
To restore the skipped channel, please select the skipped channel with  
0~9 digit buttons and then enter the CHANNEL SETTING menu, select  
Skip item and press VOL+/- to set Skip to OFF.  
POWER  
CH  
CH  
VOL  
VOL  
+
Channel Edit  
-
After Auto Channel Preset, this function is for you to edit the order of  
programs conveniently according to your favourite.  
ENTER  
MENU  
C.SYS  
SLP  
ZOOM  
CLK  
DSP  
Please enter into CHANNEL SETTING  
menu and select Change to Prog item by  
CHANNEL SETTING  
Auto search  
Search  
CH  
buttons, press VOL+/- button to  
/
AUTO.ADJ P.M  
Fine Tune  
Change Prog  
Current Prog  
Change to Prog  
Skip  
select a target channel to exchange with  
current channel. Then select Change  
Prog item and press VOL+/- to confirm.  
Now the program in current channel  
number exchanges with the program in  
the target channel number.  
12  
15  
ON  
1
2
5
8
0
3
<V-> or V+> key to change  
6
9
4
7
-
/
AV  
--  
OSD  
POSITION  
Treb+  
Treb-  
STILL  
Bass+  
Bass -  
18  
Channel Select  
Use 0~9 digit buttons and -/-- button  
Use 0~9 digit buttons to select one-digit channel number.  
8
Press -/-- button  
to display "-".  
Press 0-9 direct  
channel selector.  
-
8
POWER  
To select two-digit channel:  
CH  
CH  
Press -/-- button  
repeatedly to  
display "--".  
Press 1-9  
buttons.  
Press 0-9  
buttons.  
-1  
- -  
18  
VOL  
-
VOL  
+
ENTER  
MENU  
C.SYS  
SLP  
ZOOM  
CLK  
DSP  
To select three-digit channel:  
AUTO.ADJ P.M  
Press -/-- button  
repeatedly to  
display "--".  
Press 1-9  
buttons.  
Press 0-9  
buttons.  
Press 0-9  
buttons.  
---  
180  
--1  
-18  
1
2
5
8
0
3
6
9
4
7
-
/
AV  
--  
Using CH  
/
button  
Press CH button, the channel number increases;  
Press CH button, the channel number decreases.  
OSD  
POSITION  
Treb+  
Treb-  
STILL  
Bass+  
Bass -  
Use previous channel button  
Press this button to switch between the current channel and  
previous channel.  
19  
Picture Adjustment  
PICTURE SETTING  
Adjusting picture  
-
-
-
-
-
50  
50  
50  
50  
50  
+
+
+
+
+
Brightness  
Contrast  
Color  
1. Press MENU button to display PICTURE SETTING menu.  
Sharpness  
Tint  
/
2. Press CH  
button to select item.  
<V-> or V+> key to change  
3. Press VOL+/- button to adjust the selected item.  
VOL-  
darker  
weaker  
paler  
softer  
purplish  
Item  
Bright  
Contrast  
Saturation  
Sharpness  
Tint*  
VOL+  
lighter  
stronger  
deeper  
sharper  
greenish  
POWER  
CH  
CH  
VOL  
-
VOL  
+
ENTER  
MENU  
* Note: The item Tint is for NTSC only.  
C.SYS  
SLP  
ZOOM  
CLK  
DSP  
The adjusted settings are stored in the User mode.  
There are three preset picture modes and one User-set picture  
mode. Press the P.M button to select a picture mode according to  
your favourites.  
AUTO.ADJ P.M  
4. Press P.M button to select picture mode.  
1
2
5
8
0
3
You can quickly select picture mode by P.M button. There are  
four picture mode: Bright, Standard, Mild and User mode.  
6
9
4
7
Using STILL button  
-
/
You can still current screen picture by pressing STILL button on  
the remote. Press this button again to resume.  
AV  
--  
OSD  
POSITION  
Treb+  
Treb-  
STILL  
Bass+  
Using AUTO.ADJ button  
Bass -  
When wrong picture identification occurs, you can use  
AUTO.ADJ button on the remote to obtain a correct picture.  
20  
SOUND  
-
-
-
25  
25  
25  
+
+
+
Bass  
Treble  
Balance  
<V-> or V+> key to change  
/
Item  
Bass  
VOL-  
weaker  
VOL+  
stronger  
Treble  
Balance  
weaker  
decreases the  
right channel  
stronger  
decreases the  
left channel  
You can quickly adjust Bass and Treble by using Bass+/Bass-  
and Treb+/Treb- buttons on the remote.  
Adjusting Volume  
You can use VOL+ or VOL- button to adjust volume.  
Press VOL+ button, the volume increase;  
Press VOL- button, the volume decrease.  
If you want to mute the sound, press button on the remote.  
To resume the sound, press this button again or you can also  
press VOL+ or VOL- to resume the sound.  
Setting Sound mode  
Color sys  
AUTO  
BG  
This unit can receive both stereo and  
bilingual broadcasts Transmitted in either  
NICAM or A2 broadcast system.  
Sound sys  
Sound mode  
AUTO  
Press C.SYS button on the remote to call up the menu as shown on the  
/
above, press CH  
to select Sound mode item, then making use of  
VOL+/- to select a desired sound mode. See the following chart for a  
possible choice.  
* When receiving broadcasts transmitted in NICAM system:  
Broadcast  
Choice  
mode  
* When receiving broadcasts transmitted in A2 system:  
Broadcast  
FM/AM MONO  
MONO  
NICAM MONO*(default)  
NICAM STEREO*(default)  
NICAM A*(default) NICAM B  
FM/AM MONO  
& NICAM MONO  
Choice  
mode  
FORCE MONO  
FORCE MONO  
FORCE MONO  
FM MONO  
MONO  
FM/AM MONO  
& NICAM STEREO  
FM STEREO  
FORCE MONO  
FM A (default)  
FM STEREO* (default)  
FM/AM MONO  
& NICAM BILINGUAL  
FM BILINGUAL  
FM B  
Note: "Default" means the choice is a default one. If you do not select other choice, the TV will be in default  
sound mode. Please according to your local area's broadcasting condition, select your desired sound mode.  
Sound mode function is an optional function. It is only available in certain version.  
SETUP  
Color sys  
AUTO  
BG  
Sound sys  
Language  
Eng  
OSD position  
OSD background  
Upper Left  
Opaque  
<V-> or V+> key to change  
.
You can quickly access colour and sound system by using C.SYS  
button on the remote.  
.
In some model, the Colour system and Sound system have been  
preset and cannot be adjusted.  
/
SETUP  
From the SETUP menu, press CH  
select Language item. Press VOL- or  
VOL+ button to select OSD language.  
to  
Color sys  
AUTO  
BG  
Sound sys  
Language  
Eng  
OSD position  
OSD background  
Upper Left  
Opaque  
<V-> or V+> key to change  
SETUP  
Setting OSD position  
Color sys  
AUTO  
BG  
Sound sys  
/
Language  
Eng  
From the SETUP menu, press CH  
to select OSD position item.  
OSD position  
OSD background  
Upper Left  
Opaque  
Press VOL- or VOL+ button to select an OSD position in your  
preference.  
<V-> or V+> key to change  
You can quickly select OSD position by using OSD position button on  
the remote.  
Setting OSD Background  
SETUP  
/
From the SETUP menu, press CH  
to  
Color sys  
AUTO  
BG  
select OSD Background item. Press  
Sound sys  
VOL- or VOL+ button to select Opaque or  
Translucent.  
Language  
Eng  
OSD position  
OSD background  
Upper Left  
Opaque  
<V-> or V+> key to change  
Setting ZOOM mode  
This unit allows you to adjust screen aspect ratio in your preference.  
You can quickly select screen ratio by using ZOOM button on the  
remote.  
Press ZOOM button to select a proper screen aspect ratio between  
Anamorphic, 4:3 and Panorama in TV, AV, S-Video and YCbCr mode.  
Press ZOOM button to select a proper screen aspect ratio between Fill  
all and Normal in PC and YPbPr mode.  
23  
Timer  
Use SLP button  
Press SLP button repeatedly to set sleep time between: 0, 10, 20, 30, 60,  
90,120,180,240 minutes. If you select 0 minute, it means the sleep timer  
function is turned off.  
Turn off  
0
Use CLK button  
Press CLK button, the Time menu appears.  
POWER  
Current time  
0:40  
/
Use CH  
to select hour or minute (the  
selected item is displayed in white), use  
VOL+/- to set the time.  
CH  
VOL  
-
VOL  
+
Press CLK button twice, the Turn off menu  
appears. Use VOL+/- to set the OFF time.  
CH  
ENTER  
MENU  
Turn off  
0
C.SYS  
SLP  
ZOOM  
CLK  
DSP  
Press CLK button three times to close the menu.  
AUTO.ADJ P.M  
1
2
5
8
0
3
6
9
4
7
-
/
AV  
--  
OSD  
POSITION  
Treb+  
Treb-  
STILL  
Bass+  
Bass -  
24  
Adjustments in YPbPr mode  
To enter into YPbPr mode  
Repeatedly press AV button on the remote control or SOURCE button on  
the set's panel until the screen display YPbPr, which indicates that the set  
is in YPbPr mode. Connect the YPbPr terminals to Set Top Box and make  
sure there is a signal input.  
YPbPr  
Adjusting picture  
PICTURE SETTING  
In YPbPr mode when there is correct input  
signal, press MENU button and PICTURE  
POWER  
-
-
-
-
-
-
-
+
+
+
+
+
+
+
25  
25  
25  
25  
25  
25  
25  
Brightness  
Contrast  
Saturation  
Sharpness  
USER_R  
USER_G  
USER_B  
/
SETTING menu appears, Use CH  
to  
select item and VOL+/- to adjust.  
CH  
CH  
VOL  
-
VOL  
+
Color Temp  
9300K  
Item  
Bright  
Contrast  
Saturation  
Sharpness  
VOL-  
darker  
weaker  
paler  
VOL+  
lighter  
stronger  
deeper  
sharper  
<V-> or V+> key to change  
ENTER  
MENU  
C.SYS  
SLP  
ZOOM  
CLK  
DSP  
softer  
AUTO.ADJ P.M  
Adjusting Colour temperature  
1
2
5
8
0
3
You can select different Colour temperature  
to obtain correct white. Press MENU button,  
PICTURE SETTING  
6
9
4
7
-
-
-
-
-
-
-
+
+
+
+
+
+
+
25  
25  
25  
25  
25  
25  
25  
Brightness  
Contrast  
/
use CH  
to select Color Temp item,  
Saturation  
Sharpness  
USER_R  
USER_G  
USER_B  
press the VOL+/- to select between User,  
9300K, 7300K, 6500K.  
-
/
AV  
--  
Color Temp  
9300K  
The USER_R, USER_G and USER_B can  
not accessed and adjusted unless you  
set Color Temp to "User".  
OSD  
POSITION  
<V-> or V+> key to change  
Treb+  
Treb-  
STILL  
Bass+  
Bass -  
Adjusting horizontal/vertical position  
Press MENU button twice and the PICTURE POSITION menu appears.  
/
Use CH  
to select item and VOL+/- to adjust.  
When a nonstandard signal input to the set  
and the picture may not be in the screen  
centre. Now you can adjust its horizontal  
and vertical position to display correctly.  
PICTURE POSITION  
-
-
25  
25  
+
Horizontal  
Vertical  
Reset  
+
<V-> or V+> key to change  
25  
Adjustments in PC mode  
To enter into PC mode  
Repeatedly press AV button on the remote control or SOURCE button on  
PC  
the set's panel until the screen display PC, which indicates that the set is  
in PC mode.  
PC signal format  
Please connect VGA input and be sure that there is VGA input signal. The  
signal format should be one of the follows:  
640 x 480 @60Hz  
POWER  
800 x 600 @60Hz  
1024 x 768 @60Hz  
1280 x 768 @60Hz  
CH  
CH  
VOL  
-
VOL  
+
ENTER  
MENU  
We recommend you to use 1024 x 768 @60Hz (4:3) or 1280 x 768 @ 60 Hz  
(16:9) so that the set can obtain the best picture.  
C.SYS  
SLP  
ZOOM  
CLK  
DSP  
AUTO.ADJ P.M  
Use AUTO.ADJ button  
1
2
5
8
0
3
When PC signal format changes or when you switch to PC mode by AV  
button, the set corrects picture automatically including frequency and  
phase to obtain the best display. During the process of auto correction, all  
buttons on the remote control and set's panel do not work until this  
process is finished.  
When the set displays some signal formats that are nonstandard and can  
not adjust by itself to the best displaying status, now you can press  
AUTO.ADJ button to correct the displaying again.  
6
9
4
7
-
/
AV  
--  
OSD  
Treb+  
Treb-  
STILL  
Bass+  
POSITION  
Bass -  
26  
When there is correct input signal, press MENU button and PICTURE  
PICTURE SETTING  
-
-
-
-
-
-
-
+
+
+
+
+
+
+
25  
25  
25  
25  
25  
25  
25  
Brightness  
/
SETTING menu appears. Use CH  
to select item and VOL+/- to  
Contrast  
Phase  
adjust  
Frequency  
USER_R  
USER_G  
USER_B  
Color Temp  
Adjusting brightness and contrast  
9300K  
<V-> or V+> key to change  
You can adjust bright and contrast in PC mode and this adjustment  
does not effect the brightness and contrast in TV and AV mode.  
Adjusting phase and frequency  
POWER  
If you can not obtain the best display after  
PICTURE SETTING  
-
-
-
-
-
-
-
+
+
+
+
+
+
+
25  
25  
25  
25  
25  
25  
25  
Brightness  
auto correction for many times. Now you  
can adjust phase and frequency to obtain  
the best display.  
Contrast  
CH  
CH  
Phase  
Frequency  
USER_R  
USER_G  
USER_B  
Color Temp  
VOL  
-
VOL  
+
ENTER  
MENU  
9300K  
<V-> or V+> key to change  
C.SYS  
SLP  
ZOOM  
CLK  
DSP  
AUTO.ADJ P.M  
Adjusting Colour temperature  
You can select different Colour temperature  
to obtain correct white. Press MENU button,  
PICTURE SETTING  
1
2
5
8
0
3
-
-
-
-
-
-
-
+
25  
Brightness  
+
+
+
+
+
+
25  
25  
25  
25  
25  
25  
Contrast  
/
use CH  
to select Color Temp item,  
Phase  
6
9
4
7
Frequency  
USER_R  
USER_G  
USER_B  
Color Temp  
press the VOL+/- to select between User,  
9300K, 7300K, 6500K.  
The USER_R, USER_G and USER_B can  
not accessed and adjusted unless you  
set Color Temp to "User".  
9300K  
<V-> or V+> key to change  
-
/
AV  
--  
OSD  
POSITION  
Treb+  
Treb-  
STILL  
Bass+  
Bass -  
27  
Trouble shooting  
Before calling service personnel, please check the following chart for a possible cause to the trouble  
you are experiencing.  
Symptoms  
Check the following items  
Be sure the power cord is plugged in.  
Power is not turned on.  
Poor colour, poor tint.  
Contrast, colour, tint are not correctly adjusted.  
Possible interferences of automobiles, motorcycle,  
trolley bus, neon lamps, etc.  
Spots appear on the screen.  
Possible interference of electronic interference  
from another TV set, a computer, an electronics  
game machine, a broadcast station, etc.  
Stripes appear on the screen.  
Double images or "ghosts".  
Snowy picture.  
This may be caused by reflections from nearby  
mountains or buildings.  
Check the antenna direction.  
It is possible that the aerial "lead-in" is damaged or  
has come off.  
Check the antenna direction.  
Even if the picture or the sound is normal, changes  
in the room temperature sometimes make the TV  
cabinet expand or contract, making a noise. This  
does not indicate a malfunction.  
TV cabinet creaks.  
The batteries may be worn out.  
The batteries may be installed with their polarity  
reversed.  
Remote control does not  
work.  
Unplug the power cord, wait for some seconds.  
Then re-plug the power cord and turn on the unit  
again.  
Control buttons do not work  
LCD Display panel information  
Important Information Regarding Use of Video Games, Computers, Captions or Other Fixed Image Displays.  
The extended use of fixed image program material can cause a permanent "shadow image" on the LCD panel.  
This background image is viewable on normal programs in the form of a stationary fixed image. This type of irreversible  
LCD panel deterioration can be limited by observing the following steps:  
A. Reduce the brightness/contrast setting to a minimum viewing level.  
B. Do not display the fixed image for extended periods of time.  
C. Turn the power off when not in actual use.  
Note:  
The marking or retained image on the LCD panel resulting from fixed image use is not an operating defect and as such  
is not covered by Warranty. This product is not designed to display fixed image patterns for extended periods of time.  
28  
29  
PALSONIC CORPORATION PTY LTD  
1 JOYNTON AVENUE  
WATERLOO NSW 2017 AUSTRALIA  
TEL: (02) 9313 7111  
FAX: (02) 9313 7555  
PALSONIC CUSTOMER SERVICE  
TELEPHONE  
AUSTRALIA: 1300 657 888  
604-L32B13-07A  
Ver. 1.0  

JVC AV 28BT8EES User Manual
JVC C 13910 C 13911 C 20910 AV 20920 AV 20921 AV 27920 User Manual
Lenovo 3000 J 8457 User Manual
Motorola C1213A User Manual
Motorola Cordless Telephone MD451 User Manual
Panasonic DMR E80H User Manual
Panasonic KX TS730AZ User Manual
Philips 190P5 User Manual
Philips Brilliance 14L4521599 User Manual
Philips HTS5310S User Manual