MODEL L75-A94
®
Basic Owner’s Guide
3
CAUTION
FCC Declaration of Conformity
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Product:
Models:
Projection Television Receiver
L75-A94
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Responsible Mitsubishi Electric Visual Solutions
Party:
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone:
1 (800) 332-2119
The lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the
user of the presence of uninsulated “danger-
ous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the literature accompa-
nying the product.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursu-
ant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment gener-
ates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
MAINS DISCONNECTION: The mains plug is used
as the disconnect device. The mains plug shall remain
readily operable.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
TV WEIGHT: This TV is heavy. Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and discon-
nect all cables before moving it.
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
the receiver.
Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV techni-
cian for help.
-
-
-
Stand Requirement
Mitsubishi does not design, manufacture or sell matching
bases for the L75-A94 model television. When selecting
a stand, base, or other furniture to support the TV, please
make sure it is designed with the appropriate dimen-
sions for stability and to support the TV’s weight plus the
weight of any additional equipment you plan to store.
Changes or modifications not expressly approved by
Mitsubishi could cause harmful interference and would
void the user’s authority to operate this equipment.
Custom cabinet installation must allow for proper
air circulation around the television.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS
PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTEN-
TION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES
GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTIC-
ULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CON-
NECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS
CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.
This apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
Children and TV Viewing
The American Academy of Pediatrics discourages televi-
sion viewing for children younger than two years of age.
For assistance call 1(877) 675-2224
4
Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
E XAMP LE OF ANTE NNA G R OUNDING
ANTE NNA
LE AD IN WIR E
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
G R OUND C LAMP
ANTE NNA
DIS C HAR G E UNIT
(NE C AR TIC LE 810-20)
E LE C TR IC
S E R VIC E
E QUIP ME NT
4) Follow all instructions.
G R OUNDING
C ONDUC TOR S
(NE C AR TIC LE 810-21)
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
G R OUND C LAMP S
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
P OWE R S E R VIC E G R OUNDING
E LE C TR ODE S YS TE M
NE C — NATIONAL E LE C TR IC AL C ODE
(NE C AR T 250, P AR T H)
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts speci-
fied by the manufacturer or have the same character-
istics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
ENERGY STAR®
This is an ENERGY STAR qualified TV. Products
that earn the ENERGY STAR prevent greenhouse
gas emissions by meeting strict energy efficiency
guidelines set by the U.S. Environmental Protection
Agency and the U.S. Department of Energy.
®
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
This TV uses power within ENERGY STAR guidelines
unless:
•
Picture Mode is set to Brilliant or Super Bril-
liant (Picture > Video menu)
•
Ambient Light Sensor is set to Off (Setup >
Energy menu)
For assistance call 1(877) 675-2224
5
Contents
Important Safety Instructions. . . . . . . . . . . . . . . . 2
Cleaning Recommendations. . . . . . . . . . . . . . . . . 3
Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cleaning Recommendations
Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is
needed, please use the following guidelines:
First, turn off the TV and unplug the power cord from
the power outlet.
1 Basic Setup and Operation
Package Contents . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Remote Control Batteries. . . . . . . . . 5
TV Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . 5
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setting Up and Using TV Inputs. . . . . . . . . . . . . . 7
Basic TV Operation. . . . . . . . . . . . . . . . . . . . . . . 9
TV Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using a
vacuum cleaner with a brush attachment.
Top and Sides of the TV
•
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel, microfiber, or a clean
cloth diaper, lightly moistened with water. Dry with
a second dry, soft, non-abrasive cloth.
2 TV Connections
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . 13
Connection Types and Audio/Video Quality . . . . 13
Cable Routing . . . . . . . . . . . . . . . . . . . . . . . . . 13
Input and Output Jacks. . . . . . . . . . . . . . . . . . . 14
Connection Diagrams . . . . . . . . . . . . . . . . . . . . 15
3 TV Features
FAV (Favorites) . . . . . . . . . . . . . . . . . . . . . . . . . 19
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ChannelView Channel Listings. . . . . . . . . . . . . . 20
StreamTV™ Internet . . . . . . . . . . . . . . . . . . . . . 21
3D Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
•
For oily dirt, add a few drops of mild liquid deter-
gent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
Screen
Appendices
•
•
•
Follow the instructions for the top and sides, wiping
gently in an up and down motion.
Clean the entire screen evenly, not just sections of
the screen.
Do not allow liquid to drip down the screen, as
some liquid may enter the TV through the gap
between the screen and screen frame.
You may purchase Mitsubishi Screen Cleaner, part
number CLEANER-VSS, by calling 1 (800) 553-7278.
Appendix A: Auto Input Sensing . . . . . . . . . . . . 27
Appendix B: Troubleshooting . . . . . . . . . . . . . . 28
Mitsubishi TV Software. . . . . . . . . . . . . . . . . . . . 32
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
MEVSA Internet Applications Policy . . . . . . . . . . 37
•
General Cleaning Precautions
•
•
•
DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
TV Software
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
•
Do not attempt to update the software of this TV
with software or USB drives not provided by or
authorized by Mitsubishi Electric Visual Solutions
America, Inc. Non-authorized software may damage
the TV and will not be covered by the warranty.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
•
•
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
•
Automatic software updates will be downloaded
over the internet to the TV if StreamTV is set up and
connected to the internet.
DO NOT scrub or rub the TV harshly. Wipe it gently.
Note: Features and specifications described in this
owner’s guide are subject to change without notice.
For assistance call 1(877) 675-2224
6
Laser Safety
Laser Safety
•
•
This TV is in compliance with the requirements of IEC
60825-1 Ed. 2(2007).
This TV is a CLASS 1 laser product. This TV poses
no risk to eyes or skin during normal use. An expo-
sure hazard may exist only if the protective housing
is removed.
•
•
This TV contains a CLASS 4 laser device, which by
itself may be hazardous. However, this TV incorpo-
rates a protective housing, optics and electronics
such that there should be no exposure to unsafe
levels of laser light during normal operation and
proper service.
Do not open this product. No consumer controls
®
are inside. Only a trained LASERVUE technician
should service this TV. Please call Mitsubishi for
assistance at 1 (877) 675-2224.
This label is located on the right lower back of the
television set.
Safe Operation
•
Always inspect the TV for damage after moving
it. If the cabinet or screen is physically damaged,
DO NOT connect the TV to an AC outlet. Call
1 (877) 675-2224 for assistance.
CAUTION
ATTENTION
CLASS 4 LASER LIGHT WHEN
OPEN AVOID EYE OR SKIN
EXPOSURE TO DIRECT OR
SCATTERED RADIAITON
LUMIÈRE LASER DE CLASSE 4 - EN CAS
D’OUVERTURE EXPOSITION DANGERE-
USE AU RAYONNEMENT DIRECT OU
DIFFUS DES YEUX OU DE LA PEAU
DO NOT power on the TV until it has been repaired
by qualified service personnel authorized by
Mitsubishi. See “Service and Customer Support”
page 29.
This class-4 label and similar service warning labels
are located inside the back cover of the television in an
area that should not be accessed by the user under any
circumstances.
•
•
Caution. Use of controls or adjustments or per-
formance of procedures other than those specified
herein may result in hazardous radiation exposure.
An additional class-4 label is located at the lower front
access panel under the front decorative bezel.
Use external or remote controls to operate the
product. Connection to signal sources and power
are accomplished through the external connectors.
Damage and Repair
•
There are no user serviceable components in this
TV. Do not attempt to disassemble any part of the
TV.
•
If damaged, the device must not be powered on or
used until it is repaired by qualified service person-
nel authorized by Mitsubishi. See “Service and
Customer Support” page 29.
•
Under no circumstances shall attempts be made to
operate this device without the screen in place or if
any portion of the enclosure, including the screen,
is cracked, broken, a liquid is spilled onto the TV or
is otherwise damaged.
This class-4 label is located at the center back of the TV
under the outer cover.
For assistance call 1(877) 675-2224
7
1 Basic Setup and Operation
TV Overview
Package Contents
Please take a moment to review the following list of
items to ensure that you have received everything.
Internal IR
Emitters for 3D
Glasses
POWER
Remote
Control
Indicator Light
(page 31)
POWER
Two AA
Batteries
• IR Sensor
• Ambient Light Sensor
Quick
Setup
Guide
Basic
Owner’s
Guide
Note: Do not block the area in
front of the sensors and emitters.
AA
AA
Control Panel. To display the main menu
Product
Registration
Card
without using the remote control, press
Cable Tie
+
INPUT and VOL simultaneously for about
10 seconds. Press and hold INPUT and
+
VOL for 10 seconds to clear the menu.
Location of internal
antennas. Keep
this area clear of
external wireless
transmitters.
Installing the Remote Control
Batteries
1. Remove the remote control’s back cover by
gently pressing in the tab and lifting off the cover.
Rear Connection Jacks
2. Load the batteries, making sure the polarities
(+) and (-) are correct. For best results, insert
the negative (-) end first.
3. Snap the cover back in place.
Before You Begin
1
The remote
control
requires two
AA batteries.
1. Review the important safety, installation, and oper-
ating information at the beginning of this book.
2. Choose a location for your TV.
•
•
See the stand requirements on page 1.
Allow at least four inches of space on all sides
of the TV to help prevent overheating. Over-
heating may cause premature failure of the TV.
Avoid locations where light may reflect off the
screen.
•
2
3. Install the batteries in the remote control.
4. Plug the TV into an AC power outlet.
For assistance call 1(877) 675-2224
8
1. Basic Setup and Operation
Remote Control
Sleep Timer, page 19
Number/letter keys
Channel tuning, page 8
Powers TV on or off.
Pass-code entry
TOOLS key shortcuts, this page
Adds a separator in digital channel
numbers. Clears some menu entries.
Returns to the previous channel.
In menus, steps back one menu.
LAST
Mutes the TV speakers.
MUTE
TOOLS
Displays up to nine favorite
sources, page 19.
Displays shortcuts for the number keys.
Press to check if shortcuts are available
for the current device.
FAV
Changes picture shape,
page 10
FORMAT
INTERNET
INPUT
VOL Controls volume of TV speakers.
Connects to internet content,
page 21.
CH
Changes channels; moves to another
page in a menu or list.
PAGE
Press to select a TV input,
page 8.
ENTER
Selects a channel number or menu item.
Navigation and adjustment controls
AUDIO
Audio settings
Video settings
VIDEO
MENU
GUIDE
INFO
ChannelView channel listings. Set the
TV clock to receive correct updates.
Displays or clears the TV main
menu (page 12). Also steps
back one menu.
TV status or TV help (page 11)
EXIT
Clears all menus and on-screen
displays.
(
PAUSE) Freezes a broadcast TV picture
Playback controls for StreamTV inter-
net services. May apply to compat-
ible devices under HDMI control. See
the supplemental Owner’s Guide at
www.mitsubishi-tv.com for setup of
HDMI control.
F1–F4. Function keys for some
StreamTV internet services.
Mitsubishi on Apple Devices
Visit the iTunes store for a free app
that turns your Apple iPhone, iPad,
or iTouch into a second remote
control for the TV.
Picture shortcuts
The TOOLS Key and Menu
Sound shortcuts
Device-Specific Shortcuts
Availability varies, depend-
ing on equipment features
and setup.
Press the TOOLS key to see the Tools menu. Press
number keys to activate shortcuts. Your Tools menu
may differ from the sample, depending on your setup.
TV
PICTURE SOUND
•
Shortcuts specific to the current device are in the
third column.
3 CC. Turns closed captions
on/off (ANT input only)
•
Shortcuts may be available for a CEC-enabled
device. See the supplemental Owner’s Guide at
Sample Tools menu
For assistance call 1(877) 675-2224
1. Basic Setup and Operation
9
First-Time Power-On
1. Install batteries in the remote control. See page 5.
Welcome Screen Energy Options
2. Aim the emitter (bulb)
end of the remote control
at the TV and press the
•
Mitsubishi recommends the Home setting,
which uses power within ENERGY STAR
guidelines.
®
POWER key
Welcome screen.
Wait for the
.
•
The Retail setting looks best under the bright
lighting often found in commercial settings.
In this mode, the TV uses power in excess of
ENERGY STAR guidelines.
3. If you wish to change the
menu language to Español,
This table compares energy choices offered in the
Welcome screen.
press and press ENTER
.
Home
Bright
Retail
4. Press to move to the
energy-mode selections.
Select Home.
Picture Mode
Super Brilliant
Ambient Light
Sensor Sensitivity
Maximum Off
5. Press to highlight EXIT.
Press ENTER to clear the menu.
Use the Picture > Video menu to change the
Picture Mode. Use the Setup > Energy menu to
control sensitivity of the Ambient Light Sensor.
Setting Up and Using TV Inputs
4. Highlight Ant Air if connected to an
over-the-air antenna. Highlight Ant
Cable for service over direct cable
(no cable box). Press ENTER to add a
check.
The ANT (Antenna) Input
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 16.
You must perform a channel scan to enable recep-
tion of digital channels. If you skip this step, the TV
can receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in your area. Note: Direct cable
service will not include scrambled or premium chan-
nels.
5. Select the scan type.
•
•
For first-time setup, highlight All channels.
To scan for channels not already in memory,
highlight Add only new channels. Press
ENTER to add a check.
Memorizing Channels with Channel Scan
6. Highlight Scan and press ENTER
.
Channel memorization may take up
to 15 minutes to complete.
1. Power on the TV.
2. Press MENU and open the Setup > Channel menu.
To stop channel memorization before completion,
press CANCEL
.
At any time after Channel Scan,
•
Use the Setup > Channel > Edit menu to add or
delete individual channels to or from memory.
Start channel memorization from the Setup > Channel
menu.
•
Repeat the All channels scan if you reposition the
antenna or move the TV to a new geographic area
with a different channel line-up.
3. Press to enter the menu.
For assistance call 1(877) 675-2224
10
1. Basic Setup and Operation
Setting Up and Using TV Inputs, continued
More About the Input Selection Menu
Setting Up Inputs with Auto Input Sensing
Learn more about Auto Input Sensing on page 27.
•
To assign helpful names to the icons, see the
Inputs > Name menu.
1. Power on the TV.
2. Power on the devices to ensure detection.
•
To remove unwanted Antenna or HDMI device icons
from the Input Selection menu, see the Inputs >
Name menu.
3. Connect one device to the TV, making note of the
TV input jack.
•
To rearrange the icons, use the Inputs > Order
The TV will display the New Device Found screen if
menu.
the connection type is detectable.
Detailed information on using these menus is in the sup-
4. Highlight the device type in the on-screen list and
press ENTER. The name you select here will appear
in the Input Selection menu.
Watching Broadcast TV
TV Connected to an Antenna or Direct Cable
Service (no cable box)
Note: Perform channel memorization to enable recep-
tion of digital channels. See page 7.
1. Press INPUT to display the Input Selection menu.
2. Highlight the antenna or cable icon and press ENTER
.
Sample New Device Found screen.
Sample Input Selection menu, antenna input selected
5. Press EXIT to close the New Device Found screen.
3. To tune to a channel from the ANT input, use any of
6. Repeat the preceding steps for each additional
these methods.
device you want to add.
•
Enter the channel number using the number
ENTER
Selecting an Input to Watch
keys on the remote control and press
.
For a two-—part digital channel, such as 3-1,
ENTER
press
Press
3
1
.
CANCEL
CH
•
to change channels one channel at
1. Press INPUT
.
a time.
Press and hold
Press to return to the previous channel.
2. Press
input icon.
and to highlight an
CH
•
•
•
to speed through channels.
LAST
Use the Fav (Favorites) feature to tune to up to
nine favorite channels. See page 19.
GUIDE
to display ChannelView channel
•
•
Press
listings. Highlight a channel number, then
press
Sample Input Selection menu, DVD input selected
ENTER
to tune.
Set up ChannelView custom channel banks
3. Press ENTER to switch to the input.
CH
and use the
key to tune within predefined
Note: In most cases, to see a named icon for a con-
nected device (as in the samples), you must first
assign a name either
groups of channels.
•
When the device is first connected and the
New Device Found menu offers a choice
of names.
•
By using the Inputs > Name menu to
assign or change a name at any time after
the TV has detected the connection.
For assistance call 1(877) 675-2224
1. Basic Setup and Operation
11
Basic TV Operation
Picture Settings
Audio Controls
To get the best picture under different viewing condi-
tions, set the Picture Mode first before changing other
video settings.
Controlling Sound Volume
Press VOL to adjust the sound level of
the TV speakers.
1. Press VIDEO.
2. Press until the Picture Mode
option displays.
3. Press to make one of these selections:
Changing Audio Settings (TV Speakers Only)
Name
When to Use
1. Press AUDIO
.
Super
Brilliant
Under retail lighting; not rec-
ommended for home use.
2. Press to display the name of the
adjustment you want.
Brilliant
Game
Under very bright lighting
3. Press
to change.
With gaming consoles (inputs
named Game or PC only)
Using an External Sound System
Bright
For most daytime viewing
For most nighttime viewing
To switch from the internal TV speakers to an external
sound system:
Natural
Cinema
When viewing movies made
for theatrical release; offers
an extended color gamut.
1. Press AUDIO
.
2. Press to display the TV Speakers option.
3. Press to select either On (to hear sound from
the TV speakers) or Off (to hear sound from an
external sound system).
Note: If the picture is too dim for your viewing envi-
ronment, even after changing the Picture Mode,
go to the Setup > Energy menu and set Ambi-
ent Light Sensor Sensitivity to Off.
See page 17 for suggestions on connecting your sound
system to the TV.
4. Press to display the name of another adjustment.
Disconnecting an A/V Receiver
5. Press
to make the adjustment.
When you disconnect an A/V receiver, change the TV
Speakers setting to On to hear sound from the TV
speakers. Use the Sound > Audio > TV Speakers
menu.
6. Wait a few seconds and the display will clear.
More picture adjustments can be found in these menus:
•
•
•
•
Picture > Video
Picture > Picture Plus
Picture > Perfect
HDMI Control (CEC-Enabled HDMI A/V Receiver)
The TV’s remote control may operate some functions
of your HDMI A/V receiver. See the supplemental
Picture > 3D Mode (page 24)
For assistance call 1(877) 675-2224
12
1. Basic Setup and Operation
Basic TV Operation, continued
The FORMAT Key and Picture Shape
Press the FORMAT key
o cycle through picture
shapes for the current
image. The TV will
Sample Uses of the FORMAT Key
You can use the FORMAT key to display the image as originally intended or
to reduce or eliminate black areas at the edges.
t
remember the format you
last used on each input.
Press
For more on TV formats and signal
types, see the supplemental Owner’s
Important
High-definition signal with
Wide Expand mode stretches
the picture sideways to fill the
screen.
Black bars at the edges of
the screen are common in HD
pictures. Black bars are not a
defect of the TV.
squarish 4:3 image embedded.
The image is narrower than the
16:9 screen; unused areas at
the sides are filled with black.
•
Broadcasters add black bars
to fill the 16:9 screen area while
preserving the original aspect
ratio of older material not created
for modern HD TVs.
Press
•
Your cable box, satellite receiver,
or other device may also have
controls for altering the shape
of the broadcast picture. If your
device offers output in native
format, try using it with the TV
picture formats.
Standard 2.35:1 anamorphic
DVD image; unused areas at
the top and bottom are filled
with black (letterbox effect).
Zoom mode. The picture fills
the screen. All four edges are
cropped in this mode.
More TV Features
See the supplemental Owner’s Guide at
www.mitsubishi-tv.com for more on these and other
topics.
•
•
Parental controls (Lock menu). Requires first
setting a pass code.
TV Clock (Setup > Clock menu). Set the TV Clock if
you plan to use the TV Timer, ChannelView channel
listings, or the TV’s Lock by Time feature.
•
Changing input names in the Input Selection menu
(Inputs > Name menu)
•
•
•
Viewing digital camera images
HDMI (CEC) control of other A/V devices
Using the TV with a computer
For assistance call 1(877) 675-2224
1. Basic Setup and Operation
13
Status Display
3
4
6
1
Press the INFO key to see
the on-screen status
display. The most
common displays are
shown here.
402-101 KABC
TV-PG DLSV
Monday Night Football
St. Louis vs. Tampa Bay, played in Tampa for
2
5
7
Sample information from the
on-screen status display
8
Sleep 30 min
13
English
Surround
Tuesday 9:10 PM
1080i Standard
9
10
14
INFO
11
12
Antenna
DVD
DVR Game Sat. Rcvr.
1. Current Input. Examples:
About Channel Numbers
2. Audio Indicator. Key:
Channel Numbers for Over-the-Air
Reception or Reception by Direct
Cable
TV speakers
External sound system
Mute
3. Channel number (antenna source only)
Note: All signals are automatically
Digital channel includes major and sub-channel numbers.
4. Digital channel name (if broadcast); antenna source only.
5. V-Chip rating
converted to 1080p for display.
Standard-Definition Analog Channels
•
Antenna source only for digital signal
Cable Reception
Channel 3
•
Antenna or VIDEO composite jack for analog signal
6. Program name (if broadcast); digital antenna source only
Cable
3
7. Program description (if broadcast); digital source, antenna
only. Press the INFO key additional times to see more of the
description.
480i Stretch
Receiving Standard-Definition
Analog Signal (480i)
8. Sleep Timer remaining time
9. Day and time
Standard-Definition Digital Channels
10. Signal type being received. All signals are automatically
converted to 1080p for display. See “Signal Definitions” on
this page.
Over-the-Air
Antenna Reception
Main Channel 7
Sub-Channel 1
11. Screen format in use
Ant
7-1 KABC-SD
12. Program audio indicator (antenna source only)
13. Available language (digital source, antenna only)
14. Signal-strength indicator (digital source, antenna only)
480i Stretch
Receiving Standard-Definition
Digital Signal (SD)
Signal Definitions
High-Definition Digital Channels
480i: Standard-definition, older type interlaced signals from the ANT
composite VIDEO, component Y Pb Pr, or HDMI jacks.
,
Over-the-Air
Antenna Reception
Main Channel 7
Sub-Channel 1
480p: Standard-definition progressive-scan signals on the ANT
component Y Pb Pr, or HDMI jacks.
,
Ant
7-1 KABC-HD
720p and 1080i: High-definition signals received through the ANT,
component Y Pb Pr, or HDMI jacks. These signals are always 16:9
(widescreen), but may contain embedded 4:3 images with sidebars.
1080i Standard
Receiving High-Definition
Digital Signal (HD)
1080p: High-definition signals from a PC, Blu-ray player, or some
satellite and set-top boxes; HDMI inputs only.
For assistance call 1(877) 675-2224
14
1. Basic Setup and Operation
TV Menus
Press MENU on the remote control to open the main
menu. Find detailed descriptions of all menus in the sup-
Inputs
Name Name assignments for TV inputs
Picture
HDMI Setup for HDMI Control (CEC) of exter-
Control nal devices
Video Basic picture settings
Order Setup of icons in the Input Selection
Picture+ Specialized picture controls
menu
Reset Reset of sound and picture adjustments
StreamTV Account deactivation; clears your per-
for the current input
sonal data from the TV.
Perfect Fine-tuning of color settings
Demo Demonstrations of selected TV features
Advanced Highly customized picture adjust-
ments for each input. Mitsubishi
recommends these adjustments be
made only by a trained professional
installer.
Update Instructions for updating TV software.
Lock
3D Mode Setup for 3D viewing. See page 24.
Parental Controls to limit TV use by content
ratings (composite video and antenna
input only)
Sound
Time Setup to lock the TV by time of day. Set
Audio Basic audio settings
the TV clock before using this menu.
Global Settings for the AVR AUDIO OUTPUT
Channel Setup to lock specific channels (antenna
jacks (analog audio output)
input only)
Panel Control-panel lock
Other Controls to limit TV use based on rating
systems that may come into effect in the
future (digital channels on the antenna
input only)
Captions
Settings for closed captions
Setup
Language Menu language
Clock Set the TV clock to use the TV Timer, to
use ChannelView listings, or to lock the
TV by time.
Timer Setup for the TV Timer. The Timer tells
the TV to power on automatically at a
time you set. Set the TV clock before
using the TV Timer.
Channel Setup for a channel scan on the ANT
input; addition to or deletion of channels
from TV memory
Energy Controls for TV energy usage
Network Setup for internet connectivity. See
page 21.
For assistance call 1(877) 675-2224
15
2 TV Connections
Before You Begin
Auto Input Sensing
Picture Quality
The TV’s Auto Input Sensing feature automatically rec-
ognizes many connections and prompts you to identify
the type of device connected. See pages 8 and 27 for
more on Auto Input Sensing.
For best picture quality, route signals directly from the
source device to the TV.
Surround Sound
The TV accepts PCM stereo or Dolby Digital 5.1 over
the ANT and HDMI inputs and passes the audio out on
the DIGITAL AUDIO OUTPUT jack.
Connection Types
Use the connection types available on your input
devices that will give the best video quality. For
example, choose HDMI over component video; choose
component video over composite video.
IMPORTANT
Accessories such as cables, adapters, splitters,
or combiners required for TV connections
are not supplied with the TV. These items are
available at most electronics stores.
Connection Types and Audio/Video Quality
VIDEO QUALITY
AUDIO QUALITY
BEST
GOOD
BEST
GOOD
Component
Video
Composite
Video
Digital
Coaxial Audio
L/R Analog
Audio
HDMI
DVI-to-HDMI
HDMI
Dolby Digital 5.1,
PCM 2.0 (stereo)
Standard-definition
video only
High-definition or standard-definition video
Stereo only
Cable Routing
Press the
release tab
to loosen the
cable tie.
Installing the
cable tie
1
2
Install the cable tie (supplied)
in one of the mounting holes.
Sample cable routing. Secure the cable
bundle with the release tab facing out.
Removing the
cable tie
For assistance call 1(877) 675-2224
16
2. TV Connections
Input and Output Jacks
USBa
Power-only port. Can
supply power to TV
accessories.
HDMI Cable Categories
HDMI cables are available as Standard and
High-Speed types.
•
High-Speed HDMI Cables. Blu-ray
players, newer DVD players, video games,
3D content, and set-top boxes require
High-Speed HDMI cables, suitable for clock
frequencies up to 340 MHz or data rates of
up to 10.2 gigabits per second. Use high-
speed cables for 1080p HD signals carrying
extended color encodings (i.e., 30 or more
bits, also called Deep Color). High-Speed
HDMI cables are also suitable for standard
HDTV signals.
LAN
Ethernet port (page 21)
USB
Note: The upper USB port
can power a TV accessory.
The lower USB port can
accept photo and music
files. See the supple-
mental Owner’s Guide at
•
Standard HDMI Cables. Standard HDMI
cables may be unmarked. They are suitable
for standard HDTV 720p, 1080i, and 1080p
signals with 8-bit color depth. Use Stan-
dard HDMI cables for clock frequencies
up to 74.25 MHz or data rates of up to 2.23
gigabits per second.
HDMI (page 15)
Inputs are
HDMI 1.4a compliant.
DIGITAL AUDIO
OUTPUT
(page 17)
L/R
Analog stereo
audio inputs
DVI/PC INPUT
Audio input (page 16)
Y/VIDEO
Composite video
input (page 16)
Y/VIDEO Pb Pr
Component video
input (page 15)
AVR AUDIO OUTPUT
(page 17)
IR IN
Accepts control signals
from an external control-
ler when set up by your
professional installer.
INPUT 1 INPUT 2
3D GLASSES EMITTER
(page 24)
ANT
Coaxial antenna input
(page 16)
For assistance call 1(877) 675-2224
2. TV Connections
17
H
DMI Device
Y Pb Pr Component Video Device
Examples: HDTV Cable Box, Satellite Receiver,
or DVD/Blu-ray Player
Examples: HDTV Cable Box, Satellite Receiver,
or DVD/Blu-ray Player
Required: HDMI cable.
If your source device has an HDMI output, use the con-
nections for an HDMI device described on this page
instead of component video.
Connect an HDMI cable from the TV to the device’s
HDMI output. HDMI-connectable devices provide
video and audio through a single cable.
Required:
Component video cables
RCA-type analog audio cables
Mitsubishi recommends using high-speed HDMI cables
to connect newer devices incorporating HDMI technol-
ogy. See “HDMI Cable Categories” on the opposite page
for more on HDMI cable types.
Note:
•
•
This connection carries high-definition
video signals.
Note:
•
This connection carries high-definition video,
3D video, and Dolby Digital 5.1 audio signals.
To hear digital surround sound from an A/V
receiver, connect the digital audio output
from the device directly to your digital A/V
receiver.
•
This connection supports copy protection
(HDCP).
Audio
cables
TV
panel
HDMI cable
Any device with
HDMI output
Component
video cables
INPUT
1
INPUT
2
Y
Pb
Pr
L
R
AUDIO
CABLE IN or
SATELLITE IN
TV
panel
Any device with com-
ponent video output
Incoming from
cable service or
satellite dish
CABLE IN or
SATELLITE IN
Incoming from
cable service or
satellite dish
For assistance call 1(877) 675-2224
18
2. TV Connections
DVI Video Device
TV
panel
Examples: Computer or Older A/V Device
Note:
•
This connection can carry high-definition video
signals.
Digital DVI
device
•
The HDMI connection supports copy protection
(HDCP).
DVI-to-HDMI
cable
Connect a DVI device (digital only) to one of the TV’s
HDMI input jacks.
DVI OUT
Required:
RCA-type analog audio cables
DVI-to-HDMI cable or DVI/HDMI adapter and HDMI
cable
R
AUDIO
L
Audio
cables
Some devices require a connection using an analog
output first in order to view on-screen menus and to
select DVI as the output. Please review your equipment
instructions for DVI connectivity and compatibility.
Antenna or Cable TV Service
Composite Video Device
Connect the incoming cable to the TV’s ANT input.
Reception over direct cable (no box) is limited to non-
scrambled analog and digital channels.
VCR or other device with composite video
output
Note: This connection does not support high-defini-
tion video signals.
Required:
Cable TV
service
UHF/VHF
Composite video cable (usually yellow)
RCA-type analog audio cables
antenna
TV panel
VCR or other device with
composite video output
AUDIO OUT
COMPOSITE
VIDEO OUT
L
R
or
or
Audio
cables
Not recommeded.
Other connection
types provide better
quality audio and
video.
Older
cable
box
INPUT
1
INPUT
2
IN
OUT
Composite
video cable
TV panel
For assistance call 1(877) 675-2224
2. TV Connections
19
A/V Receiver with Coaxial or Analog Output
A/V Receiver with HDMI Output
Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on the ANT input or devices con-
nected directly to the TV, you must use one of the con-
nections shown below.
Required: HDMI cable
This option allows you to view and hear content from
devices connected to an A/V receiver. The A/V receiver
can send audio and video to the TV over a single HDMI
cable.
The TV makes all incoming audio available in both
digital and analog formats:
You can add an optional audio connection from the
TV’s audio output. The optional audio connection
allows you to hear, through the A/V receiver, devices
connected to the TV only, e.g., an antenna on the ANT
input.
•
Analog incoming audio is available as output in
digital stereo format on the DIGITAL AUDIO OUTPUT
jack and as analog stereo on the AVR AUDIO
OUTPUT jacks.
See page 9 for tips on using an external sound system.
•
Digital incoming audio is available as analog output
on the AVR AUDIO OUTPUT jacks and as digital
audio on the DIGITAL AUDIO OUTPUT jack.
If your A/V receiver converts
Cable box
DVD
all video signals for output
on HDMI, you can use any
connection types from
See page 9 for tips on using an external sound system.
VCR
external devices (content
can be HD or SD video).
player
Digital coaxial
cable (for a digital
A/V receiver)
HDMI
OUT
DIGITAL
AUDIO IN
A/V receiver
with HDMI
output
OPTICAL
HDMI
cable
COAXIAL
INPUT
TV
Optional digital
audio connection
INPUT
1
INPUT
2
A/V receiver
back panel
Stereo analog cables
(for an analog A/V receiver)
TV
Note:
•
On rare occasions, the audio portion of an
HDMI signal may be copy-restricted and
cannot be output from the TV as a digital signal.
To hear these copy-protected signals through
the A/V receiver, use the connection for an
analog A/V receiver.
•
Check the A/V receiver’s Owner’s Guide for
information concerning use of the A/V receiv-
er’s digital input.
For assistance call 1(877) 675-2224
20
2. TV Connections
VCR or DVD Recorder to an
Antenna or Wall Outlet Cable
Required:
•
Video cables
Component video cables (red/blue/green)
-
Audio
cables
or
-
Composite video cable (usually yellow)
•
•
•
RCA-type analog audio cables
Two-way RF splitter
Two coaxial cables
Composite
video cable
Note:
•
•
Use composite video only if component
video or HDMI are unavailable. A
composite video connection cannot carry
high-definition video signals.
INPUT
1
INPUT
2
If your recording device has an analog-only
tuner, you must use a digital converter box
to enable recording of digital broadcasts.
TV
Component
video cables
or
ANTENNA
IN
L
R
COMPOSITE
VIDEO OUT
COMPONENT
VIDEO OUT
AUDIO OUT
DVD Recorder or VCR
RF Splitter
Incoming
cable
For assistance call 1(877) 675-2224
21
3TV Features
The FAV key gives you quick access to favorite program
sources. Sources can be channels from the ANT input
or devices connected to the TV. You can store up to
nine favorites.
FAV (Favorites)
Sleep Timer
The Sleep Timer turns the TV off after the length of time
you set. To set the TV to turn on at a certain time of
day, see the Setup > Timer menu.
Setting the Sleep Timer
1. Press SLEEP
.
2. Press SLEEP additional times to increase the time in
30-minute increments up to the maximum of 120
minutes.
3. Press EXIT or wait five seconds without pressing any
Sample Favorites menu. Switch to favorite channels or
inputs using number keys.
keys for the message to clear.
Viewing or Changing the Sleep Timer
1. Press INPUT and switch the TV to the input
you want to add. If adding a channel, switch
to the ANT input and tune to the channel.
1. Press SLEEP to display the on-screen message.
2. Press SLEEP additional times to change the time
before the TV powers off. To cancel the Sleep
Timer, press SLEEP repeatedly until OFF is dis-
played.
2. Press the FAV key.
3. Move the highlight to the number position
you want to assign to the channel or input.
4. Press ENTER
.
1. While watching TV, press the FAV key.
2. In the Favorites menu, highlight the channel
or input you want to remove.
3. Press CANCEL
.
1. While watching TV, press the FAV key.
2. Press the number key for the channel or
input you want.
For assistance call 1(877) 675-2224
22
3. TV Features
ChannelView Channel Listings
ChannelView Custom Channel Banks
ChannelView displays program descriptions sent by broad-
casters. This information may be unavailable in some
areas. In addition, many cable companies do not send
program information with every digital channel. In such
cases, ChannelView cannot display channel information.
About ChannelView
ChannelView™ shows memorized channels on the ANT
input. It displays channel names and program information
for digital channels. No program information is displayed for
analog channels.
Select a channel bank to customize.
1. Press GUIDE to display ChannelView.
2. Press MENU to move the highlight to the bank
header.
ChannelView allows you to set up three banks of custom chan-
nels for convenient access. You can save groups of channels
by content (e.g., news, sports, children’s programming) or by
TV user.
3. Press
to select Bank 1, 2, or 3.
4. With the bank name highlighted, press ENTER to
enter setup mode where you can select channels to
include in the bank.
Note: You must first set the TV Clock to receive
ChannelView listings. Use the Setup > Clock menu.
Task
Action
Move between banks
Press
.
Move into the channel list Press
.
Add or delete a channel
from the bank
•
Highlight the channel
and press ENTER. A
check indicates the
channel has been
added.
•
Press ENTER again to
clear the check and
remove the channel.
ChannelView, “All” tab. Programs are listed on the right.
Using ChannelView Listings
Remove all channels
from the selected bank
Press CANCEL.
Task
Action
Display/hide
Press GUIDE.
Enter or exit setup mode Press MENU.
ChannelView listings
(ANT input only).
5. Press EXIT when finished with setup.
Move through channels
one by one.
Press or
.
Using Custom Channel Banks
Move through channels
quickly.
Press and hold CH.
•
While watching TV, press CH. The TV will tune only
to channels stored in the current bank.
Jump to listings for a
specific channel.
Enter the channel number.
Press CANCEL once to add a
dash; press CANCEL twice to
clear the channel number.
•
To change to a different channel bank:
1. Press GUIDE.
2. Press MENU.
3. Press
4. Press EXIT.
to highlight the desired bank.
Tune to a highlighted
channel.
Press ENTER.
•
To allow tuning to any channel in memory, select
Update program infor-
mation for a highlighted
digital channel.
Press the INFO key (the
screen may briefly go
blank).
the All bank.
Display program descrip-
tions, if available. The
1. Press to move into
the program area.
description will appear at
the bottom of the screen.
2. Press
to move
between programs.
Display more program
description for the current
channel (if available).
Press INFO.
For assistance call 1(877) 675-2224
3. TV Features
23
StreamTV™ Internet
Internet services let you access many popular on-line
applications providing both free and paid content.
Note: From time to time you may notice changes to
the internet interface as new features are added.
Required for StreamTV internet media:
•
Broadband internet service (at least 2 Mbps for SD,
4 Mbps for HD, and 8 Mbps for 1080p HDX)
Category-5 Ethernet cable or a wireless router
Computer access to the websites of content provid-
ers when initial account activation is required for
service.
•
•
Setup > Network, DHCP connection
•
A credit card to cover the cost of paid content.
EXIT
3. Press
to clear the menu.
Manual
Note: Manual setup is available only for a wired con-
nection.
Home Network Setup
Before using StreamTV internet media, you must
connect the TV to the internet using either an Ethernet
cable or a wireless connection as described here.
1. Connect the TV to your network router with a Cat-
egory-5 Ethernet cable (not supplied).
2. In the Setup > Network menu, highlight Manual
ENTER
and press
.
3. Press to move to the Connection Data area.
4. Input the connection data.
Note: Make sure the TV is on any input other than
USB. Press the INPUT key to change.
ENTER
5. After entering connection data, press
to
Wired Ethernet Connection
connect.
DHCP (automatic)
6. Change any of the following if needed:
1. Connect the TV to your network router with a Cat-
•
•
•
Default Gateway
DNS
Subnet Mask
egory-5 Ethernet cable (not supplied).
Ethernet
cable
Wireless Connection
This TV is IEEE 802.11n-compliant and can communi-
cate directly with your wireless router.
Incoming
high-speed
TV
internet
service
1. Disconnect the Ethernet cable if present.
2. Open the Setup > Network menu. After a few
moments, detected networks will appear listed on
the screen in order of signal strength.
Internet
router or
modem
2. Open the Setup > Network menu to review set-
tings.
Setup > Network menu, wireless connection
For assistance call 1(877) 675-2224
24
3. TV Features
StreamTV™ Internet, continued
3. Highlight the desired network and press ENTER to
connect. A check will appear next to the connected
network. Press CH/PAGE to see more networks if the
list fills more than one screen.
Using StreamTV Internet Media
1. After establishing internet connectivity as described
in “Home Network Setup,” page 21, switch the TV to
any input other than USB.
2. Press the INTERNET key to display services.
3. Press ENTER to launch an application.
Troubleshooting
If You Are Unable to Connect to the Internet
•
•
Check all power and data connections.
If you can reach the internet with a computer or
other device on the same internet service used by
the TV, consult the router or modem owner’s guide
for reset instructions.
Setup > Network menu after connecting. The active
network is checked and connection data displays.
4. If connecting to a secure network, enter the
network key or password when prompted. Special
remote control keys you may need:
•
If you cannot reach the internet, contact your
service provider. You may be asked for network
information such as the TV’s IP address. Go to the
Setup > Network menu to see connection data.
Key
Use for
For Further Assistance
1
Digit 1 and special characters
If you are having trouble connecting your TV or access-
ing internet applications, contact Mitsubishi Customer
Care at 1 (877) 675-2224.
! @ # $ % ^ * _ - + = . SPACE ?
CANCEL
•
Clears the password box of an old
entry from a prior session.
•
Deletes one character during pass-
word entry.
Toggle between upper and lower case
5. Press ENTER to connect.
Note: If you notice RF interference from the TV’s inter-
nal network transmitter, turn off the transmitter.
Open the Setup > Network menu. Select Off
and press ENTER
.
To reconnect later, open the Setup > Network
menu, highlight the network, and press ENTER
.
For assistance call 1(877) 675-2224
3. TV Features
25
StreamTV™ Internet, continued
VUDU
For a list of routers and switches recommended for
use with VUDU services, see the Support > FAQ
section at VUDU.com.
Internet services provided by VUDU Apps let you
™
access many popular on-line applications. In addition
to free content, VUDU’s movie service lets you buy and
to learn more about available movie titles, prices, and
services offered.
Once your account is activated, you can rent and buy
movies using only the TV and the TV’s remote control.
If you are having difficulty with your VUDU
account, contact VUDU Customer Care at
Getting Started with VUDU Movies
1. After establishing internet connectivity as described
in “Home Network Setup,” page 21, switch the TV to
any input other USB.
Other VUDU Support
2. Press the INTERNET key to display services from
Reset your VUDU
account password
Using a computer, go to
requires access to e-mail).
VUDU Apps.
3. Select the VUDU movie service.
4. Browse the VUDU movie catalog and offerings.
5. When you are ready to rent or buy a movie, you
will be prompted to activate your VUDU account.
Follow the on-screen instructions and use a com-
credit card is required for activation.
Reset your parental
controls pass code
Call VUDU Customer Care at
1-888-554-VUDU (8838).
Using VUDU Apps and VUDU Movies
Navigate VUDU’s menus with the keys on the TV’s
remote control. Browse the movie catalog, watch
movie previews, set parental controls, and rent or buy
movies.
•
Key functions vary according to context
and may change with newer versions of
VUDU.
TOOLS. Use the Tools menu to perform A/V reset
while in VUDU movies or some VUDU Apps.
•
Some VUDU screens include instructions
identifying available key functions.
LAST. Goes to a previous screen.
CANCEL. Usually acts like the backspace key
during text entry.
LAST
CH/PAGE Jumps to the previous or next page of
menu items.
.
TOOLS
INTERNET
INTERNET. Displays the VUDU Apps internet
menu. Switch the TV to any input other than
USB before connecting to the internet.
ENTER. Confirms a selection.
•
•
Directional navigation
In VUDU Apps, press
more applications.
to display
EXIT. Closes the current screen and goes to a
home screen.
GUIDE. In some contexts, returns to the
VUDU home menu
.
Playback keys.
INFO. In VUDU’s movie service, displays
more options for the current selection if
available.
F1. Displays a VUDU help menu if available.
F2. Displays the VUDU system menu if
available.
For assistance call 1(877) 675-2224
26
3. TV Features
3D Video
Initial Setup
To display 3D content, your Mitsubishi TV requires:
1. If your 3D glasses came with a synchronization emitter,
connect the unit to the 3D GLASSES EMITTER jack.
Place the emitter at the front of the TV where there is a
clear path to the glasses.
•
Active-shutter 3D glasses compatible with any one
of the following:
-
-
The TV’s internal emitters
A matching external synchronization emitter
connected to the TV’s back panel
DLP link
Note: No emitter is required if using the TV’s internal
-
emitters or DLP Link.
Glasses compatible with the TV’s internal emitters
are:
-
XPAND model 3DG-X103 IR glasses made for
Mitsubishi 3D TVs
-
XPAND model X103 Universal IR glasses
Connecting an
external emitter
For more information, visit the 3D TV page at
2. Power on the TV and the source device.
3. Connect the source device to the TV’s HDMI input.
4. When the New Device Found screen displays,
•
A compatible 3D source device connected to the
TV via HDMI or StreamTV internet and outputting a
3D signal in one of these formats:
name the input.
-
-
-
Frame Packing 1080p/24-Hz or 720p/60-Hz
Top-Bottom 1080p/24-Hz or 720p/60-Hz
Side-by-Side format, 1080p, 24/30/60-Hz;
720p, 60-Hz
Checkerboard format, 1080p, 60-Hz; (lower resolu-
tions may be supported but will not fill the screen)
5. Press EXIT to close the New Device Found screen.
Notes on the TV’s Internal Emitters
-
If using glasses
compatible with the TV’s
internal IR emitters, keep
a clear path from the
Internal IR
Emitters for 3D
Glasses
Off
•
glasses to the emitter.
POWER
Turns off 3D images; displays 3D content
as 2D (you may see two images).
Restores normal TV adjustment options
when viewing an ordinary 2D signal.
16 ft.
Effective range of the
emitters in the vertical
and horizontal planes
•
20°
25 ft.
Automatic
20°
•
Switches the TV to 3D mode and selects the
correct 3D format when the TV detects a 3D
signal from an HDMI 1.4a-compliant device.
Automatically switches the TV out of 3D
mode when receiving a normal 2D signal.
16 ft.
•
35°
25 ft.
35°
16 ft.
Choice of Source Formats
If your device is not HDMI 1.4a
compliant, you must choose the
correct setting from this list.
Use the Picture > 3D Mode menu to enable 3D video.
For assistance call 1(877) 675-2224
3. TV Features
27
3D Video, continued
Other Options in the 3D Menu
Glasses The Off settings disable output
Watching 3D Video
Active 3D glasses are required. All glasses in use
at the same time must use the same control type.
Halogen lights, fluorescent lights, or direct sunlight can
interfere with operation of the glasses.
Control Off from the selected emitter. Use Off
Settings in the unlikely event of IR interfer-
ence with other devices.
2D+ Depth When selected, generates a simu-
lated 3D image from an ordinary
2D image. Requires use of active-
shutter 3D glasses.
1. Switch the TV to the 3D video device. Press INPUT
then highlight the icon for the 3D video device. Press
ENTER
.
Note: Before watching 3D images from an internet
source, it is important to establish the internet
connection first before enabling 3D mode.
2. Press MENU and select the Picture > 3D Mode menu.
3. For Source Format, select Automatic and press
Notes on Using 3D Video Settings
3D signals and 3D settings affect some TV functions.
Switch to a non-3D source to regain full TV operation.
ENTER. Press EXIT to close the menu.
•
If the image looks correct, the device is HDMI
1.4a compliant; always keep the setting at
Automatic for this device.
If Source Format is set to Automatic or one of the
named 3D formats OR Source Format is set to Off and
the 3D video source is HDMI 1.4a compliant (picture may
appear as 2D), the following limitations apply:
•
For non-compliant 3D sources, open the
Picture > 3D Mode menu and select a source
format based on how the picture looks:
•
Picture adjustments are limited. To make picture
adjustments while watching normal 2D images from
the device, temporarily set Source Format to Off to
make the full range of adjustments accessible.
Side by Side
Two images, screen
split vertically
•
While receiving a 3D signal,
-
-
The FORMAT key is disabled.
The INTERNET key is disabled.
Top/Bottom
Two images, screen
split horizontally
Checkerboard
Blurry double image
(always required for
checkerboard signals)
4. Press EXIT to close the menu.
5. If the image does not appear correct (e.g., objects
appear to be moving in instead of out), open the
Picture > 3D Mode menu. Highlight the Reverse
setting for the current control type and press ENTER
to add a check.
6. When finished watching 3D video:
•
If your 3D video device is HDMI1.4a compliant,
keep the setting on Automatic.
•
If you manually selected a source format in the
Picture > 3D menu, open the menu again and
select Automatic or Off.
For assistance call 1(877) 675-2224
28
3. TV Features
3D Video, continued
3D Safety Requirements
•
3D Glasses are NOT designed as sunglasses or safety
glasses and do not provide protection. 3D glasses should
be worn only when viewing 3D material.
Do not wear the wireless glasses in any situations that
require unimpaired visual perception.
Do not use the glasses where loss of balance or limiting your
field of vision may be dangerous to you.
Do not use near staircases, ledges or balconies. You may risk
falling during or after use.
•
•
Epilepsy
Children under the age of 5 should not view 3D pro-
gramming.
WARNING! IF YOU OR ANY MEMBER OF YOUR FAMILY
HAS A HISTORY OF EPILEPSY, CONSULT A PHYSICIAN
BEFORE USING 3D VIDEO OR GAME PRODUCTS.
A small percentage of the population may experience epileptic
seizures when viewing certain types of TV images or video
games that contain flashing patterns of light.
Under normal conditions, 3D viewing is safe for your movies
or games. Some people may experience discomfort, however.
To minimize the potential for experiencing visual problems or
any adverse symptoms:
•
Read and follow any and all safety warnings that accom-
pany your 3D glasses or 3D source devices.
Maintain a distance of no less than 2 to 2.5 times the
screen height measurement away from the display.
Viewing from too short a distance can strain your eyes.
Take regular breaks, at least 5 minutes after every hour of
3D viewing.
The following people should consult a physician before viewing
3D Games or Video:
•
•
Anyone with a history of epilepsy, or who has a family
member with a history of epilepsy
•
Anyone who has ever experienced epileptic seizures or
sensory disturbances triggered by flashing light effects.
•
WARNING! SOME LIGHT PATTERNS MAY INDUCE SEI-
If you experience any of the following symptoms, discontinue
3D viewing until the symptoms go away:
ZURES IN PERSONS WITH NO PRIOR HISTORY OF EPI-
LEPSY. DISCONTINUE 3D VIEWING IF YOU EXPERIENCE
ANY OF THE FOLLOWING SYMPTOMS:
•
•
•
•
nausea, dizziness, or queasiness
headache, or eyestrain
blurry vision
•
•
•
•
•
Involuntary movements, eye or muscle twitching
Muscle cramps
Nausea, dizziness, or queasiness
Convulsions
Disorientation, confusion, or loss of awareness of your
surroundings
double vision that lasts longer than a few seconds
Do not engage in any potentially hazardous activity (for
example, driving a vehicle) until your symptoms have com-
pletely gone away. If symptoms persist, discontinue use and
do not resume 3D viewing without discussing your symptoms
with a physician.
Notice Concerning Format Compatibility
The Mitsubishi TVs will support the mandatory HDMI
In all cases: (1) 3D sources must connect to the TVs
using the HDMI inputs or via StreamTV™ Internet Media;
and (2) Active Shutter 3D glasses that match the TV’s
internal synchronization emitter, or Active Shutter 3D
glasses with their own external matching synchroniza-
tion emitter connected to the rear of the TV or DLP Link
Active Shutter 3D glasses are required in order to view
3D content.
1.4a 3D signals intended for the United States. Spe-
cifically, the TVs will support the 3D signals known as
Frame Packing 1080p/24Hz and 720p/60Hz (primar-
ily from Blu-ray players and gaming consoles), Side-
by-Side in 1080i/60Hz, 1080p/24Hz/30Hz/60Hz and
720p/60Hz, Top/Bottom in 1080p/24Hz and 720p/60Hz,
and Checkerboard 1080p/60Hz. However, there may be
some 3D sources that are not compatible with the TVs.
For assistance call 1(877) 675-2224
Appendices
29
Appendix A: Auto Input Sensing
About Auto Input Sensing
This TV’s Easy Connect™ Auto Input Sensing feature
detects the following connections automatically:
Tips on Auto Sensing
•
•
Choose a different name for each input.
•
•
•
Analog video jacks
The antenna (ANT) input is never detected. It can
HDMI inputs (when powered on)
USB device containing photo and music files (JPG
and MP3 formats).
be turned off in the Inputs > Name menu.
•
•
•
Change the device type displayed in the Input
Selection menu by using the Inputs > Name
menu.
Auto Input Sensing for Most Devices
Some HDMI devices can automatically tell the TV
what name to use in the Input Selection menu
and you will be unable to change the name.
When you first connect a device, the TV will:
a. Detect the connected device and automati-
cally switch to it.
b. Prompt you to identify the device type.
c. Repeat these steps for other newly detected
devices.
The TV is unable to detect a new connection if the
current input is USB or internet. Switch to a dif-
ferent input before connecting.
Reactivating Auto Input Sensing for an HDMI Input
When You First Connect a Device
After you disconnect an HDMI device, Auto Input
Sensing is temporarily disabled and the disconnected
device still appears in the Input Selection menu.
•
Most Device Types. Select the device type from
the on-screen list. The device type you select here
will appear as an icon in the Input Selection menu.
Perform these steps:
•
A/V Receiver. For an HDMI-equipped A/V
receiver, select AVR from the list of device types if
the A/V receiver is not recognized automatically.
1. Power off the device.
2. Disconnect the HDMI cable.
•
HDMI CEC Devices Compatible with the
TV’s HDMI Control Feature. Compatible
CEC-enabled HDMI devices are often recognized
automatically by the TV. HDMI Control may allow
you to control some functions of a CEC-enabled
device. See the supplemental Owner’s Guide at
3. Press MENU on the TV remote control to enter the
TV main menu.
4. Go to Inputs > Name.
5. Highlight the HDMI input name and press ENTER to
select Delete.
6. Press EXIT to clear the menus.
Inputs > Name menu with Delete selected for
HDMI-3.
New Device Found screen for a device with HDMI
control enabled. Select On if you want to enable the
TV’s HDMI control of the device. In some cases, as
in the example, you will also be prompted to select a
device name.
7. Connect the new device and the New Device
Found screen will display.
For assistance call 1(877) 675-2224
30
Appendices
Appendix B: Troubleshooting
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.
TV Reset Comparison Guide
You can resolve many common TV problems using the
reset functions described in the following table.
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
channel (a channel from the ANT input, a cable box, or
satellite receiver), first check other channels from the
same input before changing settings. If most other
Note
Additional troubleshooting tips are in the supplemen-
Reset Name
Format
When to Use
How to Use
Resulting Action
If the picture shape
seems incorrect, use
the FORMAT key to
change the picture
shape.
Press FORMAT to cycle through the
picture shapes available for the
signal.
The last-used format for the signal
type will be recalled on the input.
Note: Also check the aspect
ratio feature on your cable box or
satellite receiver as this may be
altering the picture.
™
PerfectColor / When the color
1. While viewing the input to reset, All PerfectColor/PerfecTint
™
PerfecTint
Reset
intensities seem out
of balance, use the
PerfectColor/PerfecTint
reset to reset the color
balances to the original
factory settings.
press MENU and go to Picture > sliders are reset to the original
Perfect.
center position. The PefectColor/
PerfecTint settings for other
inputs remain unchanged.
(for the single
2. Press ENTER to display the
current input)
PerfectColor adjustment screen.
3. Press CANCEL to reset the colors.
Both PerfectColor and
PerfecTint are reset at
the same time.
A/V Memory
Reset
(for the single
When audio and/or video 1. While viewing the input to reset, Most Audio and Video settings
settings for a single input
seem incorrect, use A/V
Memory Reset to return
the input to the original
factory settings.
press MENU and go to Picture > for the individual input are reset
Reset.
except for the global settings
for audio Balance, Listen To,
Language, Smooth120 (Smooth
120 Film Motion), and Advanced.
current input)
2. Press to highlight Reset.
3. Press ENTER again to reset.
A/V Reset
(for all inputs)
To reset audio and
video adjustments for
While viewing the TV, press the
control-panel buttons INPUT and
Most Audio and Video settings
are returned to the original
all inputs to the original VOLUME DOWN at the same time for at factory settings, including global
factory settings.
least two seconds.
settings not affected by Picture
> Reset. Settings under Picture
> Advanced are unaffected.
Channel
Memorization
To erase and re-mem- 1. Press MENU and go to Setup >
All previously memorized chan-
nels for the antenna input are
erased and a new set of memo-
rized channels is created. All
channel information in the
FAV menu, ChannelView, and
Channel Lock is deleted. To add
or delete individual channels,
use the Setup > Channel > Edit
menu.
orize channels on the
Channel.
ANT input.
2. Highlight the reception mode,
e.g. Ant Air, and press ENTER
.
3. Highlight All Channels and
press ENTER
.
4. Highlight Scan.
5. Press ENTER to start channel
memorization.
Lock Menu
Pass Code
To change your Lock
menu pass code
Press the
9
and LAST keys simultaneously to temporarily unlock the TV. See
For assistance call 1(877) 675-2224
Appendices
31
Appendix B: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
Control-Panel
Lock Release
To re-enable the
Press and hold the INPUT button on
the control panel for ten seconds. If unlocked if the remote control is
the TV is powered off, you can now
press the POWER button to turn it on.
Allows the control panel to be
control-panel buttons
after activation of the
Control-Panel Lock
misplaced.
System Reset
If the TV does not turn Press and hold the POWER button on The TV will turn off. The green
on or off, does not
respond to the remote
control or control-
panel buttons, or has
audio but no video.
the control panel for ten seconds.
LED will flash quickly for about
one minute. The changes you
made most recently, before using
SYSTEM RESET, may be lost.
TV Reset
To reset all consumer- 1. While viewing the TV, press
The TV will start the initialization
process and then turn off.
The front green LED will start
flashing. All memory and
settings outlined in this Owner’s
Guide will need to be set again.
accessible settings
and all memories to
the original factory
defaults.
MENU to display the TV main
menu.
IMPORTANT:
Use this reset
only if other
troubleshooting
has been unsuc- Use TV Reset if the TV
2. With the main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
3. READ THE ON-SCREEN
WARNING AND INSTRUC-
TIONS.
cessful.
can respond to con-
trols but TV behavior is
abnormal.
•
If you do not wish to use this
reset, press EXIT or MENU to
back out.
CAUTION: All owner-
performed setups and
adjustments will be
erased.
•
If you wish to continue,
press ENTER to erase all
memories and settings.
Service and Customer Support
Service
Customer Support
If you are unable to correct a problem with your
TV, consult Mitsubishi Consumer Relations at
1 (877) 675-2224.
•
•
To order replacement or additional remote controls
1 (800) 553-7278.
,
•
DO NOT adjust any controls other than those
described in this Owner’s Guide or the on-line
supplemental Owner’s Guide.
For questions:
-
-
-
Call Consumer Relations at 1 (877) 675-2224.
E-mail: [email protected]
Website: www.mitsubishi-tv.com
•
DO NOT remove the protective back cover of your TV.
For assistance call 1(877) 675-2224
32
Appendices
Appendix B: Troubleshooting, continued
Common Picture Problems
Symptom
Remarks
1. Picture does not look like a high-defini- Compare the picture to the TV’s test picture (Picture > Picture+ menu)
tion picture.
to check if the source signal is supplying a lesser-quality image.
Not all signals are high-definition signals. To receive high-definition
programming from your cable or satellite provider, you must sub-
scribe to the provider’s high-definition service. Some over-the-air
broadcasts are in high-definition and can be received with a high-
quality antenna suited to your location.
2. TV has sound but no picture.
•
•
•
Press MENU on the remote control. If the menu displays, then
there is a problem with the incoming signal.
Check that all video inputs are plugged in firmly to the correct
input jacks.
Press and hold the POWER button on the control panel for ten
seconds to perform System Reset.
3. A color program appears as a black
and white image, or the colors are dim,
or the screen is black.
•
If using component video, check that the red, green, and blue
input cables are correctly connected to the red, green, and blue
component video jacks.
•
•
If using composite video, check that the incoming cable is con-
nected the TV’s green Y/VIDEO jack.
The PerfectColor color balance has been incorrectly set. Reset
the PerfectColor balance.
4. Picture from an HDMI input is noisy
•
•
Compare the picture to the TV’s test picture (Picture > Picture+
menu) to check the source of the noise.
Upgrade a standard (unmarked) HDMI cable to a high-speed
HDMI cable.
(poor quality).
Network
Symptom
Remarks
I cannot connect the TV to the network. Go the Setup > Network menu. Obtain the TV MAC address and
provide it to the router.
For assistance call 1(877) 675-2224
Appendices
33
Appendix B: Troubleshooting, continued
Front-Panel Indicator Light
POWER
LED Color TV Condition
TV is powered off. Normal operation.
None
TV is powered on. Normal operation.
POWER
Green
Green
TV powered off, auto-on TV Timer is set.
Normal operation. TV can be turned on at any time.
Key
Off
Steady On
TV power just turned on. A picture will appear shortly. Normal operation.
Green
Slow Blinking
Fast Blinking
•
•
•
TV just plugged into AC outlet.
AC power just restored after power failure.
TV is rebooting after power fluctuation or receiving abnormal digital signals from
a digital channel or digital device.
Wait approximately two minutes for blinking to stop before turning on. Normal
operation.
TV may require service.
Red/
•
•
Hold power button on front panel for 10 seconds to reset TV.
Yellow
If LED continues to flash red and yellow after reset, turn off the TV and unplug it
from the AC power source. Wait one minute and then plug the set back in.
If LED continues to flash red and yellow, go to www.mitsubishi-tv.com or call
1 (877) 675-2224 to receive Authorized Service Center information.
•
For assistance call 1(877) 675-2224
34
Trademark and License Information
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Electric Visual Solutions America, Inc. (MEVSA) for all software pre installed and/or provided along with this television
(“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
Software only with the Mitsubishi television model that included this owner’s guide and owned by you.
2. RIGHTS AND LIMITATIONS.
LICENSE GRANT. MEVSA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MEVSA.
Updates. MEVSA may elect, but shall be under no obligation, to provide you with customer support and/or software upgrades,
enhancements, or modifications to the Software. Depending on the Mitsubishi TV model and internet access capability, MEVSA may
directly, or indirectly via third parties, update or change such Software, in whole or in part, at any time and without notice to you.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MEVSA of attorneys’ fees in connection with
any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other
violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This
license is effective until terminated, and will terminate immediately without notice from MEVSA or judicial resolution if you fail to comply
with any provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned
by or licensed to MEVSA. All title and intellectual property rights in and to the content which may be accessed through use of the
Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws
and treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MEVSA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MEVSA.
5.
EXPORT RESTRICTIONS. MEVSA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software
back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development,
or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in
U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S.
federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MEVSA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MEVSA. IN
NO EVENT SHALL MEVSA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MEVSA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MEVSA’S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE
ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MEVSA’s
liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money
paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.
For assistance call 1(877) 675-2224
Trademark and License Information
35
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991
Free Software Foundation, Inc.
675 Mass Ave, Cambridge, MA 02139, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and
change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source
code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”,
below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion
of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is
covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along
with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties
under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these
conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program
is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in them-
selves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on
the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works
based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the follow-
ing:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable
copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the
program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that
is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompa-
nies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of
the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and
will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties
remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its
terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to
these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License
and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those
who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circum-
stances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of
the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reli-
ance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may
add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limita-
tion as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and con-
ditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published
by the Free Software Foundation.
If you are interested in obtaining open source code for this product, please contact Mitsubishi at
1 (800) 332-2119. A nominal handling and mailing charge may apply.
For assistance call 1(877) 675-2224
36
Trademark and License Information
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our
free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM
IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY
TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share
and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work
released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish),
that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: respon-
sibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source
code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires that modified versions be marked as changed, so that
their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ free-
dom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to
prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose computers, but in those that do, we wish to avoid the special
danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a
work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a
private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no
warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or op-
tions, such as a menu, a prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among
developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b)
serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a
major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those
activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For
example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to
require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodi-
fied Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as
provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them
make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus
making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship
with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting
or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered
work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices
stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the
Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:
a)The work must carry prominent notices stating that you modified it, and giving a relevant date.
b)The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact all notices”.
c)You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the
work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
d)If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume
of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclu-
sion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways:
a)Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software inter-
change.
b)Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer
support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium
customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
c)Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code
with such an offer, in accord with subsection 6b.
d)Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need
not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third
party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you
For assistance call 1(877) 675-2224
Trademark and License Information
37
remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e)Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection
6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a
dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common
use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of
whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified
version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is trans-
ferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this
requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User
Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communica-
tion across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and
must require no special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though
they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire
Program remains governed by this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases
when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms:
a)Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
b)Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or
c)Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or
d)Limiting the use for publicity purposes of names of licensors or authors of the material; or
e)Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual
assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along
with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by
the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (includ-
ing any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b)
permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this
License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do
not qualify to receive new licenses for the same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy
likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by
modifying or propagating a covered work, you indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance
by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity
transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to posses-
sion of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this
License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of mak-
ing, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to
grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents
of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for pat-
ent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available
network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3)
arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your convey-
ing the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work
authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this
License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of
your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work
conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license
was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work
so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty
for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and
to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction
through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address
new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version” applies to it, you have the option of following the terms
and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any
version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that ver-
sion for the Program.
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil
liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.
For assistance call 1(877) 675-2224
38
Warranty
®
Mitsubishi LASERVUE Television Limited Warranty
MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC. (“MEVSA”) warrants as follows to the original purchaser
of this television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against
defects arising from improper workmanship and/or material:
a. Parts. All parts (except any software incorporated into this television and Lenticular screen surface) are warranted
for a period of one (1) year from the date of the original purchase at retail. We will repair or replace, at our option, any
defective part without charge for the part. Lenticular (i.e. front picture) screen surface is warranted against defect in
materials and workmanship for a period of thirty (30) days from the date of the original purchase at retail. Parts used
for replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used
for replacement are warranted for the remainder of the original warranty period.
b. Embedded Software. MEVSA warrants that all software developed by MEVSA and incorporated into this television
set (the “Embedded Software”) will perform in accordance with the functional description of Embedded Software in
all material respects, but MEVSA does not warrant that the Embedded Software is error-free. MEVSA also does not
warrant that the Embedded Software will be compatible under HDMI CEC software standards with products pro-
duced by any other manufacturer. The limited warranty contained in this section shall continue for a period of one (1)
year from the date of the original purchase at retail. If, after prompt notice within the warranty period, MEVSA deter-
mines that the Embedded Software has failed to perform in accordance with such functional description in all material
respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software,
then MEVSA shall modify the nonconforming Embedded Software and make available the modified Embedded Soft-
ware at no charge to you, which at MEVSA’s sole discretion may be fulfilled by means of modification or replacement
software contained on a replacement memory card or made available through download via the Internet or email for
Customer installation. The foregoing shall be MEVSA’s sole obligation to you under this limited warranty. All rights
under this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the
terms of the Software License Agreement applicable to this television, and this limited warranty on the Embedded
Software shall be null and void if the Embedded Software is modified or changed in any manner except as specifically
authorized by MEVSA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option the Lenticular
Screen if the surface proves defective. For certain items that are designed to be replaced by the consumer, including
(but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all
other parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge
for one (1) year from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within
the applicable warranty time period.
e. This LASERVUE Television uses a single DLP chip to create the screen image. This technology creates the image
using small dots, or picture elements (pixels). Your LASERVUE TV is manufactured to a high level of performance and
quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, some-
times a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MEVSA warrants only that
the percentage of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct
customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from
your MITSUBISHI dealer, by writing at the address provided below, calling MEVSA at 800-332-2119, or by using the
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center.
If not, you must either deliver your television to an authorized service location at your own expense, or pay for any
travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be
provided without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service.
Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE
OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However,
please return the Owner Registration Card so that we can contact you should a question of safety arise which could
affect you.
For assistance call 1(877) 675-2224
Warranty
39
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where
such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other
than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to
carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged
by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered,
defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage
caused by acts of God or other factors beyond the reasonable control of MEVSA, such as power surge damage
caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the
product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or
signal unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any
other damages arising from product installation, removal from or re-installation into custom installations or on wall
mountings, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharp-
ness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver,
antenna, cable or satellite systems, or service of products purchased or serviced outside the U.S.A. Please consult
the operating instructions contained in the Owner’s Guide furnished with the product for information regarding user
controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MEVSA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of inciden-
tal, special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
Mitsubishi Electric Visual Solutions America, Inc. (MEVSA) Internet Applications Policy
MEVSA Internet Applications affords the opportunity to access third party Internet product offerings or services (“Third Party
Services”) on certain Mitsubishi TVs. The Third Party Services accessible herein are provided as per our agreement with these
third parties. These agreements are subject to change, interruption, suspension (including termination) at any time and for various
reasons. MEVSA makes no warranties or representations that any particular Third Party Service will be accessible, available, func-
tion in any particular manner or function at all.
Internet Access Required for Third Party Services; Updates:
To use these Third Party Services, you must obtain high-speed/broadband access to the Internet (such as DSL, cable or T1 lines),
either directly or through devices that access the Internet and pay any service fees associated with such access. In addition, you
must provide all equipment necessary to make such connection to the Internet including a modem or other Internet access device.
Each individual third party Internet product may require different minimum Internet connection speed. The usability and availably
of a functional Mitsubishi television and its internet connected feature may highly be dependent and varied based on high-speed/
broadband internet access, connection speed, bandwidth, other equipment(s), third party applications, firmware updates and other
factors outside of MEVSA’s control and/or responsibility which may also be independent of the actual operation of the television. It
is further understood that Mitsubishi televisions are integrated with sophisticated technologies (software and hardware) which may
For assistance call 1(877) 675-2224
40
exhibit delayed boot-up/shutdown time and/or interrupted services. You further understand that the Third Party Services specifi-
cations and functionality are constantly evolving and that we may directly, or indirectly via third parties, update or change the Third
Party Services, in whole or in part, at any time and without notice to you. Such updates may be required for you to use certain
aspects of the Third Party services or to continue to connect to the Third Party Services.
Availability of Content on Third Party Services:
MEVSA or said third parties providing Third Party Services reserve the right to delete data from their servers, or prevent access
to their servers or to change data categories, product offerings or service levels for any reason that MEVSA or said third parties
deem sufficient in their sole discretion at any time, without notice. MEVSA may also impose additional or different limits on the use
of or access to certain Third Party Services, in any case and without notice or liability. Some or all of the data or functionality of
the Third Party Services may require additional payment and/or subscription by you. However, in no event will you be charged for
any Third Party Services unless those charges are made known to you in advance. MEVSA makes no warranties or representa-
tions of any kind as to the accuracy, currency, or completeness of any information contained on the data servers of such third party
providers of any Third Party Services. Furthermore, we do not review, control, or endorse the content, products or services of
Third Party Services or their data servers.
THIRD PARTY SERVICES ARE PROVIDED SERVICE “AS IS” AND “AS AVAILABLE,” WITHOUT WARRANTY OF ANY KIND
(INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, NON-INFRINGEMENT, OR FITNESS FOR A PARTICULAR
PURPOSE), TO THE MAXIMUM EXTENT PERMITTED BY LAW. USE OF THE THIRD PARTY SERVICES IS AT YOUR SOLE RISK.
THIS MEANS, FOR EXAMPLE, THAT MEVSA DOES NOT GUARANTEE THAT THE THIRD PARTY SERVICES WILL ALWAYS WORK
PROPERLY OR WORK AT ALL. THIS ALSO MEANS WE DO NOT GUARANTEE THAT THE THIRD PARTY SERVICES, CONTENT
OR PRODUCTS WILL BE FREE FROM VIRUSES, HACKS, OR OTHER POTENTIALLY HARMFUL INTRUSIONS. PLEASE NOTE
THAT SOME STATES DO NOT ALLOW SUCH WARRANTY LIMITATIONS, SO THESE LIMITATIONS MAY NOT APPLY TO YOU.
Third Party Services Content Disclaimer:
Certain Third Party Services may include materials from third parties or links to certain third party data servers. You acknowledge
and agree that MEVSA is not responsible for examining or evaluating the content or accuracy of any Third Party Services, their
data servers or related third-party materials. MEVSA does not warrant or endorse and does not assume and will not have any
liability or responsibility for any third-party materials or web sites, or for any other materials, products, or services of third parties.
Links to Third Party Services and any associated links to other data servers are provided solely as a convenience to you. To the
extent provided, content types or descriptions of Third Party Services provided for convenience, and you acknowledge and agree
that MEVSA does not guarantee their accuracy. You understand that by using any of the Third Party Services, you may encounter
content that may be deemed offensive, indecent, or objectionable, which content may or may not be identified as having explicit
language. Nevertheless, you agree to use the Third Party Services at your sole risk and that MEVSA shall have no liability to you for
content that may be found to be offensive, indecent, or objectionable. You agree that you will not use any third-party materials in a
manner that would infringe or violate the rights of any other party, and that MEVSA is not in any way responsible for any such use
by you.
Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE.
Apple, iPad, iPhone, iTouch, iTunes, are trademarks of Apple Inc., registered in the U.S. and other countries.
®
®
Digital Light Processing and DLP are registered trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
®
ENERGY STAR and the ENERGY STAR mark are registered U.S. marks. ENERGY STAR is a registered mark owned
by the U.S. government.
®
HDMI , the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Imaging Science Foundation Certified Calibration Controls
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
VUDU is a trademark of VUDU, Inc.
™
XPAND, X3D, X4D, X6D, their respective logos and other identifying marks of XPAND and X6D Ltd. are and shall
remain the trade-marks and trade names and exclusive property of X6D Ltd.
“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation.
®
ChannelView™, DeepField™ Imager, Easy Connect™, EdgeEnhance™, LASERVUE , PerfectColor™, PerfecTint™,
Plush 1080p® 5G, StreamTV™, are trademarks of Mitsubishi Electric Visual Solutions America, Inc.
For assistance call 1(877) 675-2224
Website:
E-mail:
Call Consumer Relations for operational or connection assistance at
1 (877) 675-2224
To order replacement or additional remote controls,
or call 1 (800) 553-7278
This manual provides basic connection, setup, and operating instructions. Please visit our website at
features of this TV. Follow the Support link to the Product Documents page.
®
For Your Records
SYSTEM RESET
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
If the TV does not respond to the remote control,
control-panel buttons, or will not power on/off,
press and hold the POWER button on the control
panel for ten seconds.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION
The TV will turn off. Power on the TV and the green
LED will flash quickly for about one minute. Recent
settings changes may be lost.
V46
© 2011 Mitsubishi Electric Visual Solutions America, Inc.
853B740A30
For information on System Reset, please see inside back cover.
© 2011 Mitsubishi Electric Visual Solutions America, Inc.
853B740A30
|