Philips 220C1 User Manual

e-Manual  
Philips LCD Monitor Electronic Users Manual  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/INDEX.HTM [98-06-23 09:36]  
Safety and Troubleshooting Information  
In order to maintain the best performance of your monitor and use it for a longer lifetime,  
please use the monitor in a location that falls within the following temperature and  
humidity ranges.  
❍  
Temperature: 0-40°C 32-95°F  
Humidity: 20-80% RH  
❍  
IMPORTANT: Always activate a moving screen saver program when you leave your  
monitor unattended. Always activate a periodic screen refresh application if your LCD  
monitor will display unchanging static content. Uninterrupted display of still or static  
images over an extended period may cause burn in, also known as after-imagingor  
ghost imaging, on your screen. "Burn-in", "after-imaging", or "ghost imaging" is a well-  
known phenomenon in LCD panel technology. In most cases, the burned inor after-  
imagingor ghost imagingwill disappear gradually over a period of time after the power  
has been switched off.  
WARNING: Severeburn-inor after-imageor ghost imagesymptoms will not  
disappear and cannot be repaired. The damage mentioned above is not covered under  
your warranty.  
Service:  
The casing cover should be opened only by qualified service personnel.  
If there is any need for any document for repair or integration, please contact with your  
local service center. (please refer to the chapter of "Consumer Information Center")  
For transportation information, please refer to "Physical Specifications".  
Do not leave your monitor in a car/trunk under direct sun light.  
Consult a service technician if the monitor does not operate normally, or you are  
not sure what procedure to take when the operating instructions given in this  
manual have been followed.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/safety.htm 第 2 頁 / 共 2 [98-06-23 09:36]  
FAQs (Frequently Asked Questions)  
FAQs (Frequently Asked Questions)  
General FAQs  
Q: When I install my monitor what should I do if the screen shows 'Cannot display this video  
mode'?  
A: Recommended video mode for Philips 22": 1680x1050 @60Hz.  
1. Unplug all cables, then connect your PC to the monitor that you used  
previously.  
2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel  
Window, select the Display icon. Inside the Display Control Panel, select the  
'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the  
slidebar to 1680x1050 pixels (22").  
3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.  
4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at  
1680x1050@60Hz (22").  
5. Shut down your computer, disconnect your old monitor and reconnect your  
Philips LCD monitor.  
6. Turn on your monitor and then turn on your PC.  
Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .  
icm)?  
A: These are the driver files for your monitor. Follow the instructions in your user  
manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .  
icm files) or a driver disk when you first install your monitor. Follow the instructions to  
insert the ( companion CD-ROM) included in this package. Monitor drivers (.inf and .  
icm files) will be installed automatically.  
Q: How do I adjust the resolution?  
A: Your video card/graphic driver and monitor together determine the available  
resolutions. You can select the desired resolution under Windows® Control Panel  
with the "Display properties".  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_faq.htm 第 1 頁 / 共 8 [98-06-23 09:36]  
     
FAQs (Frequently Asked Questions)  
Q: What if I get lost when I am making monitor adjustments?  
A: Simply press the Menu button, the Setup button, then select 'Reset' to recall all of  
the original factory settings.  
Q: What is the Auto function?  
A: The AUTO adjustment key restores the optimal screen position, phase and clock  
settings by pressing of a single button without the need to navigate through OSD  
(On Screen Display) menus and control keys.  
Note: Auto function is available in selected models only.  
Q: My Monitor has no power (Power LED does not light up). What should I do?  
A: Make sure the AC power cord is connected between the monitor and AC outlet,  
and click a key on keyboard/mouse to wake up the PC.  
Q: Will the LCD monitor accept an interlaced signal under PC models?  
A: No. If an Interlace signal is used, the screen displays both odd and even horizontal  
scanning lines at the same time, thus distorting the picture.  
Q: What does the Refresh Rate mean for LCD?  
A: Unlike CRT display technology, in which the speed of the electron beam is swept  
from the top to the bottom of the screen determines flicker, an active matrix display  
uses an active element (TFT) to control each individual pixel and the refresh rate is  
therefore not really applicable to LCD technology.  
Q: Will the LCD screen be resistant to scratches?  
A: A protective coating is applied to the surface of the LCD, which is durable to a  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_faq.htm 第 2 頁 / 共 8 [98-06-23 09:36]  
FAQs (Frequently Asked Questions)  
certain extent (approximately up to the hardness of a 2H pencil). In general, it is  
recommended that the panel surface is not subject to any excessive shocks or  
scratches.  
Q: How should I clean the LCD surface?  
A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use  
isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone,  
hexane, etc.  
Q:Can I change the color setting of my monitor?  
A:Yes, you can change your color setting through OSD control as the following  
procedures,  
1. Press "Menu" to show the OSD (On Screen Display) menu  
2. Press "Down Arrow" to select the option "Color" then press "OK" to enter color  
setting, there are three settings as below.  
a. Color Temperature; The six settings are 5000K, 6500K, 7500K,  
8200K, 9300K and 11500K. With settings in the 5000K range the panel  
appears warm,' with a red-white color tone, while a 11500K  
temperature yields cool, blue-white toning."  
b. sRGB; this is a standard setting for ensuring correct exchange of  
colors between different device (e.g. digital cameras, monitors, printers,  
scanners, etc)  
c. User Define; the user can choose his/her preference color setting by  
adjusting red, green blue color.  
d. Gamma; The five settings are 1.8, 2.0, 2.2, 2.4, and 2.6.  
*A measurement of the color of light radiated by an object while it is being heated.  
This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower  
Kelvin temperatures such as 2004K are red; higher temperatures such as 9300K are  
blue. Neutral temperature is white, at 6504K.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_faq.htm 第 3 頁 / 共 8 [98-06-23 09:36]  
FAQs (Frequently Asked Questions)  
Screen Adjustments  
Q: When I install my monitor, how do I get the best performance from the monitor?  
A:For best performance, make sure your display settings are set at  
1680x1050@60Hz for 22".  
Q: How do LCDs compare to CRTs in terms of radiation?  
A: Because LCDs do not use an electron gun, they do not generate the same amount  
of radiation at the screen surface.  
Compatibility with other Peripherals  
Q: Can I connect my LCD monitor to any PC, workstation or Mac?  
A: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and  
workstations. You may need a cable adapter to connect the monitor to your Mac  
system. Please contact your Philips sales representative for more information.  
Q: Are Philips LCD monitors Plug-and-Play?  
A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, XP  
and Vista.  
Q: What is USB (Universal Serial Bus)?  
A: Think of USB as a smart plug for PC peripherals. USB automatically determines  
resources (like driver software and bus bandwidth) required by peripherals. USB  
makes necessary resources available without user intervention. There are three main  
benefits of USB. USB eliminates "case anxiety," the fear of removing the computer  
case to install circuit board cards -- that often requires adjustment of complicated IRQ  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_faq.htm 第 4 頁 / 共 8 [98-06-23 09:36]  
   
FAQs (Frequently Asked Questions)  
settings -- for add-on peripherals. USB does away with "port gridlock." Without USB,  
PCs are normally limited to one printer, two Com port devices (usually a mouse and  
modem), one Enhanced Parallel Port add-on (scanner or video camera, for example),  
and a joystick. More and more peripherals for multimedia computers come on the  
market every day. With USB, up to 127 devices can run simultaneously on one  
computer. USB permits "hot plug-in." No need to shut down, plug in, reboot and run  
set up to install peripherals. No need to go through the reverse process to unplug a  
device. Bottom line: USB transforms today's "Plug-and-Pray" into true Plug-and-Play!  
Please refer to glossary for more information about USB.  
Q: What is a USB hub ?  
A: A USB hub provides additional connections to the Universal Serial Bus. A hub's  
upstream port connects a hub to the host, usually a PC. Multiple downstream ports in  
a hub allows connection to another hub or device, such as a USB keyboard, camera  
or printer.  
LCD Panel Technology  
Q: What is a Liquid Crystal Display?  
A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to  
display ASCII characters and images on digital items such as watches, calculators,  
portable game consoles, etc. LCD is the technology used for displays in notebooks  
and other small computers. Like light-emitting diode and gas-plasma technologies,  
LCD allows displays to be much thinner than cathode ray tube (CRT) technology.  
LCD consumes much less power than LED and gas-displays because it works on the  
principle of blocking light rather than emitting it.  
Q: What differentiates passive matrix LCDs from active matrix LCDs?  
A: An LCD is made with either a passive matrix or an active matrix display grid. An  
active matrix has a transistor located at each pixel intersection, requiring less current  
to control the luminance of a pixel. For this reason, the current in an active matrix  
display can be switched on and off more frequently, improving the screen refresh time  
(your mouse pointer will appear to move more smoothly across the screen, for  
example). The passive matrix LCD has a grid of conductors with pixels located at  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_faq.htm 第 5 頁 / 共 8 [98-06-23 09:36]  
 
FAQs (Frequently Asked Questions)  
each intersection in the grid.  
Q: What are the advantages of TFT LCD compared with CRT?  
A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized  
electrons on fluorescent glass. Therefore, CRT monitors basically operate with an  
analog RGB signal. A TFT LCD monitor is a device that displays an input image by  
operating a liquid crystal panel. The TFT has a fundamentally different structure than  
a CRT: Each cell has an active matrix structure and independent active elements. A  
TFT LCD has two glass panels and the space between them is filled with liquid  
crystal. When each cell is connected with electrodes and impressed with voltage, the  
molecular structure of the liquid crystal is altered and controls the amount of inlet  
lighting to display images. A TFT LCD has several advantages over a CRT, since it  
can be very thin and no flickering occurs because it does not use the scanning  
method.  
Q: Why is vertical frequency of 60Hz optimal for an LCD monitor?  
A: Unlike a CRT monitor, the TFT LCD panel has a fixed resolution. For example, an  
XGA monitor has 1024x3 (R, G, B) x 768 pixels and a higher resolution may not be  
available without additional software processing. The panel is designed to optimize  
the display for a 65MHz dot clock, one of the standards for XGA displays. Since the  
vertical/horizontal frequency for this dot clock is 60Hz/48kHz, the optimum frequency  
for this monitor is 60Hz.  
Q: What kind of wide-angle technology is available? How does it work?  
A: The TFT LCD panel is an element that controls/displays the inlet of a backlight  
using the dual-refraction of a liquid crystal. Using the property that the projection of  
inlet light refracts toward the major axis of the liquid element, it controls the direction  
of inlet light and displays it. Since the refraction ratio of inlet light on liquid crystal  
varies with the inlet angle of the light, the viewing angle of a TFT is much narrower  
than that of a CRT. Usually, the viewing angle refers to the point where the contrast  
ration is 10. Many ways to widen the viewing angle are currently being developed and  
the most common approach is to use a wide viewing angle film, which widens the  
viewing angle by varying the refraction ratio. IPS (In Plane Switching) or MVA (Multi  
Vertical Aligned) is also used to give a wider viewing angle.  
Q: Why is there no flicker on an LCD Monitor?  
A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_faq.htm 第 6 頁 / 共 8 [98-06-23 09:36]  
FAQs (Frequently Asked Questions)  
different from that of a CRT monitor -- and it has no impact of the ease of viewing.  
Flickering in an LCD monitor relates to usually undetectable luminance caused by the  
difference between positive and negative voltage. On the other hand, CRT flickering  
that can irritate the human eye occurs when the on/off action of the fluorescent object  
becomes visible. Since the reaction speed of liquid crystal in an LCD panel is much  
slower, this troublesome form of flickering is not present in an LCD display.  
Q: Why is an LCD monitor virtually low of Electro Magnetic Interference?  
A: Unlike a CRT, an LCD monitor does not have key parts that generate Electro  
Magnetic Interference, especially magnetic fields. Also, since an LCD display utilizes  
relatively low power, its power supply is extremely quiet.  
Ergonomics, Ecology and Safety Standards  
Q: What is the CE mark?  
A: The CE (Conformité Européenne) mark is required to be displayed on all regulated  
products offered for sale on the European market. This 'CE' mark means that a  
product complies with the relevant European Directive. A European Directive is a  
European 'Law' that relates to health, safety, environment and consumer protection,  
much the same as the U.S. National Electrical Code and UL Standards.  
Q: Does the LCD monitor conform to general safety standards?  
A: Yes. Philips LCD monitors conform to the guidelines of TCO Displays 5.0  
standards for the control of radiation, electromagnetic waves, energy reduction,  
electrical safety in the work environment and recyclability. The specification page  
provides detailed data on safety standards.  
Q: After I change new PC, I found this information on screen, how can I do?  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_faq.htm 第 7 頁 / 共 8 [98-06-23 09:36]  
 
FAQs (Frequently Asked Questions)  
A: Because you activate Theft Deterrence function in SmartControl II. Please contact  
IT manager or Philips Service Center.  
More information is provided in the Regulatory Information section.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_faq.htm 第 8 頁 / 共 8 [98-06-23 09:36]  
Troubleshooting  
Troubleshooting  
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these  
solutions, contact Philips customer service representative.  
Common Problems  
Having this problem  
Check these items  
Make sure the power cord is plugged into the power outlet  
and into the back of the monitor.  
First, ensure that the power button on the front of the monitor  
No Picture  
(Power LED not lit)  
is in the OFF position, then press it to the ON position.  
Make sure the computer is turned on.  
Make sure the signal cable is properly connected to your  
computer.  
No Picture  
Check to see if the monitor cable has bent pins.  
The Energy Saving feature may be activated  
(Power LED is white blinking)  
Screen says  
Make sure the monitor cable is properly connected to your  
computer. (Also refer to the Quick Set-Up Guide).  
Check to see if the monitor cable has bent pins.  
Make sure the computer is turned on.  
The Auto Function is designed for use on standard Macintosh  
or IBM-compatible PCs running Microsoft Windows.  
It may not work properly if using nonstandard PC or video  
AUTO button not working properly  
card.  
Imaging Problems  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_troub.htm 第 1 頁 / 共 3 [98-06-23 09:36]  
       
Troubleshooting  
Press the Auto button.  
Adjust the image position using the Phase/Clock of Setup in  
Display position is incorrect  
OSD Main Controls.  
Check that the signal cable is properly connected to the  
graphics board or PC.  
Image vibrates on the screen  
Vertical flicker appears  
Press the Auto button.  
Eliminate the vertical bars using the Phase/Clock of Setup in  
OSD Main Controls.  
Horizontal flicker appears  
Press the Auto button.  
Eliminate the vertical bars using the Phase/Clock of Setup in  
OSD Main Controls.  
Adjust the contrast and brightness on On-Screen Display.  
(The backlight of the LCD monitor has a fixed life span. When  
the screen becomes dark or begins to flicker, please contact  
your sales representative).  
The screen is too bright or too dark  
If an image remains on the screen for an extended period of  
time, it may be imprinted in the screen and leave an after-  
image. This usually disappears after a few hours  
An after-image appears  
This is characteristic of liquid crystal and is not caused by a  
malfunction or deterioration of the liquid crystal. The after-  
image will disappear after a period of time.  
An after-image remains after the power  
has been turned off.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_troub.htm 第 2 頁 / 共 3 [98-06-23 09:36]  
Troubleshooting  
The remaining dots are normal characteristic of the liquid  
Green, red, blue, dark, and white dots  
remains  
crystal used in todays technology.  
Adjust white "power on" light using the power LED of Setup in  
OSD Main Controls.  
Adjust white "power on" light  
For further assistance, refer to the Consumer Information Centers list and contact Philips customer service  
representative.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_troub.htm 第 3 頁 / 共 3 [98-06-23 09:36]  
Regulatory Information  
Regulatory Information  
Available for selective models  
TCO Displays 5.0 Information  
Congratulations,  
Your display is designed for both you and the planet!  
This display carries the TCO Certified label. This ensures that the display is designed for minimal  
impact on the climate and natural environment, while offering all the performance expected from top  
of the line electronic products. TCO Certified is a third party verified program, where every product  
model is tested by an accredited independent test laboratory. TCO Certified represents one of the  
toughest certifications for displays worldwide.  
Some of the Usability features of the TCO Displays 5.0 requirements:  
Visual Ergonomics  
Good visual ergonomics in order to improve the working environment for the user and to reduce sight and strain problems. Important  
parameters are:  
Light levels without color tint, Uniform color and luminance, Wide color gamut  
Calibrated color temperature and gamma curve  
Wide luminance level, Dark black levels, Low motion blur  
Electrical Safety  
Product fulfills rigorous safety standards  
Emissions  
Low alternating electric and magnetic fields emissions  
Low acoustic noise emissions  
Some of the Environmental features of the TCO Displays 5.0 requirements:  
The brand owner demonstrates corporate social responsibility and has a certified environmental management system (EMAS  
or ISO 14001)  
Very low energy consumption both in on- and standby mode  
Restrictions on chlorinated and brominated flame retardants, plasticizer and polymers  
Restrictions on heavy metals such as cadmium, mercury and lead (RoHS compliance)  
Both product and product packaging is prepared for recycling  
The brand owner offers take-back options  
The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as  
well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT  
equipment in a more user-friendly direction. Our labeling system started with displays in 1992 and is now requested by users and IT-  
manufacturers all over the world.  
For more information, please visit www.tcodevelopment.com  
For displays with glossy bezels the user should consider the placement of the display as the bezel may cause disturbing reflections  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 1 頁 / 共 11 [98-06-24 08:52]  
     
Regulatory Information  
from surrounding light and bright surfaces.  
Recycling Information for Customers  
There is currently a system of recycling up and running in the European countries, such as The Netherlands, Belgium,  
Norway, Sweden and Denmark.  
In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA) to follow the IT  
product recycling management process, detail can be found in web site www.epa.gov.tw  
The monitor contains parts that could cause damage to the nature environment. Therefore, it is vital that the monitor is recycled at  
the end of its life cycle.  
Waste Electrical and Electronic Equipment-WEEE  
Attention users in European Union private households  
This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG  
governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You  
are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To  
determine the locations for dropping off such waste electrical and electronic, contact your local government office, the  
waste disposal organization that serves your household or the store at which you purchased the product.  
Attention users in United States:  
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal  
laws. For the disposal or recycling information, contact www.mygreenelectronics.com or www.eiae.org.  
CE Declaration of Conformity  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 2 頁 / 共 11 [98-06-24 08:52]  
     
Regulatory Information  
This product is in conformity with the following standards  
- EN60950-1:2001 (Safety requirement of Information Technology Equipment)  
- EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)  
- EN55024:1998 (Immunity requirement of Information Technology Equipment)  
- EN61000-3-2:2006 (Limits for Harmonic Current Emission)  
- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)  
following provisions of directives applicable  
- 2006/95/EC (Low Voltage Directive)  
- 2004/108/EC (EMC Directive)  
and is produced by a manufacturing organization on ISO9000 level.  
The product also comply with the following standards  
- ISO13406-2 (Ergonomic requirement for Flat Panel Display)  
- GS EK1-2000 (GS specification)  
- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)  
- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)  
- TCO'03, TCO Displays 5.0 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission, TCO:  
Swedish Confederation of Professional Employees) for TCO versions  
Energy Star Declaration  
This monitor is equipped with a function for saving energy which supports the VESA Display  
Power Management Signaling (DPMS) standard. This means that the monitor must be  
connected to a computer which supports VESA DPMS. Time settings are adjusted from the  
system unit by software.  
VESA State  
ON (Active)  
LED Indicator  
White  
Power Consumption  
< 32 W (typ.)  
Normal operation  
Power Saving  
Alternative 2  
One step  
Sleep  
White Blinking  
Off  
< 0.8 W  
< 0.5 W  
Switch Off  
As an ENERGY STAR® Partner, we have determined that this product meets the  
®
ENERGY STAR guidelines for energy efficiency.  
We recommend you switch off the monitor when it is not in use for a long time.  
Federal Communications Commission (FCC) Notice (U.S. Only)  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 3 頁 / 共 11 [98-06-24 08:52]  
   
Regulatory Information  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by the party responsible for compliance  
could void the user's authority to operate the equipment.  
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.  
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.  
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING  
EQUIPMENT REGULATIONS.  
FCC Declaration of Conformity  
Declaration of Conformity for Products Marked with FCC Logo,  
United States Only  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  
Commission Federale de la Communication (FCC Declaration)  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 4 頁 / 共 11 [98-06-24 08:52]  
 
Regulatory Information  
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de  
class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon  
à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une  
installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences  
qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer  
des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir  
l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la  
cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce  
qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur  
pourrait essayer de corriger la situation en prenant les mesures suivantes:  
Réorienter ou déplacer l'antenne de réception.  
Augmenter la distance entre l'équipement et le récepteur.  
Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.  
Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.  
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de  
conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.  
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.  
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE  
MATERIEL BROUILLEUR DU CANADA.  
EN 55022 Compliance (Czech Republic Only)  
MIC Notice (South Korea Only)  
Class B Device  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 5 頁 / 共 11 [98-06-24 08:52]  
   
Regulatory Information  
Please note that this device has been approved for non-business purposes and may be used in any environment, including  
residential areas.  
Polish Center for Testing and Certification Notice  
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment  
that works together (computer, monitor, printer, and so on) should have the same power supply source.  
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form  
of a fuse with a nominal value no larger than 16 amperes (A).  
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which  
should be located near the equipment and easily accessible.  
A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-  
93/T-42107 and PN-89/E-06251.  
North Europe (Nordic Countries) Information  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 6 頁 / 共 11 [98-06-24 08:52]  
   
Regulatory Information  
Placering/Ventilation  
VARNING:  
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR  
DU STÄLLER DIN UTRUSTNING PÅPLATS.  
Placering/Ventilation  
ADVARSEL:  
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT  
ER NEMT TILGÆNGELIGE.  
Paikka/Ilmankierto  
VAROITUS:  
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI  
IRROTTAA PISTORASIASTA.  
Plassering/Ventilasjon  
ADVARSEL:  
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR  
STØMTILFØRSEL ER LETTE Å NÅ.  
BSMI Notice (Taiwan Only)  
Ergonomie Hinweis (nur Deutschland)  
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 7 頁 / 共 11 [98-06-24 08:52]  
   
Regulatory Information  
Röntgenstrahlen" festgelegten Vorschriften.  
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da  
die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind.  
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß  
1. Reparaturen nur durch Fachpersonal durchgeführt werden.  
2. nur original-Ersatzteile verwendet werden.  
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.  
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem  
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem  
Zeichenkontrast wären die Folge).  
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.  
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß  
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.  
End-of-Life Disposal  
Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to  
increase the amount of reusable materials and to minimize the amount to be disposed of.  
Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer.  
(For customers in Canada and U.S.A.)  
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.  
For additional information on recycling contact www.eia.org (Consumer Education Initiative)  
Information for UK only  
WARNING - THIS APPLIANCE MUST BE GROUNDING.  
Important:  
This apparatus is supplied with an approved moulded 13A  
plug. To change a fuse in this type of plug proceed as  
follows:  
1. Remove fuse cover and fuse.  
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or  
BSI approved type.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 8 頁 / 共 11 [98-06-24 08:52]  
   
Regulatory Information  
3. Refit the fuse cover.  
If the fitted plug is not suitable for your socket outlets, it  
should be cut off and an appropriate 3-pin plug fitted in its  
place.  
If the mains plug contains a fuse, this should have a value  
of 5A. If a plug without a fuse is used, the fuse at the  
distribution board should not be greater than 5A.  
Note: The severed plug must be destroyed to avoid a  
possible shock hazard should it be inserted into a 13A  
socket elsewhere.  
How to connect a plug  
The wires in the mains lead are coloured in accordance  
with the following code:  
BLUE - "NEUTRAL" ("N")  
BROWN - "LIVE" ("L")  
GREEN & YELLOW - "GROUND" ("G")  
1. The GREEN AND YELLOW wire must be connected to  
the terminal in the plug which is marked with the letter "G"  
or by the Ground symbol  
AND YELLOW.  
or coloured GREEN or GREEN  
2. The BLUE wire must be connected to the terminal which  
is marked with the letter "N" or coloured BLACK.  
3. The BROWN wire must be connected to the terminal  
which marked with the letter "L" or coloured RED.  
Before replacing the plug cover, make certain that the cord  
grip is clamped over the sheath of the lead - not simply  
over the three wires.  
China RoHS  
The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by Electronic  
Information Products" or commonly referred to as China RoHS. All products including CRT and LCD monitor which are  
produced and sold for China market have to meet China RoHS request.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-ED...001/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 9 頁 / 共 11 [98-06-24 08:52]  
 
Regulatory Information  
Lead-free Product  
Lead free display promotes environmentally sound recovery and disposal of waste from electrical and  
electronic equipment. Toxic substances like Lead has been eliminated and compliance with European  
communitys stringent RoHs directive mandating restrictions on hazardous substances in electrical and  
electronic equipment have been adhered to in order to make Philips monitors safe to use throughout its life  
cycle.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-E...01/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 10 頁 / 共 11 [98-06-24 08:52]  
 
Regulatory Information  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-E...01/CD-Contents/lcd/manual/ENGLISH/220C1/SAFETY/REGS/REGULAT.HTM 第 11 頁 / 共 11 [98-06-24 08:52]  
Other Related Information  
Other Related Information  
Information for Users in the U. S.  
For units set at 115 V :  
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord  
a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.  
For units set at 230 V:  
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord  
a maximum of 15-feet long and a tandem blade, grounding type attachment plug rated 15 A, 250 V.  
Information for Users outside the U.S.  
For units set at 230 V:  
Use a Cord Set consisting of a minimum 18 AWG cord and grounding type attachment plug rated  
15 A, 250 V. The Cord Set should have the appropriate safety approvals for the country in which  
the equipment will be installed and / or be marked HAR.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/safety/saf_other.htm [98-06-23 09:37]  
       
About This Manual  
About This Manual  
About This Guide  
This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It  
describes the LCD monitor's features, setup, operation and other important information. Its  
contents are identical to the information in our printed version.  
It includes the following sections:  
Safety and Troubleshooting Information provides tips and solutions for common problems  
as well as other related information you may need.  
About This Electronic User's Manual gives an overview of information included, along with  
notation icon descriptions and other documentation for your reference.  
Product Information gives an overview of the monitor's features as well as the technical  
specifications for this monitor.  
Installing Your Monitor describes the initial setup process and gives an overview of how to  
use the monitor.  
On-Screen Display provides information on adjusting the settings on your monitor.  
Customer Care and Warranty contains a list of worldwide Philips Consumer Information  
Centers along with help desk phone numbers and information on the warranty applicable  
to your product.  
Glossary defines technical terms.  
Download and Print Option transfers this entire manual to your hard drive for easy  
reference.  
Notational Descriptions  
The following subsections describe notational conventions used in this document.  
Notes, Cautions and Warnings  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/about/about.htm 第 1 頁 / 共 2 [98-06-23 09:37]  
       
About This Manual  
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic  
type. These blocks contain notes, cautions or warnings. They are used as follows:  
NOTE: This icon indicates important information and tips that help you make  
better use of your computer system.  
CAUTION: This icon indicates information that tells you how to avoid either  
potential damage to hardware or loss of data.  
WARNING: This icon indicates the potential for bodily harm and tells you how  
to avoid the problem.  
Some warnings may appear in alternate formats and may not be accompanied by an icon. In  
such cases, the specific presentation of the warning is mandated by the relevant regulatory  
authority.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/about/about.htm 第 2 頁 / 共 2 [98-06-23 09:37]  
Product Information  
Product Information  
Your LCD monitor  
Congratulations on your purchase and welcome to Philips. To fully benefit from the support that Philips offers, register  
SmartImage  
What is it?  
SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness,  
contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching  
a video, Philips SmartImage delivers great optimized LCD display performance.  
Why do I need it?  
You want a LCD display that delivers optimized display all your favorite types of content, SmartImage software  
dynamically adjust brightness, contrast, color and sharpness in real time to enhance your LCD viewing experience.  
How does it work?  
SmartImage - software based on Philips award-winning LightFrametechnology - analyzes the content displayed on  
your screen. Based on a scenario you select, SmartImage dynamically enhances the contrast, color saturation  
and sharpness of images and video for ultimate display performance - all in real time with the press on a single button.  
How to enable SmartImage?  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 1 頁 / 共 10 [98-06-23 09:38]  
       
Product Information  
1.  
2. Keep press  
Press  
to launch the SmartImage on screen display;  
to toggle between Office Work, Image Viewing, Entertainment, Economy, and Off;  
3. The SmartImage on screen display will remain on screen for 5 seconds or you can also pressOKto make  
confirmation.  
4. When SmartImage is enabled, the sRGB scheme is disabled automatically. To use sRGB you need to  
disable SmartImage with the  
button at the front bezel of your monitor.  
Except using  
key to scroll down, you can also press  
buttons to choose and press OKto confirm selection  
and close the SmartImage OSD.There are five modes to be selected: Office Work, Image Viewing, Entertainment,  
Economy, and Off.  
There are five modes to be selected: Office Work, Image Viewing, Entertainment, Economy, and Off.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 2 頁 / 共 10 [98-06-23 09:38]  
Product Information  
1. Office Work: Enhances text and dampens brightness to increase readability and reduce eye strain. This mode  
significantly enhances readability and productivity when you're working with spreadsheets, PDF files, scanned articles or  
other general office applications.  
2. Image Viewing: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos  
and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors.  
3. Entertainment: Ramped up luminance, deepened color saturation, dynamic contrast and razor sharpness displays every  
details in darker areas of your videos without color washout in brighter areas maintaining a dynamic natural values for the  
ultimate video display.  
4. Economy: Under this profile, brightness, contrast are adjusted and backlighting fine-tuned for just right display of  
everyday office applications and lower power consumption.  
5. Off: No optimization by SmartImage.  
SmartContrast  
What is it?  
Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor's contrast  
ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images  
or dimming backlighting for clear display of images on dark backgrounds.  
Why do I need it?  
You want the very best visual clarity and viewing comfort for every type of content. SmartContrast dynamically  
controls contrast and adjusts backlighting for clear, crisp, bright gaming and video images or displays clear, readable text  
for office work. By reducing your monitor's power consumption, you save on energy costs and extend the lifetime of  
your monitor.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 3 頁 / 共 10 [98-06-23 09:38]  
 
Product Information  
How does it work?  
When you active SmartContrast which will analysis the content you are displaying in real time to adjust colors and  
control backlight intensity. This function can obviously enhance contrast in dynamic for more entertainment fun when  
viewing videos or playing games.  
SmartSaturate  
What is it?  
Smart technology that controls color saturation - the degree to which one on screen color is diluted by neighboring colors -  
to deliver rich and vibrant images for more entertainment fun when you are viewing videos.  
Why do I need it?  
You want rich, vibrant images for more entertainment fun when viewing photos or videos.  
How does it work?  
SmartSaturate dynamically controls color saturation - the degree to which on-screen color is diluted by neighboring colors -  
to deliver rich, vibrant display for more entertainment fun when you are viewing images or videos in your  
display's Entertainment mode and is turned off for top quality display of office application and in the Economy mode to  
reduce power consumption.  
SmartSharpness  
What is it?  
Smart technology that enhances sharpness when you need it for ultimate display performance and more entertainment  
fun when you are viewing videos or photos.  
Why do I need it?  
You want the ultimate in sharpness for more entertainment fun when viewing photos or videos.  
How does it work?  
Smart technology enhances sharpness when you need it for ultimate display performance and more entertainment fun  
when you are viewing videos or photos in the Entertainment mode and is turned off for top quality display of  
office applications and in the Economy mode to reduce power consumptions.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 4 頁 / 共 10 [98-06-23 09:38]  
   
Product Information  
Technical Specifications*  
LCD PANEL  
TFT LCD  
Type  
22" visual  
Screen size  
Pixel Pitch  
0.282 x 0.282 mm  
1680 x 1050 pixels  
R.G.B. vertical stripe  
LCD Panel type  
Anti-glare polarizer, hard coated  
473.76 x 296.1 mm  
Effective viewing area  
SCANNING  
56 Hz-76 Hz  
Vertical refresh rate  
Horizontal Frequency  
30 kHz - 83 kHz  
VIDEO  
165 MHz  
Video dot rate  
Input impedance  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 5 頁 / 共 10 [98-06-23 09:38]  
 
Product Information  
- Video  
- Sync  
75 ohm  
2.2K ohm  
0.7 Vpp  
Input signal levels  
Sync input signal  
Sync polarities  
Separate sync  
Composite sync  
Sync on green  
Positive and negative  
* This data is subject to change without notice.  
Resolution & Preset Modes  
A.  
-
Maximum Resolution  
For 220C1  
1680 x 1050 at 75 Hz (analog input)  
1680 x 1050 at 60 Hz (digital input)  
B. Recommended Resolution  
-
For 220C1  
1680 x 1050 at 60 Hz (digital input)  
18 factory preset modes:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 6 頁 / 共 10 [98-06-23 09:38]  
 
Product Information  
H. freq (kHz)  
31.469  
31.469  
31.469  
35.000  
37.500  
35.156  
37.879  
46.875  
48.363  
60.023  
63.981  
79.976  
55.469  
55.935  
70.635  
70.635  
Resolution  
640*350  
V. freq (Hz)  
70.086  
70.087  
59.940  
67.000  
75.000  
56.250  
60.317  
75.000  
60.004  
75.029  
60.020  
75.025  
59.901  
59.887  
74.984  
60.000  
60.000  
720*400  
640*480  
640*480  
640*480  
800*600  
800*600  
800*600  
1024*768  
1024*768  
1280*1024  
1280*1024  
1440*900  
1440*900  
1440*900  
1680*1050  
1680*1050  
64.674  
66.587  
1920*1080  
60.000  
Automatic Power Saving  
If you have VESA DPMS compliance display card or software installed in your PC, the monitor can automatically reduce  
its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor  
will 'wake up' automatically. The following table shows the power consumption and signaling of this automatic power  
saving feature:  
Power Management Definition  
LED  
VESA Mode  
Active  
Video  
ON  
H-sync  
V-sync  
Power Used  
color  
White  
Yes  
Yes  
< 32 W (typ.)  
White  
Blinking  
Sleep  
OFF  
No  
No  
< 0.8 W  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 7 頁 / 共 10 [98-06-23 09:38]  
 
Product Information  
Switch Off  
OFF  
-
-
< 0.5 W  
Off  
®
®
This monitor is ENERGY STAR compliant. As an ENERGY STAR Partner, we have  
®
determined that this product meets the ENERGY STAR guidelines for energy efficiency.  
Physical Specifications  
-5°+2/-0 ~+ 20°+3/-0  
100 ~ 240 VAC, 50/60 Hz  
32 W* (typ.)  
Tilt  
Power supply  
Power consumption  
0° C to 40° C (operating)  
-20° C to 60° C (storage)  
Temperature  
20% to 80%  
Relative humidity  
50K hours (CCFL 50K hours)  
System MTBF  
* This data is subject to change without notice.  
The native resolution of the monitor is 1680 x 1050. By default, your monitor has 100% brightness (max.), 50% contrast,  
and 6500K color temperature, with a full white pattern.  
Pin Assignment  
1.The digital only connector contains 24 signal contacts organized in three rows of eight contacts. Signal pin assignments  
are listed in the following table:  
Pin  
No.  
Pin  
No.  
Pin  
No.  
Signal Assignment  
Signal Assignment  
T.M.D.S. Data1-  
Signal Assignment  
1
2
3
4
9
T.M.D.S. Data0-  
T.M.D.S. Data0+  
T.M.D.S. Data0/5 Shield  
No connect  
T.M.D.S. Data2-  
T.M.D.S. Data2+  
T.M.D.S. Data2/4 Shield  
No connect  
17  
10 T.M.D.S. Data1+  
11 T.M.D.S. Data1/3 Shield  
12 No connect  
18  
19  
20  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 8 頁 / 共 10 [98-06-23 09:38]  
   
Product Information  
5
6
7
8
No connect  
DDC Clock  
DDC Data  
No connect  
13 No connect  
No connect  
21  
22  
23  
24  
14 +5V Power  
T.M.D.S. Clock Shield  
T.M.D.S. Clock+  
T.M.D.S. Clock-  
15 Ground (for +5V)  
Hot Plug Detect  
16  
2.The 15-pin D-sub connector (male) of the signal cable:  
Assignment  
Assignment  
Pin No.  
Pin No.  
9
Red video input  
DDC + 5 V  
1
2
3
4
5
6
7
8
Green video input/SOG  
Blue video input  
Sense (GND)  
Logic ground  
10  
Ground  
11  
Serial data line (SDA)  
H. Sync / H+V. Sync  
V. Sync  
12  
Cable detect (GND)  
Red video ground  
Green video ground  
Blue video ground  
13  
14  
Data clock line (SCL)  
15  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 9 頁 / 共 10 [98-06-23 09:38]  
Product Information  
Product Views  
Follow the links to see various views of the monitor and its components.  
Physical Function  
Tilt  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/product.htm 第 10 頁 / 共 10 [98-06-23 09:38]  
   
Philips Pixel Defect Policy  
Philips Pixel Defect Policy  
Philips' Flat Panel Monitors Pixel Defect Policy  
Philips strives to deliver the highest quality products. We use some of the industry's most advanced  
manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on  
the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can  
guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with  
an unacceptable number of defects will be repaired or replaced under warranty. This notice explains  
the different types of pixel defects and defines acceptable defect levels for each type. In order to  
qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel  
must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 19"  
XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for certain  
types or combinations of pixel defects that are more noticeable than others. This policy is valid  
worldwide.  
Pixels and Sub pixels  
A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and  
blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub  
pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together  
appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of  
other colors.  
Types of Pixel Defects  
Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel  
defects and several types of sub pixel defects within each category.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/pixel.htm 第 1 頁 / 共 4 [98-06-23 09:38]  
   
Philips Pixel Defect Policy  
Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is,  
a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern.  
There are the types of bright dot defects:  
Two adjacent lit sub pixels:  
- Red + Blue = Purple  
- Red + Green = Yellow  
One lit red, green or blue sub  
pixel  
Three adjacent lit sub pixels  
(one white pixel)  
- Green + Blue = Cyan (Light Blue)  
A red or blue bright dot must be more than 50 percent brighter than neighboring dots  
while a green bright dot is 30 percent brighter than neighboring dots.  
Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That  
is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern.  
These are the types of black dot defects:  
One dark sub pixel  
Two or three adjacent dark sub pixels  
Proximity of Pixel Defects  
Because pixel and sub pixels defects of the same type that are near to one another may be more  
noticeable, Philips also specifies tolerances for the proximity of pixel defects.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/pixel.htm 第 2 頁 / 共 4 [98-06-23 09:38]  
Philips Pixel Defect Policy  
Pixel Defect Tolerances  
In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT  
LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the  
tolerances listed in the following tables.  
BRIGHT DOT DEFECTS  
MODEL  
ACCEPTABLE LEVEL  
220C1  
1 lit subpixel  
3
2 adjacent lit subpixels  
1
3 adjacent lit subpixels (one white pixel)  
Distance between two bright dot defects*  
Total bright dot defects of all types  
0
>15mm  
3
BLACK DOT DEFECTS  
MODEL  
ACCEPTABLE LEVEL  
220C1  
1 dark subpixel  
5
2 adjacent dark subpixels  
3 adjacent dark subpixels  
Distance between two black dot defects*  
Total black dot defects of all types  
2
0
>15mm  
5
TOTAL DOT DEFECTS  
MODEL  
ACCEPTABLE LEVEL  
220C1  
Total bright or black dot defects of all types  
5
Note:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/pixel.htm 第 3 頁 / 共 4 [98-06-23 09:38]  
Philips Pixel Defect Policy  
* 1 or 2 adjacent sub pixel defects = 1 dot defect  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/pixel.htm 第 4 頁 / 共 4 [98-06-23 09:38]  
SmartControl  
SmartControl II (Selective Models)  
Philips SmartControl II  
SmartControl II is monitor-based software with an easy-to-use on-screen graphic interface that guides you through fine-  
tuning resolution, color calibration and other display settings including brightness, contrast, clock & phase, position, RGB,  
white point and - on models with onboard speakers - volume adjustments.  
System support and requirement:  
1. Sytem support: 2000, XP, NT 4.0, XP 64 Edition, Vista 32/64. IE Support 6.0/7.0.  
2. Language support: English, Simplified Chinese, German, Spanish, French, Italian, Russian, Portuguese.  
3. Philips Monitor support DDC/CI Interface.  
Installation:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 1 頁 / 共 17 [98-06-23 09:38]  
       
SmartControl  
Follow the instruction and complete the installation.  
You can lauch after installation complete.  
If you want to launch later, you can either click the shortcut on desktop or toolbar.  
Start to use:  
1. First launch -Wizard  
The first time after installation of SmartControl II, it will automatically go to Wizard for first time launch.  
The wizard will guide you through adjustment your monitor performance step by step.  
You can go to Plug-in menu to launch wizard later on as well.  
You can adjust more options without wizard by Standard pane.  
Wizard Analog Sequence  
Wizard Digital Sequence  
Resolution  
Focus  
Resolution  
Contrast  
Brightness  
Contrast  
Brightness  
White Point (Color Temp)  
Position  
File  
White Point (Color Temp)  
File  
-
-
2. Start with Standard pane:  
Adjust menu:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 2 頁 / 共 17 [98-06-23 09:38]  
 
SmartControl  
Adjust Menu allow you to adjust Brightness, Contrast, Focus, Position and Resolution.  
You can follow the instruction and do the adjustment.  
Cancel prompts user if you want to cancel installation.  
Tab Heading  
Adjust  
Sub Menu  
Brightness  
Display in Analog  
Display in Digital  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Adjust  
Contrast  
Adjust  
Focus (Clock & Clock Phase)  
Position  
Adjust  
No  
Adjust  
Resolution  
Yes  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 3 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
Color menu:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 4 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
Color Menu allow you to adjust RGB, Black Level, White Point, Color Calibration, and  
SmartImage (Please refer to SmartImage section).  
You can follow the instruction and do the adjustment.  
Refer to below table for sub-menu item base on your input.  
Example for Color Calibration  
Tab Heading  
Color  
Sub Menu  
RGB  
Display in Analog  
Display in Digital  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Color  
Black Level  
White Point  
Color Calibration  
Viewing Mode  
Color  
Color  
Color  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 5 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
1. "Show Me" starts color calibration tutorial.  
2. Start - starts the 6-step color calibration sequence.  
3. Quick View loads the before/after images.  
4. To return to Color home pane, click the Cancel button.  
5. Enable color calibration - by default is on. If unchecked, does not allow for color calibration to happen, dimes out start  
and quick view buttons.  
6. Must have patent info in calibration screen.  
First color Calibration Screen:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 6 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
1. Previous button is disabled until the second color screen.  
2. Next goes to the succeeding target (6-targets).  
3. Final next goes File>Presets pane.  
4. Cancel closes the UI and returns to the plug in page.  
SmartImage - Allows user to change setting for better display setting based on content.  
When Entertainment is set, SmartContrast and SmartResponse are enabled.  
Plug-Ins - Asset Management Pane will only be active when selecting Asset Management from the drop-down  
Plug Ins menu.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 7 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
Displays Assent Management information on Managment, Description, Serial Number, Current Timing, Domain Name,  
and Asset Management Status.  
To return to Plug-in home pane select the plug-in tab.  
Plug-Ins - Theft Deterrence Pane will only be active when selecting Theft Deterrence Mode from the drop-down  
Plug Ins menu.  
To enable Theft Deterrence, clicking Enable Theft Mode button brings up the following screen:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 8 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
1. User can enter PIN between 4 and 9 digits numbers only.  
2. After entering PIN, Accept button takes user to the pop-up dialog box on the following page.  
3. Minimum minutes set to 5. Slider set to 5 by default.  
4. Does not require the display be attached to a different host to go into theft mode.  
Once a PIN is entered and accepted, the following dialog box appears:  
Click on No button takes user to the following screen.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU...B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 9 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
Click on Yes button takes user to secure web site landing page.  
After creating PIN, the Theft Deterrence pane will indicate Theft Deterrence Enabled and provide PIN Options button:  
1. Theft Deterrence Enabled is displayed.  
2. Disable Theft Mode opens pane screen on next page.  
3. PIN Options button only available after user creates PIN, button opens secure PIN web site.  
Disable Theft button opens the following pane:  
1. After entering PIN, Accept button disables PIN.  
2. Cancel button opens up main Theft Deterrence pane, displaying Theft Deterrence Disabled. Enable Theft Mode and  
PIN Options buttons.  
3. Entering incorrect PIN results in the following dialog box:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF....0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 10 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
Options>Preferences - Will only be active when selecting Preferences from the drop-down Options menu. On a  
non-supported display capable of DDC/CI, only the Help and Options tabs are available.  
1. Displays current preference settings.  
2. A checked box enables the feature. The check box is a toggle.  
3. Enable Context Menu on desktop is checked (On) by default. Enable Context menu displays SmartControl II selections for  
Select Preset and Tune Display in the desktop right-click context menu. Disabled removes SmartControl II from the right click  
context menu.  
4. Enable Task Tray icon is checked (On) by default. Enable context menu shows the task tray menu for SmartControl II. A right  
click on the task tray icon displays the menu options for Help, Technical Support. Check for Upgrade, About, and Exit.  
When Enable task tray menu is disabled, the task tray icon will only display EXIT.  
5. Run at Startup is checked (On) by default. When disabled, SmartControl II will not launch at start or be in the task tray. The  
only way to launch SmartControll II is either from the desktop short cut or from the program file. Any preset set to run at  
startup will not load when this box is unchecked (Disabled).  
6. Enable transparency mode (Vista, XP, and 2k only). Default is 0% Opaque.  
Options>Input - Will only be active when selecting Input from the drop-down Options menu. On a non-  
supported display capable of DDC/CI, only the Help and Options tabs are available. All other SmartControl II tabs  
are not available.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF....0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 11 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
1. Display the Source instruction pane and current input source setting.  
2. On single input displays, this pane will not be visible.  
Options>Audio - Will only be active when selecting Volume from the drop-down Options menu.  
On a non-supported display capable of DDC/CI, only the Help and Options tabs are available.  
Option>Auto Pivot  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF....0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 12 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
Help>User Manual - Will only be active when selecting User Manual from the drop-down Help menu. On a  
non-supported display capable of DDC/CI, only the Help and Options tabs are available.  
Help>Version - Will only be active when selecting Version from the drop- down Help menu. On a non-  
supported display capable of DDC/CI, only the Help and Options tabs are available.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF....0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 13 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
Context Sensitive menu  
The Context Sensitive menu is Enabled by default. If Enable Context Menu has been checked in the  
Options>Preferences pane, then the menu will be visible.  
The Context Menu has four entries:  
1. SmartControll II - When selected the About Screen is displayed.  
2. Select Preset - Provides a hierarchical menu of saved presets for immediate use. A check mark shows the currently selected  
preset. Facoty Preset can also be called from the drop down menu.  
3. Tune Display - Opens the SmartControl II control panel.  
4. Fly off for SmartImage - Check current settings, Off, Office Work, ImageViewing, Entertainment, Economy.  
Task Tray Menu Enabled  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF....0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 14 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
The task tray menu can be displayed by right-clicking on the SmartControl II icon from the task tray. Left Click will launch  
the application.  
The task tray has five entries:  
1. Help - Access to User Manual file: opnes User Manual file using the default browser window.  
2. Technical Support - displays the tech support page.  
3. Check for Update - takes the user to PDI Landing and checks the user's version against the most current available.  
4. About - Displays detailed reference information: product version, release information, and product name.  
5. Exit - Close SmartControll II. To run SmartControll II again either select SmartControll II from Program menu, double-click the  
desktop PC icon or restart the system.  
Task Tray Menu Disabled  
When the Task Tray is disabled in the preference folder, only the EXIT selection is available. To completely  
remove SmartControll II from the task tray, disable Run at Startup in Options>Preferences.  
Q&A  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF....0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 15 頁 / 共 17 [98-06-23 09:38]  
 
SmartControl  
Q1. I change the monitor on a PC to a different one and the SmartControl becomes un-usable, what do I do?  
A. Restart your PC and see if SmartControl can work. Otherwise, you will need to remove and re-install SmartControl  
to ensure proper driver is installed.  
Q2. The SmartControl functions well at the beginning, but it is not workable, what can I do?  
A. If the following actions were executed, the monitor driver may need to be re-installed.  
Change video graphic adapter to another one  
Update video driver  
Activities on OS, such as service pack or patch  
Run Windows Update and updated monitor and/or video driver  
Windows was booted with the monitor power off or disconnected.  
To find out, please right click My Computer and click on Properties->Hardware-> Device Manager.  
If you see "Plug and Play Monitor" shows under Monitor, then you need to re-install. Simply remove SmartControl and  
re-install it.  
Q3. After installing SmartControl, when clicking on SmartControl tab, nothing shows up after a while or a failure  
message shows, what happened?  
A. It might be your graphic adaptor is not compatible with the SmartControl. If your graphic adaptor is one of the  
above mentioned brands, try to download the most updated graphic adaptor driver from corresponding companiesweb  
site. Install the driver. Remove SmartControl, and re-install it once more.  
If it is still not working, we are sorry that the graphic adaptor is not supported. Please pay attention to Philipsweb site for  
any updated SmartControl driver available.  
Q4. When I click on Product Information, only partial information is shown, what happened?  
A. It might be your graphic card adaptor driver is not the most updated version which fully supporting DDC/CI  
interface. Please try to download the most updated graphic adaptor driver from corresponding companiesweb site. Install  
the driver. Remove SmartControl, and re-install it once more.  
Q5. I forgot my PIN for Theft Deterrence Function. How can I do?  
A. Please contact IT manager or Philips Service Center.  
Q6. In a monitor with the Smartlmage feature, the sRGB scheme of color temperature function in SmartControl is  
not responding, why?  
A. When Smartlmage is enabled, the sRGB scheme is disabled automatically. To use sRGB, you need to  
disable Smartlmage with the  
button at the front bezel of your monitor.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF....0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 16 頁 / 共 17 [98-06-23 09:38]  
SmartControl  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF....0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/product/SMART.HTM 第 17 頁 / 共 17 [98-06-23 09:38]  
Installing Your LCD Monitor  
Installing Your LCD Monitor  
Front View Product Description  
1
To switch monitor's power On and Off  
2
3
To access the OSD menu  
To adjust the OSD menu  
4
5
Change to 4:3 display  
To change the signal input source  
Input  
Automatically adjust the horizontal position, vertical position, phase and  
clock settings / Return to previous OSD level  
6
7
8
To adjust brightness of the display  
SmartImage. There are five modes to be selected: Office Work, Image  
Viewing, Entertainment, Economy, and Off  
Rear View  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/install/install.htm 第 1 頁 / 共 3 [98-06-23 09:39]  
     
Installing Your LCD Monitor  
1
2
3
4
5
6
USB downstream port  
USB upstream port  
VGA input  
DVI-D input (available for selective models)  
AC power input  
Kensington anti-thief lock  
Optimizing Performance  
For best performance, ensure that your display settings are set at 1680x1050, 60Hz.  
Note: You can check the current display settings by pressing the 'OK' button  
once. The current display mode is shown in OSD main controls called  
RESOLUTION.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/install/install.htm 第 2 頁 / 共 3 [98-06-23 09:39]  
 
Installing Your LCD Monitor  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/install/install.htm 第 3 頁 / 共 3 [98-06-23 09:39]  
Connecting to Your PC  
Connecting to Your PC  
Accessory Pack  
Unpack all the parts.  
DVI cable (Optional)  
Power cord  
EDFU pack  
VGA cable (Optional)  
Connecting to Your PC  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF...V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/INSTALL/CONNECT.HTM 第 1 頁 / 共 3 [98-06-23 19:04]  
     
Connecting to Your PC  
1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected  
VGA cable for the first installation.  
*available for selective models  
*available for selective models  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF...V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/INSTALL/CONNECT.HTM 第 2 頁 / 共 3 [98-06-23 19:04]  
Connecting to Your PC  
2) Connect to PC  
(a)  
(b)  
Turn off your computer and unplug its power cable.  
Connect the monitor signal cable to the video connector on the back of your  
computer.  
(c)  
(d)  
(e)  
Connect the USB cable to the USB port of your computer.  
Plug the power cord of your computer and your monitor into a nearby outlet.  
Turn on your computer and monitor. If the monitor displays an image,  
installation is complete.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDF...V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/INSTALL/CONNECT.HTM 第 3 頁 / 共 3 [98-06-23 19:04]  
The Base  
The Base  
Attach the Base Stand  
1) Place the monitor face down on a smooth surface taking care to avoid scratching or  
damaging the screen.  
2) Hold the monitor base with both hands and firmly insert the base stand into the base  
column.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/install/base.htm 第 1 頁 / 共 2 [98-06-23 09:39]  
   
The Base  
Detach the Base Stand  
Place the monitor face on a safe surface, push down on the release button and pull the  
base stand away from the monitor body.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/install/base.htm 第 2 頁 / 共 2 [98-06-23 09:39]  
 
Getting Started  
Getting Started  
Your LCD Monitor :  
Getting Started  
Use the information file ( .inf) for Windows® 98/2000/XP/Vista or later  
The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for  
Windows® 98/2000/XP/Vista. This information file ( .inf) should be installed in order that your  
Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 98/2000/XP/Vista and  
the Plug & Play application can be activated. The installation procedure based on Windows®  
98, 2000, XP and Vista is specified as follows.  
For Windows® 98  
1. Start Windows® 98  
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.  
3. Double click on the 'Display' Icon.  
4. Select the 'Settings' tab then click on 'Advanced...'.  
5. Select the 'Monitor' button, point to 'Change...' then click on 'Next'  
6. Select 'Display a list of all the drivers in a specific location, so you can choose the driver  
you want.' then click on 'Next' and then click on 'Have Disk...'.  
7. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click  
on the 'OK' button.  
8. Click on the 'OK' button then select your monitor model and click on the 'Next' button.  
9. Click on the 'Finish' button then the 'Close' button.  
For Windows® 2000  
1. Start Windows® 2000.  
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.  
3. Double click on the 'Display' Icon.  
4. Select the 'Settings' tab then click on 'Advanced...'.  
5. Select 'Monitor'  
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please  
stop installation.  
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps  
given below.  
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.  
7. Select 'Display a list of the known drivers for this device so that I can choose a specific  
driver', then click on 'Next' and then click on 'Have disk...'.  
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).  
9. Click on the 'Open' button, then click on the 'OK' button.  
10. Select your monitor model and click on the 'Next' button.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/install/gt_start.htm 第 1 頁 / 共 3 [98-06-23 09:40]  
     
Getting Started  
11. Click on the 'Finish' button then the 'Close' button.  
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.  
For Windows® XP  
1. Start Windows® XP.  
2. Click on the 'Start' button and then click on 'Control Panel'.  
3. Select and click on the category 'Printers and Other Hardware'  
4. Click on the 'Display' Item.  
5. Select the 'Settings' tab then click on the 'Advanced' button.  
6. Select 'Monitor' tab  
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please  
stop installation.  
- If the 'Properties' button is active, click on 'Properties' button.  
Please follow the steps below.  
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.  
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on  
the 'Next' button.  
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the  
'Next' button.  
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the  
appropriate drive F: (CD-ROM Drive).  
11. Click on the 'Open' button, then click the 'OK' button.  
12. Select your monitor model and click on the 'Next' button.  
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with  
Windows® XP' message, please click on the 'Continue Anyway' button.  
13. Click on the 'Finish' button then the 'Close' button.  
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties  
dialog box.  
For Windows® Vista  
1. Start Windows® Vista.  
2. Click the Start button; select and click on 'Control Panel'.  
3. Select and click on 'Hardware and Sound'  
4. Choose 'Device Manager' and Click on 'Update device drivers'.  
5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.  
6. Click on 'Update Driver Software'.  
7. Select 'Browse my computer for driver software'.  
8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:  
(CD-ROM Drive:\\Lcd\PC\drivers\).  
9. Click the 'Next' button.  
10. Wait few minutes for installing the driver, and then click 'Close' button.  
If your Windows® 98/2000/XP/Vista version is different or you need more detailed installation  
information, please refer to your Windows® 98/2000/XP/Vista user's manual.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/install/gt_start.htm 第 2 頁 / 共 3 [98-06-23 09:40]  
Getting Started  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/install/gt_start.htm 第 3 頁 / 共 3 [98-06-23 09:40]  
On-Screen Display  
On-Screen Display  
Description of the On Screen Display  
What is the On-Screen Display?  
On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust  
screen performance or select functions of the monitors directly through an on-screen instruction  
window. A user friendly on screen display interface is shown as below :  
Basic and simple instruction on the control keys.  
In the OSD shown above users can press  
the cursor, to confirm the choice or change.  
buttons at the front bezel of the monitor to move  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/osd/osddesc.htm 第 1 頁 / 共 3 [98-06-23 09:40]  
   
On-Screen Display  
The OSD Tree  
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference  
when you want to work your way around the different adjustments later on.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/osd/osddesc.htm 第 2 頁 / 共 3 [98-06-23 09:40]  
 
On-Screen Display  
Resolution notification  
This monitor is designed for optimal performance at its native resolution, 1680X1050@60Hz. When  
the monitor is powered on at a different resolution, an alert is displayed on screen: Use  
1680x1050@60Hz for best results.  
Display of the native resolution alert can be switched off from Setup in the OSD (On Screen  
Display) menu.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/osd/osddesc.htm 第 3 頁 / 共 3 [98-06-23 09:40]  
 
Customer Care  
arranty  
Customer Care & Warranty  
PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR  
WARRANTY COVERAGE  
LATIN AMERICA: Argentina Brasil  
NORTH AMERICA: Canada USA  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arranty.htm [98-06-23 09:40]  
 
Your Philips F1rst Choice arranty  
Your Philips F1rst Choice Warranty  
Thank you for purchasing this Philips monitor.  
All Philips monitors are designed and manufactured to high standards and deliver  
high-quality performance, ease of use and ease of installation. Should you  
encounter any difficulties while installing or using this product, please contact the  
Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty. This  
three-year service warranty entitles you to a swap model on-site if your monitor  
turns out to be faulty or defective. Philips aims at a swap within 48 hours of your  
call being received.  
What is covered?  
The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark,  
France, Germany, Greece, Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the  
Netherlands, Norway, Poland, Portugal, Sweden, Switzerland, Spain and the United Kingdom and  
only for monitors originally designed, manufactured, approved and/or authorized for usage within  
these countries.  
Warranty coverage begins as from the day you buy your monitor. For three years thereafter, your  
monitor will be swapped by at least an equivalent monitor in case of defects provided for under the  
warranty coverage.  
The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap  
monitor the warranty period remains equal to that of your original monitor, being 36 months as from  
the purchase date of your original monitor.  
What is excluded?  
The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended  
use, in accordance with its operating instructions and upon presentation of the original invoice or  
cash receipt, indicating the date of purchase, dealer's name and model and production number of  
the product.  
The Philips F1rst Choice Warranty may not apply if:  
The documents have been altered in any way or made illegible;  
The model or production number on the product has been altered, deleted, removed or made  
illegible;  
Repairs or product modifications and alterations have been executed by unauthorized service  
organizations or persons;  
Damage is caused by accidents including but not limited to lightning, water or fire, misuse or  
neglect;  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_1st.htm 第 1 頁 / 共 3 [98-06-23 09:41]  
 
Your Philips F1rst Choice arranty  
Reception problems caused by signal conditions or cable or antenna systems outside the  
unit;  
Defects caused by abuse or misuse of the monitor;  
Product requires modification or adaptation to enable it to comply with local or national  
technical standards, which apply in countries for which the product was not originally  
designed, manufactured, approved and/or authorized. Therefore always check whether a  
product can be used in a specific country.  
Note that products that are not originally designed, manufactured, approved and/or  
authorized for usage within the Philips F1rst Choice countries, do not apply to the Philips  
F1rst Choice Warranty. In these cases the Philips global warranty terms are valid.  
Just a click away  
In case of any problems, we advise you to read the operating instructions carefully or go to the www.  
philips.com/support website for additional support.  
Just a phone call away  
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions  
carefully or go to the www.philips.com/support website for additional support before contacting the  
Philips helpdesk.  
To solve your problem quickly, please prepare the following details before contacting the Philips  
helpdesk:  
Philips type number  
Philips serial number  
Purchase date (copy of purchase may be required)  
PC environment Processor:  
❍  
❍  
❍  
CUP and Graphic card name and driver version  
Operating system  
Application being used  
Other cards installed  
Having the following information available will also help speed up the process:  
Your proof of purchase indicating: date of purchase, dealer name, model and product serial  
number.  
The full address to which the faulty monitor has to be collected and the swap model should  
be delivered.  
Philips' customer help desks are located worldwide. Click here to access the F1rst Choice Contact  
Or you can reach us via:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_1st.htm 第 2 頁 / 共 3 [98-06-23 09:41]  
Your Philips F1rst Choice arranty  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_1st.htm 第 3 頁 / 共 3 [98-06-23 09:41]  
F1rst Choice Contact Information  
F1rst Choice Contact Information  
Country  
Code  
+43  
+32  
+45  
+358  
+33  
+49  
+30  
+353  
+39  
+352  
+31  
+47  
+48  
+351  
+34  
+46  
+41  
+44  
Telephone number  
0810 000206  
078 250851  
Tariff  
Austria  
0.07  
Belgium  
Denmark  
Finland  
0.06  
3525 8761  
Local call tariff  
Local call tariff  
0.09  
09 2290 1908  
082161 1658  
01803 386 853  
00800 3122 1223  
01 601 1161  
840 320 041  
26 84 30 00  
France  
Germany  
Greece  
0.09  
Free of charge  
Local call tariff  
0.08  
Ireland  
Italy  
Luxembourg  
The Netherlands  
Norway  
Local call tariff  
0.10  
0900 0400 063  
2270 8250  
Local call tariff  
Local call tariff  
Local call tariff  
0.10  
Poland  
0223491505  
2 1359 1440  
902 888 785  
08 632 0016  
02 2310 2116  
0207 949 0069  
Portugal  
Spain  
Sweden  
Switzerland  
United Kingdom  
Local call tariff  
Local call tariff  
Local call tariff  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arfirst.htm [98-06-23 09:42]  
 
Your Guarantee in Central and Eastern Europe  
Your Guarantee in Central and Eastern Europe  
Dear Customer,  
Thank you for purchasing this Philips product, which has been designed and manufactured to the  
highest quality standards. If, unfortunately, something should go wrong with this product Philips  
guarantees free of charge labor and replacement parts during a period of 36 months from date of  
purchase.  
What is covered?  
This Philips Guarantee in Central and Eastern Europe applies within Czech Republic, Hungary,  
Slovakia, Slovenia, Russia and Turkey and only for monitors originally designed, manufactured,  
approved and/or authorized for usage within these countries.  
Warranty coverage begins as from the day you buy your monitor. For 3 years thereafter, your  
monitor will be serviced in case of defects provided for under the warranty coverage.  
What is excluded?  
The Philips guarantee applies provided the product is handled properly for its intended use, in  
accordance with its operating instructions and upon presentation of the original invoice or cash  
receipt, indicating the date of purchase, dealer's name and model and production number of the  
product.  
The Philips guarantee may not apply if:  
the documents have been altered in any way or made illegible;  
the model or production number on the product has been altered, deleted, removed or made  
illegible;  
repairs or product modifications and alterations have been executed by unauthorized service  
organizations or persons;  
damage is caused by accidents including but not limited to lightning, water or fire, misuse or  
neglect.  
Reception problems caused by signal conditions or cable or antenna systems outside the  
unit;  
Defects caused by abuse or misuse of the monitor;  
Product requires modification or adaptation to enable it to comply with local or national  
technical standards, which apply in countries for which the product was not originally  
designed, manufactured, approved and/or authorized. Therefore always check whether a  
product can be used in a specific country.  
Please note that the product is not defective under this guarantee in the case where modifications  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_ee.htm 第 1 頁 / 共 2 [98-06-23 09:42]  
 
Your Guarantee in Central and Eastern Europe  
become necessary in order for the product to comply with local or national technical standards  
which apply in countries for which the product was not originally designed and/or manufactured.  
Therefore always check whether a product can be used in a specific country.  
Just a click away  
In case of any problems, we advise you to read the operating instructions carefully or go to the www.  
philips.com/support website for additional support.  
Just a phone call away  
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions  
carefully before contacting our dealers or Information Centers  
In case your Philips product is not working correctly or is defective, please contact your Philips  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_ee.htm 第 2 頁 / 共 2 [98-06-23 09:42]  
Consumer Information Centers  
Consumer Information Centers  
Eastern Europe  
BELARUS  
Technic al Center of JV IBA  
M. Bogdanovich str. 155  
BY - 220040 Minsk  
Tel: +375 17 217 33 86  
BELARUS  
Service.BY  
Petrus Brovky st. 19 101-B  
220072, Minsk  
Belarus  
BULGARIA  
LAN Service  
140, Mimi Balkanska Str.  
Office center Translog  
1540 Sofia, Bulgaria  
Tel: +359 2 960 2360  
www.lan-service.bg  
CZECH REPUBLIC  
General Consumer Information Center  
800 142100  
Xpectrum  
Lu.ná 591/4  
CZ - 160 00 Praha 6 Tel: 800 100 697 or 220 121 435  
Email:info@xpectrum.cz  
www.xpectrum.cz  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 1 頁 / 共 9 [98-06-23 09:42]  
       
Consumer Information Centers  
CROATIA  
Renoprom d.o.o.  
Ljubljanska 4,  
Sv. Nedjelja,10431  
Croatia  
Tel: +385 1 333 0974  
ESTONIA  
FUJITSU SERVICES OU  
Akadeemia tee 21G  
EE-12618 Tallinn  
Tel: +372 6519900  
www.ee.invia.fujitsu.com  
HUNGARY  
Serware Szerviz  
Vizimolnár u. 2-4  
HU - 1031 Budapest  
Tel: +36 1 2426331  
Email: inbox@serware.hu  
www.serware.hu  
HUNGARY  
Profi Service Center Ltd.  
123 Kulso-Vaci Street,  
H-1044 Budapest ( Europe Center )  
Hungary  
Tel: +36 1 814 8080  
m.andras@psc.hu  
LATVIA  
ServiceNet LV  
Jelgavas iela 36  
LV - 1055 Riga,  
Tel: +371 7460399  
Email: serviss@servicenet.lv  
LITHUANIA  
ServiceNet LT  
Gaiziunu G. 3  
LT - 3009 KAUNAS  
Tel: +370 7400088  
Email: servisas@servicenet.lt  
www.servicenet.lt  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 2 頁 / 共 9 [98-06-23 09:42]  
         
Consumer Information Centers  
ROMANIA  
Blue Ridge Int'l Computers SRL  
115, Mihai Eminescu St., Sector 2  
RO - 020074 Bucharest  
Tel: +40 21 2101969  
SERBIA & MONTENEGRO  
Kim Tec d.o.o.  
Viline vode bb, Slobodna zona  
Beograd L12/3  
11000 Belgrade  
Serbia  
Tel. +381 11 20 70 684  
SLOVAKIA  
General Consumer Information Center  
0800004551  
Datalan Servisne Stredisko  
Puchovska 8  
SK - 831 06 Bratislava  
Tel: +421 2 49207155  
Email: servis@datalan.sk  
SLOVENIA  
PC HAND  
Brezovce 10  
SI - 1236 Trzin  
Tel: +386 1 530 08 24  
Email: servis@pchand.si  
RUSSIA  
CPS  
18, Shelepihinskaya nab.  
123290 Moscow  
Russia  
Tel. +7(495)797 3434  
Profservice:  
14A -3, 2Karacharovskaya str,  
109202, Moscow ,  
Russia  
Tel. +7(095)170-5401  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 3 頁 / 共 9 [98-06-23 09:42]  
         
Consumer Information Centers  
TURKEY  
Türk Philips Ticaret A.S.  
Yukari Dudullu Org.San.Bolgesi  
2.Cadde No:22  
34776-Umraniye/Istanbul  
Tel: (0800)-261 33 02  
UKRAINE  
Comel  
Shevchenko street 32  
UA - 49030 Dnepropetrovsk  
Tel: +380 562320045  
www.csp-comel.com  
LLC Topaz Company  
Topaz-Service Company,  
Mishina str. 3,  
Kiev  
Ukraine-03151  
Tel: +38 044 245 73 31  
Latin America  
ARGENTINA  
Azopardo 1480.  
(C1107ADZ) Cdad. de Buenos Aires  
Tel: 0800 3330 856  
Email: CIC.monitores@Philips.com  
BRASIL  
Alameda Raja Gabaglia, 188 - 10°Andar - V.  
Olímpia - S. Paulo/SP - CEP 04551-090 -  
Brasil  
Tel: 0800-7254101  
Email: CIC.monitores@Philips.com  
Pacific  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 4 頁 / 共 9 [98-06-23 09:42]  
       
Consumer Information Centers  
AUSTRALIA  
Company: AGOS NETWORK PTY LTD  
Address: 4/5 Dursley Road, Yenorra, NSW 2161, Australia  
Tel: 1300 360 386  
Fax: +61-2-80808147  
Email: philips@agos.com.au  
Service hours: Mon.~Fri. 8:00am-7:30pm  
NEW ZEALAND  
Company: Visual Group Ltd.  
Address: 28 Walls Rd Penrose Auckland  
Phone: 0800 657447  
Fax: 09 5809607  
E-mail: vai.ravindran@visualgroup.co.nz  
Service Hours: Mon.~Fri. 8:30am~5:30pm  
Asia  
HONG KONG/Macau  
Company Name: PHK Service Limited  
Address: Flat A, 10/F., Pak Sun Building, 103 - 107 Wo Yi Hop Road, Kwai Chung, New Territories, Hong  
Kong  
Tel.: (852) 2610-6908 / (852) 2610-6929 for Hong Kong and (853) 2856-2277 for Macau  
Fax: (852) 2485 3574 for Hong Kong and (853) 2856 1498 for Macau  
E-mail: enquiry@phkservice.com.hk  
Service Hours: Mon.~Sat. 09:00am~06:00pm  
India  
Company: REDINGTON INDIA LTD  
Address: SPL Guindy House, 95 Mount Road, Chennai 600032, India  
Tel: +9144-42243352/353  
E-mail: aftersales@in.aocmonitor.com  
Service hours: Mon.~Fri. 9:00AM~5:30PM; Sat. 9:00AM~1:00PM  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 5 頁 / 共 9 [98-06-23 09:42]  
     
Consumer Information Centers  
Indonesia  
Company Name: PT. Gadingsari elektronika Prima  
Address: Kompleks Pinang 8, Jl. Ciputat raya No. 8F, Pondok Pinang. Jakarta  
Tel: 021-750909053, 021-750909056  
Fax: 021-7510982  
E-mail: gepta@cbn.net.id  
Service hours: Mon.~Fri. 8:30am~4:30pm; Sat. 8:30am~2:00pm  
Additional service points:  
1. Philips Building Jl. Buncit Raya Kav 99. Jakarta Selatan.  
Phone: 021-7940040, ext 1722/1724, 98249295, 70980942  
2. Jl. Tanah Abang 1 no 12S. Jakarta Pusat.  
Phone: 021-3455150, 34835453  
3. Rukan City Home no H31, Gading Square. Jl. Bulevar Barat. Kelapa Gading. Jakarta Utara. Phone: 021-  
45870601, 98131424  
South Korea  
Company: PCS One Korea Ltd.  
Address: 112-2, Banpo-dong, Seocho-ku, Seoul, 137-040, Korea  
Call Center Tel: 080-600-6600  
Tel: 82 2 591 1528  
Fax: 82 2 595 9688  
E-mail: cic_korea@philips.com  
Service hours: Mon.~Fri. 9:00AM~ 6:00PM; Sat. 9:00AM~1:00PM  
Malaysia  
Company: After Market Solutions (CE) Sdn Bhd  
Address: Lot 6. Jalan 225/51A, 46100 Petaling Jaya, Selangor DE, Malaysia.  
Phone: 603 7953 3370  
Philips Info Line: 1-800-880-180  
Fax: 603 7953 3338  
E-mail: pceinfo.my@philips.com  
Service Hours: Mon.~Fri. 8:15am~5:15pm; Sat. 9:00am~1:00pm  
Pakistan  
Philips Consumer Service  
Address: Mubarak manzil, 39, Garden Road, Saddar, Karachi-74400  
Tel: (9221) 2737411-16  
Fax: (9221) 2721167  
E-mail: care@philips.com  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 6 頁 / 共 9 [98-06-23 09:42]  
       
Consumer Information Centers  
Singapore  
Company: Philips Electronics Singapore Pte Ltd (Philips Consumer Care Center)  
Address: 620A Lorong 1 Toa Payoh, TP4 Building Level 1, Singapore 319762  
Tel: (65) 6882 3999  
Fax: (65) 62508037  
E-mail: consumer.care.sg@philips.com  
Service hours: Mon.~Fri. 9:00am~6:00pm; Sat. 9:00am~1:00pm  
Taiwan  
Company: FETEC.CO  
Address: 3F, No.6, Lane 205, Sec. 1, Chang Hsing Rd, Lu Chu Hs, Taoyuan, Taiwan R.O.C 33800  
Consumer Care: 0800-231-099  
Tel: (03)2120336  
Fax: (03)3129184  
E-mail: knlin08@xuite.net  
Service hours: Mon.~Fri. 8:30am~7:00pm  
Thailand  
Company: Axis Computer System Co., Ltd.  
Address: 1421 Soi Lardprao 94, Srivara Town In Town Soi 3 Road, Wangthonglang, Bangkok 10310  
Thailand  
Tel: (662) 934-5498  
Fax: (662) 934-5499  
E-mail: axis5@axiscomputer.co.th  
Service Hours: Mon.~Fri. 08:30am~05:30pm  
Vietnam  
Company: Digiworld Corp  
Address: 211-213 Vo Van Tan St, Ward 5, Dist.3 , Ho Chi Minh city, Vietnam  
Tel: 848-38266065  
Fax: 848-38267307  
E-mail: Digicare@dgw.com.vn  
Service hours: 8:00 to 12:00 AM and 13:30 to 17:30 PM (from Monday to Friday)  
Philippines  
Glee Electronics Inc  
Contact nos. (632) 636-3636 / 7064028 to 29  
Fax no. (632) 7064026  
Receiving Centers  
NEO CARE - Megamall  
4th Level Cyberzone, Building B,  
SM Megamall, Mandaluyong City  
NEO CARE - SM North EDSA  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 7 頁 / 共 9 [98-06-23 09:42]  
     
Consumer Information Centers  
4th Level Cyberzone, Annex Bldg.  
SM City North EDSA, Quezon City  
441-1610  
MDR Microware Sales Inc.  
Cebu Branch  
N. Escario corner Clavano St., Cebu City Phils.  
# 255-4415/ 255-3242/253-9361/4124864 to 67  
Sun # 0922-8210045 to 46  
Davao Office:  
C. Arellano St., Davao City 8000  
082- 225-3021/225-3022  
Sun# 0922-8210015  
CDO Office:  
1445 Corrales Ext.,CDO City  
088-856-8540/856-8541  
Sun # 0922-8210080  
Iloilo Office:  
C. Lim Comp., Gomez St., Iloilo City  
# 033 338-4159/ 033 508-3741  
Sun # 0922-8808850  
Africa  
SOUTH AFRICA  
Company name: Sylvara Technologies Pty Ltd  
Address: Ho Address Palm Springs Centre Christoffel Road Van Riebeeck Park Kempton Park, South Africa  
Tel: +27878084456  
Fax: +2711 391 1060  
E-mail: customercare@philipssupport.co.za  
Service hours: Mon.~ Fri. 08:00am~05:00pm  
Middle East  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 8 頁 / 共 9 [98-06-23 09:42]  
 
Consumer Information Centers  
Middle East + North Africa  
Company: AL SHAHD COMPUTER L.L.C  
Address: P.O.BOX: 29024, DUBAI, UNITED ARAB EMIRATES  
TEL: 00971 4 2276525  
FAX: 00971 4 2276242  
E-mail: shahd52@eim.ae  
Service hours: Sat.~Thur. 9:00am~1:00pm & 4:00pm- 8:00pm  
Israel  
Company: Eastronics LTD  
Address: 13 Rozanis St. P.O.B. 39300, Tel Aviv 61392 Israel  
Tel: 1-800-567000 call free in Israel; (972-50-8353722 after service hours until 20:00)  
Fax: 972-3-6458759  
E-mail: eastronics@eastronics.co.il  
Service hours: Sun.~Thurs. 08:00 - 18:00  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 9 頁 / 共 9 [98-06-23 09:42]  
   
International Guarantee  
Your International Guarantee  
Dear Customer,  
Thank you for purchasing this Philips product which has been designed and manufactured to the  
highest quality standards.  
If, unfortunately, something should go wrong with this product Philips guarantees free of charge  
labor and replacement parts irrespective of the country where it is repaired during a period of 12  
months from date of purchase. This international Philips guarantee complements the existing  
national guarantee obligations to you of dealers and Philips in the country of purchase and does not  
affect your statutory rights as a customer.  
The Philips guarantee applies provided the product is handled properly for its intended use, in  
accordance with its operating instructions and upon presentation of the original invoice or cash  
receipt, indicating the date of purchase, dealer's name and model and production number of the  
product.  
The Philips guarantee may not apply if:  
the documents have been altered in any way or made illegible;  
the model or production number on the product has been altered, deleted, removed or made  
illegible;  
repairs or product modifications and alterations have been executed by unauthorized service  
organizations or persons;  
damage is caused by accidents including but not limited to lightning, water or fire, misuse or  
neglect.  
Please note that the product is not defective under this guarantee in the case where modifications  
become necessary in order for the product to comply with local or national technical standards  
which apply in countries for which the product was not originally designed and/or manufactured.  
Therefore always check whether a product can be used in a specific country.  
In case your Philips product is not working correctly or is defective, please contact your Philips  
dealer. In the event you require service whilst in another country a dealer address can be given to  
you by the Philips Consumer Help Desk in that country, the telephone and fax number of which can  
be found in the relevant part of this booklet.  
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions  
carefully before contacting your dealer. If you have questions which your dealer cannot answer or  
any related question please contact the Philips Consumer Information Centers or via:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_intl.htm 第 1 頁 / 共 2 [98-06-23 09:42]  
 
International Guarantee  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_intl.htm 第 2 頁 / 共 2 [98-06-23 09:42]  
United States Guarantee  
Your Philips F1rst Choice Warranty(USA)  
Thank you for purchasing this Philips monitor.  
All Philips monitors are designed and manufactured to high standards and  
deliver high-quality performance, ease of use and ease of installation. Should  
you encounter any difficulties while installing or using this product, please  
contact Philips directly to benefit from your Philips F1rst Choice Warranty. This  
three-year service warranty entitles you to a swap model on-site within 48  
hours of your call being received within the first year of purchase. If you have  
any problems with your monitor within the second or third year of purchase, we  
will repair it after it has been sent to the service provider at your expense and  
returned to you within five working days, free of charge.  
LIMITED WARRANTY (Computer Monitor)  
Click here to access the Warranty Registration Card.  
Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange*  
*Product will be exchanged with a new or renewed to original specifications unit within two  
business days for the first year. This product must be shipped in at your expense for service during  
years two and three.  
WHO IS COVERED?  
You must have proof of purchase to receive warranty service. A sales receipt or other document  
showing that you purchased the product is considered proof of purchase. Attach it to this owner's  
manual and keep both nearby.  
WHAT IS COVERED?  
Warranty coverage begins the day you buy your product. For three years thereafter, all parts will be  
repaired or replaced, and labor is free. After three years from the day of purchase, you pay for the  
replacement or repair of all parts, and for all labor charges.  
All parts, including repaired and replaced parts, are covered only for the original warranty period.  
When the warranty on the original product expires, the warranty on all replaced and repaired  
products and parts also expires.  
WHAT IS EXCLUDED?  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_usa.htm 第 1 頁 / 共 4 [98-06-23 09:43]  
 
United States Guarantee  
Your warranty does not cover:  
labor charges for installation or setup of the product, adjustment of customer controls on the  
product, and installation or repair of antenna systems outside of the product.  
product repair and/or part replacement because of misuse, accident, unauthorized repair or  
other cause not within the control of Philips Consumer Electronics.  
reception problems caused by signal conditions or cable or antenna systems outside the  
unit.  
a product that requires modification or adaptation to enable it to operate in any country other  
than the country for which it was designed, manufactured, approved and/or authorized, or  
repair of products damaged by these modifications.  
incidental or consequential damages resulting from the product. (Some states do not allow  
the exclusion of incidental or consequential damages, so the above exclusion may not apply  
to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not  
copyrighted.)  
the model or production number on the product has been altered, deleted, removed or made  
illegible.  
Where IS SERVICE AVAILABLE?  
Warranty service is available in all countries where the product is officially distributed by Philips  
Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the  
product, the local Philips service organization will attempt to provide service (although there may be  
a delay if the appropriate spare parts and technical manual(s) are not readily available).  
Where CAN I GET MORE INFORMATION?  
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.  
customers only) or (919) 573-7855.  
Before Requesting Service...  
Please check your owner's manual before requesting service. Adjustments of the controls  
discussed there may save you a service call.  
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...  
Contact the Philips Customer Care Center phone number listed below for product assistance and  
procedures for servicing:  
Philips Customer Care Center  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_usa.htm 第 2 頁 / 共 4 [98-06-23 09:43]  
United States Guarantee  
(877) 835-1838 or (919) 573-7855  
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties  
of merchantability and fitness for a particular purpose, are limited in duration to the duration of this  
express warranty. But, because some states do not allow limitations on how long an implied  
warranty may last, this limitation may not apply to you.)  
TO GET WARRANTY SERVICE IN CANADA...  
Please contact Philips at:  
(800) 479-6696  
Three years free parts and three years free labor will be provided at Philips Canada depot or any  
one of its authorized service centers.  
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed  
or implied, including any implied warranties of merchantability or fitness for a particular purpose.  
Philips is not liable under any circumstances for any direct, indirect, special, incidental or  
consequential damages, howsoever incurred, even if notified of the possibility of such damages.)  
REMEMBER... Please record the model and serial numbers found on the product below.  
MODEL # ________________________________________________  
SERIAL # ________________________________________________  
This warranty gives you specific legal rights. You may have other rights which vary from state/  
province to state/province.  
Before contacting Philips, please prepare the following details so we can solve your problem  
quickly.  
Philips type number  
Philips serial number  
Purchase date (copy of purchase may be required)  
PC environment Processor:  
❍  
❍  
❍  
CUP and Graphic card name and driver version  
Operating system  
Application being used  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_usa.htm 第 3 頁 / 共 4 [98-06-23 09:43]  
United States Guarantee  
Other cards installed  
Having the following information available will also help speed up the process:  
Your proof of purchase indicating: date of purchase, dealer name, model and product serial  
number.  
The full address to which the swap model should be delivered.  
Just a phone call away  
Philipscustomer help desks are located worldwide. Within the U.S. you can contact Philips  
customer care Monday-Friday from 8:00 AM-9:00 PM Eastern Time (ET) and on Saturdays from  
10:00 AM-5:00 PM ET hrs by using one of the contact phone numbers.  
For more information on this and more great Philips products visit our website at:  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_usa.htm 第 4 頁 / 共 4 [98-06-23 09:43]  
Glossary  
Glossary  
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z  
A
Active matrix  
This is a kind of liquid crystal display structure in which switching transistors are attached to each  
pixel to control the on/off voltage. It produces a brighter and sharper display with a broader viewing  
angle than a passive matrix display. Also refer to TFT (thin film transistor).  
Amorphous silicon (a-Si)  
A semiconductor material that is used to make the thin film transistors (TFTs) layer of an active  
matrix LCD.  
Aspect ratio  
The width-to-height ratio of the active area of a display. In general, most monitors have an aspect  
ratio of 4:3. Wide monitors or TVs have an aspect ratio of 16:9 or 16:10.  
Backlight  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 1 頁 / 共 10 [98-06-23 09:43]  
       
Glossary  
The light source for a transmissive LCD. There are two techniques used in nowaday LCD designs.  
Most TFT LCD panels use CCFLs (cold cathode fluorescent light) and a diffuser panel directly  
behind the liquid crystal layer. New technology using Light Emitting Diodes (LED) are still under  
development.  
Brightness  
The dimension of color that is referred to an achromatic scale, ranging from black to white, also  
called lightness or luminous reflectance. Because of confusion with saturation, the use of this term  
should be discouraged.  
C
CCFL(cold cathode fluorescent light)  
These are the fluorescent light tubes providing the light for the LCD module. These tubes are  
generally very thin, approximately 2 mm in diameter.  
Chromaticity  
That part of color specification, which does not involve illuminance. Chromaticity is two-dimensional  
and specified by pairs of numbers such as dominant wavelength and purity.  
CIE (Commission International de I'Eclairage)  
The International Commission on Illumination, the primary international organization concerned with  
color and color measurement.  
Color temperature  
A measurement of the color of light radiated by an object while it is being heated. This  
measurement is express in terms of absolute scale, (degrees Kelvin). Lower Kelvin temperatures  
such as 2400° K are red; higher temperatures such as 9300° K are blue. Neutral temperature is  
white, at 6504° K. Philips monitors generally offers 9300° K, 6500° K, and user define.  
Contrast  
The luminance variation between light and dark areas in an image.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 2 頁 / 共 10 [98-06-23 09:43]  
 
Glossary  
Contrast ratio  
The ratio of luminance between the brightest white pattern and the darkest black pattern.  
D
D-SUB  
A VGA Analog input connector. Your monitor comes with a D-Sub cable.  
Digital Visual Interface (DVI) (available for selective models)  
The Digital Visual Interface (DVI) specification provides a high-speed digital connection for visual  
data types that is display technology independent. The interface is primarily focused at providing a  
connection between a computer and its display device. The DVI specification meets the needs of all  
segments of the PC industry (workstation, desktop, laptop, etc.) and will enable these different  
segments to unite around one monitor interface specification.  
The DVI interface enables:  
1. Reduce signal loss and video noise in signal due to less signal conversion.  
2. Independent from display technology, and can be used on LCD, Plasma, LCOS, etc.  
3. Plug and play through hot plug detection, EDID and DDC2B.  
4. Digital and Analog support in a single connector (DVI-I only).  
E
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 3 頁 / 共 10 [98-06-23 09:43]  
   
Glossary  
Energy Star Computers Program  
An energy conservation program launched by the US Environmental Protection Agency (EPA),  
promotes the manufacture and marketing of energy-efficient office automation equipment.  
Companies joining this program, must be willing to commit themselves to manufacture one or more  
products capable of going into a low -power state (< 30 W) either after a period of inactivity, or after  
a predetermined time selected by the user.  
Gamma  
Screen luminance as a function of video voltage approximately follows a mathematical power  
function of the input video signal, the exponent of which is called gamma.  
Grayscale  
An achromatic scale ranging from black through a series of successively lighter grays to white.  
Such a series may be made up of steps, which appear to be equally distant from one another. If the  
Analog/ Digital converter is 8 bit, then the monitor can display at most 28 = 256 levels. For a color  
monitor, R.G.B. each color hads 256 levels. Thus, total color can display is 256x256x256= 16.7  
million.  
Hue  
The main attribute of a color that distinguishes it from other colors. For example, a color may have a  
green, yellow, or purple hue. Color defined as having hue are know as chromatic colors. White,  
black, and grays possess no hue.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 4 頁 / 共 10 [98-06-23 09:43]  
   
Glossary  
IPS (In Plane Switching)  
A technique of improving the viewing angle of an LCD where the liquid crystal molecules are  
switched in the plane of the LCD layer rather than vertical to it.  
L
LCD (liquid crystal display)  
A display composed of liquid crystal suspended between two transparent sheets. The display is  
composed thousands of pixels which can be turned on or off with electrical stimulation. Thus,  
colorful images/texts can be generated.  
Liquid crystal  
The compound found in liquid crystal displays. Liquid crystal reacts predictably when electrically  
stimulated. This makes it the ideal compound to turn LCD pixels "on" or "off." Liquid crystal is  
sometimes abbreviated as LC.  
Luminance  
A measure of the brightness or luminous intensity of light, usually expressed in units of Candelas  
per square meter (cd/m2) or foot Lamberts. 1 fL=3.426 cd/m2.  
Nit  
A unit of luminance equal to 1 cd/m2 or 0.292 ftL.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 5 頁 / 共 10 [98-06-23 09:43]  
     
Glossary  
Pixel  
PICture Element; the smallest element on a computerized CRT or LCD image, and hence a display.  
Polarizer  
A light filter which only allows light waves of a certain rotation through. Polarized material with  
perpendicular filtering is used in LCDs to enclose the liquid crystal. The liquid crystal is then used  
as the medium which twists the light waves 90° in order to allow the light to pass through or not.  
Refresh rate  
The number of times per second the screen is refreshed or redrawn. This number is usually stated  
in Hz (Hertz) or cycles per second. A rate of 60 Hz is equal to 60 tomes per second.  
SmartContrast  
Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD  
monitor's contrast ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting  
for clearer, crisper and brighter images or dimming backlighting for clear display of images on dark  
backgrounds. For monitors with SmartContrast, contrast ratio achieves 3000:1, the highest  
available today in a desktop LCD monitor.  
SmartControl II  
SmartControl II is monitor-based software with an easy-to-use on-screen graphic interface that  
guides you through fine-tuning resolution, color calibration and other display settings including  
brightness, contrast, clock & phase, position, RGB, white point and - on models with onboard  
speakers - volume adjustments.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 6 頁 / 共 10 [98-06-23 09:43]  
   
Glossary  
SmartImage  
SmartImage provides presets that optimize display for different types of content, dynamically  
adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text  
applications, displaying images or watching a video, Philips SmartImage delivers great optimized  
LCD display performance.  
SmartResponse  
SmartResponse is exclusive Philips technology that adjusts response time to application  
requirements, delivering faster response times for gaming and videos or better color saturation for  
viewing photos and static images.  
SmartManage Lite  
SmartManage Lite is a system for monitoring, managing and checking status of display devices  
designed to meet the specific needs of growing small and medium-size businesses that minimizes  
costs and maximizes IT staff efficiency by remotely controlling key display settings, providing status  
reports, compiling usage data, overseeing energy consumption and deterring thefts.  
sRGB  
sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital  
cameras, monitors, printers, scanners, etc.)  
Using a standard unified color space, sRGB will help represent pictures taken by an sRGB  
compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are  
calibrated and you can rely on the correctness of the colors shown on your screen.  
Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a  
predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in  
the monitor's OSD.  
To do so, open the OSD by pressing the OK button on the front of your monitor. Move the down  
button to go to Color and press OK again. Use the right button to go to sRGB. Then move the down  
button and press OK again to exit the OSD.  
After this, please do not change the brightness or contrast setting of your monitor. If you change  
either of these, the monitor will exit the sRGB mode and go to a color temperature setting of 6500K.  
Other:  
USB plug: An upstream and a downstream USB plug is provide for user's convenience.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 7 頁 / 共 10 [98-06-23 09:43]  
Glossary  
TFT(thin film transistor)  
Usually made from amorphous silicon (a-Si) and used as a switch to a charge storage device  
located below each sub-pixel on an active matrix LCD.  
TrueVision  
TrueVision is industry-leading, proprietary Philips testing and algorithm technology for monitor  
adjustment and fine tuning, an extensive process that ensures ultimate display performance in  
compliance with a standard four-times more stringent than Microsoft's Vista requirements from each  
and every monitor that leaves the factory - not just a few review samples. Only Philips goes to these  
lengths to deliver this exacting level of color accuracy and display quality in every new monitor.  
U
USB or Universal Serial Bus  
A smart plug for PC peripherals. USB automatically determines resources (like driver software and  
bus bandwidth) required by peripherals. USB makes necessary resources available without user  
intervention.  
USB eliminates "case anxiety" -- the fear of removing the computer case to install add-on  
peripherals. USB also eliminates adjustment of complicated IRQ settings when installing  
new peripherals.  
USB does away with "port gridlock." Without USB, PCs are normally limited to one printer,  
two Com port devices (usually a mouse and modem), one Enhanced Parallel Port add-on  
(scanner or video camera, for example) and a joystick. More and more peripherals for  
multimedia computers arrive on the market every day. With USB, up to 127 devices can run  
simultaneously on a computer.  
USB permits "hot plug-in." There's no need to shut down, plug in, reboot and run set-up to  
install peripherals. And no need to go through the reverse process to unplug a device.  
In short, USB transforms today's "Plug-and-Pray" into true Plug-and-Play!  
Hub  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 8 頁 / 共 10 [98-06-23 09:43]  
   
Glossary  
A Universal Serial Bus device that provides additional connections to the Universal Serial Bus.  
Hubs are a key element in the plug-and-play architecture of USB. The Figure shows a typical hub.  
Hubs serve to simplify USB connectivity from the user's perspective providing low cost and  
complexity.  
Hubs are wiring concentrators and enable the multiple attachment characteristics of USB.  
Attachment points are referred to as ports. Each hub converts a single attachment point into  
multiple attachment points. The architecture supports concatenation of multiple hubs.  
The upstream port of a hub connects the hub towards the host. Each of the other downstream ports  
of a hub allows connection to another hub or function. Hubs can detect, attach and detach at each  
downstream port and enable the distribution of power to downstream devices. Each downstream  
port can be individually enabled and configured at either full or low speed. The hub isolates low  
speed ports from full speed signaling.  
A hub consists of two portions: the Hub Controller and Hub Repeater. The repeater is a protocol-  
controlled switch between the upstream port and downstream ports. It also has hardware support  
for reset and suspend/resume signaling. The controller provides the interface registers to allow  
communication to/from the host. Hub specific status and control commands permit the host to  
configure a hub and to monitor and control its ports.  
Device  
A logical or physical entity that performs a function. The actual entity described depends on the  
context of the reference. At the lowest level, device may refer to a single hardware component, as  
in a memory device. At a higher level, it may refer to a collection of hardware components that  
perform a particular function, such as a Universal Serial Bus interface device. At an even higher  
level, device may refer to the function performed by an entity attached to the Universal Serial Bus;  
for example, a data/FAX modem device. Devices may be physical, electrical, addressable, and  
logical.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 9 頁 / 共 10 [98-06-23 09:43]  
Glossary  
Downstream  
The direction of data flow from the host or away from the host. A downstream port is the port on a  
hub electrically farthest from the host that generates downstream data traffic from the hub.  
Downstream ports receive upstream data traffic.  
Upstream  
The direction of data flow towards the host. An upstream port is the port on a device electrically  
closest to the host that generates upstream data traffic from the hub. Upstream ports receive  
downstream data traffic.  
V
Vertical refresh rate  
Expressed in Hz, it is the number of frames (complete pictures) written to the screen every second.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5...0V401.001/CD-Contents/lcd/manual/ENGLISH/220C1/glossary/glossary.htm 第 10 頁 / 共 10 [98-06-23 09:43]  
 
Do nload and Print  
Download and Print  
Installing Your LCD monitor driver  
System requirements:  
PC running Windows 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP,  
Windows® Vista or later  
Find your driver ".inf/.icm/.cat" at : /PC/drivers/  
Read the "Readme.txt" file before installing.  
This page provides an option to read the manual in .pdf format. PDF files can be downloaded into  
your hard disk, then viewed and printed with Acrobat Reader or through your browser.  
If you do not have Adobe® Acrobat Reader installed, click on the link to install the application.  
Download instructions:  
To download the file:  
1. Click-and-hold your mouse over the icon below. (Windows® 95/98/2000/Me/XP/Vista users right-  
click)  
Download  
2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to  
Disk'.  
3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or  
'source', choose 'source').  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/do nload/do nload.htm 第 1 頁 / 共 2 [98-06-23 09:43]  
       
Do nload and Print  
Printing instructions:  
To print the manual:  
With the manual file open, follow your printer's instructions and print the pages you need.  
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/220C1/220C1-EDFU/5B.0V401.001/CD-Contents/lcd/manual/ENGLISH/do nload/do nload.htm 第 2 頁 / 共 2 [98-06-23 09:43]  

Intel ATOM US15W User Manual
JVC AV 21PB4N User Manual
LG Electronics LG Life Good Computer Monitor W1943T User Manual
MSi MS 7242 User Manual
Panasonic WV LC1900 User Manual
Philips 21PT4439 User Manual
Philips 33CE7539 User Manual
Philips BDH5031V 00 User Manual
Philips BDL4231C User Manual
Philips DVP3550KX User Manual