Mitsubishi Electronics Mitsubishi Digital Electronics Computer Hardware GT15 75QBUSL User Manual

[DESIGN PRECAUTIONS]  
CAUTION  
[DISPOSAL PRECAUTIONS]  
CAUTION  
1. Overview  
This User's Manual describes the GT15 bus connection unit  
(hereafter abbreviated to the bus connection unit).  
There are the following bus connection unit types.  
Refer to the GT15 User's Manual for the applicable GOT.  
z
Do not bunch the control wires or communication cables with  
z
Dispose of this product as industrial waste.  
the main circuit or power wires, or lay them close to each other.  
As a guide, separate the lines by a distance of at least 100 mm  
(3.94 inch) otherwise malfunctions may occur due to noise.  
[TRANSPORTATION PRECAUTIONS]  
CAUTION  
GT15 BUS CONNECTION UNIT  
User's Manual  
Product  
name  
[INSTALLATION PRECAUTIONS]  
DANGER  
Model name  
Description  
z
Make sure to transport the GOT main unit and/or relevant unit(s)  
in the manner they will not be exposed to the impact exceeding  
the impact resistance described in the general specifications of  
the GT15 User's Manual, as they are precision devices.  
Failure to do so may cause the unit to fail.  
GT15-75QBUSL  
GT15-75QBUS2L  
GT15-75ABUSL  
GT15-75ABUS2L  
QCPU (Q Mode) bus connection  
Number of connectors: 1  
GT15- 75QBUSL  
GT15- 75QBUS2L  
GT15- 75ABUSL  
GT15- 75ABUS2L  
z
Before mounting or dismounting this unit to or from the GOT,  
always shut off GOT power externally in all phases.  
Not doing so can cause a unit failure or malfunction.  
QCPU (Q Mode) bus connection  
Number of connectors: 2  
Check if the unit operates correctly after transportation.  
Bus  
connection  
unit  
QnA/ACPU bus connection  
Number of connectors: 1  
CAUTION  
Manuals  
z
z
Use this unit in the environment given in the general  
specifications of the GT15 User's Manual.  
Not doing so can cause an electric shock, fire, malfunction or  
product damage or deterioration.  
The following shows manuals relevant to this product.  
QnA/ACPU bus connection  
Number of connectors: 2  
Detailed Manual  
Use the bus connection unit for making bus connection of the  
GOT.  
Select the used bus connection unit according to the  
connection target and connection position.  
When installing this unit to the GOT, fit it to the connection  
interface of the GOT and tighten the mounting screws in the  
specified torque range.  
Undertightening can cause a drop, failure or malfunction.  
Overtightening can cause a drop, failure or malfunction due to  
screw or unit damage.  
Thank you for purchasing the GOT1000 Series.  
Manual Number  
Manual name  
(Type code)  
Prior to use, please read both this manual and detailed  
manual thoroughly to fully understand the product.  
GT15 User's Manual  
SH-080528ENG  
(1D7M23)  
<Bus connection unit selection example>  
(Option)  
(1) Select the bus connection unit according to the  
connection target.  
GOT1000 Series Connection Manual  
SH-080532ENG  
(1D7M26)  
(Option)  
[WIRING PRECAUTIONS]  
DANGER  
MODEL  
GT15-75BUSL-U  
1D7M04  
QCPU (Q Mode), motion controller Q series  
: GT15-75QBUSL/GT15-75QBUS2L  
ACPU, QnACPU, motion controller A series  
: GT15-75ABUSL/GT15-75ABUS2L  
MODEL  
CODE  
Relevant Manuals  
z
Before connecting the Bus connection cable to this unit, always  
For relevant manuals, refer to the PDF manual stored within the  
drawing software used.  
IB(NA)-0800298-B(0504)MEE  
shut off GOT power and PLC CPU power externally in all  
phases.  
Not doing so can cause a malfunction.  
(2) Select the bus connection unit according  
to the GOT connection position.  
© 2004 MITSUBISHI ELECTRIC CORPORATION  
CAUTION  
Placed midway  
Compliance with the EMC and Low Voltage  
Directives  
When incorporating the Mitsubishi GOT into other machinery or  
equipment and keeping compliance with the EMC and low voltage  
directives, refer to Chapter 4, "EMC Directives and Low Voltage  
Directives" of the manual (GT15 General Description) included with  
the GOT used.  
The CE logo is printed on the rating plate of the GOT, indicating  
compliance with the EMC and low voltage directives.  
By making this product conform to the EMC directive and low  
voltage instruction,it is not necessary to make those steps  
individually.  
: GT15-75QBUS2L/GT15-75ABUS2L  
z
Insert and fit the bus connection cable into the connector of the  
unit to be connected until it "clicks".  
After fitting, check for lift which can cause a malfunction due to a  
connection fault.  
zSAFETY PRECAUTIONSz  
(Always read these precautions before using this equipment.)  
Before using this product, please read this manual and the relevant  
manuals introduced in this manual carefully and pay full attention to  
safety to handle the product correctly.  
The precautions given in this manual are concerned with this prod-  
uct.  
[STARTUP AND MAINTENANCE PRECAUTIONS]  
DANGER  
Placed at end  
: GT15-75QBUSL/GT15-75ABUSL  
GT15-75QBUS2L/GT15-75ABUS2L  
z
Before starting cleaning, always shut off GOT power externally  
in all phases. Not doing so can cause a unit failure or  
malfunction.  
In this manual, the safety precautions are ranked as "DANGER" and  
"CAUTION".  
Refer to the GOT1000 Series Connection Manual for details of  
bus connection.  
Product Components  
The bus connection unit consists of the following items.  
Indicates that incorrect handling may cause  
hazardous conditions, resulting in death or  
CAUTION  
DANGER  
severe injury.  
z
z
Do not disassemble or modify any unit.  
This will cause failure, malfunction, injuries, or fire.  
Product name  
Quantity  
Indicates that incorrect handling may cause  
CAUTION hazardous conditions, resulting in medium or  
slight personal injury or physical damage.  
Do not touch the conductive areas and electronic parts of this  
unit directly.  
Doing so can cause a unit malfunction or failure.  
Any one of GT15-75QBUSL,  
GT15-75QBUS2L, GT15-75ABUSL,  
GT15-75ABUS2L  
1
z
Always secure the cables connected to the unit, e.g. run them in  
conduits or clamp them.Not doing so can cause unit or cable  
damage due to dangling, moved or accidentally pulled cables or  
can cause a malfunction due to a cable contact fault.  
Seals  
12  
Note that the  
CAUTION level may lead to a serious accident  
according to the circumstances.  
Always follow the precautions of both levels because they are impor-  
tant to personal safety.  
Please save this manual to make it accessible when required and  
always forward it to the end user.  
z
z
Do not hold the cable part when unplugging any cable  
connected to the unit. Doing so can cause unit or cable damage  
or a malfunction due to a cable contact fault.  
Always make sure to touch the grounded metal to discharge the  
electricity charged in the body, etc., before touching the unit.  
Failure to do so may cause a failure or malfunctions of the unit.  
Warranty  
2. Specifications  
3. Part Names and External Dimensions  
4. Installation Procedure  
Mitsubishi will not be held liable for damage caused by factors found  
not to be the cause of Mitsubishi; machine damage or lost profits  
caused by faults in the Mitsubishi products; damage, secondary  
damage, accident compensation caused by special factors  
unpredictable by Mitsubishi; damages to products other than  
Mitsubishi products; and to other duties.  
The performance specifications of the bus connection unit are  
indicated below.  
Refer to the used GT15 User's Manual for the general  
specifications of the bus connection unit.  
(1) Power off the GOT.  
136.8(5.39)  
(2) Remove the two expansion unit covers of the GOT.  
For safe use  
This product has been manufactured as a general-purpose part for  
general industries, and has not been designed or manufactured to  
be incorporated in a device or system used in purposes related to  
human life.  
GT15-  
GT15-  
GT15-  
GT15-  
4)  
5)  
Item  
75QBUSL 75QBUS2L 75ABUSL 75ABUS2L  
I/O  
occupied  
points  
16 points (I/O assignment: 32 points (I/O assignment:  
16 intelligent points)  
Before using the product for special purposes such as nuclear  
power, electric power, aerospace, medicine or passenger  
movement vehicles, consult with Mitsubishi.  
This product has been manufactured under strict quality control.  
However, when installing the product where major accidents or  
losses could occur if the product fails, install appropriate backup or  
failsafe functions in the system.  
Special 32 points)  
4)  
Internal  
consumed  
current  
0.44A  
0.44A  
0.12A  
0.12A  
(DC5V)*  
Weight  
0.13kg  
0.14kg  
0.13kg  
0.14kg  
(3) Fit the bus connection unit along the groove of the  
GOT case.  
Country/Region Sales office/Tel  
U.S.A  
Mitsubishi Electric Automation Inc.  
500 Corporate Woods Parkway Vernon Hills, IL 60061  
Tel : +1-847-478-2100  
*
When the GOT power is on, the internal current consumption is  
included in the current consumption of the GOT.  
When the GOT power is off, the internal current is supplied from  
the power supply of the PLC system.  
Brazil  
MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda.  
Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar  
Paraiso, Sao Paulo, SP Brazil  
*1  
2)  
Back view  
1)  
Tel : +55-11-5908-8331  
Germany  
U.K  
Mitsubishi Electric Europe B.V. German Branch  
Gothaer Strasse 8 D-40880 Ratingen, GERMANY  
Tel : +49-2102-486-0  
Mitsubishi Electric Europe B.V. UK Branch  
Travellers Lane, Hatfield, Herts., AL10 8XB,UK  
Tel : +44-1707-276100  
3)  
Italy  
Mitsubishi Electric Europe B.V. Italian Branch  
Centro Dir. Colleoni, Pal. Perseo-Ingr.2  
Via Paracelso 12, 20041 Agrate B., Milano, Italy  
Tel : +39-039-6053344  
Spain  
Mitsubishi Electric Europe B.V. Spanish Branch  
Carretera de Rubi 76-80  
08190 - Sant Cugat del Valles, Barcelona, Spain  
Tel : +34-93-565-3131  
France  
Mitsubishi Electric Europe B.V. French Branch  
25 Boulevard des Bouvets, F-92741 Nanterre Cedex, France  
TEL: +33-1-5568-5568  
South Africa  
Hong Kong  
Circuit Breaker Industries LTD.  
Tripswitch Drive, Elandsfontein Gauteng, South Africa  
Tel : +27-11-928-2000  
Ryoden Automation Ltd.  
10th Floor, Manulife Tower, 169 Electric  
Road, North Point, HongKong  
Tel : +852-2887-8870  
(4) Fasten the bus connection unit by tightening its  
mounting screws (4 places) with tightening torgue  
0.36 to 0.48 N•m.  
MODEL  
GT15- 75QBUSL  
GT15- 75QBUS2L  
GT15- 75ABUSL  
GT15- 75ABUS2L  
A
China  
Ryoden Automation Shanghai Ltd.  
3F Block5 Building Automation  
Instrumentation Plaza 103 Cao Bao Rd. Shanghai 200233 China  
Tel : +86-21-6120-0808  
Setsuyo Enterprise Co., Ltd.  
6F., No.105 Wu-Kung 3rd.RD, Wu-Ku Hsiang,  
Taipei Hsine, Taiwan  
Tel : +886-2-2299-2499  
HAN NEUNG TECHNO CO.,LTD.  
1F Dong Seo Game Channel Bldg.,660-11, Deungchon-dong  
Kangsec-ku, Seoul, Korea  
Tel : +82-2-3660-9552  
Mitsubishi Electric Asia Pte, Ltd.  
307 Alexandra Road #05-01/02,  
Mitsubishi Electric Building Singapore 159943  
Tel : +65-6473-2308  
F. A. Tech Co.,Ltd.  
898/28,29,30 S.V.City Building,Office Tower 2, Floor 17-18 Rama 3  
Road, Bangkpongpang, Yannawa, Bangkok 10120  
Tel : +66-2-682-6522  
P.T. Autoteknindo SUMBER MAKMUR  
Jl. Muara Karang Selatan Block a Utara No.1 Kav. No.11 Kawasan  
Industri/Pergudangan Jakarta - Utara 14440  
Tel : +62-21-663-0833  
2.3(0.09)  
2.3(0.09)  
3.9(0.15)  
Taiwan  
Korea  
3.9(0.15)  
Unit: mm (inch)  
*1 When the GT15-75QBUSL/GT15-75ABUSL is used, only the IN  
side connector is available.  
Singapore  
Thailand  
Indonesia  
India  
No.  
1)  
Name  
Description  
Connector for connecting the  
bus connection cable (IN side)  
(5) After tightening screws, attach the supplied seals.  
Bus connector (IN side)  
Bus connector (OUT  
side)  
Connector for connecting the  
bus connection cable (OUT side)  
2)  
3)  
Messung Systems Put,Ltd.  
Electronic Sadan NO:111 Unit No15, M.I.D.C BHOSARI,  
PUNE-411026, India  
Tel : +91-20-712-2807  
Mitsubishi Electric Australia Pty. Ltd.  
348 Victoria Road, PostalBag, No 2,  
Rydalmere, N.S.W 2116, Australia  
Tel : +61-2-9684-7777  
For connecting the extended  
connector of the GOT  
Extended connector  
Australia  
Screw (M3 screw) for fixing the  
unit to the GOT  
4)  
5)  
Mounting screw  
Rating plate  
-
HEAD OFFICE : 1-8-12, OFFICE TOWER Z 14F HARUMI CHUO-KU 104-6212,JAPAN  
NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN  
When exported from Japan, this manual does not require application to the Ministry  
of Economy, Trade and Industry for service transaction permission.  
Specifications subject to change without notice.  
Printed in Japan on recycled paper.  

IBM Rack Mount Industrial Monitor HIS RL17 User Manual
Intel DFI R120 User Manual
Kambrook SNACK OVEN KOT65 User Manual
LG Electronics LG Life Good Computer Monitor L227WT User Manual
Memorex MPH6925 User Manual
M Systems Flash Disk Pioneers DVR 115DBK User Manual
Nvidia TEGRA DG 04927 001_V01 User Manual
Panasonic TC 20B10P User Manual
Philips 1 92E+04 User Manual
Philips Computer Monitor 220BI User Manual