Lenovo V200 User Manual

Lenovo 3000 V100 and V200  
Hardware Maintenance Manual  
May 2007  
This manual supports:  
Lenovo 3000 V100 and V200  
(MT 0763 and 0764)  
Lenovo 3000 V100 and V200  
Hardware Maintenance Manual  
Note  
Before using this information and the product it supports, be sure to read the general information under “Notices” on page  
First Edition (May 2007)  
© Copyright Lenovo 2007. All rights reserved.  
U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with  
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule  
contract with Lenovo, if any, or the standard terms of this commercial license, or if the agency is  
unable to accept this Program under these terms, then we provide this Program under the provisions set forth in  
Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in  
Data-General, FAR 52.227.14 (Alternate III).  
Contents  
© Copyright Lenovo 2007  
iii  
iv MT 0763 and 0764  
Introduction  
About this manual  
This manual contains service and reference information for Lenovo 3000 V100 and  
V200 (MT 0763 and 0764). Use this manual along with the advanced diagnostic  
tests to troubleshoot problems.  
The manual is divided into sections as follows:  
v The common sections provide general information, guidelines, and safety  
information required in servicing computers.  
v The product-specific section includes service, reference, and product-specific  
parts information.  
Important  
This manual is intended for trained service personnel who are familiar with  
Lenovo 3000 products. Use this manual along with the advanced diagnostic  
tests to troubleshoot problems effectively.  
Before servicing a Lenovo 3000 product, be sure to review the safety  
Important service information  
Important  
BIOS and device driver fixes are customer-installable. The BIOS and device  
drivers are posted on the customer support site http://www.lenovo.com/  
Advise customers to contact the Customer Support Center at 800-426-7378 if  
they need assistance in obtaining or installing any software fixes, drivers, and  
BIOS downloads.  
Customers in Canada should call the Customer Support Center at  
800-565-3344 for assistance or download information.  
Strategy for replacing FRUs  
Before replacing parts  
Make sure that all software fixes, drivers, and BIOS downloads are installed  
before replacing any FRUs listed in this manual.  
Use the following strategy to prevent unnecessary expense for replacing and  
servicing FRUs:  
© Copyright Lenovo 2007  
1
 
Important service information  
v If you are instructed to replace a FRU but the replacement does not correct the  
problem, reinstall the original FRU before you continue.  
v Some computers have both a processor board and a system board. If you are  
instructed to replace either the processor board or the system board, and  
replacing one of them does not correct the problem, reinstall that board, and  
then replace the other one.  
v If an adapter or a device consists of more than one FRU, any of the FRUs may  
be the cause of the error. Before replacing the adapter or device, remove the  
FRUs, one by one, to see if the symptoms change. Replace only the FRU that  
changed the symptoms.  
Attention: The setup configuration on the computer you are servicing may have  
been customized. Running Automatic Configuration may alter the settings. Note  
the current configuration settings (using the View Configuration option); then,  
when service has been completed, verify that those settings remain in effect.  
Strategy for replacing a hard disk drive  
Always try to run a low-level format before replacing a hard disk drive.  
Attention: The drive startup sequence in the computer you are servicing may  
have been changed. Be extremely careful during write operations such as copying,  
saving, or formatting. If you select an incorrect drive, data or programs can be  
overwritten.  
Important notice for replacing a system board  
Some components mounted on a system board are very sensitive. Improper  
handling of a system board can cause damage to those components, and may  
cause a system malfunction.  
Attention: When handling a system board:  
v Do not drop a system board or apply any excessive force to it.  
v Avoid rough handling of any kind.  
v Avoid bending a system board and hard pushing to prevent cracking at each  
BGA (Ball Grid Array) chipset.  
How to use error messages  
Use the error codes displayed on the screen to diagnose failures. If more than one  
error code is displayed, begin the diagnosis with the first error code. Whatever  
causes the first error code may also cause false error codes. If no error code is  
displayed, see whether the error symptom is listed in the Symptom-to-FRU Index  
for the computer you are servicing.  
Strategy for replacing FRUs for Custom Model Variant (CMV) products  
Custom Model Variant (CMV) is a unique configuration that has been negotiated  
between LenovoTM and the customer. A unique 4-digit MT and 3-digit model is  
provided to the customer to place orders (Example: 1829-W15). A CMV is a special  
bid offering. Therefore, it is NOT generally announced.  
There are three information resources to identify which FRUs are used to support  
CMV products. These sources are PC Entitlement Warehouse (PEW), eSupport, and  
the HMM.  
2
MT 0763 and 0764  
 
Important service information  
Using PC Entitlement Warehouse (PEW)  
v PEW is the primary source for identifying FRU part numbers and FRU  
descriptions for the key commodities for CMV products at a MT - serial number  
level. An example of key commodities are hard disk drives, system boards,  
microprocessors, Liquid Crystal Displays (LCDs), and memory.  
v Remember, all CMV products are loaded in PEW under the 4-digit MT and  
3-digit model, where model = “fixed part number”.  
v PEW can be accessed at the following Web site:  
Customers can also access PEW via  
Click on MACHINE LOOKUP, followed by WARRANTY INFORMATION. Input  
the MT and the Serial number and the list of key commodities will be returned  
in the PEW record under COMPONENT INFORMATION.  
v Business Partners using Eclaim will access PEW when performing Entitlement  
Lookup. Business Partners will enter Loc ID, MT and Serial, and the key  
commodities will be returned in the Eclaim record under SYSTEM DETAILS.  
v Authorized IBM® Business Partners can access Eclaim at the following Web site:  
Using eSupport  
For Key Commodities (Examples - hard disk drive, system board,  
microprocessor, LCD, and memory)  
v eSupport can be used to view the list of key commodities built in a particular  
machine serial (this is the same record found in PEW).  
v eSupport can be accessed at the following Web site: http://www.lenovo.com/  
v To view the key commodities, click on PARTS INFORMATION, then PARTS  
LOOKUP. Type in the model type and serial number. The key commodities will  
be returned in the eSupport record under PARTS SHIPPED WITH YOUR  
SYSTEM.  
For the Remaining FRUs (the complete list of FRUs at the MT Model level)  
v eSupport can be used to view the complete list of FRUs for a machine type and  
model.  
v To view the complete list of FRUs, type in the machine type and model  
(Example: 1829-CTO) under QUICK PATH. Under “View by Document Type”  
select PARTS INFORMATION. Under “Filter by Category” select SERVICE  
PARTS. Under “Parts Information by Date” select SYSTEM SERVICE PARTS. The  
list of service parts by description, with applicable machine type model and FRU  
will be displayed.  
Using the HMM  
Use the HMM as a back-up to PEW and eSupport to view the complete list of  
FRUs at the MT Model level. CMVs are custom models and are not found in the  
HMM.  
Introduction  
3
 
Important service information  
Important information about replacing RoHS compliant FRUs  
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic  
Equipment Directive (2002/95/EC) is a European Union legal requirement  
affecting the global electronics industry. RoHS requirements must be  
implemented on Lenovo products placed on the market after June 2006. Products  
on the market before June 2006 are not required to have RoHS compliant parts.  
So, if the original FRU parts are non compliant, replacement parts can also be  
non compliant. In all cases if the original FRU parts are RoHS compliant the  
replacement part must also be RoHS compliant.  
Lenovo plans to transition to RoHS compliance well before the implementation  
date and expects its suppliers to be ready to support Lenovo's requirements and  
schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The  
following statement pertains to these products and any product Lenovo produces  
containing RoHS compliant FRUs.  
RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS  
implementation date, failed RoHS compliant parts must always be replaced using  
RoHS compliant FRUs, so only the FRUs identified as compliant in the system  
HMM or direct substitutions for those FRUs may be used.  
Products marketed before June 2006  
Products marketed after June 2006  
Current or original  
part  
Replacement FRU  
Current or original  
part  
Replacement FRU  
Non-RoHS  
Non-RoHS  
Non-RoHS  
RoHS  
Can be Non-RoHS  
Can be RoHS  
Must be RoHS  
Must be RoHS  
Can sub to RoHS  
Must be RoHS  
Note: A direct substitution is a part with a different FRU part number that is  
automatically shipped by the distribution center at the time of the order.  
4
MT 0763 and 0764  
 
Diskette compatibility matrix  
Diskette compatibility matrix  
The compatibility of each of the drives with the diskettes for it is as follows:  
Diskette  
drive  
Diskette  
capacity  
Compatibility  
3.5-inch  
1.0 MB  
2.0 MB  
4.0 MB  
Read and write  
Read and write  
Not compatible  
Safety notices: multilingual translations  
In this manual, safety notices appear in English with a page number reference to  
the appropriate multilingual, translated safety notice found in this section.  
The following safety notices are provided in English, French, German, Hebrew,  
Italian, and Spanish.  
Safety notice 1  
Before the computer is powered on after FRU replacement, make sure all screws, springs,  
and other small parts are in place and are not left loose inside the computer. Verify this  
by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes  
can cause electrical shorts.  
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle,  
vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour  
ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces  
métalliques ou des copeaux de métal pourraient causer un court-circuit.  
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß  
sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im  
Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche  
geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen.  
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una FRU,  
accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella  
corretta posizione e non siano sparse all’interno dell’elaboratore. Verificare ciò scuotendo  
l’elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti  
metallici possono provocare cortocircuiti pericolosi.  
Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los  
tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran  
sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles  
ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.  
Introduction  
5
 
Safety notices  
Safety notice 2  
DANGER  
Some standby batteries contain a small amount of nickel and cadmium. Do not  
disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.  
Dispose of the battery as required by local ordinances or regulations. Use only the  
battery in the appropriate parts listing. Use of an incorrect battery can result in  
ignition or explosion of the battery.  
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez  
pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne les mettez pas en  
court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur.  
Lorsque vous remplacez la pile de sauvegarde ou celle de l’horloge temps réel, veillez  
à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une  
batterie ou une pile inappropriée risque de prendre feu ou d’exploser.  
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann  
geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle  
oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt,  
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die  
Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der  
Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der  
Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der  
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder  
Explosion führen.  
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non  
smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle  
secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni  
locali). Quando si sostituisce la batteria dell’RTC (real time clock) o la batteria di  
supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di  
una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria  
stessa.  
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No  
las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.  
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se  
encuentren en la lista de piezas. La utilización de una batería no apropiada puede  
provocar la ignición o explosión de la misma.  
6
MT 0763 and 0764  
Safety notices  
Safety notice 3  
DANGER  
The battery pack contains small amounts of nickel. Do not disassemble it, throw it  
into fire or water, or short-circuit it. Dispose of the battery pack as required by local  
ordinances or regulations. Use only the battery in the appropriate parts listing when  
replacing the battery pack. Use of an incorrect battery can result in ignition or  
explosion of the battery.  
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.  
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la  
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser que  
les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie  
inappropriée risque de prendre feu ou d’exploser.  
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,  
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei  
der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen  
der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist.  
Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.  
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o  
nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82,  
successive disposizioni e disposizioni locali). Quando si sostituisce la batteria,  
utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una  
batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.  
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue,  
ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la  
normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al  
sustituir la batería. La utilización de una batería no apropiada puede provocar la  
ignición o explosión de la misma.  
Introduction  
7
Safety notices  
Safety notice 4  
DANGER  
The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it,  
remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate  
it, or expose its cell contents to water. Dispose of the battery as required by local  
ordinances or regulations. Use only the battery in the appropriate parts listing. Use of  
an incorrect battery can result in ignition or explosion of the battery.  
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,  
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur  
polarisé et ne la démontez pas. Ne l’exposez pas à une temperature supérieure à 100°C,  
ne la faites pas brûler et n’en exposez pas le contenu à l’eau. Mettez la pile au rebut  
conformément à la réglementation en vigueur. Une pile inappropriée risque de  
prendre feu ou d’exploser.  
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren  
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht  
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt  
nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte  
Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen  
für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs  
verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien  
kann zu Entzündung oder Explosion führen.  
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare  
gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla,  
riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla  
in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive  
disposizioni e disposizioni locali). L’impiego di una batteria non adatta potrebbe  
determinare l’incendio o l’esplosione della batteria stessa.  
La batería de repuesto es una batería de litio y puede provocar incendios, explosiones  
o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte,  
ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de  
sus celdas al agua. Deséchela tal como dispone la normativa local.  
8
MT 0763 and 0764  
Safety notices  
Safety notice 5  
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your  
hands, immediately wash the affected areas with water for at least 15 minutes. Seek  
medical care if any symptoms from the fluid are present after washing.  
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux  
ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze  
minutes. Consultez un médecin si des symptômes persistent après le lavage.  
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die  
örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas  
und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den  
Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in  
Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15  
Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht  
werden.  
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto entrasse in  
contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua  
corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero  
permanere.  
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos,  
lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo.  
Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse.  
Safety notice 6  
DANGER  
To avoid shock, do not remove the plastic cover that protects the lower part of the  
inverter card.  
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique  
protégeant la partie inférieure de la carte d’alimentation.  
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der  
Spannungswandlerplatine umgibt, nicht entfernen.  
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la  
parte inferiore della scheda invertitore.  
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la  
tarjeta invertida.  
Introduction  
9
Safety notices  
Safety notice 7  
DANGER  
Though the main batteries have low voltage, a shorted or grounded battery can  
produce enough current to burn personnel or combustible materials.  
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise  
à la masse d’une batterie peut produire suffisamment de courant pour brûler des  
matériaux combustibles ou causer des brûlures corporelles graves.  
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei  
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu  
entzünden oder Verletzungen bei Personen hervorzurufen.  
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto  
circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o  
provocare ustioni ai tecnici di manutenzione.  
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o  
con contacto a tierra puede producir la corriente suficiente como para quemar material  
combustible o provocar quemaduras en el personal.  
Safety notice 8  
DANGER  
Before removing any FRU, power off the computer, unplug all power cords from  
electrical outlets, remove the battery pack, and then disconnect any interconnecting  
cables.  
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,  
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la  
batterie et déconnectez tous les cordons d’interface.  
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der  
Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt  
wird.  
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche  
tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di  
interconnessione.  
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas  
de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de  
conexión entre dispositivos.  
10 MT 0763 and 0764  
Safety information  
Safety information  
The following section presents safety information with which you need to be  
familiar before you service a Lenovo 3000 computer.  
General safety  
Follow these rules to ensure general safety:  
v Observe good housekeeping in the area of the machines during and after  
maintenance.  
v When lifting any heavy object:  
1. Make sure that you can stand safely without slipping.  
2. Distribute the weight of the object equally between your feet.  
3. Use a slow lifting force. Never move suddenly or twist when you attempt to  
lift.  
4. Lift by standing or by pushing up with your leg muscles; this action removes  
the strain from the muscles in your back. Do not attempt to lift any object that  
weighs more than 16 kg (35 lb) or that you think is too heavy for you.  
v Do not perform any action that causes hazards to the customer, or that makes  
the equipment unsafe.  
v Before you start the machine, make sure that other service representatives and  
the customer’s personnel are not in a hazardous position.  
v Place removed covers and other parts in a safe place, away from all personnel,  
while you are servicing the machine.  
v Keep your toolcase away from walk areas so that other people will not trip over  
it.  
v Do not wear loose clothing that can be trapped in the moving parts of a  
machine. Make sure that your sleeves are fastened or rolled up above your  
elbows. If your hair is long, fasten it.  
v Insert the ends of your necktie or scarf inside clothing or fasten it with a  
nonconductive clip, about 8 centimeters (3 inches) from the end.  
v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your  
clothing.  
Attention: Metal objects are good electrical conductors.  
v Wear safety glasses when you are hammering, drilling, soldering, cutting wire,  
attaching springs, using solvents, or working in any other conditions that might  
be hazardous to your eyes.  
v After service, reinstall all safety shields, guards, labels, and ground wires.  
Replace any safety device that is worn or defective.  
v Reinstall all covers correctly before returning the machine to the customer.  
v Fan louvers on the machine help to prevent overheating of internal components.  
Do not obstruct fan louvers or cover them with labels or stickers.  
Electrical safety  
Observe the following rules when working on electrical equipment.  
Introduction 11  
 
Safety information  
Important  
Use only approved tools and test equipment. Some hand tools have handles  
covered with a soft material that does not insulate you when working with  
live electrical currents.  
Many customers have, near their equipment, rubber floor mats that contain  
small conductive fibers to decrease electrostatic discharges. Do not use this  
type of mat to protect yourself from electrical shock.  
v Find the room emergency power-off (EPO) switch, disconnecting switch, or  
electrical outlet. If an electrical accident occurs, you can then operate the switch  
or unplug the power cord quickly.  
v Do not work alone under hazardous conditions or near equipment that has  
hazardous voltages.  
v Disconnect all power before:  
– Performing a mechanical inspection  
Working near power supplies  
– Removing or installing main units  
v Before you start to work on the machine, unplug the power cord. If you cannot  
unplug it, ask the customer to power-off the wall box that supplies power to the  
machine, and to lock the wall box in the off position.  
v If you need to work on a machine that has exposed electrical circuits, observe the  
following precautions:  
– Ensure that another person, familiar with the power-off controls, is near you.  
Attention: Another person must be there to switch off the power, if  
necessary.  
– Use only one hand when working with powered-on electrical equipment;  
keep the other hand in your pocket or behind your back.  
Attention: An electrical shock can occur only when there is a complete  
circuit. By observing the above rule, you may prevent a current from passing  
through your body.  
– When using testers, set the controls correctly and use the approved probe  
leads and accessories for that tester.  
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you  
from grounds such as metal floor strips and machine frames.  
Observe the special safety precautions when you work with very high voltages;  
Instructions for these precautions are in the safety sections of maintenance  
information. Use extreme care when measuring high voltages.  
v Regularly inspect and maintain your electrical hand tools for safe operational  
condition.  
v Do not use worn or broken tools and testers.  
v Never assume that power has been disconnected from a circuit. First, check that it  
has been powered off.  
v Always look carefully for possible hazards in your work area. Examples of these  
hazards are moist floors, nongrounded power extension cables, power surges,  
and missing safety grounds.  
v Do not touch live electrical circuits with the reflective surface of a plastic dental  
mirror. The surface is conductive; such touching can cause personal injury and  
machine damage.  
12 MT 0763 and 0764  
Safety information  
v Do not service the following parts with the power on when they are removed  
from their normal operating places in a machine:  
– Power supply units  
– Pumps  
– Blowers and fans  
– Motor generators  
and similar units. (This practice ensures correct grounding of the units.)  
v If an electrical accident occurs:  
– Use caution; do not become a victim yourself.  
– Switch off power.  
– Send another person to get medical aid.  
Safety inspection guide  
The purpose of this inspection guide is to assist you in identifying potentially  
unsafe conditions. As each machine was designed and built, required safety items  
were installed to protect users and service personnel from injury. This guide  
addresses only those items. You should use good judgment to identify potential  
safety hazards due to attachment of non-Lenovo 3000 features or options not  
covered by this inspection guide.  
If any unsafe conditions are present, you must determine how serious the apparent  
hazard could be and whether you can continue without first correcting the  
problem.  
Consider these conditions and the safety hazards they present:  
v Electrical hazards, especially primary power (primary voltage on the frame can  
cause serious or fatal electrical shock)  
v Explosive hazards, such as a damaged CRT face or a bulging capacitor  
v Mechanical hazards, such as loose or missing hardware  
To determine whether there are any potentially unsafe conditions, use the  
following checklist at the beginning of every service task. Begin the checks with  
the power off, and the power cord disconnected.  
Checklist:  
1. Check exterior covers for damage (loose, broken, or sharp edges).  
2. Power off the computer. Disconnect the power cord.  
3. Check the power cord for:  
a. A third-wire ground connector in good condition. Use a meter to measure  
third-wire ground continuity for 0.1 ohm or less between the external  
ground pin and the frame ground.  
b. The power cord should be the type specified in the parts list.  
c. Insulation must not be frayed or worn.  
4. Remove the cover.  
5. Check for any obvious non-Lenovo 3000 alterations. Use good judgment as to  
the safety of any non-Lenovo 3000 alterations.  
6. Check inside the unit for any obvious unsafe conditions, such as metal filings,  
contamination, water or other liquids, or signs of fire or smoke damage.  
7. Check for worn, frayed, or pinched cables.  
8. Check that the power-supply cover fasteners (screws or rivets) have not been  
removed or tampered with.  
Introduction 13  
 
Safety information  
Handling devices that are sensitive to electrostatic discharge  
Any computer part containing transistors or integrated circuits (ICs) should be  
considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when  
there is a difference in charge between objects. Protect against ESD damage by  
equalizing the charge so that the machine, the part, the work mat, and the person  
handling the part are all at the same charge.  
Notes  
1. Use product-specific ESD procedures when they exceed the requirements  
noted here.  
2. Make sure that the ESD protective devices you use have been certified  
(ISO 9000) as fully effective.  
When handling ESD-sensitive parts:  
v Keep the parts in protective packages until they are inserted into the product.  
v Avoid contact with other people.  
v Wear a grounded wrist strap against your skin to eliminate static on your body.  
v Prevent the part from touching your clothing. Most clothing is insulative and  
retains a charge even when you are wearing a wrist strap.  
v Use the black side of a grounded work mat to provide a static-free work surface.  
The mat is especially useful when handling ESD-sensitive devices.  
v Select a grounding system, such as those listed below, to provide protection that  
meets the specific service requirement.  
Note  
The use of a grounding system to guard against ESD damage is desirable  
but not necessary.  
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire  
ground.  
– When working on a double-insulated or battery-operated system, use an ESD  
common ground or reference point. You can use coax or connector-outside  
shells on these systems.  
– Use the round ground prong of the ac plug on ac-operated computers.  
Grounding requirements  
Electrical grounding of the computer is required for operator safety and correct  
system function. Proper grounding of the electrical outlet can be verified by a  
certified electrician.  
14 MT 0763 and 0764  
 
Laser compliance statement  
Laser compliance statement  
Some models of Lenovo 3000 computer are equipped from the factory with an  
optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such  
devices are also sold separately as options. If one of these drives is installed, it is  
certified in the U.S. to conform to the requirements of the Department of Health  
and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J  
for Class 1 laser products. Elsewhere, the drive is certified to conform to the  
requirements of the International Electrotechnical Commission (IEC) 825 and  
CENELEC EN 60 825 for Class 1 laser products.  
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note  
the following:  
CAUTION:  
Use of controls or adjustments or performance of procedures other than those  
specified herein might result in hazardous radiation exposure.  
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui  
especificados pode resultar em perigosa exposição à radiação.  
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de réglage  
et d’utilisation des commandes, ainsi que les procédures décrites.  
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann  
gefährliche Laserstrahlung auftreten.  
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle  
specificate possono provocare l’esposizione a.  
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí  
especificados puede provocar la exposición a radiaciones peligrosas.  
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage  
device could result in exposure to hazardous laser radiation. There are no  
serviceable parts inside those drives. Do not open.  
Introduction 15  
 
Laser compliance statement  
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may  
contain an embedded Class 3A or Class 3B laser diode. Note the following:  
DANGER  
Emits visible and invisible laser radiation when open. Do not stare into the beam, do  
not view directly with optical instruments, and avoid direct exposure to the beam.  
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente  
por meio de instrumentos óticos e evite exposição direta com o feixe de luz.  
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder  
directement avec des instruments optiques, ou de vous exposer au rayon.  
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente in  
den Laserstrahl sehen und den Strahlungsbereich meiden.  
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai eszközökkel.  
Kerülje a sugárnyalábbal való érintkezést !  
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo  
direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.  
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz  
de luz. Evite la exposición directa al haz.  
16 MT 0763 and 0764  
General descriptions  
The descriptions in this chapter apply to any Lenovo 3000 model that has the  
PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to  
your particular computer.  
Read this first  
Before you go to the checkout guide, be sure to read this section.  
Important notes  
v Only certified trained personnel should service the computer.  
v Before replacing any FRU, read the entire page on removing and  
replacing FRUs.  
v When you replace FRUs, use new nylon-coated screws.  
v Be extremely careful during such write operations as copying, saving, or  
formatting. Drives in the computer that you are servicing sequence might  
have been altered. If you select an incorrect drive, data or programs might  
be overwritten.  
v Replace a FRU only with another FRU of the correct model. When you  
replace a FRU, make sure that the model of the machine and the FRU part  
number are correct by referring to the FRU parts list.  
v A FRU should not be replaced because of a single, unreproducible  
failure. Single failures can occur for a variety of reasons that have nothing  
to do with a hardware defect, such as cosmic radiation, electrostatic  
discharge, or software errors. Consider replacing a FRU only when a  
problem recurs. If you suspect that a FRU is defective, clear the error log  
and run the test again. If the error does not recur, do not replace the FRU.  
v Be careful not to replace a nondefective FRU.  
What to do first  
When you do return a FRU, you must include the following information in the  
parts exchange form or parts return form that you attach to it:  
__ 1. Name and phone number of servicer  
__ 2. Date of service  
__ 3. Date on which the machine failed  
__ 4. Date of purchase  
__ 5. Failure symptoms, error codes appearing on the display  
__ 6. Procedure index and page number in which the failing FRU was detected  
__ 7. Failing FRU name and part number  
__ 8. Machine type, model number, and serial number  
__ 9. Customer’s name and address  
Note for warranty:  
During the warranty period, the customer may be responsible for repair costs if the  
computer damage was caused by misuse, accident, modification, unsuitable  
physical or operating environment, or improper maintenance by the customer.  
© Copyright Lenovo 2007  
17  
 
Read this first  
Following is a list of some common items that are not covered under warranty and  
some symptoms that might indicate that the system was subjected to stress beyond  
normal use.  
Before checking problems with the computer, determine whether the damage is  
covered under the warranty by referring to the following list:  
The following are not covered under warranty:  
v LCD panel cracked from the application of excessive force or from being  
dropped  
v Scratched (cosmetic) parts  
v Distortion, deformation, or discoloration of the cosmetic parts  
v Plastic parts, latches, pins, or connectors that have been cracked or broken by  
excessive force  
v Damage caused by liquid spilled into the system  
v Damage caused by the improper insertion of a PC Card or the installation of an  
incompatible card  
v Improper disc insertion or use of an optical drive  
v Diskette drive damage caused by pressure on the diskette drive cover, foreign  
material in the drive, or the insertion of a diskette with multiple labels  
v Damaged or bent diskette eject button  
v Fuses blown by attachment of a nonsupported device  
v Forgotten computer password (making the computer unusable)  
v Sticky keys caused by spilling a liquid onto the keyboard  
v Use of an incorrect ac adapter on laptop products  
The following symptoms might indicate damage caused by nonwarranted  
activities:  
v Missing parts might be a symptom of unauthorized service or modification.  
v If the spindle of a hard disk drive becomes noisy, it may have been subjected to  
excessive force, or dropped.  
18 MT 0763 and 0764  
Related service information  
Related service information  
This section provides information about the following:  
Service Web site  
When the latest maintenance diskette and the system program service diskette  
become available, they will be posted on http://www.lenovo.com/spm  
Restoring the factory contents by using Product Recovery  
discs  
When the hard disk drive is replaced because of a failure, no Product Recovery  
program is on the new hard disk. In this case, you must use the recovery disc for  
the computer. Order the recovery disc and the hard disk drive at the same time so  
that you can recover the new hard disk drive with the preinstalled software when  
they arrive. For information on which disc to order, see “Recovery discs” on page  
To install the factory contents by using Product Recovery discs, do the following:  
Note  
The recovery process might take up to 2 hours.  
1. Make the optical drive the first start up device in the startup sequence.  
2. Insert the bootable Rescue and RecoveryStartup disc into the optical drive,  
and then start the computer.  
3. In the Rescue and Recovery workspace, complete the following procedure:  
a. When the Rescue and Recovery workspace opens, click Continue on the  
Welcome window and then click Restore your system.  
b. When a message about accessing a USB device is displayed, click OK.  
c. In the initial window of the Restore your systemwizard, select Restore  
my hard drive to the original factory state and click Next.  
d. In the next window, select I do not want to save any files and click Next.  
e. A warning opens not to turn off the computer during the recovery process.  
Click OK.  
4. When the Product Recovery window opens, click OK.  
5. The Terms and Conditions window opens, select I accept these terms and  
conditions and then click OK.  
6. After the files necessary for the product recovery are copied from the Rescue  
and Recovery Startup disc to the hard drive, the system restarts automatically  
and boot back into Rescue and Recovery. Remove the disc and turn off the  
computer.  
7. Turn on the computer to continue the recovery process.  
8. After you restart the computer, the computer prompts you for a supplemental  
Rescue and Recovery disc. If you have a supplemental Rescue and Recovery  
disc, click OK and insert the supplemental disc. If you do not have a  
supplemental disc, click No.  
General descriptions 19  
 
Related service information  
9. When prompted, insert the appropriate Product Recovery disc and then click  
OK. The second phase of the recovery process begins.  
10. When all of the data has been copied from the last Product Recovery disc in  
the set, a message is displayed prompting you to restart the computer.  
Remove the disc and then click Yes, then a message is displayed asking you  
to continue the recovery process. Click Continue to restart your computer,  
then the computer restarts and the third phase of the recovery process begins.  
11. When the recovery process is complete, the Welcome to Microsoft® Windows®  
screen is displayed. Follow the instructions on the screen to complete the  
Windows setup.  
Passwords  
As many as three passwords may be needed for any Lenovo 3000 computer: the  
power-on password (POP), the hard-disk password (HDP), and the supervisor  
password (SVP).  
If any of these passwords has been set, a prompt for it appears on the screen  
whenever the computer is turned on. The computer does not start until the  
password is entered.  
Exception: If only an SVP is installed or Password on Boot is disabled in the BIOS  
Setup Utility, the password prompt does not appear when the  
operating system is booted.  
Power-on password:  
A power-on password (POP) protects the system from being powered on by an  
unauthorized person. The password must be entered before an operating system  
can be booted.  
Hard-disk password:  
There are two hard-disk passwords (HDPs):  
v User HDP—for the user  
v Master HDP—for the system administrator, who can use it to get access to the  
hard disk even if the user has changed the user HDP  
Note: There are two modes for the HDP: User only and Master + User. The  
Master + User mode requires two HDPs; the system administrator enters  
both in the same operation. The system administrator then provides the user  
HDP to the system user.  
Attention: If the user HDP has been forgotten, check whether a master HDP has  
been set. If it has, it can be used for access to the hard disk drive. If no master  
HDP is available, neither Lenovo nor Lenovo authorized servicers provide any  
services to reset either the user or the master HDP, or to recover data from the  
hard disk drive. The hard disk drive can be replaced for a scheduled fee.  
Supervisor password:  
A supervisor password (SVP) protects the system information stored in the BIOS  
Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup  
Utility and change the system configuration.  
Attention: If the SVP has been forgotten and cannot be made available to the  
servicer, there is no service procedure to reset the password. The system board  
must be replaced for a scheduled fee.  
20 MT 0763 and 0764  
 
Related service information  
How to remove the power-on password  
To remove a POP that you have forgotten, do the following:  
(A) If an SVP is not known by the servicer:  
1. Turn off the computer.  
2. Remove the battery pack.  
For how to remove the battery pack, see “1010 Battery pack” on page 46.  
3. Remove the backup battery.  
For how to remove the backup battery, see “1050 Backup battery” on page 50.  
4. Turn on the computer and wait until the POST ends.  
After the POST ends, the password prompt does not appear. The POP has been  
removed.  
5. Reinstall the backup battery and the battery pack.  
(B) If an SVP is known by the servicer:  
1. Turn on the computer; then, while the initial screen is displayed, press the  
Lenovo CareSM button. The Rescue and Recovery screen opens.  
2. Click Access BIOS. The System Restart Required window is displayed.  
3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens.  
4. Select Security, using the cursor directional keys to move down the menu.  
5. Select Password.  
6. Select Power-On Password*1.  
7. Type the current SVP in the Enter Current Password field. Then leave the Enter  
New Password field blank, and press Enter twice.  
8. In the Changes have been saved window, press Enter.  
9. Press F10; then, in the Setup confirmation window, select Yes .  
Note: For some models, the BIOS menu marked *1 is User Password.  
How to remove the hard-disk password  
Attention: If User only mode is selected and the user HDP has been forgotten  
and cannot be made available to the servicer, neither Lenovo nor Lenovo  
authorized servicers provide any services to reset the user HDPs or to recover data  
from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.  
To remove a user HDP that has been forgotten, when the SVP and the master HDP  
are known, do the following:  
1. Turn on the computer; then, while the initial screen is displayed, press the  
Lenovo Care button. The Rescue and Recovery screen opens.  
2. Click Access BIOS. The System Restart Required window is displayed.  
3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens.  
4. Select Security, using the cursor directional keys to move down the menu.  
5. Select Password.  
6. Select Hard-disk x password, where x is the letter of the hard disk drive. A  
pop-up window opens.  
7. Select Master HDP.  
8. Type the current master HDP in the Enter Current Password field. then leave  
the Enter New Password field blank, and press Enter twice.  
9. Press F10.  
General descriptions 21  
Related service information  
10. Select Yes in the Setup Configuration window.  
Both user HDP and master HDP will have been removed.  
Power management  
Note: Power management modes are not supported for APM operating system.  
To reduce power consumption, the computer has three power management modes:  
screen blank, sleep (standby), and hibernation.  
Screen blank mode  
If the time set on the “Turn off monitor” timer in the operating system expires, the  
LCD backlight turns off.  
To end screen blank mode and resume normal operation, press any key.  
Sleep (standby) mode  
When the computer enters sleep (standby) mode, the following events occur in  
addition to what occurs in screen blank mode:  
v The LCD is powered off.  
v The hard disk drive is powered off.  
v The CPU stops.  
To enter sleep (standby) mode, press Fn+F4.  
In certain circumstances, the computer goes into sleep (standby) mode  
automatically:  
v If a “suspend time” has been set on the timer, and the user does not do any  
operation with the keyboard, the hard disk, the parallel connector, or the  
diskette drive within that time.  
v If the battery indicator blinks orange, indicating that the battery power is low.  
(Alternatively, if Hibernate when battery becomes low has been selected in the  
“Power Management Properties” window, the computer goes into hibernation  
mode.)  
To cause the computer to return from sleep (standby) mode and resume operation,  
do one of the following:  
v Press the Fn key.  
v Open the LCD cover.  
v Turn on the power switch.  
Also, in the following event, the computer automatically returns from sleep  
(standby) mode and resumes operation:  
v The time set on the resume timer elapses.  
Note: The computer does not accept any input immediately after it enters sleep  
(standby) mode. Wait a few seconds before taking any action to reenter  
operation mode.  
Hibernation mode  
In hibernation mode, the following occurs:  
v The system status, RAM, VRAM, and setup data are stored on the hard disk.  
v The system is powered off.  
22 MT 0763 and 0764  
 
Related service information  
To cause the computer to enter hibernation mode, do any of the following:  
v Press the Fn+F12 keys.  
v If you are using the ACPI operating system and have defined one of the  
following actions as the event that causes the system to go into hibernation  
mode, perform that action.  
– Closing the lid.  
– Pressing the power button.  
Also, the computer goes into hibernation mode automatically in either of the  
following conditions:  
v If a “hibernation time” has been set on the timer, and if the user does not do  
any operation with the keyboard, the hard disk drive, the parallel connector, or  
the diskette drive within that time.  
v If the timer conditions are satisfied in suspend mode.  
When the power is turned on, the computer returns from hibernation mode and  
resumes operation. The hibernation file in the boot record on the hard disk drive is  
read, and system status is restored from the hard disk drive.  
General descriptions 23  
Checkout guide  
Checkout guide  
Use the following procedures as a guide in identifying and correcting problems  
with the Lenovo 3000 computer.  
Note: The diagnostic tests are intended to test only Lenovo 3000 products. The use  
of non-Lenovo 3000 products, prototype cards, or modified options can lead  
to false indications of errors and invalid system responses.  
1. Identify the failing symptoms in as much detail as possible.  
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test  
or by repeating the operation.  
Testing the computer  
The Lenovo 3000 computer has a test program called PC-Doctor for DOS (hereafter  
called PC-Doctor.) You can detect errors by running the diagnostics test included in  
PC-Doctor. This section is an overview of the procedure. For details that depend  
on model-unique functions, refer to “Product overview” on page 30.  
For some possible configurations of the computer, PC-Doctor might not run  
correctly. To avoid this problem, you need to initialize the computer setup by use  
of the BIOS Setup Utility before you run PC-Doctor. On the BIOS Setup Utility  
screen, press F9, Enter, F10, and then Enter.  
Note: When you initialize the computer configuration, some devices are disabled,  
such as the serial port. If you test one of these devices, you will need to  
enable it by using Configuration utility for DOS. The utility is available on  
the following Web site: http://www.lenovo.com/support  
Creating the PC-Doctor diagnostics diskette  
To create the PC-Doctor disk from the Rescue and Recovery workspace , do as  
follows:  
1. Enter the Rescue and Recovery workspace by pressing the Lenovo Care button  
during POST.  
2. When the Rescue and Recovery workspace finishes loading, click Diagnostic  
Diskette.  
3. Authenticating the digital signature takes about 15 seconds; then the Lenovo  
3000 computer will reboot into PC-DOS.  
4. A batch file automatically starts up to prompt you through the process of  
creating diskettes. You are notified of how many diskettes you will need.  
a. You are prompted to insert each diskette in sequence.  
b. Typically, all you need to do is to press the Enter key for the floppy drive;  
the system then formats and creates the diskette.  
c. Each diskette is erased and formatted with the PC-Doctor for DOS boot  
image.  
5. Once all the diskettes have been created, the Lenovo 3000 computer will reboot.  
The user is asked to remove all diskettes from the drive, or to insert the first  
diskette created if it is desired to run the diagnostics.  
24 MT 0763 and 0764  
 
Checkout guide  
To run the test, do as follows:  
1. Insert the PC-Doctor disk into the diskette drive; then power on the computer.  
If the computer cannot be powered on, go to “Power system checkout” on page  
26, and check the power sources.  
If an error code appears, go to “Symptom-to-FRU index” on page 36.  
On the first screen, select the model and press Enter. Follow the instructions on  
the screen.  
2. The main panel of PC-Doctor appears.  
3. Select Diagnostics with the arrow keys, and press Enter.  
A pull-down menu appears. (Its exact form depends on the model.)  
Note: PC-Doctor menu does not mean the formal support device list. Some  
unsupported device names may appear in the PC-Doctor menu.  
Diagnostics  
Interactive Tests  
Hardware Info  
Utility  
Quit  
F1=Help  
Run Normal Test  
Run Quick Test  
CPU/Coprocessor  
Systemboard  
Video Adapter  
Fixed Disks  
Diskette Drives  
Memory Test - Full  
Memory Test - Quick  
PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved.  
Use the cursor keys and ESC to move in menus. Press ENTER to select.  
The options on the test menu are as follows:  
Diagnostics  
Interactive Tests  
v Run Normal Test  
v Run Quick Test  
v CPU/Coprocessor  
v Systemboard  
v Keyboard  
v Video  
v Mouse  
v System Load  
v Video Adapter  
v Fixed Disks  
v Diskette Drives  
v Memory Test – Full  
v Memory Test – Quick  
Notes:  
v In the Keyboard test in Interactive Tests, the Fn key should be held down with  
M key for at least 2 seconds; otherwise, it cannot be sensed.  
v Video Adapter test supports only the LCD display on the Lenovo 3000  
computer. If you have an external monitor attached to your computer, detach it  
before running PC-Doctor for DOS.  
4. Run the applicable function test.  
5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows  
messages describing it.  
6. To exit the test, select Quit — Exit Diag.  
To cancel the test, press Esc.  
Note: After running PC-Doctor, check the time and date on the system and reset  
them if they are incorrect.  
General descriptions 25  
Checkout guide  
Detecting system information with PC-Doctor  
PC-Doctor can detect the following system information:  
Hardware Info  
v System Configuration  
v Memory Contents  
v Physical Disk Drives  
v Logical Disk Drives  
v VGA Information  
v IDE Drive Info  
v PCI Information  
v PNPISA Info  
v SMBIOS Info  
v VESA LCD Info  
v Hardware Events Log  
Utility  
v Run External Tests  
v Surface Scan Hard Disk  
v Benchmark System  
v DOS Shell  
v Tech Support Form  
v Battery Rundown  
v View Test Log  
v Print Log  
v Save Log  
v Full Erase Hard Drive  
v Quick Erase Hard Drive  
PC-Doctor for Windows  
This product is designed to help you troubleshoot and resolve problems related to  
your computer. Select one of the categories listed below to display symptoms and  
solutions:  
v CHECK SYSTEM HEALTH  
v SYSTEM AND DEVICE TESTS  
v LENOVO TROUBLESHOOTING  
v CENTER  
v SYSTEM REPORTS  
v UPDATES AND SUPPORT  
Power system checkout  
To verify a symptom, do the following:  
1. Turn off the computer.  
2. Remove the battery pack.  
3. Connect the ac adapter.  
4. Check that power is supplied when you turn on the computer.  
5. Turn off the computer.  
6. Disconnect the ac adapter and install the charged battery pack.  
7. Check that the battery pack supplies power when you turn on the computer.  
If you suspect a power problem, see the appropriate one of the following power  
supply checkouts:  
26 MT 0763 and 0764  
 
Checkout guide  
Checking the ac adapter  
You are here because the computer fails only when the ac adapter is used.  
v If the power-on indicator does not turn on, check the power cord of the ac  
adapter for correct continuity and installation.  
v If the computer does not charge during operation, go to Checking operational  
charging.″  
To check the ac adapter, do the following:  
1. Unplug the ac adapter cable from the computer.  
2. Measure the output voltage at the plug of the ac adapter cable. See the  
following figure:  
Pin  
1
Voltage (V dc)  
+20  
3
2
2
0
3
Ground  
1
(20V)  
Note: Output voltage of pin no.2 of the ac adapter may be different from the  
one you are servicing.  
3. If the voltage is not correct, replace the ac adapter.  
4. If the voltage is acceptable, do the following:  
v Replace the system board.  
v If the problem persists, go to “Product overview” on page 30.  
Note: Noise from the ac adapter does not always indicate a defect.  
Checking operational charging  
To check whether the battery charges properly during operation, use a discharged  
battery pack or a battery pack that has less than 50% of the total power remaining  
when installed in the computer.  
Perform operational charging. If the battery status indicator or icon does not turn  
on, remove the battery pack and let it return to room temperature. Reinstall the  
battery pack. If the charge indicator or icon still does not turn on, replace the  
battery pack.  
If the charge indicator still does not turn on, replace the system board. Then  
reinstall the battery pack. If it is still not charged, go to the next section.  
Checking the battery pack  
Battery charging does not start until the Power Meter shows that less than 95% of  
the total power remains; under this condition the battery pack can charge to 100%  
of its capacity. This protects the battery pack from being overcharged or from  
having a shortened life.  
To check your battery, move your cursor to the Power Meter icon in the icon tray  
of the Windows taskbar and wait for a moment (but do not click), and the  
percentage of battery power remaining is displayed. To get detailed information  
about the battery, double-click the Power Meter icon.  
General descriptions 27  
 
Checkout guide  
Note: If the battery pack becomes hot, it may not be able to charge. Remove it  
from the computer and leave it at room temperature for a while. After it  
cools down, reinstall and recharge it.  
To check the battery pack, do the following:  
1. Power off the computer.  
2. Remove the battery pack and measure the voltage between battery terminals 1  
(−) and 7 (+). See the following figure:  
Terminal  
1, 2  
Voltage (V dc)  
Ground (−)  
7(+)  
6(+)  
5
4
3
6, 7  
+ 0 to + 12.6  
2(-)  
1(-)  
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.  
Note: Recharging will take at least 3 hours, even if the indicator does not turn  
on.  
If the voltage is still less than +11.0 V dc after recharging, replace the battery.  
4. If the voltage is more than +11.0 V dc, measure the resistance between battery  
terminals 4 and 7. The resistance must be 4 to 30 K .  
If the resistance is not correct, replace the battery pack. If the resistance is  
correct, replace the system board.  
28 MT 0763 and 0764  
Lenovo 3000 V100 and V200  
© Copyright Lenovo 2007  
29  
 
Product overview  
Product overview  
This section presents the following product-unique information:  
Specifications  
The following table lists the specifications of the Lenovo 3000 V100 and V200:  
Feature  
Description  
®
Processor  
v Intel CoreSolo processor T1300 (1.66 GHz), 2-MB L2  
cache (667 MHz)  
v Intel Core Duo processor T2050 (1.60 GHz), 2-MB L2  
cache (533 MHz)  
v Intel Core Duo processor T2250 (1.73 GHz), 2-MB L2  
cache (533 MHz)  
v Intel Core Duo processor T2300 (1.66 GHz), 2-MB L2  
cache (667 MHz)  
v Intel Core Duo processor T2300E (1.66 GHz), 2-MB L2  
cache (667 MHz)  
v Intel Core Duo processor T2350 (1.86 GHz), 2-MB L2  
cache (533 MHz)  
v Intel Core Duo processor T2400 (1.83 GHz), 2-MB L2  
cache (667 MHz)  
v Intel Core Duo processor T2500 (2.0 GHz), 2-MB L2 cache  
(667 MHz)  
v Intel Core 2 Duo processor T5200 (1.60 GHz), 2-MB L2  
cache (533 MHz)  
v Intel Core 2 Duo processor T5300 (1.73 GHz), 2-MB L2  
cache (533 MHz)  
v Intel Core 2 Duo processor T5600 (1.83 GHz), 2-MB L2  
cache (667 MHz)  
v Intel Core 2 Duo processor T7100 (1.83 GHz), 2-MB L2  
cache (800 MHz)  
v Intel Core 2 Duo processor T7200 (2.0 GHz), 4-MB L2  
cache (667 MHz)  
v Intel Core 2 Duo processor T7300 (2.0 GHz), 4-MB L2  
cache (800 MHz)  
v Intel Core 2 Duo processor T7500 (2.2 GHz), 4-MB L2  
cache (800 MHz)  
Bus architecture  
v 667-MHz PSB  
v 667-MHz DDR2 SDRAM (PC2-5300)  
v HUB link  
v PCI bus  
v LPC bus  
v PCI Express bus  
(continued)  
30 MT 0763 and 0764  
 
Product overview  
Feature  
Description  
Graphic memory chip  
v Intel 915GM/PM  
v Intel 945GM  
v Intel 965GM  
Display  
v 12.1-inch wide, 16M colors, WXGA (1280 768 resolution)  
TFT color LCD  
Standard memory  
v 256-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1  
v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1  
v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 2  
v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1  
v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 2  
v 2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1  
Optional memory  
v 256-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1  
v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1  
v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1  
v 2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1  
Maximum of 2.0 GB for MT 0763  
Maximum of 4.0 GB for MT 0764  
CMOS RAM  
v 242 bytes  
Hard disk drive  
v 40 GB, 5400 rpm, 9.5 mm high, SATA interface  
v 60 GB, 5400 rpm, 9.5 mm high, SATA interface  
v 80 GB, 5400 rpm, 9.5 mm high, SATA interface  
v 100 GB, 5400 rpm, 9.5 mm high, SATA interface  
v 120 GB, 5400 rpm, 9.5 mm high, SATA interface  
v 160 GB, 5400 rpm, 9.5 mm high, SATA interface  
Supported hard disk drives are depend on the model.  
Optical drive  
I/O port  
v DVD/CD-RW combo drive, 12.7 mm high  
v DVD-RAM/RW drive, 12.7 mm high  
v 5-1 Digital Media Reader  
v Fingerprint reader (some models)  
v External monitor connector  
v Stereo headphone jack  
v Monaural microphone jack  
v RJ11 connector  
v RJ45 connector  
v Universal serial bus (USB) connector × 3 (compatible with  
USB 1.1 and 2.0)  
v IEEE 1394 connector  
(continued)  
Lenovo 3000 V100 and V200 31  
Product overview  
Feature  
Description  
Internal modem  
Audio  
v 56.6 Kbps  
v Built-in stereo speakers  
v Software control volume  
Ethernet (on the system  
board)  
v 10/100 Ethernet  
Mini PCI adapter  
v Intel PRO Wireless 3945ABG Mini-PCI Express Adapter  
v Broadcom 802.11ag WLAN PCI-E Mini Card  
v Broadcom 802.11bg WLAN PCI-E Mini Card  
v ThinkPad® 11a/b/g/n Wireless LAN Mini-PCI Express  
Adapter  
v Intel Wireless WiFi Link 4965AGN  
ExpressCard slot  
v ExpressCard (34 module, 54 module)  
Bluetooth wireless (some  
models)  
v Bluetooth daughter card  
Modem  
v MDC-1.5, 56 kbps V.92 for MT 0763  
v AMoM, 56 kbps V.92 for MT 0764  
Touch pad  
Battery  
Yes  
v Li-ion battery (3 cells) 2.6 Ah  
v Li-ion battery (6 cells) 2.6 Ah  
AC adapter  
v 65-watt (20V) slim type  
Preinstalled operating  
system  
v Windows XP Professional  
v Windows XP Home Edition  
v Windows VistaHome Premium (32 bit)  
v Windows Vista Home Basic (32 bit)  
v Windows Vista Business (32 bit)  
v Windows Vista Ultimate (32 bit)  
32 MT 0763 and 0764  
Product overview  
Status indicators  
The system status indicators show the status of the computer, as follows:  
1
2
3
4
5
9
8
7
6
Indicator  
Meaning  
ꢀ1ꢁ  
ꢀ2ꢁ  
ꢀ3ꢁ  
Caps lock  
Caps Lock mode is enabled. You can enter all alphabetic  
characters (A-Z) in uppercase without pressing the Shift key. To  
enable or disable Caps Lock mode, press the CapsLk key.  
Num lock  
The numeric keypad on the keyboard is enabled. To enable or  
disable the keypad, press and hold the Fn key, and press the  
NmLk key.  
5-1 Digital  
Media Reader  
status  
A card in the 5-1 Digital Media Reader is being used to read and  
write data. When this indicator is blinking, do not put the  
computer into sleep (standby) mode, remove the card from the  
slot, or turn off the computer.  
ꢀ4ꢁ  
Device Access  
A hard disk drive or an optical drive is being used to read or  
write data. When this indicator is blinking, do not put the  
computer into sleep (standby) mode, remove the device from the  
bay, or turn off the computer.  
Note: Do not move the system while this indicator is on. Sudden  
physical shock could cause drive errors.  
ꢀ5ꢁ  
ꢀ6ꢁ  
Power on  
The computer is on and ready to use. This indicator stays lit  
whenever the computer is on and is not lit when the computer is  
in sleep (standby) mode.  
Sleep (standby) Green:  
status The computer is in sleep (standby) mode.  
Blinking green:  
The computer is entering sleep (standby) mode or hibernation  
mode, or is resuming normal operation.  
Lenovo 3000 V100 and V200 33  
 
Product overview  
Indicator  
Meaning  
Green:  
ꢀ7ꢁ  
Battery status  
The battery is charged between 80% to 100% of the capacity,  
and being discharged between 0% to 80% of the capacity.  
Blinking green:  
The battery is charged between 20% to 80% of the capacity,  
and being charged.  
Orange:  
The battery is charged between 5% and 20% of the capacity,  
and being discharged.  
Blinking orange (slow):  
The battery is charged between 5% to 20% of the capacity,  
and being charged.  
Blinking orange (rapid):  
The battery is charged between 0% to 5% of the capacity.  
ꢀ8ꢁ  
ꢀ9ꢁ  
Bluetooth status Green:  
R
Bluetooth wireless is operational, and the radio link is ready  
for use.  
Blinking green:  
Data is being transmitted.  
Wireless status  
Green:  
The wireless feature (the IEEE 802.11 standard or the IEEE  
802.11n) is on, and the radio link is ready for use.  
Blinking green:  
Data is being transmitted.  
FRU tests  
The following table shows the test for each FRU.  
FRU  
Applicable test  
System board  
1. Diagnostics --> CPU/Coprocessor  
2. Diagnostics --> Systemboard  
LCD unit  
Keyboard  
1. Diagnostics --> Video Adapter  
2. Interactive Tests --> Video  
1. Diagnostics --> Systemboard --> Keyboard  
2. Interactive Tests --> Keyboard  
Hard disk drive  
Diskette drive  
Memory  
Diagnostics --> Fixed Disks  
v Diagnostics --> Diskette Drives  
1. If two DIMMs are installed, remove one of them and run  
Diagnostics --> Memory Test—Quick.  
2. If the problem does not recur, return the DIMM to its place,  
remove the other one, and run the test again.  
3. If the test does not detect the error, run Diagnostics -->  
Memory Test—Full.  
34 MT 0763 and 0764  
 
Product overview  
Fn key combinations  
The following table shows the function of each combination of Fn with a function  
key.  
Key combination Description  
Fn+F1  
Fn+F2  
Fn+F3  
Fn+F4  
Volume down.  
Volume up.  
Reserved.  
Put the computer in sleep (standby) mode. To return to normal  
operation, press the Fn key only, without pressing a function key.  
Fn+F5  
Enable or disable the built-in wireless networking features and the  
Bluetooth features. If you press Fn+F5, a list of wireless features is  
displayed. You can quickly change the power state of each feature in  
the list.  
Fn+F6  
Fn+F7  
Reserved.  
Open the window for Choose Presentation or Display scheme. If you  
press this combination of keys, a list of schemes is displayed in the  
window. You can quickly select a scheme in the list.  
Fn+F8  
Reserved.  
Fn+F9  
Reserved.  
Fn+F10  
Fn+F11  
Fn+F12  
Make the computer display less bright.  
Make the computer display brighter.  
Put the computer into hibernation mode. To return to normal operation,  
press the power button.  
Fn+Esc  
Mute the sound from the computer.  
Scroll Lock (ScrLk).  
Fn+Insert  
Fn+Delete  
Fn+PrtSc  
Numeric Lock (NmLk)  
Has the same function as the SysRq key.  
Has the same function as the Break key.  
Has the same function as the Home key.  
Has the same function as the End key.  
Fn+Pause  
Fn+PgUp  
Fn+PgDn  
Fn+cursor keys  
These key combinations work with Windows Media Player. Fn+down  
arrow key works for the Play or Pause button, Fn+up arrow key for the  
Stop button, Fn+right arrow key for the Next Track button, and Fn+left  
arrow key for the Previous Track button.  
Lenovo 3000 V100 and V200 35  
 
Symptom-to-FRU index  
Symptom-to-FRU index  
The symptom-to-FRU index in this section lists symptoms and errors and their  
possible causes. The most likely cause is listed first, in boldface type.  
Note: Do the FRU replacement or other actions in the sequence shown in the  
column headed “FRU or action, in sequence.” If replacing a FRU does not  
solve the problem, put the original part back in the computer. Do not  
replace a nondefective FRU.  
This index can also help you determine, during regular servicing, what FRUs are  
likely to need to be replaced next.  
A numeric error is displayed for each error detected in POST or system operation.  
In the displays, n can be any number.  
If no numeric code is displayed, check the narrative descriptions of symptoms. If  
the symptom is not described there, go to “Intermittent problems” on page 41.  
Note  
For a device not supported by diagnostic codes in the Lenovo 3000 notebook  
computers, see the manual for that device.  
Numeric error codes  
Symptom or error  
FRU or action, in sequence  
0200  
1. Reseat the hard disk drive.  
2. Load Setup Defaults in BIOS Setup  
Utility.  
Failure Fixed Disk  
3. Hard disk drive.  
4. System board.  
021x  
1. Keyboard.  
Keyboard error  
2. System board.  
0220  
Load Setup Defaults in BIOS Setup Utility.  
Monitor type does not match CMOS—Run  
SETUP  
0230  
System board.  
Shadow RAM Failed at offset:nnnn  
0231  
1. DIMM.  
System RAM Failed at offset:nnnn  
2. System board.  
0232  
1. DIMM.  
Extended RAM Failed at offset:nnnn  
2. System board.  
0250  
1. Charge the backup battery for more  
than 8 hours by connecting the ac  
adapter.  
System battery is dead—Replace and run  
SETUP  
2. Replace the backup battery and run BIOS  
Setup Utility to reset the time and date.  
0251  
1. Charge the backup battery for more  
than 8 hours by connecting the ac  
adapter.  
System CMOS checksum bad—Default  
configuration use  
2. Replace the backup battery and run BIOS  
Setup Utility to reset the time and date.  
36 MT 0763 and 0764  
 
Symptom-to-FRU index  
Symptom or error  
FRU or action, in sequence  
0260  
1. Charge the backup battery for more  
than 8 hours by connecting the ac  
adapter.  
System timer error  
2. Replace the backup battery and run BIOS  
Setup Utility to reset the time and date.  
3. System board.  
0270  
1. Charge the backup battery for more  
than 8 hours by connecting the ac  
adapter.  
Real time clock error  
2. Replace the backup battery and run BIOS  
Setup Utility to reset the time and date.  
3. System board.  
0280  
1. Load “Setup Default” in BIOS Setup  
Previous boot incomplete— Default  
configuration used  
Utility.  
2. DIMM.  
3. System board.  
02F4  
1. Load Setup Defaults in BIOS Setup  
Utility.  
EISA CMOS not writable  
2. Replace the backup battery.  
3. System board.  
02F5  
1. DIMM.  
DMA test failed  
2. System board.  
02F6  
1. DIMM.  
Software NMI failed  
2. System board.  
02F7  
1. DIMM.  
Fail-safe timer NMI failed  
2. System board.  
Lenovo 3000 V100 and V200 37  
Symptom-to-FRU index  
Error messages  
Symptom or error  
FRU or action, in sequence  
Unsupported memory.  
DIMM. Make sure to use supported  
memory.  
Device address conflict.  
1. Load “Setup Defaults” in the BIOS  
Setup Utility.  
2. Backup battery.  
3. System board.  
Allocation error for device.  
1. Load “Setup Defaults” in the BIOS  
Setup Utility.  
2. Backup battery.  
3. System board.  
Failing bits: nnnn.  
1. DIMM.  
2. System board.  
Invalid system configuration data.  
I/O device IRQ conflict.  
1. DIMM.  
2. System board.  
1. Load “Setup Defaults” in the BIOS  
Setup Utility.  
2. Backup battery.  
3. System board.  
Hibernation error.  
1. Restore the system configuration to  
what it was before the computer  
entered hibernation mode.  
2. If memory size has been changed,  
re-create the hibernation file.  
Fan error.  
1. Fan.  
2. Thermal grease.  
3. System board.  
Thermal sensing error.  
System board.  
Authentication of system services failed.  
Press <Esc> to resume.  
The Predesktop Area in the HDD is  
corrupted. Restore it from a recovery disc.  
Cannot boot from any device.  
Check the status of device which you want  
to boot from.  
Device not found.  
1. The device you want to boot from.  
2. System board.  
Device Error.  
1. The device you want to boot from.  
2. System board.  
No valid operating system.  
1. Check that the operating system has no  
failure and is installed correctly.  
2. Reinstall the operation system.  
Excluded from boot order.  
v Enter the BIOS Setup Utility and add the  
device in boot order.  
38 MT 0763 and 0764  
 
Symptom-to-FRU index  
No-beep symptoms  
Symptom or error  
FRU or action, in sequence  
No beep, power-on indicator on, LCD blank, 1. Make sure that every connector is  
and no POST.  
connected tightly and correctly.  
2. DIMM.  
3. System board.  
No beep, power-on indicator on, and LCD  
blank during POST.  
1. Reseat DIMM.  
2. System board.  
The power-on password prompt appears.  
A power-on password or a supervisor  
password is set. Type the password and  
press Enter.  
The hard-disk password prompt appears.  
A hard-disk password is set. Type the  
password and press Enter.  
Lenovo 3000 V100 and V200 39  
 
Symptom-to-FRU index  
LCD-related symptoms  
Important  
The TFT LCD for the notebook computer contains many thin-film transistors  
(TFTs). The presence of a small number of dots that are missing, discolored,  
or always lighted is characteristic of TFT LCD technology, but excessive pixel  
problems can cause viewing concerns. The LCD should be replaced if the  
number of missing, discolored, or lighted dots in any background is:  
v WXGA: 8 or more bright dots, 8 or more dark dots, or a total of 9 or more  
bright and dark dots.  
Note: A bright dot means a pixel is always on (white or color.) A dark dot  
means a pixel is always off (black color.)  
Symptom or error  
FRU or action, in sequence  
No beep, power-on indicator on, and a  
blank LCD during POST.  
System board.  
v LCD backlight not working.  
v LCD too dark.  
1. Reseat the LCD connectors.  
2. LCD assembly.  
3. System board.  
v LCD brightness cannot be adjusted.  
v LCD contrast cannot be adjusted.  
v LCD screen unreadable.  
v Characters missing pixels.  
v Screen abnormal.  
1. See important note for “LCD-related  
symptoms.”  
2. Reseat all LCD connectors.  
3. LCD assembly.  
v Wrong color displayed.  
4. System board.  
Horizontal or vertical lines displayed on  
LCD.  
LCD assembly.  
40 MT 0763 and 0764  
 
Symptom-to-FRU index  
Intermittent problems  
Intermittent system hang problems can be due to a variety of causes that have  
nothing to do with a hardware defect, such as cosmic radiation, electrostatic  
discharge, or software errors. FRU replacement should be considered only when a  
problem recurs.  
When analyzing an intermittent problem, do the following:  
1. Run the diagnostic test for the system board in loop mode at least 10 times.  
2. If no error is detected, do not replace any FRUs.  
3. If any error is detected, replace the FRU shown by the FRU code. Rerun the  
test to verify that no more errors exist.  
Undetermined problems  
If the diagnostic tests did not identify the adapter or device that has failed, if  
wrong devices are installed, or if the system simply is not operating, follow these  
procedures to isolate the failing FRU (do not isolate FRUs that have no defects).  
Verify that all attached devices are supported by the computer.  
Verify that the power supply being used at the time of the failure is operating  
1. Turn off the computer.  
2. Visually check each FRU for damage. Replace any damaged FRU.  
3. Remove or disconnect all of the following devices:  
a. Non-Lenovo 3000 devices  
b. Devices attached to the port replicator  
c. Printer, mouse, and other external devices  
d. Battery pack  
e. Hard disk drive  
f. External diskette drive or optical drive  
g. DIMM  
h. Optical disk or diskette in the internal drive  
i. PC Cards  
4. Turn on the computer.  
5. Determine whether the problem has been solved.  
6. If the problem does not recur, reconnect the removed devices one at a time  
until you find the failing FRU.  
7. If the problem remains, replace the following FRUs one at a time (do not  
replace a nondefective FRU):  
a. System board  
b. LCD assembly  
Lenovo 3000 V100 and V200 41  
 
FRU replacement notices  
FRU replacement notices  
This section contains notices related to removing and replacing parts. Read this  
section carefully before replacing any FRU.  
Screw notices  
Loose screws can cause a reliability problem. In the Lenovo 3000 computer, this  
problem is addressed with special nylon-coated screws that have the following  
characteristics:  
v They maintain tight connections.  
v They do not easily come loose, even with shock or vibration.  
v They are harder to tighten.  
v Each one should be used only once.  
Do the following when you service this machine:  
v Keep the screw kit (for the P/N, see “Miscellaneous parts” on page 114) in your  
tool bag.  
v Always use new screws.  
v Use a torque screwdriver if you have one.  
Tighten screws as follows:  
v Plastic to plastic  
Turn an additional 90 degrees after the screw head touches the surface of the  
plastic part:  
90 degrees more  
(Cross-section)  
v Logic card to plastic  
Turn an additional 180 degrees after the screw head touches the surface of the  
logic card:  
180 degrees more  
(Cross-section)  
v Torque driver  
If you have a torque driver, refer to the “Torque” column for each step.  
v Make sure that you use the correct screw. If you have a torque screwdriver,  
tighten all screws firmly to the torque shown in the table. Never use a screw  
that you removed. Use a new one. Make sure that all of the screws are  
tightened firmly.  
v Ensure torque screwdrivers are calibrated correctly following country  
specifications.  
Retaining serial numbers  
This section includes the following descriptions:  
42 MT 0763 and 0764  
 
FRU replacement notices  
Restoring the serial number of the system unit  
When the computer was manufactured, the EEPROM on the system board was  
loaded with the serial numbers of the system and all major components. These  
numbers need to remain the same throughout the life of the computer.  
If you replace the system board, you must restore the serial number of the system  
unit to its original value.  
Before replacing the system board, save the original serial number by doing the  
following:  
1. Install the CE Utility Diskette for Lenovo 3000 notebooks, and restart the  
computer.  
2. From the main menu, select 1. Set System Identification.  
3. Select 2. Read S/N data from EEPROM.  
The serial number of each device in your computer is displayed; the serial number  
of the system unit is listed as follows:  
v 20: Serial number  
Write down that number.  
Note: The serial number of the system unit is also written on the label attached to  
the bottom of the computer.  
After you have replaced the system board, restore the serial number by doing the  
following:  
1. Install the CE Utility Diskette for Lenovo 3000 notebooks and restart the  
computer.  
2. From the main menu, select 1. Set System Identification.  
3. Select 1. Add S/N data from EEPROM.  
Follow the instructions on the screen.  
Retaining the UUID  
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to  
your computer at production and stored in the EEPROM of your system board.  
The algorithm that generates the number is designed to provide unique IDs until  
the year A.D. 3400. No two computers in the world have the same number.  
When you replace the system board, you must set the UUID on the new system  
board as follows:  
1. Install the CE Utility Diskette for Lenovo 3000 notebooks, and restart the  
computer.  
2. From the main menu, select 4. Assign UUID.  
A new UUID is created and written. If a valid UUID already exists, it is not  
overwritten.  
Reading or writing the ECA information  
Information on Engineering Change Announcements (ECA) are stored in the  
EEPROM of the system board. The electronic storage of this information simplifies  
the procedure to check if the ECA has been previously applied to a machine. The  
machine does not need to be disassembled to check for the ECA application.  
Lenovo 3000 V100 and V200 43  
 
FRU replacement notices  
To check what ECAs have been previously applied to the machine, use the ECA  
Information Read/Write function on the CE Utility Diskette for Lenovo 3000  
notebooks.  
1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the  
computer.  
2. From the main menu, select 6. Set ECA Information.  
3. To read ECA information, select 2. Read ECA/rework number from EEPROM  
and follow the instruction.  
4. To read box build date, select 5. Read box build date from EEPROM, and  
follow the instruction on the screen.  
After an ECA has been applied to the machine, the EEPROM must be updated to  
reflect the ECA's application. Use the CE Utility Diskette for Lenovo 3000  
notebooks to update the EEPROM.  
Note: Only the ECA number is stored in the EEPROM. The machine type of the  
ECA is assumed be the same as the machine type of the machine that had  
the ECA applied to it.  
1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the  
computer.  
2. From the main menu, select 6. Set ECA Information.  
3. To write ECA information, select 1. Write ECA/rework number from EEPROM,  
and follow the instruction.  
4. To write box build date, select 4. Write box build date from EEPROM, and  
follow the instruction on the screen.  
If the system board is being replaced, try to read the ECA information from the old  
system board and transfer the information to the new system. If the system board  
is inoperable, this will not be possible.  
44 MT 0763 and 0764  
Removing and replacing a FRU  
Removing and replacing a FRU  
This section presents directions and drawings for use in removing and replacing a  
FRU. Be sure to observe the following general rules:  
1. Do not try to service any computer unless you have been trained and certified.  
An untrained person runs the risk of damaging parts.  
2. Before replacing any FRU, review “FRU replacement notices” on page 42.  
3. Begin by removing any FRUs that have to be removed before the failing FRU.  
Any such FRUs are listed at the top of the page. Remove them in the order in  
which they are listed.  
4. Follow the correct sequence in the steps for removing the FRU, as given in the  
drawings by the numbers in square callouts.  
5. When turning a screw to replace a FRU, turn it in the direction as given by the  
arrow in the drawing.  
6. When removing the FRU, move it in the direction as given by the arrow in the  
drawing.  
7. To put the new FRU in place, reverse the removal procedure and follow any  
notes that pertain to replacement. For information about connecting and  
arranging internal cables, see “Locations” on page 86.  
8. When replacing a FRU, use the correct screw as shown in the procedures.  
DANGER  
Before removing any FRU, turn off the computer, unplug all power cords from  
electrical outlets, remove the battery pack, and then disconnect any interconnecting  
cables.  
Attention: After replacing a FRU, do not turn on the computer until you have  
made sure that all screws, springs, and other small parts are in place and none are  
loose inside the computer. Verify this by shaking the computer gently and listening  
for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.  
Attention: The system board is sensitive to, and can be damaged by, electrostatic  
discharge. Before touching it, establish personal grounding by touching a ground  
point with one hand or by using an electrostatic discharge (ESD) strap (P/N  
6405959).  
Lenovo 3000 V100 and V200 45  
 
Removing and replacing a FRU  
1010 Battery pack  
DANGER  
Use only the battery specified in the parts list for your computer. Any other battery  
could ignite or explode.  
Unlock the battery release lever ꢀ1ꢁ and holding the battery release lever in the  
unlocked position ꢀ2ꢁ, remove the battery pack in the direction shown by arrow  
ꢀ3ꢁ.  
2
1
3
46 MT 0763 and 0764  
 
Removing and replacing a FRU  
1020 Hard disk drive slot cover and hard disk drive  
For access, remove this FRU:  
Attention  
v Do not drop the hard disk drive or apply any physical shock to it. The  
hard disk drive is sensitive to physical shock. Improper handling can cause  
damage and permanent loss of data.  
v Before removing the drive, have the user make a backup copy of all the  
information on it if possible.  
v Never remove the drive while the system is operating or is in suspend  
mode.  
Note: Loosen the screws ꢀ1ꢁ, but do not remove them.  
2
1
(continued)  
Lenovo 3000 V100 and V200 47  
 
Removing and replacing a FRU  
4
3
5
When installing: Make sure that the hard disk drive connector is attached firmly.  
48 MT 0763 and 0764  
Removing and replacing a FRU  
1030 DIMM slot cover  
For access, remove this FRU:  
Note: Loosen the screws ꢀ1ꢁ, but do not remove them.  
2
1
1040 DIMM  
For access, remove these FRUs in order:  
1
2
1
When installing: Insert the notched end of the DIMM into the socket. Press the  
DIMM firmly, and pivot it until it snaps into the place. Make  
sure that it is firmly fixed in the slot and does not move easily.  
Lenovo 3000 V100 and V200 49  
 
Removing and replacing a FRU  
1050 Backup battery  
DANGER  
Use only the battery specified in the parts list for your computer. Any other battery  
could ignite or explode.  
For access, remove these FRUs in order:  
1
2
When installing: Make sure that the battery connector is attached firmly.  
50 MT 0763 and 0764  
 
Removing and replacing a FRU  
1060 PCI Express Mini Card slot cover and PCI Express Mini  
Card for 802.11 a/b/g wireless LAN  
For access, remove these FRUs in order:  
Note: Loosen the screws ꢀ1ꢁ, but do not remove them.  
2
1
4
4
3
3
5
In step ꢀ3ꢁ, unplug the jacks by using the removal tool antenna RF connector  
(P/N: 08K7159) or pick the connectors with your fingers and gently unplug them  
in direction of the arrow.  
Step  
Screw (quantity)  
Color  
Torque  
ꢀ4ꢁ  
M2 × 4 mm, pan-head, nylon-coated (2)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Plug the gray cable into the jack labeled MAIN on the card, and  
the black cable into the jack labeled AUX.  
Lenovo 3000 V100 and V200 51  
 
Removing and replacing a FRU  
1070 PCI Express Mini Card slot cover and PCI Express Mini  
Card 802.11 a/b/g/n wireless LAN  
For access, remove these FRUs in order:  
Note: Loosen the screws ꢀ1ꢁ, but do not remove them.  
2
1
(continued)  
52 MT 0763 and 0764  
 
Removing and replacing a FRU  
For MT 0763  
4
4
3
3
5
In step ꢀ3ꢁ, unplug the jacks by using the removal tool antenna RF connector  
(P/N: 08K7159) or pick the connectors with your fingers and gently unplug them  
in direction of the arrow.  
Step  
Screw (quantity)  
Color  
Torque  
ꢀ4ꢁ  
M2 × 4 mm, pan-head, nylon-coated (2)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Plug the gray cable into the jack labeled TR1 on the card, and  
the black cable into the jack labeled TR2.  
(continued)  
Lenovo 3000 V100 and V200 53  
Removing and replacing a FRU  
For MT 0764  
4
4
3
5
In step ꢀ3ꢁ, unplug the jacks by using the removal tool antenna RF connector  
(P/N: 08K7159) or pick the connectors with your fingers and gently unplug them  
in direction of the arrow.  
Step  
Screw (quantity)  
Color  
Torque  
ꢀ4ꢁ  
M2 × 4 mm, pan-head, nylon-coated (2)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Plug the gray cable (MAIN) into the jack labeled 1, the black  
cable (AUX) into the jack labeled 2, and the white cable (MIMO)  
into the jack labeled 3 on the card.  
54 MT 0763 and 0764  
Removing and replacing a FRU  
1080 Optical drive  
For access, remove this FRU:  
1
3
2
Step  
Screw (quantity)  
M2.5 × 5 mm, pan-head, nylon-coated (1)  
Color  
Torque  
ꢀ1ꢁ  
Silver  
0.392 Nm  
(4 kgfcm)  
1090 Middle cover  
For access, remove this FRU:  
4
4
4
4
1
3
2
Lenovo 3000 V100 and V200 55  
 
Removing and replacing a FRU  
1100 Function board  
For access, remove these FRUs in order:  
3
1
1
2
Step  
Screw (quantity)  
M2 × 4 mm, pan-head, nylon-coated (2)  
Color  
Torque  
ꢀ1ꢁ  
Silver  
0.245 Nm  
(2.5 kgfcm)  
56 MT 0763 and 0764  
 
Removing and replacing a FRU  
1110 Keyboard  
For access, remove these FRUs in order:  
1
Step  
Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2.5 × 7 mm, pan-head, nylon-coated (1)  
Black  
0.392 Nm  
(4 kgfcm)  
(continued)  
Lenovo 3000 V100 and V200 57  
 
Removing and replacing a FRU  
2
3
4
3
Lift the keyboard a little in the direction shown by arrow ꢀ2ꢁ. Then unlock the  
connector ꢀ3ꢁ and detach the connector ꢀ4ꢁ.  
When installing:  
1. Make sure that the keyboard connector is attached firmly. Then lock the  
connector.  
2. Make sure that the front side of the keyboard is under the frame.  
58 MT 0763 and 0764  
Removing and replacing a FRU  
1120 Hinge covers, keyboard bezel, 5-1 Digital Media Reader  
card, BDC, and fingerprint reader card  
For access, remove these FRUs in order:  
Note: 5-1 Digital Media Reader card, BDC, and fingerprint reader card are  
attached underside of the keyboard bezel.  
1
2
2
2
2
1
2
2
Step  
Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2.5 × 13 mm, pan-head, nylon-coated (2)  
Silver  
0.392 Nm  
(4 kgfcm)  
ꢀ2ꢁ  
M2.5 × 5 mm, pan-head, nylon-coated (7)  
Silver  
0.392 Nm  
(4 kgfcm)  
(continued)  
Lenovo 3000 V100 and V200 59  
 
Removing and replacing a FRU  
Remove the hinge cap L ꢀ3aꢁ and the hinge cap R ꢀ3bꢁ.  
3b  
3a  
Note: Steps ꢀ4ꢁ and ꢀ5ꢁ are only for MT 0763.  
4
5
5
5
(continued)  
60 MT 0763 and 0764  
Removing and replacing a FRU  
Release the antenna cables from the cable guides of the frame. In step ꢀ6ꢁ, take  
care not to damage the cables when you pull out them from the guide hole.  
7
7
7
6
When installing: Route the antenna cables along the cable guides. When you route  
the cables, do not tense them. To do so, the cables may get  
damaged by the cable guides of the frame, and may cause a  
broken wire.  
(continued)  
Lenovo 3000 V100 and V200 61  
Removing and replacing a FRU  
8
8
8
8
8
When installing: Make sure that all the connectors are attached firmly.  
9
9
9
Step  
Screw (quantity)  
Color  
Torque  
ꢀ9ꢁ  
M2.5 × 5 mm, pan-head, nylon-coated (3)  
Silver  
0.392 Nm  
(4 kgfcm)  
(continued)  
62 MT 0763 and 0764  
Removing and replacing a FRU  
10  
11  
Lenovo 3000 V100 and V200 63  
Removing and replacing a FRU  
To remove the 5-1 Digital Media Reader card, do as follows:  
1
1
2
a
Step  
Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2 × 2.5 mm, pan-head, nylon-coated (2)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
3
4
3
When installing: Make sure that all the connectors are attached firmly.  
64 MT 0763 and 0764  
Removing and replacing a FRU  
To remove the BDC, do as follows:  
2
1
1
3
Step  
Screw (quantity)  
M2 × 2.5 mm, pan-head, nylon-coated (2)  
Color  
Torque  
ꢀ1ꢁ  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Make sure that the connector is attached firmly.  
Lenovo 3000 V100 and V200 65  
Removing and replacing a FRU  
To remove the fingerprint reader card, do as follows:  
1
1
1
2
3
3
3
Step  
Screw (quantity)  
M2 × 2.5 mm, pan-head, nylon-coated (3)  
Color  
Torque  
ꢀ1ꢁ  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Make sure that the connector is attached firmly.  
66 MT 0763 and 0764  
Removing and replacing a FRU  
1130 LCD unit  
For access, remove these FRUs in order:  
1
1
2
2
Step  
Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2.5 × 5 mm, pan-head, nylon-coated (2)  
Silver  
0.392 Nm  
(4 kgfcm)  
ꢀ2ꢁ  
M2.5 × 5 mm, pan-head, nylon-coated (2)  
Silver  
0.392 Nm  
(4 kgfcm)  
(continued)  
Lenovo 3000 V100 and V200 67  
 
Removing and replacing a FRU  
5
3
4
4
3
Step  
Screw (quantity)  
Color  
Torque  
ꢀ3ꢁ  
M2.5 × 5 mm, pan-head, nylon-coated (2)  
Silver  
0.392 Nm  
(4 kgfcm)  
ꢀ4ꢁ  
M2 × 4 mm, pan-head, nylon-coated (2)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Make sure that the LCD connector ꢀ5ꢁ is attached firmly.  
(continued)  
68 MT 0763 and 0764  
Removing and replacing a FRU  
6
6
When installing: When you attach the LCD unit, make sure that you do not pinch  
the antenna cable.  
Lenovo 3000 V100 and V200 69  
Removing and replacing a FRU  
1140 Heat sink assembly, CPU, MDC, ExpressCard slot, and  
system board  
For access, remove these FRUs, in order:  
Note: Heat sink assembly, CPU, MDC, and ExpressCard slot are attached to the  
system board.  
1
3
2
Step  
Screw (quantity)  
Color  
Torque  
ꢀ3ꢁ  
M2.5 × 5 mm, pan-head, nylon-coated (1)  
Silver  
0.392 Nm  
(4 kgfcm)  
When installing: Make sure that the connectors are firmly attached.  
70 MT 0763 and 0764  
 
Removing and replacing a FRU  
5
4
Remove the heat sink as follows:  
2
3
1
2
2
Step  
Screw (quantity)  
M2 × 2.5 mm, pan-head, nylon-coated (1)  
Color  
Torque  
ꢀ1ꢁ  
Silver  
0.245 Nm  
(2.5 kgfcm)  
Note: Loosen the screws ꢀ2ꢁ, but do not remove them.  
(continued)  
Lenovo 3000 V100 and V200 71  
Removing and replacing a FRU  
When installing: Before you attach a new thermal module to the computer, peel  
off the covering film of thermal grease. Then attach the thermal  
module to the computer.  
For MT 0763  
a
For MT 0764  
a
(continued)  
72 MT 0763 and 0764  
Removing and replacing a FRU  
Remove the CPU as follows:  
Attention: CPU is extremely sensitive. When you service the CPU, avoid any  
kind of rough handling.  
Rotate the head of the screw in the direction shown by arrow ꢀ1ꢁ to release the  
lock; then remove the CPU in the direction shown by arrow ꢀ2ꢁ.  
1
a
b
2
When installing: Place the CPU on the CPU socket ꢀaꢁ, and then rotate the head  
of the screw in the direction shown by arrow ꢀbꢁ to secure the  
CPU.  
(continued)  
Lenovo 3000 V100 and V200 73  
Removing and replacing a FRU  
Remove the MDC as follows:  
For MT 0763  
1
1
2
Step  
Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2 × 2.5 mm, pan-head, nylon-coated (2)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
3
4
When installing: Make sure that the connector on the underside of the card is  
attached to the system board firmly, and then fasten the screws.  
(continued)  
74 MT 0763 and 0764  
Removing and replacing a FRU  
For MT 0764  
1
1
3
2
Step  
Screw (quantity)  
M2 × 2.5 mm, pan-head, nylon-coated (2)  
Color  
Torque  
ꢀ1ꢁ  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Make sure that the connector on the underside of the card is  
attached to the system board firmly, and then fasten the screws.  
(continued)  
Lenovo 3000 V100 and V200 75  
Removing and replacing a FRU  
Remove the ExpressCard slot as follows:  
1
1
1
1
Step  
Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2 × 2.5 mm, pan-head, nylon-coated (4)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
Turn over the system board, and disconnect the ExpressCard slot assembly.  
2
When installing: Make sure that the connector is attached firmly, and then fasten  
the screws.  
76 MT 0763 and 0764  
Removing and replacing a FRU  
Note: Applying labels to the bottom cover  
When you replace the base cover, you need to stick some labels on the new  
base cover. Some of the labels have been shipped with the new base cover,  
and some may need to be reused from the old base cover.  
Following labels are the typical labels stuck on the bottom side of the  
computer when it is shipped.  
ꢀaꢁ Windows license label (COA)  
ꢀbꢁ MAC label (802.11 a/b/g)  
ꢀcꢁ MAC label (802.3)  
ꢀdꢁ Homologation label  
ꢀeꢁ Product label  
ꢀfꢁ Serial number label  
b
c
d
f
e
For some models, you also need to apply one or two FCC labels or the other  
types of labels. Check the old base cover; if it has one or two FCC labels or  
the other types of labels, find duplicates of them in the package and apply  
them to the new base cover.  
78 MT 0763 and 0764  
Removing and replacing a FRU  
2010 LCD front bezel  
For access, remove this FRU:  
1
1
1
1
Step  
Screw cap Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2.5 × 5 mm, pan-head,  
nylon-coated (4)  
Black  
0.392 Nm  
(4 kgfcm)  
2
Lenovo 3000 V100 and V200 79  
 
Removing and replacing a FRU  
2020 Inverter card  
For access, remove these FRUs in order:  
1
2
1
4
3
Step  
Screw (quantity)  
M2 × 4 mm, pan-head, nylon-coated (2)  
Color  
Torque  
ꢀ1ꢁ  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Make sure that connectors ꢀ3ꢁ and ꢀ4ꢁ are attached firmly.  
Cable routing: Route the cables as shown in the following figure.  
80 MT 0763 and 0764  
 
Removing and replacing a FRU  
2030 Integrated camera  
For access, remove these FRUs in order:  
Note: The part marked ꢀaꢁ is fragile and might be damaged by rough handling.  
When you remove the camera, do not hold that part to avoid the damage.  
a
1
1
2
3
Step  
Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2 × 4 mm, pan-head, nylon-coated (2)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
When installing: Make sure that connectors ꢀ2ꢁ is attached firmly.  
Lenovo 3000 V100 and V200 81  
 
Removing and replacing a FRU  
2040 LCD panel, LCD cable, and hinges  
For access, remove these FRUs in order:  
1
1
1
1
Step  
Screw (quantity)  
Color  
Torque  
ꢀ1ꢁ  
M2.5 × 5 mm, pan-head, nylon-coated (6)  
Black  
0.392 Nm  
(4 kgfcm)  
Release the antenna cables from the cable guides.  
2
2
(continued)  
82 MT 0763 and 0764  
 
Removing and replacing a FRU  
5
4
3
When installing: Make sure that the camera connector is attached firmly.  
Remove the hinges from the LCD panel.  
6
6
7
6
7
6
Step  
Screw (quantity)  
Color  
Torque  
ꢀ6ꢁ  
M2 × 3 mm, pan-head, nylon-coated (4)  
Silver  
0.245 Nm  
(2.5 kgfcm)  
Remove the LCD cable assembly from the LCD panel.  
8
Lenovo 3000 V100 and V200 83  
Removing and replacing a FRU  
2050 Wireless LAN antenna cables  
For access, remove these FRUs in order:  
For the antennas with two cables  
2
4
1
2
2
3
1
Step  
Screw (quantity)  
M2 × 4 mm, pan-head, nylon-coated (3)  
Color  
Torque  
ꢀ2ꢁ  
Silver  
0.245 Nm  
(2.5 kgfcm)  
Cable routing: Route the cables as shown in the following figure.  
(continued)  
84 MT 0763 and 0764  
 
Removing and replacing a FRU  
For the antennas with three cables  
2
4
1
2
2
2
3
1
Step  
Screw (quantity)  
M2 × 4 mm, pan-head, nylon-coated (4)  
Color  
Torque  
ꢀ2ꢁ  
Silver  
0.245 Nm  
(2.5 kgfcm)  
Cable routing: Route the cables as shown in the following figure.  
Lenovo 3000 V100 and V200 85  
Locations  
Locations  
Front view  
ꢀ1ꢁ  
ꢀ2ꢁ  
ꢀ3ꢁ  
ꢀ4ꢁ  
ꢀ5ꢁ  
ꢀ6ꢁ  
ꢀ7ꢁ  
ꢀ8ꢁ  
ꢀ9ꢁ  
ꢀ10ꢁ  
Integrated camera (for some models)  
Power switch  
Lenovo Care button  
Instant on button  
Volume control buttons  
Keyboard  
Fingerprint reader (for some models)  
Touch pad  
Touch pad buttons  
System and power status indicators  
Note: For the description of each indicator, see “Status indicators” on page  
ꢀ11ꢁ  
ꢀ12ꢁ  
ꢀ13ꢁ  
ꢀ14ꢁ  
ꢀ15ꢁ  
ꢀ16ꢁ  
ꢀ17ꢁ  
ꢀ18ꢁ  
ExpressCard slot  
IEEE1394 connector  
Stereo headphone jack  
Microphone jack  
External monitor connector  
Universal serial bus (USB) connector  
Security keyhole  
System and power status indicators  
Note: For the description of each indicator, see “Status indicators” on page  
1
2
3
4
5
6
7
18  
8
17  
9
16  
15  
14  
10  
13  
12  
11  
86 MT 0763 and 0764  
 
Locations  
Rear view  
ꢀ1ꢁ  
ꢀ2ꢁ  
ꢀ3ꢁ  
ꢀ4ꢁ  
ꢀ5ꢁ  
ꢀ6ꢁ  
ꢀ7ꢁ  
ꢀ8ꢁ  
USB connector  
AC power connector  
USB connector  
RJ-45 (Ethernet) connector  
RJ-11 (modem) connector  
Optical drive  
Wireless radio switch  
5-1 Digital Media Reader  
8
7
6
5
4
1
3
2
Bottom view  
ꢀ1ꢁ  
ꢀ2ꢁ  
ꢀ3ꢁ  
ꢀ4ꢁ  
ꢀ5ꢁ  
ꢀ6ꢁ  
ꢀ7ꢁ  
Battery pack latch  
Battery pack  
PCI Express Mini card slot  
Memory card slot  
Battery pack latch  
Hard disk drive slot  
System and power status indicators  
Note: For the description of each indicator, see “Status indicators” on page  
ꢀ8ꢁ  
Built-in stereo speakers  
5
4
6
3
2
1
7
8
Lenovo 3000 V100 and V200 87  
 
Parts list  
Parts list  
v Each FRU is available for all types or models, unless specific types or models are  
specified.  
v FRU with specific models listed and described as xxU (where U is an example of  
a country designator) should be used for all models ending in U.  
v FRU with specific models listed and described as 3Dx (where 3D is an example  
of a unique configuration) should be used for all of these models, unless specific  
country or region designator is specified.  
v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two  
asterisks (**) in the CRU ID column. An N in the CRU ID column means the  
part is not a CRU. A single asterisk (*) means the part is an External CRU; two  
asterisks (**) means the part is an Internal CRU.  
Lenovo 3000 computers contain the following types of the external CRUs:  
External CRUs (pluggable)  
These CRUs unplug from the computer. Examples of these types of  
CRUs include an ac adapter, an external keyboard, a mouse, a power  
cord, a port replicator, a USB device, and an external bay device adapter.  
External CRUs with latches  
These CRUs have a latch to help you to remove and replace the part.  
Examples of these types of CRUs include a battery pack, a cover such as  
a memory card slot cover and a hard disk drive slot cover.  
Lenovo 3000 computers contain the following types of the internal CRUs:  
Internal CRUs (located behind an access panel)  
These CRUs are isolated parts within the computer that are concealed by  
an access panel that is typically secured by either one or two screws.  
Once the access panel is removed, only the specific CRU is visible.  
Examples of these types of CRUs include a memory card and a hard  
disk drive.  
Internal CRUs (located within the product itself)  
These CRUs are accessible only by opening the outer case of the  
computer. Examples of these CRUs include the parts beneath a cover  
and they are secured by either one or two screws.  
v A RoHS compliant FRU is identified by an R. An N in the RoHS ID column  
means the part is not a RoHS compliant FRU.  
v FRUs marked with ꢀOPꢁ are available as options.  
88 MT 0763 and 0764  
 
Parts list  
Overall  
1
2
3
4
5
6
a
7
8
25  
b
c
9
24  
23  
22  
10  
11  
12  
13  
21  
20  
14  
15  
19  
18  
16  
17  
Lenovo 3000 V100 and V200 89  
 
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
1
2
3
4
5
Hinge caps  
41W6375  
41W6374  
R
R
N
N
Middle cover  
Launch board for MT 0763  
Launch board for MT 0764  
41W1333  
41R7645  
41W6371  
R
R
R
N
N
N
6
Keyboard bezel assembly without a fingerprint reader  
for MT 0763  
v 0763-33x, 59x, 65x, 69x, 82x, 83x, 97x, 99x, A3x, A5x,  
B3x, B7x, C3x, C5x, C6x, C7x, C8x, D5x, D9x, E2x,  
E6x, E7x, E9x, F3x, G3x, G7x, J5, J7x, 2Gx, 2Px, 3Ax,  
3Ex, 4Bx, 6Ax, 6Ex, 2Xx, 5Kx  
Keyboard bezel assembly without a fingerprint reader  
for MT 0764  
v 0764-22x  
41R5801  
41W6372  
R
R
N
N
Keyboard bezel assembly with a fingerprint reader for  
MT 0763  
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 34x, 36x, 38x, 43x,  
44x, 46x, 49x, 62x, 64x, 66x, 68x, 77x, 84x, 85x, 86x,  
88x, 89x, 93x, A2x, A4x, A6x, A8x, C2x, C4x, C9x, E3x,  
E4x, E5x, E8x, G2x, G9x, J3x, J8x, J9x, 2Cx, 2Dx, 2Ex,  
2Fx, 2Hx, 2Qx, 2Rx, 2Sx, 3Cx, 3Dx, 3Fx, 3Gx, 3Hx,  
4Ax, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx,  
5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Cx, 6Bx, 6Dx, 6Fx, 6Hx,  
7Ax, 7Bx, 7Cx,7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 8Bx, 8Cx, 8Dx,  
8Ex, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 3Lx, 3Mx, 3Nx, 4Jx,  
4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx,  
5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Xx,  
5Yx, 5Zx, 6Jx, 6Kx  
Keyboard bezel assembly with a fingerprint reader for  
MT 0764  
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,  
2Dx, 2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x, 48x,  
49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,  
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Zx  
41R5802  
41W1332  
R
R
N
N
7
5-1 Digital Media Reader board  
(continued)  
90 MT 0763 and 0764  
Parts list  
No. FRU  
8 Bluetooth daughter card (BDC)  
FRU no.  
RoHS CRU  
ID  
ID  
41W1163  
R
N
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 34x, 36x, 38x, 43x,  
44x, 46x, 49x, 62x, 64x, 66x, 68x, 69x, 82x, 83x, 84x,  
86x, 88x, 89x, 99x, A2x, A3x, A4x, A5x, A6x, A8x, B3x,  
C2x, C4x, C6x, C7x, C8x, C9x, E2x, E3x, E4x, E5x, E6x,  
E8x, G2x, J8x, J9x, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px,  
2Qx, 2Rx, 2Sx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 4Ax,  
4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx, 5Dx,  
5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Fx,  
6Hx, 7Ax, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 8Bx,  
8Cx, 8Dx, 8Ex, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 3Lx, 3Mx,  
3Nx, 4Jx, 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx,  
4Zx, 5Kx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux,  
5Wx, 5Xx, 5Yx, 5Zx, 6Jx, 6Kx  
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,  
2Dx, 2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x, 48x,  
49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Hx, 4Jx, 4Lx, 4Mx,  
4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Zx  
9
Fingerprint reader card for MT 0763  
41W1334  
R
N
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 34x, 36x, 38x, 43x,  
44x, 46x, 49x, 62x, 64x, 66x, 68x, 77x, 84x, 85x, 86x,  
88x, 89x, 93x, A2x, A4x, A6x, A8x, C2x, C4x, C9x, E3x,  
E4x, E5x, E8x, G2x, G9x, J3x, J8x, J9x, 2Cx, 2Dx, 2Ex,  
2Fx, 2Hx, 2Qx, 2Rx, 2Sx, 3Cx, 3Dx, 3Fx, 3Gx, 3Hx,  
4Ax, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx,  
5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Cx, 6Bx, 6Dx, 6Fx, 6Hx,  
7Ax, 7Bx, 7Cx,7Dx, 7Ex, 7Fx,7Gx, 8Ax, 8Bx, 8Cx, 8Dx,  
8Ex, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 3Lx, 3Mx, 3Nx, 4Jx,  
4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx,  
5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Xx,  
5Yx, 5Zx, 6Jx, 6Kx  
Fingerprint reader card for MT 0764  
41R5805  
41W1321  
R
R
N
N
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,  
2Dx, 2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x, 48x,  
49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,  
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Zx  
10 System board assembly, 12W integrated  
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 33x, 34x, 36x, 38x,  
43x, 44x, 46x, 49x, 59x, 62x, 64x, 65x, 66x, 68x, 69x,  
77x, 82x, 83x, 84x, 85x, 86x, 88x, 89x, 93x, 97x, 99x,  
A2x, A3x, A4x, A5x, A6x, A8x, B3x, B7x, C2x, C3x,  
C4x, C5x, C6x, C7x, C8x, C9x, D5x, D9x, E2x, E3x,  
E4x, E5x, E6x, E7x, E8x, E9x, F3x, G2x, G3x, G7x, G9x,  
J3x, J5x, J7x, J8x, J9x  
System board assembly, 12W integrated  
41W1423  
R
N
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx,  
3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 4Ax, 4Bx, 4Cx,  
4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex,  
5Fx, 5Gx, 5Hx, 5Jx, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx,  
7Ax, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 8Bx, 8Cx,  
8Dx, 8Ex  
(continued)  
Lenovo 3000 V100 and V200 91  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
10 System board assembly, 12W integrated  
v 0763- 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 2Xx, 3Lx, 3Mx, 3Nx,  
4Jx, 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx,  
5Kx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx,  
5Xx, 5Yx, 5Zx, 6Jx, 6Kx  
42W7671  
R
N
System board assembly, 12W integrated  
41R5796  
R
N
v 0764-22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx,  
2Cx, 2Dx, 2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x,  
48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx,  
4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Zx  
11 Modem daughter card (MDC) for MT 0763  
Modem daughter card (MDC) for MT 0764  
41W1324  
41R5798  
R
R
N
N
12 DVD/CD-RW combo drive assembly, 12.7 mm for MT 0763  
v 0763-23x, 33x, 34x, 36x, 38x, 59x, 77x, 82x, 83x, 97x, A5x, B7x, C5x, C6x, C7x, C8x,  
D5x, D9x, E3x, E4x, E5x, E6x, E7x, E9x, F3x, G3x, G7x, G9x, J3x, 3Ax, 3Ex, 3Fx, 5Jx,  
6Bx, 7Ax, 7Bx, 8Ax, 8Bx, 8Dx, 8Ex, 5Xx, 5Yx  
HLDS  
27R2364  
27R2370  
R
R
**  
**  
Panasonic  
DVD/CD-RW combo drive assembly, 12.7 mm for MT 0764  
v 0764-22x, 44x, 45x, 46x, 4Lx, 4Mx, 4Px, 4Qx, 4Rx  
HLDS  
42T2016  
42T2039  
R
R
**  
**  
Panasonic  
DVD-RAM/RW drive assembly, 12.7 mm for MT 0763  
v 0763-22x, 25x, 26x, 27x, 29x, 43x, 44x, 46x, 49x, 62x, 64x, 65x, 66x, 68x, 69x, 84x,  
85x, 86x, 88x, 89x, 93x, 99x, A2x, A3x, A4x, A6x, A8x, B3x, C2x, C3x, C4x, C9x,  
E2x, E8x, G2x, J5x, J7x, J8x, J9x, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx, 2Sx,  
3Cx, 3Dx, 3Gx, 3Hx, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx, 5Dx,  
5Ex, 5Fx, 5Gx,5Hx, 6Ax, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 8Cx,  
2Lx, 2Mx, 2Ux, 2Vx, 2Wx 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx,  
4Xx, 4Yx, 4Zx, 5Kx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Zx, 6Jx, 6Kx  
HLDS  
27R2368  
27R2372  
R
R
**  
**  
Panasonic  
DVD-RAM/RW drive assembly, 12.7 mm for MT 0764  
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Lx, 2Mx, 32x, 42x, 43x,  
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Nx, 4Tx, 4Ux,  
4Zx  
HLDS  
42T2021  
42T2011  
41W6373  
41R5803  
R
R
R
R
**  
**  
N
N
Panasonic  
13 Base cover assembly for MT 0763  
Base cover assembly for MT 0764  
(continued)  
92 MT 0763 and 0764  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
14 Intel PRO Wireless 3945ABG Mini-PCI Express Adapter  
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 36x, 38x, 43x, 44x, 46x, 49x, 62x, 64x, 66x, 68x,  
69x, 82x, 83x, 84x, 86x, 88x, 89x, 97x, 99x, A2x, A3x, A4x, A5x, A6x, A8x, B3x, B7x,  
C2x, C3x, C4x, C6x, C7x, C8x, C9x, E2x, E3x, E4x, E5x, E8x, G2x, G3x, G7x, J5x,  
J7x, 2Px, 2Qx, 2Rx, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 4Ax, 4Bx, 4Dx, 4Ex, 4Fx,  
4Gx, 5Ax, 5Bx, 5Cx, 5Ex, 5Gx, 5Hx, 5Jx, 6Ax, 6Bx, 6Dx, 7Ax, 7Bx, 7Cx, 7Ex, 8Ax,  
8Bx, 8Cx, 8Dx, 8Ex, 2Lx, 2Mx, 2Ux, 2Wx, 2Xx, 3Lx, 3Mx, 4Rx, 4Sx, 5Wx, 5Xx, 5Yx,  
5Zx, 6Kx  
v 0764-27x, 2Bx, 2Cx, 2Lx, 45x, 46x, 4Hx, 4Mx, 4Nx, 4Qx, 4Rx,  
xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxQ, xxS, xxU,  
xxV, xxY  
42T0853  
R
**  
xxK  
42T0857  
42T0859  
42T0861  
R
R
R
**  
**  
**  
xxE, xxJ  
xxG, xxR, xxT (802.11 b/g)  
Broadcom 802.11ag WLAN PCI-E Mini Card  
v 0763-33x, 34x, 59x, 65x, 77x, 85x, 93x, C5x, D5x, D9x, E6x, E7x, E9x, F3x, G9x, J3x,  
J8x, J9x, 4Jx, 4Nx, 5Px  
xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxQ, xxS, xxU,  
xxV, xxY  
41W1297  
R
**  
xxG  
41W1299  
41W1301  
41W1303  
R
R
R
**  
**  
**  
xxK  
xxE, xxJ  
Broadcom 802.11bg WLAN PCI-E Mini Card  
v 0763-5Kx  
v 0764-22x, 26x, 2Mx, 44x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Lx, 4Px, 4Tx, 4Ux, 4Zx  
xxF, xxU, xxV  
42T0819  
42T0821  
42T0823  
R
R
R
**  
**  
**  
xxE, xxJ, xxT  
xxA, xxB, xxG, xxH, xxK, xxL, xxM, xxP, xxQ, xxR,  
xxS, xxY  
(continued)  
Lenovo 3000 V100 and V200 93  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID ID  
14 ThinkPad 11a/b/g/n Wireless LAN Mini-PCI Express Adapter  
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Sx, 4Cx, 4Hx, 5Dx, 5Fx, 6Cx, 6Ex, 6Fx, 6Hx,  
7Dx, 7Fx, 7Gx, 2Vx, 3Nx, 4Kx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Mx, 5Nx, 5Qx, 5Rx,  
5Sx, 5Tx, 5Ux, 6Jx  
xxA, xxB, xxF, xxG, xxH, xxL, xxM, xxP, xxQ, xxS,  
xxU, xxY  
42T0825  
R
**  
xxE, xxJ  
42T0827  
42T0829  
42T0831  
42T0833  
R
R
R
R
**  
**  
**  
**  
xxV  
xxK  
xxT, xxR (802.11 b/g/n)  
Intel Wireless WiFi Link 4965AGN  
v 0764-23x, 24x, 25x, 28x, 29x, 2Ax, 2Dx, 32x, 42x, 43x, 47x, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx,  
4Kx  
xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxQ, xxS, xxU,  
xxV, xxY  
42T0865  
R
**  
xxG  
42T0867  
42T0871  
41W6381  
41R5808  
R
R
R
R
**  
**  
*
xxE, xxJ  
15 PCI Express Mini card slot cover for MT 0763  
PCI Express Mini card slot cover for MT 0764  
16 SATA hard disk drive, 40 GB, 9.5 mm, 5,400 rpm  
*
v 0763-34x, 59x, 77x, 97x, D9x, E3x, E7x, E9x, F3x, G3x, G9x, J3x, 3Ax, 6Bx, 7Ax, 7Bx,  
8Ax  
HGST  
27R2379  
27R2387  
R
R
R
**  
**  
**  
Toshiba  
SATA hard disk drive, 40 GB, 9.5 mm, 5,400 rpm, Fujitsu 42T1801  
v 0763-3Ax, 6Bx, 7Ax, 7Bx, 8Ax  
(continued)  
94 MT 0763 and 0764  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
16 SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm,  
Toshiba  
27R2389  
R
**  
v 0763-36x, 65x, 69x, 82x, 99x, A3x, B3x, C3x, C6x, C8x,  
E4x, E6x, J5x, 2Gx, 4Bx, 2Xx  
SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm, HGST 27R2381  
v 0763-36x, 65x, 69x, 82x, 99x, A3x, B3x, C3x, C6x, C8x,  
E4x, E6x, J5x, 2Gx, 4Bx, 2Xx  
R
**  
v 0764-22x  
SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm, Fujitsu 42T1803  
R
R
R
**  
**  
**  
v 0763-2Gx, 4Bx, 2Xx  
v 0764-22x  
SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm,  
Seagate  
v 0764-22x  
42T1851  
27R2391  
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm,  
Toshiba  
v 0763-22x, 23x, 25x, 26x, 33x, 38x, 49x, 62x, 66x, 83x,  
84x, 85x, 86x, 88x, 89x, 93x, A4x, A5x, B7x, C2x, C4x,  
C5x, C7x, C9x, D5x, E2x, E5x, E8x, G7x, J7x, J8x, 2Px,  
2Sx, 3Ex, 3Fx, 3Gx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax,  
5Ex, 5Fx, 6Ax, 6Dx, 6Ex, 7Cx,7Fx, 8Bx, 8Dx, 8Ex, 3Lx,  
4Tx, 4Yx, 5Kx, 5Px, 5Tx, 5Xx, 5Yx  
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm, HGST 27R2383  
v 0763-22x, 23x, 25x, 26x, 33x, 38x, 49x, 62x, 66x, 83x,  
84x, 85x, 86x, 88x, 89x, 93x, A4x, A5x, B7x, C2x, C4x,  
C5x, C7x, C9x, D5x, E2x, E5x, E8x, G7x, J7x, J8x, 2Px,  
2Sx, 3Ex, 3Fx, 3Gx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax,  
5Ex, 5Fx, 6Ax, 6Dx, 6Ex, 7Cx,7Fx, 8Bx, 8Dx, 8Ex, 3Lx,  
4Tx, 4Yx, 5Kx, 5Px, 5Tx, 5Xx, 5Yx  
R
**  
v 0764-23x, 26x, 28x, 29x, 2Lx, 2Mx, 44x, 45x, 46x, 4Lx,  
4Mx, 4Px, 4Qx, 4Rx, 4Tx  
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm, Fujitsu 42T1805  
v 0763-2Px, 3Ex, 3Fx, 3Gx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx,  
5Ax, 5Ex, 5Fx, 6Ax, 6Dx, 6Ex, 7Cx,7Fx, 8Bx, 8Dx, 8Ex,  
3Lx, 4Tx, 4Yx, 5Kx, 5Px, 5Tx, 5Xx, 5Yx  
R
R
**  
**  
v 0764-23x, 26x, 28x, 29x, 2Lx, 2Mx, 44x, 45x, 46x, 4Lx,  
4Mx, 4Px, 4Qx, 4Rx, 4Tx  
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm,  
Seagate  
42T1852  
v 0764-23x, 26x, 28x, 29x, 2Lx, 2Mx, 44x, 45x, 46x, 4Lx,  
4Mx, 4Px, 4Qx, 4Rx, 4Tx  
(continued)  
Lenovo 3000 V100 and V200 95  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID ID  
16 SATA hard disk drive, 100 GB, 9.5 mm, 5,400 rpm  
v 0763-27x, 29x, 43x, 44x, 46x, 64x, 68x, A2x, A6x, A8x, G2x, J9x, 2Cx, 2Dx, 2Ex, 2Fx,  
3Cx, 3Dx, 5Cx, 5Dx, 5Gx, 5Hx, 5Jx, 6Cx, 6Fx, 4Rx, 4Sx, 4Vx, 4Xx, 4Zx, 5Zx  
HGST  
27R2385  
27R2393  
42T1807  
R
R
R
**  
**  
**  
Toshiba  
SATA hard disk drive, 100 GB, 9.5 mm, 5,400 rpm,  
Fujitsu  
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 3Cx, 3Dx, 5Cx, 5Dx, 5Gx,  
5Hx, 5Jx, 6Cx, 6Fx, 4Rx, 4Sx, 4Vx, 4Xx, 4Zx, 5Zx  
SATA hard disk drive, 120 GB, 9.5 mm, 5,400 rpm,  
Toshiba  
v 0763-2Hx, 2Qx, 2Rx, 3Hx, 4Ax, 4Cx, 5Bx, 6Hx, 7Dx,  
7Ex, 7Gx, 8Cx, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx, 3Mx, 3Nx,  
4Jx, 4Kx, 4Nx, 4Ux, 5Mx, 5Nx, 5Qx, 5Rx, 5Sx, 5Ux,  
5Wx, 6Jx, 6Kx  
42T1815  
42T1809  
R
R
**  
**  
SATA hard disk drive, 120 GB, 9.5 mm, 5,400 rpm,  
Fujitsu  
v 0763-2Hx, 2Qx, 2Rx, 3Hx, 4Ax, 4Cx, 5Bx, 6Hx, 7Dx,  
7Ex, 7Gx, 8Cx, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx, 3Mx, 3Nx,  
4Jx, 4Kx, 4Nx, 4Ux, 5Mx, 5Nx, 5Qx, 5Rx, 5Sx, 5Ux,  
5Wx, 6Jx, 6Kx  
v 0764-24x, 27x, 2Ax, 32x, 42x, 43x, 47x, 48x, 4Ax, 4Cx,  
4Ex, 4Fx, 4Jx, 4Nx, 4Ux, 4Zx  
SATA hard disk drive, 120 GB, 9.5 mm, 5,400 rpm  
v 0764-24x, 27x, 2Ax, 32x, 42x, 43x, 47x, 48x, 4Ax, 4Cx, 4Ex, 4Fx, 4Jx, 4Nx, 4Ux, 4Zx  
HGST  
42T1848  
R
**  
Seagate  
42T1853  
R
**  
SATA hard disk drive, 160 GB, 9.5 mm, 5,400 rpm  
v 0764-25x, 2Bx, 2Cx, 2Dx, 49x, 4Bx, 4Dx, 4Gx, 4Hx, 4Kx  
HGST  
42T1849  
42T1854  
41W6380  
41R5807  
41W6379  
41R5806  
40Y8401  
R
R
R
R
R
R
R
**  
**  
*
Seagate  
17 Hard disk drive slot cover for MT 0763  
Hard disk drive slot cover for MT 0764  
18 DIMM slot cover for MT 0763  
DIMM slot cover for MT 0764  
*
*
*
19 256-MB DDR2-667 SDRAM SO-DIMM (PC2-5300)  
**  
cardꢀOPꢁ  
v 0763-B7x, G7x  
(continued)  
96 MT 0763 and 0764  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
19 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300)  
cardꢀOPꢁ  
40Y8402  
R
**  
v 0763-22x, 23x, 25x, 26x, 27x, 33x, 34x, 36x, 38x, 46x,  
49x, 59x, 62x, 64x, 65x, 66x, 68x, 69x, 77x, 82x, 83x,  
84x, 85x, 86x, 88x, 89x, 93x, 97x, 99x, A2x, A3x, A4x,  
A5x, A6x, A8x, B3x, C2x, C3x, C4x, C5x, C6x, C7x,  
C8x, C9x, D5x, D9x, E2x, E3x, E4x, E5x, E6x, E7x, E8x,  
E9x, F3x, G2x, G3x, G9x, J3x, J5x, J7x, J8x, J9x, 2Cx,  
2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx, 2Sx, 3Ax,  
3Ex, 3Fx, 3Gx, 3Hx, 4Ax, 4Bx, 4Dx, 4Ex, 4Fx, 4Gx,  
4Hx, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx,  
6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Ax, 7Bx, 7Cx,  
7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 8Bx, 8Cx, 8Dx, 8Ex, 2Lx,  
2Mx, 2Ux, 2Wx, 2Xx, 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx,  
4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx, 5Mx,  
5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Xx, 5Yx,  
5Zx, 6Jx, 6Kx  
v 0764-22x, 23x, 24x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,  
2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x,  
4Ax, 4Bx, 4Cx, 4Dx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx,  
4Tx, 4Zx  
1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) cardꢀOPꢁ 40Y8403  
v 0763-29x, 43x, 44x, 3Cx, 3Dx, 4Cx, 2Vx  
R
R
**  
**  
v 0764-2Dx, 4Ex, 4Fx, 4Jx, 4Ux  
2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) cardꢀOPꢁ 40Y8404  
v 0764-25x, 4Gx, 4Hx, 4Kx  
20 Backup battery  
21 Fan for MT 0763  
Fan for MT 0764  
92P1228  
41W6376  
41R5809  
92P1218  
R
R
R
R
N
N
N
*
22 Battery pack, Li-ion (3 cell), Sony  
v 0763-22x, 23x, 25x, 26x, 33x, 46x, 59x, 65x, 84x, 89x,  
97x, 99x, A4x, B3x, C3x, C5x, C7x, C8x, C9x, D5x,  
D9x, E2x, E3x, E5x, E6x, E7x, E9x, F3x, G3x, J7x, J8x,  
J9x  
Battery pack, Li-ion (3 cell), Sanyo  
92P1216  
R
*
v 0763-22x, 23x, 25x, 26x, 33x, 46x, 59x, 65x, 84x, 89x,  
97x, 99x, A4x, B3x, C3x, C5x, C7x, C8x, C9x, D5x,  
D9x, E2x, E3x, E5x, E6x, E7x, E9x, F3x, G3x, J7x, J8x,  
J9x, 2Gx, 2Px, 3Ax, 3Ex, 3Fx, 3Gx, 4Bx, 4Dx, 4Ex, 4Hx,  
5Cx, 5Dx, 5Jx, 6Ex, 7Cx, 8Bx, 8Cx, 8Dx, 8Ex, 2Lx, 2Xx,  
3Lx, 3Mx, 3Nx  
Battery pack, Li-ion (3 cell), Sanyo  
v 0764-22x, 2Bx, 32x, 44x, 4Px, 4Lx  
42T4508  
42T5220  
R
R
*
*
Battery pack, Li-ion (3 cell), Panasonic  
v 0763-2Gx, 2Px, 3Ax, 3Ex, 3Fx, 3Gx, 4Bx, 4Dx, 4Ex,  
4Hx, 5Cx, 5Dx, 5Jx, 6Ex, 7Cx, 8Bx, 8Cx, 8Dx, 8Ex, 2Lx,  
2Xx, 3Lx, 3Mx, 3Nx  
v 0764-22x, 2Bx, 32x, 44x, 4Px, 4Lx  
(continued)  
Lenovo 3000 V100 and V200 97  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
22 Battery pack, Li-ion (6 cell), Sony  
92P1222  
R
*
v 0763-27x, 29x, 34x, 36x, 38x, 43x, 44x, 49x, 62x, 64x,  
66x, 68x, 69x, 77x, 82x, 83x, 85x, 86x, 88x, 93x, A2x,  
A3x, A5x, A6x, A8x, B7x, C2x, C4x, C6x, E4x, E8x,  
G2x, G7x, G9x, J3x, J5x  
Battery pack, Li-ion (6 cell), Sanyo  
92P1220  
R
*
v 0763-27x, 29x, 34x, 36x, 38x, 43x, 44x, 49x, 62x, 64x,  
66x, 68x, 69x, 77x, 82x, 83x, 85x, 86x, 88x, 93x, A2x,  
A3x, A5x, A6x, A8x, B7x, C2x, C4x, C6x, E4x, E8x,  
G2x, G7x, G9x, J3x, J5x, 2Cx, 2Dx, 2Ex, 2Fx, 2Hx, 2Qx,  
2Rx, 2Sx, 3Cx, 3Dx, 3Hx, 4Ax, 4Cx, 4Fx, 4Gx, 5Ax,  
5Bx, 5Ex, 5Fx, 5Gx, 5Hx, 6Ax, 6Bx, 6Cx 6Dx, 6Fx, 6Hx,  
7Ax, 7Bx, 7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 2Mx, 2Ux, 2Vx,  
2Wx, 4Jx 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx,  
4Zx, 5Kx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux,  
5Wx, 5Xx, 5Yx, 5Zx, 6Jx, 6Kx  
Battery pack, Li-ion (6 cell), Sanyo  
42T4509  
42T5222  
R
R
*
*
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Cx, 2Dx,  
2Lx, 2Mx, 42x, 43x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx,  
4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Mx, 4Nx,  
4Qx, 4Rx, 4Tx, 4Ux, 4Zx  
Battery pack, Li-ion (6 cell), Panasonic  
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Hx, 2Qx, 2Rx, 3Cx, 3Dx,  
3Hx, 4Ax, 4Cx, 4Fx, 4Gx, 5Ax, 5Bx, 5Ex, 5Fx, 5Gx,  
5Hx, 6Ax, 6Bx, 6Cx 6Dx, 6Fx, 6Hx, 7Ax, 7Bx, 7Dx,  
7Ex, 7Fx, 7Gx, 8Ax, 2Mx, 2Ux, 2Vx, 2Wx, 4Jx, 4Kx,  
4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx,  
5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Xx,  
5Yx, 5Zx, 6Jx, 6Kx  
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Cx, 2Dx,  
2Lx, 2Mx, 42x, 43x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx,  
4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Mx, 4Nx,  
4Qx, 4Rx, 4Tx, 4Ux, 4Zx  
23 Heat sink assembly for MT 0763  
Heat sink assembly for MT 0764  
41W2639  
41R5804  
R
R
N
N
(continued)  
98 MT 0763 and 0764  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
24 CPU assembly, Intel Core Solo processor T1300 (1.66  
GHz) (667 MHz)  
41W1140  
R
N
v 0763-33x, 34x, 36x, 59x, 77x, 93x, 97x, 99x, B3x, B7x,  
D9x, F3x  
CPU assembly, Intel Core Duo processor T2050 (1.6  
GHz) (667 MHz)  
v 0763-J8x  
41W1461  
41W1463  
41W1132  
R
R
R
N
N
N
CPU assembly, Intel Core Duo processor T2250 (1.73  
GHz) (667 MHz)  
v 0763-J9x, 4Nx, 5Px, 5Qx, 5Rx  
CPU assembly, Intel Core Duo processor T2300 (1.66  
GHz)  
v 0763-23x, 25x, 27x, 38x, 62x, 64x, 65x, 69x, 82x, 83x,  
85x, 89x, A3x, A4x, A5x, C2x, C3x, C4x, C5x, C6x,  
C7x, C8x, C9x, D5x, E2x, E3x, E4x, E5x, E6x, E7x, E8x,  
E9x, G2x, G3x, G7x, G9x, J3x, J5x, J7x  
CPU assembly, Intel Core Duo processor T2350 (1.86  
GHz)  
v 0763-4Jx, 5Kx, 6Kx  
42W7660  
41W1329  
R
R
N
N
CPU assembly, Intel Core Duo processor T2300E (1.66  
GHz)  
v 0763-23x, 25x, 27x, 38x, 62x, 64x, 65x, 69x, 82x, 83x,  
85x, 89x, A3x, A4x, A5x, C2x, C3x, C4x, C5x, C6x,  
C7x, C8x, C9x, D5x, E2x, E3x, E4x, E5x, E6x, E7x, E8x,  
E9x, G2x, G3x, G7x, G9x, J3x, J5x, J7x  
CPU assembly, Intel Core Duo processor T2400 (1.83  
GHz)  
v 0763-22x, 26x, 43x, 46x, 49x, 66x, 84x, 86x, 88x  
41W1134  
41W1136  
41W1465  
R
R
R
N
N
N
CPU assembly, Intel Core Duo processor T2500 (2.0  
GHz)  
v 0763-29x, 44x, 68x, A2x, A6x, A8x  
CPU assembly, Intel Core 2 Duo processor T5200 (1.6  
GHz)  
v 0763- 2Lx, 2Mx, 2Xx, 4Vx, 4Xx, 4Zx, 5Mx, 5Nx, 5Tx.  
5Ux. 5Wx  
CPU assembly, Intel Core 2 Duo processor T5300 (1.73  
GHz)  
v 0763- 4Kx, 6Jx  
41R7755  
41W1409  
R
R
N
N
CPU assembly, Intel Core 2 Duo processor T5500 (1.66  
GHz)  
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 3Cx,3Ex, 3Fx, 3Gx, 3Hx,  
4Bx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 6Ax, 6Bx, 7Ax, 7Bx,  
8Ax, 8Bx, 3Lx, 5Xx, 5Yx, 5Zx  
CPU assembly, Intel Core 2 Duo processor T5600 (1.83  
GHz)  
41W1410  
R
N
v 0763-2Px, 2Qx, 2Sx, 3Ax, 5Ax, 5Bx, 5Cx, 5Ex, 5Fx,  
5Gx, 5Hx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Cx, 7Fx, 7Gx,  
8Cx, 8Dx, 8Ex, 3Mx, 4Rx, 4Sx, 4Tx, 4Ux, 4Yx  
(continued)  
Lenovo 3000 V100 and V200 99  
Parts list  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
24 CPU assembly, Intel Core 2 Duo processor T7100 (1.83  
GHz)  
42W7654  
R
N
v 0764-22x, 23x, 26x, 28x, 29x, 2Bx, 2Lx, 2Mx, 42x, 43x,  
44x, 45x, 46x, 4Cx, 4Dx, 4Ex, 4Fx, 4Jx, 4Lx, 4Mx, 4Px,  
4Qx, 4Rx, 4Tx, 4Ux  
CPU assembly, Intel Core 2 Duo processor T7200 (2.0  
GHz)  
41W1411  
42W7655  
42W7656  
R
R
R
N
N
N
v 0763-2Hx, 2Rx, 3Dx, 4Ax, 4Cx, 5Jx, 5Dx, 7Dx, 7Ex,  
2Ux, 2Vx, 2Wx, 3Nx, 5Sx  
CPU assembly, Intel Core 2 Duo processor T7300 (2.0  
GHz)  
v 0764-24x, 27x, 2Ax, 2Cx, 2Dx, 32x, 47x, 48x, 49x, 4Ax,  
4Nx, 4Zx  
CPU assembly, Intel Core 2 Duo processor T7500 (2.20  
GHz)  
v 0764-25x, 4Gx, 4Bx, 4Hx, 4Kx  
25 ExpressCard slot  
41W6378  
41W6384  
41R5811  
42W2200  
R
R
R
R
N
N
N
*
Label kit for MT 0763  
Label kit for MT 0764  
Blank bezel for ExpressCard slot and 5-1 Digital Media  
Reader  
100 MT 0763 and 0764  
Parts list  
LCD FRUs  
1
2
3
8
7
4
6
5
Lenovo 3000 V100 and V200 101  
 
Parts list  
12.1-in. WXGA TFT  
No. FRU  
FRU no.  
RoHS CRU  
ID  
ID  
N
N
N
N
N
N
1
2
LCD front bezel  
41W6369  
13N7184  
13N7182  
13N7180  
41W1322  
91P7032  
R
LCD panel, 12.1-in. WXGA AG, Samsung  
LCD panel, 12.1-in. WXGA AG, AUO  
LCD panel, 12.1-in. WXGA AG, CMO  
Inverter card  
R
R
R
3
4
R
LCD cable assembly, for no-camera  
R
v 0763-23x, 25x, 27x, 29x, 33x, 43x, 49x, 59x, 65x, 69x,  
77x, 83x, 85x, 93x, 97x, 99x, A3x, A5x, B3x, B7x, C3x,  
C5x, C7x, C9x, D5x, D9x, E3x, E5x, E7x, E9x, F3x,  
G3x, G7x, G9x, J3x, J5x, J7x, 3Ax, 3Ex, 3Gx, 3Hx, 4Ax,  
4Bx, 5Ax, 5Bx, 6Ax, 6Bx, 7Ax, 7Bx, 8Ax, 8Ex, 5Xx, 5Yx  
v 0764-22x, 42x, 43x, 44x, 45x, 46x, 4Ax, 4Lx, 4Px, 4Qx,  
4Rx  
LCD cable assembly, for camera  
91P7033  
R
N
v 0763-22x, 26x, 34x, 36x, 38x, 44x, 46x, 62x, 64x, 66x,  
68x, 82x, 84x, 86x, 88x, 89x, A2x, A4x, A6x, A8x, C2x,  
C4x, C6x, C8x, E2x, E4x, E6x, E8x, G2x, J8x, J9x, 2Cx,  
2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx, 2Sx, 3Cx,  
3Dx, 3Fx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Cx, 5Dx,  
5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Cx,  
7Dx, 7Ex, 7Fx, 7Gx, 8Bx, 8Cx, 8Dx, 2Lx, 2Mx, 2Ux,  
2Vx, 2Wx, 2Xx, 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx, 4Rx,  
4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx, 5Mx, 5Nx,  
5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Zx, 6Jx, 6Kx  
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,  
2Dx, 2Lx, 2Mx, 32x, 47x, 48x, 49x, 4Bx, 4Cx, 4Dx, 4Ex,  
4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Nx, 4Tx, 4Ux, 4Zx  
5
6
LCD rear cover  
41W2638  
91P7034  
41R5800  
41W6370  
41W1331  
R
R
R
R
R
N
N
N
N
N
Antenna assembly for MT 0763  
Antenna assembly for MT 0764  
Hinges  
7
8
Integrated camera  
v 0763-22x, 26x, 34x, 36x, 38x, 44x, 46x, 62x, 64x, 66x,  
68x, 82x, 84x, 86x, 88x, 89x, A2x, A4x, A6x, A8x, C2x,  
C4x, C6x, C8x, E2x, E4x, E6x, E8x, G2x, J8x, J9x, 2Cx,  
2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx, 2Sx, 3Cx,  
3Dx, 3Fx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Cx, 5Dx,  
5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Cx,  
7Dx, 7Ex, 7Fx, 7Gx, 8Bx, 8Cx, 8Dx, 2Lx, 2Mx, 2Ux,  
2Vx, 2Wx, 2Xx, 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx, 4Rx,  
4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx, 5Mx, 5Nx,  
5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Zx, 6Jx, 6Kx  
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,  
2Dx, 2Lx, 2Mx, 32x, 47x, 48x, 49x, 4Bx, 4Cx, 4Dx, 4Ex,  
4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Nx, 4Tx, 4Ux, 4Zx  
102 MT 0763 and 0764  
 
Parts list  
Keyboard  
Keyboard for MT 0763  
Language  
P/N  
P/N  
RoHS CRU  
(NMB)  
(Chicony) ID  
ID  
Arabic  
39T7368  
39T7365  
39T7379  
39T7373  
39T7362  
39T7359  
39T7357  
39T7353  
39T7383  
39T7360  
39T7355  
39T7354  
39T7358  
39T7356  
39T7375  
39T7370  
39T7374  
42T3006  
39T7363  
39T7378  
39T7380  
39T7361  
39T7371  
39T7367  
39T7384  
39T7369  
39T7377  
39T7376  
39T7364  
39T7381  
39T7366  
39T7382  
39T7372  
39T7432  
39T7429  
39T7443  
39T7437  
39T7426  
39T7423  
39T7421  
39T7417  
39T7447  
39T7424  
39T7419  
39T7418  
39T7422  
39T7420  
39T7439  
39T7434  
39T7438  
R
N
Belgian  
Chinese, Traditional  
Czech  
Danish  
Dutch  
English, U.K.  
English, U.S.  
English, U.S. (International, with a Euro symbol)  
Finnish, Swedish  
French, Canadian (058)  
French, Canadian, Acnor  
French, European  
German  
Greek  
Hebrew  
Hungarian  
Iceland  
Italian  
39T7427  
39T7442  
39T7444  
39T7425  
39T7435  
39T7431  
39T7448  
39T7433  
39T7441  
39T7440  
39T7428  
39T7445  
39T7430  
39T7446  
39T7436  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese  
Portuguese, Brazilian  
Russian  
Slovak  
Slovenian  
Spanish, European  
Spanish, Latin American  
Swiss  
Thai  
Turkish  
Lenovo 3000 V100 and V200 103  
 
Parts list  
Keyboard for MT 0764  
Language  
P/N  
P/N  
RoHS CRU  
(NMB)  
(Chicony) ID  
ID  
Arabic  
42T3353  
42T3350  
42T3364  
42T3358  
42T3347  
42T3344  
42T3342  
42T3338  
42T3368  
42T3345  
42T3340  
42T3339  
42T3343  
42T3341  
42T3360  
42T3355  
42T3359  
42T3370  
42T3348  
42T3363  
42T3365  
42T3346  
42T3356  
42T3352  
42T3369  
42T3354  
42T3362  
42T3361  
42T3349  
42T3366  
42T3351  
42T3367  
42T3357  
42T3418  
42T3415  
42T3429  
42T3423  
42T3412  
42T3409  
42T3407  
42T3403  
42T3433  
42T3410  
42T3405  
42T3404  
42T3408  
42T3406  
42T3425  
42T3420  
42T3424  
R
N
Belgian  
Chinese, Traditional  
Czech  
Danish  
Dutch  
English, U.K.  
English, U.S.  
English, U.S. (International, with a Euro symbol)  
Finnish, Swedish  
French, Canadian (058)  
French, Canadian, Acnor  
French, European  
German  
Greek  
Hebrew  
Hungarian  
Iceland  
Italian  
42T3413  
42T3428  
42T3430  
42T3411  
42T3421  
42T3417  
42T3434  
42T3419  
42T3427  
42T3426  
42T3414  
42T3431  
42T3416  
42T3432  
42T3422  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese  
Portuguese, Brazilian  
Russian  
Slovak  
Slovenian  
Spanish, European  
Spanish, Latin American  
Swiss  
Thai  
Turkish  
104 MT 0763 and 0764  
 
Parts list  
Recovery discs  
Windows XP Professional CDs  
Windows XP Professional is preinstalled as the operating system in the following  
models:  
v 0763-22x, 23x, 27x, 29x, 43x, 44x, 46x, 49x, 84x, 88x, 89x, A3x, A6x, B3x, C4x, D5x,  
E5x, E8x, F3x, G2x, J3x, J5x, J7x, 2Dx, 2Fx, 2Hx, 2Rx, 3Dx, 3Fx, 3Hx, 4Ax, 4Cx,  
4Ex, 4Fx, 4Hx, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Gx, 5Jx, 6Ax, 7Ax, 7Cx, 7Dx, 7Ex, 7Fx,  
8Ax, 8Cx, 8Ex  
Language  
P/N  
RoHS CRU  
ID  
ID  
Arabic  
43T3842  
43T3835  
43T3836  
43T3837  
43T3841  
43T3831  
43T3834  
43T3824  
43T3823  
43T3832  
43T3825  
43T3826  
43T3846  
43T3839  
43T3845  
43T3828  
43T3838  
43T3847  
43T3833  
43T3840  
43T3829  
43T3843  
43T3849  
43T3827  
43T3848  
43T3830  
43T3844  
R
*
Chinese, Simplified  
Chinese, Traditional  
Chinese, Traditional (Hong Kong S.A.R.)  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hebrew, English enabled  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese, Brazilian  
Russian  
Russian, English Enabled  
Spanish  
Slovenian  
Swedish  
Turkish  
Lenovo 3000 V100 and V200 105  
 
Parts list  
Windows XP Home Edition CDs  
Windows XP Home Edition is preinstalled as the operating system in the following  
models:  
v 0763-25x, 26x, 33x, 34x, 36x, 38x, 59x, 62x, 64x, 65x, 66x, 68x, 69x, 77x, 82x, 83x,  
85x, 86x, 93x, 99x, A2x, A4x, A5x, A8x, B7x, C2x, C5x, C6x, C7x, C9x, D9x, E3x,  
E4x, E6x, E7x, E9x, G7x, G9x, J8x, J9x, 2Cx, 2Ex, 2Gx, 2Px, 2Qx, 2Sx, 3Ax, 3Cx,  
3Ex, 3Gx, 4Bx, 4Dx, 4Gx, 5Fx, 5Hx, 6Bx, 6Cx, 6Ex, 6Fx, 6Hx, 7Bx, 7Gx, 8Bx, 8Dx  
Language  
P/N  
RoHS CRU  
ID  
ID  
Arabic  
43T4058  
43T4051  
43T4052  
43T4053  
43T4057  
43T4047  
43T4050  
43T4040  
43T4039  
43T4048  
43T4041  
43T4042  
43T4062  
43T4065  
43T4055  
43T4061  
43T4044  
43T4054  
43T4063  
43T4049  
43T4056  
43T4045  
43T4059  
43T4064  
43T4043  
43T4046  
43T4060  
R
*
Chinese, Simplified  
Chinese, Traditional  
Chinese, Traditional (Hong Kong S.A.R.)  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hebrew  
Hebrew, English enabled  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese, Brazilian  
Russian  
Russian, English enabled  
Spanish  
Swedish  
Turkish  
106 MT 0763 and 0764  
 
Parts list  
Windows Vista Home Premium (32 bit) DVDs for MT 0763  
Windows Vista Home Premium is preinstalled as the operating system in the  
following models:  
v 0763-2Lx, 3Nx, 4Jx, 4Nx, 4Vx, 4Zx, 5Wx, 5Xx, 5Zz  
Language  
P/N  
RoHS CRU  
ID  
ID  
Chinese, Traditional  
43T7173  
43T7174  
43T7166  
43T7909  
43T7165  
43T7155  
43T7154  
43T7167  
43T7156  
43T7157  
43T7172  
43T7176  
43T7171  
43T7160  
43T7161  
43T7175  
43T7905  
43T7168  
43T7159  
43T7169  
43T7821  
43T7932  
43T7158  
43T7907  
43T7170  
R
*
Chinese, Traditional (Hong Kong S.A.R.)  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hebrew  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese, Brazilian  
Russian  
Russian, English enabled  
Slovenian  
Spanish  
Swedish  
Turkish  
Lenovo 3000 V100 and V200 107  
 
Parts list  
Windows Vista Home Premium (32 bit) DVDs for MT 0764  
Windows Vista Home Premium is preinstalled as the operating system in the  
following models:  
v 0764-24x, 2Ax, 2Bx, 43x, 46x, 49x, 4Dx, 4Rx  
Language  
P/N  
RoHS CRU  
ID  
ID  
Bulgarian  
44Y0027  
44Y0004  
44Y0011  
44Y0014  
44Y0028  
44Y0020  
44Y0012  
44Y0016  
44Y0001  
44Y0000  
44Y0013  
44Y0005  
44Y0006  
44Y0022  
44Y0007  
44Y0023  
44Y0008  
44Y0009  
44Y0015  
44Y0017  
44Y0021  
44Y0024  
44Y0003  
44Y0029  
44Y0018  
44Y0002  
44Y0030  
44Y0031  
44Y0025  
44Y0010  
44Y0019  
44Y0026  
44Y0032  
R
*
Chinese, Simplified  
Chinese, Traditional  
Chinese, Traditional (Hong Kong S.A.R.)  
Croatian  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hebrew  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese  
Portuguese, Brazilian  
Romanian  
Russian  
Russian, English enabled  
Serbian-Latin  
Slovak  
Slovenian  
Spanish  
Swedish  
Turkish  
Ukrainian  
108 MT 0763 and 0764  
 
Parts list  
Windows Vista Home Basic (32 bit) DVDs for MT 0763  
Windows Vista Home Basic is preinstalled as the operating system in the following  
models:  
v 0763-2Xx, 3Lx, 4Sx, 4Tx, 4Ux, 4Xx, 4Yx, 5Kx, 5Px, 5Sx, 5Tx  
Language  
P/N  
RoHS CRU  
ID  
ID  
Chinese, Traditional  
43T7127  
43T7128  
43T7120  
43T7903  
43T7119  
43T7109  
43T7108  
43T7121  
43T7110  
43T7111  
43T7126  
43T7130  
43T7125  
43T7114  
43T7115  
43T7129  
43T7899  
43T7122  
43T7113  
43T7123  
43T7820  
43T7931  
43T7112  
43T7901  
43T7124  
R
*
Chinese, Traditional (Hong Kong S.A.R.)  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hebrew  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese, Brazilian  
Russian  
Russian, English enabled  
Slovenian  
Spanish  
Swedish  
Turkish  
Lenovo 3000 V100 and V200 109  
 
Parts list  
Windows Vista Home Basic (32 bit) DVDs for MT 0764  
Windows Vista Home Basic is preinstalled as the operating system in the following  
models:  
v 0764-22x, 44x, 48x, 4Cx, 4Fx, 4Hx, 4Jx, 4Lx, 4Px, 4Ux  
Language  
P/N  
RoHS CRU  
ID  
ID  
Chinese, Simplified  
44Y0069  
44Y0076  
44Y0079  
44Y0085  
44Y0077  
44Y0081  
44Y0066  
44Y0065  
44Y0078  
44Y0070  
44Y0071  
44Y0087  
44Y0072  
44Y0088  
44Y0073  
44Y0074  
44Y0080  
44Y0082  
44Y0086  
44Y0068  
44Y0083  
44Y0067  
44Y0089  
44Y0075  
44Y0084  
44Y0090  
R
*
Chinese, Traditional  
Chinese, Traditional (Hong Kong S.A.R.)  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hebrew  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese, Brazilian  
Russian  
Russian, English enabled  
Slovenian  
Spanish  
Swedish  
Turkish  
110 MT 0763 and 0764  
 
Parts list  
Windows Vista Business (32 bit) DVDs for MT 0763  
Windows Vista Business is preinstalled as the operating system in the following  
models:  
v 0763-2Mx, 2Ux, 2Vx, 2Wx, 3Mx, 4Kx, 4Rx, 5Mx, 5Nx, 5Qx, 5Rx, 5Ux, 5Yx, 6Jx,  
6Kx  
Language  
P/N  
RoHS CRU  
ID  
ID  
Chinese, Traditional  
43T7081  
43T7082  
43T7074  
43T7897  
43T7073  
43T7063  
43T7062  
43T7075  
43T7064  
43T7065  
43T7080  
43T7084  
43T7079  
43T7068  
43T7069  
43T7083  
43T7893  
43T7076  
43T7067  
43T7077  
43T7818  
43T7929  
43T7066  
43T7895  
43T7078  
R
*
Chinese, Traditional (Hong Kong S.A.R.)  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hebrew  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese, Brazilian  
Russian  
Russian, English enabled  
Slovenian  
Spanish  
Swedish  
Turkish  
Lenovo 3000 V100 and V200 111  
 
Parts list  
Windows Vista Business (32 bit) DVDs for MT 0764  
Windows Vista Business is preinstalled as the operating system in the following  
models:  
v 0764-23x 26x, 27x, 28x, 29x, 2Cx, 2Lx, 2Mx, 32x, 42x, 45x, 47x, 4Ax, 4Bx, 4Ex,  
4Mx, 4Nx, 4Qx, 4Tx, 4Zx  
Language  
P/N  
RoHS CRU  
ID  
ID  
Bulgarian  
44Y0059  
44Y0037  
44Y0043  
44Y0046  
44Y0060  
44Y0052  
44Y0044  
44Y0048  
44Y0034  
44Y0033  
44Y0045  
44Y0038  
44Y0039  
44Y0054  
44Y0055  
44Y0040  
44Y0041  
44Y0047  
44Y0049  
44Y0053  
44Y0056  
44Y0036  
44Y0061  
44Y0050  
44Y0035  
44Y0062  
44Y0063  
44Y0057  
44Y0042  
44Y0051  
44Y0058  
44Y0064  
R
*
Chinese, Simplified  
Chinese, Traditional  
Chinese, Traditional (Hong Kong S.A.R.)  
Croatian  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese  
Portuguese, Brazilian  
Romanian  
Russian  
Russian, English enabled  
Serbian-Latin  
Slovak  
Slovenian  
Spanish  
Swedish  
Turkish  
Ukrainian  
112 MT 0763 and 0764  
 
Parts list  
Windows Vista Ultimate (32 bit) DVDs  
Windows Vista Ultimate is preinstalled as the operating system in the following  
models:  
v 0764-25x, 2Dx, 4Gx, 4Kx  
Language  
P/N  
RoHS CRU  
ID  
ID  
Chinese, Simplified  
44Y0095  
44Y0101  
44Y0104  
44Y0110  
44Y0102  
44Y0106  
44Y0092  
44Y0091  
44Y0103  
44Y0096  
44Y0097  
44Y0112  
44Y0113  
44Y0098  
44Y0099  
44Y0105  
44Y0107  
44Y0111  
44Y0094  
44Y0108  
44Y0093  
44Y0100  
44Y0114  
44Y0109  
44Y0115  
R
*
Chinese, Traditional  
Chinese, Traditional (Hong Kong S.A.R.)  
Czech  
Danish  
Dutch  
English, (UD) U.K. with disabled modem and WLAN  
English, U.S., U.K. with enabled modem and WLAN  
Finnish  
French  
German  
Greek  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese, Brazilian  
Russian  
Russian, English enabled  
Spanish  
Slovenian  
Swedish  
Turkish  
Lenovo 3000 V100 and V200 113  
 
Parts list  
Corel software CDs  
Language  
P/N  
RoHS CRU  
ID  
ID  
English, U.S.  
French  
41X0440  
41X0443  
41X0608  
41X0449  
41X0446  
R
*
Japanese  
Portuguese, Brazilian  
Spanish  
Miscellaneous parts  
FRU  
P/N  
RoHS CRU  
ID  
ID  
Screw kit, (including nylon-coated screws) for MT 0763:  
41W6383  
R
N
v M2 × 2 mm (silver), pan-head (4)  
v M2 × 2.5 mm (silver), pan-head (13)  
v M2 × 3 mm (silver), pan-head (6)  
v M2 × 4 mm (silver), pan-head (13)  
v M2.5 × 5 mm (black), pan-head (10)  
v M2.5 × 5 mm (silver), pan-head (20)  
v M2.5 × 7 mm (black), pan-head (1)  
v M2.5 × 13 mm (silver), pan-head (2)  
v M3 × 2.8 mm (silver), pan-head (4)  
v Hex stud (2)  
v Screw cap rubber (6)  
Screw kit, (including nylon-coated screws) for MT 0764:  
v M2 x 4 mm (silver), pan-head (2)  
41R5810  
41W6382  
R
R
N
N
v M2.5 x 5 mm (silver), pan-head (20)  
v M2.5 x 13 mm (silver), pan-head (2)  
System miscellaneous parts:  
v Bracket, digital media reader  
v Bracket, fingerprint reader  
v Bracket, optical drive  
v Bracket, touch pad  
v ExpressCard slot blank bezel  
v Digital media reader blank bezel  
v Rubber foot  
v Screw cap rubber  
Cable miscellaneous parts for MT 0763  
91P7035  
41R5812  
R
R
N
N
Cable miscellaneous parts for MT 0764:  
v MDC cable  
v Fingerprint reader cable  
v Launch board cable  
v Bluetooth cable  
v Digital media reader FCC  
114 MT 0763 and 0764  
 
Parts list  
AC adapters  
FRU  
P/N  
RoHS CRU  
ID  
ID  
2-pin (65 W, 20 V) adapter (models xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY) ꢀOPꢁ  
Delta  
92P1155  
92P1159  
92P1214  
R
R
R
*
*
*
Lite-On  
Astec  
3-pin (65W, 20 V) adapter (models xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxR, xxT, xxV)  
ꢀOPꢁ  
Delta  
92P1153  
92P1157  
92P1212  
R
R
R
*
*
*
Lite-On  
Astec  
Common parts list  
Tools  
Tool  
P/N  
Triconnector wrap plug  
Audio wrap cable  
72X8546  
66G5180  
05K2580  
95F3598  
00P7033  
1650840  
93F2838  
00P6967  
08K7159  
27K9813  
USB parallel test cable  
Screwdriver kit  
Mini PC tool set  
1/4" drive spinner handle  
1/4" Sq. to 1/4" hex torx adapter  
TR7-TR-10 tamper resistant torx bits  
Removal tool antenna RF connector  
PCI-Express/USB wrap card  
CE Utility Diskette for Lenovo 3000 notebooks  
Note: Download the file from the following Web site: http://www.lenovo.com/  
Lenovo 3000 V100 and V200 115  
 
Parts list  
Power cords  
A Lenovo 3000 power cord for a specific country or region is usually available only  
in that country or region:  
For 2-pin power cords:  
Region  
P/N  
(Longwell)  
P/N (Volex) RoHS  
ID  
CRU  
ID  
Argentina  
Brazil  
42T5020  
42T5026  
42T5008  
42T5014  
42T5105  
42T5111  
42T5093  
42T5099  
R
*
Canada, U.S.  
Japan  
For 3-pin power cords:  
Region  
P/N  
(Longwell)  
P/N (Volex) RoHS  
ID  
CRU  
ID  
Australia, New Zealand  
42T5050  
42T5041  
42T5029  
42T5035  
42T5083  
42T5062  
42T5047  
42T5077  
42T5056  
42T5044  
42T5004  
42T5135  
42T5126  
42T5114  
42T5120  
42T5168  
42T5147  
42T5132  
42T5162  
42T5141  
42T5129  
42T5089  
R
*
Denmark  
Europe  
Hong Kong S.A.R. of China, U.K.  
India  
Israel  
Italy  
Korea  
South Africa  
Switzerland  
Thailand, Taiwan  
116 MT 0763 and 0764  
 
Notices  
Notices  
Lenovo may not offer the products, services, or features discussed in this  
document in all countries. Consult your local Lenovo representative for  
information on the products and services currently available in your area. Any  
reference to a Lenovo product, program, or service is not intended to state or  
imply that only that Lenovo product, program, or service may be used. Any  
functionally equivalent product, program, or service that does not infringe any  
Lenovo intellectual property right may be used instead. However, it is the user’s  
responsibility to evaluate and verify the operation of any other product, program,  
or service.  
Lenovo may have patents or pending patent applications covering subject matter  
described in this document. The furnishing of this document does not give you  
any license to these patents. You can send license inquiries, in writing, to:  
Lenovo (United States), Inc.  
1009 Think Place - Building One  
Morrisville, NC 27560  
U.S.A.  
Attention: Lenovo Director of Licensing  
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF  
ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED  
TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some  
jurisdictions do not allow disclaimer of express or implied warranties in certain  
transactions, therefore, this statement may not apply to you.  
This information could include technical inaccuracies or typographical errors.  
Changes are periodically made to the information herein; these changes will be  
incorporated in new editions of the publication. Lenovo may make improvements  
and/or changes in the product(s) and/or the program(s) described in this  
publication at any time without notice.  
The products described in this document are not intended for use in implantation  
or other life support applications where malfunction may result in injury or death  
to persons. The information contained in this document does not affect or change  
Lenovo product specifications or warranties. Nothing in this document shall  
operate as an express or implied license or indemnity under the intellectual  
property rights of Lenovo or third parties. All information contained in this  
document was obtained in specific environments and is presented as an  
illustration. The result obtained in other operating environments may vary.  
Lenovo may use or distribute any of the information you supply in any way it  
believes appropriate without incurring any obligation to you.  
Any references in this publication to non-Lenovo Web sites are provided for  
convenience only and do not in any manner serve as an endorsement of those Web  
sites. The materials at those Web sites are not part of the materials for this Lenovo  
product, and use of those Web sites is at your own risk.  
Any performance data contained herein was determined in a controlled  
environment. Therefore, the result obtained in other operating environments may  
vary significantly. Some measurements may have been made on development-level  
systems and there is no guarantee that these measurements will be the same on  
generally available systems. Furthermore, some measurements may have been  
Lenovo 3000 V100 and V200 117  
 
Notices  
estimated through extrapolation. Actual results may vary. Users of this document  
should verify the applicable data for their specific environment.  
Trademarks  
The following terms are trademarks of Lenovo in the United States, other countries  
or both:  
Lenovo  
Lenovo Care  
Rescue and Recovery  
ThinkPad  
The following terms are trademarks of the International Business Machines  
Corporation in the United States, other countries, or both:  
IBM (used under license)  
The following terms are trademarks of Microsoft Corporation in the United States,  
other countries, or both:  
Microsoft®  
Windows®  
Windows Vista  
The following are trademarks of Intel Corporation or its subsidiaries in the United  
States, other countries, or both:  
Intel®  
Intel® Core™  
Intel® CoreDuo  
Intel® CoreSolo  
Intel® Core2 Duo  
Other company, product, or service names may be the trademarks or service marks  
of others.  
118 MT 0763 and 0764  
 
Trademarks  
Lenovo 3000 V100 and V200 119  
Part Number: 42X3554  
(1P) P/N: 42X3554  

Intel Box Motherboard Matx Xeon S1155 DBS1200V3RPS User Manual
JVC AV 28KH1BUF User Manual
JVC LCT1821 001A U User Manual
Lenovo 6533 User Manual
Miele Cooktop KM 424 User Manual
Philips 2 32E+04 User Manual
Philips 170x7 User Manual
Philips DVP4080 User Manual
Philips PR1920C6 User Manual
Philips ScanCard SC3136N User Manual